drivers/rtc/Kconfig - kernel/msm-4.9 - Gitiles

 #
 # RTC class/drivers configuration
 #

 config RTC_LIB
 	tristate

 menuconfig RTC_CLASS
 	tristate "Real Time Clock"
 	default n
 	depends on !S390
 	select RTC_LIB
 	help
 	  Generic RTC class support. If you say yes here, you will
  	  be allowed to plug one or more RTCs to your system. You will
 	  probably want to enable one or more of the interfaces below.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-core.

 if RTC_CLASS

 if GEN_RTC || RTC
 comment "Conflicting RTC option has been selected, check GEN_RTC and RTC"
 endif

 config RTC_HCTOSYS
 	bool "Set system time from RTC on startup and resume"
 	depends on RTC_CLASS = y
 	default y
 	help
 	  If you say yes here, the system time (wall clock) will be set using
 	  the value read from a specified RTC device. This is useful to avoid
 	  unnecessary fsck runs at boot time, and to network better.

 config RTC_HCTOSYS_DEVICE
 	string "RTC used to set the system time"
 	depends on RTC_HCTOSYS = y
 	default "rtc0"
 	help
 	  The RTC device that will be used to (re)initialize the system
 	  clock, usually rtc0.  Initialization is done when the system
 	  starts up, and when it resumes from a low power state.  This
 	  device should record time in UTC, since the kernel won't do
 	  timezone correction.

 	  The driver for this RTC device must be loaded before late_initcall
 	  functions run, so it must usually be statically linked.

 	  This clock should be battery-backed, so that it reads the correct
 	  time when the system boots from a power-off state.  Otherwise, your
 	  system will need an external clock source (like an NTP server).

 	  If the clock you specify here is not battery backed, it may still
 	  be useful to reinitialize system time when resuming from system
 	  sleep states. Do not specify an RTC here unless it stays powered
 	  during all this system's supported sleep states.

 config RTC_DEBUG
 	bool "RTC debug support"
 	depends on RTC_CLASS = y
 	help
 	  Say yes here to enable debugging support in the RTC framework
 	  and individual RTC drivers.

 comment "RTC interfaces"

 config RTC_INTF_SYSFS
 	boolean "/sys/class/rtc/rtcN (sysfs)"
 	depends on SYSFS
 	default RTC_CLASS
 	help
 	  Say yes here if you want to use your RTCs using sysfs interfaces,
 	  /sys/class/rtc/rtc0 through /sys/.../rtcN.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-sysfs.

 config RTC_INTF_PROC
 	boolean "/proc/driver/rtc (procfs for rtc0)"
 	depends on PROC_FS
 	default RTC_CLASS
 	help
 	  Say yes here if you want to use your first RTC through the proc
 	  interface, /proc/driver/rtc.  Other RTCs will not be available
 	  through that API.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-proc.

 config RTC_INTF_DEV
 	boolean "/dev/rtcN (character devices)"
 	default RTC_CLASS
 	help
 	  Say yes here if you want to use your RTCs using the /dev
 	  interfaces, which "udev" sets up as /dev/rtc0 through
 	  /dev/rtcN.  You may want to set up a symbolic link so one
 	  of these can be accessed as /dev/rtc, which is a name
 	  expected by "hwclock" and some other programs.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-dev.

 config RTC_INTF_DEV_UIE_EMUL
 	bool "RTC UIE emulation on dev interface"
 	depends on RTC_INTF_DEV
 	help
 	  Provides an emulation for RTC_UIE if the underlying rtc chip
 	  driver does not expose RTC_UIE ioctls.  Those requests generate
 	  once-per-second update interrupts, used for synchronization.

 config RTC_DRV_TEST
 	tristate "Test driver/device"
 	help
 	  If you say yes here you get support for the
 	  RTC test driver. It's a software RTC which can be
 	  used to test the RTC subsystem APIs. It gets
 	  the time from the system clock.
 	  You want this driver only if you are doing development
 	  on the RTC subsystem. Please read the source code
 	  for further details.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-test.

 comment "I2C RTC drivers"
 	depends on I2C

 if I2C

 config RTC_DRV_DS1307
 	tristate "Dallas/Maxim DS1307/37/38/39/40, ST M41T00"
 	help
 	  If you say yes here you get support for various compatible RTC
 	  chips (often with battery backup) connected with I2C.  This driver
 	  should handle DS1307, DS1337, DS1338, DS1339, DS1340, ST M41T00,
 	  and probably other chips.  In some cases the RTC must already
 	  have been initialized (by manufacturing or a bootloader).

