[media] rc-core: document the protocol type
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
diff --git a/drivers/media/i2c/ir-kbd-i2c.c b/drivers/media/i2c/ir-kbd-i2c.c
index 143cb2b..f9c4233 100644
--- a/drivers/media/i2c/ir-kbd-i2c.c
+++ b/drivers/media/i2c/ir-kbd-i2c.c
@@ -261,8 +261,9 @@
}
if (rc) {
- dprintk(1, "%s: scancode = 0x%08x\n", __func__, scancode);
- rc_keydown(ir->rc, scancode, toggle);
+ dprintk(1, "%s: proto = 0x%04x, scancode = 0x%08x\n",
+ __func__, protocol, scancode);
+ rc_keydown(ir->rc, protocol, scancode, toggle);
}
return 0;
}
diff --git a/drivers/media/pci/bt8xx/bttv-input.c b/drivers/media/pci/bt8xx/bttv-input.c
index e745f5a..67c8d6b 100644
--- a/drivers/media/pci/bt8xx/bttv-input.c
+++ b/drivers/media/pci/bt8xx/bttv-input.c
@@ -73,12 +73,12 @@
if ((ir->mask_keydown && (gpio & ir->mask_keydown)) ||
(ir->mask_keyup && !(gpio & ir->mask_keyup))) {
- rc_keydown_notimeout(ir->dev, data, 0);
+ rc_keydown_notimeout(ir->dev, RC_TYPE_UNKNOWN, data, 0);
} else {
/* HACK: Probably, ir->mask_keydown is missing
for this board */
if (btv->c.type == BTTV_BOARD_WINFAST2000)
- rc_keydown_notimeout(ir->dev, data, 0);
+ rc_keydown_notimeout(ir->dev, RC_TYPE_UNKNOWN, data, 0);
rc_keyup(ir->dev);
}
@@ -103,7 +103,7 @@
gpio, data,
(gpio & ir->mask_keyup) ? " up" : "up/down");
- rc_keydown_notimeout(ir->dev, data, 0);
+ rc_keydown_notimeout(ir->dev, RC_TYPE_UNKNOWN, data, 0);
if (keyup)
rc_keyup(ir->dev);
} else {
@@ -117,7 +117,7 @@
if (keyup)
rc_keyup(ir->dev);
else
- rc_keydown_notimeout(ir->dev, data, 0);
+ rc_keydown_notimeout(ir->dev, RC_TYPE_UNKNOWN, data, 0);
}
ir->last_gpio = data | keyup;
@@ -241,8 +241,8 @@
return;
}
- scancode = system << 8 | command;
- rc_keydown(ir->dev, scancode, toggle);
+ scancode = RC_SCANCODE_RC5(system, command);
+ rc_keydown(ir->dev, RC_TYPE_RC5, scancode, toggle);
dprintk("scancode %x, toggle %x\n", scancode, toggle);
}
diff --git a/drivers/media/pci/cx88/cx88-input.c b/drivers/media/pci/cx88/cx88-input.c
index 779fc63..9bf48ca 100644
--- a/drivers/media/pci/cx88/cx88-input.c
+++ b/drivers/media/pci/cx88/cx88-input.c
@@ -130,25 +130,41 @@
data = (data << 4) | ((gpio_key & 0xf0) >> 4);
- rc_keydown(ir->dev, data, 0);
+ rc_keydown(ir->dev, RC_TYPE_UNKNOWN, data, 0);
+
+ } else if (ir->core->boardnr == CX88_BOARD_PROLINK_PLAYTVPVR ||
+ ir->core->boardnr == CX88_BOARD_PIXELVIEW_PLAYTV_ULTRA_PRO) {
+ /* bit cleared on keydown, NEC scancode, 0xAAAACC, A = 0x866b */
+ u16 addr;
+ u8 cmd;
+ u32 scancode;
+
+ addr = (data >> 8) & 0xffff;
+ cmd = (data >> 0) & 0x00ff;
+ scancode = RC_SCANCODE_NECX(addr, cmd);
+
+ if (0 == (gpio & ir->mask_keyup))
+ rc_keydown_notimeout(ir->dev, RC_TYPE_NEC, scancode, 0);
+ else
+ rc_keyup(ir->dev);
} else if (ir->mask_keydown) {
/* bit set on keydown */
if (gpio & ir->mask_keydown)
- rc_keydown_notimeout(ir->dev, data, 0);
+ rc_keydown_notimeout(ir->dev, RC_TYPE_UNKNOWN, data, 0);
else
rc_keyup(ir->dev);
} else if (ir->mask_keyup) {
/* bit cleared on keydown */
if (0 == (gpio & ir->mask_keyup))
- rc_keydown_notimeout(ir->dev, data, 0);
+ rc_keydown_notimeout(ir->dev, RC_TYPE_UNKNOWN, data, 0);
else
rc_keyup(ir->dev);
} else {
/* can't distinguish keydown/up :-/ */
- rc_keydown_notimeout(ir->dev, data, 0);
+ rc_keydown_notimeout(ir->dev, RC_TYPE_UNKNOWN, data, 0);
rc_keyup(ir->dev);
}
}
@@ -329,6 +345,7 @@
* 002-T mini RC, provided with newer PV hardware
*/
ir_codes = RC_MAP_PIXELVIEW_MK12;
+ rc_type = RC_BIT_NEC;
ir->gpio_addr = MO_GP1_IO;
ir->mask_keyup = 0x80;
ir->polling = 10; /* ms */
@@ -416,7 +433,6 @@
break;
case CX88_BOARD_TWINHAN_VP1027_DVBS:
ir_codes = RC_MAP_TWINHAN_VP1027_DVBS;
- rc_type = RC_BIT_NEC;
ir->sampling = 0xff00; /* address */
break;
}
diff --git a/drivers/media/pci/dm1105/dm1105.c b/drivers/media/pci/dm1105/dm1105.c
index e60ac35..e8826c5 100644
--- a/drivers/media/pci/dm1105/dm1105.c
+++ b/drivers/media/pci/dm1105/dm1105.c
@@ -678,7 +678,8 @@
data = (ircom >> 8) & 0x7f;
- rc_keydown(ir->dev, data, 0);
+ /* FIXME: UNKNOWN because we don't generate a full NEC scancode (yet?) */
+ rc_keydown(ir->dev, RC_TYPE_UNKNOWN, data, 0);
}
/* work handler */
diff --git a/drivers/media/pci/saa7134/saa7134-input.c b/drivers/media/pci/saa7134/saa7134-input.c
index 73670ed..43dd8bd 100644
--- a/drivers/media/pci/saa7134/saa7134-input.c
+++ b/drivers/media/pci/saa7134/saa7134-input.c
@@ -83,14 +83,14 @@
if (data == ir->mask_keycode)
rc_keyup(ir->dev);
else
- rc_keydown_notimeout(ir->dev, data, 0);
+ rc_keydown_notimeout(ir->dev, RC_TYPE_UNKNOWN, data, 0);
return 0;
}
if (ir->polling) {
if ((ir->mask_keydown && (0 != (gpio & ir->mask_keydown))) ||
(ir->mask_keyup && (0 == (gpio & ir->mask_keyup)))) {
- rc_keydown_notimeout(ir->dev, data, 0);
+ rc_keydown_notimeout(ir->dev, RC_TYPE_UNKNOWN, data, 0);
} else {
rc_keyup(ir->dev);
}
@@ -98,7 +98,7 @@
else { /* IRQ driven mode - handle key press and release in one go */
if ((ir->mask_keydown && (0 != (gpio & ir->mask_keydown))) ||
(ir->mask_keyup && (0 == (gpio & ir->mask_keyup)))) {
- rc_keydown_notimeout(ir->dev, data, 0);
+ rc_keydown_notimeout(ir->dev, RC_TYPE_UNKNOWN, data, 0);
rc_keyup(ir->dev);
}
}
diff --git a/drivers/media/pci/ttpci/budget-ci.c b/drivers/media/pci/ttpci/budget-ci.c
index 0acf920..41ce7de 100644
--- a/drivers/media/pci/ttpci/budget-ci.c
+++ b/drivers/media/pci/ttpci/budget-ci.c
@@ -161,14 +161,14 @@
return;
if (budget_ci->ir.full_rc5) {
- rc_keydown(dev,
- budget_ci->ir.rc5_device <<8 | budget_ci->ir.ir_key,
- (command & 0x20) ? 1 : 0);
+ rc_keydown(dev, RC_TYPE_RC5,
+ RC_SCANCODE_RC5(budget_ci->ir.rc5_device, budget_ci->ir.ir_key),
+ !!(command & 0x20));
return;
}
/* FIXME: We should generate complete scancodes for all devices */
- rc_keydown(dev, budget_ci->ir.ir_key, (command & 0x20) ? 1 : 0);
+ rc_keydown(dev, RC_TYPE_UNKNOWN, budget_ci->ir.ir_key, !!(command & 0x20));
}
static int msp430_ir_init(struct budget_ci *budget_ci)
diff --git a/drivers/media/rc/ati_remote.c b/drivers/media/rc/ati_remote.c
index 2df7c55..8730b32 100644
--- a/drivers/media/rc/ati_remote.c
+++ b/drivers/media/rc/ati_remote.c
@@ -622,8 +622,8 @@
* it would cause ghost repeats which would be a
* regression for this driver.
