diff --git a/drivers/scsi/ncr53c8xx.h b/drivers/scsi/ncr53c8xx.h
index 05c7b83..6a7bef2 100644
--- a/drivers/scsi/ncr53c8xx.h
+++ b/drivers/scsi/ncr53c8xx.h
@@ -2,6 +2,7 @@
 **  Device driver for the PCI-SCSI NCR538XX controller family.
 **
 **  Copyright (C) 1994  Wolfgang Stanglmeier
+**  Copyright (C) 1998-2001  Gerard Roudier <groudier@free.fr>
 **
 **  This program is free software; you can redistribute it and/or modify
 **  it under the terms of the GNU General Public License as published by
@@ -36,15 +37,1275 @@
 **  And has been ported to NetBSD by
 **          Charles M. Hannum           <mycroft@gnu.ai.mit.edu>
 **
+**  NVRAM detection and reading.
+**    Copyright (C) 1997 Richard Waltham <dormouse@farsrobt.demon.co.uk>
+**
+**  Added support for MIPS big endian systems.
+**    Carsten Langgaard, carstenl@mips.com
+**    Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
+**
+**  Added support for HP PARISC big endian systems.
+**    Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
+**
 *******************************************************************************
 */
 
 #ifndef NCR53C8XX_H
 #define NCR53C8XX_H
 
+#include <linux/config.h>
 #include <scsi/scsi_host.h>
 
-#include "sym53c8xx_defs.h"
+/*
+**	If you want a driver as small as possible, do not define the 
+**	following options.
+*/
+#define SCSI_NCR_BOOT_COMMAND_LINE_SUPPORT
+#define SCSI_NCR_DEBUG_INFO_SUPPORT
+
+/*
+**	To disable integrity checking, do not define the 
+**	following option.
+*/
+#ifdef	CONFIG_SCSI_NCR53C8XX_INTEGRITY_CHECK
+#	define SCSI_NCR_ENABLE_INTEGRITY_CHECK
+#endif
+
+/* ---------------------------------------------------------------------
+** Take into account kernel configured parameters.
+** Most of these options can be overridden at startup by a command line.
+** ---------------------------------------------------------------------
+*/
+
+/*
+ * For Ultra2 and Ultra3 SCSI support option, use special features. 
+ *
+ * Value (default) means:
+ *	bit 0 : all features enabled, except:
+ *		bit 1 : PCI Write And Invalidate.
+ *		bit 2 : Data Phase Mismatch handling from SCRIPTS.
+ *
+ * Use boot options ncr53c8xx=specf:1 if you want all chip features to be 
+ * enabled by the driver.
+ */
+#define	SCSI_NCR_SETUP_SPECIAL_FEATURES		(3)
+
+#define SCSI_NCR_MAX_SYNC			(80)
+
+/*
+ * Allow tags from 2 to 256, default 8
+ */
+#ifdef	CONFIG_SCSI_NCR53C8XX_MAX_TAGS
+#if	CONFIG_SCSI_NCR53C8XX_MAX_TAGS < 2
+#define SCSI_NCR_MAX_TAGS	(2)
+#elif	CONFIG_SCSI_NCR53C8XX_MAX_TAGS > 256
+#define SCSI_NCR_MAX_TAGS	(256)
+#else
+#define	SCSI_NCR_MAX_TAGS	CONFIG_SCSI_NCR53C8XX_MAX_TAGS
+#endif
+#else
+#define SCSI_NCR_MAX_TAGS	(8)
+#endif
+
+/*
+ * Allow tagged command queuing support if configured with default number 
+ * of tags set to max (see above).
+ */
+#ifdef	CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS
+#define	SCSI_NCR_SETUP_DEFAULT_TAGS	CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS
+#elif	defined CONFIG_SCSI_NCR53C8XX_TAGGED_QUEUE
+#define	SCSI_NCR_SETUP_DEFAULT_TAGS	SCSI_NCR_MAX_TAGS
+#else
+#define	SCSI_NCR_SETUP_DEFAULT_TAGS	(0)
+#endif
+
+/*
+ * Immediate arbitration
+ */
+#if defined(CONFIG_SCSI_NCR53C8XX_IARB)
+#define SCSI_NCR_IARB_SUPPORT
+#endif
+
+/*
+ * Sync transfer frequency at startup.
+ * Allow from 5Mhz to 80Mhz default 20 Mhz.
+ */
+#ifndef	CONFIG_SCSI_NCR53C8XX_SYNC
+#define	CONFIG_SCSI_NCR53C8XX_SYNC	(20)
+#elif	CONFIG_SCSI_NCR53C8XX_SYNC > SCSI_NCR_MAX_SYNC
+#undef	CONFIG_SCSI_NCR53C8XX_SYNC
+#define	CONFIG_SCSI_NCR53C8XX_SYNC	SCSI_NCR_MAX_SYNC
+#endif
+
+#if	CONFIG_SCSI_NCR53C8XX_SYNC == 0
+#define	SCSI_NCR_SETUP_DEFAULT_SYNC	(255)
+#elif	CONFIG_SCSI_NCR53C8XX_SYNC <= 5
+#define	SCSI_NCR_SETUP_DEFAULT_SYNC	(50)
+#elif	CONFIG_SCSI_NCR53C8XX_SYNC <= 20
+#define	SCSI_NCR_SETUP_DEFAULT_SYNC	(250/(CONFIG_SCSI_NCR53C8XX_SYNC))
+#elif	CONFIG_SCSI_NCR53C8XX_SYNC <= 33
+#define	SCSI_NCR_SETUP_DEFAULT_SYNC	(11)
+#elif	CONFIG_SCSI_NCR53C8XX_SYNC <= 40
+#define	SCSI_NCR_SETUP_DEFAULT_SYNC	(10)
+#else
+#define	SCSI_NCR_SETUP_DEFAULT_SYNC 	(9)
+#endif
+
+/*
+ * Disallow disconnections at boot-up
+ */
+#ifdef CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT
+#define SCSI_NCR_SETUP_DISCONNECTION	(0)
+#else
+#define SCSI_NCR_SETUP_DISCONNECTION	(1)
+#endif
+
+/*
+ * Force synchronous negotiation for all targets
+ */
+#ifdef CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO
+#define SCSI_NCR_SETUP_FORCE_SYNC_NEGO	(1)
+#else
+#define SCSI_NCR_SETUP_FORCE_SYNC_NEGO	(0)
+#endif
+
+/*
+ * Disable master parity checking (flawed hardwares need that)
+ */
+#ifdef CONFIG_SCSI_NCR53C8XX_DISABLE_MPARITY_CHECK
+#define SCSI_NCR_SETUP_MASTER_PARITY	(0)
+#else
+#define SCSI_NCR_SETUP_MASTER_PARITY	(1)
+#endif
+
+/*
+ * Disable scsi parity checking (flawed devices may need that)
+ */
+#ifdef CONFIG_SCSI_NCR53C8XX_DISABLE_PARITY_CHECK
+#define SCSI_NCR_SETUP_SCSI_PARITY	(0)
+#else
+#define SCSI_NCR_SETUP_SCSI_PARITY	(1)
+#endif
+
+/*
+ * Settle time after reset at boot-up
+ */
+#define SCSI_NCR_SETUP_SETTLE_TIME	(2)
+
+/*
+**	Bridge quirks work-around option defaulted to 1.
