diff --git a/arch/arm/mach-u300/i2c.c b/arch/arm/mach-u300/i2c.c
index cb04bd6..4227b15 100644
--- a/arch/arm/mach-u300/i2c.c
+++ b/arch/arm/mach-u300/i2c.c
@@ -9,7 +9,7 @@
  */
 #include <linux/kernel.h>
 #include <linux/i2c.h>
-#include <linux/mfd/abx500.h>
+#include <linux/mfd/ab3100.h>
 #include <linux/regulator/machine.h>
 #include <linux/amba/bus.h>
 #include <mach/irqs.h>
diff --git a/drivers/mfd/ab3100-core.c b/drivers/mfd/ab3100-core.c
index 01781ae..2b3dde5 100644
--- a/drivers/mfd/ab3100-core.c
+++ b/drivers/mfd/ab3100-core.c
@@ -21,6 +21,7 @@
 #include <linux/seq_file.h>
 #include <linux/uaccess.h>
 #include <linux/mfd/core.h>
+#include <linux/mfd/ab3100.h>
 #include <linux/mfd/abx500.h>
 
 /* These are the only registers inside AB3100 used in this main file */
diff --git a/drivers/regulator/ab3100.c b/drivers/regulator/ab3100.c
index 182b553..b6cde9c 100644
--- a/drivers/regulator/ab3100.c
+++ b/drivers/regulator/ab3100.c
@@ -15,6 +15,7 @@
 #include <linux/err.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
+#include <linux/mfd/ab3100.h>
 #include <linux/mfd/abx500.h>
 
 /* LDO registers and some handy masking definitions for AB3100 */
diff --git a/include/linux/mfd/ab3100.h b/include/linux/mfd/ab3100.h
new file mode 100644
index 0000000..afd3080
--- /dev/null
+++ b/include/linux/mfd/ab3100.h
@@ -0,0 +1,129 @@
+/*
+ * Copyright (C) 2007-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * AB3100 core access functions
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ *
+ */
+
+#include <linux/regulator/machine.h>
+
+struct device;
+
+#ifndef MFD_AB3100_H
+#define MFD_AB3100_H
+
+
+#define AB3100_P1A	0xc0
+#define AB3100_P1B	0xc1
+#define AB3100_P1C	0xc2
+#define AB3100_P1D	0xc3
+#define AB3100_P1E	0xc4
+#define AB3100_P1F	0xc5
+#define AB3100_P1G	0xc6
+#define AB3100_R2A	0xc7
+#define AB3100_R2B	0xc8
+
+/*
+ * AB3100, EVENTA1, A2 and A3 event register flags
+ * these are catenated into a single 32-bit flag in the code
+ * for event notification broadcasts.
+ */
+#define AB3100_EVENTA1_ONSWA				(0x01<<16)
+#define AB3100_EVENTA1_ONSWB				(0x02<<16)
+#define AB3100_EVENTA1_ONSWC				(0x04<<16)
+#define AB3100_EVENTA1_DCIO				(0x08<<16)
+#define AB3100_EVENTA1_OVER_TEMP			(0x10<<16)
+#define AB3100_EVENTA1_SIM_OFF				(0x20<<16)
+#define AB3100_EVENTA1_VBUS				(0x40<<16)
+#define AB3100_EVENTA1_VSET_USB				(0x80<<16)
+
+#define AB3100_EVENTA2_READY_TX				(0x01<<8)
+#define AB3100_EVENTA2_READY_RX				(0x02<<8)
+#define AB3100_EVENTA2_OVERRUN_ERROR			(0x04<<8)
+#define AB3100_EVENTA2_FRAMING_ERROR			(0x08<<8)
+#define AB3100_EVENTA2_CHARG_OVERCURRENT		(0x10<<8)
+#define AB3100_EVENTA2_MIDR				(0x20<<8)
+#define AB3100_EVENTA2_BATTERY_REM			(0x40<<8)
+#define AB3100_EVENTA2_ALARM				(0x80<<8)
+
+#define AB3100_EVENTA3_ADC_TRIG5			(0x01)
+#define AB3100_EVENTA3_ADC_TRIG4			(0x02)
+#define AB3100_EVENTA3_ADC_TRIG3			(0x04)
+#define AB3100_EVENTA3_ADC_TRIG2			(0x08)
+#define AB3100_EVENTA3_ADC_TRIGVBAT			(0x10)
+#define AB3100_EVENTA3_ADC_TRIGVTX			(0x20)
+#define AB3100_EVENTA3_ADC_TRIG1			(0x40)
+#define AB3100_EVENTA3_ADC_TRIG0			(0x80)
+
+/* AB3100, STR register flags */
+#define AB3100_STR_ONSWA				(0x01)
+#define AB3100_STR_ONSWB				(0x02)
+#define AB3100_STR_ONSWC				(0x04)
+#define AB3100_STR_DCIO					(0x08)
+#define AB3100_STR_BOOT_MODE				(0x10)
+#define AB3100_STR_SIM_OFF				(0x20)
+#define AB3100_STR_BATT_REMOVAL				(0x40)
+#define AB3100_STR_VBUS					(0x80)
+
+/*
+ * AB3100 contains 8 regulators, one external regulator controller
+ * and a buck converter, further the LDO E and buck converter can
+ * have separate settings if they are in sleep mode, this is
+ * modeled as a separate regulator.
