SERIAL: 8250: Remove SERIAL_8250_AU1X00
Remove the SERIAL_8250_AU1X00 config symbol. Instead, use the MIPS_ALCHEMY
one which is always defined when building an Au1x00-based platform.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Linux-serial <linux-serial@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This one depends on a previous patch (which removes SOC_AU1X00 and changes
MACH_ALCHEMY) to apply cleanly (and then actually work), so I'd love for
this to go in via the mips tree.
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 891e1dd..09ef570 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -302,7 +302,7 @@
},
};
-#if defined (CONFIG_SERIAL_8250_AU1X00)
+#if defined(CONFIG_MIPS_ALCHEMY)
/* Au1x00 UART hardware has a weird register layout */
static const u8 au_io_in_map[] = {
@@ -422,7 +422,6 @@
return readl(p->membase + offset);
}
-#ifdef CONFIG_SERIAL_8250_AU1X00
static unsigned int au_serial_in(struct uart_port *p, int offset)
{
offset = map_8250_in_reg(p, offset) << p->regshift;
@@ -434,7 +433,6 @@
offset = map_8250_out_reg(p, offset) << p->regshift;
__raw_writel(value, p->membase + offset);
}
-#endif
static unsigned int tsi_serial_in(struct uart_port *p, int offset)
{
@@ -503,12 +501,11 @@
p->serial_out = mem32_serial_out;
break;
-#ifdef CONFIG_SERIAL_8250_AU1X00
case UPIO_AU:
p->serial_in = au_serial_in;
p->serial_out = au_serial_out;
break;
-#endif
+
case UPIO_TSI:
p->serial_in = tsi_serial_in;
p->serial_out = tsi_serial_out;
@@ -535,9 +532,7 @@
switch (p->iotype) {
case UPIO_MEM:
case UPIO_MEM32:
-#ifdef CONFIG_SERIAL_8250_AU1X00
case UPIO_AU:
-#endif
case UPIO_DWAPB:
p->serial_out(p, offset, value);
p->serial_in(p, UART_LCR); /* safe, no side-effects */
@@ -573,7 +568,7 @@
serial_outp(up, UART_DLM, value >> 8 & 0xff);
}
-#if defined(CONFIG_SERIAL_8250_AU1X00)
+#if defined(CONFIG_MIPS_ALCHEMY)
/* Au1x00 haven't got a standard divisor latch */
static int serial_dl_read(struct uart_8250_port *up)
{
@@ -2596,11 +2591,9 @@
if (flags & UART_CONFIG_TYPE)
autoconfig(up, probeflags);
-#ifdef CONFIG_SERIAL_8250_AU1X00
/* if access method is AU, it is a 16550 with a quirk */
if (up->port.type == PORT_16550A && up->port.iotype == UPIO_AU)
up->bugs |= UART_BUG_NOMSR;
-#endif
if (up->port.type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ)
autoconfig_irq(up);