hisi_sas: add v2 hw support for >4 SATA phys
This patch adds support for directly attaching SATA disks to phy
4-8. The problem was that only registers concerned with phy 0-3 were
being considered in sata_int_v2_hw(). The issue was not detected
previously as the development board only exposed phy 0-3; the new board
provides access to 8 phys.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
diff --git a/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c b/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c
index 5a7f709..cc083b9b 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c
@@ -1993,17 +1993,20 @@
u32 ent_tmp, ent_msk, ent_int, port_id, link_rate, hard_phy_linkrate;
irqreturn_t res = IRQ_HANDLED;
u8 attached_sas_addr[SAS_ADDR_SIZE] = {0};
- int phy_no;
+ int phy_no, offset;
phy_no = sas_phy->id;
initial_fis = &hisi_hba->initial_fis[phy_no];
fis = &initial_fis->fis;
- ent_msk = hisi_sas_read32(hisi_hba, ENT_INT_SRC_MSK1);
- hisi_sas_write32(hisi_hba, ENT_INT_SRC_MSK1, ent_msk | 1 << phy_no);
+ offset = 4 * (phy_no / 4);
+ ent_msk = hisi_sas_read32(hisi_hba, ENT_INT_SRC_MSK1 + offset);
+ hisi_sas_write32(hisi_hba, ENT_INT_SRC_MSK1 + offset,
+ ent_msk | 1 << ((phy_no % 4) * 8));
- ent_int = hisi_sas_read32(hisi_hba, ENT_INT_SRC1);
- ent_tmp = ent_int & (1 << (ENT_INT_SRC1_D2H_FIS_CH1_OFF * phy_no));
+ ent_int = hisi_sas_read32(hisi_hba, ENT_INT_SRC1 + offset);
+ ent_tmp = ent_int & (1 << (ENT_INT_SRC1_D2H_FIS_CH1_OFF *
+ (phy_no % 4)));
ent_int >>= ENT_INT_SRC1_D2H_FIS_CH1_OFF * (phy_no % 4);
if ((ent_int & ENT_INT_SRC1_D2H_FIS_CH0_MSK) == 0) {
dev_warn(dev, "sata int: phy%d did not receive FIS\n", phy_no);
@@ -2054,8 +2057,8 @@
queue_work(hisi_hba->wq, &phy->phyup_ws);
end:
- hisi_sas_write32(hisi_hba, ENT_INT_SRC1, ent_tmp);
- hisi_sas_write32(hisi_hba, ENT_INT_SRC_MSK1, ent_msk);
+ hisi_sas_write32(hisi_hba, ENT_INT_SRC1 + offset, ent_tmp);
+ hisi_sas_write32(hisi_hba, ENT_INT_SRC_MSK1 + offset, ent_msk);
return res;
}