*/
- rc_keydown_notimeout(ati_remote->rdev, scancode,
- data[2]);
+ rc_keydown_notimeout(ati_remote->rdev, RC_TYPE_OTHER,
+ scancode, data[2]);
rc_keyup(ati_remote->rdev);
}
return;
diff --git a/drivers/media/rc/img-ir/img-ir-hw.c b/drivers/media/rc/img-ir/img-ir-hw.c
index 153c084..b0ec55f 100644
--- a/drivers/media/rc/img-ir/img-ir-hw.c
+++ b/drivers/media/rc/img-ir/img-ir-hw.c
@@ -512,7 +512,7 @@
static int img_ir_set_normal_filter(struct rc_dev *dev,
struct rc_scancode_filter *sc_filter)
{
- return img_ir_set_filter(dev, RC_FILTER_NORMAL, sc_filter);
+ return img_ir_set_filter(dev, RC_FILTER_NORMAL, sc_filter);
}
static int img_ir_set_wakeup_filter(struct rc_dev *dev,
@@ -795,9 +795,11 @@
struct img_ir_priv_hw *hw = &priv->hw;
const struct img_ir_decoder *dec = hw->decoder;
int ret = IMG_IR_SCANCODE;
- int scancode;
+ u32 scancode;
+ enum rc_type protocol = RC_TYPE_UNKNOWN;
+
if (dec->scancode)
- ret = dec->scancode(len, raw, &scancode, hw->enabled_protocols);
+ ret = dec->scancode(len, raw, &protocol, &scancode, hw->enabled_protocols);
else if (len >= 32)
scancode = (u32)raw;
else if (len < 32)
@@ -806,7 +808,7 @@
len, (unsigned long long)raw);
if (ret == IMG_IR_SCANCODE) {
dev_dbg(priv->dev, "decoded scan code %#x\n", scancode);
- rc_keydown(hw->rdev, scancode, 0);
+ rc_keydown(hw->rdev, protocol, scancode, 0);
img_ir_end_repeat(priv);
} else if (ret == IMG_IR_REPEATCODE) {
if (hw->mode == IMG_IR_M_REPEATING) {
diff --git a/drivers/media/rc/img-ir/img-ir-hw.h b/drivers/media/rc/img-ir/img-ir-hw.h
index 450f17d..3e40ce8 100644
--- a/drivers/media/rc/img-ir/img-ir-hw.h
+++ b/drivers/media/rc/img-ir/img-ir-hw.h
@@ -162,7 +162,8 @@
struct img_ir_control control;
/* scancode logic */
- int (*scancode)(int len, u64 raw, int *scancode, u64 protocols);
+ int (*scancode)(int len, u64 raw, enum rc_type *protocol,
+ u32 *scancode, u64 enabled_protocols);
int (*filter)(const struct rc_scancode_filter *in,
struct img_ir_filter *out, u64 protocols);
};
diff --git a/drivers/media/rc/img-ir/img-ir-jvc.c b/drivers/media/rc/img-ir/img-ir-jvc.c
index 85ee90f..a60dda8 100644
--- a/drivers/media/rc/img-ir/img-ir-jvc.c
+++ b/drivers/media/rc/img-ir/img-ir-jvc.c
@@ -12,7 +12,8 @@
#include "img-ir-hw.h"
/* Convert JVC data to a scancode */
-static int img_ir_jvc_scancode(int len, u64 raw, int *scancode, u64 protocols)
+static int img_ir_jvc_scancode(int len, u64 raw, enum rc_type *protocol,
+ u32 *scancode, u64 enabled_protocols)
{
unsigned int cust, data;
@@ -22,6 +23,7 @@
cust = (raw >> 0) & 0xff;
data = (raw >> 8) & 0xff;
+ *protocol = RC_TYPE_JVC;
*scancode = cust << 8 | data;
return IMG_IR_SCANCODE;
}
diff --git a/drivers/media/rc/img-ir/img-ir-nec.c b/drivers/media/rc/img-ir/img-ir-nec.c
index f7520e2..7398975 100644
--- a/drivers/media/rc/img-ir/img-ir-nec.c
+++ b/drivers/media/rc/img-ir/img-ir-nec.c
@@ -13,7 +13,8 @@
#include <linux/bitrev.h>
/* Convert NEC data to a scancode */
-static int img_ir_nec_scancode(int len, u64 raw, int *scancode, u64 protocols)
+static int img_ir_nec_scancode(int len, u64 raw, enum rc_type *protocol,
+ u32 *scancode, u64 enabled_protocols)
{
unsigned int addr, addr_inv, data, data_inv;
/* a repeat code has no data */
@@ -45,6 +46,7 @@
*scancode = addr << 8 |
data;
}
+ *protocol = RC_TYPE_NEC;
return IMG_IR_SCANCODE;
}
diff --git a/drivers/media/rc/img-ir/img-ir-sanyo.c b/drivers/media/rc/img-ir/img-ir-sanyo.c
index 6755c94..6b0653e 100644
--- a/drivers/media/rc/img-ir/img-ir-sanyo.c
+++ b/drivers/media/rc/img-ir/img-ir-sanyo.c
@@ -23,7 +23,8 @@
#include "img-ir-hw.h"
/* Convert Sanyo data to a scancode */
-static int img_ir_sanyo_scancode(int len, u64 raw, int *scancode, u64 protocols)
+static int img_ir_sanyo_scancode(int len, u64 raw, enum rc_type *protocol,
+ u32 *scancode, u64 enabled_protocols)
{
unsigned int addr, addr_inv, data, data_inv;
/* a repeat code has no data */
@@ -43,6 +44,7 @@
return -EINVAL;
/* Normal Sanyo */
+ *protocol = RC_TYPE_SANYO;
*scancode = addr << 8 | data;
return IMG_IR_SCANCODE;
}
diff --git a/drivers/media/rc/img-ir/img-ir-sharp.c b/drivers/media/rc/img-ir/img-ir-sharp.c
index 5867be0..3300a38 100644
--- a/drivers/media/rc/img-ir/img-ir-sharp.c
+++ b/drivers/media/rc/img-ir/img-ir-sharp.c
@@ -12,7 +12,8 @@
#include "img-ir-hw.h"
/* Convert Sharp data to a scancode */
-static int img_ir_sharp_scancode(int len, u64 raw, int *scancode, u64 protocols)
+static int img_ir_sharp_scancode(int len, u64 raw, enum rc_type *protocol,
+ u32 *scancode, u64 enabled_protocols)
{
unsigned int addr, cmd, exp, chk;
@@ -31,6 +32,7 @@
/* probably the second half of the message */
return -EINVAL;
+ *protocol = RC_TYPE_SHARP;
*scancode = addr << 8 | cmd;
return IMG_IR_SCANCODE;
}
diff --git a/drivers/media/rc/img-ir/img-ir-sony.c b/drivers/media/rc/img-ir/img-ir-sony.c
index b9029ae..3a0f17b 100644
--- a/drivers/media/rc/img-ir/img-ir-sony.c
+++ b/drivers/media/rc/img-ir/img-ir-sony.c
@@ -12,35 +12,39 @@
#include "img-ir-hw.h"
/* Convert Sony data to a scancode */
-static int img_ir_sony_scancode(int len, u64 raw, int *scancode, u64 protocols)
+static int img_ir_sony_scancode(int len, u64 raw, enum rc_type *protocol,
+ u32 *scancode, u64 enabled_protocols)
{
unsigned int dev, subdev, func;
switch (len) {
case 12:
- if (!(protocols & RC_BIT_SONY12))
+ if (!(enabled_protocols & RC_BIT_SONY12))
return -EINVAL;
func = raw & 0x7f; /* first 7 bits */
