Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support
for Broadcom's STB SoC -- it was accidentally merged before some
issues had been addressed, so they will make a new attempt for 3.18.
I didn't see a need for a full revert of the whole platform due to
this, we're keeping the rest enabled.
The rest is mostly:
- a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
- some MTD/NAND fixes for OMAP
- minor DT fixes for shmobile
- warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's
small and isolated so it made sense to pick up now even if it's not a
bugfix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
vexpress/spc: fix a build warning on array bounds
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
MAINTAINERS: catch special Rockchip code locations
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
ARM: brcmstb: revert SMP support
ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
ARM: dts: Enable UART wake-up events for beagleboard
ARM: dts: Remove twl6030 clk32g "regulator"
ARM: OMAP2+: omap_device: remove warning that clk alias already exists
ARM: OMAP: fix %d confusingly prefixed with 0x in format string
ARM: dts: DRA7: fix interrupt-cells for GPIO
mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
mtd: nand: omap: Revert to using software ECC by default
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
...
diff --git a/Documentation/devicetree/bindings/mfd/tc3589x.txt b/Documentation/devicetree/bindings/mfd/tc3589x.txt
new file mode 100644
index 0000000..6fcedba
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/tc3589x.txt
@@ -0,0 +1,107 @@
+* Toshiba TC3589x multi-purpose expander
+
+The Toshiba TC3589x series are I2C-based MFD devices which may expose the
+following built-in devices: gpio, keypad, rotator (vibrator), PWM (for
+e.g. LEDs or vibrators) The included models are:
+
+- TC35890
+- TC35892
+- TC35893
+- TC35894
+- TC35895
+- TC35896
+
+Required properties:
+ - compatible : must be "toshiba,tc35890", "toshiba,tc35892", "toshiba,tc35893",
+ "toshiba,tc35894", "toshiba,tc35895" or "toshiba,tc35896"
+ - reg : I2C address of the device
+ - interrupt-parent : specifies which IRQ controller we're connected to
+ - interrupts : the interrupt on the parent the controller is connected to
+ - interrupt-controller : marks the device node as an interrupt controller
+ - #interrupt-cells : should be <1>, the first cell is the IRQ offset on this
+ TC3589x interrupt controller.
+
+Optional nodes:
+
+- GPIO
+ This GPIO module inside the TC3589x has 24 (TC35890, TC35892) or 20
+ (other models) GPIO lines.
+ - compatible : must be "toshiba,tc3589x-gpio"
+ - interrupts : interrupt on the parent, which must be the tc3589x MFD device
+ - interrupt-controller : marks the device node as an interrupt controller
+ - #interrupt-cells : should be <2>, the first cell is the IRQ offset on this
+ TC3589x GPIO interrupt controller, the second cell is the interrupt flags
+ in accordance with <dt-bindings/interrupt-controller/irq.h>. The following
+ flags are valid:
+ - IRQ_TYPE_LEVEL_LOW
+ - IRQ_TYPE_LEVEL_HIGH
+ - IRQ_TYPE_EDGE_RISING
+ - IRQ_TYPE_EDGE_FALLING
+ - IRQ_TYPE_EDGE_BOTH
+ - gpio-controller : marks the device node as a GPIO controller
+ - #gpio-cells : should be <2>, the first cell is the GPIO offset on this
+ GPIO controller, the second cell is the flags.
+
+- Keypad
+ This keypad is the same on all variants, supporting up to 96 different
+ keys. The linux-specific properties are modeled on those already existing
+ in other input drivers.
+ - compatible : must be "toshiba,tc3589x-keypad"
+ - debounce-delay-ms : debounce interval in milliseconds
+ - keypad,num-rows : number of rows in the matrix, see
+ bindings/input/matrix-keymap.txt
+ - keypad,num-columns : number of columns in the matrix, see
+ bindings/input/matrix-keymap.txt
+ - linux,keymap: the definition can be found in
+ bindings/input/matrix-keymap.txt
+ - linux,no-autorepeat: do no enable autorepeat feature.
+ - linux,wakeup: use any event on keypad as wakeup event.
+
+Example:
+
+tc35893@44 {
+ compatible = "toshiba,tc35893";
+ reg = <0x44>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ tc3589x_gpio {
+ compatible = "toshiba,tc3589x-gpio";
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ tc3589x_keypad {
+ compatible = "toshiba,tc3589x-keypad";
+ interrupts = <6>;
+ debounce-delay-ms = <4>;
+ keypad,num-columns = <8>;
+ keypad,num-rows = <8>;
+ linux,no-autorepeat;
+ linux,wakeup;
+ linux,keymap = <0x0301006b
+ 0x04010066
+ 0x06040072
+ 0x040200d7
+ 0x0303006a
+ 0x0205000e
+ 0x0607008b
+ 0x0500001c
+ 0x0403000b
+ 0x03040034
+ 0x05020067
+ 0x0305006c
+ 0x040500e7
+ 0x0005009e
+ 0x06020073
+ 0x01030039
+ 0x07060069
+ 0x050500d9>;
+ };
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
index 0211c6d..92fae82 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
@@ -62,7 +62,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
- interrupts = <0 32 0x4>;
+ interrupts = <0 16 0x4>;
pinctrl-names = "default";
pinctrl-0 = <&gsbi5_uart_default>;
diff --git a/Documentation/dma-buf-sharing.txt b/Documentation/dma-buf-sharing.txt
index 67a4087..bb9753b 100644
--- a/Documentation/dma-buf-sharing.txt
+++ b/Documentation/dma-buf-sharing.txt
@@ -56,10 +56,10 @@
size_t size, int flags,
const char *exp_name)
- If this succeeds, dma_buf_export allocates a dma_buf structure, and returns a
- pointer to the same. It also associates an anonymous file with this buffer,
- so it can be exported. On failure to allocate the dma_buf object, it returns
- NULL.
+ If this succeeds, dma_buf_export_named allocates a dma_buf structure, and
+ returns a pointer to the same. It also associates an anonymous file with this
+ buffer, so it can be exported. On failure to allocate the dma_buf object,
+ it returns NULL.
'exp_name' is the name of exporter - to facilitate information while
debugging.
@@ -76,7 +76,7 @@
drivers and/or processes.
Interface:
- int dma_buf_fd(struct dma_buf *dmabuf)
+ int dma_buf_fd(struct dma_buf *dmabuf, int flags)
This API installs an fd for the anonymous file associated with this buffer;
returns either 'fd', or error.
@@ -157,7 +157,9 @@
"dma_buf->ops->" indirection from the users of this interface.
In struct dma_buf_ops, unmap_dma_buf is defined as
- void (*unmap_dma_buf)(struct dma_buf_attachment *, struct sg_table *);
+ void (*unmap_dma_buf)(struct dma_buf_attachment *,
+ struct sg_table *,
+ enum dma_data_direction);
unmap_dma_buf signifies the end-of-DMA for the attachment provided. Like
map_dma_buf, this API also must be implemented by the exporter.
diff --git a/Documentation/kdump/kdump.txt b/Documentation/kdump/kdump.txt
index 88d5a86..6c0b9f2 100644
--- a/Documentation/kdump/kdump.txt
+++ b/Documentation/kdump/kdump.txt
@@ -18,7 +18,7 @@
a remote system.
Kdump and kexec are currently supported on the x86, x86_64, ppc64, ia64,
-and s390x architectures.
+s390x and arm architectures.
When the system kernel boots, it reserves a small section of memory for
the dump-capture kernel. This ensures that ongoing Direct Memory Access
@@ -112,7 +112,7 @@
2) Or use the system kernel binary itself as dump-capture kernel and there is
no need to build a separate dump-capture kernel. This is possible
only with the architectures which support a relocatable kernel. As
- of today, i386, x86_64, ppc64 and ia64 architectures support relocatable
+ of today, i386, x86_64, ppc64, ia64 and arm architectures support relocatable
kernel.
Building a relocatable kernel is advantageous from the point of view that
@@ -241,6 +241,13 @@
kernel will be aligned to 64Mb, so if the start address is not then
any space below the alignment point will be wasted.
+Dump-capture kernel config options (Arch Dependent, arm)
+----------------------------------------------------------
+
+- To use a relocatable kernel,
+ Enable "AUTO_ZRELADDR" support under "Boot" options:
+
+ AUTO_ZRELADDR=y
Extended crashkernel syntax
===========================
@@ -256,6 +263,10 @@
crashkernel=<range1>:<size1>[,<range2>:<size2>,...][@offset]
range=start-[end]
+Please note, on arm, the offset is required.
+ crashkernel=<range1>:<size1>[,<range2>:<size2>,...]@offset
+ range=start-[end]
+
'start' is inclusive and 'end' is exclusive.
For example:
@@ -296,6 +307,12 @@
on the memory consumption of the kdump system. In general this is not
dependent on the memory size of the production system.
+ On arm, use "crashkernel=Y@X". Note that the start address of the kernel
+ will be aligned to 128MiB (0x08000000), so if the start address is not then
+ any space below the alignment point may be overwritten by the dump-capture kernel,
+ which means it is possible that the vmcore is not that precise as expected.
+
+
Load the Dump-capture Kernel
============================
@@ -315,7 +332,8 @@
- Use vmlinux or vmlinuz.gz
For s390x:
- Use image or bzImage
-
+For arm:
+ - Use zImage
If you are using a uncompressed vmlinux image then use following command
to load dump-capture kernel.
@@ -331,6 +349,15 @@
--initrd=<initrd-for-dump-capture-kernel> \
--append="root=<root-dev> <arch-specific-options>"
+If you are using a compressed zImage, then use following command
+to load dump-capture kernel.
+
+ kexec --type zImage -p <dump-capture-kernel-bzImage> \
+ --initrd=<initrd-for-dump-capture-kernel> \
+ --dtb=<dtb-for-dump-capture-kernel> \
+ --append="root=<root-dev> <arch-specific-options>"
+
+
Please note, that --args-linux does not need to be specified for ia64.
It is planned to make this a no-op on that architecture, but for now
it should be omitted
@@ -347,6 +374,9 @@
For s390x:
"1 maxcpus=1 cgroup_disable=memory"
+For arm:
+ "1 maxcpus=1 reset_devices"
+
Notes on loading the dump-capture kernel:
* By default, the ELF headers are stored in ELF64 format to support
diff --git a/Documentation/this_cpu_ops.txt b/Documentation/this_cpu_ops.txt
index 1a4ce7e..0ec9957 100644
--- a/Documentation/this_cpu_ops.txt
+++ b/Documentation/this_cpu_ops.txt
@@ -2,26 +2,26 @@
-------------------
this_cpu operations are a way of optimizing access to per cpu
-variables associated with the *currently* executing processor through
-the use of segment registers (or a dedicated register where the cpu
-permanently stored the beginning of the per cpu area for a specific
-processor).
+variables associated with the *currently* executing processor. This is
+done through the use of segment registers (or a dedicated register where
+the cpu permanently stored the beginning of the per cpu area for a
+specific processor).
-The this_cpu operations add a per cpu variable offset to the processor
-specific percpu base and encode that operation in the instruction
+this_cpu operations add a per cpu variable offset to the processor
+specific per cpu base and encode that operation in the instruction
operating on the per cpu variable.
-This means there are no atomicity issues between the calculation of
+This means that there are no atomicity issues between the calculation of
the offset and the operation on the data. Therefore it is not
-necessary to disable preempt or interrupts to ensure that the
+necessary to disable preemption or interrupts to ensure that the
processor is not changed between the calculation of the address and
the operation on the data.
Read-modify-write operations are of particular interest. Frequently
processors have special lower latency instructions that can operate
-without the typical synchronization overhead but still provide some
-sort of relaxed atomicity guarantee. The x86 for example can execute
-RMV (Read Modify Write) instructions like inc/dec/cmpxchg without the
+without the typical synchronization overhead, but still provide some
+sort of relaxed atomicity guarantees. The x86, for example, can execute
+RMW (Read Modify Write) instructions like inc/dec/cmpxchg without the
lock prefix and the associated latency penalty.
Access to the variable without the lock prefix is not synchronized but
@@ -30,6 +30,38 @@
processor should be accessing that variable and therefore there are no
concurrency issues with other processors in the system.
+Please note that accesses by remote processors to a per cpu area are
+exceptional situations and may impact performance and/or correctness
+(remote write operations) of local RMW operations via this_cpu_*.
+
+The main use of the this_cpu operations has been to optimize counter
+operations.
+
+The following this_cpu() operations with implied preemption protection
+are defined. These operations can be used without worrying about
+preemption and interrupts.
+
+ this_cpu_add()
+ this_cpu_read(pcp)
+ this_cpu_write(pcp, val)
+ this_cpu_add(pcp, val)
+ this_cpu_and(pcp, val)
+ this_cpu_or(pcp, val)
+ this_cpu_add_return(pcp, val)
+ this_cpu_xchg(pcp, nval)
+ this_cpu_cmpxchg(pcp, oval, nval)
+ this_cpu_cmpxchg_double(pcp1, pcp2, oval1, oval2, nval1, nval2)
+ this_cpu_sub(pcp, val)
+ this_cpu_inc(pcp)
+ this_cpu_dec(pcp)
+ this_cpu_sub_return(pcp, val)
+ this_cpu_inc_return(pcp)
+ this_cpu_dec_return(pcp)
+
+
+Inner working of this_cpu operations
+------------------------------------
+
On x86 the fs: or the gs: segment registers contain the base of the
per cpu area. It is then possible to simply use the segment override
to relocate a per cpu relative address to the proper per cpu area for
@@ -48,22 +80,21 @@
mov ax, gs:[x]
instead of a sequence of calculation of the address and then a fetch
-from that address which occurs with the percpu operations. Before
+from that address which occurs with the per cpu operations. Before
this_cpu_ops such sequence also required preempt disable/enable to
prevent the kernel from moving the thread to a different processor
while the calculation is performed.
-The main use of the this_cpu operations has been to optimize counter
-operations.
+Consider the following this_cpu operation:
this_cpu_inc(x)
-results in the following single instruction (no lock prefix!)
+The above results in the following single instruction (no lock prefix!)
inc gs:[x]
instead of the following operations required if there is no segment
-register.
+register:
int *y;
int cpu;
@@ -73,10 +104,10 @@
(*y)++;
put_cpu();
-Note that these operations can only be used on percpu data that is
+Note that these operations can only be used on per cpu data that is
reserved for a specific processor. Without disabling preemption in the
surrounding code this_cpu_inc() will only guarantee that one of the
-percpu counters is correctly incremented. However, there is no
+per cpu counters is correctly incremented. However, there is no
guarantee that the OS will not move the process directly before or
after the this_cpu instruction is executed. In general this means that
the value of the individual counters for each processor are
@@ -86,9 +117,9 @@
Per cpu variables are used for performance reasons. Bouncing cache
lines can be avoided if multiple processors concurrently go through
the same code paths. Since each processor has its own per cpu
-variables no concurrent cacheline updates take place. The price that
+variables no concurrent cache line updates take place. The price that
has to be paid for this optimization is the need to add up the per cpu
-counters when the value of the counter is needed.
+counters when the value of a counter is needed.
Special operations:
@@ -100,33 +131,39 @@
of the per cpu variable that belongs to the currently executing
processor. this_cpu_ptr avoids multiple steps that the common
get_cpu/put_cpu sequence requires. No processor number is
-available. Instead the offset of the local per cpu area is simply
-added to the percpu offset.
+available. Instead, the offset of the local per cpu area is simply
+added to the per cpu offset.
+Note that this operation is usually used in a code segment when
+preemption has been disabled. The pointer is then used to
+access local per cpu data in a critical section. When preemption
+is re-enabled this pointer is usually no longer useful since it may
+no longer point to per cpu data of the current processor.
