arch/arm/mach-davinci/board-omapl138-hawk.c - kernel/msm-4.9 - Gitiles

 /*
  * Hawkboard.org based on TI's OMAP-L138 Platform
  *
  * Initial code: Syed Mohammed Khasim
  *
  * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com
  *
  * This file is licensed under the terms of the GNU General Public License
  * version 2. This program is licensed "as is" without any warranty of
  * any kind, whether express or implied.
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/console.h>
 #include <linux/gpio.h>

 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>

 #include <mach/cp_intc.h>
 #include <mach/da8xx.h>
 #include <mach/mux.h>

 #define HAWKBOARD_PHY_ID		"0:07"
 #define DA850_HAWK_MMCSD_CD_PIN		GPIO_TO_PIN(3, 12)
 #define DA850_HAWK_MMCSD_WP_PIN		GPIO_TO_PIN(3, 13)

 #define DA850_USB1_VBUS_PIN		GPIO_TO_PIN(2, 4)
 #define DA850_USB1_OC_PIN		GPIO_TO_PIN(6, 13)

 static short omapl138_hawk_mii_pins[] __initdata = {
 	DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
 	DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
 	DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
 	DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
 	DA850_MDIO_D,
 	-1
 };

 static __init void omapl138_hawk_config_emac(void)
 {
 	void __iomem *cfgchip3 = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
 	int ret;
 	u32 val;
 	struct davinci_soc_info *soc_info = &davinci_soc_info;

 	val = __raw_readl(cfgchip3);
 	val &= ~BIT(8);
 	ret = davinci_cfg_reg_list(omapl138_hawk_mii_pins);
 	if (ret) {
 		pr_warning("%s: cpgmac/mii mux setup failed: %d\n",
 			__func__, ret);
 		return;
 	}

 	/* configure the CFGCHIP3 register for MII */
 	__raw_writel(val, cfgchip3);
 	pr_info("EMAC: MII PHY configured\n");

 	soc_info->emac_pdata->phy_id = HAWKBOARD_PHY_ID;

 	ret = da8xx_register_emac();
 	if (ret)
 		pr_warning("%s: emac registration failed: %d\n",
 			__func__, ret);
 }

 /*
  * The following EDMA channels/slots are not being used by drivers (for
  * example: Timer, GPIO, UART events etc) on da850/omap-l138 EVM/Hawkboard,
  * hence they are being reserved for codecs on the DSP side.
  */
 static const s16 da850_dma0_rsv_chans[][2] = {
 	/* (offset, number) */
 	{ 8,  6},
 	{24,  4},
 	{30,  2},
 	{-1, -1}
 };

 static const s16 da850_dma0_rsv_slots[][2] = {
 	/* (offset, number) */
 	{ 8,  6},
 	{24,  4},
 	{30, 50},
 	{-1, -1}
 };

 static const s16 da850_dma1_rsv_chans[][2] = {
 	/* (offset, number) */
 	{ 0, 28},
 	{30,  2},
 	{-1, -1}
 };

 static const s16 da850_dma1_rsv_slots[][2] = {
 	/* (offset, number) */
 	{ 0, 28},
 	{30, 90},
 	{-1, -1}
 };

 static struct edma_rsv_info da850_edma_cc0_rsv = {
 	.rsv_chans	= da850_dma0_rsv_chans,
 	.rsv_slots	= da850_dma0_rsv_slots,
 };

 static struct edma_rsv_info da850_edma_cc1_rsv = {
 	.rsv_chans	= da850_dma1_rsv_chans,
 	.rsv_slots	= da850_dma1_rsv_slots,
 };

 static struct edma_rsv_info *da850_edma_rsv[2] = {
 	&da850_edma_cc0_rsv,
 	&da850_edma_cc1_rsv,
 };