raw >>= 7;
dev = raw & 0x1f; /* next 5 bits */
subdev = 0;
+ *protocol = RC_TYPE_SONY12;
break;
case 15:
- if (!(protocols & RC_BIT_SONY15))
+ if (!(enabled_protocols & RC_BIT_SONY15))
return -EINVAL;
func = raw & 0x7f; /* first 7 bits */
raw >>= 7;
dev = raw & 0xff; /* next 8 bits */
subdev = 0;
+ *protocol = RC_TYPE_SONY15;
break;
case 20:
- if (!(protocols & RC_BIT_SONY20))
+ if (!(enabled_protocols & RC_BIT_SONY20))
return -EINVAL;
func = raw & 0x7f; /* first 7 bits */
raw >>= 7;
dev = raw & 0x1f; /* next 5 bits */
raw >>= 5;
subdev = raw & 0xff; /* next 8 bits */
+ *protocol = RC_TYPE_SONY20;
break;
default:
return -EINVAL;
diff --git a/drivers/media/rc/imon.c b/drivers/media/rc/imon.c
index 6f24e77..eb37f26 100644
--- a/drivers/media/rc/imon.c
+++ b/drivers/media/rc/imon.c
@@ -1579,7 +1579,10 @@
if (press_type == 0)
rc_keyup(ictx->rdev);
else {
- rc_keydown(ictx->rdev, ictx->rc_scancode, ictx->rc_toggle);
+ if (ictx->rc_type == RC_BIT_RC6_MCE)
+ rc_keydown(ictx->rdev,
+ ictx->rc_type == RC_BIT_RC6_MCE ? RC_TYPE_RC6_MCE : RC_TYPE_OTHER,
+ ictx->rc_scancode, ictx->rc_toggle);
spin_lock_irqsave(&ictx->kc_lock, flags);
ictx->last_keycode = ictx->kc;
spin_unlock_irqrestore(&ictx->kc_lock, flags);
diff --git a/drivers/media/rc/ir-jvc-decoder.c b/drivers/media/rc/ir-jvc-decoder.c
index 4ea62a1..7b79eca 100644
--- a/drivers/media/rc/ir-jvc-decoder.c
+++ b/drivers/media/rc/ir-jvc-decoder.c
@@ -140,7 +140,7 @@
scancode = (bitrev8((data->bits >> 8) & 0xff) << 8) |
(bitrev8((data->bits >> 0) & 0xff) << 0);
IR_dprintk(1, "JVC scancode 0x%04x\n", scancode);
- rc_keydown(dev, scancode, data->toggle);
+ rc_keydown(dev, RC_TYPE_JVC, scancode, data->toggle);
data->first = false;
data->old_bits = data->bits;
} else if (data->bits == data->old_bits) {
diff --git a/drivers/media/rc/ir-nec-decoder.c b/drivers/media/rc/ir-nec-decoder.c
index 35c42e5..c4333d5 100644
--- a/drivers/media/rc/ir-nec-decoder.c
+++ b/drivers/media/rc/ir-nec-decoder.c
@@ -189,7 +189,7 @@
if (data->is_nec_x)
data->necx_repeat = true;
- rc_keydown(dev, scancode, 0);
+ rc_keydown(dev, RC_TYPE_NEC, scancode, 0);
data->state = STATE_INACTIVE;
return 0;
}
diff --git a/drivers/media/rc/ir-rc5-decoder.c b/drivers/media/rc/ir-rc5-decoder.c
index 4295d9b..3d38cbc 100644
--- a/drivers/media/rc/ir-rc5-decoder.c
+++ b/drivers/media/rc/ir-rc5-decoder.c
@@ -51,6 +51,7 @@
struct rc5_dec *data = &dev->raw->rc5;
u8 toggle;
u32 scancode;
+ enum rc_type protocol;
if (!rc_protocols_enabled(dev, RC_BIT_RC5 | RC_BIT_RC5X))
return 0;
@@ -138,6 +139,7 @@
toggle = (data->bits & 0x20000) ? 1 : 0;
command += (data->bits & 0x01000) ? 0 : 0x40;
scancode = system << 16 | command << 8 | xdata;
+ protocol = RC_TYPE_RC5X;
IR_dprintk(1, "RC5X scancode 0x%06x (toggle: %u)\n",
scancode, toggle);
@@ -154,12 +156,13 @@
toggle = (data->bits & 0x00800) ? 1 : 0;
command += (data->bits & 0x01000) ? 0 : 0x40;
scancode = system << 8 | command;
+ protocol = RC_TYPE_RC5;
IR_dprintk(1, "RC5 scancode 0x%04x (toggle: %u)\n",
scancode, toggle);
}
- rc_keydown(dev, scancode, toggle);
+ rc_keydown(dev, protocol, scancode, toggle);
data->state = STATE_INACTIVE;
return 0;
}
diff --git a/drivers/media/rc/ir-rc5-sz-decoder.c b/drivers/media/rc/ir-rc5-sz-decoder.c
index dc18b74..85c7711 100644
--- a/drivers/media/rc/ir-rc5-sz-decoder.c
+++ b/drivers/media/rc/ir-rc5-sz-decoder.c
@@ -115,7 +115,7 @@
IR_dprintk(1, "RC5-sz scancode 0x%04x (toggle: %u)\n",
scancode, toggle);
- rc_keydown(dev, scancode, toggle);
+ rc_keydown(dev, RC_TYPE_RC5_SZ, scancode, toggle);
data->state = STATE_INACTIVE;
return 0;
}
diff --git a/drivers/media/rc/ir-rc6-decoder.c b/drivers/media/rc/ir-rc6-decoder.c
index cfbd64e..1dc97a7 100644
--- a/drivers/media/rc/ir-rc6-decoder.c
+++ b/drivers/media/rc/ir-rc6-decoder.c
@@ -88,6 +88,7 @@
struct rc6_dec *data = &dev->raw->rc6;
u32 scancode;
u8 toggle;
+ enum rc_type protocol;
if (!rc_protocols_enabled(dev, RC_BIT_RC6_0 | RC_BIT_RC6_6A_20 |
RC_BIT_RC6_6A_24 | RC_BIT_RC6_6A_32 |
@@ -233,9 +234,11 @@
case RC6_MODE_0:
scancode = data->body;
toggle = data->toggle;
+ protocol = RC_TYPE_RC6_0;
IR_dprintk(1, "RC6(0) scancode 0x%04x (toggle: %u)\n",
scancode, toggle);
break;
+
case RC6_MODE_6A:
if (data->count > CHAR_BIT * sizeof data->body) {
IR_dprintk(1, "RC6 too many (%u) data bits\n",
@@ -244,23 +247,39 @@
}
scancode = data->body;
- if (data->count == RC6_6A_32_NBITS &&
- (scancode & RC6_6A_LCC_MASK) == RC6_6A_MCE_CC) {
- /* MCE RC */
- toggle = (scancode & RC6_6A_MCE_TOGGLE_MASK) ? 1 : 0;
- scancode &= ~RC6_6A_MCE_TOGGLE_MASK;
- } else {
+ switch (data->count) {
+ case 20:
+ protocol = RC_TYPE_RC6_6A_20;
toggle = 0;
+ break;
+ case 24:
+ protocol = RC_BIT_RC6_6A_24;
+ toggle = 0;
+ break;
+ case 32:
+ if ((scancode & RC6_6A_LCC_MASK) == RC6_6A_MCE_CC) {
+ protocol = RC_TYPE_RC6_MCE;
+ scancode &= ~RC6_6A_MCE_TOGGLE_MASK;
+ toggle = !!(scancode & RC6_6A_MCE_TOGGLE_MASK);
+ } else {
+ protocol = RC_BIT_RC6_6A_32;
+ toggle = 0;
+ }
+ break;
+ default:
+ IR_dprintk(1, "RC6(6A) unsupported length\n");
+ goto out;
}
- IR_dprintk(1, "RC6(6A) scancode 0x%08x (toggle: %u)\n",
- scancode, toggle);
+
+ IR_dprintk(1, "RC6(6A) proto 0x%04x, scancode 0x%08x (toggle: %u)\n",
+ protocol, scancode, toggle);
break;
default:
IR_dprintk(1, "RC6 unknown mode\n");
goto out;
}
- rc_keydown(dev, scancode, toggle);
+ rc_keydown(dev, protocol, scancode, toggle);
