| |
| /* include/asm-m68knommu/MC68VZ328.h: 'VZ328 control registers |
| * |
| * Copyright (c) 2000-2001 Lineo Inc. <www.lineo.com> |
| * Copyright (c) 2000-2001 Lineo Canada Corp. <www.lineo.ca> |
| * Copyright (C) 1999 Vladimir Gurevich <vgurevic@cisco.com> |
| * Bare & Hare Software, Inc. |
| * Based on include/asm-m68knommu/MC68332.h |
| * Copyright (C) 1998 Kenneth Albanowski <kjahds@kjahds.com>, |
| * The Silver Hammer Group, Ltd. |
| * |
| * M68VZ328 fixes by Evan Stawnyczy <evan@lineo.com> |
| * vz multiport fixes by Michael Leslie <mleslie@lineo.com> |
| */ |
| |
| #ifndef _MC68VZ328_H_ |
| #define _MC68VZ328_H_ |
| |
| #define BYTE_REF(addr) (*((volatile unsigned char*)addr)) |
| #define WORD_REF(addr) (*((volatile unsigned short*)addr)) |
| #define LONG_REF(addr) (*((volatile unsigned long*)addr)) |
| |
| #define PUT_FIELD(field, val) (((val) << field##_SHIFT) & field##_MASK) |
| #define GET_FIELD(reg, field) (((reg) & field##_MASK) >> field##_SHIFT) |
| |
| /********** |
| * |
| * 0xFFFFF0xx -- System Control |
| * |
| **********/ |
| |
| /* |
| * System Control Register (SCR) |
| */ |
| #define SCR_ADDR 0xfffff000 |
| #define SCR BYTE_REF(SCR_ADDR) |
| |
| #define SCR_WDTH8 0x01 /* 8-Bit Width Select */ |
| #define SCR_DMAP 0x04 /* Double Map */ |
| #define SCR_SO 0x08 /* Supervisor Only */ |
| #define SCR_BETEN 0x10 /* Bus-Error Time-Out Enable */ |
| #define SCR_PRV 0x20 /* Privilege Violation */ |
| #define SCR_WPV 0x40 /* Write Protect Violation */ |
| #define SCR_BETO 0x80 /* Bus-Error TimeOut */ |
| |
| /* |
| * Silicon ID Register (Mask Revision Register (MRR) for '328 Compatibility) |
| */ |
| #define MRR_ADDR 0xfffff004 |
| #define MRR LONG_REF(MRR_ADDR) |
| |
| /********** |
| * |
| * 0xFFFFF1xx -- Chip-Select logic |
| * |
| **********/ |
| |
| /* |
| * Chip Select Group Base Registers |
| */ |
| #define CSGBA_ADDR 0xfffff100 |
| #define CSGBB_ADDR 0xfffff102 |
| |
| #define CSGBC_ADDR 0xfffff104 |
| #define CSGBD_ADDR 0xfffff106 |
| |
| #define CSGBA WORD_REF(CSGBA_ADDR) |
| #define CSGBB WORD_REF(CSGBB_ADDR) |
| #define CSGBC WORD_REF(CSGBC_ADDR) |
| #define CSGBD WORD_REF(CSGBD_ADDR) |
| |
| /* |
| * Chip Select Registers |
| */ |
| #define CSA_ADDR 0xfffff110 |
| #define CSB_ADDR 0xfffff112 |
| #define CSC_ADDR 0xfffff114 |
| #define CSD_ADDR 0xfffff116 |
| |
| #define CSA WORD_REF(CSA_ADDR) |
| #define CSB WORD_REF(CSB_ADDR) |
| #define CSC WORD_REF(CSC_ADDR) |
| #define CSD WORD_REF(CSD_ADDR) |
| |
| #define CSA_EN 0x0001 /* Chip-Select Enable */ |
| #define CSA_SIZ_MASK 0x000e /* Chip-Select Size */ |
| #define CSA_SIZ_SHIFT 1 |
| #define CSA_WS_MASK 0x0070 /* Wait State */ |
| #define CSA_WS_SHIFT 4 |
| #define CSA_BSW 0x0080 /* Data Bus Width */ |
| #define CSA_FLASH 0x0100 /* FLASH Memory Support */ |
| #define CSA_RO 0x8000 /* Read-Only */ |
| |
| #define CSB_EN 0x0001 /* Chip-Select Enable */ |
| #define CSB_SIZ_MASK 0x000e /* Chip-Select Size */ |
| #define CSB_SIZ_SHIFT 1 |
| #define CSB_WS_MASK 0x0070 /* Wait State */ |
| #define CSB_WS_SHIFT 4 |
| #define CSB_BSW 0x0080 /* Data Bus Width */ |
| #define CSB_FLASH 0x0100 /* FLASH Memory Support */ |
| #define CSB_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ |
| #define CSB_UPSIZ_SHIFT 11 |
| #define CSB_ROP 0x2000 /* Readonly if protected */ |
| #define CSB_SOP 0x4000 /* Supervisor only if protected */ |
| #define CSB_RO 0x8000 /* Read-Only */ |
| |
| #define CSC_EN 0x0001 /* Chip-Select Enable */ |
| #define CSC_SIZ_MASK 0x000e /* Chip-Select Size */ |
| #define CSC_SIZ_SHIFT 1 |
| #define CSC_WS_MASK 0x0070 /* Wait State */ |
| #define CSC_WS_SHIFT 4 |
| #define CSC_BSW 0x0080 /* Data Bus Width */ |
| #define CSC_FLASH 0x0100 /* FLASH Memory Support */ |
| #define CSC_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ |
| #define CSC_UPSIZ_SHIFT 11 |
| #define CSC_ROP 0x2000 /* Readonly if protected */ |
| #define CSC_SOP 0x4000 /* Supervisor only if protected */ |
| #define CSC_RO 0x8000 /* Read-Only */ |
| |
| #define CSD_EN 0x0001 /* Chip-Select Enable */ |
| #define CSD_SIZ_MASK 0x000e /* Chip-Select Size */ |
| #define CSD_SIZ_SHIFT 1 |
| #define CSD_WS_MASK 0x0070 /* Wait State */ |
| #define CSD_WS_SHIFT 4 |
| #define CSD_BSW 0x0080 /* Data Bus Width */ |
| #define CSD_FLASH 0x0100 /* FLASH Memory Support */ |
| #define CSD_DRAM 0x0200 /* Dram Selection */ |
| #define CSD_COMB 0x0400 /* Combining */ |
| #define CSD_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ |
| #define CSD_UPSIZ_SHIFT 11 |
| #define CSD_ROP 0x2000 /* Readonly if protected */ |
| #define CSD_SOP 0x4000 /* Supervisor only if protected */ |
| #define CSD_RO 0x8000 /* Read-Only */ |
| |
| /* |
| * Emulation Chip-Select Register |
| */ |
| #define EMUCS_ADDR 0xfffff118 |
| #define EMUCS WORD_REF(EMUCS_ADDR) |
| |
| #define EMUCS_WS_MASK 0x0070 |
| #define EMUCS_WS_SHIFT 4 |
| |
| /********** |
| * |
| * 0xFFFFF2xx -- Phase Locked Loop (PLL) & Power Control |
| * |
| **********/ |
| |
| /* |
| * PLL Control Register |
| */ |
| #define PLLCR_ADDR 0xfffff200 |
| #define PLLCR WORD_REF(PLLCR_ADDR) |
| |
| #define PLLCR_DISPLL 0x0008 /* Disable PLL */ |
| #define PLLCR_CLKEN 0x0010 /* Clock (CLKO pin) enable */ |
| #define PLLCR_PRESC 0x0020 /* VCO prescaler */ |
| #define PLLCR_SYSCLK_SEL_MASK 0x0700 /* System Clock Selection */ |
| #define PLLCR_SYSCLK_SEL_SHIFT 8 |
| #define PLLCR_LCDCLK_SEL_MASK 0x3800 /* LCD Clock Selection */ |
| #define PLLCR_LCDCLK_SEL_SHIFT 11 |
| |
| /* '328-compatible definitions */ |
| #define PLLCR_PIXCLK_SEL_MASK PLLCR_LCDCLK_SEL_MASK |
| #define PLLCR_PIXCLK_SEL_SHIFT PLLCR_LCDCLK_SEL_SHIFT |
| |
| /* |
| * PLL Frequency Select Register |
| */ |
| #define PLLFSR_ADDR 0xfffff202 |
| #define PLLFSR WORD_REF(PLLFSR_ADDR) |
