| /* |
| * Copyright (c) 2008, 2009 open80211s Ltd. |
| * Authors: Luis Carlos Cobo <luisca@cozybit.com> |
| * Javier Cardona <javier@cozybit.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <linux/slab.h> |
| #include <asm/unaligned.h> |
| #include "ieee80211_i.h" |
| #include "mesh.h" |
| |
| #define IEEE80211_MESH_PEER_INACTIVITY_LIMIT (1800 * HZ) |
| #define IEEE80211_MESH_HOUSEKEEPING_INTERVAL (60 * HZ) |
| #define IEEE80211_MESH_RANN_INTERVAL (1 * HZ) |
| |
| #define MESHCONF_CAPAB_ACCEPT_PLINKS 0x01 |
| #define MESHCONF_CAPAB_FORWARDING 0x08 |
| |
| #define TMR_RUNNING_HK 0 |
| #define TMR_RUNNING_MP 1 |
| #define TMR_RUNNING_MPR 2 |
| |
| int mesh_allocated; |
| static struct kmem_cache *rm_cache; |
| |
| void ieee80211s_init(void) |
| { |
| mesh_pathtbl_init(); |
| mesh_allocated = 1; |
| rm_cache = kmem_cache_create("mesh_rmc", sizeof(struct rmc_entry), |
| 0, 0, NULL); |
| } |
| |
| void ieee80211s_stop(void) |
| { |
| mesh_pathtbl_unregister(); |
| kmem_cache_destroy(rm_cache); |
| } |
| |
| static void ieee80211_mesh_housekeeping_timer(unsigned long data) |
| { |
| struct ieee80211_sub_if_data *sdata = (void *) data; |
| struct ieee80211_local *local = sdata->local; |
| struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh; |
| |
| set_bit(MESH_WORK_HOUSEKEEPING, &ifmsh->wrkq_flags); |
| |
| if (local->quiescing) { |
| set_bit(TMR_RUNNING_HK, &ifmsh->timers_running); |
| return; |
| } |
| |
| ieee80211_queue_work(&local->hw, &sdata->work); |
| } |
| |
| /** |
| * mesh_matches_local - check if the config of a mesh point matches ours |
| * |
| * @ie: information elements of a management frame from the mesh peer |
| * @sdata: local mesh subif |
| * |
| * This function checks if the mesh configuration of a mesh point matches the |
| * local mesh configuration, i.e. if both nodes belong to the same mesh network. |
| */ |
| bool mesh_matches_local(struct ieee802_11_elems *ie, struct ieee80211_sub_if_data *sdata) |
| { |
| struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh; |
| |
| /* |
| * As support for each feature is added, check for matching |
| * - On mesh config capabilities |
| * - Power Save Support En |
| * - Sync support enabled |
| * - Sync support active |
| * - Sync support required from peer |
| * - MDA enabled |
| * - Power management control on fc |
| */ |
| if (ifmsh->mesh_id_len == ie->mesh_id_len && |
| memcmp(ifmsh->mesh_id, ie->mesh_id, ie->mesh_id_len) == 0 && |
| (ifmsh->mesh_pp_id == ie->mesh_config->meshconf_psel) && |
| (ifmsh->mesh_pm_id == ie->mesh_config->meshconf_pmetric) && |
| (ifmsh->mesh_cc_id == ie->mesh_config->meshconf_congest) && |
| (ifmsh->mesh_sp_id == ie->mesh_config->meshconf_synch) && |
| (ifmsh->mesh_auth_id == ie->mesh_config->meshconf_auth)) |
| return true; |
| |
| return false; |
| } |
| |
| /** |
| * mesh_peer_accepts_plinks - check if an mp is willing to establish peer links |
| * |
| * @ie: information elements of a management frame from the mesh peer |
