| # |
| # EDAC Kconfig |
| # Copyright (c) 2008 Doug Thompson www.softwarebitmaker.com |
| # Licensed and distributed under the GPL |
| |
| config EDAC_ATOMIC_SCRUB |
| bool |
| |
| config EDAC_SUPPORT |
| bool |
| |
| menuconfig EDAC |
| bool "EDAC (Error Detection And Correction) reporting" |
| depends on HAS_IOMEM && EDAC_SUPPORT |
| help |
| EDAC is designed to report errors in the core system. |
| These are low-level errors that are reported in the CPU or |
| supporting chipset or other subsystems: |
| memory errors, cache errors, PCI errors, thermal throttling, etc.. |
| If unsure, select 'Y'. |
| |
| If this code is reporting problems on your system, please |
| see the EDAC project web pages for more information at: |
| |
| <http://bluesmoke.sourceforge.net/> |
| |
| and: |
| |
| <http://buttersideup.com/edacwiki> |
| |
| There is also a mailing list for the EDAC project, which can |
| be found via the sourceforge page. |
| |
| if EDAC |
| |
| config EDAC_LEGACY_SYSFS |
| bool "EDAC legacy sysfs" |
| default y |
| help |
| Enable the compatibility sysfs nodes. |
| Use 'Y' if your edac utilities aren't ported to work with the newer |
| structures. |
| |
| config EDAC_DEBUG |
| bool "Debugging" |
| help |
| This turns on debugging information for the entire EDAC subsystem. |
| You do so by inserting edac_module with "edac_debug_level=x." Valid |
| levels are 0-4 (from low to high) and by default it is set to 2. |
| Usually you should select 'N' here. |
| |
| config EDAC_DECODE_MCE |
| tristate "Decode MCEs in human-readable form (only on AMD for now)" |
| depends on CPU_SUP_AMD && X86_MCE_AMD |
| default y |
| ---help--- |
| Enable this option if you want to decode Machine Check Exceptions |
| occurring on your machine in human-readable form. |
| |
| You should definitely say Y here in case you want to decode MCEs |
| which occur really early upon boot, before the module infrastructure |
| has been initialized. |
| |
| config EDAC_MM_EDAC |
| tristate "Main Memory EDAC (Error Detection And Correction) reporting" |
| select RAS |
| help |
| Some systems are able to detect and correct errors in main |
| memory. EDAC can report statistics on memory error |
| detection and correction (EDAC - or commonly referred to ECC |
| errors). EDAC will also try to decode where these errors |
| occurred so that a particular failing memory module can be |
| replaced. If unsure, select 'Y'. |
| |
| config EDAC_GHES |
| bool "Output ACPI APEI/GHES BIOS detected errors via EDAC" |
| depends on ACPI_APEI_GHES && (EDAC_MM_EDAC=y) |
| default y |
| help |
| Not all machines support hardware-driven error report. Some of those |
| provide a BIOS-driven error report mechanism via ACPI, using the |
| APEI/GHES driver. By enabling this option, the error reports provided |
| by GHES are sent to userspace via the EDAC API. |
| |
| When this option is enabled, it will disable the hardware-driven |
| mechanisms, if a GHES BIOS is detected, entering into the |
| "Firmware First" mode. |
| |
| It should be noticed that keeping both GHES and a hardware-driven |
| error mechanism won't work well, as BIOS will race with OS, while |
| reading the error registers. So, if you want to not use "Firmware |
| first" GHES error mechanism, you should disable GHES either at |
| compilation time or by passing "ghes.disable=1" Kernel parameter |
| at boot time. |
| |
| In doubt, say 'Y'. |
| |
| config EDAC_AMD64 |
| tristate "AMD64 (Opteron, Athlon64)" |
| depends on EDAC_MM_EDAC && AMD_NB && EDAC_DECODE_MCE |
| help |
| Support for error detection and correction of DRAM ECC errors on |
| the AMD64 families (>= K8) of memory controllers. |
| |
| config EDAC_AMD64_ERROR_INJECTION |
| bool "Sysfs HW Error injection facilities" |
| depends on EDAC_AMD64 |
| help |