| |
| #define PLLFSR_PC_MASK 0x00ff /* P Count */ |
| #define PLLFSR_PC_SHIFT 0 |
| #define PLLFSR_QC_MASK 0x0f00 /* Q Count */ |
| #define PLLFSR_QC_SHIFT 8 |
| #define PLLFSR_PROT 0x4000 /* Protect P & Q */ |
| #define PLLFSR_CLK32 0x8000 /* Clock 32 (kHz) */ |
| |
| /* |
| * Power Control Register |
| */ |
| #define PCTRL_ADDR 0xfffff207 |
| #define PCTRL BYTE_REF(PCTRL_ADDR) |
| |
| #define PCTRL_WIDTH_MASK 0x1f /* CPU Clock bursts width */ |
| #define PCTRL_WIDTH_SHIFT 0 |
| #define PCTRL_PCEN 0x80 /* Power Control Enable */ |
| |
| /********** |
| * |
| * 0xFFFFF3xx -- Interrupt Controller |
| * |
| **********/ |
| |
| /* |
| * Interrupt Vector Register |
| */ |
| #define IVR_ADDR 0xfffff300 |
| #define IVR BYTE_REF(IVR_ADDR) |
| |
| #define IVR_VECTOR_MASK 0xF8 |
| |
| /* |
| * Interrupt control Register |
| */ |
| #define ICR_ADDR 0xfffff302 |
| #define ICR WORD_REF(ICR_ADDR) |
| |
| #define ICR_POL5 0x0080 /* Polarity Control for IRQ5 */ |
| #define ICR_ET6 0x0100 /* Edge Trigger Select for IRQ6 */ |
| #define ICR_ET3 0x0200 /* Edge Trigger Select for IRQ3 */ |
| #define ICR_ET2 0x0400 /* Edge Trigger Select for IRQ2 */ |
| #define ICR_ET1 0x0800 /* Edge Trigger Select for IRQ1 */ |
| #define ICR_POL6 0x1000 /* Polarity Control for IRQ6 */ |
| #define ICR_POL3 0x2000 /* Polarity Control for IRQ3 */ |
| #define ICR_POL2 0x4000 /* Polarity Control for IRQ2 */ |
| #define ICR_POL1 0x8000 /* Polarity Control for IRQ1 */ |
| |
| /* |
| * Interrupt Mask Register |
| */ |
| #define IMR_ADDR 0xfffff304 |
| #define IMR LONG_REF(IMR_ADDR) |
| |
| /* |
| * Define the names for bit positions first. This is useful for |
| * request_irq |
| */ |
| #define SPI2_IRQ_NUM 0 /* SPI 2 interrupt */ |
| #define TMR_IRQ_NUM 1 /* Timer 1 interrupt */ |
| #define UART1_IRQ_NUM 2 /* UART 1 interrupt */ |
| #define WDT_IRQ_NUM 3 /* Watchdog Timer interrupt */ |
| #define RTC_IRQ_NUM 4 /* RTC interrupt */ |
| #define TMR2_IRQ_NUM 5 /* Timer 2 interrupt */ |
| #define KB_IRQ_NUM 6 /* Keyboard Interrupt */ |
| #define PWM1_IRQ_NUM 7 /* Pulse-Width Modulator 1 int. */ |
| #define INT0_IRQ_NUM 8 /* External INT0 */ |
| #define INT1_IRQ_NUM 9 /* External INT1 */ |
| #define INT2_IRQ_NUM 10 /* External INT2 */ |
| #define INT3_IRQ_NUM 11 /* External INT3 */ |
| #define UART2_IRQ_NUM 12 /* UART 2 interrupt */ |
| #define PWM2_IRQ_NUM 13 /* Pulse-Width Modulator 1 int. */ |
| #define IRQ1_IRQ_NUM 16 /* IRQ1 */ |
| #define IRQ2_IRQ_NUM 17 /* IRQ2 */ |
| #define IRQ3_IRQ_NUM 18 /* IRQ3 */ |
| #define IRQ6_IRQ_NUM 19 /* IRQ6 */ |
| #define IRQ5_IRQ_NUM 20 /* IRQ5 */ |
| #define SPI1_IRQ_NUM 21 /* SPI 1 interrupt */ |
| #define SAM_IRQ_NUM 22 /* Sampling Timer for RTC */ |
| #define EMIQ_IRQ_NUM 23 /* Emulator Interrupt */ |
| |
| #define SPI_IRQ_NUM SPI2_IRQ_NUM |
| |
| /* '328-compatible definitions */ |
| #define SPIM_IRQ_NUM SPI_IRQ_NUM |
| #define TMR1_IRQ_NUM TMR_IRQ_NUM |
| #define UART_IRQ_NUM UART1_IRQ_NUM |
| |
| /* |
| * Here go the bitmasks themselves |
| */ |
| #define IMR_MSPI (1 << SPI_IRQ_NUM) /* Mask SPI interrupt */ |
| #define IMR_MTMR (1 << TMR_IRQ_NUM) /* Mask Timer interrupt */ |
| #define IMR_MUART (1 << UART_IRQ_NUM) /* Mask UART interrupt */ |
| #define IMR_MWDT (1 << WDT_IRQ_NUM) /* Mask Watchdog Timer interrupt */ |
| #define IMR_MRTC (1 << RTC_IRQ_NUM) /* Mask RTC interrupt */ |
| #define IMR_MKB (1 << KB_IRQ_NUM) /* Mask Keyboard Interrupt */ |
| #define IMR_MPWM (1 << PWM_IRQ_NUM) /* Mask Pulse-Width Modulator int. */ |
| #define IMR_MINT0 (1 << INT0_IRQ_NUM) /* Mask External INT0 */ |
| #define IMR_MINT1 (1 << INT1_IRQ_NUM) /* Mask External INT1 */ |
| #define IMR_MINT2 (1 << INT2_IRQ_NUM) /* Mask External INT2 */ |
| #define IMR_MINT3 (1 << INT3_IRQ_NUM) /* Mask External INT3 */ |
| #define IMR_MIRQ1 (1 << IRQ1_IRQ_NUM) /* Mask IRQ1 */ |
| #define IMR_MIRQ2 (1 << IRQ2_IRQ_NUM) /* Mask IRQ2 */ |
| #define IMR_MIRQ3 (1 << IRQ3_IRQ_NUM) /* Mask IRQ3 */ |
| #define IMR_MIRQ6 (1 << IRQ6_IRQ_NUM) /* Mask IRQ6 */ |
| #define IMR_MIRQ5 (1 << IRQ5_IRQ_NUM) /* Mask IRQ5 */ |
| #define IMR_MSAM (1 << SAM_IRQ_NUM) /* Mask Sampling Timer for RTC */ |
| #define IMR_MEMIQ (1 << EMIQ_IRQ_NUM) /* Mask Emulator Interrupt */ |
| |
| /* '328-compatible definitions */ |
| #define IMR_MSPIM IMR_MSPI |
| #define IMR_MTMR1 IMR_MTMR |
| |
| /* |
| * Interrupt Status Register |
| */ |
| #define ISR_ADDR 0xfffff30c |
| #define ISR LONG_REF(ISR_ADDR) |
| |
| #define ISR_SPI (1 << SPI_IRQ_NUM) /* SPI interrupt */ |
| #define ISR_TMR (1 << TMR_IRQ_NUM) /* Timer interrupt */ |
| #define ISR_UART (1 << UART_IRQ_NUM) /* UART interrupt */ |
| #define ISR_WDT (1 << WDT_IRQ_NUM) /* Watchdog Timer interrupt */ |
| #define ISR_RTC (1 << RTC_IRQ_NUM) /* RTC interrupt */ |
| #define ISR_KB (1 << KB_IRQ_NUM) /* Keyboard Interrupt */ |
| #define ISR_PWM (1 << PWM_IRQ_NUM) /* Pulse-Width Modulator interrupt */ |
| #define ISR_INT0 (1 << INT0_IRQ_NUM) /* External INT0 */ |
| #define ISR_INT1 (1 << INT1_IRQ_NUM) /* External INT1 */ |
| #define ISR_INT2 (1 << INT2_IRQ_NUM) /* External INT2 */ |
| #define ISR_INT3 (1 << INT3_IRQ_NUM) /* External INT3 */ |
| #define ISR_IRQ1 (1 << IRQ1_IRQ_NUM) /* IRQ1 */ |
| #define ISR_IRQ2 (1 << IRQ2_IRQ_NUM) /* IRQ2 */ |
| #define ISR_IRQ3 (1 << IRQ3_IRQ_NUM) /* IRQ3 */ |
| #define ISR_IRQ6 (1 << IRQ6_IRQ_NUM) /* IRQ6 */ |
| #define ISR_IRQ5 (1 << IRQ5_IRQ_NUM) /* IRQ5 */ |
| #define ISR_SAM (1 << SAM_IRQ_NUM) /* Sampling Timer for RTC */ |
| #define ISR_EMIQ (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */ |
| |
| /* '328-compatible definitions */ |
| #define ISR_SPIM ISR_SPI |
| #define ISR_TMR1 ISR_TMR |
| |
| /* |
| * Interrupt Pending Register |
| */ |
| #define IPR_ADDR 0xfffff30c |
| #define IPR LONG_REF(IPR_ADDR) |