Per cpu variables and offsets
-----------------------------
-Per cpu variables have *offsets* to the beginning of the percpu
+Per cpu variables have *offsets* to the beginning of the per cpu
area. They do not have addresses although they look like that in the
code. Offsets cannot be directly dereferenced. The offset must be
-added to a base pointer of a percpu area of a processor in order to
+added to a base pointer of a per cpu area of a processor in order to
form a valid address.
Therefore the use of x or &x outside of the context of per cpu
operations is invalid and will generally be treated like a NULL
pointer dereference.
-In the context of per cpu operations
+ DEFINE_PER_CPU(int, x);
- x is a per cpu variable. Most this_cpu operations take a cpu
- variable.
+In the context of per cpu operations the above implies that x is a per
+cpu variable. Most this_cpu operations take a cpu variable.
- &x is the *offset* a per cpu variable. this_cpu_ptr() takes
- the offset of a per cpu variable which makes this look a bit
- strange.
+ int __percpu *p = &x;
+&x and hence p is the *offset* of a per cpu variable. this_cpu_ptr()
+takes the offset of a per cpu variable which makes this look a bit
+strange.
Operations on a field of a per cpu structure
@@ -152,7 +189,7 @@
struct s __percpu *ps = &p;
- z = this_cpu_dec(ps->m);
+ this_cpu_dec(ps->m);
z = this_cpu_inc_return(ps->n);
@@ -172,29 +209,52 @@
Variants of this_cpu ops
-------------------------
-this_cpu ops are interrupt safe. Some architecture do not support
+this_cpu ops are interrupt safe. Some architectures do not support
these per cpu local operations. In that case the operation must be
replaced by code that disables interrupts, then does the operations
-that are guaranteed to be atomic and then reenable interrupts. Doing
+that are guaranteed to be atomic and then re-enable interrupts. Doing
so is expensive. If there are other reasons why the scheduler cannot
change the processor we are executing on then there is no reason to
-disable interrupts. For that purpose the __this_cpu operations are
-provided. For example.
+disable interrupts. For that purpose the following __this_cpu operations
+are provided.
- __this_cpu_inc(x);
+These operations have no guarantee against concurrent interrupts or
+preemption. If a per cpu variable is not used in an interrupt context
+and the scheduler cannot preempt, then they are safe. If any interrupts
+still occur while an operation is in progress and if the interrupt too
+modifies the variable, then RMW actions can not be guaranteed to be
+safe.
-Will increment x and will not fallback to code that disables
+ __this_cpu_add()
+ __this_cpu_read(pcp)
+ __this_cpu_write(pcp, val)
+ __this_cpu_add(pcp, val)
+ __this_cpu_and(pcp, val)
+ __this_cpu_or(pcp, val)
+ __this_cpu_add_return(pcp, val)
+ __this_cpu_xchg(pcp, nval)
+ __this_cpu_cmpxchg(pcp, oval, nval)
+ __this_cpu_cmpxchg_double(pcp1, pcp2, oval1, oval2, nval1, nval2)
+ __this_cpu_sub(pcp, val)
+ __this_cpu_inc(pcp)
+ __this_cpu_dec(pcp)
+ __this_cpu_sub_return(pcp, val)
+ __this_cpu_inc_return(pcp)
+ __this_cpu_dec_return(pcp)
+
+
+Will increment x and will not fall-back to code that disables
interrupts on platforms that cannot accomplish atomicity through
address relocation and a Read-Modify-Write operation in the same
instruction.
-
&this_cpu_ptr(pp)->n vs this_cpu_ptr(&pp->n)
--------------------------------------------
The first operation takes the offset and forms an address and then
-adds the offset of the n field.
+adds the offset of the n field. This may result in two add
+instructions emitted by the compiler.
The second one first adds the two offsets and then does the
relocation. IMHO the second form looks cleaner and has an easier time
@@ -202,4 +262,73 @@
this_cpu_read() and friends are used.
-Christoph Lameter, April 3rd, 2013
+Remote access to per cpu data
+------------------------------
+
+Per cpu data structures are designed to be used by one cpu exclusively.
+If you use the variables as intended, this_cpu_ops() are guaranteed to
+be "atomic" as no other CPU has access to these data structures.
+
+There are special cases where you might need to access per cpu data
+structures remotely. It is usually safe to do a remote read access
+and that is frequently done to summarize counters. Remote write access
+something which could be problematic because this_cpu ops do not
+have lock semantics. A remote write may interfere with a this_cpu
+RMW operation.
+
+Remote write accesses to percpu data structures are highly discouraged
+unless absolutely necessary. Please consider using an IPI to wake up
+the remote CPU and perform the update to its per cpu area.
+
+To access per-cpu data structure remotely, typically the per_cpu_ptr()
+function is used:
+
+
+ DEFINE_PER_CPU(struct data, datap);
+
+ struct data *p = per_cpu_ptr(&datap, cpu);
+
+This makes it explicit that we are getting ready to access a percpu
+area remotely.
+
+You can also do the following to convert the datap offset to an address
+
+ struct data *p = this_cpu_ptr(&datap);
+
+but, passing of pointers calculated via this_cpu_ptr to other cpus is
+unusual and should be avoided.
+
+Remote access are typically only for reading the status of another cpus
+per cpu data. Write accesses can cause unique problems due to the
+relaxed synchronization requirements for this_cpu operations.
+
+One example that illustrates some concerns with write operations is
+the following scenario that occurs because two per cpu variables
+share a cache-line but the relaxed synchronization is applied to
+only one process updating the cache-line.
+
+Consider the following example
+
+
+ struct test {
+ atomic_t a;
+ int b;
+ };
+
+ DEFINE_PER_CPU(struct test, onecacheline);
+
+There is some concern about what would happen if the field 'a' is updated
+remotely from one processor and the local processor would use this_cpu ops
+to update field b. Care should be taken that such simultaneous accesses to
+data within the same cache line are avoided. Also costly synchronization
+may be necessary. IPIs are generally recommended in such scenarios instead
+of a remote write to the per cpu area of another processor.
+
+Even in cases where the remote writes are rare, please bear in
+mind that a remote write will evict the cache line from the processor
+that most likely will access it. If the processor wakes up and finds a
+missing local cache line of a per cpu area, its performance and hence
+the wake up times will be affected.
+
+Christoph Lameter, August 4th, 2014
+Pranith Kumar, Aug 2nd, 2014
diff --git a/MAINTAINERS b/MAINTAINERS
index 93e9f73..cf24bb5 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9562,6 +9562,14 @@
F: Documentation/usb/ohci.txt
F: drivers/usb/host/ohci*
+USB OVER IP DRIVER
+M: Valentina Manea <valentina.manea.m@gmail.com>
+M: Shuah Khan <shuah.kh@samsung.com>
+L: linux-usb@vger.kernel.org
+S: Maintained
+F: drivers/usb/usbip/
+F: tools/usb/usbip/
+
USB PEGASUS DRIVER
M: Petko Manolov <petkan@nucleusys.com>
L: linux-usb@vger.kernel.org
diff --git a/arch/alpha/include/asm/io.h b/arch/alpha/include/asm/io.h
index 5ebab58..f05bdb4 100644
--- a/arch/alpha/include/asm/io.h
+++ b/arch/alpha/include/asm/io.h
@@ -500,10 +500,14 @@
#define outb_p outb
#define outw_p outw
#define outl_p outl
-#define readb_relaxed(addr) __raw_readb(addr)
-#define readw_relaxed(addr) __raw_readw(addr)
-#define readl_relaxed(addr) __raw_readl(addr)
-#define readq_relaxed(addr) __raw_readq(addr)
+#define readb_relaxed(addr) __raw_readb(addr)
+#define readw_relaxed(addr) __raw_readw(addr)
+#define readl_relaxed(addr) __raw_readl(addr)
+#define readq_relaxed(addr) __raw_readq(addr)
+#define writeb_relaxed(b, addr) __raw_writeb(b, addr)
+#define writew_relaxed(b, addr) __raw_writew(b, addr)
+#define writel_relaxed(b, addr) __raw_writel(b, addr)
+#define writeq_relaxed(b, addr) __raw_writeq(b, addr)
#define mmiowb()
diff --git a/arch/alpha/include/asm/unistd.h b/arch/alpha/include/asm/unistd.h
index f2c9440..c509d30 100644
--- a/arch/alpha/include/asm/unistd.h
+++ b/arch/alpha/include/asm/unistd.h
@@ -3,7 +3,7 @@
#include <uapi/asm/unistd.h>
-#define NR_SYSCALLS 508
+#define NR_SYSCALLS 511
#define __ARCH_WANT_OLD_READDIR
#define __ARCH_WANT_STAT64
diff --git a/arch/alpha/include/uapi/asm/unistd.h b/arch/alpha/include/uapi/asm/unistd.h
index 53ae7bb..d214a035 100644
--- a/arch/alpha/include/uapi/asm/unistd.h
+++ b/arch/alpha/include/uapi/asm/unistd.h
@@ -469,5 +469,8 @@
#define __NR_process_vm_writev 505
#define __NR_kcmp 506
#define __NR_finit_module 507
+#define __NR_sched_setattr 508
+#define __NR_sched_getattr 509
+#define __NR_renameat2 510
#endif /* _UAPI_ALPHA_UNISTD_H */
diff --git a/arch/alpha/kernel/systbls.S b/arch/alpha/kernel/systbls.S
index dca9b3f..24789713 100644
--- a/arch/alpha/kernel/systbls.S
+++ b/arch/alpha/kernel/systbls.S
@@ -526,6 +526,9 @@
.quad sys_process_vm_writev /* 505 */
.quad sys_kcmp
.quad sys_finit_module
+ .quad sys_sched_setattr
+ .quad sys_sched_getattr
+ .quad sys_renameat2 /* 510 */
.size sys_call_table, . - sys_call_table
.type sys_call_table, @object
diff --git a/arch/arc/mm/cache_arc700.c b/arch/arc/mm/cache_arc700.c
index 4670afc..e88ddbf 100644
--- a/arch/arc/mm/cache_arc700.c
+++ b/arch/arc/mm/cache_arc700.c
@@ -581,6 +581,7 @@
tot_sz -= sz;
}
}
+EXPORT_SYMBOL(flush_icache_range);
/*
* General purpose helper to make I and D cache lines consistent.
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c49a775..32cbbd5 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1983,8 +1983,6 @@
config KEXEC
bool "Kexec system call (EXPERIMENTAL)"
depends on (!SMP || PM_SLEEP_SMP)
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index b15f1a7..1fe45d1 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -353,7 +353,7 @@
};
twl_power: power {
- compatible = "ti,twl4030-power-n900";
+ compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off";
ti,use_poweroff;
};
};
diff --git a/arch/hexagon/mm/cache.c b/arch/hexagon/mm/cache.c
index fe14ccf..0c76c80 100644
--- a/arch/hexagon/mm/cache.c
+++ b/arch/hexagon/mm/cache.c
@@ -68,6 +68,7 @@
);
local_irq_restore(flags);
}
+EXPORT_SYMBOL(flush_icache_range);
void hexagon_clean_dcache_range(unsigned long start, unsigned long end)
{
diff --git a/arch/ia64/Kconfig b/arch/ia64/Kconfig
index 64aefb7..c84c88b 100644
--- a/arch/ia64/Kconfig
+++ b/arch/ia64/Kconfig
@@ -549,8 +549,6 @@
config KEXEC
bool "kexec system call"
depends on !IA64_HP_SIM && (!SMP || HOTPLUG_CPU)
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
diff --git a/arch/m68k/Kconfig b/arch/m68k/Kconfig
index 3ff8c9a..87b7c75 100644
--- a/arch/m68k/Kconfig
+++ b/arch/m68k/Kconfig
@@ -91,8 +91,6 @@
config KEXEC
bool "kexec system call"
depends on M68KCLASSIC
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index df51e78..900c7e5 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -2396,8 +2396,6 @@
config KEXEC
bool "Kexec system call"
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index a577609f..4bc7b62 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -399,8 +399,6 @@
config KEXEC
bool "kexec system call"
depends on (PPC_BOOK3S || FSL_BOOKE || (44x && !SMP))
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
diff --git a/arch/s390/Kconfig b/arch/s390/Kconfig
index ab39ceb8..05c78bb 100644
--- a/arch/s390/Kconfig
+++ b/arch/s390/Kconfig
@@ -48,8 +48,6 @@
config KEXEC
def_bool y
- select CRYPTO
- select CRYPTO_SHA256
config AUDIT_ARCH
def_bool y
diff --git a/arch/s390/include/uapi/asm/unistd.h b/arch/s390/include/uapi/asm/unistd.h
index 3802d2d..940ac49 100644
--- a/arch/s390/include/uapi/asm/unistd.h
+++ b/arch/s390/include/uapi/asm/unistd.h
@@ -283,7 +283,10 @@
#define __NR_sched_setattr 345
#define __NR_sched_getattr 346
#define __NR_renameat2 347
-#define NR_syscalls 348
+#define __NR_seccomp 348
+#define __NR_getrandom 349
+#define __NR_memfd_create 350
+#define NR_syscalls 351
/*
* There are some system calls that are not present on 64 bit, some
diff --git a/arch/s390/kernel/compat_wrapper.c b/arch/s390/kernel/compat_wrapper.c
index 45cdb37..faf6caa 100644
--- a/arch/s390/kernel/compat_wrapper.c
+++ b/arch/s390/kernel/compat_wrapper.c
@@ -214,3 +214,6 @@
COMPAT_SYSCALL_WRAP3(sched_setattr, pid_t, pid, struct sched_attr __user *, attr, unsigned int, flags);
COMPAT_SYSCALL_WRAP4(sched_getattr, pid_t, pid, struct sched_attr __user *, attr, unsigned int, size, unsigned int, flags);
COMPAT_SYSCALL_WRAP5(renameat2, int, olddfd, const char __user *, oldname, int, newdfd, const char __user *, newname, unsigned int, flags);
+COMPAT_SYSCALL_WRAP3(seccomp, unsigned int, op, unsigned int, flags, const char __user *, uargs)
+COMPAT_SYSCALL_WRAP3(getrandom, char __user *, buf, size_t, count, unsigned int, flags)
+COMPAT_SYSCALL_WRAP2(memfd_create, const char __user *, uname, unsigned int, flags)
diff --git a/arch/s390/kernel/ipl.c b/arch/s390/kernel/ipl.c
index 633ca75..22aac58 100644
--- a/arch/s390/kernel/ipl.c
+++ b/arch/s390/kernel/ipl.c
@@ -2060,6 +2060,13 @@
S390_lowcore.program_new_psw.addr =
PSW_ADDR_AMODE | (unsigned long) s390_base_pgm_handler;
+ /*
+ * Clear subchannel ID and number to signal new kernel that no CCW or
+ * SCSI IPL has been done (for kexec and kdump)
+ */
+ S390_lowcore.subchannel_id = 0;
+ S390_lowcore.subchannel_nr = 0;
+
/* Store status at absolute zero */
store_status();
diff --git a/arch/s390/kernel/setup.c b/arch/s390/kernel/setup.c
index ae1d5be..82bc113 100644
--- a/arch/s390/kernel/setup.c
+++ b/arch/s390/kernel/setup.c
@@ -24,6 +24,7 @@
#include <linux/stddef.h>
#include <linux/unistd.h>
#include <linux/ptrace.h>
+#include <linux/random.h>
#include <linux/user.h>
#include <linux/tty.h>
#include <linux/ioport.h>
@@ -61,6 +62,7 @@
#include <asm/diag.h>
#include <asm/os_info.h>
#include <asm/sclp.h>
+#include <asm/sysinfo.h>
#include "entry.h"
/*
@@ -766,6 +768,7 @@
#endif
get_cpu_id(&cpu_id);
+ add_device_randomness(&cpu_id, sizeof(cpu_id));
switch (cpu_id.machine) {
case 0x9672:
#if !defined(CONFIG_64BIT)
@@ -804,6 +807,19 @@
}
/*
+ * Add system information as device randomness
+ */
+static void __init setup_randomness(void)
+{
+ struct sysinfo_3_2_2 *vmms;
+
+ vmms = (struct sysinfo_3_2_2 *) alloc_page(GFP_KERNEL);
+ if (vmms && stsi(vmms, 3, 2, 2) == 0 && vmms->count)
+ add_device_randomness(&vmms, vmms->count);
+ free_page((unsigned long) vmms);
+}
+
+/*
* Setup function called from init/main.c just after the banner
* was printed.