data->state = STATE_INACTIVE;
return 0;
}
diff --git a/drivers/media/rc/ir-sanyo-decoder.c b/drivers/media/rc/ir-sanyo-decoder.c
index eb715f0..5f77022 100644
--- a/drivers/media/rc/ir-sanyo-decoder.c
+++ b/drivers/media/rc/ir-sanyo-decoder.c
@@ -167,7 +167,7 @@
scancode = address << 8 | command;
IR_dprintk(1, "SANYO scancode: 0x%06x\n", scancode);
- rc_keydown(dev, scancode, 0);
+ rc_keydown(dev, RC_TYPE_SANYO, scancode, 0);
data->state = STATE_INACTIVE;
return 0;
}
diff --git a/drivers/media/rc/ir-sharp-decoder.c b/drivers/media/rc/ir-sharp-decoder.c
index 66d2039..c8f2519 100644
--- a/drivers/media/rc/ir-sharp-decoder.c
+++ b/drivers/media/rc/ir-sharp-decoder.c
@@ -162,7 +162,7 @@
scancode = address << 8 | command;
IR_dprintk(1, "Sharp scancode 0x%04x\n", scancode);
- rc_keydown(dev, scancode, 0);
+ rc_keydown(dev, RC_TYPE_SHARP, scancode, 0);
data->state = STATE_INACTIVE;
return 0;
}
diff --git a/drivers/media/rc/ir-sony-decoder.c b/drivers/media/rc/ir-sony-decoder.c
index 599c19a..f485f9fe 100644
--- a/drivers/media/rc/ir-sony-decoder.c
+++ b/drivers/media/rc/ir-sony-decoder.c
@@ -42,6 +42,7 @@
static int ir_sony_decode(struct rc_dev *dev, struct ir_raw_event ev)
{
struct sony_dec *data = &dev->raw->sony;
+ enum rc_type protocol;
u32 scancode;
u8 device, subdevice, function;
@@ -131,6 +132,7 @@
device = bitrev8((data->bits << 3) & 0xF8);
subdevice = 0;
function = bitrev8((data->bits >> 4) & 0xFE);
+ protocol = RC_TYPE_SONY12;
break;
case 15:
if (!rc_protocols_enabled(dev, RC_BIT_SONY15)) {
@@ -140,6 +142,7 @@
device = bitrev8((data->bits >> 0) & 0xFF);
subdevice = 0;
function = bitrev8((data->bits >> 7) & 0xFE);
+ protocol = RC_TYPE_SONY15;
break;
case 20:
if (!rc_protocols_enabled(dev, RC_BIT_SONY20)) {
@@ -149,6 +152,7 @@
device = bitrev8((data->bits >> 5) & 0xF8);
subdevice = bitrev8((data->bits >> 0) & 0xFF);
function = bitrev8((data->bits >> 12) & 0xFE);
+ protocol = RC_TYPE_SONY20;
break;
default:
IR_dprintk(1, "Sony invalid bitcount %u\n", data->count);
@@ -157,7 +161,7 @@
scancode = device << 16 | subdevice << 8 | function;
IR_dprintk(1, "Sony(%u) scancode 0x%05x\n", data->count, scancode);
- rc_keydown(dev, scancode, 0);
+ rc_keydown(dev, protocol, scancode, 0);
data->state = STATE_INACTIVE;
return 0;
}
diff --git a/drivers/media/rc/rc-main.c b/drivers/media/rc/rc-main.c
index 970b93d..9abcf77 100644
--- a/drivers/media/rc/rc-main.c
+++ b/drivers/media/rc/rc-main.c
@@ -623,6 +623,7 @@
/**
* ir_do_keydown() - internal function to process a keypress
* @dev: the struct rc_dev descriptor of the device
+ * @protocol: the protocol of the keypress
* @scancode: the scancode of the keypress
* @keycode: the keycode of the keypress
* @toggle: the toggle value of the keypress
@@ -630,12 +631,13 @@
* This function is used internally to register a keypress, it must be
* called with keylock held.
*/
-static void ir_do_keydown(struct rc_dev *dev, int scancode,
- u32 keycode, u8 toggle)
+static void ir_do_keydown(struct rc_dev *dev, enum rc_type protocol,
+ u32 scancode, u32 keycode, u8 toggle)
{
bool new_event = (!dev->keypressed ||
+ dev->last_protocol != protocol ||
dev->last_scancode != scancode ||
- dev->last_toggle != toggle);
+ dev->last_toggle != toggle);
if (new_event && dev->keypressed)
ir_do_keyup(dev, false);
@@ -645,13 +647,14 @@
if (new_event && keycode != KEY_RESERVED) {
/* Register a keypress */
dev->keypressed = true;
+ dev->last_protocol = protocol;
dev->last_scancode = scancode;
dev->last_toggle = toggle;
dev->last_keycode = keycode;
IR_dprintk(1, "%s: key down event, "
- "key 0x%04x, scancode 0x%04x\n",
- dev->input_name, keycode, scancode);
+ "key 0x%04x, protocol 0x%04x, scancode 0x%08x\n",
+ dev->input_name, keycode, protocol, scancode);
input_report_key(dev->input_dev, keycode, 1);
led_trigger_event(led_feedback, LED_FULL);
@@ -663,20 +666,21 @@
/**
* rc_keydown() - generates input event for a key press
* @dev: the struct rc_dev descriptor of the device
- * @scancode: the scancode that we're seeking
+ * @protocol: the protocol for the keypress
+ * @scancode: the scancode for the keypress
* @toggle: the toggle value (protocol dependent, if the protocol doesn't
* support toggle values, this should be set to zero)
*
* This routine is used to signal that a key has been pressed on the
* remote control.
*/
-void rc_keydown(struct rc_dev *dev, int scancode, u8 toggle)
+void rc_keydown(struct rc_dev *dev, enum rc_type protocol, u32 scancode, u8 toggle)
{
unsigned long flags;
u32 keycode = rc_g_keycode_from_table(dev, scancode);
spin_lock_irqsave(&dev->keylock, flags);
- ir_do_keydown(dev, scancode, keycode, toggle);
+ ir_do_keydown(dev, protocol, scancode, keycode, toggle);
if (dev->keypressed) {
dev->keyup_jiffies = jiffies + msecs_to_jiffies(IR_KEYPRESS_TIMEOUT);
@@ -690,20 +694,22 @@
* rc_keydown_notimeout() - generates input event for a key press without
* an automatic keyup event at a later time
* @dev: the struct rc_dev descriptor of the device
- * @scancode: the scancode that we're seeking
+ * @protocol: the protocol for the keypress
+ * @scancode: the scancode for the keypress
* @toggle: the toggle value (protocol dependent, if the protocol doesn't
* support toggle values, this should be set to zero)
*
* This routine is used to signal that a key has been pressed on the
* remote control. The driver must manually call rc_keyup() at a later stage.