| |
| #define IPR_SPI (1 << SPI_IRQ_NUM) /* SPI interrupt */ |
| #define IPR_TMR (1 << TMR_IRQ_NUM) /* Timer interrupt */ |
| #define IPR_UART (1 << UART_IRQ_NUM) /* UART interrupt */ |
| #define IPR_WDT (1 << WDT_IRQ_NUM) /* Watchdog Timer interrupt */ |
| #define IPR_RTC (1 << RTC_IRQ_NUM) /* RTC interrupt */ |
| #define IPR_KB (1 << KB_IRQ_NUM) /* Keyboard Interrupt */ |
| #define IPR_PWM (1 << PWM_IRQ_NUM) /* Pulse-Width Modulator interrupt */ |
| #define IPR_INT0 (1 << INT0_IRQ_NUM) /* External INT0 */ |
| #define IPR_INT1 (1 << INT1_IRQ_NUM) /* External INT1 */ |
| #define IPR_INT2 (1 << INT2_IRQ_NUM) /* External INT2 */ |
| #define IPR_INT3 (1 << INT3_IRQ_NUM) /* External INT3 */ |
| #define IPR_IRQ1 (1 << IRQ1_IRQ_NUM) /* IRQ1 */ |
| #define IPR_IRQ2 (1 << IRQ2_IRQ_NUM) /* IRQ2 */ |
| #define IPR_IRQ3 (1 << IRQ3_IRQ_NUM) /* IRQ3 */ |
| #define IPR_IRQ6 (1 << IRQ6_IRQ_NUM) /* IRQ6 */ |
| #define IPR_IRQ5 (1 << IRQ5_IRQ_NUM) /* IRQ5 */ |
| #define IPR_SAM (1 << SAM_IRQ_NUM) /* Sampling Timer for RTC */ |
| #define IPR_EMIQ (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */ |
| |
| /* '328-compatible definitions */ |
| #define IPR_SPIM IPR_SPI |
| #define IPR_TMR1 IPR_TMR |
| |
| /********** |
| * |
| * 0xFFFFF4xx -- Parallel Ports |
| * |
| **********/ |
| |
| /* |
| * Port A |
| */ |
| #define PADIR_ADDR 0xfffff400 /* Port A direction reg */ |
| #define PADATA_ADDR 0xfffff401 /* Port A data register */ |
| #define PAPUEN_ADDR 0xfffff402 /* Port A Pull-Up enable reg */ |
| |
| #define PADIR BYTE_REF(PADIR_ADDR) |
| #define PADATA BYTE_REF(PADATA_ADDR) |
| #define PAPUEN BYTE_REF(PAPUEN_ADDR) |
| |
| #define PA(x) (1 << (x)) |
| |
| /* |
| * Port B |
| */ |
| #define PBDIR_ADDR 0xfffff408 /* Port B direction reg */ |
| #define PBDATA_ADDR 0xfffff409 /* Port B data register */ |
| #define PBPUEN_ADDR 0xfffff40a /* Port B Pull-Up enable reg */ |
| #define PBSEL_ADDR 0xfffff40b /* Port B Select Register */ |
| |
| #define PBDIR BYTE_REF(PBDIR_ADDR) |
| #define PBDATA BYTE_REF(PBDATA_ADDR) |
| #define PBPUEN BYTE_REF(PBPUEN_ADDR) |
| #define PBSEL BYTE_REF(PBSEL_ADDR) |
| |
| #define PB(x) (1 << (x)) |
| |
| #define PB_CSB0 0x01 /* Use CSB0 as PB[0] */ |
| #define PB_CSB1 0x02 /* Use CSB1 as PB[1] */ |
| #define PB_CSC0_RAS0 0x04 /* Use CSC0/RAS0 as PB[2] */ |
| #define PB_CSC1_RAS1 0x08 /* Use CSC1/RAS1 as PB[3] */ |
| #define PB_CSD0_CAS0 0x10 /* Use CSD0/CAS0 as PB[4] */ |
| #define PB_CSD1_CAS1 0x20 /* Use CSD1/CAS1 as PB[5] */ |
| #define PB_TIN_TOUT 0x40 /* Use TIN/TOUT as PB[6] */ |
| #define PB_PWMO 0x80 /* Use PWMO as PB[7] */ |
| |
| /* |
| * Port C |
| */ |
| #define PCDIR_ADDR 0xfffff410 /* Port C direction reg */ |
| #define PCDATA_ADDR 0xfffff411 /* Port C data register */ |
| #define PCPDEN_ADDR 0xfffff412 /* Port C Pull-Down enb. reg */ |
| #define PCSEL_ADDR 0xfffff413 /* Port C Select Register */ |
| |
| #define PCDIR BYTE_REF(PCDIR_ADDR) |
| #define PCDATA BYTE_REF(PCDATA_ADDR) |
| #define PCPDEN BYTE_REF(PCPDEN_ADDR) |
| #define PCSEL BYTE_REF(PCSEL_ADDR) |
| |
| #define PC(x) (1 << (x)) |
| |
| #define PC_LD0 0x01 /* Use LD0 as PC[0] */ |
| #define PC_LD1 0x02 /* Use LD1 as PC[1] */ |
| #define PC_LD2 0x04 /* Use LD2 as PC[2] */ |
| #define PC_LD3 0x08 /* Use LD3 as PC[3] */ |
| #define PC_LFLM 0x10 /* Use LFLM as PC[4] */ |
| #define PC_LLP 0x20 /* Use LLP as PC[5] */ |
| #define PC_LCLK 0x40 /* Use LCLK as PC[6] */ |
| #define PC_LACD 0x80 /* Use LACD as PC[7] */ |
| |
| /* |
| * Port D |
| */ |
| #define PDDIR_ADDR 0xfffff418 /* Port D direction reg */ |
| #define PDDATA_ADDR 0xfffff419 /* Port D data register */ |
| #define PDPUEN_ADDR 0xfffff41a /* Port D Pull-Up enable reg */ |
| #define PDSEL_ADDR 0xfffff41b /* Port D Select Register */ |
| #define PDPOL_ADDR 0xfffff41c /* Port D Polarity Register */ |
| #define PDIRQEN_ADDR 0xfffff41d /* Port D IRQ enable register */ |
| #define PDKBEN_ADDR 0xfffff41e /* Port D Keyboard Enable reg */ |
| #define PDIQEG_ADDR 0xfffff41f /* Port D IRQ Edge Register */ |
| |
| #define PDDIR BYTE_REF(PDDIR_ADDR) |
| #define PDDATA BYTE_REF(PDDATA_ADDR) |
| #define PDPUEN BYTE_REF(PDPUEN_ADDR) |
| #define PDSEL BYTE_REF(PDSEL_ADDR) |
| #define PDPOL BYTE_REF(PDPOL_ADDR) |
| #define PDIRQEN BYTE_REF(PDIRQEN_ADDR) |
| #define PDKBEN BYTE_REF(PDKBEN_ADDR) |
| #define PDIQEG BYTE_REF(PDIQEG_ADDR) |
| |
| #define PD(x) (1 << (x)) |
| |
| #define PD_INT0 0x01 /* Use INT0 as PD[0] */ |
| #define PD_INT1 0x02 /* Use INT1 as PD[1] */ |
| #define PD_INT2 0x04 /* Use INT2 as PD[2] */ |
| #define PD_INT3 0x08 /* Use INT3 as PD[3] */ |
| #define PD_IRQ1 0x10 /* Use IRQ1 as PD[4] */ |
| #define PD_IRQ2 0x20 /* Use IRQ2 as PD[5] */ |
| #define PD_IRQ3 0x40 /* Use IRQ3 as PD[6] */ |
| #define PD_IRQ6 0x80 /* Use IRQ6 as PD[7] */ |
| |
| /* |
| * Port E |
| */ |
| #define PEDIR_ADDR 0xfffff420 /* Port E direction reg */ |
| #define PEDATA_ADDR 0xfffff421 /* Port E data register */ |
| #define PEPUEN_ADDR 0xfffff422 /* Port E Pull-Up enable reg */ |
| #define PESEL_ADDR 0xfffff423 /* Port E Select Register */ |
| |
| #define PEDIR BYTE_REF(PEDIR_ADDR) |
| #define PEDATA BYTE_REF(PEDATA_ADDR) |
| #define PEPUEN BYTE_REF(PEPUEN_ADDR) |
| #define PESEL BYTE_REF(PESEL_ADDR) |
| |
| #define PE(x) (1 << (x)) |
| |
| #define PE_SPMTXD 0x01 /* Use SPMTXD as PE[0] */ |
| #define PE_SPMRXD 0x02 /* Use SPMRXD as PE[1] */ |
| #define PE_SPMCLK 0x04 /* Use SPMCLK as PE[2] */ |
| #define PE_DWE 0x08 /* Use DWE as PE[3] */ |
| #define PE_RXD 0x10 /* Use RXD as PE[4] */ |
| #define PE_TXD 0x20 /* Use TXD as PE[5] */ |
| #define PE_RTS 0x40 /* Use RTS as PE[6] */ |
| #define PE_CTS 0x80 /* Use CTS as PE[7] */ |
| |
| /* |
| * Port F |
| */ |
| #define PFDIR_ADDR 0xfffff428 /* Port F direction reg */ |