 	  The first seven registers on these chips hold an RTC, and other
 	  registers may add features such as NVRAM, a trickle charger for
 	  the RTC/NVRAM backup power, and alarms.  NVRAM is visible in
 	  sysfs, but other chip features may not be available.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-ds1307.

 config RTC_DRV_DS1374
 	tristate "Dallas/Maxim DS1374"
 	depends on RTC_CLASS && I2C
 	help
 	  If you say yes here you get support for Dallas Semiconductor
 	  DS1374 real-time clock chips.  If an interrupt is associated
 	  with the device, the alarm functionality is supported.

 	  This driver can also be built as a module.  If so, the module
 	  will be called rtc-ds1374.

 config RTC_DRV_DS1672
 	tristate "Dallas/Maxim DS1672"
 	help
 	  If you say yes here you get support for the
 	  Dallas/Maxim DS1672 timekeeping chip.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-ds1672.

 config RTC_DRV_MAX6900
 	tristate "Maxim MAX6900"
 	help
 	  If you say yes here you will get support for the
 	  Maxim MAX6900 I2C RTC chip.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-max6900.

 config RTC_DRV_RS5C372
 	tristate "Ricoh RS5C372A/B, RV5C386, RV5C387A"
 	help
 	  If you say yes here you get support for the
 	  Ricoh RS5C372A, RS5C372B, RV5C386, and RV5C387A RTC chips.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-rs5c372.

 config RTC_DRV_ISL1208
 	tristate "Intersil ISL1208"
 	help
 	  If you say yes here you get support for the
 	  Intersil ISL1208 RTC chip.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-isl1208.

 config RTC_DRV_X1205
 	tristate "Xicor/Intersil X1205"
 	help
 	  If you say yes here you get support for the
 	  Xicor/Intersil X1205 RTC chip.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-x1205.

 config RTC_DRV_PCF8563
 	tristate "Philips PCF8563/Epson RTC8564"
 	help
 	  If you say yes here you get support for the
 	  Philips PCF8563 RTC chip. The Epson RTC8564
 	  should work as well.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-pcf8563.

 config RTC_DRV_PCF8583
 	tristate "Philips PCF8583"
 	help
 	  If you say yes here you get support for the Philips PCF8583
 	  RTC chip found on Acorn RiscPCs. This driver supports the
 	  platform specific method of retrieving the current year from
 	  the RTC's SRAM. It will work on other platforms with the same
 	  chip, but the year will probably have to be tweaked.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-pcf8583.

 config RTC_DRV_M41T80
 	tristate "ST M41T80/81/82/83/84/85/87"
 	help
 	  If you say Y here you will get support for the
 	  ST M41T80 RTC chips series. Currently following chips are
 	  supported: M41T80, M41T81, M41T82, M41T83, M41ST84, M41ST85
 	  and M41ST87.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-m41t80.

 config RTC_DRV_M41T80_WDT
 	bool "ST M41T80 series RTC watchdog timer"
 	depends on RTC_DRV_M41T80
 	help
 	  If you say Y here you will get support for the
 	  watchdog timer in ST M41T80 RTC chips series.

 config RTC_DRV_TWL92330
 	boolean "TI TWL92330/Menelaus"
 	depends on MENELAUS
 	help
 	  If you say yes here you get support for the RTC on the
 	  TWL92330 "Menelaus" power management chip, used with OMAP2
 	  platforms.  The support is integrated with the rest of
 	  the Menelaus driver; it's not separate module.

 config RTC_DRV_S35390A
 	tristate "Seiko Instruments S-35390A"
 	select BITREVERSE
 	help
 	  If you say yes here you will get support for the Seiko
 	  Instruments S-35390A.

