| /* |
| * DVB USB Linux driver for the HDIC receiver |
| * |
| * Copyright (C) 2011 Metropolia University of Applied Sciences, Electria R&D |
| * |
| * Author: Antti Palosaari <crope@iki.fi> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. |
| */ |
| |
| #include "hdic.h" |
| #include "hd29l2.h" |
| #include "mxl5007t.h" |
| |
| /* debug */ |
| static int dvb_usb_hdic_debug; |
| module_param_named(debug, dvb_usb_hdic_debug, int, 0644); |
| MODULE_PARM_DESC(debug, "set debugging level" DVB_USB_DEBUG_STATUS); |
| DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr); |
| /* |
| * I2C addresses (7bit) found by probing I2C bus: |
| * 0x48 ?? |
| * 0x51 eeprom |
| * 0x60 MaxLinear MXL5007T tuner |
| * 0x73 HDIC HD29L2 demod |
| * |
| * Xtals: |
| * 24.000 MHz Cypress CY7C68013A-56 (FX2) |
| * 30.400 MHz HDIC HD29L2 |
| * 24.000 MHz MaxLinear MXL5007T |
| * |
| * I/Os: |
| * RDY1 / SLWR == TS_CLK (USB_SLWR = !TS_CLK&TS_VALID) |
| * PA1 / INT1 == 29L1_RESET RST_N |
| */ |
| |
| /* |
| * See Qanu DVB-T USB2.0 communication protocol specification for more |
| * information used USB API. |
| */ |
| |
| /* I2C */ |
| static int hdic_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msg[], |
| int num) |
| { |
| int ret; |
| struct dvb_usb_device *d = i2c_get_adapdata(adap); |
| u8 buf[64]; |
| |
| /* |
| * increase sleep when there is a lot of errors: |
| * dvb-usb: recv bulk message failed: -110 |
| */ |
| #define HDIC_I2C_SLEEP 1 |
| |
| if (mutex_lock_interruptible(&d->i2c_mutex) < 0) |
| return -EAGAIN; |
| |
| if (num == 2 && !(msg[0].flags & I2C_M_RD) && |
| (msg[1].flags & I2C_M_RD)) { |
| /* I2C write + read combination (typical register read) */ |
| buf[0] = HDIC_CMD_I2C; |
| buf[1] = (msg[0].addr << 1); /* I2C write */ |
| buf[2] = msg[0].len; |
| buf[3] = 1; /* no I2C stop => repeated start */ |
| memcpy(&buf[4], msg[0].buf, msg[0].len); |
| ret = dvb_usb_generic_rw(d, buf, 4+msg[0].len, buf, 1, |
| HDIC_I2C_SLEEP); |
| if (ret) |
| goto err; |
| |
| buf[0] = HDIC_CMD_I2C; |
| buf[1] = (msg[1].addr << 1) | 0x01; /* I2C read */ |
| buf[2] = msg[1].len; |
| buf[3] = 0; /* I2C stop */ |
| ret = dvb_usb_generic_rw(d, buf, 4, buf, 1+msg[1].len, |
| HDIC_I2C_SLEEP); |
| if (ret) |
| goto err; |
| |
| memcpy(msg[1].buf, &buf[1], msg[1].len); |
| |
| } else if (num == 1 && !(msg[0].flags & I2C_M_RD)) { |
| /* I2C write (typical register write) */ |
| buf[0] = HDIC_CMD_I2C; |
| buf[1] = (msg[0].addr << 1); /* I2C write */ |
| buf[2] = msg[0].len; |
| buf[3] = 0; /* I2C stop */ |
| memcpy(&buf[4], msg[0].buf, msg[0].len); |
| ret = dvb_usb_generic_rw(d, buf, 4+msg[0].len, buf, 1, |
| HDIC_I2C_SLEEP); |
| if (ret) |
| goto err; |
| } else { |
| ret = -EOPNOTSUPP; |
| goto err; |
| } |
| |
| usleep_range(100, 1000); |
| |
| mutex_unlock(&d->i2c_mutex); |
| |
| return num; |
| |
| err: |
| deb_info("%s: failed=%d\n", __func__, ret); |
| mutex_unlock(&d->i2c_mutex); |
| return ret; |
| } |
| |
| static u32 hdic_i2c_func(struct i2c_adapter *adapter) |