*/
@@ -901,6 +917,9 @@
/* Setup zfcpdump support */
setup_zfcpdump();
+
+ /* Add system specific data to the random pool */
+ setup_randomness();
}
#ifdef CONFIG_32BIT
diff --git a/arch/s390/kernel/syscalls.S b/arch/s390/kernel/syscalls.S
index fe5cdf2..6fe886a 100644
--- a/arch/s390/kernel/syscalls.S
+++ b/arch/s390/kernel/syscalls.S
@@ -356,3 +356,6 @@
SYSCALL(sys_sched_setattr,sys_sched_setattr,compat_sys_sched_setattr) /* 345 */
SYSCALL(sys_sched_getattr,sys_sched_getattr,compat_sys_sched_getattr)
SYSCALL(sys_renameat2,sys_renameat2,compat_sys_renameat2)
+SYSCALL(sys_seccomp,sys_seccomp,compat_sys_seccomp)
+SYSCALL(sys_getrandom,sys_getrandom,compat_sys_getrandom)
+SYSCALL(sys_memfd_create,sys_memfd_create,compat_sys_memfd_create) /* 350 */
diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig
index b319846..244fb4c 100644
--- a/arch/sh/Kconfig
+++ b/arch/sh/Kconfig
@@ -598,8 +598,6 @@
config KEXEC
bool "kexec system call (EXPERIMENTAL)"
depends on SUPERH32 && MMU
- select CRYPTO
- select CRYPTO_SHA256
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
diff --git a/arch/sh/mm/cache.c b/arch/sh/mm/cache.c
index 097c2cd..f770e39 100644
--- a/arch/sh/mm/cache.c
+++ b/arch/sh/mm/cache.c
@@ -229,6 +229,7 @@
cacheop_on_each_cpu(local_flush_icache_range, (void *)&data, 1);
}
+EXPORT_SYMBOL(flush_icache_range);
void flush_icache_page(struct vm_area_struct *vma, struct page *page)
{
diff --git a/arch/tile/Kconfig b/arch/tile/Kconfig
index a3ffe2d..7fcd492 100644
--- a/arch/tile/Kconfig
+++ b/arch/tile/Kconfig
@@ -191,8 +191,6 @@
config KEXEC
bool "kexec system call"
- select CRYPTO
- select CRYPTO_SHA256
---help---
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
diff --git a/arch/tile/kernel/smp.c b/arch/tile/kernel/smp.c
index 01e8ab2..19eaa62 100644
--- a/arch/tile/kernel/smp.c
+++ b/arch/tile/kernel/smp.c
@@ -183,6 +183,7 @@
preempt_enable();
}
}
+EXPORT_SYMBOL(flush_icache_range);
/* Called when smp_send_reschedule() triggers IRQ_RESCHEDULE. */
diff --git a/arch/x86/Kbuild b/arch/x86/Kbuild
index 61b6d51..3942f74 100644
--- a/arch/x86/Kbuild
+++ b/arch/x86/Kbuild
@@ -17,6 +17,4 @@
obj-y += platform/
obj-y += net/
-ifeq ($(CONFIG_X86_64),y)
-obj-$(CONFIG_KEXEC) += purgatory/
-endif
+obj-$(CONFIG_KEXEC_FILE) += purgatory/
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 5d0bf1a..778178f 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -1585,9 +1585,6 @@
config KEXEC
bool "kexec system call"
- select BUILD_BIN2C
- select CRYPTO
- select CRYPTO_SHA256
---help---
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
@@ -1602,9 +1599,22 @@
interface is strongly in flux, so no good recommendation can be
made.
+config KEXEC_FILE
+ bool "kexec file based system call"
+ select BUILD_BIN2C
+ depends on KEXEC
+ depends on X86_64
+ depends on CRYPTO=y
+ depends on CRYPTO_SHA256=y
+ ---help---
+ This is new version of kexec system call. This system call is
+ file based and takes file descriptors as system call argument
+ for kernel and initramfs as opposed to list of segments as
+ accepted by previous system call.
+
config KEXEC_VERIFY_SIG
bool "Verify kernel signature during kexec_file_load() syscall"
- depends on KEXEC
+ depends on KEXEC_FILE
---help---
This option makes kernel signature verification mandatory for
kexec_file_load() syscall. If kernel is signature can not be
diff --git a/arch/x86/Makefile b/arch/x86/Makefile
index c1aa368..60087ca 100644
--- a/arch/x86/Makefile
+++ b/arch/x86/Makefile
@@ -184,11 +184,8 @@
$(Q)$(MAKE) $(build)=arch/x86/syscalls all
archprepare:
-ifeq ($(CONFIG_KEXEC),y)
-# Build only for 64bit. No loaders for 32bit yet.
- ifeq ($(CONFIG_X86_64),y)
+ifeq ($(CONFIG_KEXEC_FILE),y)
$(Q)$(MAKE) $(build)=arch/x86/purgatory arch/x86/purgatory/kexec-purgatory.c
- endif
endif
###
@@ -254,6 +251,7 @@
$(Q)rm -rf $(objtree)/arch/x86_64
$(Q)$(MAKE) $(clean)=$(boot)
$(Q)$(MAKE) $(clean)=arch/x86/tools
+ $(Q)$(MAKE) $(clean)=arch/x86/purgatory
PHONY += kvmconfig
kvmconfig:
diff --git a/arch/x86/include/asm/io_apic.h b/arch/x86/include/asm/io_apic.h
index 0aeed5c..478c490 100644
--- a/arch/x86/include/asm/io_apic.h
+++ b/arch/x86/include/asm/io_apic.h
@@ -227,6 +227,8 @@
extern void io_apic_eoi(unsigned int apic, unsigned int vector);
+extern bool mp_should_keep_irq(struct device *dev);
+
#else /* !CONFIG_X86_IO_APIC */
#define io_apic_assign_pci_irqs 0
diff --git a/arch/x86/include/asm/pgtable.h b/arch/x86/include/asm/pgtable.h
index 0ec0560..aa97a07 100644
--- a/arch/x86/include/asm/pgtable.h
+++ b/arch/x86/include/asm/pgtable.h
@@ -131,8 +131,13 @@
static inline int pte_special(pte_t pte)
{
- return (pte_flags(pte) & (_PAGE_PRESENT|_PAGE_SPECIAL)) ==
- (_PAGE_PRESENT|_PAGE_SPECIAL);
+ /*
+ * See CONFIG_NUMA_BALANCING pte_numa in include/asm-generic/pgtable.h.
+ * On x86 we have _PAGE_BIT_NUMA == _PAGE_BIT_GLOBAL+1 ==
+ * __PAGE_BIT_SOFTW1 == _PAGE_BIT_SPECIAL.
+ */
+ return (pte_flags(pte) & _PAGE_SPECIAL) &&
+ (pte_flags(pte) & (_PAGE_PRESENT|_PAGE_PROTNONE));
}
static inline unsigned long pte_pfn(pte_t pte)
diff --git a/arch/x86/kernel/Makefile b/arch/x86/kernel/Makefile
index b5ea75c..ada2e2d 100644
--- a/arch/x86/kernel/Makefile
+++ b/arch/x86/kernel/Makefile
@@ -71,6 +71,7 @@
obj-$(CONFIG_X86_TSC) += trace_clock.o
obj-$(CONFIG_KEXEC) += machine_kexec_$(BITS).o
obj-$(CONFIG_KEXEC) += relocate_kernel_$(BITS).o crash.o
+obj-$(CONFIG_KEXEC_FILE) += kexec-bzimage64.o
obj-$(CONFIG_CRASH_DUMP) += crash_dump_$(BITS).o
obj-y += kprobes/
obj-$(CONFIG_MODULES) += module.o
@@ -118,5 +119,4 @@
obj-$(CONFIG_PCI_MMCONFIG) += mmconf-fam10h_64.o
obj-y += vsmp_64.o
- obj-$(CONFIG_KEXEC) += kexec-bzimage64.o
endif
diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c
index 29290f5..337ce5a 100644
--- a/arch/x86/kernel/apic/io_apic.c
+++ b/arch/x86/kernel/apic/io_apic.c
@@ -1070,6 +1070,11 @@
}
if (flags & IOAPIC_MAP_ALLOC) {
+ /* special handling for legacy IRQs */
+ if (irq < nr_legacy_irqs() && info->count == 1 &&
+ mp_irqdomain_map(domain, irq, pin) != 0)
+ irq = -1;
+
if (irq > 0)
info->count++;
else if (info->count == 0)
@@ -3896,7 +3901,15 @@
info->polarity = 1;
}
info->node = NUMA_NO_NODE;
- info->set = 1;
+
+ /*
+ * setup_IO_APIC_irqs() programs all legacy IRQs with default
+ * trigger and polarity attributes. Don't set the flag for that
+ * case so the first legacy IRQ user could reprogram the pin
+ * with real trigger and polarity attributes.
+ */
+ if (virq >= nr_legacy_irqs() || info->count)
+ info->set = 1;
}
set_io_apic_irq_attr(&attr, ioapic, hwirq, info->trigger,
info->polarity);
@@ -3946,6 +3959,18 @@
return ret;
}
+bool mp_should_keep_irq(struct device *dev)
+{
+ if (dev->power.is_prepared)
+ return true;
+#ifdef CONFIG_PM_RUNTIME
+ if (dev->power.runtime_status == RPM_SUSPENDING)
+ return true;
+#endif
+
+ return false;
+}
+
/* Enable IOAPIC early just for system timer */
void __init pre_init_apic_IRQ0(void)
{
diff --git a/arch/x86/kernel/crash.c b/arch/x86/kernel/crash.c
index 0553a34..a618fcd 100644
--- a/arch/x86/kernel/crash.c
+++ b/arch/x86/kernel/crash.c
@@ -182,8 +182,7 @@
crash_save_cpu(regs, safe_smp_processor_id());
}
-#ifdef CONFIG_X86_64
-
+#ifdef CONFIG_KEXEC_FILE
static int get_nr_ram_ranges_callback(unsigned long start_pfn,
unsigned long nr_pfn, void *arg)
{
@@ -696,5 +695,4 @@
return ret;
}
-
-#endif /* CONFIG_X86_64 */
+#endif /* CONFIG_KEXEC_FILE */
diff --git a/arch/x86/kernel/irqinit.c b/arch/x86/kernel/irqinit.c
index 1e6cff5..44f1ed4 100644
--- a/arch/x86/kernel/irqinit.c
+++ b/arch/x86/kernel/irqinit.c
@@ -203,7 +203,7 @@
set_intr_gate(i, interrupt[i - FIRST_EXTERNAL_VECTOR]);
}
- if (!acpi_ioapic && !of_ioapic)
+ if (!acpi_ioapic && !of_ioapic && nr_legacy_irqs())
setup_irq(2, &irq2);
#ifdef CONFIG_X86_32
diff --git a/arch/x86/kernel/machine_kexec_64.c b/arch/x86/kernel/machine_kexec_64.c
index 8b04018..4859810 100644
--- a/arch/x86/kernel/machine_kexec_64.c
+++ b/arch/x86/kernel/machine_kexec_64.c
@@ -25,9 +25,11 @@
#include <asm/debugreg.h>
#include <asm/kexec-bzimage64.h>
+#ifdef CONFIG_KEXEC_FILE
static struct kexec_file_ops *kexec_file_loaders[] = {
&kexec_bzImage64_ops,
};
+#endif
static void free_transition_pgtable(struct kimage *image)
{
@@ -178,6 +180,7 @@
);
}
+#ifdef CONFIG_KEXEC_FILE
/* Update purgatory as needed after various image segments have been prepared */
static int arch_update_purgatory(struct kimage *image)
{
@@ -209,6 +212,12 @@
return ret;
}
+#else /* !CONFIG_KEXEC_FILE */
+static inline int arch_update_purgatory(struct kimage *image)
+{
+ return 0;
+}
+#endif /* CONFIG_KEXEC_FILE */
int machine_kexec_prepare(struct kimage *image)
{
@@ -329,6 +338,7 @@
/* arch-dependent functionality related to kexec file-based syscall */
+#ifdef CONFIG_KEXEC_FILE
int arch_kexec_kernel_image_probe(struct kimage *image, void *buf,
unsigned long buf_len)
{
@@ -522,3 +532,4 @@
(int)ELF64_R_TYPE(rel[i].r_info), value);
return -ENOEXEC;
}
+#endif /* CONFIG_KEXEC_FILE */
diff --git a/arch/x86/kernel/time.c b/arch/x86/kernel/time.c
index bf7ef5c..0fa2960 100644
--- a/arch/x86/kernel/time.c
+++ b/arch/x86/kernel/time.c
@@ -68,6 +68,8 @@
void __init setup_default_timer_irq(void)
{
+ if (!nr_legacy_irqs())
+ return;
setup_irq(0, &irq0);
}
diff --git a/arch/x86/pci/intel_mid_pci.c b/arch/x86/pci/intel_mid_pci.c
index 3865116..b9958c3 100644
--- a/arch/x86/pci/intel_mid_pci.c
+++ b/arch/x86/pci/intel_mid_pci.c
@@ -229,7 +229,7 @@
static void intel_mid_pci_irq_disable(struct pci_dev *dev)
{
- if (!dev->dev.power.is_prepared && dev->irq > 0)
+ if (!mp_should_keep_irq(&dev->dev) && dev->irq > 0)
mp_unmap_irq(dev->irq);
}
diff --git a/arch/x86/pci/irq.c b/arch/x86/pci/irq.c
index bc1a2c3..eb500c2 100644
--- a/arch/x86/pci/irq.c
+++ b/arch/x86/pci/irq.c
@@ -1256,7 +1256,7 @@
static void pirq_disable_irq(struct pci_dev *dev)
{
- if (io_apic_assign_pci_irqs && !dev->dev.power.is_prepared &&
+ if (io_apic_assign_pci_irqs && !mp_should_keep_irq(&dev->dev) &&
dev->irq) {
mp_unmap_irq(dev->irq);
dev->irq = 0;
diff --git a/arch/x86/purgatory/Makefile b/arch/x86/purgatory/Makefile
index 7fde9ee..899dd24 100644
--- a/arch/x86/purgatory/Makefile
+++ b/arch/x86/purgatory/Makefile
@@ -11,6 +11,7 @@
# sure how to relocate those. Like kexec-tools, use custom flags.
KBUILD_CFLAGS := -fno-strict-aliasing -Wall -Wstrict-prototypes -fno-zero-initialized-in-bss -fno-builtin -ffreestanding -c -MD -Os -mcmodel=large
+KBUILD_CFLAGS += -m$(BITS)
$(obj)/purgatory.ro: $(PURGATORY_OBJS) FORCE
$(call if_changed,ld)
@@ -24,7 +25,4 @@
$(call if_changed,bin2c)
-# No loaders for 32bits yet.