 static const short hawk_mmcsd0_pins[] = {
 	DA850_MMCSD0_DAT_0, DA850_MMCSD0_DAT_1, DA850_MMCSD0_DAT_2,
 	DA850_MMCSD0_DAT_3, DA850_MMCSD0_CLK, DA850_MMCSD0_CMD,
 	DA850_GPIO3_12, DA850_GPIO3_13,
 	-1
 };

 static int da850_hawk_mmc_get_ro(int index)
 {
 	return gpio_get_value(DA850_HAWK_MMCSD_WP_PIN);
 }

 static int da850_hawk_mmc_get_cd(int index)
 {
 	return !gpio_get_value(DA850_HAWK_MMCSD_CD_PIN);
 }

 static struct davinci_mmc_config da850_mmc_config = {
 	.get_ro		= da850_hawk_mmc_get_ro,
 	.get_cd		= da850_hawk_mmc_get_cd,
 	.wires		= 4,
 	.max_freq	= 50000000,
 	.caps		= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
 	.version	= MMC_CTLR_VERSION_2,
 };

 static __init void omapl138_hawk_mmc_init(void)
 {
 	int ret;

 	ret = davinci_cfg_reg_list(hawk_mmcsd0_pins);
 	if (ret) {
 		pr_warning("%s: MMC/SD0 mux setup failed: %d\n",
 			__func__, ret);
 		return;
 	}

 	ret = gpio_request_one(DA850_HAWK_MMCSD_CD_PIN,
 			GPIOF_DIR_IN, "MMC CD");
 	if (ret < 0) {
 		pr_warning("%s: can not open GPIO %d\n",
 			__func__, DA850_HAWK_MMCSD_CD_PIN);
 		return;
 	}

 	ret = gpio_request_one(DA850_HAWK_MMCSD_WP_PIN,
 			GPIOF_DIR_IN, "MMC WP");
 	if (ret < 0) {
 		pr_warning("%s: can not open GPIO %d\n",
 			__func__, DA850_HAWK_MMCSD_WP_PIN);
 		goto mmc_setup_wp_fail;
 	}

 	ret = da8xx_register_mmcsd0(&da850_mmc_config);
 	if (ret) {
 		pr_warning("%s: MMC/SD0 registration failed: %d\n",
 			__func__, ret);
 		goto mmc_setup_mmcsd_fail;
 	}

 	return;

 mmc_setup_mmcsd_fail:
 	gpio_free(DA850_HAWK_MMCSD_WP_PIN);
 mmc_setup_wp_fail:
 	gpio_free(DA850_HAWK_MMCSD_CD_PIN);
 }

 static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id);
 static da8xx_ocic_handler_t hawk_usb_ocic_handler;

 static const short da850_hawk_usb11_pins[] = {
 	DA850_GPIO2_4, DA850_GPIO6_13,
 	-1
 };

 static int hawk_usb_set_power(unsigned port, int on)
 {
 	gpio_set_value(DA850_USB1_VBUS_PIN, on);
 	return 0;
 }

 static int hawk_usb_get_power(unsigned port)
 {
 	return gpio_get_value(DA850_USB1_VBUS_PIN);
 }

 static int hawk_usb_get_oci(unsigned port)
 {
 	return !gpio_get_value(DA850_USB1_OC_PIN);
 }

 static int hawk_usb_ocic_notify(da8xx_ocic_handler_t handler)
 {
 	int irq         = gpio_to_irq(DA850_USB1_OC_PIN);
 	int error       = 0;

 	if (handler != NULL) {
 		hawk_usb_ocic_handler = handler;

 		error = request_irq(irq, omapl138_hawk_usb_ocic_irq,
 					IRQF_DISABLED | IRQF_TRIGGER_RISING |
 					IRQF_TRIGGER_FALLING,
 					"OHCI over-current indicator", NULL);
 		if (error)
 			pr_err("%s: could not request IRQ to watch "
 				"over-current indicator changes\n", __func__);
 	} else {
 		free_irq(irq, NULL);
 	}
 	return error;
 }