| { |
| return I2C_FUNC_I2C; |
| } |
| |
| static struct i2c_algorithm hdic_i2c_algo = { |
| .master_xfer = hdic_i2c_xfer, |
| .functionality = hdic_i2c_func, |
| }; |
| |
| /* Callbacks for DVB USB */ |
| static int hdic_power_ctrl(struct dvb_usb_device *d, int enable) |
| { |
| u8 sbuf[] = { HDIC_CMD_SLEEP_MODE, enable ? 0 : 1 }; |
| u8 rbuf[1]; |
| |
| deb_info("%s: enable=%d\n", __func__, enable); |
| |
| return dvb_usb_generic_rw(d, sbuf, sizeof(sbuf), rbuf, sizeof(rbuf), 0); |
| } |
| |
| static int hdic_streaming_ctrl(struct dvb_usb_adapter *adap, int enable) |
| { |
| u8 sbuf[] = { HDIC_CMD_CONTROL_STREAM_TRANSFER, enable }; |
| u8 rbuf[1]; |
| |
| deb_info("%s: enable=%d\n", __func__, enable); |
| |
| return dvb_usb_generic_rw(adap->dev, sbuf, sizeof(sbuf), rbuf, |
| sizeof(rbuf), 0); |
| } |
| |
| /* general callback */ |
| static int hdic_frontend_callback(void *priv, int component, int cmd, int arg) |
| { |
| int ret; |
| struct dvb_frontend *fe = priv; |
| struct dvb_usb_adapter *adap = fe->dvb->priv; |
| u8 sbuf[2] = { HDIC_CMD_DEMOD_RESET }; |
| u8 rbuf[1]; |
| |
| deb_info("%s:\n", __func__); |
| |
| /* enable demod reset */ |
| sbuf[1] = 1; |
| ret = dvb_usb_generic_rw(adap->dev, sbuf, sizeof(sbuf), |
| rbuf, sizeof(rbuf), 0); |
| if (ret) |
| deb_info("%s: failed enable demod reset\n", __func__); |
| |
| usleep_range(100, 10000); |
| |
| /* disable demod reset */ |
| sbuf[1] = 0; |
| ret = dvb_usb_generic_rw(adap->dev, sbuf, sizeof(sbuf), rbuf, |
| sizeof(rbuf), 0); |
| if (ret) |
| deb_info("%s: failed disable demod reset\n", __func__); |
| |
| return 0; |
| } |
| |
| static struct hd29l2_config hdic_hd29l2_config = { |
| .i2c_addr = 0x73, |
| .tuner_i2c_addr = 0x60, |
| .ts_mode = HD29L2_TS_PARALLEL, |
| }; |
| |
| static int hdic_frontend_attach(struct dvb_usb_adapter *adap) |
| { |
| int ret; |
| u8 sbuf[2]; |
| u8 rbuf[3]; |
| |
| deb_info("%s:\n", __func__); |
| |
| /* wake-up device */ |
| sbuf[0] = HDIC_CMD_GET_FIRMWARE_VERSION; |
| ret = dvb_usb_generic_rw(adap->dev, sbuf, sizeof(sbuf), rbuf, |
| sizeof(rbuf), 0); |
| if (ret) |
| deb_info("%s: failed wake-up\n", __func__); |
| |
| /* disable demod reset */ |
| sbuf[0] = HDIC_CMD_DEMOD_RESET; |
| sbuf[1] = 0; |
| ret = dvb_usb_generic_rw(adap->dev, sbuf, sizeof(sbuf), rbuf, |
| sizeof(rbuf), 0); |
| if (ret) |
| deb_info("%s: failed disable demod reset\n", __func__); |
| |
| /* attach demod */ |
| adap->fe_adap[0].fe = dvb_attach(hd29l2_attach, &hdic_hd29l2_config, |
| &adap->dev->i2c_adap); |
| if (adap->fe_adap[0].fe == NULL) { |
| ret = -ENODEV; |
| goto err; |
| } |
| |
| /* setup the reset callback */ |
| adap->fe_adap[0].fe->callback = hdic_frontend_callback; |
| |
| return 0; |
| err: |
| deb_info("%s: failed=%d\n", __func__, ret); |
| return ret; |
| } |
| |
| static struct mxl5007t_config hdic_mxl5007t_config = { |
| .xtal_freq_hz = MxL_XTAL_24_MHZ, |
| .if_freq_hz = MxL_IF_36_15_MHZ, |
| .invert_if = 1, |
| }; |
| |
| static int hdic_tuner_attach(struct dvb_usb_adapter *adap) |