-ifeq ($(CONFIG_X86_64),y)
- obj-$(CONFIG_KEXEC) += kexec-purgatory.o
-endif
+obj-$(CONFIG_KEXEC_FILE) += kexec-purgatory.o
diff --git a/arch/xtensa/kernel/smp.c b/arch/xtensa/kernel/smp.c
index 40b5a37..4d02e38 100644
--- a/arch/xtensa/kernel/smp.c
+++ b/arch/xtensa/kernel/smp.c
@@ -571,6 +571,7 @@
};
on_each_cpu(ipi_flush_icache_range, &fd, 1);
}
+EXPORT_SYMBOL(flush_icache_range);
/* ------------------------------------------------------------------------- */
diff --git a/block/bio-integrity.c b/block/bio-integrity.c
index bc423f7b..f14b4ab 100644
--- a/block/bio-integrity.c
+++ b/block/bio-integrity.c
@@ -520,7 +520,7 @@
*/
if (error) {
bio->bi_end_io = bip->bip_end_io;
- bio_endio(bio, error);
+ bio_endio_nodec(bio, error);
return;
}
diff --git a/block/blk-core.c b/block/blk-core.c
index c359d72..bf930f4 100644
--- a/block/blk-core.c
+++ b/block/blk-core.c
@@ -1252,7 +1252,6 @@
rq->__sector = (sector_t) -1;
rq->bio = rq->biotail = NULL;
memset(rq->__cmd, 0, sizeof(rq->__cmd));
- rq->cmd = rq->__cmd;
}
EXPORT_SYMBOL(blk_rq_set_block_pc);
diff --git a/block/blk-mq.c b/block/blk-mq.c
index 5189cb1..4aac826 100644
--- a/block/blk-mq.c
+++ b/block/blk-mq.c
@@ -112,18 +112,22 @@
*/
void blk_mq_freeze_queue(struct request_queue *q)
{
+ bool freeze;
+
spin_lock_irq(q->queue_lock);
- q->mq_freeze_depth++;
+ freeze = !q->mq_freeze_depth++;
spin_unlock_irq(q->queue_lock);
- percpu_ref_kill(&q->mq_usage_counter);
- blk_mq_run_queues(q, false);
+ if (freeze) {
+ percpu_ref_kill(&q->mq_usage_counter);
+ blk_mq_run_queues(q, false);
+ }
wait_event(q->mq_freeze_wq, percpu_ref_is_zero(&q->mq_usage_counter));
}
static void blk_mq_unfreeze_queue(struct request_queue *q)
{
- bool wake = false;
+ bool wake;
spin_lock_irq(q->queue_lock);
wake = !--q->mq_freeze_depth;
@@ -172,6 +176,8 @@
/* tag was already set */
rq->errors = 0;
+ rq->cmd = rq->__cmd;
+
rq->extra_len = 0;
rq->sense_len = 0;
rq->resid_len = 0;
@@ -1068,13 +1074,17 @@
blk_account_io_start(rq, 1);
}
+static inline bool hctx_allow_merges(struct blk_mq_hw_ctx *hctx)
+{
+ return (hctx->flags & BLK_MQ_F_SHOULD_MERGE) &&
+ !blk_queue_nomerges(hctx->queue);
+}
+
static inline bool blk_mq_merge_queue_io(struct blk_mq_hw_ctx *hctx,
struct blk_mq_ctx *ctx,
struct request *rq, struct bio *bio)
{
- struct request_queue *q = hctx->queue;
-
- if (!(hctx->flags & BLK_MQ_F_SHOULD_MERGE)) {
+ if (!hctx_allow_merges(hctx)) {
blk_mq_bio_to_request(rq, bio);
spin_lock(&ctx->lock);
insert_rq:
@@ -1082,6 +1092,8 @@
spin_unlock(&ctx->lock);
return false;
} else {
+ struct request_queue *q = hctx->queue;
+
spin_lock(&ctx->lock);
if (!blk_mq_attempt_merge(q, ctx, bio)) {
blk_mq_bio_to_request(rq, bio);
@@ -1574,7 +1586,7 @@
hctx->tags = set->tags[i];
/*
- * Allocate space for all possible cpus to avoid allocation in
+ * Allocate space for all possible cpus to avoid allocation at
* runtime
*/
hctx->ctxs = kmalloc_node(nr_cpu_ids * sizeof(void *),
@@ -1662,8 +1674,8 @@
queue_for_each_hw_ctx(q, hctx, i) {
/*
- * If not software queues are mapped to this hardware queue,
- * disable it and free the request entries
+ * If no software queues are mapped to this hardware queue,
+ * disable it and free the request entries.
*/
if (!hctx->nr_ctx) {
struct blk_mq_tag_set *set = q->tag_set;
@@ -1713,14 +1725,10 @@
{
struct blk_mq_tag_set *set = q->tag_set;
- blk_mq_freeze_queue(q);
-
mutex_lock(&set->tag_list_lock);
list_del_init(&q->tag_set_list);
blk_mq_update_tag_set_depth(set);
mutex_unlock(&set->tag_list_lock);
-
- blk_mq_unfreeze_queue(q);
}
static void blk_mq_add_queue_tag_set(struct blk_mq_tag_set *set,
diff --git a/block/cfq-iosched.c b/block/cfq-iosched.c
index cadc378..3f31cf9 100644
--- a/block/cfq-iosched.c
+++ b/block/cfq-iosched.c
@@ -1272,15 +1272,22 @@
rb_insert_color(&cfqg->rb_node, &st->rb);
}
+/*
+ * This has to be called only on activation of cfqg
+ */
static void
cfq_update_group_weight(struct cfq_group *cfqg)
{
- BUG_ON(!RB_EMPTY_NODE(&cfqg->rb_node));
-
if (cfqg->new_weight) {
cfqg->weight = cfqg->new_weight;
cfqg->new_weight = 0;
}
+}
+
+static void
+cfq_update_group_leaf_weight(struct cfq_group *cfqg)
+{
+ BUG_ON(!RB_EMPTY_NODE(&cfqg->rb_node));
if (cfqg->new_leaf_weight) {
cfqg->leaf_weight = cfqg->new_leaf_weight;
@@ -1299,7 +1306,12 @@
/* add to the service tree */
BUG_ON(!RB_EMPTY_NODE(&cfqg->rb_node));
- cfq_update_group_weight(cfqg);
+ /*
+ * Update leaf_weight. We cannot update weight at this point
+ * because cfqg might already have been activated and is
+ * contributing its current weight to the parent's child_weight.
+ */
+ cfq_update_group_leaf_weight(cfqg);
__cfq_group_service_tree_add(st, cfqg);
/*
@@ -1323,6 +1335,7 @@
*/
while ((parent = cfqg_parent(pos))) {
if (propagate) {
+ cfq_update_group_weight(pos);
propagate = !parent->nr_active++;
parent->children_weight += pos->weight;
}
diff --git a/block/scsi_ioctl.c b/block/scsi_ioctl.c
index 51bf515..9b8eaec 100644
--- a/block/scsi_ioctl.c
+++ b/block/scsi_ioctl.c
@@ -279,7 +279,6 @@
r = blk_rq_unmap_user(bio);
if (!ret)
ret = r;
- blk_put_request(rq);
return ret;
}
@@ -297,8 +296,6 @@
if (hdr->interface_id != 'S')
return -EINVAL;
- if (hdr->cmd_len > BLK_MAX_CDB)
- return -EINVAL;
if (hdr->dxfer_len > (queue_max_hw_sectors(q) << 9))
return -EIO;
@@ -317,16 +314,23 @@
if (hdr->flags & SG_FLAG_Q_AT_HEAD)
at_head = 1;
+ ret = -ENOMEM;
rq = blk_get_request(q, writing ? WRITE : READ, GFP_KERNEL);
if (!rq)
- return -ENOMEM;
+ goto out;
blk_rq_set_block_pc(rq);
- if (blk_fill_sghdr_rq(q, rq, hdr, mode)) {
- blk_put_request(rq);
- return -EFAULT;
+ if (hdr->cmd_len > BLK_MAX_CDB) {
+ rq->cmd = kzalloc(hdr->cmd_len, GFP_KERNEL);
+ if (!rq->cmd)
+ goto out_put_request;
}
+ ret = -EFAULT;
+ if (blk_fill_sghdr_rq(q, rq, hdr, mode))
+ goto out_free_cdb;
+
+ ret = 0;
if (hdr->iovec_count) {
size_t iov_data_len;
struct iovec *iov = NULL;
@@ -335,7 +339,7 @@
0, NULL, &iov);
if (ret < 0) {
kfree(iov);
- goto out;
+ goto out_free_cdb;
}
iov_data_len = ret;
@@ -358,7 +362,7 @@
GFP_KERNEL);
if (ret)
- goto out;
+ goto out_free_cdb;
bio = rq->bio;
memset(sense, 0, sizeof(sense));
@@ -376,9 +380,14 @@
hdr->duration = jiffies_to_msecs(jiffies - start_time);
- return blk_complete_sghdr_rq(rq, hdr, bio);
-out:
+ ret = blk_complete_sghdr_rq(rq, hdr, bio);
+
+out_free_cdb:
+ if (rq->cmd != rq->__cmd)
+ kfree(rq->cmd);
+out_put_request:
blk_put_request(rq);
+out:
return ret;
}
@@ -448,6 +457,11 @@
}
rq = blk_get_request(q, in_len ? WRITE : READ, __GFP_WAIT);
+ if (!rq) {
+ err = -ENOMEM;
+ goto error;
+ }
+ blk_rq_set_block_pc(rq);
cmdlen = COMMAND_SIZE(opcode);
@@ -501,7 +515,6 @@
memset(sense, 0, sizeof(sense));
rq->sense = sense;
rq->sense_len = 0;
- blk_rq_set_block_pc(rq);
blk_execute_rq(q, disk, rq, 0);
@@ -521,7 +534,8 @@
error:
kfree(buffer);
- blk_put_request(rq);
+ if (rq)
+ blk_put_request(rq);
return err;
}
EXPORT_SYMBOL_GPL(sg_scsi_ioctl);
diff --git a/drivers/acpi/acpi_lpss.c b/drivers/acpi/acpi_lpss.c
index ce06149..9dfec48 100644
--- a/drivers/acpi/acpi_lpss.c
+++ b/drivers/acpi/acpi_lpss.c
@@ -196,6 +196,17 @@
.setup = lpss_i2c_setup,
};
+static struct lpss_shared_clock bsw_pwm_clock = {
+ .name = "pwm_clk",
+ .rate = 19200000,
+};
+
+static struct lpss_device_desc bsw_pwm_dev_desc = {
+ .clk_required = true,
+ .save_ctx = true,
+ .shared_clock = &bsw_pwm_clock,
+};
+
#else
#define LPSS_ADDR(desc) (0UL)
@@ -225,6 +236,12 @@
{ "INT33B2", },
{ "INT33FC", },
+ /* Braswell LPSS devices */
+ { "80862288", LPSS_ADDR(bsw_pwm_dev_desc) },
+ { "8086228A", LPSS_ADDR(byt_uart_dev_desc) },
+ { "8086228E", LPSS_ADDR(byt_spi_dev_desc) },
+ { "808622C1", LPSS_ADDR(byt_i2c_dev_desc) },
+
{ "INT3430", LPSS_ADDR(lpt_dev_desc) },
{ "INT3431", LPSS_ADDR(lpt_dev_desc) },
{ "INT3432", LPSS_ADDR(lpt_i2c_dev_desc) },
diff --git a/drivers/acpi/ec.c b/drivers/acpi/ec.c
index a66ab65..9922cc4 100644
--- a/drivers/acpi/ec.c
+++ b/drivers/acpi/ec.c
@@ -197,6 +197,8 @@
t->rdata[t->ri++] = acpi_ec_read_data(ec);
if (t->rlen == t->ri) {
t->flags |= ACPI_EC_COMMAND_COMPLETE;
+ if (t->command == ACPI_EC_COMMAND_QUERY)
+ pr_debug("hardware QR_EC completion\n");
wakeup = true;
}
} else
@@ -208,7 +210,20 @@
}
return wakeup;
} else {
- if ((status & ACPI_EC_FLAG_IBF) == 0) {
+ /*
+ * There is firmware refusing to respond QR_EC when SCI_EVT
+ * is not set, for which case, we complete the QR_EC
+ * without issuing it to the firmware.