+*/
+#ifndef	SCSI_NCR_PCIQ_WORK_AROUND_OPT
+#define	SCSI_NCR_PCIQ_WORK_AROUND_OPT	1
+#endif
+
+/*
+**	Work-around common bridge misbehaviour.
+**
+**	- Do not flush posted writes in the opposite 
+**	  direction on read.
+**	- May reorder DMA writes to memory.
+**
+**	This option should not affect performances 
+**	significantly, so it is the default.
+*/
+#if	SCSI_NCR_PCIQ_WORK_AROUND_OPT == 1
+#define	SCSI_NCR_PCIQ_MAY_NOT_FLUSH_PW_UPSTREAM
+#define	SCSI_NCR_PCIQ_MAY_REORDER_WRITES
+#define	SCSI_NCR_PCIQ_MAY_MISS_COMPLETIONS
+
+/*
+**	Same as option 1, but also deal with 
+**	misconfigured interrupts.
+**
+**	- Edge triggerred instead of level sensitive.
+**	- No interrupt line connected.
+**	- IRQ number misconfigured.
+**	
+**	If no interrupt is delivered, the driver will 
+**	catch the interrupt conditions 10 times per 
+**	second. No need to say that this option is 
+**	not recommended.
+*/
+#elif	SCSI_NCR_PCIQ_WORK_AROUND_OPT == 2
+#define	SCSI_NCR_PCIQ_MAY_NOT_FLUSH_PW_UPSTREAM
+#define	SCSI_NCR_PCIQ_MAY_REORDER_WRITES
+#define	SCSI_NCR_PCIQ_MAY_MISS_COMPLETIONS
+#define	SCSI_NCR_PCIQ_BROKEN_INTR
+
+/*
+**	Some bridge designers decided to flush 
+**	everything prior to deliver the interrupt.
+**	This option tries to deal with such a 
+**	behaviour.
+*/
+#elif	SCSI_NCR_PCIQ_WORK_AROUND_OPT == 3
+#define	SCSI_NCR_PCIQ_SYNC_ON_INTR
+#endif
+
+/*
+**	Other parameters not configurable with "make config"
+**	Avoid to change these constants, unless you know what you are doing.
+*/
+
+#define SCSI_NCR_ALWAYS_SIMPLE_TAG
+#define SCSI_NCR_MAX_SCATTER	(127)
+#define SCSI_NCR_MAX_TARGET	(16)
+
+/*
+**   Compute some desirable value for CAN_QUEUE 
+**   and CMD_PER_LUN.
+**   The driver will use lower values if these 
+**   ones appear to be too large.
+*/
+#define SCSI_NCR_CAN_QUEUE	(8*SCSI_NCR_MAX_TAGS + 2*SCSI_NCR_MAX_TARGET)
+#define SCSI_NCR_CMD_PER_LUN	(SCSI_NCR_MAX_TAGS)
+
+#define SCSI_NCR_SG_TABLESIZE	(SCSI_NCR_MAX_SCATTER)
+#define SCSI_NCR_TIMER_INTERVAL	(HZ)
+
+#if 1 /* defined CONFIG_SCSI_MULTI_LUN */
+#define SCSI_NCR_MAX_LUN	(16)
+#else
+#define SCSI_NCR_MAX_LUN	(1)
+#endif
+
+/*
+ *  IO functions definition for big/little endian CPU support.
+ *  For now, the NCR is only supported in little endian addressing mode, 
+ */
+
+#ifdef	__BIG_ENDIAN
+
+#define	inw_l2b		inw
+#define	inl_l2b		inl
+#define	outw_b2l	outw
+#define	outl_b2l	outl
+
+#define	readb_raw	readb
+#define	writeb_raw	writeb
+
+#if defined(SCSI_NCR_BIG_ENDIAN)
+#define	readw_l2b	__raw_readw
+#define	readl_l2b	__raw_readl
+#define	writew_b2l	__raw_writew
+#define	writel_b2l	__raw_writel
+#define	readw_raw	__raw_readw
+#define	readl_raw	__raw_readl
+#define	writew_raw	__raw_writew
+#define	writel_raw	__raw_writel
+#else	/* Other big-endian */
+#define	readw_l2b	readw
+#define	readl_l2b	readl
+#define	writew_b2l	writew
+#define	writel_b2l	writel
+#define	readw_raw	readw
+#define	readl_raw	readl
+#define	writew_raw	writew
+#define	writel_raw	writel
+#endif
+
+#else	/* little endian */
+
+#define	inw_raw		inw
+#define	inl_raw		inl
+#define	outw_raw	outw
+#define	outl_raw	outl
+
+#define	readb_raw	readb
+#define	readw_raw	readw
+#define	readl_raw	readl
+#define	writeb_raw	writeb
+#define	writew_raw	writew
+#define	writel_raw	writel
+
+#endif
+
+#if !defined(__hppa__) && !defined(__mips__)
+#ifdef	SCSI_NCR_BIG_ENDIAN
+#error	"The NCR in BIG ENDIAN addressing mode is not (yet) supported"
+#endif
+#endif
+
+#define MEMORY_BARRIER()	mb()
+
+
+/*
+ *  If the NCR uses big endian addressing mode over the 
+ *  PCI, actual io register addresses for byte and word 
+ *  accesses must be changed according to lane routing.
+ *  Btw, ncr_offb() and ncr_offw() macros only apply to 
+ *  constants and so donnot generate bloated code.
+ */
+
+#if	defined(SCSI_NCR_BIG_ENDIAN)
+
+#define ncr_offb(o)	(((o)&~3)+((~((o)&3))&3))
+#define ncr_offw(o)	(((o)&~3)+((~((o)&3))&2))
+
+#else
+
+#define ncr_offb(o)	(o)
+#define ncr_offw(o)	(o)
+
+#endif
+
+/*
+ *  If the CPU and the NCR use same endian-ness addressing,
+ *  no byte reordering is needed for script patching.
+ *  Macro cpu_to_scr() is to be used for script patching.
+ *  Macro scr_to_cpu() is to be used for getting a DWORD 
+ *  from the script.
+ */
+
+#if	defined(__BIG_ENDIAN) && !defined(SCSI_NCR_BIG_ENDIAN)
+
+#define cpu_to_scr(dw)	cpu_to_le32(dw)
+#define scr_to_cpu(dw)	le32_to_cpu(dw)
+
+#elif	defined(__LITTLE_ENDIAN) && defined(SCSI_NCR_BIG_ENDIAN)
+
+#define cpu_to_scr(dw)	cpu_to_be32(dw)
+#define scr_to_cpu(dw)	be32_to_cpu(dw)
+
+#else
+
+#define cpu_to_scr(dw)	(dw)
+#define scr_to_cpu(dw)	(dw)
+
+#endif
+
+/*
+ *  Access to the controller chip.
