tulip: Convert printks to netdev_<level>
Use the current more descriptive logging styles.
Add pr_fmt and remove PFX where appropriate.
Use netif_<level>, netdev_<level>
Indent a few blocks in xircom_cb where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/tulip/tulip_core.c b/drivers/net/tulip/tulip_core.c
index 5c01e26..f46898a 100644
--- a/drivers/net/tulip/tulip_core.c
+++ b/drivers/net/tulip/tulip_core.c
@@ -12,6 +12,7 @@
Please submit bugs to http://bugzilla.kernel.org/ .
*/
+#define pr_fmt(fmt) "tulip: " fmt
#define DRV_NAME "tulip"
#ifdef CONFIG_TULIP_NAPI
@@ -119,8 +120,6 @@
module_param_array(options, int, NULL, 0);
module_param_array(full_duplex, int, NULL, 0);
-#define PFX DRV_NAME ": "
-
#ifdef TULIP_DEBUG
int tulip_debug = TULIP_DEBUG;
#else
@@ -1340,13 +1339,13 @@
*/
if (pdev->subsystem_vendor == PCI_VENDOR_ID_LMC) {
- pr_err(PFX "skipping LMC card\n");
+ pr_err("skipping LMC card\n");
return -ENODEV;
} else if (pdev->subsystem_vendor == PCI_VENDOR_ID_SBE &&
(pdev->subsystem_device == PCI_SUBDEVICE_ID_SBE_T3E3 ||
pdev->subsystem_device == PCI_SUBDEVICE_ID_SBE_2T3E3_P0 ||
pdev->subsystem_device == PCI_SUBDEVICE_ID_SBE_2T3E3_P1)) {
- pr_err(PFX "skipping SBE T3E3 port\n");
+ pr_err("skipping SBE T3E3 port\n");
return -ENODEV;
}
@@ -1362,13 +1361,13 @@
if (pdev->vendor == 0x1282 && pdev->device == 0x9100 &&
pdev->revision < 0x30) {
- pr_info(PFX "skipping early DM9100 with Crc bug (use dmfe)\n");
+ pr_info("skipping early DM9100 with Crc bug (use dmfe)\n");
return -ENODEV;
}
dp = pci_device_to_OF_node(pdev);
if (!(dp && of_get_property(dp, "local-mac-address", NULL))) {
- pr_info(PFX "skipping DM910x expansion card (use dmfe)\n");
+ pr_info("skipping DM910x expansion card (use dmfe)\n");
return -ENODEV;
}
}
@@ -1415,16 +1414,14 @@
i = pci_enable_device(pdev);
if (i) {
- pr_err(PFX "Cannot enable tulip board #%d, aborting\n",
- board_idx);
+ pr_err("Cannot enable tulip board #%d, aborting\n", board_idx);
return i;
}
/* The chip will fail to enter a low-power state later unless
* first explicitly commanded into D0 */
if (pci_set_power_state(pdev, PCI_D0)) {
- printk (KERN_NOTICE PFX
- "Failed to set power state to D0\n");
+ pr_notice("Failed to set power state to D0\n");
}
irq = pdev->irq;
@@ -1432,13 +1429,13 @@
/* alloc_etherdev ensures aligned and zeroed private structures */
dev = alloc_etherdev (sizeof (*tp));
if (!dev) {
- pr_err(PFX "ether device alloc failed, aborting\n");
+ pr_err("ether device alloc failed, aborting\n");
return -ENOMEM;
}
SET_NETDEV_DEV(dev, &pdev->dev);
if (pci_resource_len (pdev, 0) < tulip_tbl[chip_idx].io_size) {
- pr_err(PFX "%s: I/O region (0x%llx@0x%llx) too small, aborting\n",
+ pr_err("%s: I/O region (0x%llx@0x%llx) too small, aborting\n",
pci_name(pdev),
(unsigned long long)pci_resource_len (pdev, 0),
(unsigned long long)pci_resource_start (pdev, 0));
@@ -1905,12 +1902,12 @@
return 0;
if ((retval = pci_enable_device(pdev))) {
- pr_err(PFX "pci_enable_device failed in resume\n");
+ pr_err("pci_enable_device failed in resume\n");
return retval;
}
if ((retval = request_irq(dev->irq, tulip_interrupt, IRQF_SHARED, dev->name, dev))) {
- pr_err(PFX "request_irq failed in resume\n");
+ pr_err("request_irq failed in resume\n");
return retval;
}