 	  This driver can also be built as a module. If so the module
 	  will be called rtc-s35390a.

 endif # I2C

 comment "SPI RTC drivers"

 if SPI_MASTER

 config RTC_DRV_MAX6902
 	tristate "Maxim MAX6902"
 	help
 	  If you say yes here you will get support for the
 	  Maxim MAX6902 SPI RTC chip.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-max6902.

 config RTC_DRV_R9701
 	tristate "Epson RTC-9701JE"
 	help
 	  If you say yes here you will get support for the
 	  Epson RTC-9701JE SPI RTC chip.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-r9701.

 config RTC_DRV_RS5C348
 	tristate "Ricoh RS5C348A/B"
 	help
 	  If you say yes here you get support for the
 	  Ricoh RS5C348A and RS5C348B RTC chips.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-rs5c348.

 endif # SPI_MASTER

 comment "Platform RTC drivers"

 # this 'CMOS' RTC driver is arch dependent because <asm-generic/rtc.h>
 # requires <asm/mc146818rtc.h> defining CMOS_READ/CMOS_WRITE, and a
 # global rtc_lock ... it's not yet just another platform_device.

 config RTC_DRV_CMOS
 	tristate "PC-style 'CMOS'"
 	depends on X86 || ALPHA || ARM || M32R || ATARI || PPC || MIPS
 	help
 	  Say "yes" here to get direct support for the real time clock
 	  found in every PC or ACPI-based system, and some other boards.
 	  Specifically the original MC146818, compatibles like those in
 	  PC south bridges, the DS12887 or M48T86, some multifunction
 	  or LPC bus chips, and so on.

 	  Your system will need to define the platform device used by
 	  this driver, otherwise it won't be accessible.  This means
 	  you can safely enable this driver if you don't know whether
 	  or not your board has this kind of hardware.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-cmos.

 config RTC_DRV_DS1216
 	tristate "Dallas DS1216"
 	depends on SNI_RM
 	help
 	  If you say yes here you get support for the Dallas DS1216 RTC chips.

 config RTC_DRV_DS1302
 	tristate "Dallas DS1302"
 	depends on SH_SECUREEDGE5410
 	help
 	  If you say yes here you get support for the Dallas DS1302 RTC chips.

 config RTC_DRV_DS1511
 	tristate "Dallas DS1511"
 	depends on RTC_CLASS
 	help
 	  If you say yes here you get support for the
 	  Dallas DS1511 timekeeping/watchdog chip.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-ds1511.

 config RTC_DRV_DS1553
 	tristate "Maxim/Dallas DS1553"
 	help
 	  If you say yes here you get support for the
 	  Maxim/Dallas DS1553 timekeeping chip.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-ds1553.

 config RTC_DRV_DS1742
 	tristate "Maxim/Dallas DS1742/1743"
 	help
 	  If you say yes here you get support for the
 	  Maxim/Dallas DS1742/1743 timekeeping chip.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-ds1742.

 config RTC_DRV_STK17TA8
 	tristate "Simtek STK17TA8"
 	depends on RTC_CLASS
 	help
 	  If you say yes here you get support for the
 	  Simtek STK17TA8 timekeeping chip.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-stk17ta8.

 config RTC_DRV_M48T86
 	tristate "ST M48T86/Dallas DS12887"
 	help
 	  If you say Y here you will get support for the
 	  ST M48T86 and Dallas DS12887 RTC chips.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-m48t86.

 config RTC_DRV_M48T59
 	tristate "ST M48T59"
 	help
 	  If you say Y here you will get support for the
 	  ST M48T59 RTC chip.

 	  This driver can also be built as a module, if so, the module
 	  will be called "rtc-m48t59".

 config RTC_DRV_V3020
 	tristate "EM Microelectronic V3020"
 	help
 	  If you say yes here you will get support for the
 	  EM Microelectronic v3020 RTC chip.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-v3020.

 comment "on-CPU RTC drivers"

 config RTC_DRV_OMAP
 	tristate "TI OMAP1"
 	depends on ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730
 	help
 	  Say "yes" here to support the real time clock on TI OMAP1 chips.
 	  This driver can also be built as a module called rtc-omap.

 config RTC_DRV_S3C
 	tristate "Samsung S3C series SoC RTC"
 	depends on ARCH_S3C2410
 	help
 	  RTC (Realtime Clock) driver for the clock inbuilt into the
 	  Samsung S3C24XX series of SoCs. This can provide periodic
 	  interrupt rates from 1Hz to 64Hz for user programs, and
 	  wakeup from Alarm.

 	  The driver currently supports the common features on all the
 	  S3C24XX range, such as the S3C2410, S3C2412, S3C2413, S3C2440
 	  and S3C2442.

