| /* |
| * Driver for Atmel QSPI Controller |
| * |
| * Copyright (C) 2015 Atmel Corporation |
| * |
| * Author: Cyrille Pitchen <cyrille.pitchen@atmel.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, but WITHOUT |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for |
| * more details. |
| * |
| * You should have received a copy of the GNU General Public License along with |
| * this program. If not, see <http://www.gnu.org/licenses/>. |
| * |
| * This driver is based on drivers/mtd/spi-nor/fsl-quadspi.c from Freescale. |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/clk.h> |
| #include <linux/module.h> |
| #include <linux/platform_device.h> |
| #include <linux/delay.h> |
| #include <linux/err.h> |
| #include <linux/interrupt.h> |
| #include <linux/mtd/mtd.h> |
| #include <linux/mtd/partitions.h> |
| #include <linux/mtd/spi-nor.h> |
| #include <linux/platform_data/atmel.h> |
| #include <linux/of.h> |
| |
| #include <linux/io.h> |
| #include <linux/gpio.h> |
| #include <linux/pinctrl/consumer.h> |
| |
| /* QSPI register offsets */ |
| #define QSPI_CR 0x0000 /* Control Register */ |
| #define QSPI_MR 0x0004 /* Mode Register */ |
| #define QSPI_RD 0x0008 /* Receive Data Register */ |
| #define QSPI_TD 0x000c /* Transmit Data Register */ |
| #define QSPI_SR 0x0010 /* Status Register */ |
| #define QSPI_IER 0x0014 /* Interrupt Enable Register */ |
| #define QSPI_IDR 0x0018 /* Interrupt Disable Register */ |
| #define QSPI_IMR 0x001c /* Interrupt Mask Register */ |
| #define QSPI_SCR 0x0020 /* Serial Clock Register */ |
| |
| #define QSPI_IAR 0x0030 /* Instruction Address Register */ |
| #define QSPI_ICR 0x0034 /* Instruction Code Register */ |
| #define QSPI_IFR 0x0038 /* Instruction Frame Register */ |
| |
| #define QSPI_SMR 0x0040 /* Scrambling Mode Register */ |
| #define QSPI_SKR 0x0044 /* Scrambling Key Register */ |
| |
| #define QSPI_WPMR 0x00E4 /* Write Protection Mode Register */ |
| #define QSPI_WPSR 0x00E8 /* Write Protection Status Register */ |
| |
| #define QSPI_VERSION 0x00FC /* Version Register */ |
| |
| |
| /* Bitfields in QSPI_CR (Control Register) */ |
| #define QSPI_CR_QSPIEN BIT(0) |
| #define QSPI_CR_QSPIDIS BIT(1) |
| #define QSPI_CR_SWRST BIT(7) |
| #define QSPI_CR_LASTXFER BIT(24) |
| |
| /* Bitfields in QSPI_MR (Mode Register) */ |
| #define QSPI_MR_SSM BIT(0) |
| #define QSPI_MR_LLB BIT(1) |
| #define QSPI_MR_WDRBT BIT(2) |
| #define QSPI_MR_SMRM BIT(3) |
| #define QSPI_MR_CSMODE_MASK GENMASK(5, 4) |
| #define QSPI_MR_CSMODE_NOT_RELOADED (0 << 4) |
| #define QSPI_MR_CSMODE_LASTXFER (1 << 4) |
| #define QSPI_MR_CSMODE_SYSTEMATICALLY (2 << 4) |
| #define QSPI_MR_NBBITS_MASK GENMASK(11, 8) |
| #define QSPI_MR_NBBITS(n) ((((n) - 8) << 8) & QSPI_MR_NBBITS_MASK) |
| #define QSPI_MR_DLYBCT_MASK GENMASK(23, 16) |
| #define QSPI_MR_DLYBCT(n) (((n) << 16) & QSPI_MR_DLYBCT_MASK) |
| #define QSPI_MR_DLYCS_MASK GENMASK(31, 24) |
| #define QSPI_MR_DLYCS(n) (((n) << 24) & QSPI_MR_DLYCS_MASK) |
| |
