atmel_usba_udc: Add support for AT91CAP9 UDPHS
This patch is part of the series adding support for the USB High
Speed Device Port on the AT91CAP9 system on chip. The AT91CAP9
uses the same UDPHS IP as the AVR32 and the AT91SAM9RL.
The only differences between the AVR32 and the AT91 version of the
device are in the enable/disable and suspend/wakeup sequences: the
AT91 version needs to toggle the USB bias and pulldown explicitly.
Signed-off-by: Stelian Pop <stelian@popies.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
diff --git a/drivers/usb/gadget/atmel_usba_udc.c b/drivers/usb/gadget/atmel_usba_udc.c
index ddb7301..c9a3c2a 100644
--- a/drivers/usb/gadget/atmel_usba_udc.c
+++ b/drivers/usb/gadget/atmel_usba_udc.c
@@ -326,6 +326,28 @@
return 1;
}
+#if defined(CONFIG_AVR32)
+
+static void toggle_bias(int is_on)
+{
+}
+
+#elif defined(CONFIG_ARCH_AT91)
+
+#include <asm/arch/at91_pmc.h>
+
+static void toggle_bias(int is_on)
+{
+ unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR);
+
+ if (is_on)
+ at91_sys_write(AT91_CKGR_UCKR, uckr | AT91_PMC_BIASEN);
+ else
+ at91_sys_write(AT91_CKGR_UCKR, uckr & ~(AT91_PMC_BIASEN));
+}
+
+#endif /* CONFIG_ARCH_AT91 */
+
static void next_fifo_transaction(struct usba_ep *ep, struct usba_request *req)
{
unsigned int transaction_len;
@@ -1457,7 +1479,7 @@
DBG(DBG_HW, "Packet length: %u\n", pkt_len);
if (pkt_len != sizeof(crq)) {
pr_warning("udc: Invalid packet length %u "
- "(expected %lu)\n", pkt_len, sizeof(crq));
+ "(expected %zu)\n", pkt_len, sizeof(crq));
set_protocol_stall(udc, ep);
return;
}
@@ -1615,6 +1637,7 @@
DBG(DBG_INT, "irq, status=%#08x\n", status);
if (status & USBA_DET_SUSPEND) {
+ toggle_bias(0);
usba_writel(udc, INT_CLR, USBA_DET_SUSPEND);
DBG(DBG_BUS, "Suspend detected\n");
if (udc->gadget.speed != USB_SPEED_UNKNOWN
@@ -1626,6 +1649,7 @@
}
if (status & USBA_WAKE_UP) {
+ toggle_bias(1);
usba_writel(udc, INT_CLR, USBA_WAKE_UP);
DBG(DBG_BUS, "Wake Up CPU detected\n");
}
@@ -1719,12 +1743,14 @@
vbus = gpio_get_value(udc->vbus_pin);
if (vbus != udc->vbus_prev) {
if (vbus) {
- usba_writel(udc, CTRL, USBA_EN_USBA);
+ toggle_bias(1);
+ usba_writel(udc, CTRL, USBA_ENABLE_MASK);
usba_writel(udc, INT_ENB, USBA_END_OF_RESET);
} else {
udc->gadget.speed = USB_SPEED_UNKNOWN;
reset_all_endpoints(udc);
- usba_writel(udc, CTRL, 0);
+ toggle_bias(0);
+ usba_writel(udc, CTRL, USBA_DISABLE_MASK);
spin_unlock(&udc->lock);
udc->driver->disconnect(&udc->gadget);
spin_lock(&udc->lock);
@@ -1777,7 +1803,8 @@
/* If Vbus is present, enable the controller and wait for reset */
spin_lock_irqsave(&udc->lock, flags);
if (vbus_is_present(udc) && udc->vbus_prev == 0) {
- usba_writel(udc, CTRL, USBA_EN_USBA);
+ toggle_bias(1);
+ usba_writel(udc, CTRL, USBA_ENABLE_MASK);
usba_writel(udc, INT_ENB, USBA_END_OF_RESET);
}
spin_unlock_irqrestore(&udc->lock, flags);
@@ -1810,7 +1837,8 @@
spin_unlock_irqrestore(&udc->lock, flags);
/* This will also disable the DP pullup */
- usba_writel(udc, CTRL, 0);
+ toggle_bias(0);
+ usba_writel(udc, CTRL, USBA_DISABLE_MASK);
driver->unbind(&udc->gadget);
udc->gadget.dev.driver = NULL;
@@ -1880,7 +1908,8 @@
/* Make sure we start from a clean slate */
clk_enable(pclk);
- usba_writel(udc, CTRL, 0);
+ toggle_bias(0);
+ usba_writel(udc, CTRL, USBA_DISABLE_MASK);
clk_disable(pclk);
usba_ep = kmalloc(sizeof(struct usba_ep) * pdata->num_ep,