| { |
| int ret; |
| |
| deb_info("%s:\n", __func__); |
| |
| if (dvb_attach(mxl5007t_attach, adap->fe_adap[0].fe, |
| &adap->dev->i2c_adap, 0x60, &hdic_mxl5007t_config) == NULL) { |
| ret = -ENODEV; |
| goto err; |
| } |
| |
| return 0; |
| err: |
| deb_info("%s: failed=%d\n", __func__, ret); |
| return ret; |
| } |
| |
| /* DVB USB Driver stuff */ |
| static struct dvb_usb_device_properties hdic_properties; |
| |
| static int hdic_probe(struct usb_interface *intf, |
| const struct usb_device_id *id) |
| { |
| return dvb_usb_device_init(intf, &hdic_properties, THIS_MODULE, NULL, |
| adapter_nr); |
| } |
| |
| /* |
| * 04b4:1004 HDIC development board firmware |
| * 04b4:8613 CY7C68013 EZ-USB FX2 USB 2.0 Development Kit |
| */ |
| static struct usb_device_id hdic_id[] = { |
| #define HDIC_8613 0 /* CY7C68013 EZ-USB FX2 USB 2.0 Development Kit */ |
| #define HDIC_1004 1 /* HDIC 04b4:1004 */ |
| #define HDIC_LINUX 2 /* HDIC Linux custom firmware */ |
| |
| [HDIC_8613] = {USB_DEVICE(USB_VID_CYPRESS, 0x8613)}, |
| [HDIC_1004] = {USB_DEVICE(USB_VID_CYPRESS, 0x1004)}, |
| [HDIC_LINUX] = {USB_DEVICE(USB_VID_CYPRESS, 0x1e04)}, |
| {} /* terminating entry */ |
| }; |
| |
| MODULE_DEVICE_TABLE(usb, hdic_id); |
| |
| static struct dvb_usb_device_properties hdic_properties = { |
| .caps = DVB_USB_IS_AN_I2C_ADAPTER, |
| |
| .usb_ctrl = CYPRESS_FX2, |
| .firmware = "dvb-usb-hdic.fw", |
| |
| .num_adapters = 1, |
| .adapter = { |
| { |
| .num_frontends = 1, |
| .fe = { |
| { |
| .streaming_ctrl = hdic_streaming_ctrl, |
| .frontend_attach = hdic_frontend_attach, |
| .tuner_attach = hdic_tuner_attach, |
| |
| .stream = { |
| .type = USB_BULK, |
| .count = 5, |
| .endpoint = 0x02, |
| .u = { |
| .bulk = { |
| .buffersize = |
| (4*512), |
| } |
| } |
| }, |
| } |
| }, |
| } |
| }, |
| |
| .power_ctrl = hdic_power_ctrl, |
| |
| .i2c_algo = &hdic_i2c_algo, |
| |
| .generic_bulk_ctrl_endpoint = 1, |
| |
| .num_device_descs = 1, |
| .devices = { |
| { |
| .name = "HDIC reference design", |
| .cold_ids = {&hdic_id[HDIC_8613], |
| &hdic_id[HDIC_1004], NULL}, |
| .warm_ids = {&hdic_id[HDIC_LINUX], NULL}, |
| }, |
| } |
| }; |
| |
| static struct usb_driver hdic_driver = { |
| .name = "dvb_usb_hdic", |
| .probe = hdic_probe, |
| .disconnect = dvb_usb_device_exit, |
| .id_table = hdic_id, |
| }; |
| |
| /* module stuff */ |
| static int __init hdic_module_init(void) |
| { |
| int ret; |
| |
| deb_info("%s:\n", __func__); |
| |
| ret = usb_register(&hdic_driver); |
| if (ret) |
| err("module init failed=%d", ret); |
| |
| return ret; |
| } |
| |
| static void __exit hdic_module_exit(void) |
| { |
| deb_info("%s:\n", __func__); |
| |
| /* deregister this driver from the USB subsystem */ |
| usb_deregister(&hdic_driver); |
| } |
| |
| module_init(hdic_module_init); |
| module_exit(hdic_module_exit); |
| |
| MODULE_AUTHOR("Antti Palosaari <crope@iki.fi>"); |
| MODULE_DESCRIPTION("HDIC DMB-TH reference design USB2.0 driver (custom firmware)"); |
| MODULE_LICENSE("GPL"); |