| /* Bitfields in QSPI_SR/QSPI_IER/QSPI_IDR/QSPI_IMR */ |
| #define QSPI_SR_RDRF BIT(0) |
| #define QSPI_SR_TDRE BIT(1) |
| #define QSPI_SR_TXEMPTY BIT(2) |
| #define QSPI_SR_OVRES BIT(3) |
| #define QSPI_SR_CSR BIT(8) |
| #define QSPI_SR_CSS BIT(9) |
| #define QSPI_SR_INSTRE BIT(10) |
| #define QSPI_SR_QSPIENS BIT(24) |
| |
| #define QSPI_SR_CMD_COMPLETED (QSPI_SR_INSTRE | QSPI_SR_CSR) |
| |
| /* Bitfields in QSPI_SCR (Serial Clock Register) */ |
| #define QSPI_SCR_CPOL BIT(0) |
| #define QSPI_SCR_CPHA BIT(1) |
| #define QSPI_SCR_SCBR_MASK GENMASK(15, 8) |
| #define QSPI_SCR_SCBR(n) (((n) << 8) & QSPI_SCR_SCBR_MASK) |
| #define QSPI_SCR_DLYBS_MASK GENMASK(23, 16) |
| #define QSPI_SCR_DLYBS(n) (((n) << 16) & QSPI_SCR_DLYBS_MASK) |
| |
| /* Bitfields in QSPI_ICR (Instruction Code Register) */ |
| #define QSPI_ICR_INST_MASK GENMASK(7, 0) |
| #define QSPI_ICR_INST(inst) (((inst) << 0) & QSPI_ICR_INST_MASK) |
| #define QSPI_ICR_OPT_MASK GENMASK(23, 16) |
| #define QSPI_ICR_OPT(opt) (((opt) << 16) & QSPI_ICR_OPT_MASK) |
| |
| /* Bitfields in QSPI_IFR (Instruction Frame Register) */ |
| #define QSPI_IFR_WIDTH_MASK GENMASK(2, 0) |
| #define QSPI_IFR_WIDTH_SINGLE_BIT_SPI (0 << 0) |
| #define QSPI_IFR_WIDTH_DUAL_OUTPUT (1 << 0) |
| #define QSPI_IFR_WIDTH_QUAD_OUTPUT (2 << 0) |
| #define QSPI_IFR_WIDTH_DUAL_IO (3 << 0) |
| #define QSPI_IFR_WIDTH_QUAD_IO (4 << 0) |
| #define QSPI_IFR_WIDTH_DUAL_CMD (5 << 0) |
| #define QSPI_IFR_WIDTH_QUAD_CMD (6 << 0) |
| #define QSPI_IFR_INSTEN BIT(4) |
| #define QSPI_IFR_ADDREN BIT(5) |
| #define QSPI_IFR_OPTEN BIT(6) |
| #define QSPI_IFR_DATAEN BIT(7) |
| #define QSPI_IFR_OPTL_MASK GENMASK(9, 8) |
| #define QSPI_IFR_OPTL_1BIT (0 << 8) |
| #define QSPI_IFR_OPTL_2BIT (1 << 8) |
| #define QSPI_IFR_OPTL_4BIT (2 << 8) |
| #define QSPI_IFR_OPTL_8BIT (3 << 8) |
| #define QSPI_IFR_ADDRL BIT(10) |
| #define QSPI_IFR_TFRTYP_MASK GENMASK(13, 12) |
| #define QSPI_IFR_TFRTYP_TRSFR_READ (0 << 12) |
| #define QSPI_IFR_TFRTYP_TRSFR_READ_MEM (1 << 12) |
| #define QSPI_IFR_TFRTYP_TRSFR_WRITE (2 << 12) |
| #define QSPI_IFR_TFRTYP_TRSFR_WRITE_MEM (3 << 13) |
| #define QSPI_IFR_CRM BIT(14) |
| #define QSPI_IFR_NBDUM_MASK GENMASK(20, 16) |
| #define QSPI_IFR_NBDUM(n) (((n) << 16) & QSPI_IFR_NBDUM_MASK) |
| |
| /* Bitfields in QSPI_SMR (Scrambling Mode Register) */ |
| #define QSPI_SMR_SCREN BIT(0) |
| #define QSPI_SMR_RVDIS BIT(1) |
| |
| /* Bitfields in QSPI_WPMR (Write Protection Mode Register) */ |
| #define QSPI_WPMR_WPEN BIT(0) |
| #define QSPI_WPMR_WPKEY_MASK GENMASK(31, 8) |
| #define QSPI_WPMR_WPKEY(wpkey) (((wpkey) << 8) & QSPI_WPMR_WPKEY_MASK) |
| |
| /* Bitfields in QSPI_WPSR (Write Protection Status Register) */ |
| #define QSPI_WPSR_WPVS BIT(0) |
| #define QSPI_WPSR_WPVSRC_MASK GENMASK(15, 8) |
| #define QSPI_WPSR_WPVSRC(src) (((src) << 8) & QSPI_WPSR_WPVSRC) |
| |
| |
| struct atmel_qspi { |
| void __iomem *regs; |
| void __iomem *mem; |
| struct clk *clk; |
| struct platform_device *pdev; |
| u32 pending; |