| */ |
| bool mesh_peer_accepts_plinks(struct ieee802_11_elems *ie) |
| { |
| return (ie->mesh_config->meshconf_cap & |
| MESHCONF_CAPAB_ACCEPT_PLINKS) != 0; |
| } |
| |
| /** |
| * mesh_accept_plinks_update: update accepting_plink in local mesh beacons |
| * |
| * @sdata: mesh interface in which mesh beacons are going to be updated |
| */ |
| void mesh_accept_plinks_update(struct ieee80211_sub_if_data *sdata) |
| { |
| bool free_plinks; |
| |
| /* In case mesh_plink_free_count > 0 and mesh_plinktbl_capacity == 0, |
| * the mesh interface might be able to establish plinks with peers that |
| * are already on the table but are not on PLINK_ESTAB state. However, |
| * in general the mesh interface is not accepting peer link requests |
| * from new peers, and that must be reflected in the beacon |
| */ |
| free_plinks = mesh_plink_availables(sdata); |
| |
| if (free_plinks != sdata->u.mesh.accepting_plinks) |
| ieee80211_mesh_housekeeping_timer((unsigned long) sdata); |
| } |
| |
| int mesh_rmc_init(struct ieee80211_sub_if_data *sdata) |
| { |
| int i; |
| |
| sdata->u.mesh.rmc = kmalloc(sizeof(struct mesh_rmc), GFP_KERNEL); |
| if (!sdata->u.mesh.rmc) |
| return -ENOMEM; |
| sdata->u.mesh.rmc->idx_mask = RMC_BUCKETS - 1; |
| for (i = 0; i < RMC_BUCKETS; i++) |
| INIT_LIST_HEAD(&sdata->u.mesh.rmc->bucket[i].list); |
| return 0; |
| } |
| |
| void mesh_rmc_free(struct ieee80211_sub_if_data *sdata) |
| { |
| struct mesh_rmc *rmc = sdata->u.mesh.rmc; |
| struct rmc_entry *p, *n; |
| int i; |
| |
| if (!sdata->u.mesh.rmc) |
| return; |
| |
| for (i = 0; i < RMC_BUCKETS; i++) |
| list_for_each_entry_safe(p, n, &rmc->bucket[i].list, list) { |
| list_del(&p->list); |
| kmem_cache_free(rm_cache, p); |
| } |
| |
| kfree(rmc); |
| sdata->u.mesh.rmc = NULL; |
| } |
| |
| /** |
| * mesh_rmc_check - Check frame in recent multicast cache and add if absent. |
| * |
| * @sa: source address |
| * @mesh_hdr: mesh_header |
| * |
| * Returns: 0 if the frame is not in the cache, nonzero otherwise. |
| * |
| * Checks using the source address and the mesh sequence number if we have |
| * received this frame lately. If the frame is not in the cache, it is added to |
| * it. |
| */ |
| int mesh_rmc_check(u8 *sa, struct ieee80211s_hdr *mesh_hdr, |
| struct ieee80211_sub_if_data *sdata) |
| { |
| struct mesh_rmc *rmc = sdata->u.mesh.rmc; |
| u32 seqnum = 0; |
| int entries = 0; |
| u8 idx; |
| struct rmc_entry *p, *n; |
| |
| /* Don't care about endianness since only match matters */ |
| memcpy(&seqnum, &mesh_hdr->seqnum, sizeof(mesh_hdr->seqnum)); |
| idx = le32_to_cpu(mesh_hdr->seqnum) & rmc->idx_mask; |
| list_for_each_entry_safe(p, n, &rmc->bucket[idx].list, list) { |
| ++entries; |
| if (time_after(jiffies, p->exp_time) || |
| (entries == RMC_QUEUE_MAX_LEN)) { |
| list_del(&p->list); |
| kmem_cache_free(rm_cache, p); |
| --entries; |
| } else if ((seqnum == p->seqnum) && |
| (memcmp(sa, p->sa, ETH_ALEN) == 0)) |
| return -1; |
| } |
| |