| #define PFDATA_ADDR 0xfffff429 /* Port F data register */ |
| #define PFPUEN_ADDR 0xfffff42a /* Port F Pull-Up enable reg */ |
| #define PFSEL_ADDR 0xfffff42b /* Port F Select Register */ |
| |
| #define PFDIR BYTE_REF(PFDIR_ADDR) |
| #define PFDATA BYTE_REF(PFDATA_ADDR) |
| #define PFPUEN BYTE_REF(PFPUEN_ADDR) |
| #define PFSEL BYTE_REF(PFSEL_ADDR) |
| |
| #define PF(x) (1 << (x)) |
| |
| #define PF_LCONTRAST 0x01 /* Use LCONTRAST as PF[0] */ |
| #define PF_IRQ5 0x02 /* Use IRQ5 as PF[1] */ |
| #define PF_CLKO 0x04 /* Use CLKO as PF[2] */ |
| #define PF_A20 0x08 /* Use A20 as PF[3] */ |
| #define PF_A21 0x10 /* Use A21 as PF[4] */ |
| #define PF_A22 0x20 /* Use A22 as PF[5] */ |
| #define PF_A23 0x40 /* Use A23 as PF[6] */ |
| #define PF_CSA1 0x80 /* Use CSA1 as PF[7] */ |
| |
| /* |
| * Port G |
| */ |
| #define PGDIR_ADDR 0xfffff430 /* Port G direction reg */ |
| #define PGDATA_ADDR 0xfffff431 /* Port G data register */ |
| #define PGPUEN_ADDR 0xfffff432 /* Port G Pull-Up enable reg */ |
| #define PGSEL_ADDR 0xfffff433 /* Port G Select Register */ |
| |
| #define PGDIR BYTE_REF(PGDIR_ADDR) |
| #define PGDATA BYTE_REF(PGDATA_ADDR) |
| #define PGPUEN BYTE_REF(PGPUEN_ADDR) |
| #define PGSEL BYTE_REF(PGSEL_ADDR) |
| |
| #define PG(x) (1 << (x)) |
| |
| #define PG_BUSW_DTACK 0x01 /* Use BUSW/DTACK as PG[0] */ |
| #define PG_A0 0x02 /* Use A0 as PG[1] */ |
| #define PG_EMUIRQ 0x04 /* Use EMUIRQ as PG[2] */ |
| #define PG_HIZ_P_D 0x08 /* Use HIZ/P/D as PG[3] */ |
| #define PG_EMUCS 0x10 /* Use EMUCS as PG[4] */ |
| #define PG_EMUBRK 0x20 /* Use EMUBRK as PG[5] */ |
| |
| /* |
| * Port J |
| */ |
| #define PJDIR_ADDR 0xfffff438 /* Port J direction reg */ |
| #define PJDATA_ADDR 0xfffff439 /* Port J data register */ |
| #define PJPUEN_ADDR 0xfffff43A /* Port J Pull-Up enb. reg */ |
| #define PJSEL_ADDR 0xfffff43B /* Port J Select Register */ |
| |
| #define PJDIR BYTE_REF(PJDIR_ADDR) |
| #define PJDATA BYTE_REF(PJDATA_ADDR) |
| #define PJPUEN BYTE_REF(PJPUEN_ADDR) |
| #define PJSEL BYTE_REF(PJSEL_ADDR) |
| |
| #define PJ(x) (1 << (x)) |
| |
| /* |
| * Port K |
| */ |
| #define PKDIR_ADDR 0xfffff440 /* Port K direction reg */ |
| #define PKDATA_ADDR 0xfffff441 /* Port K data register */ |
| #define PKPUEN_ADDR 0xfffff442 /* Port K Pull-Up enb. reg */ |
| #define PKSEL_ADDR 0xfffff443 /* Port K Select Register */ |
| |
| #define PKDIR BYTE_REF(PKDIR_ADDR) |
| #define PKDATA BYTE_REF(PKDATA_ADDR) |
| #define PKPUEN BYTE_REF(PKPUEN_ADDR) |
| #define PKSEL BYTE_REF(PKSEL_ADDR) |
| |
| #define PK(x) (1 << (x)) |
| |
| #define PK_DATAREADY 0x01 /* Use ~DATA_READY as PK[0] */ |
| #define PK_PWM2 0x01 /* Use PWM2 as PK[0] */ |
| #define PK_R_W 0x02 /* Use R/W as PK[1] */ |
| #define PK_LDS 0x04 /* Use /LDS as PK[2] */ |
| #define PK_UDS 0x08 /* Use /UDS as PK[3] */ |
| #define PK_LD4 0x10 /* Use LD4 as PK[4] */ |
| #define PK_LD5 0x20 /* Use LD5 as PK[5] */ |
| #define PK_LD6 0x40 /* Use LD6 as PK[6] */ |
| #define PK_LD7 0x80 /* Use LD7 as PK[7] */ |
| |
| #define PJDIR_ADDR 0xfffff438 /* Port J direction reg */ |
| #define PJDATA_ADDR 0xfffff439 /* Port J data register */ |
| #define PJPUEN_ADDR 0xfffff43A /* Port J Pull-Up enable reg */ |
| #define PJSEL_ADDR 0xfffff43B /* Port J Select Register */ |
| |
| #define PJDIR BYTE_REF(PJDIR_ADDR) |
| #define PJDATA BYTE_REF(PJDATA_ADDR) |
| #define PJPUEN BYTE_REF(PJPUEN_ADDR) |
| #define PJSEL BYTE_REF(PJSEL_ADDR) |
| |
| #define PJ(x) (1 << (x)) |
| |
| #define PJ_MOSI 0x01 /* Use MOSI as PJ[0] */ |
| #define PJ_MISO 0x02 /* Use MISO as PJ[1] */ |
| #define PJ_SPICLK1 0x04 /* Use SPICLK1 as PJ[2] */ |
| #define PJ_SS 0x08 /* Use SS as PJ[3] */ |
| #define PJ_RXD2 0x10 /* Use RXD2 as PJ[4] */ |
| #define PJ_TXD2 0x20 /* Use TXD2 as PJ[5] */ |
| #define PJ_RTS2 0x40 /* Use RTS2 as PJ[5] */ |
| #define PJ_CTS2 0x80 /* Use CTS2 as PJ[5] */ |
| |
| /* |
| * Port M |
| */ |
| #define PMDIR_ADDR 0xfffff448 /* Port M direction reg */ |
| #define PMDATA_ADDR 0xfffff449 /* Port M data register */ |
| #define PMPUEN_ADDR 0xfffff44a /* Port M Pull-Up enable reg */ |
| #define PMSEL_ADDR 0xfffff44b /* Port M Select Register */ |
| |
| #define PMDIR BYTE_REF(PMDIR_ADDR) |
| #define PMDATA BYTE_REF(PMDATA_ADDR) |
| #define PMPUEN BYTE_REF(PMPUEN_ADDR) |
| #define PMSEL BYTE_REF(PMSEL_ADDR) |
| |
| #define PM(x) (1 << (x)) |
| |
| #define PM_SDCLK 0x01 /* Use SDCLK as PM[0] */ |
| #define PM_SDCE 0x02 /* Use SDCE as PM[1] */ |
| #define PM_DQMH 0x04 /* Use DQMH as PM[2] */ |
| #define PM_DQML 0x08 /* Use DQML as PM[3] */ |
| #define PM_SDA10 0x10 /* Use SDA10 as PM[4] */ |
| #define PM_DMOE 0x20 /* Use DMOE as PM[5] */ |
| |
| /********** |
| * |
| * 0xFFFFF5xx -- Pulse-Width Modulator (PWM) |
| * |
| **********/ |
| |
| /* |
| * PWM Control Register |
| */ |
| #define PWMC_ADDR 0xfffff500 |
| #define PWMC WORD_REF(PWMC_ADDR) |
| |
| #define PWMC_CLKSEL_MASK 0x0003 /* Clock Selection */ |
| #define PWMC_CLKSEL_SHIFT 0 |
| #define PWMC_REPEAT_MASK 0x000c /* Sample Repeats */ |
| #define PWMC_REPEAT_SHIFT 2 |
| #define PWMC_EN 0x0010 /* Enable PWM */ |
| #define PMNC_FIFOAV 0x0020 /* FIFO Available */ |
| #define PWMC_IRQEN 0x0040 /* Interrupt Request Enable */ |
| #define PWMC_IRQ 0x0080 /* Interrupt Request (FIFO empty) */ |
| #define PWMC_PRESCALER_MASK 0x7f00 /* Incoming Clock prescaler */ |
| #define PWMC_PRESCALER_SHIFT 8 |
| #define PWMC_CLKSRC 0x8000 /* Clock Source Select */ |
| |
| /* '328-compatible definitions */ |
| #define PWMC_PWMEN PWMC_EN |
| |
| /* |
| * PWM Sample Register |
| */ |
| #define PWMS_ADDR 0xfffff502 |
| #define PWMS WORD_REF(PWMS_ADDR) |
| |
| /* |
| * PWM Period Register |
| */ |
| #define PWMP_ADDR 0xfffff504 |
| #define PWMP BYTE_REF(PWMP_ADDR) |