+ *
+ *  If the CPU and the NCR use same endian-ness addressing,
+ *  no byte reordering is needed for accessing chip io 
+ *  registers. Functions suffixed by '_raw' are assumed 
+ *  to access the chip over the PCI without doing byte 
+ *  reordering. Functions suffixed by '_l2b' are 
+ *  assumed to perform little-endian to big-endian byte 
+ *  reordering, those suffixed by '_b2l' blah, blah,
+ *  blah, ...
+ */
+
+/*
+ *  MEMORY mapped IO input / output
+ */
+
+#define INB_OFF(o)		readb_raw((char __iomem *)np->reg + ncr_offb(o))
+#define OUTB_OFF(o, val)	writeb_raw((val), (char __iomem *)np->reg + ncr_offb(o))
+
+#if	defined(__BIG_ENDIAN) && !defined(SCSI_NCR_BIG_ENDIAN)
+
+#define INW_OFF(o)		readw_l2b((char __iomem *)np->reg + ncr_offw(o))
+#define INL_OFF(o)		readl_l2b((char __iomem *)np->reg + (o))
+
+#define OUTW_OFF(o, val)	writew_b2l((val), (char __iomem *)np->reg + ncr_offw(o))
+#define OUTL_OFF(o, val)	writel_b2l((val), (char __iomem *)np->reg + (o))
+
+#elif	defined(__LITTLE_ENDIAN) && defined(SCSI_NCR_BIG_ENDIAN)
+
+#define INW_OFF(o)		readw_b2l((char __iomem *)np->reg + ncr_offw(o))
+#define INL_OFF(o)		readl_b2l((char __iomem *)np->reg + (o))
+
+#define OUTW_OFF(o, val)	writew_l2b((val), (char __iomem *)np->reg + ncr_offw(o))
+#define OUTL_OFF(o, val)	writel_l2b((val), (char __iomem *)np->reg + (o))
+
+#else
+
+#ifdef CONFIG_SCSI_NCR53C8XX_NO_WORD_TRANSFERS
+/* Only 8 or 32 bit transfers allowed */
+#define INW_OFF(o)		(readb((char __iomem *)np->reg + ncr_offw(o)) << 8 | readb((char __iomem *)np->reg + ncr_offw(o) + 1))
+#else
+#define INW_OFF(o)		readw_raw((char __iomem *)np->reg + ncr_offw(o))
+#endif
+#define INL_OFF(o)		readl_raw((char __iomem *)np->reg + (o))
+
+#ifdef CONFIG_SCSI_NCR53C8XX_NO_WORD_TRANSFERS
+/* Only 8 or 32 bit transfers allowed */
+#define OUTW_OFF(o, val)	do { writeb((char)((val) >> 8), (char __iomem *)np->reg + ncr_offw(o)); writeb((char)(val), (char __iomem *)np->reg + ncr_offw(o) + 1); } while (0)
+#else
+#define OUTW_OFF(o, val)	writew_raw((val), (char __iomem *)np->reg + ncr_offw(o))
+#endif
+#define OUTL_OFF(o, val)	writel_raw((val), (char __iomem *)np->reg + (o))
+
+#endif
+
+#define INB(r)		INB_OFF (offsetof(struct ncr_reg,r))
+#define INW(r)		INW_OFF (offsetof(struct ncr_reg,r))
+#define INL(r)		INL_OFF (offsetof(struct ncr_reg,r))
+
+#define OUTB(r, val)	OUTB_OFF (offsetof(struct ncr_reg,r), (val))
+#define OUTW(r, val)	OUTW_OFF (offsetof(struct ncr_reg,r), (val))
+#define OUTL(r, val)	OUTL_OFF (offsetof(struct ncr_reg,r), (val))
+
+/*
+ *  Set bit field ON, OFF 
+ */
+
+#define OUTONB(r, m)	OUTB(r, INB(r) | (m))
+#define OUTOFFB(r, m)	OUTB(r, INB(r) & ~(m))
+#define OUTONW(r, m)	OUTW(r, INW(r) | (m))
+#define OUTOFFW(r, m)	OUTW(r, INW(r) & ~(m))
+#define OUTONL(r, m)	OUTL(r, INL(r) | (m))
+#define OUTOFFL(r, m)	OUTL(r, INL(r) & ~(m))
+
+/*
+ *  We normally want the chip to have a consistent view
+ *  of driver internal data structures when we restart it.
+ *  Thus these macros.
+ */
+#define OUTL_DSP(v)				\
+	do {					\
+		MEMORY_BARRIER();		\
+		OUTL (nc_dsp, (v));		\
+	} while (0)
+
+#define OUTONB_STD()				\
+	do {					\
+		MEMORY_BARRIER();		\
+		OUTONB (nc_dcntl, (STD|NOCOM));	\
+	} while (0)
+
+
+/*
+**   NCR53C8XX devices features table.
+*/
+struct ncr_chip {
+	unsigned short	revision_id;
+	unsigned char	burst_max;	/* log-base-2 of max burst */
+	unsigned char	offset_max;
+	unsigned char	nr_divisor;
+	unsigned int	features;
+#define FE_LED0		(1<<0)
+#define FE_WIDE		(1<<1)    /* Wide data transfers */
+#define FE_ULTRA	(1<<2)	  /* Ultra speed 20Mtrans/sec */
+#define FE_DBLR		(1<<4)	  /* Clock doubler present */
+#define FE_QUAD		(1<<5)	  /* Clock quadrupler present */
+#define FE_ERL		(1<<6)    /* Enable read line */
+#define FE_CLSE		(1<<7)    /* Cache line size enable */
+#define FE_WRIE		(1<<8)    /* Write & Invalidate enable */
+#define FE_ERMP		(1<<9)    /* Enable read multiple */
+#define FE_BOF		(1<<10)   /* Burst opcode fetch */
+#define FE_DFS		(1<<11)   /* DMA fifo size */
+#define FE_PFEN		(1<<12)   /* Prefetch enable */
+#define FE_LDSTR	(1<<13)   /* Load/Store supported */
+#define FE_RAM		(1<<14)   /* On chip RAM present */
+#define FE_VARCLK	(1<<15)   /* SCSI clock may vary */
+#define FE_RAM8K	(1<<16)   /* On chip RAM sized 8Kb */
+#define FE_64BIT	(1<<17)   /* Have a 64-bit PCI interface */
+#define FE_IO256	(1<<18)   /* Requires full 256 bytes in PCI space */
+#define FE_NOPM		(1<<19)   /* Scripts handles phase mismatch */
+#define FE_LEDC		(1<<20)   /* Hardware control of LED */
+#define FE_DIFF		(1<<21)   /* Support Differential SCSI */
+#define FE_66MHZ 	(1<<23)   /* 66MHz PCI Support */
+#define FE_DAC	 	(1<<24)   /* Support DAC cycles (64 bit addressing) */
+#define FE_ISTAT1 	(1<<25)   /* Have ISTAT1, MBOX0, MBOX1 registers */
+#define FE_DAC_IN_USE	(1<<26)	  /* Platform does DAC cycles */
+#define FE_EHP		(1<<27)   /* 720: Even host parity */
+#define FE_MUX		(1<<28)   /* 720: Multiplexed bus */
+#define FE_EA		(1<<29)   /* 720: Enable Ack */
+
+#define FE_CACHE_SET	(FE_ERL|FE_CLSE|FE_WRIE|FE_ERMP)
+#define FE_SCSI_SET	(FE_WIDE|FE_ULTRA|FE_DBLR|FE_QUAD|F_CLK80)
+#define FE_SPECIAL_SET	(FE_CACHE_SET|FE_BOF|FE_DFS|FE_LDSTR|FE_PFEN|FE_RAM)
+};
+
+
+/*
+**	Driver setup structure.