| p = kmem_cache_alloc(rm_cache, GFP_ATOMIC); |
| if (!p) { |
| printk(KERN_DEBUG "o11s: could not allocate RMC entry\n"); |
| return 0; |
| } |
| p->seqnum = seqnum; |
| p->exp_time = jiffies + RMC_TIMEOUT; |
| memcpy(p->sa, sa, ETH_ALEN); |
| list_add(&p->list, &rmc->bucket[idx].list); |
| return 0; |
| } |
| |
| void mesh_mgmt_ies_add(struct sk_buff *skb, struct ieee80211_sub_if_data *sdata) |
| { |
| struct ieee80211_local *local = sdata->local; |
| struct ieee80211_supported_band *sband; |
| u8 *pos; |
| int len, i, rate; |
| u8 neighbors; |
| |
| sband = local->hw.wiphy->bands[local->hw.conf.channel->band]; |
| len = sband->n_bitrates; |
| if (len > 8) |
| len = 8; |
| pos = skb_put(skb, len + 2); |
| *pos++ = WLAN_EID_SUPP_RATES; |
| *pos++ = len; |
| for (i = 0; i < len; i++) { |
| rate = sband->bitrates[i].bitrate; |
| *pos++ = (u8) (rate / 5); |
| } |
| |
| if (sband->n_bitrates > len) { |
| pos = skb_put(skb, sband->n_bitrates - len + 2); |
| *pos++ = WLAN_EID_EXT_SUPP_RATES; |
| *pos++ = sband->n_bitrates - len; |
| for (i = len; i < sband->n_bitrates; i++) { |
| rate = sband->bitrates[i].bitrate; |
| *pos++ = (u8) (rate / 5); |
| } |
| } |
| |
| if (sband->band == IEEE80211_BAND_2GHZ) { |
| pos = skb_put(skb, 2 + 1); |
| *pos++ = WLAN_EID_DS_PARAMS; |
| *pos++ = 1; |
| *pos++ = ieee80211_frequency_to_channel(local->hw.conf.channel->center_freq); |
| } |
| |
| pos = skb_put(skb, 2 + sdata->u.mesh.mesh_id_len); |
| *pos++ = WLAN_EID_MESH_ID; |
| *pos++ = sdata->u.mesh.mesh_id_len; |
| if (sdata->u.mesh.mesh_id_len) |
| memcpy(pos, sdata->u.mesh.mesh_id, sdata->u.mesh.mesh_id_len); |
| |
| pos = skb_put(skb, 2 + sizeof(struct ieee80211_meshconf_ie)); |
| *pos++ = WLAN_EID_MESH_CONFIG; |
| *pos++ = sizeof(struct ieee80211_meshconf_ie); |
| |
| /* Active path selection protocol ID */ |
| *pos++ = sdata->u.mesh.mesh_pp_id; |
| |
| /* Active path selection metric ID */ |
| *pos++ = sdata->u.mesh.mesh_pm_id; |
| |
| /* Congestion control mode identifier */ |
| *pos++ = sdata->u.mesh.mesh_cc_id; |
| |
| /* Synchronization protocol identifier */ |
| *pos++ = sdata->u.mesh.mesh_sp_id; |
| |
| /* Authentication Protocol identifier */ |
| *pos++ = sdata->u.mesh.mesh_auth_id; |
| |
| /* Mesh Formation Info - number of neighbors */ |
| neighbors = atomic_read(&sdata->u.mesh.mshstats.estab_plinks); |
| /* Number of neighbor mesh STAs or 15 whichever is smaller */ |
| neighbors = (neighbors > 15) ? 15 : neighbors; |
| *pos++ = neighbors << 1; |
| |
| /* Mesh capability */ |
| sdata->u.mesh.accepting_plinks = mesh_plink_availables(sdata); |
| *pos = MESHCONF_CAPAB_FORWARDING; |
| *pos++ |= sdata->u.mesh.accepting_plinks ? |
| MESHCONF_CAPAB_ACCEPT_PLINKS : 0x00; |
| *pos++ = 0x00; |
| |
| if (sdata->u.mesh.ie) { |
| int len = sdata->u.mesh.ie_len; |
| const u8 *data = sdata->u.mesh.ie; |
| if (skb_tailroom(skb) > len) |
| memcpy(skb_put(skb, len), data, len); |
| } |
| } |
| |
| |
| static void ieee80211_mesh_path_timer(unsigned long data) |