+ */
+#define AB3100_NUM_REGULATORS				10
+
+/**
+ * struct ab3100
+ * @access_mutex: lock out concurrent accesses to the AB3100 registers
+ * @dev: pointer to the containing device
+ * @i2c_client: I2C client for this chip
+ * @testreg_client: secondary client for test registers
+ * @chip_name: name of this chip variant
+ * @chip_id: 8 bit chip ID for this chip variant
+ * @event_subscribers: event subscribers are listed here
+ * @startup_events: a copy of the first reading of the event registers
+ * @startup_events_read: whether the first events have been read
+ *
+ * This struct is PRIVATE and devices using it should NOT
+ * access ANY fields. It is used as a token for calling the
+ * AB3100 functions.
+ */
+struct ab3100 {
+	struct mutex access_mutex;
+	struct device *dev;
+	struct i2c_client *i2c_client;
+	struct i2c_client *testreg_client;
+	char chip_name[32];
+	u8 chip_id;
+	struct blocking_notifier_head event_subscribers;
+	u8 startup_events[3];
+	bool startup_events_read;
+};
+
+/**
+ * struct ab3100_platform_data
+ * Data supplied to initialize board connections to the AB3100
+ * @reg_constraints: regulator constraints for target board
+ *     the order of these constraints are: LDO A, C, D, E,
+ *     F, G, H, K, EXT and BUCK.
+ * @reg_initvals: initial values for the regulator registers
+ *     plus two sleep settings for LDO E and the BUCK converter.
+ *     exactly AB3100_NUM_REGULATORS+2 values must be sent in.
+ *     Order: LDO A, C, E, E sleep, F, G, H, K, EXT, BUCK,
+ *     BUCK sleep, LDO D. (LDO D need to be initialized last.)
+ * @external_voltage: voltage level of the external regulator.
+ */
+struct ab3100_platform_data {
+	struct regulator_init_data reg_constraints[AB3100_NUM_REGULATORS];
+	u8 reg_initvals[AB3100_NUM_REGULATORS+2];
+	int external_voltage;
+};
+
+int ab3100_event_register(struct ab3100 *ab3100,
+			  struct notifier_block *nb);
+int ab3100_event_unregister(struct ab3100 *ab3100,
+			    struct notifier_block *nb);
+
+#endif /*  MFD_AB3100_H */
diff --git a/include/linux/mfd/abx500.h b/include/linux/mfd/abx500.h
index 1318ca6..5d5298d 100644
--- a/include/linux/mfd/abx500.h
+++ b/include/linux/mfd/abx500.h
@@ -1,12 +1,9 @@
 /*
  * Copyright (C) 2007-2009 ST-Ericsson AB
  * License terms: GNU General Public License (GPL) version 2
- * AB3100 core access functions
- * Author: Linus Walleij <linus.walleij@stericsson.com>
  *
  * ABX500 core access functions.
- * The abx500 interface is used for the Analog Baseband chip
- * ab3100 and ab8500.
+ * The abx500 interface is used for the Analog Baseband chips.
  *
  * Author: Mattias Wallin <mattias.wallin@stericsson.com>
  * Author: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
@@ -21,118 +18,6 @@
 #ifndef MFD_ABX500_H
 #define MFD_ABX500_H
 
-#define AB3100_P1A	0xc0
-#define AB3100_P1B	0xc1
-#define AB3100_P1C	0xc2
-#define AB3100_P1D	0xc3
-#define AB3100_P1E	0xc4
-#define AB3100_P1F	0xc5
-#define AB3100_P1G	0xc6
-#define AB3100_R2A	0xc7
-#define AB3100_R2B	0xc8
-
-/*
- * AB3100, EVENTA1, A2 and A3 event register flags
- * these are catenated into a single 32-bit flag in the code
- * for event notification broadcasts.