| |
| /* |
| * PWM Counter Register |
| */ |
| #define PWMCNT_ADDR 0xfffff505 |
| #define PWMCNT BYTE_REF(PWMCNT_ADDR) |
| |
| /********** |
| * |
| * 0xFFFFF6xx -- General-Purpose Timer |
| * |
| **********/ |
| |
| /* |
| * Timer Control register |
| */ |
| #define TCTL_ADDR 0xfffff600 |
| #define TCTL WORD_REF(TCTL_ADDR) |
| |
| #define TCTL_TEN 0x0001 /* Timer Enable */ |
| #define TCTL_CLKSOURCE_MASK 0x000e /* Clock Source: */ |
| #define TCTL_CLKSOURCE_STOP 0x0000 /* Stop count (disabled) */ |
| #define TCTL_CLKSOURCE_SYSCLK 0x0002 /* SYSCLK to prescaler */ |
| #define TCTL_CLKSOURCE_SYSCLK_16 0x0004 /* SYSCLK/16 to prescaler */ |
| #define TCTL_CLKSOURCE_TIN 0x0006 /* TIN to prescaler */ |
| #define TCTL_CLKSOURCE_32KHZ 0x0008 /* 32kHz clock to prescaler */ |
| #define TCTL_IRQEN 0x0010 /* IRQ Enable */ |
| #define TCTL_OM 0x0020 /* Output Mode */ |
| #define TCTL_CAP_MASK 0x00c0 /* Capture Edge: */ |
| #define TCTL_CAP_RE 0x0040 /* Capture on rizing edge */ |
| #define TCTL_CAP_FE 0x0080 /* Capture on falling edge */ |
| #define TCTL_FRR 0x0010 /* Free-Run Mode */ |
| |
| /* '328-compatible definitions */ |
| #define TCTL1_ADDR TCTL_ADDR |
| #define TCTL1 TCTL |
| |
| /* |
| * Timer Prescaler Register |
| */ |
| #define TPRER_ADDR 0xfffff602 |
| #define TPRER WORD_REF(TPRER_ADDR) |
| |
| /* '328-compatible definitions */ |
| #define TPRER1_ADDR TPRER_ADDR |
| #define TPRER1 TPRER |
| |
| /* |
| * Timer Compare Register |
| */ |
| #define TCMP_ADDR 0xfffff604 |
| #define TCMP WORD_REF(TCMP_ADDR) |
| |
| /* '328-compatible definitions */ |
| #define TCMP1_ADDR TCMP_ADDR |
| #define TCMP1 TCMP |
| |
| /* |
| * Timer Capture register |
| */ |
| #define TCR_ADDR 0xfffff606 |
| #define TCR WORD_REF(TCR_ADDR) |
| |
| /* '328-compatible definitions */ |
| #define TCR1_ADDR TCR_ADDR |
| #define TCR1 TCR |
| |
| /* |
| * Timer Counter Register |
| */ |
| #define TCN_ADDR 0xfffff608 |
| #define TCN WORD_REF(TCN_ADDR) |
| |
| /* '328-compatible definitions */ |
| #define TCN1_ADDR TCN_ADDR |
| #define TCN1 TCN |
| |
| /* |
| * Timer Status Register |
| */ |
| #define TSTAT_ADDR 0xfffff60a |
| #define TSTAT WORD_REF(TSTAT_ADDR) |
| |
| #define TSTAT_COMP 0x0001 /* Compare Event occurred */ |
| #define TSTAT_CAPT 0x0001 /* Capture Event occurred */ |
| |
| /* '328-compatible definitions */ |
| #define TSTAT1_ADDR TSTAT_ADDR |
| #define TSTAT1 TSTAT |
| |
| /********** |
| * |
| * 0xFFFFF8xx -- Serial Peripheral Interface Master (SPIM) |
| * |
| **********/ |
| |
| /* |
| * SPIM Data Register |
| */ |
| #define SPIMDATA_ADDR 0xfffff800 |
| #define SPIMDATA WORD_REF(SPIMDATA_ADDR) |
| |
| /* |
| * SPIM Control/Status Register |
| */ |
| #define SPIMCONT_ADDR 0xfffff802 |
| #define SPIMCONT WORD_REF(SPIMCONT_ADDR) |
| |
| #define SPIMCONT_BIT_COUNT_MASK 0x000f /* Transfer Length in Bytes */ |
| #define SPIMCONT_BIT_COUNT_SHIFT 0 |
| #define SPIMCONT_POL 0x0010 /* SPMCLK Signel Polarity */ |
| #define SPIMCONT_PHA 0x0020 /* Clock/Data phase relationship */ |
| #define SPIMCONT_IRQEN 0x0040 /* IRQ Enable */ |
| #define SPIMCONT_IRQ 0x0080 /* Interrupt Request */ |
| #define SPIMCONT_XCH 0x0100 /* Exchange */ |
| #define SPIMCONT_ENABLE 0x0200 /* Enable SPIM */ |
| #define SPIMCONT_DATA_RATE_MASK 0xe000 /* SPIM Data Rate */ |
| #define SPIMCONT_DATA_RATE_SHIFT 13 |
| |
| /* '328-compatible definitions */ |
| #define SPIMCONT_SPIMIRQ SPIMCONT_IRQ |
| #define SPIMCONT_SPIMEN SPIMCONT_ENABLE |
| |
| /********** |
| * |
| * 0xFFFFF9xx -- UART |
| * |
| **********/ |
| |
| /* |
| * UART Status/Control Register |
| */ |
| |
| #define USTCNT_ADDR 0xfffff900 |
| #define USTCNT WORD_REF(USTCNT_ADDR) |
| |
| #define USTCNT_TXAE 0x0001 /* Transmitter Available Interrupt Enable */ |
| #define USTCNT_TXHE 0x0002 /* Transmitter Half Empty Enable */ |
| #define USTCNT_TXEE 0x0004 /* Transmitter Empty Interrupt Enable */ |
| #define USTCNT_RXRE 0x0008 /* Receiver Ready Interrupt Enable */ |
| #define USTCNT_RXHE 0x0010 /* Receiver Half-Full Interrupt Enable */ |
| #define USTCNT_RXFE 0x0020 /* Receiver Full Interrupt Enable */ |
| #define USTCNT_CTSD 0x0040 /* CTS Delta Interrupt Enable */ |
| #define USTCNT_ODEN 0x0080 /* Old Data Interrupt Enable */ |
| #define USTCNT_8_7 0x0100 /* Eight or seven-bit transmission */ |
| #define USTCNT_STOP 0x0200 /* Stop bit transmission */ |
| #define USTCNT_ODD 0x0400 /* Odd Parity */ |
| #define USTCNT_PEN 0x0800 /* Parity Enable */ |
| #define USTCNT_CLKM 0x1000 /* Clock Mode Select */ |
| #define USTCNT_TXEN 0x2000 /* Transmitter Enable */ |
| #define USTCNT_RXEN 0x4000 /* Receiver Enable */ |
| #define USTCNT_UEN 0x8000 /* UART Enable */ |
| |
| /* '328-compatible definitions */ |
| #define USTCNT_TXAVAILEN USTCNT_TXAE |
| #define USTCNT_TXHALFEN USTCNT_TXHE |
| #define USTCNT_TXEMPTYEN USTCNT_TXEE |
| #define USTCNT_RXREADYEN USTCNT_RXRE |
| #define USTCNT_RXHALFEN USTCNT_RXHE |
| #define USTCNT_RXFULLEN USTCNT_RXFE |
| #define USTCNT_CTSDELTAEN USTCNT_CTSD |
| #define USTCNT_ODD_EVEN USTCNT_ODD |
| #define USTCNT_PARITYEN USTCNT_PEN |
| #define USTCNT_CLKMODE USTCNT_CLKM |
| #define USTCNT_UARTEN USTCNT_UEN |
| |
| /* |
| * UART Baud Control Register |
| */ |
| #define UBAUD_ADDR 0xfffff902 |
| #define UBAUD WORD_REF(UBAUD_ADDR) |
| |
| #define UBAUD_PRESCALER_MASK 0x003f /* Actual divisor is 65 - PRESCALER */ |
| #define UBAUD_PRESCALER_SHIFT 0 |
| #define UBAUD_DIVIDE_MASK 0x0700 /* Baud Rate freq. divisor */ |
| #define UBAUD_DIVIDE_SHIFT 8 |
| #define UBAUD_BAUD_SRC 0x0800 /* Baud Rate Source */ |
| #define UBAUD_UCLKDIR 0x2000 /* UCLK Direction */ |
| |
| /* |
| * UART Receiver Register |
| */ |
| #define URX_ADDR 0xfffff904 |
| #define URX WORD_REF(URX_ADDR) |
| |
| #define URX_RXDATA_ADDR 0xfffff905 |