 static struct da8xx_ohci_root_hub omapl138_hawk_usb11_pdata = {
 	.set_power      = hawk_usb_set_power,
 	.get_power      = hawk_usb_get_power,
 	.get_oci        = hawk_usb_get_oci,
 	.ocic_notify    = hawk_usb_ocic_notify,
 	/* TPS2087 switch @ 5V */
 	.potpgt         = (3 + 1) / 2,  /* 3 ms max */
 };

 static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id)
 {
 	hawk_usb_ocic_handler(&omapl138_hawk_usb11_pdata, 1);
 	return IRQ_HANDLED;
 }

 static __init void omapl138_hawk_usb_init(void)
 {
 	int ret;
 	u32 cfgchip2;

 	ret = davinci_cfg_reg_list(da850_hawk_usb11_pins);
 	if (ret) {
 		pr_warning("%s: USB 1.1 PinMux setup failed: %d\n",
 			__func__, ret);
 		return;
 	}

 	/* Setup the Ref. clock frequency for the HAWK at 24 MHz. */

 	cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
 	cfgchip2 &= ~CFGCHIP2_REFFREQ;
 	cfgchip2 |=  CFGCHIP2_REFFREQ_24MHZ;
 	__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));

 	ret = gpio_request_one(DA850_USB1_VBUS_PIN,
 			GPIOF_DIR_OUT, "USB1 VBUS");
 	if (ret < 0) {
 		pr_err("%s: failed to request GPIO for USB 1.1 port "
 			"power control: %d\n", __func__, ret);
 		return;
 	}

 	ret = gpio_request_one(DA850_USB1_OC_PIN,
 			GPIOF_DIR_IN, "USB1 OC");
 	if (ret < 0) {
 		pr_err("%s: failed to request GPIO for USB 1.1 port "
 			"over-current indicator: %d\n", __func__, ret);
 		goto usb11_setup_oc_fail;
 	}

 	ret = da8xx_register_usb11(&omapl138_hawk_usb11_pdata);
 	if (ret) {
 		pr_warning("%s: USB 1.1 registration failed: %d\n",
 			__func__, ret);
 		goto usb11_setup_fail;
 	}

 	return;

 usb11_setup_fail:
 	gpio_free(DA850_USB1_OC_PIN);
 usb11_setup_oc_fail:
 	gpio_free(DA850_USB1_VBUS_PIN);
 }

 static struct davinci_uart_config omapl138_hawk_uart_config __initdata = {
 	.enabled_uarts = 0x7,
 };

 static __init void omapl138_hawk_init(void)
 {
 	int ret;

 	davinci_serial_init(&omapl138_hawk_uart_config);

 	omapl138_hawk_config_emac();

 	ret = da850_register_edma(da850_edma_rsv);
 	if (ret)
 		pr_warning("%s: EDMA registration failed: %d\n",
 			__func__, ret);

 	omapl138_hawk_mmc_init();

 	omapl138_hawk_usb_init();

 	ret = da8xx_register_watchdog();
 	if (ret)
 		pr_warning("omapl138_hawk_init: "
 			"watchdog registration failed: %d\n",
 			ret);
 }

 #ifdef CONFIG_SERIAL_8250_CONSOLE
 static int __init omapl138_hawk_console_init(void)
 {
 	if (!machine_is_omapl138_hawkboard())
 		return 0;

 	return add_preferred_console("ttyS", 2, "115200");
 }
 console_initcall(omapl138_hawk_console_init);
 #endif