| { |
| struct ieee80211_sub_if_data *sdata = |
| (struct ieee80211_sub_if_data *) data; |
| struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh; |
| struct ieee80211_local *local = sdata->local; |
| |
| if (local->quiescing) { |
| set_bit(TMR_RUNNING_MP, &ifmsh->timers_running); |
| return; |
| } |
| |
| ieee80211_queue_work(&local->hw, &sdata->work); |
| } |
| |
| static void ieee80211_mesh_path_root_timer(unsigned long data) |
| { |
| struct ieee80211_sub_if_data *sdata = |
| (struct ieee80211_sub_if_data *) data; |
| struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh; |
| struct ieee80211_local *local = sdata->local; |
| |
| set_bit(MESH_WORK_ROOT, &ifmsh->wrkq_flags); |
| |
| if (local->quiescing) { |
| set_bit(TMR_RUNNING_MPR, &ifmsh->timers_running); |
| return; |
| } |
| |
| ieee80211_queue_work(&local->hw, &sdata->work); |
| } |
| |
| void ieee80211_mesh_root_setup(struct ieee80211_if_mesh *ifmsh) |
| { |
| if (ifmsh->mshcfg.dot11MeshHWMPRootMode) |
| set_bit(MESH_WORK_ROOT, &ifmsh->wrkq_flags); |
| else { |
| clear_bit(MESH_WORK_ROOT, &ifmsh->wrkq_flags); |
| /* stop running timer */ |
| del_timer_sync(&ifmsh->mesh_path_root_timer); |
| } |
| } |
| |
| /** |
| * ieee80211_fill_mesh_addresses - fill addresses of a locally originated mesh frame |
| * @hdr: 802.11 frame header |
| * @fc: frame control field |
| * @meshda: destination address in the mesh |
| * @meshsa: source address address in the mesh. Same as TA, as frame is |
| * locally originated. |
| * |
| * Return the length of the 802.11 (does not include a mesh control header) |
| */ |
| int ieee80211_fill_mesh_addresses(struct ieee80211_hdr *hdr, __le16 *fc, |
| const u8 *meshda, const u8 *meshsa) |
| { |
| if (is_multicast_ether_addr(meshda)) { |
| *fc |= cpu_to_le16(IEEE80211_FCTL_FROMDS); |
| /* DA TA SA */ |
| memcpy(hdr->addr1, meshda, ETH_ALEN); |
| memcpy(hdr->addr2, meshsa, ETH_ALEN); |
| memcpy(hdr->addr3, meshsa, ETH_ALEN); |
| return 24; |
| } else { |
| *fc |= cpu_to_le16(IEEE80211_FCTL_FROMDS | |
| IEEE80211_FCTL_TODS); |
| /* RA TA DA SA */ |
| memset(hdr->addr1, 0, ETH_ALEN); /* RA is resolved later */ |
| memcpy(hdr->addr2, meshsa, ETH_ALEN); |
| memcpy(hdr->addr3, meshda, ETH_ALEN); |
| memcpy(hdr->addr4, meshsa, ETH_ALEN); |
| return 30; |
| } |
| } |
| |
| /** |
| * ieee80211_new_mesh_header - create a new mesh header |
| * @meshhdr: uninitialized mesh header |
| * @sdata: mesh interface to be used |
| * @addr4or5: 1st address in the ae header, which may correspond to address 4 |
| * (if addr6 is NULL) or address 5 (if addr6 is present). It may |
| * be NULL. |
| * @addr6: 2nd address in the ae header, which corresponds to addr6 of the |
| * mesh frame |
| * |
| * Return the header length. |
| */ |
| int ieee80211_new_mesh_header(struct ieee80211s_hdr *meshhdr, |
| struct ieee80211_sub_if_data *sdata, char *addr4or5, |
| char *addr6) |
| { |
| int aelen = 0; |
| BUG_ON(!addr4or5 && addr6); |
| memset(meshhdr, 0, sizeof(*meshhdr)); |