+ * https://bugzilla.kernel.org/show_bug.cgi?id=86211
+ */
+ if (!(status & ACPI_EC_FLAG_SCI) &&
+ (t->command == ACPI_EC_COMMAND_QUERY)) {
+ t->flags |= ACPI_EC_COMMAND_POLL;
+ t->rdata[t->ri++] = 0x00;
+ t->flags |= ACPI_EC_COMMAND_COMPLETE;
+ pr_debug("software QR_EC completion\n");
+ wakeup = true;
+ } else if ((status & ACPI_EC_FLAG_IBF) == 0) {
acpi_ec_write_cmd(ec, t->command);
t->flags |= ACPI_EC_COMMAND_POLL;
} else
@@ -288,11 +303,11 @@
/* following two actions should be kept atomic */
ec->curr = t;
start_transaction(ec);
- if (ec->curr->command == ACPI_EC_COMMAND_QUERY)
- clear_bit(EC_FLAGS_QUERY_PENDING, &ec->flags);
spin_unlock_irqrestore(&ec->lock, tmp);
ret = ec_poll(ec);
spin_lock_irqsave(&ec->lock, tmp);
+ if (ec->curr->command == ACPI_EC_COMMAND_QUERY)
+ clear_bit(EC_FLAGS_QUERY_PENDING, &ec->flags);
ec->curr = NULL;
spin_unlock_irqrestore(&ec->lock, tmp);
return ret;
diff --git a/drivers/acpi/pci_irq.c b/drivers/acpi/pci_irq.c
index c96887d..6e6b80e 100644
--- a/drivers/acpi/pci_irq.c
+++ b/drivers/acpi/pci_irq.c
@@ -484,6 +484,10 @@
/* Keep IOAPIC pin configuration when suspending */
if (dev->dev.power.is_prepared)
return;
+#ifdef CONFIG_PM_RUNTIME
+ if (dev->dev.power.runtime_status == RPM_SUSPENDING)
+ return;
+#endif
entry = acpi_pci_irq_lookup(dev, pin);
if (!entry)
diff --git a/drivers/acpi/scan.c b/drivers/acpi/scan.c
index 0a817ad..9a92989 100644
--- a/drivers/acpi/scan.c
+++ b/drivers/acpi/scan.c
@@ -922,12 +922,17 @@
device->driver->ops.notify(device, event);
}
-static acpi_status acpi_device_notify_fixed(void *data)
+static void acpi_device_notify_fixed(void *data)
{
struct acpi_device *device = data;
/* Fixed hardware devices have no handles */
acpi_device_notify(NULL, ACPI_FIXED_HARDWARE_EVENT, device);
+}
+
+static acpi_status acpi_device_fixed_event(void *data)
+{
+ acpi_os_execute(OSL_NOTIFY_HANDLER, acpi_device_notify_fixed, data);
return AE_OK;
}
@@ -938,12 +943,12 @@
if (device->device_type == ACPI_BUS_TYPE_POWER_BUTTON)
status =
acpi_install_fixed_event_handler(ACPI_EVENT_POWER_BUTTON,
- acpi_device_notify_fixed,
+ acpi_device_fixed_event,
device);
else if (device->device_type == ACPI_BUS_TYPE_SLEEP_BUTTON)
status =
acpi_install_fixed_event_handler(ACPI_EVENT_SLEEP_BUTTON,
- acpi_device_notify_fixed,
+ acpi_device_fixed_event,
device);
else
status = acpi_install_notify_handler(device->handle,
@@ -960,10 +965,10 @@
{
if (device->device_type == ACPI_BUS_TYPE_POWER_BUTTON)
acpi_remove_fixed_event_handler(ACPI_EVENT_POWER_BUTTON,
- acpi_device_notify_fixed);
+ acpi_device_fixed_event);
else if (device->device_type == ACPI_BUS_TYPE_SLEEP_BUTTON)
acpi_remove_fixed_event_handler(ACPI_EVENT_SLEEP_BUTTON,
- acpi_device_notify_fixed);
+ acpi_device_fixed_event);
else
acpi_remove_notify_handler(device->handle, ACPI_DEVICE_NOTIFY,
acpi_device_notify);
@@ -975,7 +980,7 @@
struct acpi_driver *acpi_drv = to_acpi_driver(dev->driver);
int ret;
- if (acpi_dev->handler)
+ if (acpi_dev->handler && !acpi_is_pnp_device(acpi_dev))
return -EINVAL;
if (!acpi_drv->ops.add)
diff --git a/drivers/block/brd.c b/drivers/block/brd.c
index c7d138e..3598110 100644
--- a/drivers/block/brd.c
+++ b/drivers/block/brd.c
@@ -442,12 +442,15 @@
int rd_size = CONFIG_BLK_DEV_RAM_SIZE;
static int max_part;
static int part_shift;
+static int part_show = 0;
module_param(rd_nr, int, S_IRUGO);
MODULE_PARM_DESC(rd_nr, "Maximum number of brd devices");
module_param(rd_size, int, S_IRUGO);
MODULE_PARM_DESC(rd_size, "Size of each RAM disk in kbytes.");
module_param(max_part, int, S_IRUGO);
MODULE_PARM_DESC(max_part, "Maximum number of partitions per RAM disk");
+module_param(part_show, int, S_IRUGO);
+MODULE_PARM_DESC(part_show, "Control RAM disk visibility in /proc/partitions");
MODULE_LICENSE("GPL");
MODULE_ALIAS_BLOCKDEV_MAJOR(RAMDISK_MAJOR);
MODULE_ALIAS("rd");
@@ -501,7 +504,8 @@
disk->fops = &brd_fops;
disk->private_data = brd;
disk->queue = brd->brd_queue;
- disk->flags |= GENHD_FL_SUPPRESS_PARTITION_INFO;
+ if (!part_show)
+ disk->flags |= GENHD_FL_SUPPRESS_PARTITION_INFO;
sprintf(disk->disk_name, "ram%d", i);
set_capacity(disk, rd_size * 2);
diff --git a/drivers/block/xsysace.c b/drivers/block/xsysace.c
index ab3ea62..c4328d9 100644
--- a/drivers/block/xsysace.c
+++ b/drivers/block/xsysace.c
@@ -1203,7 +1203,6 @@
.probe = ace_probe,
.remove = ace_remove,
.driver = {
- .owner = THIS_MODULE,
.name = "xsysace",
.of_match_table = ace_of_match,
},
diff --git a/drivers/block/zram/zram_drv.c b/drivers/block/zram/zram_drv.c
index dfa4024..d00831c 100644
--- a/drivers/block/zram/zram_drv.c
+++ b/drivers/block/zram/zram_drv.c
@@ -378,7 +378,6 @@
/* Should NEVER happen. Return bio error if it does. */
if (unlikely(ret)) {
pr_err("Decompression failed! err=%d, page=%u\n", ret, index);
- atomic64_inc(&zram->stats.failed_reads);
return ret;
}
@@ -547,8 +546,6 @@
zcomp_strm_release(zram->comp, zstrm);
if (is_partial_io(bvec))
kfree(uncmem);
- if (ret)
- atomic64_inc(&zram->stats.failed_writes);
return ret;
}
@@ -566,6 +563,13 @@
ret = zram_bvec_write(zram, bvec, index, offset);
}
+ if (unlikely(ret)) {
+ if (rw == READ)
+ atomic64_inc(&zram->stats.failed_reads);
+ else
+ atomic64_inc(&zram->stats.failed_writes);
+ }
+
return ret;
}
diff --git a/drivers/block/zram/zram_drv.h b/drivers/block/zram/zram_drv.h
index 5b0afde..e0f725c 100644
--- a/drivers/block/zram/zram_drv.h
+++ b/drivers/block/zram/zram_drv.h
@@ -84,7 +84,7 @@
atomic64_t compr_data_size; /* compressed size of pages stored */
atomic64_t num_reads; /* failed + successful */
atomic64_t num_writes; /* --do-- */
- atomic64_t failed_reads; /* should NEVER! happen */
+ atomic64_t failed_reads; /* can happen when memory is too low */
atomic64_t failed_writes; /* can happen when memory is too low */
atomic64_t invalid_io; /* non-page-aligned I/O requests */
atomic64_t notify_free; /* no. of swap slot free notifications */
diff --git a/drivers/cpufreq/intel_pstate.c b/drivers/cpufreq/intel_pstate.c
index c5eac94..e396ad3 100644
--- a/drivers/cpufreq/intel_pstate.c
+++ b/drivers/cpufreq/intel_pstate.c
@@ -660,6 +660,7 @@
ICPU(0x3f, core_params),
ICPU(0x45, core_params),
ICPU(0x46, core_params),
+ ICPU(0x4c, byt_params),
ICPU(0x4f, core_params),
ICPU(0x56, core_params),
{}
@@ -688,7 +689,7 @@
add_timer_on(&cpu->timer, cpunum);
- pr_info("Intel pstate controlling: cpu %d\n", cpunum);
+ pr_debug("Intel pstate controlling: cpu %d\n", cpunum);
return 0;
}
diff --git a/drivers/cpufreq/s5pv210-cpufreq.c b/drivers/cpufreq/s5pv210-cpufreq.c
index 9a68225..3f9791f 100644
--- a/drivers/cpufreq/s5pv210-cpufreq.c
+++ b/drivers/cpufreq/s5pv210-cpufreq.c
@@ -501,7 +501,7 @@
return val >> 8;
}
-static int __init s5pv210_cpu_init(struct cpufreq_policy *policy)
+static int s5pv210_cpu_init(struct cpufreq_policy *policy)
{
unsigned long mem_type;
int ret;
diff --git a/drivers/dma-buf/fence.c b/drivers/dma-buf/fence.c
index 4222cb2..7bb9d65 100644
--- a/drivers/dma-buf/fence.c
+++ b/drivers/dma-buf/fence.c
@@ -29,7 +29,7 @@
EXPORT_TRACEPOINT_SYMBOL(fence_annotate_wait_on);
EXPORT_TRACEPOINT_SYMBOL(fence_emit);
-/**
+/*
* fence context counter: each execution context should have its own
* fence context, this allows checking if fences belong to the same
* context or not. One device can have multiple separate contexts,
diff --git a/drivers/gpu/drm/ast/ast_tables.h b/drivers/gpu/drm/ast/ast_tables.h
index 4c761dc..05c01ea 100644
--- a/drivers/gpu/drm/ast/ast_tables.h
+++ b/drivers/gpu/drm/ast/ast_tables.h
@@ -99,6 +99,7 @@
{0x25, 0x65, 0x80}, /* 16: VCLK88.75 */
{0x77, 0x58, 0x80}, /* 17: VCLK119 */
{0x32, 0x67, 0x80}, /* 18: VCLK85_5 */
+ {0x6a, 0x6d, 0x80}, /* 19: VCLK97_75 */
};
static struct ast_vbios_stdtable vbios_stdtable[] = {
diff --git a/drivers/gpu/drm/drm_crtc.c b/drivers/gpu/drm/drm_crtc.c
index fa2be24..90e7730 100644
--- a/drivers/gpu/drm/drm_crtc.c
+++ b/drivers/gpu/drm/drm_crtc.c
@@ -4696,8 +4696,9 @@
return -EINVAL;
/* overflow checks for 32bit size calculations */
+ /* NOTE: DIV_ROUND_UP() can overflow */
cpp = DIV_ROUND_UP(args->bpp, 8);
- if (cpp > 0xffffffffU / args->width)
+ if (!cpp || cpp > 0xffffffffU / args->width)
return -EINVAL;
stride = cpp * args->width;
if (args->height > 0xffffffffU / stride)
diff --git a/drivers/gpu/drm/msm/mdp/mdp4/mdp4_crtc.c b/drivers/gpu/drm/msm/mdp/mdp4/mdp4_crtc.c
index 74cebb5..c6c80ea2 100644
--- a/drivers/gpu/drm/msm/mdp/mdp4/mdp4_crtc.c
+++ b/drivers/gpu/drm/msm/mdp/mdp4/mdp4_crtc.c
@@ -397,6 +397,7 @@
struct mdp4_crtc *mdp4_crtc = to_mdp4_crtc(crtc);
DBG("%s", mdp4_crtc->name);
/* make sure we hold a ref to mdp clks while setting up mode: */
+ drm_crtc_vblank_get(crtc);
mdp4_enable(get_kms(crtc));
mdp4_crtc_dpms(crtc, DRM_MODE_DPMS_OFF);
}
@@ -407,6 +408,7 @@
crtc_flush(crtc);
/* drop the ref to mdp clk's that we got in prepare: */
mdp4_disable(get_kms(crtc));
+ drm_crtc_vblank_put(crtc);
}
static int mdp4_crtc_mode_set_base(struct drm_crtc *crtc, int x, int y,
diff --git a/drivers/gpu/drm/msm/msm_drv.c b/drivers/gpu/drm/msm/msm_drv.c
index b447c01..26ee80d 100644
--- a/drivers/gpu/drm/msm/msm_drv.c
+++ b/drivers/gpu/drm/msm/msm_drv.c
@@ -974,12 +974,11 @@
for (i = 0; i < ARRAY_SIZE(devnames); i++) {
struct device *dev;
- int ret;
dev = bus_find_device_by_name(&platform_bus_type,
NULL, devnames[i]);
if (!dev) {
- dev_info(master, "still waiting for %s\n", devnames[i]);
+ dev_info(&pdev->dev, "still waiting for %s\n", devnames[i]);
return -EPROBE_DEFER;
}
diff --git a/drivers/gpu/drm/msm/msm_fbdev.c b/drivers/gpu/drm/msm/msm_fbdev.c
index 9c5221c..ab5bfd2 100644
--- a/drivers/gpu/drm/msm/msm_fbdev.c
+++ b/drivers/gpu/drm/msm/msm_fbdev.c
@@ -143,7 +143,7 @@
ret = msm_gem_get_iova_locked(fbdev->bo, 0, &paddr);
if (ret) {
dev_err(dev->dev, "failed to get buffer obj iova: %d\n", ret);
- goto fail;
+ goto fail_unlock;
}
fbi = framebuffer_alloc(0, dev->dev);
diff --git a/drivers/gpu/drm/msm/msm_iommu.c b/drivers/gpu/drm/msm/msm_iommu.c
index 099af48..7acdaa5 100644
--- a/drivers/gpu/drm/msm/msm_iommu.c
+++ b/drivers/gpu/drm/msm/msm_iommu.c
@@ -27,8 +27,8 @@
static int msm_fault_handler(struct iommu_domain *iommu, struct device *dev,
unsigned long iova, int flags, void *arg)
{
- DBG("*** fault: iova=%08lx, flags=%d", iova, flags);
- return -ENOSYS;
+ pr_warn_ratelimited("*** fault: iova=%08lx, flags=%d\n", iova, flags);
+ return 0;
}
static int msm_iommu_attach(struct msm_mmu *mmu, const char **names, int cnt)
diff --git a/drivers/gpu/drm/radeon/cik.c b/drivers/gpu/drm/radeon/cik.c
index 79a5a55..fa95659 100644
--- a/drivers/gpu/drm/radeon/cik.c
+++ b/drivers/gpu/drm/radeon/cik.c
@@ -5749,20 +5749,17 @@
WREG32(0x15D8, 0);
WREG32(0x15DC, 0);
- /* empty context1-15 */
- /* FIXME start with 4G, once using 2 level pt switch to full
- * vm size space
- */
+ /* restore context1-15 */
/* set vm size, must be a multiple of 4 */
WREG32(VM_CONTEXT1_PAGE_TABLE_START_ADDR, 0);
WREG32(VM_CONTEXT1_PAGE_TABLE_END_ADDR, rdev->vm_manager.max_pfn);
for (i = 1; i < 16; i++) {
if (i < 8)
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2),
- rdev->gart.table_addr >> 12);
+ rdev->vm_manager.saved_table_addr[i]);
else
WREG32(VM_CONTEXT8_PAGE_TABLE_BASE_ADDR + ((i - 8) << 2),
- rdev->gart.table_addr >> 12);
+ rdev->vm_manager.saved_table_addr[i]);
}
/* enable context1-15 */
@@ -5827,6 +5824,17 @@
*/
static void cik_pcie_gart_disable(struct radeon_device *rdev)
