Staging: rtl8192su: remove RTL8192SU_ASIC_VERIFICATION ifdefs
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/staging/rtl8192su/Makefile b/drivers/staging/rtl8192su/Makefile
index 02d4614..58073da4 100644
--- a/drivers/staging/rtl8192su/Makefile
+++ b/drivers/staging/rtl8192su/Makefile
@@ -12,7 +12,6 @@
EXTRA_CFLAGS += -DRTL8192S_PREPARE_FOR_NORMAL_RELEASE
EXTRA_CFLAGS += -DRTL8192SU_DISABLE_IQK=1
-EXTRA_CFLAGS += -DRTL8192SU_ASIC_VERIFICATION
EXTRA_CFLAGS += -DRTL8192SU_USB_PHY_TEST=0
#EXTRA_CFLAGS += -DMUTIPLE_BULK_OUT
diff --git a/drivers/staging/rtl8192su/r8192S_firmware.c b/drivers/staging/rtl8192su/r8192S_firmware.c
index 287927b..8ca173e 100644
--- a/drivers/staging/rtl8192su/r8192S_firmware.c
+++ b/drivers/staging/rtl8192su/r8192S_firmware.c
@@ -320,13 +320,11 @@
RT_TRACE(COMP_FIRMWARE, "FirmwareCheckReady(): Current RCR settings(%#x)\n", tmpU4b);
-#if defined (RTL8192SU_ASIC_VERIFICATION)
#ifdef NOT_YET //YJ,TMP
priv->TransmitConfig = read_nic_dword(dev, TCR);
RT_TRACE(COMP_FIRMWARE, "FirmwareCheckReady(): Current TCR settings(%x)\n", priv->TransmitConfig);
pHalData->FwRsvdTxPageCfg = read_nic_byte(dev, FW_RSVD_PG_CRTL);
#endif
-#endif
// Set to normal mode.
write_nic_byte(dev, LBKMD_SEL, LBK_NORMAL);
diff --git a/drivers/staging/rtl8192su/r8192U_core.c b/drivers/staging/rtl8192su/r8192U_core.c
index 37abb6811..55aeaf6 100644
--- a/drivers/staging/rtl8192su/r8192U_core.c
+++ b/drivers/staging/rtl8192su/r8192U_core.c
@@ -2957,9 +2957,7 @@
memset(tx_desc, 0, sizeof(tx_desc_819x_usb));
-#if defined (RTL8192SU_ASIC_VERIFICATION)
tx_desc->NonQos = (IsQoSDataFrame(skb->data)==TRUE)? 0:1;
-#endif
/* Fill Tx descriptor */
//memset(tx_fwinfo,0,sizeof(tx_fwinfo_819x_usb));
@@ -4029,9 +4027,7 @@
int wpa_ie_len= ieee->wpa_ie_len;
struct ieee80211_crypt_data* crypt;
int encrypt;
-#if defined (RTL8192SU_ASIC_VERIFICATION)
return TRUE;
-#endif
crypt = ieee->crypt[ieee->tx_keyidx];
//we use connecting AP's capability instead of only security config on our driver to distinguish whether it should use N mode or G mode
@@ -4883,13 +4879,9 @@
RT_TRACE(COMP_EPROM, "MAC addr:"MAC_FMT"\n", MAC_ARG(dev->dev_addr));
priv->rf_type = RTL819X_DEFAULT_RF_TYPE; //default 1T2R
-#if defined (RTL8192SU_ASIC_VERIFICATION)
priv->rf_chip = RF_6052;
priv->rf_type = RTL819X_DEFAULT_RF_TYPE;
//priv->card_8192_version = VERSION_8192SU_A; //Over write for temporally experiment. 2008.10.16. By Roger.
-#else
- priv->rf_chip = RF_8256;
-#endif
{
#if 0
@@ -5215,12 +5207,8 @@
// 2007/11/15 MH For RTL8192USB we assign as 1T2R now.
priv->rf_type = RTL819X_DEFAULT_RF_TYPE; // default : 1T2R
-#if defined (RTL8192SU_ASIC_VERIFICATION)
priv->rf_chip = RF_6052;
priv->rf_type = RTL819X_DEFAULT_RF_TYPE;
-#else
- priv->rf_chip = RF_8256;
-#endif
{
//
@@ -5660,11 +5648,7 @@
// priv->rf_type = RF_1T2R;
//}
-#if defined (RTL8192SU_ASIC_VERIFICATION)
priv->rf_chip = RF_6052;
-#else
- priv->rf_chip = RF_8256;
-#endif
priv->rf_chip = RF_6052;//lzm test
RT_TRACE(COMP_INIT, "BoardType = 0x%2x\n", priv->EEPROMBoardType);
@@ -7778,9 +7762,7 @@
RESET_TYPE RxResetType = RESET_TYPE_NORESET;
RT_RF_POWER_STATE rfState;
-#if defined (RTL8192SU_ASIC_VERIFICATION)
return RESET_TYPE_NORESET;
-#endif
rfState = priv->ieee80211->eRFPowerState;