| meshhdr->ttl = sdata->u.mesh.mshcfg.dot11MeshTTL; |
| put_unaligned(cpu_to_le32(sdata->u.mesh.mesh_seqnum), &meshhdr->seqnum); |
| sdata->u.mesh.mesh_seqnum++; |
| if (addr4or5 && !addr6) { |
| meshhdr->flags |= MESH_FLAGS_AE_A4; |
| aelen += ETH_ALEN; |
| memcpy(meshhdr->eaddr1, addr4or5, ETH_ALEN); |
| } else if (addr4or5 && addr6) { |
| meshhdr->flags |= MESH_FLAGS_AE_A5_A6; |
| aelen += 2 * ETH_ALEN; |
| memcpy(meshhdr->eaddr1, addr4or5, ETH_ALEN); |
| memcpy(meshhdr->eaddr2, addr6, ETH_ALEN); |
| } |
| return 6 + aelen; |
| } |
| |
| static void ieee80211_mesh_housekeeping(struct ieee80211_sub_if_data *sdata, |
| struct ieee80211_if_mesh *ifmsh) |
| { |
| bool free_plinks; |
| |
| #ifdef CONFIG_MAC80211_VERBOSE_DEBUG |
| printk(KERN_DEBUG "%s: running mesh housekeeping\n", |
| sdata->name); |
| #endif |
| |
| ieee80211_sta_expire(sdata, IEEE80211_MESH_PEER_INACTIVITY_LIMIT); |
| mesh_path_expire(sdata); |
| |
| free_plinks = mesh_plink_availables(sdata); |
| if (free_plinks != sdata->u.mesh.accepting_plinks) |
| ieee80211_bss_info_change_notify(sdata, BSS_CHANGED_BEACON); |
| |
| mod_timer(&ifmsh->housekeeping_timer, |
| round_jiffies(jiffies + IEEE80211_MESH_HOUSEKEEPING_INTERVAL)); |
| } |
| |
| static void ieee80211_mesh_rootpath(struct ieee80211_sub_if_data *sdata) |
| { |
| struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh; |
| |
| mesh_path_tx_root_frame(sdata); |
| mod_timer(&ifmsh->mesh_path_root_timer, |
| round_jiffies(jiffies + IEEE80211_MESH_RANN_INTERVAL)); |
| } |
| |
| #ifdef CONFIG_PM |
| void ieee80211_mesh_quiesce(struct ieee80211_sub_if_data *sdata) |
| { |
| struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh; |
| |
| /* use atomic bitops in case both timers fire at the same time */ |
| |
| if (del_timer_sync(&ifmsh->housekeeping_timer)) |
| set_bit(TMR_RUNNING_HK, &ifmsh->timers_running); |
| if (del_timer_sync(&ifmsh->mesh_path_timer)) |
| set_bit(TMR_RUNNING_MP, &ifmsh->timers_running); |
| if (del_timer_sync(&ifmsh->mesh_path_root_timer)) |
| set_bit(TMR_RUNNING_MPR, &ifmsh->timers_running); |
| } |
| |
| void ieee80211_mesh_restart(struct ieee80211_sub_if_data *sdata) |
| { |
| struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh; |
| |
| if (test_and_clear_bit(TMR_RUNNING_HK, &ifmsh->timers_running)) |
| add_timer(&ifmsh->housekeeping_timer); |
| if (test_and_clear_bit(TMR_RUNNING_MP, &ifmsh->timers_running)) |
| add_timer(&ifmsh->mesh_path_timer); |
| if (test_and_clear_bit(TMR_RUNNING_MPR, &ifmsh->timers_running)) |
| add_timer(&ifmsh->mesh_path_root_timer); |
| ieee80211_mesh_root_setup(ifmsh); |
| } |
| #endif |
| |
| void ieee80211_start_mesh(struct ieee80211_sub_if_data *sdata) |
| { |
| struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh; |
| struct ieee80211_local *local = sdata->local; |
| |
| local->fif_other_bss++; |
| /* mesh ifaces must set allmulti to forward mcast traffic */ |
| atomic_inc(&local->iff_allmultis); |