+**
+**	This structure is initialized from linux config options.
+**	It can be overridden at boot-up by the boot command line.
+*/
+#define SCSI_NCR_MAX_EXCLUDES 8
+struct ncr_driver_setup {
+	u8	master_parity;
+	u8	scsi_parity;
+	u8	disconnection;
+	u8	special_features;
+	u8	force_sync_nego;
+	u8	reverse_probe;
+	u8	pci_fix_up;
+	u8	use_nvram;
+	u8	verbose;
+	u8	default_tags;
+	u16	default_sync;
+	u16	debug;
+	u8	burst_max;
+	u8	led_pin;
+	u8	max_wide;
+	u8	settle_delay;
+	u8	diff_support;
+	u8	irqm;
+	u8	bus_check;
+	u8	optimize;
+	u8	recovery;
+	u8	host_id;
+	u16	iarb;
+	u32	excludes[SCSI_NCR_MAX_EXCLUDES];
+	char	tag_ctrl[100];
+};
+
+/*
+**	Initial setup.
+**	Can be overriden at startup by a command line.
+*/
+#define SCSI_NCR_DRIVER_SETUP			\
+{						\
+	SCSI_NCR_SETUP_MASTER_PARITY,		\
+	SCSI_NCR_SETUP_SCSI_PARITY,		\
+	SCSI_NCR_SETUP_DISCONNECTION,		\
+	SCSI_NCR_SETUP_SPECIAL_FEATURES,	\
+	SCSI_NCR_SETUP_FORCE_SYNC_NEGO,		\
+	0,					\
+	0,					\
+	1,					\
+	0,					\
+	SCSI_NCR_SETUP_DEFAULT_TAGS,		\
+	SCSI_NCR_SETUP_DEFAULT_SYNC,		\
+	0x00,					\
+	7,					\
+	0,					\
+	1,					\
+	SCSI_NCR_SETUP_SETTLE_TIME,		\
+	0,					\
+	0,					\
+	1,					\
+	0,					\
+	0,					\
+	255,					\
+	0x00					\
+}
+
+/*
+**	Boot fail safe setup.
+**	Override initial setup from boot command line:
+**	ncr53c8xx=safe:y
+*/
+#define SCSI_NCR_DRIVER_SAFE_SETUP		\
+{						\
+	0,					\
+	1,					\
+	0,					\
+	0,					\
+	0,					\
+	0,					\
+	0,					\
+	1,					\
+	2,					\
+	0,					\
+	255,					\
+	0x00,					\
+	255,					\
+	0,					\
+	0,					\
+	10,					\
+	1,					\
+	1,					\
+	1,					\
+	0,					\
+	0,					\
+	255					\
+}
+
+/**************** ORIGINAL CONTENT of ncrreg.h from FreeBSD ******************/
+
+/*-----------------------------------------------------------------
+**
+**	The ncr 53c810 register structure.
+**
+**-----------------------------------------------------------------
+*/
+
+struct ncr_reg {
+/*00*/  u8	nc_scntl0;    /* full arb., ena parity, par->ATN  */
+
+/*01*/  u8	nc_scntl1;    /* no reset                         */
+        #define   ISCON   0x10  /* connected to scsi		    */
+        #define   CRST    0x08  /* force reset                      */
+        #define   IARB    0x02  /* immediate arbitration            */
+
+/*02*/  u8	nc_scntl2;    /* no disconnect expected           */
+	#define   SDU     0x80  /* cmd: disconnect will raise error */
+	#define   CHM     0x40  /* sta: chained mode                */
+	#define   WSS     0x08  /* sta: wide scsi send           [W]*/
+	#define   WSR     0x01  /* sta: wide scsi received       [W]*/
+
+/*03*/  u8	nc_scntl3;    /* cnf system clock dependent       */
+	#define   EWS     0x08  /* cmd: enable wide scsi         [W]*/
+	#define   ULTRA   0x80  /* cmd: ULTRA enable                */
+				/* bits 0-2, 7 rsvd for C1010       */
+
+/*04*/  u8	nc_scid;	/* cnf host adapter scsi address    */
+	#define   RRE     0x40  /* r/w:e enable response to resel.  */
+	#define   SRE     0x20  /* r/w:e enable response to select  */
+
+/*05*/  u8	nc_sxfer;	/* ### Sync speed and count         */
+				/* bits 6-7 rsvd for C1010          */
+
+/*06*/  u8	nc_sdid;	/* ### Destination-ID               */
+
+/*07*/  u8	nc_gpreg;	/* ??? IO-Pins                      */
+
+/*08*/  u8	nc_sfbr;	/* ### First byte in phase          */
+
+/*09*/  u8	nc_socl;
+	#define   CREQ	  0x80	/* r/w: SCSI-REQ                    */
+	#define   CACK	  0x40	/* r/w: SCSI-ACK                    */
+	#define   CBSY	  0x20	/* r/w: SCSI-BSY                    */
+	#define   CSEL	  0x10	/* r/w: SCSI-SEL                    */
+	#define   CATN	  0x08	/* r/w: SCSI-ATN                    */
+	#define   CMSG	  0x04	/* r/w: SCSI-MSG                    */
+	#define   CC_D	  0x02	/* r/w: SCSI-C_D                    */
+	#define   CI_O	  0x01	/* r/w: SCSI-I_O                    */
+
+/*0a*/  u8	nc_ssid;
+
+/*0b*/  u8	nc_sbcl;
+
+/*0c*/  u8	nc_dstat;
+        #define   DFE     0x80  /* sta: dma fifo empty              */
+        #define   MDPE    0x40  /* int: master data parity error    */
+        #define   BF      0x20  /* int: script: bus fault           */
+        #define   ABRT    0x10  /* int: script: command aborted     */
+        #define   SSI     0x08  /* int: script: single step         */
+        #define   SIR     0x04  /* int: script: interrupt instruct. */
+        #define   IID     0x01  /* int: script: illegal instruct.   */
+
+/*0d*/  u8	nc_sstat0;
+        #define   ILF     0x80  /* sta: data in SIDL register lsb   */
+        #define   ORF     0x40  /* sta: data in SODR register lsb   */
+        #define   OLF     0x20  /* sta: data in SODL register lsb   */
+        #define   AIP     0x10  /* sta: arbitration in progress     */
+        #define   LOA     0x08  /* sta: arbitration lost            */
+        #define   WOA     0x04  /* sta: arbitration won             */
+        #define   IRST    0x02  /* sta: scsi reset signal           */
+        #define   SDP     0x01  /* sta: scsi parity signal          */
+
+/*0e*/  u8	nc_sstat1;
+	#define   FF3210  0xf0	/* sta: bytes in the scsi fifo      */
+
+/*0f*/  u8	nc_sstat2;
+        #define   ILF1    0x80  /* sta: data in SIDL register msb[W]*/