*/
-void rc_keydown_notimeout(struct rc_dev *dev, int scancode, u8 toggle)
+void rc_keydown_notimeout(struct rc_dev *dev, enum rc_type protocol,
+ u32 scancode, u8 toggle)
{
unsigned long flags;
u32 keycode = rc_g_keycode_from_table(dev, scancode);
spin_lock_irqsave(&dev->keylock, flags);
- ir_do_keydown(dev, scancode, keycode, toggle);
+ ir_do_keydown(dev, protocol, scancode, keycode, toggle);
spin_unlock_irqrestore(&dev->keylock, flags);
}
EXPORT_SYMBOL_GPL(rc_keydown_notimeout);
@@ -1315,7 +1321,7 @@
dev->dev.groups = dev->sysfs_groups;
dev->sysfs_groups[attr++] = &rc_dev_protocol_attr_grp;
if (dev->s_filter)
- dev->sysfs_groups[attr++] = &rc_dev_filter_attr_grp;
+ dev->sysfs_groups[attr++] = &rc_dev_filter_attr_grp;
if (dev->s_wakeup_filter)
dev->sysfs_groups[attr++] = &rc_dev_wakeup_filter_attr_grp;
if (dev->change_wakeup_protocol)
diff --git a/drivers/media/usb/dvb-usb-v2/af9015.c b/drivers/media/usb/dvb-usb-v2/af9015.c
index da47d23..5ca738a 100644
--- a/drivers/media/usb/dvb-usb-v2/af9015.c
+++ b/drivers/media/usb/dvb-usb-v2/af9015.c
@@ -1213,7 +1213,7 @@
if ((state->rc_repeat != buf[6] || buf[0]) &&
!memcmp(&buf[12], state->rc_last, 4)) {
dev_dbg(&d->udev->dev, "%s: key repeated\n", __func__);
- rc_keydown(d->rc_dev, state->rc_keycode, 0);
+ rc_repeat(d->rc_dev);
state->rc_repeat = buf[6];
return ret;
}
@@ -1233,18 +1233,22 @@
if (buf[14] == (u8) ~buf[15]) {
if (buf[12] == (u8) ~buf[13]) {
/* NEC */
- state->rc_keycode = buf[12] << 8 | buf[14];
+ state->rc_keycode = RC_SCANCODE_NEC(buf[12],
+ buf[14]);
} else {
/* NEC extended*/
- state->rc_keycode = buf[12] << 16 |
- buf[13] << 8 | buf[14];
+ state->rc_keycode = RC_SCANCODE_NECX(buf[12] << 8 |
+ buf[13],
+ buf[14]);
}
} else {
/* 32 bit NEC */
- state->rc_keycode = buf[12] << 24 | buf[13] << 16 |
- buf[14] << 8 | buf[15];
+ state->rc_keycode = RC_SCANCODE_NEC32(buf[12] << 24 |
+ buf[13] << 16 |
+ buf[14] << 8 |
+ buf[15]);
}
- rc_keydown(d->rc_dev, state->rc_keycode, 0);
+ rc_keydown(d->rc_dev, RC_TYPE_NEC, state->rc_keycode, 0);
} else {
dev_dbg(&d->udev->dev, "%s: no key press\n", __func__);
/* Invalidate last keypress */
diff --git a/drivers/media/usb/dvb-usb-v2/af9035.c b/drivers/media/usb/dvb-usb-v2/af9035.c
index 7b9b75f..221af2b 100644
--- a/drivers/media/usb/dvb-usb-v2/af9035.c
+++ b/drivers/media/usb/dvb-usb-v2/af9035.c
@@ -1313,19 +1313,20 @@
if ((buf[2] + buf[3]) == 0xff) {
if ((buf[0] + buf[1]) == 0xff) {
/* NEC standard 16bit */
- key = buf[0] << 8 | buf[2];
+ key = RC_SCANCODE_NEC(buf[0], buf[2]);
} else {
/* NEC extended 24bit */
- key = buf[0] << 16 | buf[1] << 8 | buf[2];
+ key = RC_SCANCODE_NECX(buf[0] << 8 | buf[1], buf[2]);
}
} else {
/* NEC full code 32bit */
- key = buf[0] << 24 | buf[1] << 16 | buf[2] << 8 | buf[3];
+ key = RC_SCANCODE_NEC32(buf[0] << 24 | buf[1] << 16 |
+ buf[2] << 8 | buf[3]);
}
dev_dbg(&d->udev->dev, "%s: %*ph\n", __func__, 4, buf);
- rc_keydown(d->rc_dev, key, 0);
+ rc_keydown(d->rc_dev, RC_TYPE_NEC, key, 0);
return 0;
diff --git a/drivers/media/usb/dvb-usb-v2/anysee.c b/drivers/media/usb/dvb-usb-v2/anysee.c
index eeab79b..e4a2382 100644
--- a/drivers/media/usb/dvb-usb-v2/anysee.c
+++ b/drivers/media/usb/dvb-usb-v2/anysee.c
@@ -1038,7 +1038,8 @@
if (ircode[0]) {
dev_dbg(&d->udev->dev, "%s: key pressed %02x\n", __func__,
ircode[1]);
- rc_keydown(d->rc_dev, 0x08 << 8 | ircode[1], 0);
+ rc_keydown(d->rc_dev, RC_TYPE_NEC,
+ RC_SCANCODE_NEC(0x08, ircode[1]), 0);
}
return 0;
diff --git a/drivers/media/usb/dvb-usb-v2/az6007.c b/drivers/media/usb/dvb-usb-v2/az6007.c
index c3c4b98..935dbaa 100644
--- a/drivers/media/usb/dvb-usb-v2/az6007.c
+++ b/drivers/media/usb/dvb-usb-v2/az6007.c
@@ -207,24 +207,27 @@
static int az6007_rc_query(struct dvb_usb_device *d)
{
struct az6007_device_state *st = d_to_priv(d);
- unsigned code = 0;
+ unsigned code;
az6007_read(d, AZ6007_READ_IR, 0, 0, st->data, 10);
if (st->data[1] == 0x44)
return 0;
- if ((st->data[1] ^ st->data[2]) == 0xff)
- code = st->data[1];
- else
- code = st->data[1] << 8 | st->data[2];
+ if ((st->data[3] ^ st->data[4]) == 0xff) {
+ if ((st->data[1] ^ st->data[2]) == 0xff)
+ code = RC_SCANCODE_NEC(st->data[1], st->data[3]);
+ else
+ code = RC_SCANCODE_NECX(st->data[1] << 8 | st->data[2],
+ st->data[3]);
+ } else {
+ code = RC_SCANCODE_NEC32(st->data[1] << 24 |
+ st->data[2] << 16 |
+ st->data[3] << 8 |
+ st->data[4]);
+ }
- if ((st->data[3] ^ st->data[4]) == 0xff)
- code = code << 8 | st->data[3];
- else
- code = code << 16 | st->data[3] << 8 | st->data[4];
-
- rc_keydown(d->rc_dev, code, st->data[5]);
+ rc_keydown(d->rc_dev, RC_TYPE_NEC, code, st->data[5]);
return 0;
}