 	  This driver can also be build as a module. If so, the module
 	  will be called rtc-s3c.

 config RTC_DRV_EP93XX
 	tristate "Cirrus Logic EP93XX"
 	depends on ARCH_EP93XX
 	help
 	  If you say yes here you get support for the
 	  RTC embedded in the Cirrus Logic EP93XX processors.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-ep93xx.

 config RTC_DRV_SA1100
 	tristate "SA11x0/PXA2xx"
 	depends on ARCH_SA1100 || ARCH_PXA
 	help
 	  If you say Y here you will get access to the real time clock
 	  built into your SA11x0 or PXA2xx CPU.

 	  To compile this driver as a module, choose M here: the
 	  module will be called rtc-sa1100.

 config RTC_DRV_SH
 	tristate "SuperH On-Chip RTC"
 	depends on RTC_CLASS && SUPERH
 	help
 	  Say Y here to enable support for the on-chip RTC found in
 	  most SuperH processors.

  	  To compile this driver as a module, choose M here: the
 	  module will be called rtc-sh.

 config RTC_DRV_VR41XX
 	tristate "NEC VR41XX"
 	depends on CPU_VR41XX
 	help
 	  If you say Y here you will get access to the real time clock
 	  built into your NEC VR41XX CPU.

 	  To compile this driver as a module, choose M here: the
 	  module will be called rtc-vr41xx.

 config RTC_DRV_PL031
 	tristate "ARM AMBA PL031 RTC"
 	depends on ARM_AMBA
 	help
 	  If you say Y here you will get access to ARM AMBA
 	  PrimeCell PL031 RTC found on certain ARM SOCs.

 	  To compile this driver as a module, choose M here: the
 	  module will be called rtc-pl031.

 config RTC_DRV_AT32AP700X
 	tristate "AT32AP700X series RTC"
 	depends on PLATFORM_AT32AP
 	help
 	  Driver for the internal RTC (Realtime Clock) on Atmel AVR32
 	  AT32AP700x family processors.

 config RTC_DRV_AT91RM9200
 	tristate "AT91RM9200 or AT91SAM9RL"
 	depends on ARCH_AT91RM9200 || ARCH_AT91SAM9RL
 	help
 	  Driver for the internal RTC (Realtime Clock) module found on
 	  Atmel AT91RM9200's and AT91SAM9RL chips.  On SAM9RL chips
 	  this is powered by the backup power supply.

 config RTC_DRV_AT91SAM9
 	tristate "AT91SAM9x"
 	depends on ARCH_AT91 && !(ARCH_AT91RM9200 || ARCH_AT91X40)
 	help
 	  RTC driver for the Atmel AT91SAM9x internal RTT (Real Time Timer).
 	  These timers are powered by the backup power supply (such as a
 	  small coin cell battery), but do not need to be used as RTCs.

 	  (On AT91SAM9rl chips you probably want to use the dedicated RTC
 	  module and leave the RTT available for other uses.)

 config RTC_DRV_AT91SAM9_RTT
 	int
 	range 0 1
 	default 0
 	prompt "RTT module Number" if ARCH_AT91SAM9263
 	depends on RTC_DRV_AT91SAM9
 	help
 	  More than one RTT module is available.  You can choose which
 	  one will be used as an RTC.  The default of zero is normally
 	  OK to use, though some systems use that for non-RTC purposes.

 config RTC_DRV_AT91SAM9_GPBR
 	int
 	range 0 3 if !ARCH_AT91SAM9263
 	range 0 15 if ARCH_AT91SAM9263
 	default 0
 	prompt "Backup Register Number"
 	depends on RTC_DRV_AT91SAM9
 	help
 	  The RTC driver needs to use one of the General Purpose Backup
 	  Registers (GPBRs) as well as the RTT.  You can choose which one
 	  will be used.  The default of zero is normally OK to use, but
 	  on some systems other software needs to use that register.

 config RTC_DRV_BFIN
 	tristate "Blackfin On-Chip RTC"
 	depends on BLACKFIN
 	help
 	  If you say yes here you will get support for the
 	  Blackfin On-Chip Real Time Clock.

 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-bfin.

 config RTC_DRV_RS5C313
 	tristate "Ricoh RS5C313"
 	depends on SH_LANDISK
 	help
 	  If you say yes here you get support for the Ricoh RS5C313 RTC chips.

 endif # RTC_CLASS
	#
	# RTC class/drivers configuration
	#

	config RTC_LIB
	tristate

	menuconfig RTC_CLASS
	tristate "Real Time Clock"
	default n
	depends on !S390
	select RTC_LIB
	help
	Generic RTC class support. If you say yes here, you will
	be allowed to plug one or more RTCs to your system. You will
	probably want to enable one or more of the interfaces below.