+        #define   ORF1    0x40  /* sta: data in SODR register msb[W]*/
+        #define   OLF1    0x20  /* sta: data in SODL register msb[W]*/
+        #define   DM      0x04  /* sta: DIFFSENS mismatch (895/6 only) */
+        #define   LDSC    0x02  /* sta: disconnect & reconnect      */
+
+/*10*/  u8	nc_dsa;	/* --> Base page                    */
+/*11*/  u8	nc_dsa1;
+/*12*/  u8	nc_dsa2;
+/*13*/  u8	nc_dsa3;
+
+/*14*/  u8	nc_istat;	/* --> Main Command and status      */
+        #define   CABRT   0x80  /* cmd: abort current operation     */
+        #define   SRST    0x40  /* mod: reset chip                  */
+        #define   SIGP    0x20  /* r/w: message from host to ncr    */
+        #define   SEM     0x10  /* r/w: message between host + ncr  */
+        #define   CON     0x08  /* sta: connected to scsi           */
+        #define   INTF    0x04  /* sta: int on the fly (reset by wr)*/
+        #define   SIP     0x02  /* sta: scsi-interrupt              */
+        #define   DIP     0x01  /* sta: host/script interrupt       */
+
+/*15*/  u8	nc_istat1;	/* 896 and later cores only */
+        #define   FLSH    0x04  /* sta: chip is flushing            */
+        #define   SRUN    0x02  /* sta: scripts are running         */
+        #define   SIRQD   0x01  /* r/w: disable INT pin             */
+
+/*16*/  u8	nc_mbox0;	/* 896 and later cores only */
+/*17*/  u8	nc_mbox1;	/* 896 and later cores only */
+
+/*18*/	u8	nc_ctest0;
+	#define   EHP     0x04	/* 720 even host parity             */
+/*19*/  u8	nc_ctest1;
+
+/*1a*/  u8	nc_ctest2;
+	#define   CSIGP   0x40
+				/* bits 0-2,7 rsvd for C1010        */
+
+/*1b*/  u8	nc_ctest3;
+	#define   FLF     0x08  /* cmd: flush dma fifo              */
+	#define   CLF	  0x04	/* cmd: clear dma fifo		    */
+	#define   FM      0x02  /* mod: fetch pin mode              */
+	#define   WRIE    0x01  /* mod: write and invalidate enable */
+				/* bits 4-7 rsvd for C1010          */
+
+/*1c*/  u32    nc_temp;	/* ### Temporary stack              */
+
+/*20*/	u8	nc_dfifo;
+/*21*/  u8	nc_ctest4;
+	#define   MUX     0x80  /* 720 host bus multiplex mode      */
+	#define   BDIS    0x80  /* mod: burst disable               */
+	#define   MPEE    0x08  /* mod: master parity error enable  */
+
+/*22*/  u8	nc_ctest5;
+	#define   DFS     0x20  /* mod: dma fifo size               */
+				/* bits 0-1, 3-7 rsvd for C1010          */
+/*23*/  u8	nc_ctest6;
+
+/*24*/  u32    nc_dbc;	/* ### Byte count and command       */
+/*28*/  u32    nc_dnad;	/* ### Next command register        */
+/*2c*/  u32    nc_dsp;	/* --> Script Pointer               */
+/*30*/  u32    nc_dsps;	/* --> Script pointer save/opcode#2 */
+
+/*34*/  u8	nc_scratcha;  /* Temporary register a            */
+/*35*/  u8	nc_scratcha1;
+/*36*/  u8	nc_scratcha2;
+/*37*/  u8	nc_scratcha3;
+
+/*38*/  u8	nc_dmode;
+	#define   BL_2    0x80  /* mod: burst length shift value +2 */
+	#define   BL_1    0x40  /* mod: burst length shift value +1 */
+	#define   ERL     0x08  /* mod: enable read line            */
+	#define   ERMP    0x04  /* mod: enable read multiple        */
+	#define   BOF     0x02  /* mod: burst op code fetch         */
+
+/*39*/  u8	nc_dien;
+/*3a*/  u8	nc_sbr;
+
+/*3b*/  u8	nc_dcntl;	/* --> Script execution control     */
+	#define   CLSE    0x80  /* mod: cache line size enable      */
+	#define   PFF     0x40  /* cmd: pre-fetch flush             */
+	#define   PFEN    0x20  /* mod: pre-fetch enable            */
+	#define   EA      0x20  /* mod: 720 enable-ack              */
+	#define   SSM     0x10  /* mod: single step mode            */
+	#define   IRQM    0x08  /* mod: irq mode (1 = totem pole !) */
+	#define   STD     0x04  /* cmd: start dma mode              */
+	#define   IRQD    0x02  /* mod: irq disable                 */
+ 	#define	  NOCOM   0x01	/* cmd: protect sfbr while reselect */
+				/* bits 0-1 rsvd for C1010          */
+
+/*3c*/  u32	nc_adder;
+
+/*40*/  u16	nc_sien;	/* -->: interrupt enable            */
+/*42*/  u16	nc_sist;	/* <--: interrupt status            */
+        #define   SBMC    0x1000/* sta: SCSI Bus Mode Change (895/6 only) */
+        #define   STO     0x0400/* sta: timeout (select)            */
+        #define   GEN     0x0200/* sta: timeout (general)           */
+        #define   HTH     0x0100/* sta: timeout (handshake)         */
+        #define   MA      0x80  /* sta: phase mismatch              */
+        #define   CMP     0x40  /* sta: arbitration complete        */
+        #define   SEL     0x20  /* sta: selected by another device  */
+        #define   RSL     0x10  /* sta: reselected by another device*/
+        #define   SGE     0x08  /* sta: gross error (over/underflow)*/
+        #define   UDC     0x04  /* sta: unexpected disconnect       */
+        #define   RST     0x02  /* sta: scsi bus reset detected     */
+        #define   PAR     0x01  /* sta: scsi parity error           */
+
+/*44*/  u8	nc_slpar;
+/*45*/  u8	nc_swide;
+/*46*/  u8	nc_macntl;
+/*47*/  u8	nc_gpcntl;
+/*48*/  u8	nc_stime0;    /* cmd: timeout for select&handshake*/
+/*49*/  u8	nc_stime1;    /* cmd: timeout user defined        */
+/*4a*/  u16   nc_respid;    /* sta: Reselect-IDs                */