| |
| struct spi_nor nor; |
| u32 clk_rate; |
| struct completion cmd_completion; |
| }; |
| |
| struct atmel_qspi_command { |
| union { |
| struct { |
| u32 instruction:1; |
| u32 address:3; |
| u32 mode:1; |
| u32 dummy:1; |
| u32 data:1; |
| u32 reserved:25; |
| } bits; |
| u32 word; |
| } enable; |
| u8 instruction; |
| u8 mode; |
| u8 num_mode_cycles; |
| u8 num_dummy_cycles; |
| u32 address; |
| |
| size_t buf_len; |
| const void *tx_buf; |
| void *rx_buf; |
| }; |
| |
| /* Register access functions */ |
| static inline u32 qspi_readl(struct atmel_qspi *aq, u32 reg) |
| { |
| return readl_relaxed(aq->regs + reg); |
| } |
| |
| static inline void qspi_writel(struct atmel_qspi *aq, u32 reg, u32 value) |
| { |
| writel_relaxed(value, aq->regs + reg); |
| } |
| |
| static int atmel_qspi_run_transfer(struct atmel_qspi *aq, |
| const struct atmel_qspi_command *cmd) |
| { |
| void __iomem *ahb_mem; |
| |
| /* Then fallback to a PIO transfer (memcpy() DOES NOT work!) */ |
| ahb_mem = aq->mem; |
| if (cmd->enable.bits.address) |
| ahb_mem += cmd->address; |
| if (cmd->tx_buf) |
| _memcpy_toio(ahb_mem, cmd->tx_buf, cmd->buf_len); |
| else |
| _memcpy_fromio(cmd->rx_buf, ahb_mem, cmd->buf_len); |
| |
| return 0; |
| } |
| |
| #ifdef DEBUG |
| static void atmel_qspi_debug_command(struct atmel_qspi *aq, |
| const struct atmel_qspi_command *cmd, |
| u32 ifr) |
| { |
| u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE]; |
| size_t len = 0; |
| int i; |
| |
| if (cmd->enable.bits.instruction) |
| cmd_buf[len++] = cmd->instruction; |
| |
| for (i = cmd->enable.bits.address-1; i >= 0; --i) |
| cmd_buf[len++] = (cmd->address >> (i << 3)) & 0xff; |
| |
| if (cmd->enable.bits.mode) |
| cmd_buf[len++] = cmd->mode; |
| |
| if (cmd->enable.bits.dummy) { |
| int num = cmd->num_dummy_cycles; |
| |
| switch (ifr & QSPI_IFR_WIDTH_MASK) { |
| case QSPI_IFR_WIDTH_SINGLE_BIT_SPI: |
| case QSPI_IFR_WIDTH_DUAL_OUTPUT: |
| case QSPI_IFR_WIDTH_QUAD_OUTPUT: |
| num >>= 3; |
| break; |
| case QSPI_IFR_WIDTH_DUAL_IO: |
| case QSPI_IFR_WIDTH_DUAL_CMD: |
| num >>= 2; |
| break; |
| case QSPI_IFR_WIDTH_QUAD_IO: |
| case QSPI_IFR_WIDTH_QUAD_CMD: |
| num >>= 1; |
| break; |
| default: |
| return; |
| } |
| |
| for (i = 0; i < num; ++i) |
| cmd_buf[len++] = 0; |
| } |
| |
| /* Dump the SPI command */ |
| print_hex_dump(KERN_DEBUG, "qspi cmd: ", DUMP_PREFIX_NONE, |
| 32, 1, cmd_buf, len, false); |
| |
| #ifdef VERBOSE_DEBUG |
| /* If verbose debug is enabled, also dump the TX data */ |
| if (cmd->enable.bits.data && cmd->tx_buf) |
| print_hex_dump(KERN_DEBUG, "qspi tx : ", DUMP_PREFIX_NONE, |
| 32, 1, cmd->tx_buf, cmd->buf_len, false); |
| #endif |
| } |
| #else |
| #define atmel_qspi_debug_command(aq, cmd, ifr) |
| #endif |
| |
| static int atmel_qspi_run_command(struct atmel_qspi *aq, |
| const struct atmel_qspi_command *cmd, |
| u32 ifr_tfrtyp, u32 ifr_width) |
| { |
| u32 iar, icr, ifr, sr; |
| int err = 0; |
| |
| iar = 0; |
| icr = 0; |