diff --git a/drivers/media/usb/dvb-usb-v2/lmedm04.c b/drivers/media/usb/dvb-usb-v2/lmedm04.c
index 7d685bc..e332af7 100644
--- a/drivers/media/usb/dvb-usb-v2/lmedm04.c
+++ b/drivers/media/usb/dvb-usb-v2/lmedm04.c
@@ -286,14 +286,13 @@
case 0xaa:
debug_data_snipet(1, "INT Remote data snipet", ibuf);
if ((ibuf[4] + ibuf[5]) == 0xff) {
- key = ibuf[5];
- key += (ibuf[3] > 0)
- ? (ibuf[3] ^ 0xff) << 8 : 0;
- key += (ibuf[2] ^ 0xff) << 16;
+ key = RC_SCANCODE_NECX((ibuf[2] ^ 0xff) << 8 |
+ (ibuf[3] > 0) ? (ibuf[3] ^ 0xff) : 0,
+ ibuf[5]);
deb_info(1, "INT Key =%08x", key);
if (adap_to_d(adap)->rc_dev != NULL)
rc_keydown(adap_to_d(adap)->rc_dev,
- key, 0);
+ RC_TYPE_NEC, key, 0);
}
break;
case 0xbb:
diff --git a/drivers/media/usb/dvb-usb-v2/rtl28xxu.c b/drivers/media/usb/dvb-usb-v2/rtl28xxu.c
index a676e44..57ac62d 100644
--- a/drivers/media/usb/dvb-usb-v2/rtl28xxu.c
+++ b/drivers/media/usb/dvb-usb-v2/rtl28xxu.c
@@ -1287,19 +1287,19 @@
if (buf[2] == (u8) ~buf[3]) {
if (buf[0] == (u8) ~buf[1]) {
/* NEC standard (16 bit) */
- rc_code = buf[0] << 8 | buf[2];
+ rc_code = RC_SCANCODE_NEC(buf[0], buf[2]);
} else {
/* NEC extended (24 bit) */
- rc_code = buf[0] << 16 |
- buf[1] << 8 | buf[2];
+ rc_code = RC_SCANCODE_NECX(buf[0] << 8 | buf[1],
+ buf[2]);
}
} else {
/* NEC full (32 bit) */
- rc_code = buf[0] << 24 | buf[1] << 16 |
- buf[2] << 8 | buf[3];
+ rc_code = RC_SCANCODE_NEC32(buf[0] << 24 | buf[1] << 16 |
+ buf[2] << 8 | buf[3]);
}
- rc_keydown(d->rc_dev, rc_code, 0);
+ rc_keydown(d->rc_dev, RC_TYPE_NEC, rc_code, 0);
ret = rtl28xx_wr_reg(d, SYS_IRRC_SR, 1);
if (ret)
diff --git a/drivers/media/usb/dvb-usb/cxusb.c b/drivers/media/usb/dvb-usb/cxusb.c
index f379f7e..16bc579 100644
--- a/drivers/media/usb/dvb-usb/cxusb.c
+++ b/drivers/media/usb/dvb-usb/cxusb.c
@@ -541,7 +541,7 @@
rc5_addr = (cmd & 0x07C0) >> 6; /* bits 7-11 for address */
rc5_toggle = (cmd & 0x0800) >> 11; /* bit 12 for toggle */
keycode = (rc5_addr << 8) | rc5_cmd;
- rc_keydown(d->rc_dev, keycode, rc5_toggle);
+ rc_keydown(d->rc_dev, RC_BIT_RC5, keycode, rc5_toggle);
}
return 0;
diff --git a/drivers/media/usb/dvb-usb/dib0700_core.c b/drivers/media/usb/dvb-usb/dib0700_core.c
index 38b151f..50856db 100644
--- a/drivers/media/usb/dvb-usb/dib0700_core.c
+++ b/drivers/media/usb/dvb-usb/dib0700_core.c
@@ -669,6 +669,7 @@
{
struct dvb_usb_device *d = purb->context;
struct dib0700_rc_response *poll_reply;
+ enum rc_type protocol;
u32 uninitialized_var(keycode);
u8 toggle;
@@ -702,6 +703,7 @@
switch (d->props.rc.core.protocol) {
case RC_BIT_NEC:
+ protocol = RC_TYPE_NEC;
toggle = 0;
/* NEC protocol sends repeat code as 0 0 0 FF */
@@ -724,6 +726,7 @@
keycode = RC_SCANCODE_NECX(poll_reply->system << 8 |
poll_reply->not_system,
poll_reply->data);
+
} else {
deb_data("NEC normal protocol\n");
keycode = RC_SCANCODE_NEC(poll_reply->system,
@@ -733,9 +736,9 @@
break;
default:
deb_data("RC5 protocol\n");
- /* RC5 Protocol */
+ protocol = RC_TYPE_RC5;
toggle = poll_reply->report_id;
- keycode = poll_reply->system << 8 | poll_reply->data;
+ keycode = RC_SCANCODE_RC5(poll_reply->system, poll_reply->data);
break;
}
@@ -748,7 +751,7 @@
goto resubmit;
}
- rc_keydown(d->rc_dev, keycode, toggle);
+ rc_keydown(d->rc_dev, protocol, keycode, toggle);
resubmit:
/* Clean the buffer before we requeue */
diff --git a/drivers/media/usb/dvb-usb/dib0700_devices.c b/drivers/media/usb/dvb-usb/dib0700_devices.c
index 501947e..91e5ebb0 100644
--- a/drivers/media/usb/dvb-usb/dib0700_devices.c
+++ b/drivers/media/usb/dvb-usb/dib0700_devices.c
@@ -512,7 +512,8 @@
static int dib0700_rc_query_old_firmware(struct dvb_usb_device *d)
{
u8 key[4];
- u32 keycode;
+ enum rc_type protocol;
+ u32 scancode;
u8 toggle;
int i;
struct dib0700_state *st = d->priv;
@@ -539,28 +540,29 @@
dib0700_rc_setup(d, NULL); /* reset ir sensor data to prevent false events */
- d->last_event = 0;
switch (d->props.rc.core.protocol) {
case RC_BIT_NEC:
/* NEC protocol sends repeat code as 0 0 0 FF */
if ((key[3-2] == 0x00) && (key[3-3] == 0x00) &&
- (key[3] == 0xff))
- keycode = d->last_event;
- else {
- keycode = key[3-2] << 8 | key[3-3];
- d->last_event = keycode;
+ (key[3] == 0xff)) {
+ rc_repeat(d->rc_dev);
+ return 0;
}
- rc_keydown(d->rc_dev, keycode, 0);
+ protocol = RC_TYPE_NEC;
+ scancode = RC_SCANCODE_NEC(key[3-2], key[3-3]);
+ toggle = 0;
break;
+
default:
/* RC-5 protocol changes toggle bit on new keypress */
- keycode = key[3-2] << 8 | key[3-3];
+ protocol = RC_TYPE_RC5;
+ scancode = RC_SCANCODE_RC5(key[3-2], key[3-3]);
toggle = key[3-1];
- rc_keydown(d->rc_dev, keycode, toggle);
-
break;
}
+
+ rc_keydown(d->rc_dev, protocol, scancode, toggle);
return 0;
}
diff --git a/drivers/media/usb/dvb-usb/dw2102.c b/drivers/media/usb/dvb-usb/dw2102.c