+
+/*4c*/  u8	nc_stest0;
+
+/*4d*/  u8	nc_stest1;
+	#define   SCLK    0x80	/* Use the PCI clock as SCSI clock	*/
+	#define   DBLEN   0x08	/* clock doubler running		*/
+	#define   DBLSEL  0x04	/* clock doubler selected		*/
+  
+
+/*4e*/  u8	nc_stest2;
+	#define   ROF     0x40	/* reset scsi offset (after gross error!) */
+	#define   DIF     0x20  /* 720 SCSI differential mode             */
+	#define   EXT     0x02  /* extended filtering                     */
+
+/*4f*/  u8	nc_stest3;
+	#define   TE     0x80	/* c: tolerAnt enable */
+	#define   HSC    0x20	/* c: Halt SCSI Clock */
+	#define   CSF    0x02	/* c: clear scsi fifo */
+
+/*50*/  u16   nc_sidl;	/* Lowlevel: latched from scsi data */
+/*52*/  u8	nc_stest4;
+	#define   SMODE  0xc0	/* SCSI bus mode      (895/6 only) */
+	#define    SMODE_HVD 0x40	/* High Voltage Differential       */
+	#define    SMODE_SE  0x80	/* Single Ended                    */
+	#define    SMODE_LVD 0xc0	/* Low Voltage Differential        */
+	#define   LCKFRQ 0x20	/* Frequency Lock (895/6 only)     */
+				/* bits 0-5 rsvd for C1010          */
+
+/*53*/  u8	nc_53_;
+/*54*/  u16	nc_sodl;	/* Lowlevel: data out to scsi data  */
+/*56*/	u8	nc_ccntl0;	/* Chip Control 0 (896)             */
+	#define   ENPMJ  0x80	/* Enable Phase Mismatch Jump       */
+	#define   PMJCTL 0x40	/* Phase Mismatch Jump Control      */
+	#define   ENNDJ  0x20	/* Enable Non Data PM Jump          */
+	#define   DISFC  0x10	/* Disable Auto FIFO Clear          */
+	#define   DILS   0x02	/* Disable Internal Load/Store      */
+	#define   DPR    0x01	/* Disable Pipe Req                 */
+
+/*57*/	u8	nc_ccntl1;	/* Chip Control 1 (896)             */
+	#define   ZMOD   0x80	/* High Impedance Mode              */
+	#define	  DIC	 0x10	/* Disable Internal Cycles	    */
+	#define   DDAC   0x08	/* Disable Dual Address Cycle       */
+	#define   XTIMOD 0x04	/* 64-bit Table Ind. Indexing Mode  */
+	#define   EXTIBMV 0x02	/* Enable 64-bit Table Ind. BMOV    */
+	#define   EXDBMV 0x01	/* Enable 64-bit Direct BMOV        */
+
+/*58*/  u16	nc_sbdl;	/* Lowlevel: data from scsi data    */
+/*5a*/  u16	nc_5a_;
+
+/*5c*/  u8	nc_scr0;	/* Working register B               */
+/*5d*/  u8	nc_scr1;	/*                                  */
+/*5e*/  u8	nc_scr2;	/*                                  */
+/*5f*/  u8	nc_scr3;	/*                                  */
+
+/*60*/  u8	nc_scrx[64];	/* Working register C-R             */
+/*a0*/	u32	nc_mmrs;	/* Memory Move Read Selector        */
+/*a4*/	u32	nc_mmws;	/* Memory Move Write Selector       */
+/*a8*/	u32	nc_sfs;		/* Script Fetch Selector            */
+/*ac*/	u32	nc_drs;		/* DSA Relative Selector            */
+/*b0*/	u32	nc_sbms;	/* Static Block Move Selector       */
+/*b4*/	u32	nc_dbms;	/* Dynamic Block Move Selector      */
+/*b8*/	u32	nc_dnad64;	/* DMA Next Address 64              */
+/*bc*/	u16	nc_scntl4;	/* C1010 only                       */
+	#define   U3EN   0x80	/* Enable Ultra 3                   */
+	#define   AIPEN	 0x40   /* Allow check upper byte lanes     */
+	#define   XCLKH_DT 0x08 /* Extra clock of data hold on DT
+					transfer edge	            */
+	#define   XCLKH_ST 0x04 /* Extra clock of data hold on ST
+					transfer edge	            */
+
+/*be*/  u8	nc_aipcntl0;	/* Epat Control 1 C1010 only        */
+/*bf*/  u8	nc_aipcntl1;	/* AIP Control C1010_66 Only        */
+
+/*c0*/	u32	nc_pmjad1;	/* Phase Mismatch Jump Address 1    */
+/*c4*/	u32	nc_pmjad2;	/* Phase Mismatch Jump Address 2    */
+/*c8*/	u8	nc_rbc;		/* Remaining Byte Count             */
+/*c9*/	u8	nc_rbc1;	/*                                  */
+/*ca*/	u8	nc_rbc2;	/*                                  */
+/*cb*/	u8	nc_rbc3;	/*                                  */
+
+/*cc*/	u8	nc_ua;		/* Updated Address                  */
+/*cd*/	u8	nc_ua1;		/*                                  */
+/*ce*/	u8	nc_ua2;		/*                                  */
+/*cf*/	u8	nc_ua3;		/*                                  */
+/*d0*/	u32	nc_esa;		/* Entry Storage Address            */
+/*d4*/	u8	nc_ia;		/* Instruction Address              */
+/*d5*/	u8	nc_ia1;
+/*d6*/	u8	nc_ia2;
+/*d7*/	u8	nc_ia3;
+/*d8*/	u32	nc_sbc;		/* SCSI Byte Count (3 bytes only)   */
+/*dc*/	u32	nc_csbc;	/* Cumulative SCSI Byte Count       */
+
+				/* Following for C1010 only         */
+/*e0*/  u16	nc_crcpad;	/* CRC Value                        */
+/*e2*/  u8	nc_crccntl0;	/* CRC control register             */
+	#define   SNDCRC  0x10	/* Send CRC Request                 */
+/*e3*/  u8	nc_crccntl1;	/* CRC control register             */
+/*e4*/  u32	nc_crcdata;	/* CRC data register                */ 
+/*e8*/  u32	nc_e8_;		/* rsvd 			    */
+/*ec*/  u32	nc_ec_;		/* rsvd 			    */
+/*f0*/  u16	nc_dfbc;	/* DMA FIFO byte count              */ 
+
+};
+
+/*-----------------------------------------------------------
+**
+**	Utility macros for the script.
+**
+**-----------------------------------------------------------
+*/
+
+#define REGJ(p,r) (offsetof(struct ncr_reg, p ## r))
+#define REG(r) REGJ (nc_, r)
+
+typedef u32 ncrcmd;
+
+/*-----------------------------------------------------------
+**
+**	SCSI phases
+**
+**	DT phases illegal for ncr driver.