| #define URX_RXDATA BYTE_REF(URX_RXDATA_ADDR) |
| |
| #define URX_RXDATA_MASK 0x00ff /* Received data */ |
| #define URX_RXDATA_SHIFT 0 |
| #define URX_PARITY_ERROR 0x0100 /* Parity Error */ |
| #define URX_BREAK 0x0200 /* Break Detected */ |
| #define URX_FRAME_ERROR 0x0400 /* Framing Error */ |
| #define URX_OVRUN 0x0800 /* Serial Overrun */ |
| #define URX_OLD_DATA 0x1000 /* Old data in FIFO */ |
| #define URX_DATA_READY 0x2000 /* Data Ready (FIFO not empty) */ |
| #define URX_FIFO_HALF 0x4000 /* FIFO is Half-Full */ |
| #define URX_FIFO_FULL 0x8000 /* FIFO is Full */ |
| |
| /* |
| * UART Transmitter Register |
| */ |
| #define UTX_ADDR 0xfffff906 |
| #define UTX WORD_REF(UTX_ADDR) |
| |
| #define UTX_TXDATA_ADDR 0xfffff907 |
| #define UTX_TXDATA BYTE_REF(UTX_TXDATA_ADDR) |
| |
| #define UTX_TXDATA_MASK 0x00ff /* Data to be transmitted */ |
| #define UTX_TXDATA_SHIFT 0 |
| #define UTX_CTS_DELTA 0x0100 /* CTS changed */ |
| #define UTX_CTS_STAT 0x0200 /* CTS State */ |
| #define UTX_BUSY 0x0400 /* FIFO is busy, sending a character */ |
| #define UTX_NOCTS 0x0800 /* Ignore CTS */ |
| #define UTX_SEND_BREAK 0x1000 /* Send a BREAK */ |
| #define UTX_TX_AVAIL 0x2000 /* Transmit FIFO has a slot available */ |
| #define UTX_FIFO_HALF 0x4000 /* Transmit FIFO is half empty */ |
| #define UTX_FIFO_EMPTY 0x8000 /* Transmit FIFO is empty */ |
| |
| /* '328-compatible definitions */ |
| #define UTX_CTS_STATUS UTX_CTS_STAT |
| #define UTX_IGNORE_CTS UTX_NOCTS |
| |
| /* |
| * UART Miscellaneous Register |
| */ |
| #define UMISC_ADDR 0xfffff908 |
| #define UMISC WORD_REF(UMISC_ADDR) |
| |
| #define UMISC_TX_POL 0x0004 /* Transmit Polarity */ |
| #define UMISC_RX_POL 0x0008 /* Receive Polarity */ |
| #define UMISC_IRDA_LOOP 0x0010 /* IrDA Loopback Enable */ |
| #define UMISC_IRDA_EN 0x0020 /* Infra-Red Enable */ |
| #define UMISC_RTS 0x0040 /* Set RTS status */ |
| #define UMISC_RTSCONT 0x0080 /* Choose RTS control */ |
| #define UMISC_IR_TEST 0x0400 /* IRDA Test Enable */ |
| #define UMISC_BAUD_RESET 0x0800 /* Reset Baud Rate Generation Counters */ |
| #define UMISC_LOOP 0x1000 /* Serial Loopback Enable */ |
| #define UMISC_FORCE_PERR 0x2000 /* Force Parity Error */ |
| #define UMISC_CLKSRC 0x4000 /* Clock Source */ |
| #define UMISC_BAUD_TEST 0x8000 /* Enable Baud Test Mode */ |
| |
| /* |
| * UART Non-integer Prescaler Register |
| */ |
| #define NIPR_ADDR 0xfffff90a |
| #define NIPR WORD_REF(NIPR_ADDR) |
| |
| #define NIPR_STEP_VALUE_MASK 0x00ff /* NI prescaler step value */ |
| #define NIPR_STEP_VALUE_SHIFT 0 |
| #define NIPR_SELECT_MASK 0x0700 /* Tap Selection */ |
| #define NIPR_SELECT_SHIFT 8 |
| #define NIPR_PRE_SEL 0x8000 /* Non-integer prescaler select */ |
| |
| |
| /* generalization of uart control registers to support multiple ports: */ |
| typedef struct { |
| volatile unsigned short int ustcnt; |
| volatile unsigned short int ubaud; |
| union { |
| volatile unsigned short int w; |
| struct { |
| volatile unsigned char status; |
| volatile unsigned char rxdata; |
| } b; |
| } urx; |
| union { |
| volatile unsigned short int w; |
| struct { |
| volatile unsigned char status; |
| volatile unsigned char txdata; |
| } b; |
| } utx; |
| volatile unsigned short int umisc; |
| volatile unsigned short int nipr; |
| volatile unsigned short int hmark; |
| volatile unsigned short int unused; |
| } __attribute__((packed)) m68328_uart; |
| |
| |
| |
| |
| /********** |
| * |
| * 0xFFFFFAxx -- LCD Controller |
| * |
| **********/ |
| |
| /* |
| * LCD Screen Starting Address Register |
| */ |
| #define LSSA_ADDR 0xfffffa00 |
| #define LSSA LONG_REF(LSSA_ADDR) |
| |
| #define LSSA_SSA_MASK 0x1ffffffe /* Bits 0 and 29-31 are reserved */ |
| |
| /* |
| * LCD Virtual Page Width Register |
| */ |
| #define LVPW_ADDR 0xfffffa05 |
| #define LVPW BYTE_REF(LVPW_ADDR) |
| |
| /* |
| * LCD Screen Width Register (not compatible with '328 !!!) |
| */ |
| #define LXMAX_ADDR 0xfffffa08 |
| #define LXMAX WORD_REF(LXMAX_ADDR) |
| |
| #define LXMAX_XM_MASK 0x02f0 /* Bits 0-3 and 10-15 are reserved */ |
| |
| /* |
| * LCD Screen Height Register |
| */ |
| #define LYMAX_ADDR 0xfffffa0a |
| #define LYMAX WORD_REF(LYMAX_ADDR) |
| |
| #define LYMAX_YM_MASK 0x01ff /* Bits 9-15 are reserved */ |
| |
| /* |
| * LCD Cursor X Position Register |
| */ |
| #define LCXP_ADDR 0xfffffa18 |
| #define LCXP WORD_REF(LCXP_ADDR) |
| |
| #define LCXP_CC_MASK 0xc000 /* Cursor Control */ |
| #define LCXP_CC_TRAMSPARENT 0x0000 |
| #define LCXP_CC_BLACK 0x4000 |
| #define LCXP_CC_REVERSED 0x8000 |
| #define LCXP_CC_WHITE 0xc000 |
| #define LCXP_CXP_MASK 0x02ff /* Cursor X position */ |
| |
| /* |
| * LCD Cursor Y Position Register |
| */ |
| #define LCYP_ADDR 0xfffffa1a |
| #define LCYP WORD_REF(LCYP_ADDR) |
| |
| #define LCYP_CYP_MASK 0x01ff /* Cursor Y Position */ |
| |
| /* |
| * LCD Cursor Width and Heigth Register |
| */ |
| #define LCWCH_ADDR 0xfffffa1c |
| #define LCWCH WORD_REF(LCWCH_ADDR) |
| |
| #define LCWCH_CH_MASK 0x001f /* Cursor Height */ |
| #define LCWCH_CH_SHIFT 0 |
| #define LCWCH_CW_MASK 0x1f00 /* Cursor Width */ |
| #define LCWCH_CW_SHIFT 8 |
| |
| /* |
| * LCD Blink Control Register |
| */ |
| #define LBLKC_ADDR 0xfffffa1f |
| #define LBLKC BYTE_REF(LBLKC_ADDR) |
| |
| #define LBLKC_BD_MASK 0x7f /* Blink Divisor */ |
| #define LBLKC_BD_SHIFT 0 |
| #define LBLKC_BKEN 0x80 /* Blink Enabled */ |
| |
| /* |
| * LCD Panel Interface Configuration Register |
| */ |
| #define LPICF_ADDR 0xfffffa20 |
| #define LPICF BYTE_REF(LPICF_ADDR) |
| |
| #define LPICF_GS_MASK 0x03 /* Gray-Scale Mode */ |
| #define LPICF_GS_BW 0x00 |
| #define LPICF_GS_GRAY_4 0x01 |
| #define LPICF_GS_GRAY_16 0x02 |
| #define LPICF_PBSIZ_MASK 0x0c /* Panel Bus Width */ |