	This driver can also be built as a module. If so, the module
	will be called rtc-core.

	if RTC_CLASS

	if GEN_RTC \|\| RTC
	comment "Conflicting RTC option has been selected, check GEN_RTC and RTC"
	endif

	config RTC_HCTOSYS
	bool "Set system time from RTC on startup and resume"
	depends on RTC_CLASS = y
	default y
	help
	If you say yes here, the system time (wall clock) will be set using
	the value read from a specified RTC device. This is useful to avoid
	unnecessary fsck runs at boot time, and to network better.

	config RTC_HCTOSYS_DEVICE
	string "RTC used to set the system time"
	depends on RTC_HCTOSYS = y
	default "rtc0"
	help
	The RTC device that will be used to (re)initialize the system
	clock, usually rtc0. Initialization is done when the system
	starts up, and when it resumes from a low power state. This
	device should record time in UTC, since the kernel won't do
	timezone correction.

	The driver for this RTC device must be loaded before late_initcall
	functions run, so it must usually be statically linked.

	This clock should be battery-backed, so that it reads the correct
	time when the system boots from a power-off state. Otherwise, your
	system will need an external clock source (like an NTP server).

	If the clock you specify here is not battery backed, it may still
	be useful to reinitialize system time when resuming from system
	sleep states. Do not specify an RTC here unless it stays powered
	during all this system's supported sleep states.

	config RTC_DEBUG
	bool "RTC debug support"
	depends on RTC_CLASS = y
	help
	Say yes here to enable debugging support in the RTC framework
	and individual RTC drivers.

	comment "RTC interfaces"

	config RTC_INTF_SYSFS
	boolean "/sys/class/rtc/rtcN (sysfs)"
	depends on SYSFS
	default RTC_CLASS
	help
	Say yes here if you want to use your RTCs using sysfs interfaces,
	/sys/class/rtc/rtc0 through /sys/.../rtcN.

	This driver can also be built as a module. If so, the module
	will be called rtc-sysfs.

	config RTC_INTF_PROC
	boolean "/proc/driver/rtc (procfs for rtc0)"
	depends on PROC_FS
	default RTC_CLASS
	help
	Say yes here if you want to use your first RTC through the proc
	interface, /proc/driver/rtc. Other RTCs will not be available
	through that API.

	This driver can also be built as a module. If so, the module
	will be called rtc-proc.

	config RTC_INTF_DEV
	boolean "/dev/rtcN (character devices)"
	default RTC_CLASS
	help
	Say yes here if you want to use your RTCs using the /dev
	interfaces, which "udev" sets up as /dev/rtc0 through
	/dev/rtcN. You may want to set up a symbolic link so one
	of these can be accessed as /dev/rtc, which is a name
	expected by "hwclock" and some other programs.

	This driver can also be built as a module. If so, the module
	will be called rtc-dev.

	config RTC_INTF_DEV_UIE_EMUL
	bool "RTC UIE emulation on dev interface"
	depends on RTC_INTF_DEV
	help
	Provides an emulation for RTC_UIE if the underlying rtc chip
	driver does not expose RTC_UIE ioctls. Those requests generate
	once-per-second update interrupts, used for synchronization.

	config RTC_DRV_TEST
	tristate "Test driver/device"
	help
	If you say yes here you get support for the
	RTC test driver. It's a software RTC which can be
	used to test the RTC subsystem APIs. It gets
	the time from the system clock.
	You want this driver only if you are doing development
	on the RTC subsystem. Please read the source code
	for further details.

	This driver can also be built as a module. If so, the module
	will be called rtc-test.

	comment "I2C RTC drivers"
	depends on I2C

	if I2C

	config RTC_DRV_DS1307
	tristate "Dallas/Maxim DS1307/37/38/39/40, ST M41T00"
	help
	If you say yes here you get support for various compatible RTC
	chips (often with battery backup) connected with I2C. This driver
	should handle DS1307, DS1337, DS1338, DS1339, DS1340, ST M41T00,
	and probably other chips. In some cases the RTC must already
	have been initialized (by manufacturing or a bootloader).

	The first seven registers on these chips hold an RTC, and other
	registers may add features such as NVRAM, a trickle charger for
	the RTC/NVRAM backup power, and alarms. NVRAM is visible in
	sysfs, but other chip features may not be available.