 static void __init omapl138_hawk_map_io(void)
 {
 	da850_init();
 }

 MACHINE_START(OMAPL138_HAWKBOARD, "AM18x/OMAP-L138 Hawkboard")
 	.atag_offset	= 0x100,
 	.map_io		= omapl138_hawk_map_io,
 	.init_irq	= cp_intc_init,
 	.timer		= &davinci_timer,
 	.init_machine	= omapl138_hawk_init,
 	.dma_zone_size	= SZ_128M,
 	.restart	= da8xx_restart,
 MACHINE_END
	/*
	* Hawkboard.org based on TI's OMAP-L138 Platform
	*
	* Initial code: Syed Mohammed Khasim
	*
	* Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com
	*
	* This file is licensed under the terms of the GNU General Public License
	* version 2. This program is licensed "as is" without any warranty of
	* any kind, whether express or implied.
	*/
	#include <linux/kernel.h>
	#include <linux/init.h>
	#include <linux/console.h>
	#include <linux/gpio.h>

	#include <asm/mach-types.h>
	#include <asm/mach/arch.h>

	#include <mach/cp_intc.h>
	#include <mach/da8xx.h>
	#include <mach/mux.h>

	#define HAWKBOARD_PHY_ID "0:07"
	#define DA850_HAWK_MMCSD_CD_PIN GPIO_TO_PIN(3, 12)
	#define DA850_HAWK_MMCSD_WP_PIN GPIO_TO_PIN(3, 13)

	#define DA850_USB1_VBUS_PIN GPIO_TO_PIN(2, 4)
	#define DA850_USB1_OC_PIN GPIO_TO_PIN(6, 13)

	static short omapl138_hawk_mii_pins[] __initdata = {
	DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
	DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
	DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
	DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
	DA850_MDIO_D,
	-1
	};

	static __init void omapl138_hawk_config_emac(void)
	{
	void __iomem *cfgchip3 = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
	int ret;
	u32 val;
	struct davinci_soc_info *soc_info = &davinci_soc_info;

	val = __raw_readl(cfgchip3);
	val &= ~BIT(8);
	ret = davinci_cfg_reg_list(omapl138_hawk_mii_pins);
	if (ret) {
	pr_warning("%s: cpgmac/mii mux setup failed: %d\n",
	__func__, ret);
	return;
	}

	/* configure the CFGCHIP3 register for MII */
	__raw_writel(val, cfgchip3);
	pr_info("EMAC: MII PHY configured\n");

	soc_info->emac_pdata->phy_id = HAWKBOARD_PHY_ID;

	ret = da8xx_register_emac();
	if (ret)
	pr_warning("%s: emac registration failed: %d\n",
	__func__, ret);
	}

	/*
	* The following EDMA channels/slots are not being used by drivers (for
	* example: Timer, GPIO, UART events etc) on da850/omap-l138 EVM/Hawkboard,
	* hence they are being reserved for codecs on the DSP side.
	*/
	static const s16 da850_dma0_rsv_chans[][2] = {
	/* (offset, number) */
	{ 8, 6},
	{24, 4},
	{30, 2},
	{-1, -1}
	};

	static const s16 da850_dma0_rsv_slots[][2] = {
	/* (offset, number) */
	{ 8, 6},
	{24, 4},
	{30, 50},
	{-1, -1}
	};

	static const s16 da850_dma1_rsv_chans[][2] = {
	/* (offset, number) */
	{ 0, 28},
	{30, 2},
	{-1, -1}
	};

	static const s16 da850_dma1_rsv_slots[][2] = {
	/* (offset, number) */
	{ 0, 28},
	{30, 90},
	{-1, -1}
	};

	static struct edma_rsv_info da850_edma_cc0_rsv = {
	.rsv_chans = da850_dma0_rsv_chans,
	.rsv_slots = da850_dma0_rsv_slots,
	};

	static struct edma_rsv_info da850_edma_cc1_rsv = {
	.rsv_chans = da850_dma1_rsv_chans,
	.rsv_slots = da850_dma1_rsv_slots,
	};

	static struct edma_rsv_info *da850_edma_rsv[2] = {
	&da850_edma_cc0_rsv,
	&da850_edma_cc1_rsv,
	};