index 7135a3e..2add8c5 100644
--- a/drivers/media/usb/dvb-usb/dw2102.c
+++ b/drivers/media/usb/dvb-usb/dw2102.c
@@ -1490,7 +1490,7 @@
if (msg.buf[0] != 0xff) {
deb_rc("%s: rc code: %x, %x\n",
__func__, key[0], key[1]);
- rc_keydown(d->rc_dev, key[0], 1);
+ rc_keydown(d->rc_dev, RC_TYPE_UNKNOWN, key[0], 0);
}
}
@@ -1511,7 +1511,7 @@
if (msg.buf[0] != 0xff) {
deb_rc("%s: rc code: %x, %x\n",
__func__, key[0], key[1]);
- rc_keydown(d->rc_dev, key[0]^0xff, 1);
+ rc_keydown(d->rc_dev, RC_TYPE_UNKNOWN, key[0]^0xff, 0);
}
}
@@ -1532,7 +1532,8 @@
if (msg.buf[0] != 0xff) {
deb_rc("%s: rc code: %x, %x\n",
__func__, key[0], key[1]);
- rc_keydown(d->rc_dev, key[1] << 8 | key[0], 1);
+ rc_keydown(d->rc_dev, RC_TYPE_RC5,
+ RC_SCANCODE_RC5(key[1], key[0]), 0);
}
}
diff --git a/drivers/media/usb/dvb-usb/m920x.c b/drivers/media/usb/dvb-usb/m920x.c
index 0306cb7..abf8ab2 100644
--- a/drivers/media/usb/dvb-usb/m920x.c
+++ b/drivers/media/usb/dvb-usb/m920x.c
@@ -245,7 +245,7 @@
else if (state == REMOTE_KEY_REPEAT)
rc_repeat(d->rc_dev);
else
- rc_keydown(d->rc_dev, rc_state[1], 0);
+ rc_keydown(d->rc_dev, RC_TYPE_UNKNOWN, rc_state[1], 0);
out:
kfree(rc_state);
diff --git a/drivers/media/usb/dvb-usb/pctv452e.c b/drivers/media/usb/dvb-usb/pctv452e.c
index 449a996..bdfe896 100644
--- a/drivers/media/usb/dvb-usb/pctv452e.c
+++ b/drivers/media/usb/dvb-usb/pctv452e.c
@@ -565,12 +565,12 @@
if ((rx[3] == 9) && (rx[12] & 0x01)) {
/* got a "press" event */
- state->last_rc_key = (rx[7] << 8) | rx[6];
+ state->last_rc_key = RC_SCANCODE_RC5(rx[7], rx[6]);
if (debug > 2)
info("%s: cmd=0x%02x sys=0x%02x\n",
__func__, rx[6], rx[7]);
- rc_keydown(d->rc_dev, state->last_rc_key, 0);
+ rc_keydown(d->rc_dev, RC_TYPE_RC5, state->last_rc_key, 0);
} else if (state->last_rc_key) {
rc_keyup(d->rc_dev);
state->last_rc_key = 0;
@@ -927,7 +927,7 @@
.rc.core = {
.rc_codes = RC_MAP_DIB0700_RC5_TABLE,
- .allowed_protos = RC_BIT_UNKNOWN,
+ .allowed_protos = RC_BIT_RC5,
.rc_query = pctv452e_rc_query,
.rc_interval = 100,
},
@@ -980,7 +980,7 @@
.rc.core = {
.rc_codes = RC_MAP_TT_1500,
- .allowed_protos = RC_BIT_UNKNOWN,
+ .allowed_protos = RC_BIT_RC5,
.rc_query = pctv452e_rc_query,
.rc_interval = 100,
},
diff --git a/drivers/media/usb/dvb-usb/ttusb2.c b/drivers/media/usb/dvb-usb/ttusb2.c
index 2ce3d19..f107173 100644
--- a/drivers/media/usb/dvb-usb/ttusb2.c
+++ b/drivers/media/usb/dvb-usb/ttusb2.c
@@ -438,9 +438,9 @@
if (rx[8] & 0x01) {
/* got a "press" event */
- st->last_rc_key = (rx[3] << 8) | rx[2];
+ st->last_rc_key = RC_SCANCODE_RC5(rx[3], rx[2]);
deb_info("%s: cmd=0x%02x sys=0x%02x\n", __func__, rx[2], rx[3]);
- rc_keydown(d->rc_dev, st->last_rc_key, rx[1]);
+ rc_keydown(d->rc_dev, RC_TYPE_RC5, st->last_rc_key, rx[1]);
} else if (st->last_rc_key) {
rc_keyup(d->rc_dev);
st->last_rc_key = 0;
@@ -747,7 +747,7 @@
.rc_interval = 150, /* Less than IR_KEYPRESS_TIMEOUT */
.rc_codes = RC_MAP_TT_1500,
.rc_query = tt3650_rc_query,
- .allowed_protos = RC_BIT_UNKNOWN,
+ .allowed_protos = RC_BIT_RC5,
},
.num_adapters = 1,
diff --git a/drivers/media/usb/em28xx/em28xx-input.c b/drivers/media/usb/em28xx/em28xx-input.c
index 56ef49d..7f06ae5 100644
--- a/drivers/media/usb/em28xx/em28xx-input.c
+++ b/drivers/media/usb/em28xx/em28xx-input.c
@@ -27,6 +27,7 @@
#include <linux/interrupt.h>
#include <linux/usb.h>
#include <linux/slab.h>
+#include <linux/bitrev.h>
#include "em28xx.h"
@@ -53,6 +54,7 @@
unsigned int toggle_bit:1;
unsigned int read_count:7;
+ enum rc_type protocol;
u32 scancode;
};
@@ -72,7 +74,7 @@
/* i2c slave address of external device (if used) */
u16 i2c_dev_addr;
- int (*get_key_i2c)(struct i2c_client *, u32 *);
+ int (*get_key_i2c)(struct i2c_client *ir, enum rc_type *protocol, u32 *scancode);
int (*get_key)(struct em28xx_IR *, struct em28xx_ir_poll_result *);
};
@@ -80,7 +82,8 @@
I2C IR based get keycodes - should be used with ir-kbd-i2c
**********************************************************/
-static int em28xx_get_key_terratec(struct i2c_client *i2c_dev, u32 *ir_key)
+static int em28xx_get_key_terratec(struct i2c_client *i2c_dev,
+ enum rc_type *protocol, u32 *scancode)
{
unsigned char b;
@@ -98,14 +101,15 @@
/* keep old data */
return 1;
- *ir_key = b;
+ *protocol = RC_TYPE_UNKNOWN;
+ *scancode = b;
return 1;
}
-static int em28xx_get_key_em_haup(struct i2c_client *i2c_dev, u32 *ir_key)
+static int em28xx_get_key_em_haup(struct i2c_client *i2c_dev,
+ enum rc_type *protocol, u32 *scancode)
{
unsigned char buf[2];
- u16 code;
int size;
/* poll IR chip */
@@ -127,26 +131,13 @@
* So, the code translation is not complete. Yet, it is enough to
* work with the provided RC5 IR.