- */
-#define AB3100_EVENTA1_ONSWA				(0x01<<16)
-#define AB3100_EVENTA1_ONSWB				(0x02<<16)
-#define AB3100_EVENTA1_ONSWC				(0x04<<16)
-#define AB3100_EVENTA1_DCIO				(0x08<<16)
-#define AB3100_EVENTA1_OVER_TEMP			(0x10<<16)
-#define AB3100_EVENTA1_SIM_OFF				(0x20<<16)
-#define AB3100_EVENTA1_VBUS				(0x40<<16)
-#define AB3100_EVENTA1_VSET_USB				(0x80<<16)
-
-#define AB3100_EVENTA2_READY_TX				(0x01<<8)
-#define AB3100_EVENTA2_READY_RX				(0x02<<8)
-#define AB3100_EVENTA2_OVERRUN_ERROR			(0x04<<8)
-#define AB3100_EVENTA2_FRAMING_ERROR			(0x08<<8)
-#define AB3100_EVENTA2_CHARG_OVERCURRENT		(0x10<<8)
-#define AB3100_EVENTA2_MIDR				(0x20<<8)
-#define AB3100_EVENTA2_BATTERY_REM			(0x40<<8)
-#define AB3100_EVENTA2_ALARM				(0x80<<8)
-
-#define AB3100_EVENTA3_ADC_TRIG5			(0x01)
-#define AB3100_EVENTA3_ADC_TRIG4			(0x02)
-#define AB3100_EVENTA3_ADC_TRIG3			(0x04)
-#define AB3100_EVENTA3_ADC_TRIG2			(0x08)
-#define AB3100_EVENTA3_ADC_TRIGVBAT			(0x10)
-#define AB3100_EVENTA3_ADC_TRIGVTX			(0x20)
-#define AB3100_EVENTA3_ADC_TRIG1			(0x40)
-#define AB3100_EVENTA3_ADC_TRIG0			(0x80)
-
-/* AB3100, STR register flags */
-#define AB3100_STR_ONSWA				(0x01)
-#define AB3100_STR_ONSWB				(0x02)
-#define AB3100_STR_ONSWC				(0x04)
-#define AB3100_STR_DCIO					(0x08)
-#define AB3100_STR_BOOT_MODE				(0x10)
-#define AB3100_STR_SIM_OFF				(0x20)
-#define AB3100_STR_BATT_REMOVAL				(0x40)
-#define AB3100_STR_VBUS					(0x80)
-
-/*
- * AB3100 contains 8 regulators, one external regulator controller
- * and a buck converter, further the LDO E and buck converter can
- * have separate settings if they are in sleep mode, this is
- * modeled as a separate regulator.
- */
-#define AB3100_NUM_REGULATORS				10
-
-/**
- * struct ab3100
- * @access_mutex: lock out concurrent accesses to the AB3100 registers
- * @dev: pointer to the containing device
- * @i2c_client: I2C client for this chip
- * @testreg_client: secondary client for test registers
- * @chip_name: name of this chip variant
- * @chip_id: 8 bit chip ID for this chip variant
- * @event_subscribers: event subscribers are listed here
- * @startup_events: a copy of the first reading of the event registers
- * @startup_events_read: whether the first events have been read
- *
- * This struct is PRIVATE and devices using it should NOT
- * access ANY fields. It is used as a token for calling the
- * AB3100 functions.
- */
-struct ab3100 {
-	struct mutex access_mutex;
-	struct device *dev;
-	struct i2c_client *i2c_client;
-	struct i2c_client *testreg_client;
-	char chip_name[32];
-	u8 chip_id;
-	struct blocking_notifier_head event_subscribers;
-	u8 startup_events[3];
-	bool startup_events_read;
-};
-
-/**
- * struct ab3100_platform_data
- * Data supplied to initialize board connections to the AB3100
- * @reg_constraints: regulator constraints for target board
- *     the order of these constraints are: LDO A, C, D, E,
- *     F, G, H, K, EXT and BUCK.
- * @reg_initvals: initial values for the regulator registers
- *     plus two sleep settings for LDO E and the BUCK converter.
- *     exactly AB3100_NUM_REGULATORS+2 values must be sent in.
- *     Order: LDO A, C, E, E sleep, F, G, H, K, EXT, BUCK,
- *     BUCK sleep, LDO D. (LDO D need to be initialized last.)
- * @external_voltage: voltage level of the external regulator.
- */
-struct ab3100_platform_data {
-	struct regulator_init_data reg_constraints[AB3100_NUM_REGULATORS];
-	u8 reg_initvals[AB3100_NUM_REGULATORS+2];
-	int external_voltage;
-};
-
-int ab3100_event_register(struct ab3100 *ab3100,
-			  struct notifier_block *nb);
-int ab3100_event_unregister(struct ab3100 *ab3100,
-			    struct notifier_block *nb);
-
 /**
  * struct abx500_init_setting
  * Initial value of the registers for driver to use during setup.