+**
+**-----------------------------------------------------------
+*/
+
+#define	SCR_DATA_OUT	0x00000000
+#define	SCR_DATA_IN	0x01000000
+#define	SCR_COMMAND	0x02000000
+#define	SCR_STATUS	0x03000000
+#define SCR_DT_DATA_OUT	0x04000000
+#define SCR_DT_DATA_IN	0x05000000
+#define SCR_MSG_OUT	0x06000000
+#define SCR_MSG_IN      0x07000000
+
+#define SCR_ILG_OUT	0x04000000
+#define SCR_ILG_IN	0x05000000
+
+/*-----------------------------------------------------------
+**
+**	Data transfer via SCSI.
+**
+**-----------------------------------------------------------
+**
+**	MOVE_ABS (LEN)
+**	<<start address>>
+**
+**	MOVE_IND (LEN)
+**	<<dnad_offset>>
+**
+**	MOVE_TBL
+**	<<dnad_offset>>
+**
+**-----------------------------------------------------------
+*/
+
+#define OPC_MOVE          0x08000000
+
+#define SCR_MOVE_ABS(l) ((0x00000000 | OPC_MOVE) | (l))
+#define SCR_MOVE_IND(l) ((0x20000000 | OPC_MOVE) | (l))
+#define SCR_MOVE_TBL     (0x10000000 | OPC_MOVE)
+
+#define SCR_CHMOV_ABS(l) ((0x00000000) | (l))
+#define SCR_CHMOV_IND(l) ((0x20000000) | (l))
+#define SCR_CHMOV_TBL     (0x10000000)
+
+struct scr_tblmove {
+        u32  size;
+        u32  addr;
+};
+
+/*-----------------------------------------------------------
+**
+**	Selection
+**
+**-----------------------------------------------------------
+**
+**	SEL_ABS | SCR_ID (0..15)    [ | REL_JMP]
+**	<<alternate_address>>
+**
+**	SEL_TBL | << dnad_offset>>  [ | REL_JMP]
+**	<<alternate_address>>
+**
+**-----------------------------------------------------------
+*/
+
+#define	SCR_SEL_ABS	0x40000000
+#define	SCR_SEL_ABS_ATN	0x41000000
+#define	SCR_SEL_TBL	0x42000000
+#define	SCR_SEL_TBL_ATN	0x43000000
+
+
+#ifdef SCSI_NCR_BIG_ENDIAN
+struct scr_tblsel {
+        u8	sel_scntl3;
+        u8	sel_id;
+        u8	sel_sxfer;
+        u8	sel_scntl4;	
+};
+#else
+struct scr_tblsel {
+        u8	sel_scntl4;	
+        u8	sel_sxfer;
+        u8	sel_id;
+        u8	sel_scntl3;
+};
+#endif
+
+#define SCR_JMP_REL     0x04000000
+#define SCR_ID(id)	(((u32)(id)) << 16)
+
+/*-----------------------------------------------------------
+**
+**	Waiting for Disconnect or Reselect
+**
+**-----------------------------------------------------------
+**
+**	WAIT_DISC
+**	dummy: <<alternate_address>>
+**
+**	WAIT_RESEL
+**	<<alternate_address>>
+**
+**-----------------------------------------------------------
+*/
+
+#define	SCR_WAIT_DISC	0x48000000
+#define SCR_WAIT_RESEL  0x50000000
+
+/*-----------------------------------------------------------
+**
+**	Bit Set / Reset
+**
+**-----------------------------------------------------------
+**
+**	SET (flags {|.. })
+**
+**	CLR (flags {|.. })
+**
+**-----------------------------------------------------------
+*/
+
+#define SCR_SET(f)     (0x58000000 | (f))
+#define SCR_CLR(f)     (0x60000000 | (f))
+
+#define	SCR_CARRY	0x00000400
+#define	SCR_TRG		0x00000200
+#define	SCR_ACK		0x00000040
+#define	SCR_ATN		0x00000008
+
+
+
+
+/*-----------------------------------------------------------
+**
+**	Memory to memory move
+**
+**-----------------------------------------------------------
+**
+**	COPY (bytecount)
+**	<< source_address >>
+**	<< destination_address >>
+**
+**	SCR_COPY   sets the NO FLUSH option by default.
+**	SCR_COPY_F does not set this option.
+**
+**	For chips which do not support this option,
+**	ncr_copy_and_bind() will remove this bit.
+**-----------------------------------------------------------
+*/
+
+#define SCR_NO_FLUSH 0x01000000
+
+#define SCR_COPY(n) (0xc0000000 | SCR_NO_FLUSH | (n))
+#define SCR_COPY_F(n) (0xc0000000 | (n))
+
+/*-----------------------------------------------------------
+**
+**	Register move and binary operations
+**
+**-----------------------------------------------------------
+**
+**	SFBR_REG (reg, op, data)        reg  = SFBR op data
+**	<< 0 >>
+**
+**	REG_SFBR (reg, op, data)        SFBR = reg op data
+**	<< 0 >>
+**
+**	REG_REG  (reg, op, data)        reg  = reg op data
+**	<< 0 >>
+**
+**-----------------------------------------------------------
+**	On 810A, 860, 825A, 875, 895 and 896 chips the content 
+**	of SFBR register can be used as data (SCR_SFBR_DATA).
+**	The 896 has additionnal IO registers starting at 
+**	offset 0x80. Bit 7 of register offset is stored in 
+**	bit 7 of the SCRIPTS instruction first DWORD.
+**-----------------------------------------------------------
+*/
+
+#define SCR_REG_OFS(ofs) ((((ofs) & 0x7f) << 16ul) + ((ofs) & 0x80)) 
+
+#define SCR_SFBR_REG(reg,op,data) \
+        (0x68000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
+
+#define SCR_REG_SFBR(reg,op,data) \
+        (0x70000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
+
+#define SCR_REG_REG(reg,op,data) \
+        (0x78000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
+
+
+#define      SCR_LOAD   0x00000000
+#define      SCR_SHL    0x01000000
+#define      SCR_OR     0x02000000
+#define      SCR_XOR    0x03000000
+#define      SCR_AND    0x04000000
+#define      SCR_SHR    0x05000000
+#define      SCR_ADD    0x06000000
+#define      SCR_ADDC   0x07000000
+
+#define      SCR_SFBR_DATA   (0x00800000>>8ul)	/* Use SFBR as data */
+
+/*-----------------------------------------------------------
+**
+**	FROM_REG (reg)		  SFBR = reg
+**	<< 0 >>
+**
+**	TO_REG	 (reg)		  reg  = SFBR
+**	<< 0 >>
+**
+**	LOAD_REG (reg, data)	  reg  = <data>
+**	<< 0 >>
+**
+**	LOAD_SFBR(data) 	  SFBR = <data>
+**	<< 0 >>
+**
+**-----------------------------------------------------------
+*/
+
+#define	SCR_FROM_REG(reg) \
+	SCR_REG_SFBR(reg,SCR_OR,0)
+
+#define	SCR_TO_REG(reg) \
+	SCR_SFBR_REG(reg,SCR_OR,0)
+
+#define	SCR_LOAD_REG(reg,data) \
+	SCR_REG_REG(reg,SCR_LOAD,data)
+
+#define SCR_LOAD_SFBR(data) \
+        (SCR_REG_SFBR (gpreg, SCR_LOAD, data))
+
+/*-----------------------------------------------------------
+**
+**	LOAD  from memory   to register.