{
+ unsigned i;
+
+ for (i = 1; i < 16; ++i) {
+ uint32_t reg;
+ if (i < 8)
+ reg = VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2);
+ else
+ reg = VM_CONTEXT8_PAGE_TABLE_BASE_ADDR + ((i - 8) << 2);
+ rdev->vm_manager.saved_table_addr[i] = RREG32(reg);
+ }
+
/* Disable all tables */
WREG32(VM_CONTEXT0_CNTL, 0);
WREG32(VM_CONTEXT1_CNTL, 0);
@@ -9555,6 +9563,9 @@
int ret, i;
u16 tmp16;
+ if (pci_is_root_bus(rdev->pdev->bus))
+ return;
+
if (radeon_pcie_gen2 == 0)
return;
@@ -9781,7 +9792,8 @@
if (orig != data)
WREG32_PCIE_PORT(PCIE_LC_LINK_WIDTH_CNTL, data);
- if (!disable_clkreq) {
+ if (!disable_clkreq &&
+ !pci_is_root_bus(rdev->pdev->bus)) {
struct pci_dev *root = rdev->pdev->bus->self;
u32 lnkcap;
diff --git a/drivers/gpu/drm/radeon/ni.c b/drivers/gpu/drm/radeon/ni.c
index ba89375..3faee58 100644
--- a/drivers/gpu/drm/radeon/ni.c
+++ b/drivers/gpu/drm/radeon/ni.c
@@ -1271,7 +1271,7 @@
WREG32(VM_CONTEXT0_PAGE_TABLE_START_ADDR + (i << 2), 0);
WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR + (i << 2), rdev->vm_manager.max_pfn);
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2),
- rdev->gart.table_addr >> 12);
+ rdev->vm_manager.saved_table_addr[i]);
}
/* enable context1-7 */
@@ -1303,6 +1303,13 @@
static void cayman_pcie_gart_disable(struct radeon_device *rdev)
{
+ unsigned i;
+
+ for (i = 1; i < 8; ++i) {
+ rdev->vm_manager.saved_table_addr[i] = RREG32(
+ VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2));
+ }
+
/* Disable all tables */
WREG32(VM_CONTEXT0_CNTL, 0);
WREG32(VM_CONTEXT1_CNTL, 0);
diff --git a/drivers/gpu/drm/radeon/r600.c b/drivers/gpu/drm/radeon/r600.c
index e8bf0ea..e616eb5 100644
--- a/drivers/gpu/drm/radeon/r600.c
+++ b/drivers/gpu/drm/radeon/r600.c
@@ -1812,7 +1812,6 @@
{
u32 tiling_config;
u32 ramcfg;
- u32 cc_rb_backend_disable;
u32 cc_gc_shader_pipe_config;
u32 tmp;
int i, j;
@@ -1939,29 +1938,20 @@
}
tiling_config |= BANK_SWAPS(1);
- cc_rb_backend_disable = RREG32(CC_RB_BACKEND_DISABLE) & 0x00ff0000;
- tmp = R6XX_MAX_BACKENDS -
- r600_count_pipe_bits((cc_rb_backend_disable >> 16) & R6XX_MAX_BACKENDS_MASK);
- if (tmp < rdev->config.r600.max_backends) {
- rdev->config.r600.max_backends = tmp;
- }
-
cc_gc_shader_pipe_config = RREG32(CC_GC_SHADER_PIPE_CONFIG) & 0x00ffff00;
- tmp = R6XX_MAX_PIPES -
- r600_count_pipe_bits((cc_gc_shader_pipe_config >> 8) & R6XX_MAX_PIPES_MASK);
- if (tmp < rdev->config.r600.max_pipes) {
- rdev->config.r600.max_pipes = tmp;
- }
- tmp = R6XX_MAX_SIMDS -
- r600_count_pipe_bits((cc_gc_shader_pipe_config >> 16) & R6XX_MAX_SIMDS_MASK);
- if (tmp < rdev->config.r600.max_simds) {
- rdev->config.r600.max_simds = tmp;
- }
tmp = rdev->config.r600.max_simds -
r600_count_pipe_bits((cc_gc_shader_pipe_config >> 16) & R6XX_MAX_SIMDS_MASK);
rdev->config.r600.active_simds = tmp;
disabled_rb_mask = (RREG32(CC_RB_BACKEND_DISABLE) >> 16) & R6XX_MAX_BACKENDS_MASK;
+ tmp = 0;
+ for (i = 0; i < rdev->config.r600.max_backends; i++)
+ tmp |= (1 << i);
+ /* if all the backends are disabled, fix it up here */
+ if ((disabled_rb_mask & tmp) == tmp) {
+ for (i = 0; i < rdev->config.r600.max_backends; i++)
+ disabled_rb_mask &= ~(1 << i);
+ }
tmp = (tiling_config & PIPE_TILING__MASK) >> PIPE_TILING__SHIFT;
tmp = r6xx_remap_render_backend(rdev, tmp, rdev->config.r600.max_backends,
R6XX_MAX_BACKENDS, disabled_rb_mask);
diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index b281886..5f05b4c 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -915,6 +915,8 @@
u64 vram_base_offset;
/* is vm enabled? */
bool enabled;
+ /* for hw to save the PD addr on suspend/resume */
+ uint32_t saved_table_addr[RADEON_NUM_VM];
};
/*
diff --git a/drivers/gpu/drm/radeon/rv770.c b/drivers/gpu/drm/radeon/rv770.c
index 2983f17..d9f5ce7 100644
--- a/drivers/gpu/drm/radeon/rv770.c
+++ b/drivers/gpu/drm/radeon/rv770.c
@@ -1177,7 +1177,6 @@
u32 hdp_host_path_cntl;
u32 sq_dyn_gpr_size_simd_ab_0;
u32 gb_tiling_config = 0;
- u32 cc_rb_backend_disable = 0;
u32 cc_gc_shader_pipe_config = 0;
u32 mc_arb_ramcfg;
u32 db_debug4, tmp;
@@ -1311,21 +1310,7 @@
WREG32(SPI_CONFIG_CNTL, 0);
}
- cc_rb_backend_disable = RREG32(CC_RB_BACKEND_DISABLE) & 0x00ff0000;
- tmp = R7XX_MAX_BACKENDS - r600_count_pipe_bits(cc_rb_backend_disable >> 16);
- if (tmp < rdev->config.rv770.max_backends) {
- rdev->config.rv770.max_backends = tmp;
- }
-
cc_gc_shader_pipe_config = RREG32(CC_GC_SHADER_PIPE_CONFIG) & 0xffffff00;
- tmp = R7XX_MAX_PIPES - r600_count_pipe_bits((cc_gc_shader_pipe_config >> 8) & R7XX_MAX_PIPES_MASK);
- if (tmp < rdev->config.rv770.max_pipes) {
- rdev->config.rv770.max_pipes = tmp;
- }
- tmp = R7XX_MAX_SIMDS - r600_count_pipe_bits((cc_gc_shader_pipe_config >> 16) & R7XX_MAX_SIMDS_MASK);
- if (tmp < rdev->config.rv770.max_simds) {
- rdev->config.rv770.max_simds = tmp;
- }
tmp = rdev->config.rv770.max_simds -
r600_count_pipe_bits((cc_gc_shader_pipe_config >> 16) & R7XX_MAX_SIMDS_MASK);
rdev->config.rv770.active_simds = tmp;
@@ -1348,6 +1333,14 @@
rdev->config.rv770.tiling_npipes = rdev->config.rv770.max_tile_pipes;
disabled_rb_mask = (RREG32(CC_RB_BACKEND_DISABLE) >> 16) & R7XX_MAX_BACKENDS_MASK;
+ tmp = 0;
+ for (i = 0; i < rdev->config.rv770.max_backends; i++)
+ tmp |= (1 << i);
+ /* if all the backends are disabled, fix it up here */
+ if ((disabled_rb_mask & tmp) == tmp) {
+ for (i = 0; i < rdev->config.rv770.max_backends; i++)
+ disabled_rb_mask &= ~(1 << i);
+ }
tmp = (gb_tiling_config & PIPE_TILING__MASK) >> PIPE_TILING__SHIFT;
tmp = r6xx_remap_render_backend(rdev, tmp, rdev->config.rv770.max_backends,
R7XX_MAX_BACKENDS, disabled_rb_mask);
diff --git a/drivers/gpu/drm/radeon/si.c b/drivers/gpu/drm/radeon/si.c
index a1274a3..6bce408 100644
--- a/drivers/gpu/drm/radeon/si.c
+++ b/drivers/gpu/drm/radeon/si.c
@@ -4290,10 +4290,10 @@
for (i = 1; i < 16; i++) {
if (i < 8)
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2),
- rdev->gart.table_addr >> 12);
+ rdev->vm_manager.saved_table_addr[i]);
else
WREG32(VM_CONTEXT8_PAGE_TABLE_BASE_ADDR + ((i - 8) << 2),
- rdev->gart.table_addr >> 12);
+ rdev->vm_manager.saved_table_addr[i]);
}
/* enable context1-15 */
@@ -4325,6 +4325,17 @@
static void si_pcie_gart_disable(struct radeon_device *rdev)
{
+ unsigned i;
+
+ for (i = 1; i < 16; ++i) {
+ uint32_t reg;
+ if (i < 8)
+ reg = VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2);
+ else
+ reg = VM_CONTEXT8_PAGE_TABLE_BASE_ADDR + ((i - 8) << 2);
+ rdev->vm_manager.saved_table_addr[i] = RREG32(reg);
+ }
+
/* Disable all tables */
WREG32(VM_CONTEXT0_CNTL, 0);
WREG32(VM_CONTEXT1_CNTL, 0);
@@ -7177,6 +7188,9 @@
int ret, i;
u16 tmp16;
+ if (pci_is_root_bus(rdev->pdev->bus))
+ return;
+
if (radeon_pcie_gen2 == 0)
return;
@@ -7454,7 +7468,8 @@
if (orig != data)
WREG32_PIF_PHY1(PB1_PIF_CNTL, data);
- if (!disable_clkreq) {
+ if (!disable_clkreq &&
+ !pci_is_root_bus(rdev->pdev->bus)) {
struct pci_dev *root = rdev->pdev->bus->self;
u32 lnkcap;
diff --git a/drivers/gpu/drm/sti/Kconfig b/drivers/gpu/drm/sti/Kconfig
index 2d9d425..ae8850f 100644
--- a/drivers/gpu/drm/sti/Kconfig
+++ b/drivers/gpu/drm/sti/Kconfig
@@ -1,6 +1,7 @@
config DRM_STI
tristate "DRM Support for STMicroelectronics SoC stiH41x Series"
depends on DRM && (SOC_STIH415 || SOC_STIH416 || ARCH_MULTIPLATFORM)
+ select RESET_CONTROLLER
select DRM_KMS_HELPER
select DRM_GEM_CMA_HELPER
select DRM_KMS_CMA_HELPER
diff --git a/drivers/gpu/drm/sti/sti_drm_drv.c b/drivers/gpu/drm/sti/sti_drm_drv.c
index a7cc249..223d93c 100644
--- a/drivers/gpu/drm/sti/sti_drm_drv.c
+++ b/drivers/gpu/drm/sti/sti_drm_drv.c
@@ -201,8 +201,8 @@
master = platform_device_register_resndata(dev,
DRIVER_NAME "__master", -1,
NULL, 0, NULL, 0);
- if (!master)
- return -EINVAL;
+ if (IS_ERR(master))
+ return PTR_ERR(master);
platform_set_drvdata(pdev, master);
return 0;
diff --git a/drivers/gpu/drm/sti/sti_hda.c b/drivers/gpu/drm/sti/sti_hda.c
index 72d957f..2ae9a9b 100644
--- a/drivers/gpu/drm/sti/sti_hda.c
+++ b/drivers/gpu/drm/sti/sti_hda.c
@@ -730,16 +730,16 @@
return -ENOMEM;
}
hda->regs = devm_ioremap_nocache(dev, res->start, resource_size(res));
- if (IS_ERR(hda->regs))
- return PTR_ERR(hda->regs);
+ if (!hda->regs)
+ return -ENOMEM;
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
"video-dacs-ctrl");
if (res) {
hda->video_dacs_ctrl = devm_ioremap_nocache(dev, res->start,
resource_size(res));
- if (IS_ERR(hda->video_dacs_ctrl))
- return PTR_ERR(hda->video_dacs_ctrl);
+ if (!hda->video_dacs_ctrl)
+ return -ENOMEM;
} else {
/* If no existing video-dacs-ctrl resource continue the probe */
DRM_DEBUG_DRIVER("No video-dacs-ctrl resource\n");
@@ -770,7 +770,7 @@
return 0;
}
-static struct of_device_id hda_of_match[] = {
+static const struct of_device_id hda_of_match[] = {
{ .compatible = "st,stih416-hda", },
{ .compatible = "st,stih407-hda", },
{ /* end node */ }
diff --git a/drivers/gpu/drm/sti/sti_hdmi.c b/drivers/gpu/drm/sti/sti_hdmi.c
index 284e541..ef93156 100644
--- a/drivers/gpu/drm/sti/sti_hdmi.c
+++ b/drivers/gpu/drm/sti/sti_hdmi.c
@@ -677,7 +677,7 @@
.unbind = sti_hdmi_unbind,
};
-static struct of_device_id hdmi_of_match[] = {
+static const struct of_device_id hdmi_of_match[] = {
{
.compatible = "st,stih416-hdmi",
.data = &tx3g0c55phy_ops,
@@ -713,8 +713,8 @@
return -ENOMEM;
}
hdmi->regs = devm_ioremap_nocache(dev, res->start, resource_size(res));
- if (IS_ERR(hdmi->regs))
- return PTR_ERR(hdmi->regs);
+ if (!hdmi->regs)
+ return -ENOMEM;
if (of_device_is_compatible(np, "st,stih416-hdmi")) {
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
@@ -725,8 +725,8 @@
}
hdmi->syscfg = devm_ioremap_nocache(dev, res->start,
resource_size(res));
- if (IS_ERR(hdmi->syscfg))
- return PTR_ERR(hdmi->syscfg);
+ if (!hdmi->syscfg)
+ return -ENOMEM;
}
diff --git a/drivers/gpu/drm/sti/sti_tvout.c b/drivers/gpu/drm/sti/sti_tvout.c
index b69e26f..b8afe49 100644
--- a/drivers/gpu/drm/sti/sti_tvout.c
+++ b/drivers/gpu/drm/sti/sti_tvout.c
@@ -591,8 +591,8 @@
return -ENOMEM;
}
tvout->regs = devm_ioremap_nocache(dev, res->start, resource_size(res));
- if (IS_ERR(tvout->regs))
- return PTR_ERR(tvout->regs);
+ if (!tvout->regs)
+ return -ENOMEM;
/* get reset resources */
tvout->reset = devm_reset_control_get(dev, "tvout");
@@ -624,7 +624,7 @@
return 0;
}
-static struct of_device_id tvout_of_match[] = {
+static const struct of_device_id tvout_of_match[] = {
{ .compatible = "st,stih416-tvout", },
{ .compatible = "st,stih407-tvout", },
{ /* end node */ }
diff --git a/drivers/hid/hid-logitech-dj.c b/drivers/hid/hid-logitech-dj.c
index b7ba829..9bf8637 100644
--- a/drivers/hid/hid-logitech-dj.c
+++ b/drivers/hid/hid-logitech-dj.c
@@ -656,7 +656,6 @@
struct dj_receiver_dev *djrcv_dev = hid_get_drvdata(hdev);
struct dj_report *dj_report = (struct dj_report *) data;
unsigned long flags;
- bool report_processed = false;
dbg_hid("%s, size:%d\n", __func__, size);
@@ -683,34 +682,42 @@
* device (via hid_input_report() ) and return 1 so hid-core does not do
* anything else with it.
*/
+
+ /* case 1) */
+ if (data[0] != REPORT_ID_DJ_SHORT)
+ return false;
+
if ((dj_report->device_index < DJ_DEVICE_INDEX_MIN) ||
(dj_report->device_index > DJ_DEVICE_INDEX_MAX)) {
- dev_err(&hdev->dev, "%s: invalid device index:%d\n",
+ /*
+ * Device index is wrong, bail out.
+ * This driver can ignore safely the receiver notifications,
+ * so ignore those reports too.