	static const short hawk_mmcsd0_pins[] = {
	DA850_MMCSD0_DAT_0, DA850_MMCSD0_DAT_1, DA850_MMCSD0_DAT_2,
	DA850_MMCSD0_DAT_3, DA850_MMCSD0_CLK, DA850_MMCSD0_CMD,
	DA850_GPIO3_12, DA850_GPIO3_13,
	-1
	};

	static int da850_hawk_mmc_get_ro(int index)
	{
	return gpio_get_value(DA850_HAWK_MMCSD_WP_PIN);
	}

	static int da850_hawk_mmc_get_cd(int index)
	{
	return !gpio_get_value(DA850_HAWK_MMCSD_CD_PIN);
	}

	static struct davinci_mmc_config da850_mmc_config = {
	.get_ro = da850_hawk_mmc_get_ro,
	.get_cd = da850_hawk_mmc_get_cd,
	.wires = 4,
	.max_freq = 50000000,
	.caps = MMC_CAP_MMC_HIGHSPEED \| MMC_CAP_SD_HIGHSPEED,
	.version = MMC_CTLR_VERSION_2,
	};

	static __init void omapl138_hawk_mmc_init(void)
	{
	int ret;

	ret = davinci_cfg_reg_list(hawk_mmcsd0_pins);
	if (ret) {
	pr_warning("%s: MMC/SD0 mux setup failed: %d\n",
	__func__, ret);
	return;
	}

	ret = gpio_request_one(DA850_HAWK_MMCSD_CD_PIN,
	GPIOF_DIR_IN, "MMC CD");
	if (ret < 0) {
	pr_warning("%s: can not open GPIO %d\n",
	__func__, DA850_HAWK_MMCSD_CD_PIN);
	return;
	}

	ret = gpio_request_one(DA850_HAWK_MMCSD_WP_PIN,
	GPIOF_DIR_IN, "MMC WP");
	if (ret < 0) {
	pr_warning("%s: can not open GPIO %d\n",
	__func__, DA850_HAWK_MMCSD_WP_PIN);
	goto mmc_setup_wp_fail;
	}

	ret = da8xx_register_mmcsd0(&da850_mmc_config);
	if (ret) {
	pr_warning("%s: MMC/SD0 registration failed: %d\n",
	__func__, ret);
	goto mmc_setup_mmcsd_fail;
	}

	return;

	mmc_setup_mmcsd_fail:
	gpio_free(DA850_HAWK_MMCSD_WP_PIN);
	mmc_setup_wp_fail:
	gpio_free(DA850_HAWK_MMCSD_CD_PIN);
	}

	static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id);
	static da8xx_ocic_handler_t hawk_usb_ocic_handler;

	static const short da850_hawk_usb11_pins[] = {
	DA850_GPIO2_4, DA850_GPIO6_13,
	-1
	};

	static int hawk_usb_set_power(unsigned port, int on)
	{
	gpio_set_value(DA850_USB1_VBUS_PIN, on);
	return 0;
	}

	static int hawk_usb_get_power(unsigned port)
	{
	return gpio_get_value(DA850_USB1_VBUS_PIN);
	}

	static int hawk_usb_get_oci(unsigned port)
	{
	return !gpio_get_value(DA850_USB1_OC_PIN);
	}

	static int hawk_usb_ocic_notify(da8xx_ocic_handler_t handler)
	{
	int irq = gpio_to_irq(DA850_USB1_OC_PIN);
	int error = 0;

	if (handler != NULL) {
	hawk_usb_ocic_handler = handler;

	error = request_irq(irq, omapl138_hawk_usb_ocic_irq,
	IRQF_DISABLED \| IRQF_TRIGGER_RISING \|
	IRQF_TRIGGER_FALLING,
	"OHCI over-current indicator", NULL);
	if (error)
	pr_err("%s: could not request IRQ to watch "
	"over-current indicator changes\n", __func__);
	} else {
	free_irq(irq, NULL);
	}
	return error;
	}