| #define LPICF_PBSIZ_1 0x00 |
| #define LPICF_PBSIZ_2 0x04 |
| #define LPICF_PBSIZ_4 0x08 |
| |
| /* |
| * LCD Polarity Configuration Register |
| */ |
| #define LPOLCF_ADDR 0xfffffa21 |
| #define LPOLCF BYTE_REF(LPOLCF_ADDR) |
| |
| #define LPOLCF_PIXPOL 0x01 /* Pixel Polarity */ |
| #define LPOLCF_LPPOL 0x02 /* Line Pulse Polarity */ |
| #define LPOLCF_FLMPOL 0x04 /* Frame Marker Polarity */ |
| #define LPOLCF_LCKPOL 0x08 /* LCD Shift Lock Polarity */ |
| |
| /* |
| * LACD (LCD Alternate Crystal Direction) Rate Control Register |
| */ |
| #define LACDRC_ADDR 0xfffffa23 |
| #define LACDRC BYTE_REF(LACDRC_ADDR) |
| |
| #define LACDRC_ACDSLT 0x80 /* Signal Source Select */ |
| #define LACDRC_ACD_MASK 0x0f /* Alternate Crystal Direction Control */ |
| #define LACDRC_ACD_SHIFT 0 |
| |
| /* |
| * LCD Pixel Clock Divider Register |
| */ |
| #define LPXCD_ADDR 0xfffffa25 |
| #define LPXCD BYTE_REF(LPXCD_ADDR) |
| |
| #define LPXCD_PCD_MASK 0x3f /* Pixel Clock Divider */ |
| #define LPXCD_PCD_SHIFT 0 |
| |
| /* |
| * LCD Clocking Control Register |
| */ |
| #define LCKCON_ADDR 0xfffffa27 |
| #define LCKCON BYTE_REF(LCKCON_ADDR) |
| |
| #define LCKCON_DWS_MASK 0x0f /* Display Wait-State */ |
| #define LCKCON_DWS_SHIFT 0 |
| #define LCKCON_DWIDTH 0x40 /* Display Memory Width */ |
| #define LCKCON_LCDON 0x80 /* Enable LCD Controller */ |
| |
| /* '328-compatible definitions */ |
| #define LCKCON_DW_MASK LCKCON_DWS_MASK |
| #define LCKCON_DW_SHIFT LCKCON_DWS_SHIFT |
| |
| /* |
| * LCD Refresh Rate Adjustment Register |
| */ |
| #define LRRA_ADDR 0xfffffa29 |
| #define LRRA BYTE_REF(LRRA_ADDR) |
| |
| /* |
| * LCD Panning Offset Register |
| */ |
| #define LPOSR_ADDR 0xfffffa2d |
| #define LPOSR BYTE_REF(LPOSR_ADDR) |
| |
| #define LPOSR_POS_MASK 0x0f /* Pixel Offset Code */ |
| #define LPOSR_POS_SHIFT 0 |
| |
| /* |
| * LCD Frame Rate Control Modulation Register |
| */ |
| #define LFRCM_ADDR 0xfffffa31 |
| #define LFRCM BYTE_REF(LFRCM_ADDR) |
| |
| #define LFRCM_YMOD_MASK 0x0f /* Vertical Modulation */ |
| #define LFRCM_YMOD_SHIFT 0 |
| #define LFRCM_XMOD_MASK 0xf0 /* Horizontal Modulation */ |
| #define LFRCM_XMOD_SHIFT 4 |
| |
| /* |
| * LCD Gray Palette Mapping Register |
| */ |
| #define LGPMR_ADDR 0xfffffa33 |
| #define LGPMR BYTE_REF(LGPMR_ADDR) |
| |
| #define LGPMR_G1_MASK 0x0f |
| #define LGPMR_G1_SHIFT 0 |
| #define LGPMR_G2_MASK 0xf0 |
| #define LGPMR_G2_SHIFT 4 |
| |
| /* |
| * PWM Contrast Control Register |
| */ |
| #define PWMR_ADDR 0xfffffa36 |
| #define PWMR WORD_REF(PWMR_ADDR) |
| |
| #define PWMR_PW_MASK 0x00ff /* Pulse Width */ |
| #define PWMR_PW_SHIFT 0 |
| #define PWMR_CCPEN 0x0100 /* Contrast Control Enable */ |
| #define PWMR_SRC_MASK 0x0600 /* Input Clock Source */ |
| #define PWMR_SRC_LINE 0x0000 /* Line Pulse */ |
| #define PWMR_SRC_PIXEL 0x0200 /* Pixel Clock */ |
| #define PWMR_SRC_LCD 0x4000 /* LCD clock */ |
| |
| /********** |
| * |
| * 0xFFFFFBxx -- Real-Time Clock (RTC) |
| * |
| **********/ |
| |
| /* |
| * RTC Hours Minutes and Seconds Register |
| */ |
| #define RTCTIME_ADDR 0xfffffb00 |
| #define RTCTIME LONG_REF(RTCTIME_ADDR) |
| |
| #define RTCTIME_SECONDS_MASK 0x0000003f /* Seconds */ |
| #define RTCTIME_SECONDS_SHIFT 0 |
| #define RTCTIME_MINUTES_MASK 0x003f0000 /* Minutes */ |
| #define RTCTIME_MINUTES_SHIFT 16 |
| #define RTCTIME_HOURS_MASK 0x1f000000 /* Hours */ |
| #define RTCTIME_HOURS_SHIFT 24 |
| |
| /* |
| * RTC Alarm Register |
| */ |
| #define RTCALRM_ADDR 0xfffffb04 |
| #define RTCALRM LONG_REF(RTCALRM_ADDR) |
| |
| #define RTCALRM_SECONDS_MASK 0x0000003f /* Seconds */ |
| #define RTCALRM_SECONDS_SHIFT 0 |
| #define RTCALRM_MINUTES_MASK 0x003f0000 /* Minutes */ |
| #define RTCALRM_MINUTES_SHIFT 16 |
| #define RTCALRM_HOURS_MASK 0x1f000000 /* Hours */ |
| #define RTCALRM_HOURS_SHIFT 24 |
| |
| /* |
| * Watchdog Timer Register |
| */ |
| #define WATCHDOG_ADDR 0xfffffb0a |
| #define WATCHDOG WORD_REF(WATCHDOG_ADDR) |
| |
| #define WATCHDOG_EN 0x0001 /* Watchdog Enabled */ |
| #define WATCHDOG_ISEL 0x0002 /* Select the watchdog interrupt */ |
| #define WATCHDOG_INTF 0x0080 /* Watchdog interrupt occurred */ |
| #define WATCHDOG_CNT_MASK 0x0300 /* Watchdog Counter */ |
| #define WATCHDOG_CNT_SHIFT 8 |
| |
| /* |
| * RTC Control Register |
| */ |
| #define RTCCTL_ADDR 0xfffffb0c |
| #define RTCCTL WORD_REF(RTCCTL_ADDR) |
| |
| #define RTCCTL_XTL 0x0020 /* Crystal Selection */ |
| #define RTCCTL_EN 0x0080 /* RTC Enable */ |
| |
| /* '328-compatible definitions */ |
| #define RTCCTL_384 RTCCTL_XTL |
| #define RTCCTL_ENABLE RTCCTL_EN |
| |
| /* |
| * RTC Interrupt Status Register |
| */ |
| #define RTCISR_ADDR 0xfffffb0e |
| #define RTCISR WORD_REF(RTCISR_ADDR) |
| |
| #define RTCISR_SW 0x0001 /* Stopwatch timed out */ |
| #define RTCISR_MIN 0x0002 /* 1-minute interrupt has occurred */ |
| #define RTCISR_ALM 0x0004 /* Alarm interrupt has occurred */ |
| #define RTCISR_DAY 0x0008 /* 24-hour rollover interrupt has occurred */ |
| #define RTCISR_1HZ 0x0010 /* 1Hz interrupt has occurred */ |
| #define RTCISR_HR 0x0020 /* 1-hour interrupt has occurred */ |
| #define RTCISR_SAM0 0x0100 /* 4Hz / 4.6875Hz interrupt has occurred */ |
| #define RTCISR_SAM1 0x0200 /* 8Hz / 9.3750Hz interrupt has occurred */ |
| #define RTCISR_SAM2 0x0400 /* 16Hz / 18.7500Hz interrupt has occurred */ |
| #define RTCISR_SAM3 0x0800 /* 32Hz / 37.5000Hz interrupt has occurred */ |
| #define RTCISR_SAM4 0x1000 /* 64Hz / 75.0000Hz interrupt has occurred */ |
| #define RTCISR_SAM5 0x2000 /* 128Hz / 150.0000Hz interrupt has occurred */ |
| #define RTCISR_SAM6 0x4000 /* 256Hz / 300.0000Hz interrupt has occurred */ |
| #define RTCISR_SAM7 0x8000 /* 512Hz / 600.0000Hz interrupt has occurred */ |
| |
| /* |