| ieee80211_configure_filter(local); |
| |
| ifmsh->mesh_cc_id = 0; /* Disabled */ |
| ifmsh->mesh_sp_id = 0; /* Neighbor Offset */ |
| ifmsh->mesh_auth_id = 0; /* Disabled */ |
| set_bit(MESH_WORK_HOUSEKEEPING, &ifmsh->wrkq_flags); |
| ieee80211_mesh_root_setup(ifmsh); |
| ieee80211_queue_work(&local->hw, &sdata->work); |
| sdata->vif.bss_conf.beacon_int = MESH_DEFAULT_BEACON_INTERVAL; |
| ieee80211_bss_info_change_notify(sdata, BSS_CHANGED_BEACON | |
| BSS_CHANGED_BEACON_ENABLED | |
| BSS_CHANGED_BEACON_INT); |
| } |
| |
| void ieee80211_stop_mesh(struct ieee80211_sub_if_data *sdata) |
| { |
| struct ieee80211_local *local = sdata->local; |
| struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh; |
| |
| ifmsh->mesh_id_len = 0; |
| ieee80211_bss_info_change_notify(sdata, BSS_CHANGED_BEACON_ENABLED); |
| sta_info_flush(local, NULL); |
| |
| del_timer_sync(&sdata->u.mesh.housekeeping_timer); |
| del_timer_sync(&sdata->u.mesh.mesh_path_root_timer); |
| /* |
| * If the timer fired while we waited for it, it will have |
| * requeued the work. Now the work will be running again |
| * but will not rearm the timer again because it checks |
| * whether the interface is running, which, at this point, |
| * it no longer is. |
| */ |
| cancel_work_sync(&sdata->work); |
| |
| local->fif_other_bss--; |
| atomic_dec(&local->iff_allmultis); |
| ieee80211_configure_filter(local); |
| } |
| |
| static void ieee80211_mesh_rx_bcn_presp(struct ieee80211_sub_if_data *sdata, |
| u16 stype, |
| struct ieee80211_mgmt *mgmt, |
| size_t len, |
| struct ieee80211_rx_status *rx_status) |
| { |
| struct ieee80211_local *local = sdata->local; |
| struct ieee802_11_elems elems; |
| struct ieee80211_channel *channel; |
| u32 supp_rates = 0; |
| size_t baselen; |
| int freq; |
| enum ieee80211_band band = rx_status->band; |
| |
| /* ignore ProbeResp to foreign address */ |
| if (stype == IEEE80211_STYPE_PROBE_RESP && |
| compare_ether_addr(mgmt->da, sdata->vif.addr)) |
| return; |
| |
| baselen = (u8 *) mgmt->u.probe_resp.variable - (u8 *) mgmt; |
| if (baselen > len) |
| return; |
| |
| ieee802_11_parse_elems(mgmt->u.probe_resp.variable, len - baselen, |
| &elems); |
| |
| /* ignore beacons from secure mesh peers if our security is off */ |
| if (elems.rsn_len && sdata->u.mesh.security == IEEE80211_MESH_SEC_NONE) |
| return; |
| |
| if (elems.ds_params && elems.ds_params_len == 1) |
| freq = ieee80211_channel_to_frequency(elems.ds_params[0], band); |
| else |
| freq = rx_status->freq; |
| |
| channel = ieee80211_get_channel(local->hw.wiphy, freq); |
| |
| if (!channel || channel->flags & IEEE80211_CHAN_DISABLED) |
| return; |
| |
| if (elems.mesh_id && elems.mesh_config && |
| mesh_matches_local(&elems, sdata)) { |
| supp_rates = ieee80211_sta_get_rates(local, &elems, band); |
| mesh_neighbour_update(mgmt->sa, supp_rates, sdata, &elems); |
| } |
| } |
| |
| static void ieee80211_mesh_rx_mgmt_action(struct ieee80211_sub_if_data *sdata, |
| struct ieee80211_mgmt *mgmt, |