| ifr = ifr_tfrtyp | ifr_width; |
| |
| /* Compute instruction parameters */ |
| if (cmd->enable.bits.instruction) { |
| icr |= QSPI_ICR_INST(cmd->instruction); |
| ifr |= QSPI_IFR_INSTEN; |
| } |
| |
| /* Compute address parameters */ |
| switch (cmd->enable.bits.address) { |
| case 4: |
| ifr |= QSPI_IFR_ADDRL; |
| /* fall through to the 24bit (3 byte) address case. */ |
| case 3: |
| iar = (cmd->enable.bits.data) ? 0 : cmd->address; |
| ifr |= QSPI_IFR_ADDREN; |
| break; |
| case 0: |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| /* Compute option parameters */ |
| if (cmd->enable.bits.mode && cmd->num_mode_cycles) { |
| u32 mode_cycle_bits, mode_bits; |
| |
| icr |= QSPI_ICR_OPT(cmd->mode); |
| ifr |= QSPI_IFR_OPTEN; |
| |
| switch (ifr & QSPI_IFR_WIDTH_MASK) { |
| case QSPI_IFR_WIDTH_SINGLE_BIT_SPI: |
| case QSPI_IFR_WIDTH_DUAL_OUTPUT: |
| case QSPI_IFR_WIDTH_QUAD_OUTPUT: |
| mode_cycle_bits = 1; |
| break; |
| case QSPI_IFR_WIDTH_DUAL_IO: |
| case QSPI_IFR_WIDTH_DUAL_CMD: |
| mode_cycle_bits = 2; |
| break; |
| case QSPI_IFR_WIDTH_QUAD_IO: |
| case QSPI_IFR_WIDTH_QUAD_CMD: |
| mode_cycle_bits = 4; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| mode_bits = cmd->num_mode_cycles * mode_cycle_bits; |
| switch (mode_bits) { |
| case 1: |
| ifr |= QSPI_IFR_OPTL_1BIT; |
| break; |
| |
| case 2: |
| ifr |= QSPI_IFR_OPTL_2BIT; |
| break; |
| |
| case 4: |
| ifr |= QSPI_IFR_OPTL_4BIT; |
| break; |
| |
| case 8: |
| ifr |= QSPI_IFR_OPTL_8BIT; |
| break; |
| |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| /* Set number of dummy cycles */ |
| if (cmd->enable.bits.dummy) |
| ifr |= QSPI_IFR_NBDUM(cmd->num_dummy_cycles); |
| |
| /* Set data enable */ |
| if (cmd->enable.bits.data) { |
| ifr |= QSPI_IFR_DATAEN; |
| |
| /* Special case for Continuous Read Mode */ |
| if (!cmd->tx_buf && !cmd->rx_buf) |
| ifr |= QSPI_IFR_CRM; |
| } |
| |
| /* Clear pending interrupts */ |
| (void)qspi_readl(aq, QSPI_SR); |
| |
| /* Set QSPI Instruction Frame registers */ |
| atmel_qspi_debug_command(aq, cmd, ifr); |
| qspi_writel(aq, QSPI_IAR, iar); |
| qspi_writel(aq, QSPI_ICR, icr); |
| qspi_writel(aq, QSPI_IFR, ifr); |
| |
| /* Skip to the final steps if there is no data */ |
| if (!cmd->enable.bits.data) |
| goto no_data; |
| |
| /* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */ |
| (void)qspi_readl(aq, QSPI_IFR); |
| |
| /* Stop here for continuous read */ |
| if (!cmd->tx_buf && !cmd->rx_buf) |
| return 0; |
| /* Send/Receive data */ |
| err = atmel_qspi_run_transfer(aq, cmd); |
| |
| /* Release the chip-select */ |
| qspi_writel(aq, QSPI_CR, QSPI_CR_LASTXFER); |
| |
| if (err) |
| return err; |
| |
| #if defined(DEBUG) && defined(VERBOSE_DEBUG) |
| /* |
| * If verbose debug is enabled, also dump the RX data in addition to |
| * the SPI command previously dumped by atmel_qspi_debug_command() |
| */ |
| if (cmd->rx_buf) |
| print_hex_dump(KERN_DEBUG, "qspi rx : ", DUMP_PREFIX_NONE, |
| 32, 1, cmd->rx_buf, cmd->buf_len, false); |