| * RTC Interrupt Enable Register |
| */ |
| #define RTCIENR_ADDR 0xfffffb10 |
| #define RTCIENR WORD_REF(RTCIENR_ADDR) |
| |
| #define RTCIENR_SW 0x0001 /* Stopwatch interrupt enable */ |
| #define RTCIENR_MIN 0x0002 /* 1-minute interrupt enable */ |
| #define RTCIENR_ALM 0x0004 /* Alarm interrupt enable */ |
| #define RTCIENR_DAY 0x0008 /* 24-hour rollover interrupt enable */ |
| #define RTCIENR_1HZ 0x0010 /* 1Hz interrupt enable */ |
| #define RTCIENR_HR 0x0020 /* 1-hour interrupt enable */ |
| #define RTCIENR_SAM0 0x0100 /* 4Hz / 4.6875Hz interrupt enable */ |
| #define RTCIENR_SAM1 0x0200 /* 8Hz / 9.3750Hz interrupt enable */ |
| #define RTCIENR_SAM2 0x0400 /* 16Hz / 18.7500Hz interrupt enable */ |
| #define RTCIENR_SAM3 0x0800 /* 32Hz / 37.5000Hz interrupt enable */ |
| #define RTCIENR_SAM4 0x1000 /* 64Hz / 75.0000Hz interrupt enable */ |
| #define RTCIENR_SAM5 0x2000 /* 128Hz / 150.0000Hz interrupt enable */ |
| #define RTCIENR_SAM6 0x4000 /* 256Hz / 300.0000Hz interrupt enable */ |
| #define RTCIENR_SAM7 0x8000 /* 512Hz / 600.0000Hz interrupt enable */ |
| |
| /* |
| * Stopwatch Minutes Register |
| */ |
| #define STPWCH_ADDR 0xfffffb12 |
| #define STPWCH WORD_REF(STPWCH_ADDR) |
| |
| #define STPWCH_CNT_MASK 0x003f /* Stopwatch countdown value */ |
| #define SPTWCH_CNT_SHIFT 0 |
| |
| /* |
| * RTC Day Count Register |
| */ |
| #define DAYR_ADDR 0xfffffb1a |
| #define DAYR WORD_REF(DAYR_ADDR) |
| |
| #define DAYR_DAYS_MASK 0x1ff /* Day Setting */ |
| #define DAYR_DAYS_SHIFT 0 |
| |
| /* |
| * RTC Day Alarm Register |
| */ |
| #define DAYALARM_ADDR 0xfffffb1c |
| #define DAYALARM WORD_REF(DAYALARM_ADDR) |
| |
| #define DAYALARM_DAYSAL_MASK 0x01ff /* Day Setting of the Alarm */ |
| #define DAYALARM_DAYSAL_SHIFT 0 |
| |
| /********** |
| * |
| * 0xFFFFFCxx -- DRAM Controller |
| * |
| **********/ |
| |
| /* |
| * DRAM Memory Configuration Register |
| */ |
| #define DRAMMC_ADDR 0xfffffc00 |
| #define DRAMMC WORD_REF(DRAMMC_ADDR) |
| |
| #define DRAMMC_ROW12_MASK 0xc000 /* Row address bit for MD12 */ |
| #define DRAMMC_ROW12_PA10 0x0000 |
| #define DRAMMC_ROW12_PA21 0x4000 |
| #define DRAMMC_ROW12_PA23 0x8000 |
| #define DRAMMC_ROW0_MASK 0x3000 /* Row address bit for MD0 */ |
| #define DRAMMC_ROW0_PA11 0x0000 |
| #define DRAMMC_ROW0_PA22 0x1000 |
| #define DRAMMC_ROW0_PA23 0x2000 |
| #define DRAMMC_ROW11 0x0800 /* Row address bit for MD11 PA20/PA22 */ |
| #define DRAMMC_ROW10 0x0400 /* Row address bit for MD10 PA19/PA21 */ |
| #define DRAMMC_ROW9 0x0200 /* Row address bit for MD9 PA9/PA19 */ |
| #define DRAMMC_ROW8 0x0100 /* Row address bit for MD8 PA10/PA20 */ |
| #define DRAMMC_COL10 0x0080 /* Col address bit for MD10 PA11/PA0 */ |
| #define DRAMMC_COL9 0x0040 /* Col address bit for MD9 PA10/PA0 */ |
| #define DRAMMC_COL8 0x0020 /* Col address bit for MD8 PA9/PA0 */ |
| #define DRAMMC_REF_MASK 0x001f /* Refresh Cycle */ |
| #define DRAMMC_REF_SHIFT 0 |
| |
| /* |
| * DRAM Control Register |
| */ |
| #define DRAMC_ADDR 0xfffffc02 |
| #define DRAMC WORD_REF(DRAMC_ADDR) |
| |
| #define DRAMC_DWE 0x0001 /* DRAM Write Enable */ |
| #define DRAMC_RST 0x0002 /* Reset Burst Refresh Enable */ |
| #define DRAMC_LPR 0x0004 /* Low-Power Refresh Enable */ |
| #define DRAMC_SLW 0x0008 /* Slow RAM */ |
| #define DRAMC_LSP 0x0010 /* Light Sleep */ |
| #define DRAMC_MSW 0x0020 /* Slow Multiplexing */ |
| #define DRAMC_WS_MASK 0x00c0 /* Wait-states */ |
| #define DRAMC_WS_SHIFT 6 |
| #define DRAMC_PGSZ_MASK 0x0300 /* Page Size for fast page mode */ |
| #define DRAMC_PGSZ_SHIFT 8 |
| #define DRAMC_PGSZ_256K 0x0000 |
| #define DRAMC_PGSZ_512K 0x0100 |
| #define DRAMC_PGSZ_1024K 0x0200 |
| #define DRAMC_PGSZ_2048K 0x0300 |
| #define DRAMC_EDO 0x0400 /* EDO DRAM */ |
| #define DRAMC_CLK 0x0800 /* Refresh Timer Clock source select */ |
| #define DRAMC_BC_MASK 0x3000 /* Page Access Clock Cycle (FP mode) */ |
| #define DRAMC_BC_SHIFT 12 |
| #define DRAMC_RM 0x4000 /* Refresh Mode */ |
| #define DRAMC_EN 0x8000 /* DRAM Controller enable */ |
| |
| |
| /********** |
| * |
| * 0xFFFFFDxx -- In-Circuit Emulation (ICE) |
| * |
| **********/ |
| |
| /* |
| * ICE Module Address Compare Register |
| */ |
| #define ICEMACR_ADDR 0xfffffd00 |
| #define ICEMACR LONG_REF(ICEMACR_ADDR) |
| |
| /* |
| * ICE Module Address Mask Register |
| */ |
| #define ICEMAMR_ADDR 0xfffffd04 |
| #define ICEMAMR LONG_REF(ICEMAMR_ADDR) |
| |
| /* |
| * ICE Module Control Compare Register |
| */ |
| #define ICEMCCR_ADDR 0xfffffd08 |
| #define ICEMCCR WORD_REF(ICEMCCR_ADDR) |
| |
| #define ICEMCCR_PD 0x0001 /* Program/Data Cycle Selection */ |
| #define ICEMCCR_RW 0x0002 /* Read/Write Cycle Selection */ |
| |
| /* |
| * ICE Module Control Mask Register |
| */ |
| #define ICEMCMR_ADDR 0xfffffd0a |
| #define ICEMCMR WORD_REF(ICEMCMR_ADDR) |
| |
| #define ICEMCMR_PDM 0x0001 /* Program/Data Cycle Mask */ |
| #define ICEMCMR_RWM 0x0002 /* Read/Write Cycle Mask */ |
| |
| /* |
| * ICE Module Control Register |
| */ |
| #define ICEMCR_ADDR 0xfffffd0c |
| #define ICEMCR WORD_REF(ICEMCR_ADDR) |
| |
| #define ICEMCR_CEN 0x0001 /* Compare Enable */ |
| #define ICEMCR_PBEN 0x0002 /* Program Break Enable */ |
| #define ICEMCR_SB 0x0004 /* Single Breakpoint */ |
| #define ICEMCR_HMDIS 0x0008 /* HardMap disable */ |
| #define ICEMCR_BBIEN 0x0010 /* Bus Break Interrupt Enable */ |
| |
| /* |
| * ICE Module Status Register |
| */ |
| #define ICEMSR_ADDR 0xfffffd0e |
| #define ICEMSR WORD_REF(ICEMSR_ADDR) |
| |
| #define ICEMSR_EMUEN 0x0001 /* Emulation Enable */ |
| #define ICEMSR_BRKIRQ 0x0002 /* A-Line Vector Fetch Detected */ |
| #define ICEMSR_BBIRQ 0x0004 /* Bus Break Interrupt Detected */ |
| #define ICEMSR_EMIRQ 0x0008 /* EMUIRQ Falling Edge Detected */ |
| |
| #endif /* _MC68VZ328_H_ */ |