| Generic device tree bindings for I2C busses |
| =========================================== |
| |
| This document describes generic bindings which can be used to describe I2C |
| busses in a device tree. |
| |
| Required properties |
| ------------------- |
| |
| - #address-cells - should be <1>. Read more about addresses below. |
| - #size-cells - should be <0>. |
| - compatible - name of I2C bus controller following generic names |
| recommended practice. |
| |
| For other required properties e.g. to describe register sets, |
| clocks, etc. check the binding documentation of the specific driver. |
| |
| The cells properties above define that an address of children of an I2C bus |
| are described by a single value. This is usually a 7 bit address. However, |
| flags can be attached to the address. I2C_TEN_BIT_ADDRESS is used to mark a 10 |
| bit address. It is needed to avoid the ambiguity between e.g. a 7 bit address |
| of 0x50 and a 10 bit address of 0x050 which, in theory, can be on the same bus. |
| Another flag is I2C_OWN_SLAVE_ADDRESS to mark addresses on which we listen to |
| be devices ourselves. |
| |
| Optional properties |
| ------------------- |
| |
| These properties may not be supported by all drivers. However, if a driver |
| wants to support one of the below features, it should adapt the bindings below. |
| |
| - clock-frequency |
| frequency of bus clock in Hz. |
| |
| - i2c-bus |
| For I2C adapters that have child nodes that are a mixture of both I2C |
| devices and non-I2C devices, the 'i2c-bus' subnode can be used for |
| populating I2C devices. If the 'i2c-bus' subnode is present, only |
| subnodes of this will be considered as I2C slaves. The properties, |
| '#address-cells' and '#size-cells' must be defined under this subnode |
| if present. |
| |
| - i2c-scl-falling-time-ns |
| Number of nanoseconds the SCL signal takes to fall; t(f) in the I2C |
| specification. |
| |
| - i2c-scl-internal-delay-ns |
| Number of nanoseconds the IP core additionally needs to setup SCL. |
| |
| - i2c-scl-rising-time-ns |
| Number of nanoseconds the SCL signal takes to rise; t(r) in the I2C |
| specification. |
| |
| - i2c-sda-falling-time-ns |
| Number of nanoseconds the SDA signal takes to fall; t(f) in the I2C |
| specification. |
| |
| - interrupts |
| interrupts used by the device. |
| |
| - interrupt-names |
| "irq" and "wakeup" names are recognized by I2C core, other names are |
| left to individual drivers. |
| |
| - multi-master |
| states that there is another master active on this bus. The OS can use |
| this information to adapt power management to keep the arbitration awake |
| all the time, for example. |
| |
| - wakeup-source |
| device can be used as a wakeup source. |
| |
| - reg |
| I2C slave addresses |
| |
| - reg-names |
| Names of map programmable addresses. |
| It can contain any map needing another address than default one. |
| |
| Binding may contain optional "interrupts" property, describing interrupts |
| used by the device. I2C core will assign "irq" interrupt (or the very first |
| interrupt if not using interrupt names) as primary interrupt for the slave. |
| |
| Also, if device is marked as a wakeup source, I2C core will set up "wakeup" |
| interrupt for the device. If "wakeup" interrupt name is not present in the |
| binding, then primary interrupt will be used as wakeup interrupt. |