| #endif |
| no_data: |
| /* Poll INSTRuction End status */ |
| sr = qspi_readl(aq, QSPI_SR); |
| if ((sr & QSPI_SR_CMD_COMPLETED) == QSPI_SR_CMD_COMPLETED) |
| return err; |
| |
| /* Wait for INSTRuction End interrupt */ |
| reinit_completion(&aq->cmd_completion); |
| aq->pending = sr & QSPI_SR_CMD_COMPLETED; |
| qspi_writel(aq, QSPI_IER, QSPI_SR_CMD_COMPLETED); |
| if (!wait_for_completion_timeout(&aq->cmd_completion, |
| msecs_to_jiffies(1000))) |
| err = -ETIMEDOUT; |
| qspi_writel(aq, QSPI_IDR, QSPI_SR_CMD_COMPLETED); |
| |
| return err; |
| } |
| |
| static int atmel_qspi_read_reg(struct spi_nor *nor, u8 opcode, |
| u8 *buf, int len) |
| { |
| struct atmel_qspi *aq = nor->priv; |
| struct atmel_qspi_command cmd; |
| |
| memset(&cmd, 0, sizeof(cmd)); |
| cmd.enable.bits.instruction = 1; |
| cmd.enable.bits.data = 1; |
| cmd.instruction = opcode; |
| cmd.rx_buf = buf; |
| cmd.buf_len = len; |
| return atmel_qspi_run_command(aq, &cmd, QSPI_IFR_TFRTYP_TRSFR_READ, |
| QSPI_IFR_WIDTH_SINGLE_BIT_SPI); |
| } |
| |
| static int atmel_qspi_write_reg(struct spi_nor *nor, u8 opcode, |
| u8 *buf, int len) |
| { |
| struct atmel_qspi *aq = nor->priv; |
| struct atmel_qspi_command cmd; |
| |
| memset(&cmd, 0, sizeof(cmd)); |
| cmd.enable.bits.instruction = 1; |
| cmd.enable.bits.data = (buf != NULL && len > 0); |
| cmd.instruction = opcode; |
| cmd.tx_buf = buf; |
| cmd.buf_len = len; |
| return atmel_qspi_run_command(aq, &cmd, QSPI_IFR_TFRTYP_TRSFR_WRITE, |
| QSPI_IFR_WIDTH_SINGLE_BIT_SPI); |
| } |
| |
| static ssize_t atmel_qspi_write(struct spi_nor *nor, loff_t to, size_t len, |
| const u_char *write_buf) |
| { |
| struct atmel_qspi *aq = nor->priv; |
| struct atmel_qspi_command cmd; |
| ssize_t ret; |
| |
| memset(&cmd, 0, sizeof(cmd)); |
| cmd.enable.bits.instruction = 1; |
| cmd.enable.bits.address = nor->addr_width; |
| cmd.enable.bits.data = 1; |
| cmd.instruction = nor->program_opcode; |
| cmd.address = (u32)to; |
| cmd.tx_buf = write_buf; |
| cmd.buf_len = len; |
| ret = atmel_qspi_run_command(aq, &cmd, QSPI_IFR_TFRTYP_TRSFR_WRITE_MEM, |
| QSPI_IFR_WIDTH_SINGLE_BIT_SPI); |
| return (ret < 0) ? ret : len; |
| } |
| |
| static int atmel_qspi_erase(struct spi_nor *nor, loff_t offs) |
| { |
| struct atmel_qspi *aq = nor->priv; |
| struct atmel_qspi_command cmd; |
| |
| memset(&cmd, 0, sizeof(cmd)); |
| cmd.enable.bits.instruction = 1; |
| cmd.enable.bits.address = nor->addr_width; |
| cmd.instruction = nor->erase_opcode; |
| cmd.address = (u32)offs; |
| return atmel_qspi_run_command(aq, &cmd, QSPI_IFR_TFRTYP_TRSFR_WRITE, |
| QSPI_IFR_WIDTH_SINGLE_BIT_SPI); |
| } |
| |
| static ssize_t atmel_qspi_read(struct spi_nor *nor, loff_t from, size_t len, |
| u_char *read_buf) |
| { |
| struct atmel_qspi *aq = nor->priv; |
| struct atmel_qspi_command cmd; |
| u8 num_mode_cycles, num_dummy_cycles; |
| u32 ifr_width; |
| ssize_t ret; |
| |
| switch (nor->flash_read) { |
| case SPI_NOR_NORMAL: |
| case SPI_NOR_FAST: |
