Blackfin arch: unify the duplicated portions of __start and split mach-specific pieces into _mach_early_start where they will be easier to trim over time
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
diff --git a/arch/blackfin/mach-bf561/head.S b/arch/blackfin/mach-bf561/head.S
index c541b31..fe6f979 100644
--- a/arch/blackfin/mach-bf561/head.S
+++ b/arch/blackfin/mach-bf561/head.S
@@ -30,93 +30,16 @@
#include <linux/linkage.h>
#include <linux/init.h>
#include <asm/blackfin.h>
-#include <asm/trace.h>
-
-#if CONFIG_BFIN_KERNEL_CLOCK
+#ifdef CONFIG_BFIN_KERNEL_CLOCK
#include <asm/mach-common/clocks.h>
#include <asm/mach/mem_init.h>
#endif
-.extern ___bss_stop
-.extern ___bss_start
.extern _bf53x_relocate_l1_mem
-#define INITIAL_STACK 0xFFB01000
-
__INIT
-ENTRY(__start)
- /* R0: argument of command line string, passed from uboot, save it */
- R7 = R0;
- /* Enable Cycle Counter and Nesting Of Interrupts */
-#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES
- R0 = SYSCFG_SNEN;
-#else
- R0 = SYSCFG_SNEN | SYSCFG_CCEN;
-#endif
- SYSCFG = R0;
- R0 = 0;
-
- /* Clear Out All the data and pointer Registers */
- R1 = R0;
- R2 = R0;
- R3 = R0;
- R4 = R0;
- R5 = R0;
- R6 = R0;
-
- P0 = R0;
- P1 = R0;
- P2 = R0;
- P3 = R0;
- P4 = R0;
- P5 = R0;
-
- LC0 = r0;
- LC1 = r0;
- L0 = r0;
- L1 = r0;
- L2 = r0;
- L3 = r0;
-
- /* Clear Out All the DAG Registers */
- B0 = r0;
- B1 = r0;
- B2 = r0;
- B3 = r0;
-
- I0 = r0;
- I1 = r0;
- I2 = r0;
- I3 = r0;
-
- M0 = r0;
- M1 = r0;
- M2 = r0;
- M3 = r0;
-
- trace_buffer_init(p0,r0);
- P0 = R1;
- R0 = R1;
-
- /* Turn off the icache */
- p0.l = LO(IMEM_CONTROL);
- p0.h = HI(IMEM_CONTROL);
- R1 = [p0];
- R0 = ~ENICPLB;
- R0 = R0 & R1;
- [p0] = R0;
- SSYNC;
-
- /* Turn off the dcache */
- p0.l = LO(DMEM_CONTROL);
- p0.h = HI(DMEM_CONTROL);
- R1 = [p0];
- R0 = ~ENDCPLB;
- R0 = R0 & R1;
- [p0] = R0;
- SSYNC;
-
+ENTRY(_mach_early_start)
/* Initialise UART - when booting from u-boot, the UART is not disabled
* so if we dont initalize here, our serial console gets hosed */
p0.h = hi(BFIN_UART_LCR);
@@ -143,62 +66,13 @@
w[p0] = r0.L; /* To enable UART clock */
ssync;
- /* Initialize stack pointer */
- sp.l = lo(INITIAL_STACK);
- sp.h = hi(INITIAL_STACK);
- fp = sp;
- usp = sp;
-
-#ifdef CONFIG_EARLY_PRINTK
- SP += -12;
- call _init_early_exception_vectors;
- SP += 12;
-#endif
-
- /* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */
- call _bf53x_relocate_l1_mem;
-#if CONFIG_BFIN_KERNEL_CLOCK
- call _start_dma_code;
-#endif
-
- /* This section keeps the processor in supervisor mode
- * during kernel boot. Switches to user mode at end of boot.
- * See page 3-9 of Hardware Reference manual for documentation.
- */
-
- /* EVT15 = _real_start */
-
- p0.l = lo(EVT15);
- p0.h = hi(EVT15);
- p1.l = _real_start;
- p1.h = _real_start;
- [p0] = p1;
- csync;
-
- p0.l = lo(IMASK);
- p0.h = hi(IMASK);
- p1.l = IMASK_IVG15;
- p1.h = 0x0;
- [p0] = p1;
- csync;
-
- raise 15;
- p0.l = .LWAIT_HERE;
- p0.h = .LWAIT_HERE;
- reti = p0;
-#if ANOMALY_05000281
- nop; nop; nop;
-#endif
- rti;
-
-.LWAIT_HERE:
- jump .LWAIT_HERE;
-ENDPROC(__start)
+ rts;
+ENDPROC(_mach_early_start)
__FINIT
.section .l1.text
-#if CONFIG_BFIN_KERNEL_CLOCK
+#ifdef CONFIG_BFIN_KERNEL_CLOCK
ENTRY(_start_dma_code)
p0.h = hi(SICA_IWR0);
p0.l = lo(SICA_IWR0);