| Recent Opterons (Family 10h and later) provide for Memory Error |
| Injection into the ECC detection circuits. The amd64_edac module |
| allows the operator/user to inject Uncorrectable and Correctable |
| errors into DRAM. |
| |
| When enabled, in each of the respective memory controller directories |
| (/sys/devices/system/edac/mc/mcX), there are 3 input files: |
| |
| - inject_section (0..3, 16-byte section of 64-byte cacheline), |
| - inject_word (0..8, 16-bit word of 16-byte section), |
| - inject_ecc_vector (hex ecc vector: select bits of inject word) |
| |
| In addition, there are two control files, inject_read and inject_write, |
| which trigger the DRAM ECC Read and Write respectively. |
| |
| config EDAC_AMD76X |
| tristate "AMD 76x (760, 762, 768)" |
| depends on EDAC_MM_EDAC && PCI && X86_32 |
| help |
| Support for error detection and correction on the AMD 76x |
| series of chipsets used with the Athlon processor. |
| |
| config EDAC_E7XXX |
| tristate "Intel e7xxx (e7205, e7500, e7501, e7505)" |
| depends on EDAC_MM_EDAC && PCI && X86_32 |
| help |
| Support for error detection and correction on the Intel |
| E7205, E7500, E7501 and E7505 server chipsets. |
| |
| config EDAC_E752X |
| tristate "Intel e752x (e7520, e7525, e7320) and 3100" |
| depends on EDAC_MM_EDAC && PCI && X86 |
| help |
| Support for error detection and correction on the Intel |
| E7520, E7525, E7320 server chipsets. |
| |
| config EDAC_I82443BXGX |
| tristate "Intel 82443BX/GX (440BX/GX)" |
| depends on EDAC_MM_EDAC && PCI && X86_32 |
| depends on BROKEN |
| help |
| Support for error detection and correction on the Intel |
| 82443BX/GX memory controllers (440BX/GX chipsets). |
| |
| config EDAC_I82875P |
| tristate "Intel 82875p (D82875P, E7210)" |
| depends on EDAC_MM_EDAC && PCI && X86_32 |
| help |
| Support for error detection and correction on the Intel |
| DP82785P and E7210 server chipsets. |
| |
| config EDAC_I82975X |
| tristate "Intel 82975x (D82975x)" |
| depends on EDAC_MM_EDAC && PCI && X86 |
| help |
| Support for error detection and correction on the Intel |
| DP82975x server chipsets. |
| |
| config EDAC_I3000 |
| tristate "Intel 3000/3010" |
| depends on EDAC_MM_EDAC && PCI && X86 |
| help |
| Support for error detection and correction on the Intel |
| 3000 and 3010 server chipsets. |
| |
| config EDAC_I3200 |
| tristate "Intel 3200" |
| depends on EDAC_MM_EDAC && PCI && X86 |
| help |
| Support for error detection and correction on the Intel |
| 3200 and 3210 server chipsets. |
| |
| config EDAC_IE31200 |
| tristate "Intel e312xx" |
| depends on EDAC_MM_EDAC && PCI && X86 |
| help |
| Support for error detection and correction on the Intel |
| E3-1200 based DRAM controllers. |
| |
| config EDAC_X38 |
| tristate "Intel X38" |
| depends on EDAC_MM_EDAC && PCI && X86 |
| help |
| Support for error detection and correction on the Intel |
| X38 server chipsets. |
| |
| config EDAC_I5400 |
| tristate "Intel 5400 (Seaburg) chipsets" |
| depends on EDAC_MM_EDAC && PCI && X86 |
| help |
| Support for error detection and correction the Intel |
| i5400 MCH chipset (Seaburg). |
| |
| config EDAC_I7CORE |
| tristate "Intel i7 Core (Nehalem) processors" |
| depends on EDAC_MM_EDAC && PCI && X86 && X86_MCE_INTEL |
| help |
| Support for error detection and correction the Intel |
| i7 Core (Nehalem) Integrated Memory Controller that exists on |
| newer processors like i7 Core, i7 Core Extreme, Xeon 35xx |
| and Xeon 55xx processors. |
| |
| config EDAC_I82860 |
| tristate "Intel 82860" |
| depends on EDAC_MM_EDAC && PCI && X86_32 |
| help |
| Support for error detection and correction on the Intel |
| 82860 chipset. |
| |
| config EDAC_R82600 |
| tristate "Radisys 82600 embedded chipset" |
| depends on EDAC_MM_EDAC && PCI && X86_32 |