+ */
+ if (dj_report->device_index != DJ_RECEIVER_INDEX)
+ dev_err(&hdev->dev, "%s: invalid device index:%d\n",
__func__, dj_report->device_index);
return false;
}
spin_lock_irqsave(&djrcv_dev->lock, flags);
- if (dj_report->report_id == REPORT_ID_DJ_SHORT) {
- switch (dj_report->report_type) {
- case REPORT_TYPE_NOTIF_DEVICE_PAIRED:
- case REPORT_TYPE_NOTIF_DEVICE_UNPAIRED:
- logi_dj_recv_queue_notification(djrcv_dev, dj_report);
- break;
- case REPORT_TYPE_NOTIF_CONNECTION_STATUS:
- if (dj_report->report_params[CONNECTION_STATUS_PARAM_STATUS] ==
- STATUS_LINKLOSS) {
- logi_dj_recv_forward_null_report(djrcv_dev, dj_report);
- }
- break;
- default:
- logi_dj_recv_forward_report(djrcv_dev, dj_report);
+ switch (dj_report->report_type) {
+ case REPORT_TYPE_NOTIF_DEVICE_PAIRED:
+ case REPORT_TYPE_NOTIF_DEVICE_UNPAIRED:
+ logi_dj_recv_queue_notification(djrcv_dev, dj_report);
+ break;
+ case REPORT_TYPE_NOTIF_CONNECTION_STATUS:
+ if (dj_report->report_params[CONNECTION_STATUS_PARAM_STATUS] ==
+ STATUS_LINKLOSS) {
+ logi_dj_recv_forward_null_report(djrcv_dev, dj_report);
}
- report_processed = true;
+ break;
+ default:
+ logi_dj_recv_forward_report(djrcv_dev, dj_report);
}
spin_unlock_irqrestore(&djrcv_dev->lock, flags);
- return report_processed;
+ return true;
}
static int logi_dj_probe(struct hid_device *hdev,
diff --git a/drivers/hid/hid-logitech-dj.h b/drivers/hid/hid-logitech-dj.h
index 4a40003..daeb0aa 100644
--- a/drivers/hid/hid-logitech-dj.h
+++ b/drivers/hid/hid-logitech-dj.h
@@ -27,6 +27,7 @@
#define DJ_MAX_PAIRED_DEVICES 6
#define DJ_MAX_NUMBER_NOTIFICATIONS 8
+#define DJ_RECEIVER_INDEX 0
#define DJ_DEVICE_INDEX_MIN 1
#define DJ_DEVICE_INDEX_MAX 6
diff --git a/drivers/hid/hid-magicmouse.c b/drivers/hid/hid-magicmouse.c
index ecc2cbf..29a74c1 100644
--- a/drivers/hid/hid-magicmouse.c
+++ b/drivers/hid/hid-magicmouse.c
@@ -290,6 +290,11 @@
if (size < 4 || ((size - 4) % 9) != 0)
return 0;
npoints = (size - 4) / 9;
+ if (npoints > 15) {
+ hid_warn(hdev, "invalid size value (%d) for TRACKPAD_REPORT_ID\n",
+ size);
+ return 0;
+ }
msc->ntouches = 0;
for (ii = 0; ii < npoints; ii++)
magicmouse_emit_touch(msc, ii, data + ii * 9 + 4);
@@ -307,6 +312,11 @@
if (size < 6 || ((size - 6) % 8) != 0)
return 0;
npoints = (size - 6) / 8;
+ if (npoints > 15) {
+ hid_warn(hdev, "invalid size value (%d) for MOUSE_REPORT_ID\n",
+ size);
+ return 0;
+ }
msc->ntouches = 0;
for (ii = 0; ii < npoints; ii++)
magicmouse_emit_touch(msc, ii, data + ii * 8 + 6);
diff --git a/drivers/hid/hid-picolcd_core.c b/drivers/hid/hid-picolcd_core.c
index acbb0210..020df3c 100644
--- a/drivers/hid/hid-picolcd_core.c
+++ b/drivers/hid/hid-picolcd_core.c
@@ -350,6 +350,12 @@
if (!data)
return 1;
+ if (size > 64) {
+ hid_warn(hdev, "invalid size value (%d) for picolcd raw event\n",
+ size);
+ return 0;
+ }
+
if (report->id == REPORT_KEY_STATE) {
if (data->input_keys)
ret = picolcd_raw_keypad(data, report, raw_data+1, size-1);
diff --git a/drivers/md/dm-crypt.c b/drivers/md/dm-crypt.c
index 2785007..cd15e08 100644
--- a/drivers/md/dm-crypt.c
+++ b/drivers/md/dm-crypt.c
@@ -1688,6 +1688,7 @@
unsigned int key_size, opt_params;
unsigned long long tmpll;
int ret;
+ size_t iv_size_padding;
struct dm_arg_set as;
const char *opt_string;
char dummy;
@@ -1724,20 +1725,32 @@
cc->dmreq_start = sizeof(struct ablkcipher_request);
cc->dmreq_start += crypto_ablkcipher_reqsize(any_tfm(cc));
- cc->dmreq_start = ALIGN(cc->dmreq_start, crypto_tfm_ctx_alignment());
- cc->dmreq_start += crypto_ablkcipher_alignmask(any_tfm(cc)) &
- ~(crypto_tfm_ctx_alignment() - 1);
+ cc->dmreq_start = ALIGN(cc->dmreq_start, __alignof__(struct dm_crypt_request));
+
+ if (crypto_ablkcipher_alignmask(any_tfm(cc)) < CRYPTO_MINALIGN) {
+ /* Allocate the padding exactly */
+ iv_size_padding = -(cc->dmreq_start + sizeof(struct dm_crypt_request))
+ & crypto_ablkcipher_alignmask(any_tfm(cc));
+ } else {
+ /*
+ * If the cipher requires greater alignment than kmalloc
+ * alignment, we don't know the exact position of the
+ * initialization vector. We must assume worst case.
+ */
+ iv_size_padding = crypto_ablkcipher_alignmask(any_tfm(cc));
+ }
cc->req_pool = mempool_create_kmalloc_pool(MIN_IOS, cc->dmreq_start +
- sizeof(struct dm_crypt_request) + cc->iv_size);
+ sizeof(struct dm_crypt_request) + iv_size_padding + cc->iv_size);
if (!cc->req_pool) {
ti->error = "Cannot allocate crypt request mempool";
goto bad;
}
cc->per_bio_data_size = ti->per_bio_data_size =
- sizeof(struct dm_crypt_io) + cc->dmreq_start +
- sizeof(struct dm_crypt_request) + cc->iv_size;
+ ALIGN(sizeof(struct dm_crypt_io) + cc->dmreq_start +
+ sizeof(struct dm_crypt_request) + iv_size_padding + cc->iv_size,
+ ARCH_KMALLOC_MINALIGN);
cc->page_pool = mempool_create_page_pool(MIN_POOL_PAGES, 0);
if (!cc->page_pool) {
diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c
index ce48aa7..bde2fc0 100644
--- a/drivers/mfd/ab8500-core.c
+++ b/drivers/mfd/ab8500-core.c
@@ -1754,7 +1754,7 @@
if (ret)
return ret;
-#if CONFIG_DEBUG_FS
+#ifdef CONFIG_DEBUG_FS
/* Pass to debugfs */
ab8500_debug_resources[0].start = ab8500->irq;
ab8500_debug_resources[0].end = ab8500->irq;
diff --git a/drivers/mfd/htc-i2cpld.c b/drivers/mfd/htc-i2cpld.c
index b44f020..6bdb78c 100644
--- a/drivers/mfd/htc-i2cpld.c
+++ b/drivers/mfd/htc-i2cpld.c
@@ -404,7 +404,7 @@
}
i2c_set_clientdata(client, chip);
- snprintf(client->name, I2C_NAME_SIZE, "Chip_0x%d", client->addr);
+ snprintf(client->name, I2C_NAME_SIZE, "Chip_0x%x", client->addr);
chip->client = client;
/* Reset the chip */
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index 33a9234..83dab2f 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -647,7 +647,7 @@
default:
omap->nports = OMAP3_HS_USB_PORTS;
dev_dbg(dev,
- "USB HOST Rev:0x%d not recognized, assuming %d ports\n",
+ "USB HOST Rev:0x%x not recognized, assuming %d ports\n",
omap->usbhs_rev, omap->nports);
break;
}
diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c
index 3bc969a..4d3ff37 100644
--- a/drivers/mfd/twl4030-power.c
+++ b/drivers/mfd/twl4030-power.c
@@ -724,24 +724,24 @@
* above.
*/
static struct twl4030_resconfig omap3_idle_rconfig[] = {
- TWL_REMAP_SLEEP(RES_VAUX1, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VAUX2, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VAUX3, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VAUX4, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VMMC1, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VMMC2, DEV_GRP_NULL, 0, 0),
+ TWL_REMAP_SLEEP(RES_VAUX1, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VAUX2, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VAUX3, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VAUX4, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VMMC1, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VMMC2, TWL4030_RESCONFIG_UNDEF, 0, 0),
TWL_REMAP_OFF(RES_VPLL1, DEV_GRP_P1, 3, 1),
TWL_REMAP_SLEEP(RES_VPLL2, DEV_GRP_P1, 0, 0),
- TWL_REMAP_SLEEP(RES_VSIM, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VDAC, DEV_GRP_NULL, 0, 0),
+ TWL_REMAP_SLEEP(RES_VSIM, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VDAC, TWL4030_RESCONFIG_UNDEF, 0, 0),
TWL_REMAP_SLEEP(RES_VINTANA1, TWL_DEV_GRP_P123, 1, 2),
TWL_REMAP_SLEEP(RES_VINTANA2, TWL_DEV_GRP_P123, 0, 2),
TWL_REMAP_SLEEP(RES_VINTDIG, TWL_DEV_GRP_P123, 1, 2),
TWL_REMAP_SLEEP(RES_VIO, TWL_DEV_GRP_P123, 2, 2),
TWL_REMAP_OFF(RES_VDD1, DEV_GRP_P1, 4, 1),
TWL_REMAP_OFF(RES_VDD2, DEV_GRP_P1, 3, 1),
- TWL_REMAP_SLEEP(RES_VUSB_1V5, DEV_GRP_NULL, 0, 0),
- TWL_REMAP_SLEEP(RES_VUSB_1V8, DEV_GRP_NULL, 0, 0),
+ TWL_REMAP_SLEEP(RES_VUSB_1V5, TWL4030_RESCONFIG_UNDEF, 0, 0),
+ TWL_REMAP_SLEEP(RES_VUSB_1V8, TWL4030_RESCONFIG_UNDEF, 0, 0),
TWL_REMAP_SLEEP(RES_VUSB_3V1, TWL_DEV_GRP_P123, 0, 0),
/* Resource #20 USB charge pump skipped */
TWL_REMAP_SLEEP(RES_REGEN, TWL_DEV_GRP_P123, 2, 1),
diff --git a/drivers/misc/mei/client.c b/drivers/misc/mei/client.c
index 324e1de..2da05c0 100644
--- a/drivers/misc/mei/client.c
+++ b/drivers/misc/mei/client.c
@@ -601,6 +601,7 @@
cl->timer_count = MEI_CONNECT_TIMEOUT;
list_add_tail(&cb->list, &dev->ctrl_rd_list.list);
} else {
+ cl->state = MEI_FILE_INITIALIZING;
list_add_tail(&cb->list, &dev->ctrl_wr_list.list);
}
diff --git a/drivers/misc/mei/nfc.c b/drivers/misc/mei/nfc.c
index 3095fc5..5ccc23b 100644
--- a/drivers/misc/mei/nfc.c
+++ b/drivers/misc/mei/nfc.c
@@ -342,9 +342,10 @@
ndev = (struct mei_nfc_dev *) cldev->priv_data;
dev = ndev->cl->dev;
+ err = -ENOMEM;
mei_buf = kzalloc(length + MEI_NFC_HEADER_SIZE, GFP_KERNEL);
if (!mei_buf)
- return -ENOMEM;
+ goto out;
hdr = (struct mei_nfc_hci_hdr *) mei_buf;
hdr->cmd = MEI_NFC_CMD_HCI_SEND;
@@ -354,12 +355,9 @@
hdr->data_size = length;
memcpy(mei_buf + MEI_NFC_HEADER_SIZE, buf, length);
-
err = __mei_cl_send(ndev->cl, mei_buf, length + MEI_NFC_HEADER_SIZE);
if (err < 0)
- return err;
-
- kfree(mei_buf);
+ goto out;
if (!wait_event_interruptible_timeout(ndev->send_wq,
ndev->recv_req_id == ndev->req_id, HZ)) {
@@ -368,7 +366,8 @@
} else {
ndev->req_id++;
}
-
+out:
+ kfree(mei_buf);
return err;
}
diff --git a/drivers/pinctrl/nomadik/pinctrl-abx500.c b/drivers/pinctrl/nomadik/pinctrl-abx500.c
index a53a689..8c6fd8d 100644
--- a/drivers/pinctrl/nomadik/pinctrl-abx500.c
+++ b/drivers/pinctrl/nomadik/pinctrl-abx500.c
@@ -620,8 +620,7 @@
} else
seq_printf(s, " %-9s", chip->get(chip, offset) ? "hi" : "lo");
- if (pctldev)
- mode = abx500_get_mode(pctldev, chip, offset);
+ mode = abx500_get_mode(pctldev, chip, offset);
seq_printf(s, " %s", (mode < 0) ? "unknown" : modes[mode]);
diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c
index af1ba4f..60464a2 100644
--- a/drivers/pinctrl/pinctrl-at91.c
+++ b/drivers/pinctrl/pinctrl-at91.c
@@ -497,10 +497,10 @@
static void at91_pin_dbg(const struct device *dev, const struct at91_pmx_pin *pin)
{
if (pin->mux) {
- dev_dbg(dev, "pio%c%d configured as periph%c with conf = 0x%lu\n",
+ dev_dbg(dev, "pio%c%d configured as periph%c with conf = 0x%lx\n",
pin->bank + 'A', pin->pin, pin->mux - 1 + 'A', pin->conf);
} else {
- dev_dbg(dev, "pio%c%d configured as gpio with conf = 0x%lu\n",
+ dev_dbg(dev, "pio%c%d configured as gpio with conf = 0x%lx\n",
pin->bank + 'A', pin->pin, pin->conf);
}
}
diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
index 5e8b2e0..0c372a3 100644
--- a/drivers/pinctrl/pinctrl-rockchip.c
+++ b/drivers/pinctrl/pinctrl-rockchip.c
@@ -438,7 +438,7 @@
int reg, ret, mask;
unsigned long flags;
u8 bit;
- u32 data;
+ u32 data, rmask;
if (iomux_num > 3)
return -EINVAL;
@@ -478,8 +478,9 @@
spin_lock_irqsave(&bank->slock, flags);
data = (mask << (bit + 16));
+ rmask = data | (data >> 16);
data |= (mux & mask) << bit;
- ret = regmap_write(regmap, reg, data);
+ ret = regmap_update_bits(regmap, reg, rmask, data);
spin_unlock_irqrestore(&bank->slock, flags);
@@ -634,7 +635,7 @@
struct regmap *regmap;
unsigned long flags;
int reg, ret, i;
- u32 data;
+ u32 data, rmask;
u8 bit;
rk3288_calc_drv_reg_and_bit(bank, pin_num, ®map, ®, &bit);
@@ -657,9 +658,10 @@
/* enable the write to the equivalent lower bits */
data = ((1 << RK3288_DRV_BITS_PER_PIN) - 1) << (bit + 16);
+ rmask = data | (data >> 16);
data |= (ret << bit);
- ret = regmap_write(regmap, reg, data);
+ ret = regmap_update_bits(regmap, reg, rmask, data);
spin_unlock_irqrestore(&bank->slock, flags);
return ret;
@@ -722,7 +724,7 @@
int reg, ret;
unsigned long flags;
u8 bit;
- u32 data;
+ u32 data, rmask;
dev_dbg(info->dev, "setting pull of GPIO%d-%d to %d\n",
bank->bank_num, pin_num, pull);
@@ -750,6 +752,7 @@
/* enable the write to the equivalent lower bits */
data = ((1 << RK3188_PULL_BITS_PER_PIN) - 1) << (bit + 16);
+ rmask = data | (data >> 16);
switch (pull) {
case PIN_CONFIG_BIAS_DISABLE:
@@ -770,7 +773,7 @@
return -EINVAL;
}
- ret = regmap_write(regmap, reg, data);
+ ret = regmap_update_bits(regmap, reg, rmask, data);
spin_unlock_irqrestore(&bank->slock, flags);
break;
diff --git a/drivers/pinctrl/pinctrl-tegra-xusb.c b/drivers/pinctrl/pinctrl-tegra-xusb.c
index a066204..e641b42 100644
--- a/drivers/pinctrl/pinctrl-tegra-xusb.c
+++ b/drivers/pinctrl/pinctrl-tegra-xusb.c
@@ -680,7 +680,7 @@
if (args->args_count <= 0)
return ERR_PTR(-EINVAL);
- if (index > ARRAY_SIZE(padctl->phys))
+ if (index >= ARRAY_SIZE(padctl->phys))
return ERR_PTR(-EINVAL);
return padctl->phys[index];
@@ -930,7 +930,8 @@
padctl->provider = devm_of_phy_provider_register(&pdev->dev,
tegra_xusb_padctl_xlate);
- if (err < 0) {
+ if (IS_ERR(padctl->provider)) {
+ err = PTR_ERR(padctl->provider);
dev_err(&pdev->dev, "failed to register PHYs: %d\n", err);
goto unregister;
}
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index 003bfd8..d7154ed 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -127,14 +127,10 @@
struct irq_chip *chip = irq_data_get_irq_chip(irqd);
struct exynos_irq_chip *our_chip = to_exynos_irq_chip(chip);
struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
- struct samsung_pin_bank_type *bank_type = bank->type;
struct samsung_pinctrl_drv_data *d = bank->drvdata;
- unsigned int pin = irqd->hwirq;
- unsigned int shift = EXYNOS_EINT_CON_LEN * pin;
+ unsigned int shift = EXYNOS_EINT_CON_LEN * irqd->hwirq;
unsigned int con, trig_type;
unsigned long reg_con = our_chip->eint_con + bank->eint_offset;
- unsigned long flags;
- unsigned int mask;
switch (type) {
case IRQ_TYPE_EDGE_RISING:
@@ -167,8 +163,32 @@
con |= trig_type << shift;
writel(con, d->virt_base + reg_con);
+ return 0;
+}
+
+static int exynos_irq_request_resources(struct irq_data *irqd)
+{
+ struct irq_chip *chip = irq_data_get_irq_chip(irqd);
+ struct exynos_irq_chip *our_chip = to_exynos_irq_chip(chip);
+ struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
+ struct samsung_pin_bank_type *bank_type = bank->type;
+ struct samsung_pinctrl_drv_data *d = bank->drvdata;
+ unsigned int shift = EXYNOS_EINT_CON_LEN * irqd->hwirq;
+ unsigned long reg_con = our_chip->eint_con + bank->eint_offset;
+ unsigned long flags;
+ unsigned int mask;
+ unsigned int con;
+ int ret;
+
+ ret = gpio_lock_as_irq(&bank->gpio_chip, irqd->hwirq);
+ if (ret) {
+ dev_err(bank->gpio_chip.dev, "unable to lock pin %s-%lu IRQ\n",
+ bank->name, irqd->hwirq);
+ return ret;
+ }
+
reg_con = bank->pctl_offset + bank_type->reg_offset[PINCFG_TYPE_FUNC];
- shift = pin * bank_type->fld_width[PINCFG_TYPE_FUNC];
+ shift = irqd->hwirq * bank_type->fld_width[PINCFG_TYPE_FUNC];
mask = (1 << bank_type->fld_width[PINCFG_TYPE_FUNC]) - 1;
spin_lock_irqsave(&bank->slock, flags);
@@ -180,9 +200,42 @@
spin_unlock_irqrestore(&bank->slock, flags);
+ exynos_irq_unmask(irqd);
+
return 0;
}
+static void exynos_irq_release_resources(struct irq_data *irqd)
+{
+ struct irq_chip *chip = irq_data_get_irq_chip(irqd);
+ struct exynos_irq_chip *our_chip = to_exynos_irq_chip(chip);
+ struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
+ struct samsung_pin_bank_type *bank_type = bank->type;
+ struct samsung_pinctrl_drv_data *d = bank->drvdata;
+ unsigned int shift = EXYNOS_EINT_CON_LEN * irqd->hwirq;
+ unsigned long reg_con = our_chip->eint_con + bank->eint_offset;
+ unsigned long flags;
+ unsigned int mask;
+ unsigned int con;
+
+ reg_con = bank->pctl_offset + bank_type->reg_offset[PINCFG_TYPE_FUNC];
+ shift = irqd->hwirq * bank_type->fld_width[PINCFG_TYPE_FUNC];
+ mask = (1 << bank_type->fld_width[PINCFG_TYPE_FUNC]) - 1;
+
+ exynos_irq_mask(irqd);
+
+ spin_lock_irqsave(&bank->slock, flags);
+
+ con = readl(d->virt_base + reg_con);
+ con &= ~(mask << shift);
+ con |= FUNC_INPUT << shift;
+ writel(con, d->virt_base + reg_con);
+
+ spin_unlock_irqrestore(&bank->slock, flags);
+
+ gpio_unlock_as_irq(&bank->gpio_chip, irqd->hwirq);
+}
+
/*
* irq_chip for gpio interrupts.