	This driver can also be built as a module. If so, the module
	will be called rtc-ds1307.

	config RTC_DRV_DS1374
	tristate "Dallas/Maxim DS1374"
	depends on RTC_CLASS && I2C
	help
	If you say yes here you get support for Dallas Semiconductor
	DS1374 real-time clock chips. If an interrupt is associated
	with the device, the alarm functionality is supported.

	This driver can also be built as a module. If so, the module
	will be called rtc-ds1374.

	config RTC_DRV_DS1672
	tristate "Dallas/Maxim DS1672"
	help
	If you say yes here you get support for the
	Dallas/Maxim DS1672 timekeeping chip.

	This driver can also be built as a module. If so, the module
	will be called rtc-ds1672.

	config RTC_DRV_MAX6900
	tristate "Maxim MAX6900"
	help
	If you say yes here you will get support for the
	Maxim MAX6900 I2C RTC chip.

	This driver can also be built as a module. If so, the module
	will be called rtc-max6900.

	config RTC_DRV_RS5C372
	tristate "Ricoh RS5C372A/B, RV5C386, RV5C387A"
	help
	If you say yes here you get support for the
	Ricoh RS5C372A, RS5C372B, RV5C386, and RV5C387A RTC chips.

	This driver can also be built as a module. If so, the module
	will be called rtc-rs5c372.

	config RTC_DRV_ISL1208
	tristate "Intersil ISL1208"
	help
	If you say yes here you get support for the
	Intersil ISL1208 RTC chip.

	This driver can also be built as a module. If so, the module
	will be called rtc-isl1208.

	config RTC_DRV_X1205
	tristate "Xicor/Intersil X1205"
	help
	If you say yes here you get support for the
	Xicor/Intersil X1205 RTC chip.

	This driver can also be built as a module. If so, the module
	will be called rtc-x1205.

	config RTC_DRV_PCF8563
	tristate "Philips PCF8563/Epson RTC8564"
	help
	If you say yes here you get support for the
	Philips PCF8563 RTC chip. The Epson RTC8564
	should work as well.

	This driver can also be built as a module. If so, the module
	will be called rtc-pcf8563.

	config RTC_DRV_PCF8583
	tristate "Philips PCF8583"
	help
	If you say yes here you get support for the Philips PCF8583
	RTC chip found on Acorn RiscPCs. This driver supports the
	platform specific method of retrieving the current year from
	the RTC's SRAM. It will work on other platforms with the same
	chip, but the year will probably have to be tweaked.

	This driver can also be built as a module. If so, the module
	will be called rtc-pcf8583.

	config RTC_DRV_M41T80
	tristate "ST M41T80/81/82/83/84/85/87"
	help
	If you say Y here you will get support for the
	ST M41T80 RTC chips series. Currently following chips are
	supported: M41T80, M41T81, M41T82, M41T83, M41ST84, M41ST85
	and M41ST87.

	This driver can also be built as a module. If so, the module
	will be called rtc-m41t80.

	config RTC_DRV_M41T80_WDT
	bool "ST M41T80 series RTC watchdog timer"
	depends on RTC_DRV_M41T80
	help
	If you say Y here you will get support for the
	watchdog timer in ST M41T80 RTC chips series.

	config RTC_DRV_TWL92330
	boolean "TI TWL92330/Menelaus"
	depends on MENELAUS
	help
	If you say yes here you get support for the RTC on the
	TWL92330 "Menelaus" power management chip, used with OMAP2
	platforms. The support is integrated with the rest of
	the Menelaus driver; it's not separate module.

	config RTC_DRV_S35390A
	tristate "Seiko Instruments S-35390A"
	select BITREVERSE
	help
	If you say yes here you will get support for the Seiko
	Instruments S-35390A.

	This driver can also be built as a module. If so the module
	will be called rtc-s35390a.

	endif # I2C

	comment "SPI RTC drivers"

	if SPI_MASTER

	config RTC_DRV_MAX6902
	tristate "Maxim MAX6902"
	help
	If you say yes here you will get support for the
	Maxim MAX6902 SPI RTC chip.

	This driver can also be built as a module. If so, the module
	will be called rtc-max6902.

	config RTC_DRV_R9701
	tristate "Epson RTC-9701JE"
	help
	If you say yes here you will get support for the
	Epson RTC-9701JE SPI RTC chip.