| ifr_width = QSPI_IFR_WIDTH_SINGLE_BIT_SPI; |
| break; |
| |
| case SPI_NOR_DUAL: |
| ifr_width = QSPI_IFR_WIDTH_DUAL_OUTPUT; |
| break; |
| |
| case SPI_NOR_QUAD: |
| ifr_width = QSPI_IFR_WIDTH_QUAD_OUTPUT; |
| break; |
| |
| default: |
| return -EINVAL; |
| } |
| |
| if (nor->read_dummy >= 2) { |
| num_mode_cycles = 2; |
| num_dummy_cycles = nor->read_dummy - 2; |
| } else { |
| num_mode_cycles = nor->read_dummy; |
| num_dummy_cycles = 0; |
| } |
| |
| memset(&cmd, 0, sizeof(cmd)); |
| cmd.enable.bits.instruction = 1; |
| cmd.enable.bits.address = nor->addr_width; |
| cmd.enable.bits.mode = (num_mode_cycles > 0); |
| cmd.enable.bits.dummy = (num_dummy_cycles > 0); |
| cmd.enable.bits.data = 1; |
| cmd.instruction = nor->read_opcode; |
| cmd.address = (u32)from; |
| cmd.mode = 0xff; /* This value prevents from entering the 0-4-4 mode */ |
| cmd.num_mode_cycles = num_mode_cycles; |
| cmd.num_dummy_cycles = num_dummy_cycles; |
| cmd.rx_buf = read_buf; |
| cmd.buf_len = len; |
| ret = atmel_qspi_run_command(aq, &cmd, QSPI_IFR_TFRTYP_TRSFR_READ_MEM, |
| ifr_width); |
| return (ret < 0) ? ret : len; |
| } |
| |
| static int atmel_qspi_init(struct atmel_qspi *aq) |
| { |
| unsigned long src_rate; |
| u32 mr, scr, scbr; |
| |
| /* Reset the QSPI controller */ |
| qspi_writel(aq, QSPI_CR, QSPI_CR_SWRST); |
| |
| /* Set the QSPI controller in Serial Memory Mode */ |
| mr = QSPI_MR_NBBITS(8) | QSPI_MR_SSM; |
| qspi_writel(aq, QSPI_MR, mr); |
| |
| src_rate = clk_get_rate(aq->clk); |
| if (!src_rate) |
| return -EINVAL; |
| |
| /* Compute the QSPI baudrate */ |
| scbr = DIV_ROUND_UP(src_rate, aq->clk_rate); |
| if (scbr > 0) |
| scbr--; |
| scr = QSPI_SCR_SCBR(scbr); |
| qspi_writel(aq, QSPI_SCR, scr); |
| |
| /* Enable the QSPI controller */ |
| qspi_writel(aq, QSPI_CR, QSPI_CR_QSPIEN); |
| |
| return 0; |
| } |
| |
| static irqreturn_t atmel_qspi_interrupt(int irq, void *dev_id) |
| { |
| struct atmel_qspi *aq = (struct atmel_qspi *)dev_id; |
| u32 status, mask, pending; |
| |
| status = qspi_readl(aq, QSPI_SR); |
| mask = qspi_readl(aq, QSPI_IMR); |
| pending = status & mask; |
| |
| if (!pending) |
| return IRQ_NONE; |
| |
| aq->pending |= pending; |
| if ((aq->pending & QSPI_SR_CMD_COMPLETED) == QSPI_SR_CMD_COMPLETED) |
| complete(&aq->cmd_completion); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int atmel_qspi_probe(struct platform_device *pdev) |
| { |
| struct device_node *child, *np = pdev->dev.of_node; |
| struct atmel_qspi *aq; |
| struct resource *res; |
| struct spi_nor *nor; |
| struct mtd_info *mtd; |
| int irq, err = 0; |
| |
| if (of_get_child_count(np) != 1) |
| return -ENODEV; |
| child = of_get_next_child(np, NULL); |
| |
| aq = devm_kzalloc(&pdev->dev, sizeof(*aq), GFP_KERNEL); |
| if (!aq) { |
| err = -ENOMEM; |
| goto exit; |
| } |
| |
| platform_set_drvdata(pdev, aq); |
| init_completion(&aq->cmd_completion); |
| aq->pdev = pdev; |
| |
| /* Map the registers */ |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qspi_base"); |