+**	STORE from register to memory.
+**
+**	Only supported by 810A, 860, 825A, 875, 895 and 896.
+**
+**-----------------------------------------------------------
+**
+**	LOAD_ABS (LEN)
+**	<<start address>>
+**
+**	LOAD_REL (LEN)        (DSA relative)
+**	<<dsa_offset>>
+**
+**-----------------------------------------------------------
+*/
+
+#define SCR_REG_OFS2(ofs) (((ofs) & 0xff) << 16ul)
+#define SCR_NO_FLUSH2	0x02000000
+#define SCR_DSA_REL2	0x10000000
+
+#define SCR_LOAD_R(reg, how, n) \
+        (0xe1000000 | how | (SCR_REG_OFS2(REG(reg))) | (n))
+
+#define SCR_STORE_R(reg, how, n) \
+        (0xe0000000 | how | (SCR_REG_OFS2(REG(reg))) | (n))
+
+#define SCR_LOAD_ABS(reg, n)	SCR_LOAD_R(reg, SCR_NO_FLUSH2, n)
+#define SCR_LOAD_REL(reg, n)	SCR_LOAD_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2, n)
+#define SCR_LOAD_ABS_F(reg, n)	SCR_LOAD_R(reg, 0, n)
+#define SCR_LOAD_REL_F(reg, n)	SCR_LOAD_R(reg, SCR_DSA_REL2, n)
+
+#define SCR_STORE_ABS(reg, n)	SCR_STORE_R(reg, SCR_NO_FLUSH2, n)
+#define SCR_STORE_REL(reg, n)	SCR_STORE_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2,n)
+#define SCR_STORE_ABS_F(reg, n)	SCR_STORE_R(reg, 0, n)
+#define SCR_STORE_REL_F(reg, n)	SCR_STORE_R(reg, SCR_DSA_REL2, n)
+
+
+/*-----------------------------------------------------------
+**
+**	Waiting for Disconnect or Reselect
+**
+**-----------------------------------------------------------
+**
+**	JUMP            [ | IFTRUE/IFFALSE ( ... ) ]
+**	<<address>>
+**
+**	JUMPR           [ | IFTRUE/IFFALSE ( ... ) ]
+**	<<distance>>
+**
+**	CALL            [ | IFTRUE/IFFALSE ( ... ) ]
+**	<<address>>
+**
+**	CALLR           [ | IFTRUE/IFFALSE ( ... ) ]
+**	<<distance>>
+**
+**	RETURN          [ | IFTRUE/IFFALSE ( ... ) ]
+**	<<dummy>>
+**
+**	INT             [ | IFTRUE/IFFALSE ( ... ) ]
+**	<<ident>>
+**
+**	INT_FLY         [ | IFTRUE/IFFALSE ( ... ) ]
+**	<<ident>>
+**
+**	Conditions:
+**	     WHEN (phase)
+**	     IF   (phase)
+**	     CARRYSET
+**	     DATA (data, mask)
+**
+**-----------------------------------------------------------
+*/
+
+#define SCR_NO_OP       0x80000000
+#define SCR_JUMP        0x80080000
+#define SCR_JUMP64      0x80480000
+#define SCR_JUMPR       0x80880000
+#define SCR_CALL        0x88080000
+#define SCR_CALLR       0x88880000
+#define SCR_RETURN      0x90080000
+#define SCR_INT         0x98080000
+#define SCR_INT_FLY     0x98180000
+
+#define IFFALSE(arg)   (0x00080000 | (arg))
+#define IFTRUE(arg)    (0x00000000 | (arg))
+
+#define WHEN(phase)    (0x00030000 | (phase))
+#define IF(phase)      (0x00020000 | (phase))
+
+#define DATA(D)        (0x00040000 | ((D) & 0xff))
+#define MASK(D,M)      (0x00040000 | (((M ^ 0xff) & 0xff) << 8ul)|((D) & 0xff))
+
+#define CARRYSET       (0x00200000)
+
+/*-----------------------------------------------------------
+**
+**	SCSI  constants.
+**
+**-----------------------------------------------------------
+*/
+
+/*
+**	Messages
+*/
+
+#define	M_COMPLETE	COMMAND_COMPLETE
+#define	M_EXTENDED	EXTENDED_MESSAGE
+#define	M_SAVE_DP	SAVE_POINTERS
+#define	M_RESTORE_DP	RESTORE_POINTERS
+#define	M_DISCONNECT	DISCONNECT
+#define	M_ID_ERROR	INITIATOR_ERROR
+#define	M_ABORT		ABORT_TASK_SET
+#define	M_REJECT	MESSAGE_REJECT
+#define	M_NOOP		NOP
+#define	M_PARITY	MSG_PARITY_ERROR
+#define	M_LCOMPLETE	LINKED_CMD_COMPLETE
+#define	M_FCOMPLETE	LINKED_FLG_CMD_COMPLETE
+#define	M_RESET		TARGET_RESET
+#define	M_ABORT_TAG	ABORT_TASK
+#define	M_CLEAR_QUEUE	CLEAR_TASK_SET
+#define	M_INIT_REC	INITIATE_RECOVERY
+#define	M_REL_REC	RELEASE_RECOVERY
+#define	M_TERMINATE	(0x11)
+#define	M_SIMPLE_TAG	SIMPLE_QUEUE_TAG
+#define	M_HEAD_TAG	HEAD_OF_QUEUE_TAG
+#define	M_ORDERED_TAG	ORDERED_QUEUE_TAG
+#define	M_IGN_RESIDUE	IGNORE_WIDE_RESIDUE
+#define	M_IDENTIFY   	(0x80)
+
+#define	M_X_MODIFY_DP	EXTENDED_MODIFY_DATA_POINTER
+#define	M_X_SYNC_REQ	EXTENDED_SDTR
+#define	M_X_WIDE_REQ	EXTENDED_WDTR
+#define	M_X_PPR_REQ	EXTENDED_PPR
+
+/*
+**	Status
+*/
+
+#define	S_GOOD		(0x00)
+#define	S_CHECK_COND	(0x02)
+#define	S_COND_MET	(0x04)
+#define	S_BUSY		(0x08)
+#define	S_INT		(0x10)
+#define	S_INT_COND_MET	(0x14)
+#define	S_CONFLICT	(0x18)
+#define	S_TERMINATED	(0x20)
+#define	S_QUEUE_FULL	(0x28)
+#define	S_ILLEGAL	(0xff)
+#define	S_SENSE		(0x80)
+
+/*
+ * End of ncrreg from FreeBSD
+ */
 
 /*
 	Build a scatter/gather entry.