| /* |
| * max8997.h - Driver for the Maxim 8997/8966 |
| * |
| * Copyright (C) 2009-2010 Samsung Electrnoics |
| * MyungJoo Ham <myungjoo.ham@samsung.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA |
| * |
| * This driver is based on max8998.h |
| * |
| * MAX8997 has PMIC, MUIC, HAPTIC, RTC, FLASH, and Fuel Gauge devices. |
| * Except Fuel Gauge, every device shares the same I2C bus and included in |
| * this mfd driver. Although the fuel gauge is included in the chip, it is |
| * excluded from the driver because a) it has a different I2C bus from |
| * others and b) it can be enabled simply by using MAX17042 driver. |
| */ |
| |
| #ifndef __LINUX_MFD_MAX8998_H |
| #define __LINUX_MFD_MAX8998_H |
| |
| #include <linux/regulator/consumer.h> |
| |
| /* MAX8997/8966 regulator IDs */ |
| enum max8998_regulators { |
| MAX8997_LDO1 = 0, |
| MAX8997_LDO2, |
| MAX8997_LDO3, |
| MAX8997_LDO4, |
| MAX8997_LDO5, |
| MAX8997_LDO6, |
| MAX8997_LDO7, |
| MAX8997_LDO8, |
| MAX8997_LDO9, |
| MAX8997_LDO10, |
| MAX8997_LDO11, |
| MAX8997_LDO12, |
| MAX8997_LDO13, |
| MAX8997_LDO14, |
| MAX8997_LDO15, |
| MAX8997_LDO16, |
| MAX8997_LDO17, |
| MAX8997_LDO18, |
| MAX8997_LDO21, |
| MAX8997_BUCK1, |
| MAX8997_BUCK2, |
| MAX8997_BUCK3, |
| MAX8997_BUCK4, |
| MAX8997_BUCK5, |
| MAX8997_BUCK6, |
| MAX8997_BUCK7, |
| MAX8997_EN32KHZ_AP, |
| MAX8997_EN32KHZ_CP, |
| MAX8997_ENVICHG, |
| MAX8997_ESAFEOUT1, |
| MAX8997_ESAFEOUT2, |
| MAX8997_CHARGER_CV, /* control MBCCV of MBCCTRL3 */ |
| MAX8997_CHARGER, /* charger current, MBCCTRL4 */ |
| MAX8997_CHARGER_TOPOFF, /* MBCCTRL5 */ |
| |
| MAX8997_REG_MAX, |
| }; |
| |
| struct max8997_regulator_data { |
| int id; |
| struct regulator_init_data *initdata; |
| }; |
| |
| struct max8997_platform_data { |
| /* IRQ */ |
| int irq_base; |
| int ono; |
| int wakeup; |
| |
| /* ---- PMIC ---- */ |
| struct max8997_regulator_data *regulators; |
| int num_regulators; |
| |
| /* |
| * SET1~3 DVS GPIOs control Buck1, 2, and 5 simultaneously. Therefore, |
| * With buckx_gpiodvs enabled, the buckx cannot be controlled |
| * independently. To control buckx (of 1, 2, and 5) independently, |
| * disable buckx_gpiodvs and control with BUCKxDVS1 register. |
| * |
| * When buckx_gpiodvs and bucky_gpiodvs are both enabled, set_voltage |
| * on buckx will change the voltage of bucky at the same time. |
| * |
| */ |
| bool ignore_gpiodvs_side_effect; |
| int buck125_gpios[3]; /* GPIO of [0]SET1, [1]SET2, [2]SET3 */ |
| int buck125_default_idx; /* Default value of SET1, 2, 3 */ |
| unsigned int buck1_voltage[8]; /* buckx_voltage in uV */ |
| bool buck1_gpiodvs; |
| unsigned int buck2_voltage[8]; |
| bool buck2_gpiodvs; |
| unsigned int buck5_voltage[8]; |
| bool buck5_gpiodvs; |
| |
| /* MUIC: Not implemented */ |
| /* HAPTIC: Not implemented */ |
| /* RTC: Not implemented */ |
| /* Flash: Not implemented */ |
| /* Charger control: Not implemented */ |
| }; |
| |
| #endif /* __LINUX_MFD_MAX8998_H */ |