*/
- code =
- ((buf[0] & 0x01) ? 0x0020 : 0) | /* 0010 0000 */
- ((buf[0] & 0x02) ? 0x0010 : 0) | /* 0001 0000 */
- ((buf[0] & 0x04) ? 0x0008 : 0) | /* 0000 1000 */
- ((buf[0] & 0x08) ? 0x0004 : 0) | /* 0000 0100 */
- ((buf[0] & 0x10) ? 0x0002 : 0) | /* 0000 0010 */
- ((buf[0] & 0x20) ? 0x0001 : 0) | /* 0000 0001 */
- ((buf[1] & 0x08) ? 0x1000 : 0) | /* 0001 0000 */
- ((buf[1] & 0x10) ? 0x0800 : 0) | /* 0000 1000 */
- ((buf[1] & 0x20) ? 0x0400 : 0) | /* 0000 0100 */
- ((buf[1] & 0x40) ? 0x0200 : 0) | /* 0000 0010 */
- ((buf[1] & 0x80) ? 0x0100 : 0); /* 0000 0001 */
-
- /* return key */
- *ir_key = code;
+ *protocol = RC_TYPE_RC5;
+ *scancode = (bitrev8(buf[1]) & 0x1f) << 8 | bitrev8(buf[0]) >> 2;
return 1;
}
static int em28xx_get_key_pinnacle_usb_grey(struct i2c_client *i2c_dev,
- u32 *ir_key)
+ enum rc_type *protocol, u32 *scancode)
{
unsigned char buf[3];
@@ -158,13 +149,13 @@
if (buf[0] != 0x00)
return 0;
- *ir_key = buf[2]&0x3f;
-
+ *protocol = RC_TYPE_UNKNOWN;
+ *scancode = buf[2] & 0x3f;
return 1;
}
static int em28xx_get_key_winfast_usbii_deluxe(struct i2c_client *i2c_dev,
- u32 *ir_key)
+ enum rc_type *protocol, u32 *scancode)
{
unsigned char subaddr, keydetect, key;
@@ -184,7 +175,8 @@
if (key == 0x00)
return 0;
- *ir_key = key;
+ *protocol = RC_TYPE_UNKNOWN;
+ *scancode = key;
return 1;
}
@@ -215,7 +207,22 @@
poll_result->read_count = (msg[0] & 0x7f);
/* Remote Control Address/Data (Regs 0x46/0x47) */
- poll_result->scancode = msg[1] << 8 | msg[2];
+ switch (ir->rc_type) {
+ case RC_BIT_RC5:
+ poll_result->protocol = RC_TYPE_RC5;
+ poll_result->scancode = RC_SCANCODE_RC5(msg[1], msg[2]);
+ break;
+
+ case RC_BIT_NEC:
+ poll_result->protocol = RC_TYPE_NEC;
+ poll_result->scancode = RC_SCANCODE_NEC(msg[1], msg[2]);
+ break;
+
+ default:
+ poll_result->protocol = RC_TYPE_UNKNOWN;
+ poll_result->scancode = msg[1] << 8 | msg[2];
+ break;
+ }
return 0;
}
@@ -247,25 +254,32 @@
*/
switch (ir->rc_type) {
case RC_BIT_RC5:
- poll_result->scancode = msg[1] << 8 | msg[2];
+ poll_result->protocol = RC_TYPE_RC5;
+ poll_result->scancode = RC_SCANCODE_RC5(msg[1], msg[2]);
break;
+
case RC_BIT_NEC:
- if ((msg[3] ^ msg[4]) != 0xff) /* 32 bits NEC */
- poll_result->scancode = (msg[1] << 24) |
- (msg[2] << 16) |
- (msg[3] << 8) |
- msg[4];
- else if ((msg[1] ^ msg[2]) != 0xff) /* 24 bits NEC */
- poll_result->scancode = (msg[1] << 16) |
- (msg[2] << 8) |
- msg[3];
- else /* Normal NEC */
- poll_result->scancode = msg[1] << 8 | msg[3];
- break;
- case RC_BIT_RC6_0:
+ poll_result->protocol = RC_TYPE_RC5;
poll_result->scancode = msg[1] << 8 | msg[2];
+ if ((msg[3] ^ msg[4]) != 0xff) /* 32 bits NEC */
+ poll_result->scancode = RC_SCANCODE_NEC32((msg[1] << 24) |
+ (msg[2] << 16) |
+ (msg[3] << 8) |
+ (msg[4]));
+ else if ((msg[1] ^ msg[2]) != 0xff) /* 24 bits NEC */
+ poll_result->scancode = RC_SCANCODE_NECX(msg[1] << 8 |
+ msg[2], msg[3]);
+ else /* Normal NEC */
+ poll_result->scancode = RC_SCANCODE_NEC(msg[1], msg[3]);
break;
+
+ case RC_BIT_RC6_0:
+ poll_result->protocol = RC_TYPE_RC6_0;
+ poll_result->scancode = RC_SCANCODE_RC6_0(msg[1], msg[2]);
+ break;
+
default:
+ poll_result->protocol = RC_TYPE_UNKNOWN;
poll_result->scancode = (msg[1] << 24) | (msg[2] << 16) |
(msg[3] << 8) | msg[4];
break;
@@ -281,22 +295,24 @@
static int em28xx_i2c_ir_handle_key(struct em28xx_IR *ir)
{
struct em28xx *dev = ir->dev;
- static u32 ir_key;
+ static u32 scancode;
+ enum rc_type protocol;
int rc;
struct i2c_client client;
client.adapter = &ir->dev->i2c_adap[dev->def_i2c_bus];
client.addr = ir->i2c_dev_addr;
- rc = ir->get_key_i2c(&client, &ir_key);
+ rc = ir->get_key_i2c(&client, &protocol, &scancode);
if (rc < 0) {
dprintk("ir->get_key_i2c() failed: %d\n", rc);
return rc;
}
if (rc) {
- dprintk("%s: keycode = 0x%04x\n", __func__, ir_key);
- rc_keydown(ir->rc, ir_key, 0);
+ dprintk("%s: proto = 0x%04x, scancode = 0x%04x\n",
+ __func__, protocol, scancode);
+ rc_keydown(ir->rc, protocol, scancode, 0);
}
return 0;
}
@@ -319,10 +335,12 @@
poll_result.scancode);
if (ir->full_code)
rc_keydown(ir->rc,
+ poll_result.protocol,
poll_result.scancode,
poll_result.toggle_bit);
else
rc_keydown(ir->rc,
+ RC_TYPE_UNKNOWN,
poll_result.scancode & 0xff,
poll_result.toggle_bit);
diff --git a/drivers/media/usb/tm6000/tm6000-input.c b/drivers/media/usb/tm6000/tm6000-input.c
index d1af543..676c0232 100644
--- a/drivers/media/usb/tm6000/tm6000-input.c
+++ b/drivers/media/usb/tm6000/tm6000-input.c
@@ -162,11 +162,42 @@
return 0;
}
+static void tm6000_ir_keydown(struct tm6000_IR *ir,
+ const char *buf, unsigned int len)
+{
+ u8 device, command;
+ u32 scancode;
+ enum rc_type protocol;
+
+ if (len < 1)
+ return;
+
+ command = buf[0];
+ device = (len > 1 ? buf[1] : 0x0);
+ switch (ir->rc_type) {
+ case RC_BIT_RC5:
+ protocol = RC_TYPE_RC5;
+ scancode = RC_SCANCODE_RC5(device, command);
+ break;
+ case RC_BIT_NEC:
+ protocol = RC_TYPE_NEC;
+ scancode = RC_SCANCODE_NEC(device, command);
+ break;
+ default:
+ protocol = RC_TYPE_OTHER;
+ scancode = RC_SCANCODE_OTHER(device << 8 | command);
+ break;
+ }
+
+ dprintk(1, "%s, protocol: 0x%04x, scancode: 0x%08x\n",
+ __func__, protocol, scancode);
+ rc_keydown(ir->rc, protocol, scancode, 0);
+}
+
static void tm6000_ir_urb_received(struct urb *urb)
{
struct tm6000_core *dev = urb->context;
struct tm6000_IR *ir = dev->ir;
- struct tm6000_ir_poll_result poll_result;
char *buf;
dprintk(2, "%s\n",__func__);
@@ -184,12 +215,7 @@
DUMP_PREFIX_OFFSET,16, 1,
buf, urb->actual_length, false);
- poll_result.rc_data = buf[0];
- if (urb->actual_length > 1)
- poll_result.rc_data |= buf[1] << 8;
-
- dprintk(1, "%s, scancode: 0x%04x\n",__func__, poll_result.rc_data);
- rc_keydown(ir->rc, poll_result.rc_data, 0);
+ tm6000_ir_keydown(ir, urb->transfer_buffer, urb->actual_length);
usb_submit_urb(urb, GFP_ATOMIC);
/*
@@ -204,7 +230,6 @@
{
struct tm6000_IR *ir = container_of(work, struct tm6000_IR, work.work);
struct tm6000_core *dev = ir->dev;
- struct tm6000_ir_poll_result poll_result;
int rc;
u8 buf[2];
@@ -219,13 +244,8 @@
if (rc < 0)
return;
- if (rc > 1)
- poll_result.rc_data = buf[0] | buf[1] << 8;
- else
- poll_result.rc_data = buf[0];
-
/* Check if something was read */
- if ((poll_result.rc_data & 0xff) == 0xff) {
+ if ((buf[0] & 0xff) == 0xff) {
if (!ir->pwled) {
tm6000_flash_led(dev, 1);
ir->pwled = 1;
@@ -233,8 +253,7 @@
return;
}
- dprintk(1, "%s, scancode: 0x%04x\n",__func__, poll_result.rc_data);
- rc_keydown(ir->rc, poll_result.rc_data, 0);
+ tm6000_ir_keydown(ir, buf, rc);
tm6000_flash_led(dev, 0);
ir->pwled = 0;