| help |
| Support for error detection and correction on the Radisys |
| 82600 embedded chipset. |
| |
| config EDAC_I5000 |
| tristate "Intel Greencreek/Blackford chipset" |
| depends on EDAC_MM_EDAC && X86 && PCI |
| help |
| Support for error detection and correction the Intel |
| Greekcreek/Blackford chipsets. |
| |
| config EDAC_I5100 |
| tristate "Intel San Clemente MCH" |
| depends on EDAC_MM_EDAC && X86 && PCI |
| help |
| Support for error detection and correction the Intel |
| San Clemente MCH. |
| |
| config EDAC_I7300 |
| tristate "Intel Clarksboro MCH" |
| depends on EDAC_MM_EDAC && X86 && PCI |
| help |
| Support for error detection and correction the Intel |
| Clarksboro MCH (Intel 7300 chipset). |
| |
| config EDAC_SBRIDGE |
| tristate "Intel Sandy-Bridge/Ivy-Bridge/Haswell Integrated MC" |
| depends on EDAC_MM_EDAC && PCI && X86_64 && X86_MCE_INTEL |
| depends on PCI_MMCONFIG |
| help |
| Support for error detection and correction the Intel |
| Sandy Bridge, Ivy Bridge and Haswell Integrated Memory Controllers. |
| |
| config EDAC_SKX |
| tristate "Intel Skylake server Integrated MC" |
| depends on EDAC_MM_EDAC && PCI && X86_64 && X86_MCE_INTEL |
| depends on PCI_MMCONFIG |
| help |
| Support for error detection and correction the Intel |
| Skylake server Integrated Memory Controllers. |
| |
| config EDAC_MPC85XX |
| tristate "Freescale MPC83xx / MPC85xx" |
| depends on EDAC_MM_EDAC && FSL_SOC |
| help |
| Support for error detection and correction on the Freescale |
| MPC8349, MPC8560, MPC8540, MPC8548, T4240 |
| |
| config EDAC_LAYERSCAPE |
| tristate "Freescale Layerscape DDR" |
| depends on EDAC_MM_EDAC && ARCH_LAYERSCAPE |
| help |
| Support for error detection and correction on Freescale memory |
| controllers on Layerscape SoCs. |
| |
| config EDAC_MV64X60 |
| tristate "Marvell MV64x60" |
| depends on EDAC_MM_EDAC && MV64X60 |
| help |
| Support for error detection and correction on the Marvell |
| MV64360 and MV64460 chipsets. |
| |
| config EDAC_PASEMI |
| tristate "PA Semi PWRficient" |
| depends on EDAC_MM_EDAC && PCI |
| depends on PPC_PASEMI |
| help |
| Support for error detection and correction on PA Semi |
| PWRficient. |
| |
| config EDAC_CELL |
| tristate "Cell Broadband Engine memory controller" |
| depends on EDAC_MM_EDAC && PPC_CELL_COMMON |
| help |
| Support for error detection and correction on the |
| Cell Broadband Engine internal memory controller |
| on platform without a hypervisor |
| |
| config EDAC_PPC4XX |
| tristate "PPC4xx IBM DDR2 Memory Controller" |
| depends on EDAC_MM_EDAC && 4xx |
| help |
| This enables support for EDAC on the ECC memory used |
| with the IBM DDR2 memory controller found in various |
| PowerPC 4xx embedded processors such as the 405EX[r], |
| 440SP, 440SPe, 460EX, 460GT and 460SX. |
| |
| config EDAC_AMD8131 |
| tristate "AMD8131 HyperTransport PCI-X Tunnel" |
| depends on EDAC_MM_EDAC && PCI && PPC_MAPLE |
| help |
| Support for error detection and correction on the |
| AMD8131 HyperTransport PCI-X Tunnel chip. |
| Note, add more Kconfig dependency if it's adopted |
| on some machine other than Maple. |
| |
| config EDAC_AMD8111 |
| tristate "AMD8111 HyperTransport I/O Hub" |
| depends on EDAC_MM_EDAC && PCI && PPC_MAPLE |
| help |
| Support for error detection and correction on the |
| AMD8111 HyperTransport I/O Hub chip. |
| Note, add more Kconfig dependency if it's adopted |
| on some machine other than Maple. |
| |
| config EDAC_CPC925 |
| tristate "IBM CPC925 Memory Controller (PPC970FX)" |
| depends on EDAC_MM_EDAC && PPC64 |
| help |
| Support for error detection and correction on the |
| IBM CPC925 Bridge and Memory Controller, which is |
| a companion chip to the PowerPC 970 family of |
| processors. |
| |
| config EDAC_TILE |