	This driver can also be built as a module. If so, the module
	will be called rtc-r9701.

	config RTC_DRV_RS5C348
	tristate "Ricoh RS5C348A/B"
	help
	If you say yes here you get support for the
	Ricoh RS5C348A and RS5C348B RTC chips.

	This driver can also be built as a module. If so, the module
	will be called rtc-rs5c348.

	endif # SPI_MASTER

	comment "Platform RTC drivers"

	# this 'CMOS' RTC driver is arch dependent because <asm-generic/rtc.h>
	# requires <asm/mc146818rtc.h> defining CMOS_READ/CMOS_WRITE, and a
	# global rtc_lock ... it's not yet just another platform_device.

	config RTC_DRV_CMOS
	tristate "PC-style 'CMOS'"
	depends on X86 \|\| ALPHA \|\| ARM \|\| M32R \|\| ATARI \|\| PPC \|\| MIPS
	help
	Say "yes" here to get direct support for the real time clock
	found in every PC or ACPI-based system, and some other boards.
	Specifically the original MC146818, compatibles like those in
	PC south bridges, the DS12887 or M48T86, some multifunction
	or LPC bus chips, and so on.

	Your system will need to define the platform device used by
	this driver, otherwise it won't be accessible. This means
	you can safely enable this driver if you don't know whether
	or not your board has this kind of hardware.

	This driver can also be built as a module. If so, the module
	will be called rtc-cmos.

	config RTC_DRV_DS1216
	tristate "Dallas DS1216"
	depends on SNI_RM
	help
	If you say yes here you get support for the Dallas DS1216 RTC chips.

	config RTC_DRV_DS1302
	tristate "Dallas DS1302"
	depends on SH_SECUREEDGE5410
	help
	If you say yes here you get support for the Dallas DS1302 RTC chips.

	config RTC_DRV_DS1511
	tristate "Dallas DS1511"
	depends on RTC_CLASS
	help
	If you say yes here you get support for the
	Dallas DS1511 timekeeping/watchdog chip.

	This driver can also be built as a module. If so, the module
	will be called rtc-ds1511.

	config RTC_DRV_DS1553
	tristate "Maxim/Dallas DS1553"
	help
	If you say yes here you get support for the
	Maxim/Dallas DS1553 timekeeping chip.

	This driver can also be built as a module. If so, the module
	will be called rtc-ds1553.

	config RTC_DRV_DS1742
	tristate "Maxim/Dallas DS1742/1743"
	help
	If you say yes here you get support for the
	Maxim/Dallas DS1742/1743 timekeeping chip.

	This driver can also be built as a module. If so, the module
	will be called rtc-ds1742.

	config RTC_DRV_STK17TA8
	tristate "Simtek STK17TA8"
	depends on RTC_CLASS
	help
	If you say yes here you get support for the
	Simtek STK17TA8 timekeeping chip.

	This driver can also be built as a module. If so, the module
	will be called rtc-stk17ta8.

	config RTC_DRV_M48T86
	tristate "ST M48T86/Dallas DS12887"
	help
	If you say Y here you will get support for the
	ST M48T86 and Dallas DS12887 RTC chips.

	This driver can also be built as a module. If so, the module
	will be called rtc-m48t86.

	config RTC_DRV_M48T59
	tristate "ST M48T59"
	help
	If you say Y here you will get support for the
	ST M48T59 RTC chip.

	This driver can also be built as a module, if so, the module
	will be called "rtc-m48t59".

	config RTC_DRV_V3020
	tristate "EM Microelectronic V3020"
	help
	If you say yes here you will get support for the
	EM Microelectronic v3020 RTC chip.

	This driver can also be built as a module. If so, the module
	will be called rtc-v3020.

	comment "on-CPU RTC drivers"

	config RTC_DRV_OMAP
	tristate "TI OMAP1"
	depends on ARCH_OMAP15XX \|\| ARCH_OMAP16XX \|\| ARCH_OMAP730
	help
	Say "yes" here to support the real time clock on TI OMAP1 chips.
	This driver can also be built as a module called rtc-omap.

	config RTC_DRV_S3C
	tristate "Samsung S3C series SoC RTC"
	depends on ARCH_S3C2410
	help
	RTC (Realtime Clock) driver for the clock inbuilt into the
	Samsung S3C24XX series of SoCs. This can provide periodic
	interrupt rates from 1Hz to 64Hz for user programs, and
	wakeup from Alarm.