| aq->regs = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(aq->regs)) { |
| dev_err(&pdev->dev, "missing registers\n"); |
| err = PTR_ERR(aq->regs); |
| goto exit; |
| } |
| |
| /* Map the AHB memory */ |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qspi_mmap"); |
| aq->mem = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(aq->mem)) { |
| dev_err(&pdev->dev, "missing AHB memory\n"); |
| err = PTR_ERR(aq->mem); |
| goto exit; |
| } |
| |
| /* Get the peripheral clock */ |
| aq->clk = devm_clk_get(&pdev->dev, NULL); |
| if (IS_ERR(aq->clk)) { |
| dev_err(&pdev->dev, "missing peripheral clock\n"); |
| err = PTR_ERR(aq->clk); |
| goto exit; |
| } |
| |
| /* Enable the peripheral clock */ |
| err = clk_prepare_enable(aq->clk); |
| if (err) { |
| dev_err(&pdev->dev, "failed to enable the peripheral clock\n"); |
| goto exit; |
| } |
| |
| /* Request the IRQ */ |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) { |
| dev_err(&pdev->dev, "missing IRQ\n"); |
| err = irq; |
| goto disable_clk; |
| } |
| err = devm_request_irq(&pdev->dev, irq, atmel_qspi_interrupt, |
| 0, dev_name(&pdev->dev), aq); |
| if (err) |
| goto disable_clk; |
| |
| /* Setup the spi-nor */ |
| nor = &aq->nor; |
| mtd = &nor->mtd; |
| |
| nor->dev = &pdev->dev; |
| spi_nor_set_flash_node(nor, child); |
| nor->priv = aq; |
| mtd->priv = nor; |
| |
| nor->read_reg = atmel_qspi_read_reg; |
| nor->write_reg = atmel_qspi_write_reg; |
| nor->read = atmel_qspi_read; |
| nor->write = atmel_qspi_write; |
| nor->erase = atmel_qspi_erase; |
| |
| err = of_property_read_u32(child, "spi-max-frequency", &aq->clk_rate); |
| if (err < 0) |
| goto disable_clk; |
| |
| err = atmel_qspi_init(aq); |
| if (err) |
| goto disable_clk; |
| |
| err = spi_nor_scan(nor, NULL, SPI_NOR_QUAD); |
| if (err) |
| goto disable_clk; |
| |
| err = mtd_device_register(mtd, NULL, 0); |
| if (err) |
| goto disable_clk; |
| |
| of_node_put(child); |
| |
| return 0; |
| |
| disable_clk: |
| clk_disable_unprepare(aq->clk); |
| exit: |
| of_node_put(child); |
| |
| return err; |
| } |
| |
| static int atmel_qspi_remove(struct platform_device *pdev) |
| { |
| struct atmel_qspi *aq = platform_get_drvdata(pdev); |
| |
| mtd_device_unregister(&aq->nor.mtd); |
| qspi_writel(aq, QSPI_CR, QSPI_CR_QSPIDIS); |
| clk_disable_unprepare(aq->clk); |
| return 0; |
| } |
| |
| |
| static const struct of_device_id atmel_qspi_dt_ids[] = { |
| { .compatible = "atmel,sama5d2-qspi" }, |
| { /* sentinel */ } |
| }; |
| |
| MODULE_DEVICE_TABLE(of, atmel_qspi_dt_ids); |
| |
| static struct platform_driver atmel_qspi_driver = { |
| .driver = { |
| .name = "atmel_qspi", |
| .of_match_table = atmel_qspi_dt_ids, |
| }, |
| .probe = atmel_qspi_probe, |
| .remove = atmel_qspi_remove, |
| }; |
| module_platform_driver(atmel_qspi_driver); |
| |
| MODULE_AUTHOR("Cyrille Pitchen <cyrille.pitchen@atmel.com>"); |
| MODULE_DESCRIPTION("Atmel QSPI Controller driver"); |
| MODULE_LICENSE("GPL v2"); |