| tristate "Tilera Memory Controller" |
| depends on EDAC_MM_EDAC && TILE |
| default y |
| help |
| Support for error detection and correction on the |
| Tilera memory controller. |
| |
| config EDAC_HIGHBANK_MC |
| tristate "Highbank Memory Controller" |
| depends on EDAC_MM_EDAC && ARCH_HIGHBANK |
| help |
| Support for error detection and correction on the |
| Calxeda Highbank memory controller. |
| |
| config EDAC_HIGHBANK_L2 |
| tristate "Highbank L2 Cache" |
| depends on EDAC_MM_EDAC && ARCH_HIGHBANK |
| help |
| Support for error detection and correction on the |
| Calxeda Highbank memory controller. |
| |
| config EDAC_OCTEON_PC |
| tristate "Cavium Octeon Primary Caches" |
| depends on EDAC_MM_EDAC && CPU_CAVIUM_OCTEON |
| help |
| Support for error detection and correction on the primary caches of |
| the cnMIPS cores of Cavium Octeon family SOCs. |
| |
| config EDAC_OCTEON_L2C |
| tristate "Cavium Octeon Secondary Caches (L2C)" |
| depends on EDAC_MM_EDAC && CAVIUM_OCTEON_SOC |
| help |
| Support for error detection and correction on the |
| Cavium Octeon family of SOCs. |
| |
| config EDAC_OCTEON_LMC |
| tristate "Cavium Octeon DRAM Memory Controller (LMC)" |
| depends on EDAC_MM_EDAC && CAVIUM_OCTEON_SOC |
| help |
| Support for error detection and correction on the |
| Cavium Octeon family of SOCs. |
| |
| config EDAC_OCTEON_PCI |
| tristate "Cavium Octeon PCI Controller" |
| depends on EDAC_MM_EDAC && PCI && CAVIUM_OCTEON_SOC |
| help |
| Support for error detection and correction on the |
| Cavium Octeon family of SOCs. |
| |
| config EDAC_ALTERA |
| bool "Altera SOCFPGA ECC" |
| depends on EDAC_MM_EDAC=y && ARCH_SOCFPGA |
| help |
| Support for error detection and correction on the |
| Altera SOCs. This must be selected for SDRAM ECC. |
| Note that the preloader must initialize the SDRAM |
| before loading the kernel. |
| |
| config EDAC_ALTERA_L2C |
| bool "Altera L2 Cache ECC" |
| depends on EDAC_ALTERA=y && CACHE_L2X0 |
| help |
| Support for error detection and correction on the |
| Altera L2 cache Memory for Altera SoCs. This option |
| requires L2 cache. |
| |
| config EDAC_ALTERA_OCRAM |
| bool "Altera On-Chip RAM ECC" |
| depends on EDAC_ALTERA=y && SRAM && GENERIC_ALLOCATOR |
| help |
| Support for error detection and correction on the |
| Altera On-Chip RAM Memory for Altera SoCs. |
| |
| config EDAC_ALTERA_ETHERNET |
| bool "Altera Ethernet FIFO ECC" |
| depends on EDAC_ALTERA=y |
| help |
| Support for error detection and correction on the |
| Altera Ethernet FIFO Memory for Altera SoCs. |
| |
| config EDAC_ALTERA_NAND |
| bool "Altera NAND FIFO ECC" |
| depends on EDAC_ALTERA=y && MTD_NAND_DENALI |
| help |
| Support for error detection and correction on the |
| Altera NAND FIFO Memory for Altera SoCs. |
| |
| config EDAC_ALTERA_DMA |
| bool "Altera DMA FIFO ECC" |
| depends on EDAC_ALTERA=y && PL330_DMA=y |
| help |
| Support for error detection and correction on the |
| Altera DMA FIFO Memory for Altera SoCs. |
| |
| config EDAC_ALTERA_USB |
| bool "Altera USB FIFO ECC" |
| depends on EDAC_ALTERA=y && USB_DWC2 |
| help |
| Support for error detection and correction on the |
| Altera USB FIFO Memory for Altera SoCs. |
| |
| config EDAC_ALTERA_QSPI |
| bool "Altera QSPI FIFO ECC" |
| depends on EDAC_ALTERA=y && SPI_CADENCE_QUADSPI |
| help |
| Support for error detection and correction on the |
| Altera QSPI FIFO Memory for Altera SoCs. |
| |
| config EDAC_ALTERA_SDMMC |
| bool "Altera SDMMC FIFO ECC" |
| depends on EDAC_ALTERA=y && MMC_DW |
| help |
| Support for error detection and correction on the |
| Altera SDMMC FIFO Memory for Altera SoCs. |
| |
| config EDAC_SYNOPSYS |
| tristate "Synopsys DDR Memory Controller" |
| depends on EDAC_MM_EDAC && ARCH_ZYNQ |
| help |
| Support for error detection and correction on the Synopsys DDR |
