[ARM] eseries: move LCD defs into machine files
This patch removes the seperate files used for the LCD definitions on
e-series and places the definitions into the machine specific files.
Signed-off-by: Ian Molton <spyro@f2s.com>
diff --git a/arch/arm/mach-pxa/e740.c b/arch/arm/mach-pxa/e740.c
index 560a8a2..ef0c3c8 100644
--- a/arch/arm/mach-pxa/e740.c
+++ b/arch/arm/mach-pxa/e740.c
@@ -12,6 +12,11 @@
#include <linux/kernel.h>
#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/fb.h>
+
+#include <video/w100fb.h>
#include <asm/setup.h>
#include <asm/mach/arch.h>
@@ -23,6 +28,80 @@
#include "generic.h"
#include "eseries.h"
+
+/* ------------------------ e740 video support --------------------------- */
+
+static struct w100_gen_regs e740_lcd_regs = {
+ .lcd_format = 0x00008023,
+ .lcdd_cntl1 = 0x0f000000,
+ .lcdd_cntl2 = 0x0003ffff,
+ .genlcd_cntl1 = 0x00ffff03,
+ .genlcd_cntl2 = 0x003c0f03,
+ .genlcd_cntl3 = 0x000143aa,
+};
+
+static struct w100_mode e740_lcd_mode = {
+ .xres = 240,
+ .yres = 320,
+ .left_margin = 20,
+ .right_margin = 28,
+ .upper_margin = 9,
+ .lower_margin = 8,
+ .crtc_ss = 0x80140013,
+ .crtc_ls = 0x81150110,
+ .crtc_gs = 0x80050005,
+ .crtc_vpos_gs = 0x000a0009,
+ .crtc_rev = 0x0040010a,
+ .crtc_dclk = 0xa906000a,
+ .crtc_gclk = 0x80050108,
+ .crtc_goe = 0x80050108,
+ .pll_freq = 57,
+ .pixclk_divider = 4,
+ .pixclk_divider_rotated = 4,
+ .pixclk_src = CLK_SRC_XTAL,
+ .sysclk_divider = 1,
+ .sysclk_src = CLK_SRC_PLL,
+ .crtc_ps1_active = 0x41060010,
+};
+
+static struct w100_gpio_regs e740_w100_gpio_info = {
+ .init_data1 = 0x21002103,
+ .gpio_dir1 = 0xffffdeff,
+ .gpio_oe1 = 0x03c00643,
+ .init_data2 = 0x003f003f,
+ .gpio_dir2 = 0xffffffff,
+ .gpio_oe2 = 0x000000ff,
+};
+
+static struct w100fb_mach_info e740_fb_info = {
+ .modelist = &e740_lcd_mode,
+ .num_modes = 1,
+ .regs = &e740_lcd_regs,
+ .gpio = &e740_w100_gpio_info,
+ .xtal_freq = 14318000,
+ .xtal_dbl = 1,
+};
+
+static struct resource e740_fb_resources[] = {
+ [0] = {
+ .start = 0x0c000000,
+ .end = 0x0cffffff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device e740_fb_device = {
+ .name = "w100fb",
+ .id = -1,
+ .dev = {
+ .platform_data = &e740_fb_info,
+ },
+ .num_resources = ARRAY_SIZE(e740_fb_resources),
+ .resource = e740_fb_resources,
+};
+
+/* --------------------------- MFP Pin config -------------------------- */
+
static unsigned long e740_pin_config[] __initdata = {
/* Chip selects */
GPIO15_nCS_1, /* CS1 - Flash */
@@ -62,9 +141,16 @@
GPIO0_GPIO | WAKEUP_ON_EDGE_RISE,
};
+/* ----------------------------------------------------------------------- */
+
+static struct platform_device *devices[] __initdata = {
+ &e740_fb_device,
+};
+
static void __init e740_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(e740_pin_config));
+ platform_add_devices(devices, ARRAY_SIZE(devices));
}
MACHINE_START(E740, "Toshiba e740")