mmc: sdhci-pci: add eMMC hardware reset support
Implement eMMC hardware reset for Medfield.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c
index 26c5286..3b30c51 100644
--- a/drivers/mmc/host/sdhci-pci.c
+++ b/drivers/mmc/host/sdhci-pci.c
@@ -21,6 +21,8 @@
#include <linux/mmc/host.h>
#include <linux/scatterlist.h>
#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/sfi.h>
#include "sdhci.h"
@@ -59,6 +61,7 @@
struct sdhci_host *host;
int pci_bar;
+ int rst_n_gpio;
};
struct sdhci_pci_chip {
@@ -163,12 +166,63 @@
return 0;
}
+/* Medfield eMMC hardware reset GPIOs */
+static int mfd_emmc0_rst_gpio = -EINVAL;
+static int mfd_emmc1_rst_gpio = -EINVAL;
+
+static int mfd_emmc_gpio_parse(struct sfi_table_header *table)
+{
+ struct sfi_table_simple *sb = (struct sfi_table_simple *)table;
+ struct sfi_gpio_table_entry *entry;
+ int i, num;
+
+ num = SFI_GET_NUM_ENTRIES(sb, struct sfi_gpio_table_entry);
+ entry = (struct sfi_gpio_table_entry *)sb->pentry;
+
+ for (i = 0; i < num; i++, entry++) {
+ if (!strncmp(entry->pin_name, "emmc0_rst", SFI_NAME_LEN))
+ mfd_emmc0_rst_gpio = entry->pin_no;
+ else if (!strncmp(entry->pin_name, "emmc1_rst", SFI_NAME_LEN))
+ mfd_emmc1_rst_gpio = entry->pin_no;
+ }
+
+ return 0;
+}
+
static int mfd_emmc_probe_slot(struct sdhci_pci_slot *slot)
{
+ const char *name = NULL;
+ int gpio = -EINVAL;
+
+ sfi_table_parse(SFI_SIG_GPIO, NULL, NULL, mfd_emmc_gpio_parse);
+
+ switch (slot->chip->pdev->device) {
+ case PCI_DEVICE_ID_INTEL_MFD_EMMC0:
+ gpio = mfd_emmc0_rst_gpio;
+ name = "eMMC0_reset";
+ break;
+ case PCI_DEVICE_ID_INTEL_MFD_EMMC1:
+ gpio = mfd_emmc1_rst_gpio;
+ name = "eMMC1_reset";
+ break;
+ }
+
+ if (!gpio_request(gpio, name)) {
+ gpio_direction_output(gpio, 1);
+ slot->rst_n_gpio = gpio;
+ slot->host->mmc->caps |= MMC_CAP_HW_RESET;
+ }
+
slot->host->mmc->caps |= MMC_CAP_8_BIT_DATA;
+
return 0;
}
+static void mfd_emmc_remove_slot(struct sdhci_pci_slot *slot, int dead)
+{
+ gpio_free(slot->rst_n_gpio);
+}
+
static const struct sdhci_pci_fixes sdhci_intel_mrst_hc0 = {
.quirks = SDHCI_QUIRK_BROKEN_ADMA | SDHCI_QUIRK_NO_HISPD_BIT,
.probe_slot = mrst_hc_probe_slot,
@@ -190,6 +244,7 @@
static const struct sdhci_pci_fixes sdhci_intel_mfd_emmc = {
.quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
.probe_slot = mfd_emmc_probe_slot,
+ .remove_slot = mfd_emmc_remove_slot,
};
/* O2Micro extra registers */
@@ -832,9 +887,25 @@
return 0;
}
+static void sdhci_pci_hw_reset(struct sdhci_host *host)
+{
+ struct sdhci_pci_slot *slot = sdhci_priv(host);
+ int rst_n_gpio = slot->rst_n_gpio;
+
+ if (!gpio_is_valid(rst_n_gpio))
+ return;
+ gpio_set_value_cansleep(rst_n_gpio, 0);
+ /* For eMMC, minimum is 1us but give it 10us for good measure */
+ udelay(10);
+ gpio_set_value_cansleep(rst_n_gpio, 1);
+ /* For eMMC, minimum is 200us but give it 300us for good measure */
+ usleep_range(300, 1000);
+}
+
static struct sdhci_ops sdhci_pci_ops = {
.enable_dma = sdhci_pci_enable_dma,
.platform_8bit_width = sdhci_pci_8bit_width,
+ .hw_reset = sdhci_pci_hw_reset,
};
/*****************************************************************************\
@@ -988,6 +1059,7 @@
slot->chip = chip;
slot->host = host;
slot->pci_bar = bar;
+ slot->rst_n_gpio = -EINVAL;
host->hw_name = "PCI";
host->ops = &sdhci_pci_ops;