	static struct da8xx_ohci_root_hub omapl138_hawk_usb11_pdata = {
	.set_power = hawk_usb_set_power,
	.get_power = hawk_usb_get_power,
	.get_oci = hawk_usb_get_oci,
	.ocic_notify = hawk_usb_ocic_notify,
	/* TPS2087 switch @ 5V */
	.potpgt = (3 + 1) / 2, /* 3 ms max */
	};

	static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id)
	{
	hawk_usb_ocic_handler(&omapl138_hawk_usb11_pdata, 1);
	return IRQ_HANDLED;
	}

	static __init void omapl138_hawk_usb_init(void)
	{
	int ret;
	u32 cfgchip2;

	ret = davinci_cfg_reg_list(da850_hawk_usb11_pins);
	if (ret) {
	pr_warning("%s: USB 1.1 PinMux setup failed: %d\n",
	__func__, ret);
	return;
	}

	/* Setup the Ref. clock frequency for the HAWK at 24 MHz. */

	cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
	cfgchip2 &= ~CFGCHIP2_REFFREQ;
	cfgchip2 \|= CFGCHIP2_REFFREQ_24MHZ;
	__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));

	ret = gpio_request_one(DA850_USB1_VBUS_PIN,
	GPIOF_DIR_OUT, "USB1 VBUS");
	if (ret < 0) {
	pr_err("%s: failed to request GPIO for USB 1.1 port "
	"power control: %d\n", __func__, ret);
	return;
	}

	ret = gpio_request_one(DA850_USB1_OC_PIN,
	GPIOF_DIR_IN, "USB1 OC");
	if (ret < 0) {
	pr_err("%s: failed to request GPIO for USB 1.1 port "
	"over-current indicator: %d\n", __func__, ret);
	goto usb11_setup_oc_fail;
	}

	ret = da8xx_register_usb11(&omapl138_hawk_usb11_pdata);
	if (ret) {
	pr_warning("%s: USB 1.1 registration failed: %d\n",
	__func__, ret);
	goto usb11_setup_fail;
	}

	return;

	usb11_setup_fail:
	gpio_free(DA850_USB1_OC_PIN);
	usb11_setup_oc_fail:
	gpio_free(DA850_USB1_VBUS_PIN);
	}

	static struct davinci_uart_config omapl138_hawk_uart_config __initdata = {
	.enabled_uarts = 0x7,
	};

	static __init void omapl138_hawk_init(void)
	{
	int ret;

	davinci_serial_init(&omapl138_hawk_uart_config);

	omapl138_hawk_config_emac();

	ret = da850_register_edma(da850_edma_rsv);
	if (ret)
	pr_warning("%s: EDMA registration failed: %d\n",
	__func__, ret);

	omapl138_hawk_mmc_init();

	omapl138_hawk_usb_init();

	ret = da8xx_register_watchdog();
	if (ret)
	pr_warning("omapl138_hawk_init: "
	"watchdog registration failed: %d\n",
	ret);
	}

	#ifdef CONFIG_SERIAL_8250_CONSOLE
	static int __init omapl138_hawk_console_init(void)
	{
	if (!machine_is_omapl138_hawkboard())
	return 0;

	return add_preferred_console("ttyS", 2, "115200");
	}
	console_initcall(omapl138_hawk_console_init);
	#endif

	static void __init omapl138_hawk_map_io(void)
	{
	da850_init();
	}

	MACHINE_START(OMAPL138_HAWKBOARD, "AM18x/OMAP-L138 Hawkboard")
	.atag_offset = 0x100,
	.map_io = omapl138_hawk_map_io,
	.init_irq = cp_intc_init,
	.timer = &davinci_timer,
	.init_machine = omapl138_hawk_init,
	.dma_zone_size = SZ_128M,
	.restart = da8xx_restart,
	MACHINE_END