staging/wilc1000: avoid static definitions in header
The wilc_wfi_cfgoperations.h header defines the ieee80211_txrx_stypes
and cipher_suites variables that are only used in wilc_wfi_cfgoperations.c
and should not be shared in a header file.
This moves over all that data into the .c file, and also moves all
the macro definitions from the file that are also not needed here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c b/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c
index 49b82b4..46c3f578 100644
--- a/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c
+++ b/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c
@@ -17,6 +17,90 @@
#include "host_interface.h"
#include <linux/errno.h>
+/* The following macros describe the bitfield map used by the firmware to determine its 11i mode */
+#define NO_ENCRYPT 0
+#define ENCRYPT_ENABLED BIT(0)
+#define WEP BIT(1)
+#define WEP_EXTENDED BIT(2)
+#define WPA BIT(3)
+#define WPA2 BIT(4)
+#define AES BIT(5)
+#define TKIP BIT(6)
+
+/*Public action frame index IDs*/
+#define FRAME_TYPE_ID 0
+#define ACTION_CAT_ID 24
+#define ACTION_SUBTYPE_ID 25
+#define P2P_PUB_ACTION_SUBTYPE 30
+
+/*Public action frame Attribute IDs*/
+#define ACTION_FRAME 0xd0
+#define GO_INTENT_ATTR_ID 0x04
+#define CHANLIST_ATTR_ID 0x0b
+#define OPERCHAN_ATTR_ID 0x11
+#define PUB_ACTION_ATTR_ID 0x04
+#define P2PELEM_ATTR_ID 0xdd
+
+/*Public action subtype values*/
+#define GO_NEG_REQ 0x00
+#define GO_NEG_RSP 0x01
+#define GO_NEG_CONF 0x02
+#define P2P_INV_REQ 0x03
+#define P2P_INV_RSP 0x04
+#define PUBLIC_ACT_VENDORSPEC 0x09
+#define GAS_INTIAL_REQ 0x0a
+#define GAS_INTIAL_RSP 0x0b
+
+#define INVALID_CHANNEL 0
+
+#define nl80211_SCAN_RESULT_EXPIRE (3 * HZ)
+#define SCAN_RESULT_EXPIRE (40 * HZ)
+
+static const u32 cipher_suites[] = {
+ WLAN_CIPHER_SUITE_WEP40,
+ WLAN_CIPHER_SUITE_WEP104,
+ WLAN_CIPHER_SUITE_TKIP,
+ WLAN_CIPHER_SUITE_CCMP,
+ WLAN_CIPHER_SUITE_AES_CMAC,
+};
+
+static const struct ieee80211_txrx_stypes
+ wilc_wfi_cfg80211_mgmt_types[NUM_NL80211_IFTYPES] = {
+ [NL80211_IFTYPE_STATION] = {
+ .tx = 0xffff,
+ .rx = BIT(IEEE80211_STYPE_ACTION >> 4) |
+ BIT(IEEE80211_STYPE_PROBE_REQ >> 4)
+ },
+ [NL80211_IFTYPE_AP] = {
+ .tx = 0xffff,
+ .rx = BIT(IEEE80211_STYPE_ASSOC_REQ >> 4) |
+ BIT(IEEE80211_STYPE_REASSOC_REQ >> 4) |
+ BIT(IEEE80211_STYPE_PROBE_REQ >> 4) |
+ BIT(IEEE80211_STYPE_DISASSOC >> 4) |
+ BIT(IEEE80211_STYPE_AUTH >> 4) |
+ BIT(IEEE80211_STYPE_DEAUTH >> 4) |
+ BIT(IEEE80211_STYPE_ACTION >> 4)
+ },
+ [NL80211_IFTYPE_P2P_CLIENT] = {
+ .tx = 0xffff,
+ .rx = BIT(IEEE80211_STYPE_ACTION >> 4) |
+ BIT(IEEE80211_STYPE_PROBE_REQ >> 4) |
+ BIT(IEEE80211_STYPE_ASSOC_REQ >> 4) |
+ BIT(IEEE80211_STYPE_REASSOC_REQ >> 4) |
+ BIT(IEEE80211_STYPE_DISASSOC >> 4) |
+ BIT(IEEE80211_STYPE_AUTH >> 4) |
+ BIT(IEEE80211_STYPE_DEAUTH >> 4)
+ }
+};
+
+/* Time to stay on the channel */
+#define WILC_WFI_DWELL_PASSIVE 100
+#define WILC_WFI_DWELL_ACTIVE 40
+
+#define TCP_ACK_FILTER_LINK_SPEED_THRESH 54
+#define DEFAULT_LINK_SPEED 72
+
+
#define IS_MANAGMEMENT 0x100
#define IS_MANAGMEMENT_CALLBACK 0x080
#define IS_MGMT_STATUS_SUCCES 0x040