| size_t len, |
| struct ieee80211_rx_status *rx_status) |
| { |
| switch (mgmt->u.action.category) { |
| case WLAN_CATEGORY_MESH_ACTION: |
| mesh_rx_plink_frame(sdata, mgmt, len, rx_status); |
| break; |
| case WLAN_CATEGORY_MESH_PATH_SEL: |
| mesh_rx_path_sel_frame(sdata, mgmt, len); |
| break; |
| } |
| } |
| |
| void ieee80211_mesh_rx_queued_mgmt(struct ieee80211_sub_if_data *sdata, |
| struct sk_buff *skb) |
| { |
| struct ieee80211_rx_status *rx_status; |
| struct ieee80211_mgmt *mgmt; |
| u16 stype; |
| |
| rx_status = IEEE80211_SKB_RXCB(skb); |
| mgmt = (struct ieee80211_mgmt *) skb->data; |
| stype = le16_to_cpu(mgmt->frame_control) & IEEE80211_FCTL_STYPE; |
| |
| switch (stype) { |
| case IEEE80211_STYPE_PROBE_RESP: |
| case IEEE80211_STYPE_BEACON: |
| ieee80211_mesh_rx_bcn_presp(sdata, stype, mgmt, skb->len, |
| rx_status); |
| break; |
| case IEEE80211_STYPE_ACTION: |
| ieee80211_mesh_rx_mgmt_action(sdata, mgmt, skb->len, rx_status); |
| break; |
| } |
| } |
| |
| void ieee80211_mesh_work(struct ieee80211_sub_if_data *sdata) |
| { |
| struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh; |
| |
| if (ifmsh->preq_queue_len && |
| time_after(jiffies, |
| ifmsh->last_preq + msecs_to_jiffies(ifmsh->mshcfg.dot11MeshHWMPpreqMinInterval))) |
| mesh_path_start_discovery(sdata); |
| |
| if (test_and_clear_bit(MESH_WORK_GROW_MPATH_TABLE, &ifmsh->wrkq_flags)) |
| mesh_mpath_table_grow(); |
| |
| if (test_and_clear_bit(MESH_WORK_GROW_MPP_TABLE, &ifmsh->wrkq_flags)) |
| mesh_mpp_table_grow(); |
| |
| if (test_and_clear_bit(MESH_WORK_HOUSEKEEPING, &ifmsh->wrkq_flags)) |
| ieee80211_mesh_housekeeping(sdata, ifmsh); |
| |
| if (test_and_clear_bit(MESH_WORK_ROOT, &ifmsh->wrkq_flags)) |
| ieee80211_mesh_rootpath(sdata); |
| } |
| |
| void ieee80211_mesh_notify_scan_completed(struct ieee80211_local *local) |
| { |
| struct ieee80211_sub_if_data *sdata; |
| |
| rcu_read_lock(); |
| list_for_each_entry_rcu(sdata, &local->interfaces, list) |
| if (ieee80211_vif_is_mesh(&sdata->vif)) |
| ieee80211_queue_work(&local->hw, &sdata->work); |
| rcu_read_unlock(); |
| } |
| |
| void ieee80211_mesh_init_sdata(struct ieee80211_sub_if_data *sdata) |
| { |
| struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh; |
| |
| setup_timer(&ifmsh->housekeeping_timer, |
| ieee80211_mesh_housekeeping_timer, |
| (unsigned long) sdata); |
| |
| ifmsh->accepting_plinks = true; |
| ifmsh->preq_id = 0; |
| ifmsh->sn = 0; |
| atomic_set(&ifmsh->mpaths, 0); |
| mesh_rmc_init(sdata); |
| ifmsh->last_preq = jiffies; |
| /* Allocate all mesh structures when creating the first mesh interface. */ |
| if (!mesh_allocated) |
| ieee80211s_init(); |
| setup_timer(&ifmsh->mesh_path_timer, |
| ieee80211_mesh_path_timer, |
| (unsigned long) sdata); |
| setup_timer(&ifmsh->mesh_path_root_timer, |
| ieee80211_mesh_path_root_timer, |
| (unsigned long) sdata); |
| INIT_LIST_HEAD(&ifmsh->preq_queue.list); |
| spin_lock_init(&ifmsh->mesh_preq_queue_lock); |
| } |