	The driver currently supports the common features on all the
	S3C24XX range, such as the S3C2410, S3C2412, S3C2413, S3C2440
	and S3C2442.

	This driver can also be build as a module. If so, the module
	will be called rtc-s3c.

	config RTC_DRV_EP93XX
	tristate "Cirrus Logic EP93XX"
	depends on ARCH_EP93XX
	help
	If you say yes here you get support for the
	RTC embedded in the Cirrus Logic EP93XX processors.

	This driver can also be built as a module. If so, the module
	will be called rtc-ep93xx.

	config RTC_DRV_SA1100
	tristate "SA11x0/PXA2xx"
	depends on ARCH_SA1100 \|\| ARCH_PXA
	help
	If you say Y here you will get access to the real time clock
	built into your SA11x0 or PXA2xx CPU.

	To compile this driver as a module, choose M here: the
	module will be called rtc-sa1100.

	config RTC_DRV_SH
	tristate "SuperH On-Chip RTC"
	depends on RTC_CLASS && SUPERH
	help
	Say Y here to enable support for the on-chip RTC found in
	most SuperH processors.

	To compile this driver as a module, choose M here: the
	module will be called rtc-sh.

	config RTC_DRV_VR41XX
	tristate "NEC VR41XX"
	depends on CPU_VR41XX
	help
	If you say Y here you will get access to the real time clock
	built into your NEC VR41XX CPU.

	To compile this driver as a module, choose M here: the
	module will be called rtc-vr41xx.

	config RTC_DRV_PL031
	tristate "ARM AMBA PL031 RTC"
	depends on ARM_AMBA
	help
	If you say Y here you will get access to ARM AMBA
	PrimeCell PL031 RTC found on certain ARM SOCs.

	To compile this driver as a module, choose M here: the
	module will be called rtc-pl031.

	config RTC_DRV_AT32AP700X
	tristate "AT32AP700X series RTC"
	depends on PLATFORM_AT32AP
	help
	Driver for the internal RTC (Realtime Clock) on Atmel AVR32
	AT32AP700x family processors.

	config RTC_DRV_AT91RM9200
	tristate "AT91RM9200 or AT91SAM9RL"
	depends on ARCH_AT91RM9200 \|\| ARCH_AT91SAM9RL
	help
	Driver for the internal RTC (Realtime Clock) module found on
	Atmel AT91RM9200's and AT91SAM9RL chips. On SAM9RL chips
	this is powered by the backup power supply.

	config RTC_DRV_AT91SAM9
	tristate "AT91SAM9x"
	depends on ARCH_AT91 && !(ARCH_AT91RM9200 \|\| ARCH_AT91X40)
	help
	RTC driver for the Atmel AT91SAM9x internal RTT (Real Time Timer).
	These timers are powered by the backup power supply (such as a
	small coin cell battery), but do not need to be used as RTCs.

	(On AT91SAM9rl chips you probably want to use the dedicated RTC
	module and leave the RTT available for other uses.)

	config RTC_DRV_AT91SAM9_RTT
	int
	range 0 1
	default 0
	prompt "RTT module Number" if ARCH_AT91SAM9263
	depends on RTC_DRV_AT91SAM9
	help
	More than one RTT module is available. You can choose which
	one will be used as an RTC. The default of zero is normally
	OK to use, though some systems use that for non-RTC purposes.

	config RTC_DRV_AT91SAM9_GPBR
	int
	range 0 3 if !ARCH_AT91SAM9263
	range 0 15 if ARCH_AT91SAM9263
	default 0
	prompt "Backup Register Number"
	depends on RTC_DRV_AT91SAM9
	help
	The RTC driver needs to use one of the General Purpose Backup
	Registers (GPBRs) as well as the RTT. You can choose which one
	will be used. The default of zero is normally OK to use, but
	on some systems other software needs to use that register.

	config RTC_DRV_BFIN
	tristate "Blackfin On-Chip RTC"
	depends on BLACKFIN
	help
	If you say yes here you will get support for the
	Blackfin On-Chip Real Time Clock.

	This driver can also be built as a module. If so, the module
	will be called rtc-bfin.

	config RTC_DRV_RS5C313
	tristate "Ricoh RS5C313"
	depends on SH_LANDISK
	help
	If you say yes here you get support for the Ricoh RS5C313 RTC chips.

	endif # RTC_CLASS