| memory controller. |
| |
| config EDAC_KRYO3XX_ARM64 |
| depends on EDAC_MM_EDAC && ARM64 |
| tristate "ARM KRYO3XX Gold and Silver L1/L2/L3/SCU Caches" |
| help |
| Support for error detection and correction on the |
| Kryo3xx Gold and Silver CPUs. Reports errors caught by Kryo3xx |
| ECC mechanism. |
| For debugging issues having to do with stability and overall system |
| health, you should probably say 'Y' here. |
| |
| config EDAC_KRYO3XX_ARM64_POLL |
| depends on EDAC_KRYO3XX_ARM64 |
| bool "Poll on kryo3xx ECC registers - kryo3xx" |
| help |
| This option chooses whether or not you want to poll on the Kryo3xx |
| ECC registers. When this is enabled, the polling rate can be set as |
| a module parameter. By default, it will call the polling function |
| every second. |
| This option should only be used if the associated interrupt lines |
| are not enabled. |
| |
| config EDAC_KRYO3XX_ARM64_PANIC_ON_CE |
| depends on EDAC_KRYO3XX_ARM64 |
| bool "Panic on correctable errors - kryo3xx" |
| help |
| Forcibly cause a kernel panic if an correctable error (CE) is |
| detected, even though the error is (by definition) correctable and |
| would otherwise result in no adverse system effects. This can reduce |
| debugging times on hardware which may be operating at voltages or |
| frequencies outside normal specification. |
| For production builds, you should definitely say 'N' here. |
| |
| config EDAC_KRYO3XX_ARM64_PANIC_ON_UE |
| depends on EDAC_KRYO3XX_ARM64 |
| bool "Panic on uncorrectable errors - kryo3xx" |
| help |
| Forcibly cause a kernel panic if an uncorrectable error (UE) is |
| detected. This can reduce debugging times on hardware which may be |
| operating at voltages or frequencies outside normal specification. |
| For production builds, you should probably say 'N' here. |
| |
| config EDAC_XGENE |
| tristate "APM X-Gene SoC" |
| depends on EDAC_MM_EDAC && (ARM64 || COMPILE_TEST) |
| help |
| Support for error detection and correction on the |
| APM X-Gene family of SOCs. |
| |
| config EDAC_QCOM_LLCC |
| depends on EDAC_MM_EDAC && QCOM_LLCC |
| tristate "QCOM LLCC Caches" |
| help |
| Support for error detection and correction on the |
| QCOM LLCC cache. Report errors caught by LLCC ECC |
| mechanism. |
| |
| For debugging issues having to do with stability and overall system |
| health, you should probably say 'Y' here. |
| |
| config EDAC_LLCC_POLL |
| depends on EDAC_QCOM_LLCC |
| bool "Poll on LLCC ECC registers - LLCC" |
| help |
| This option chooses whether or not you want to poll on the LLCC |
| ECC registers. When this is enabled, the polling rate can be set as |
| a module parameter. By default, it will call the polling function |
| every second. |
| This option should only be used if the associated interrupt lines |
| are not enabled. |
| |
| config EDAC_QCOM_LLCC_PANIC_ON_CE |
| depends on EDAC_QCOM_LLCC |
| bool "panic on correctable errors - qcom llcc" |
| help |
| Forcibly cause kernel panic if a correctable error (CE) is |
| detected, even though the error is (by definition) correctable and |
| would otherwise result in no adverse system effects. This can reduce |
| debugging times on hardware which my be operating at voltages or |
| frequencies outside normal specifications. |
| |
| For production builds, you should definitely say 'N' here. |
| |
| config EDAC_QCOM_LLCC_PANIC_ON_UE |
| depends on EDAC_QCOM_LLCC |
| bool "Panic on uncorrectable errors - qcom llcc" |
| help |
| Forcibly cause a kernel panic if an uncorrectable error (UE) is |
| detected. This can reduce debugging times on hardware which may be |
| operating at voltages or frequencies outside normal specification. |
| |
| For production builds, you should probably say 'N' here. |
| |
| endif # EDAC |