*/
@@ -193,6 +246,8 @@
.irq_mask = exynos_irq_mask,
.irq_ack = exynos_irq_ack,
.irq_set_type = exynos_irq_set_type,
+ .irq_request_resources = exynos_irq_request_resources,
+ .irq_release_resources = exynos_irq_release_resources,
},
.eint_con = EXYNOS_GPIO_ECON_OFFSET,
.eint_mask = EXYNOS_GPIO_EMASK_OFFSET,
@@ -336,6 +391,8 @@
.irq_ack = exynos_irq_ack,
.irq_set_type = exynos_irq_set_type,
.irq_set_wake = exynos_wkup_irq_set_wake,
+ .irq_request_resources = exynos_irq_request_resources,
+ .irq_release_resources = exynos_irq_release_resources,
},
.eint_con = EXYNOS_WKUP_ECON_OFFSET,
.eint_mask = EXYNOS_WKUP_EMASK_OFFSET,
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h
index 2b88232..5cedc9d 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.h
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.h
@@ -26,6 +26,7 @@
#include <linux/gpio.h>
/* pinmux function number for pin as gpio output line */
+#define FUNC_INPUT 0x0
#define FUNC_OUTPUT 0x1
/**
diff --git a/drivers/pinctrl/sh-pfc/pfc-r8a7791.c b/drivers/pinctrl/sh-pfc/pfc-r8a7791.c
index 576d41b..c6e5deb 100644
--- a/drivers/pinctrl/sh-pfc/pfc-r8a7791.c
+++ b/drivers/pinctrl/sh-pfc/pfc-r8a7791.c
@@ -4509,24 +4509,24 @@
};
static const char * const can0_groups[] = {
- "can0_data_a",
+ "can0_data",
"can0_data_b",
"can0_data_c",
"can0_data_d",
"can0_data_e",
"can0_data_f",
- "can_clk_a",
+ "can_clk",
"can_clk_b",
"can_clk_c",
"can_clk_d",
};
static const char * const can1_groups[] = {
- "can1_data_a",
+ "can1_data",
"can1_data_b",
"can1_data_c",
"can1_data_d",
- "can_clk_a",
+ "can_clk",
"can_clk_b",
"can_clk_c",
"can_clk_d",
diff --git a/drivers/rtc/rtc-s5m.c b/drivers/rtc/rtc-s5m.c
index 8f06250..8754c33 100644
--- a/drivers/rtc/rtc-s5m.c
+++ b/drivers/rtc/rtc-s5m.c
@@ -717,12 +717,14 @@
info->device_type = s5m87xx->device_type;
info->wtsr_smpl = s5m87xx->wtsr_smpl;
- info->irq = regmap_irq_get_virq(s5m87xx->irq_data, alarm_irq);
- if (info->irq <= 0) {
- ret = -EINVAL;
- dev_err(&pdev->dev, "Failed to get virtual IRQ %d\n",
+ if (s5m87xx->irq_data) {
+ info->irq = regmap_irq_get_virq(s5m87xx->irq_data, alarm_irq);
+ if (info->irq <= 0) {
+ ret = -EINVAL;
+ dev_err(&pdev->dev, "Failed to get virtual IRQ %d\n",
alarm_irq);
- goto err;
+ goto err;
+ }
}
platform_set_drvdata(pdev, info);
@@ -744,6 +746,11 @@
goto err;
}
+ if (!info->irq) {
+ dev_info(&pdev->dev, "Alarm IRQ not available\n");
+ return 0;
+ }
+
ret = devm_request_threaded_irq(&pdev->dev, info->irq, NULL,
s5m_rtc_alarm_irq, 0, "rtc-alarm0",
info);
@@ -802,7 +809,7 @@
struct s5m_rtc_info *info = dev_get_drvdata(dev);
int ret = 0;
- if (device_may_wakeup(dev))
+ if (info->irq && device_may_wakeup(dev))
ret = disable_irq_wake(info->irq);
return ret;
@@ -813,7 +820,7 @@
struct s5m_rtc_info *info = dev_get_drvdata(dev);
int ret = 0;
- if (device_may_wakeup(dev))
+ if (info->irq && device_may_wakeup(dev))
ret = enable_irq_wake(info->irq);
return ret;
diff --git a/drivers/s390/char/con3215.c b/drivers/s390/char/con3215.c
index a6d47e5..c43aca6 100644
--- a/drivers/s390/char/con3215.c
+++ b/drivers/s390/char/con3215.c
@@ -1035,12 +1035,26 @@
const unsigned char *buf, int count)
{
struct raw3215_info *raw;
+ int i, written;
if (!tty)
return 0;
raw = (struct raw3215_info *) tty->driver_data;
- raw3215_write(raw, buf, count);
- return count;
+ written = count;
+ while (count > 0) {
+ for (i = 0; i < count; i++)
+ if (buf[i] == '\t' || buf[i] == '\n')
+ break;
+ raw3215_write(raw, buf, i);
+ count -= i;
+ buf += i;
+ if (count > 0) {
+ raw3215_putchar(raw, *buf);
+ count--;
+ buf++;
+ }
+ }
+ return written;
}
/*
@@ -1188,7 +1202,7 @@
driver->subtype = SYSTEM_TYPE_TTY;
driver->init_termios = tty_std_termios;
driver->init_termios.c_iflag = IGNBRK | IGNPAR;
- driver->init_termios.c_oflag = ONLCR | XTABS;
+ driver->init_termios.c_oflag = ONLCR;
driver->init_termios.c_lflag = ISIG;
driver->flags = TTY_DRIVER_REAL_RAW;
tty_set_operations(driver, &tty3215_ops);
diff --git a/drivers/s390/char/sclp_tty.c b/drivers/s390/char/sclp_tty.c
index 7ed7a59..0036632 100644
--- a/drivers/s390/char/sclp_tty.c
+++ b/drivers/s390/char/sclp_tty.c
@@ -559,7 +559,7 @@
driver->subtype = SYSTEM_TYPE_TTY;
driver->init_termios = tty_std_termios;
driver->init_termios.c_iflag = IGNBRK | IGNPAR;
- driver->init_termios.c_oflag = ONLCR | XTABS;
+ driver->init_termios.c_oflag = ONLCR;
driver->init_termios.c_lflag = ISIG | ECHO;
driver->flags = TTY_DRIVER_REAL_RAW;
tty_set_operations(driver, &sclp_ops);
diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c
index ce62e87..d837dc1 100644
--- a/drivers/scsi/scsi_lib.c
+++ b/drivers/scsi/scsi_lib.c
@@ -1808,7 +1808,6 @@
cmd->tag = req->tag;
- req->cmd = req->__cmd;
cmd->cmnd = req->cmd;
cmd->prot_op = SCSI_PROT_NORMAL;
diff --git a/drivers/spi/spi-au1550.c b/drivers/spi/spi-au1550.c
index 40c3d43..f40b34c 100644
--- a/drivers/spi/spi-au1550.c
+++ b/drivers/spi/spi-au1550.c
@@ -945,7 +945,7 @@
spi_bitbang_stop(&hw->bitbang);
free_irq(hw->irq, hw);
iounmap((void __iomem *)hw->regs);
- release_mem_region(r->start, sizeof(psc_spi_t));
+ release_mem_region(hw->ioarea->start, sizeof(psc_spi_t));
if (hw->usedma) {
au1550_spi_dma_rxtmp_free(hw);
diff --git a/drivers/spi/spi-davinci.c b/drivers/spi/spi-davinci.c
index 276a388..48f1d26 100644
--- a/drivers/spi/spi-davinci.c
+++ b/drivers/spi/spi-davinci.c
@@ -417,16 +417,16 @@
flags, dev_name(&spi->dev));
internal_cs = false;
}
- }
- if (retval) {
- dev_err(&spi->dev, "GPIO %d setup failed (%d)\n",
- spi->cs_gpio, retval);
- return retval;
- }
+ if (retval) {
+ dev_err(&spi->dev, "GPIO %d setup failed (%d)\n",
+ spi->cs_gpio, retval);
+ return retval;
+ }
- if (internal_cs)
- set_io_bits(dspi->base + SPIPC0, 1 << spi->chip_select);
+ if (internal_cs)
+ set_io_bits(dspi->base + SPIPC0, 1 << spi->chip_select);
+ }
if (spi->mode & SPI_READY)
set_io_bits(dspi->base + SPIPC0, SPIPC0_SPIENA_MASK);
diff --git a/drivers/spi/spi-dw-pci.c b/drivers/spi/spi-dw-pci.c
index 3f3dc12..e149604 100644
--- a/drivers/spi/spi-dw-pci.c
+++ b/drivers/spi/spi-dw-pci.c
@@ -62,6 +62,8 @@
if (ret)
return ret;
+ dws->regs = pcim_iomap_table(pdev)[pci_bar];
+
dws->bus_num = 0;
dws->num_cs = 4;
dws->irq = pdev->irq;
diff --git a/drivers/spi/spi-dw.c b/drivers/spi/spi-dw.c
index 29f3314..670f062 100644
--- a/drivers/spi/spi-dw.c
+++ b/drivers/spi/spi-dw.c
@@ -271,7 +271,7 @@
transfer_list);
if (!last_transfer->cs_change)
- spi_chip_sel(dws, dws->cur_msg->spi, 0);
+ spi_chip_sel(dws, msg->spi, 0);
spi_finalize_current_message(dws->master);
}
diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index 68441fa..352eed7 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -329,7 +329,8 @@
disable_fifo:
if (t->rx_buf != NULL)
chconf &= ~OMAP2_MCSPI_CHCONF_FFER;
- else
+
+ if (t->tx_buf != NULL)
chconf &= ~OMAP2_MCSPI_CHCONF_FFET;
mcspi_write_chconf0(spi, chconf);
diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c
index fe79210..46f45ca 100644
--- a/drivers/spi/spi-pxa2xx.c
+++ b/drivers/spi/spi-pxa2xx.c
@@ -1074,6 +1074,7 @@
{ "INT3430", 0 },
{ "INT3431", 0 },
{ "80860F0E", 0 },
+ { "8086228E", 0 },
{ },
};
MODULE_DEVICE_TABLE(acpi, pxa2xx_spi_acpi_match);
diff --git a/drivers/spi/spi-rockchip.c b/drivers/spi/spi-rockchip.c
index c074360..cd0e08b0 100644
--- a/drivers/spi/spi-rockchip.c
+++ b/drivers/spi/spi-rockchip.c
@@ -499,7 +499,7 @@
}
/* div doesn't support odd number */
- div = rs->max_freq / rs->speed;
+ div = max_t(u32, rs->max_freq / rs->speed, 1);
div = (div + 1) & 0xfffe;
spi_enable_chip(rs, 0);
@@ -678,7 +678,7 @@
rs->dma_tx.addr = (dma_addr_t)(mem->start + ROCKCHIP_SPI_TXDR);
rs->dma_rx.addr = (dma_addr_t)(mem->start + ROCKCHIP_SPI_RXDR);
rs->dma_tx.direction = DMA_MEM_TO_DEV;
- rs->dma_tx.direction = DMA_DEV_TO_MEM;
+ rs->dma_rx.direction = DMA_DEV_TO_MEM;
master->can_dma = rockchip_spi_can_dma;
master->dma_tx = rs->dma_tx.ch;
diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c
index c850dfd..ad87a98 100644
--- a/drivers/spi/spi-rspi.c
+++ b/drivers/spi/spi-rspi.c
@@ -472,25 +472,52 @@
dma_cookie_t cookie;
int ret;
- if (tx) {
- desc_tx = dmaengine_prep_slave_sg(rspi->master->dma_tx,
- tx->sgl, tx->nents, DMA_TO_DEVICE,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc_tx)
- goto no_dma;
-
- irq_mask |= SPCR_SPTIE;
- }
+ /* First prepare and submit the DMA request(s), as this may fail */
if (rx) {
desc_rx = dmaengine_prep_slave_sg(rspi->master->dma_rx,
rx->sgl, rx->nents, DMA_FROM_DEVICE,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc_rx)
- goto no_dma;
+ if (!desc_rx) {
+ ret = -EAGAIN;
+ goto no_dma_rx;
+ }
+
+ desc_rx->callback = rspi_dma_complete;
+ desc_rx->callback_param = rspi;
+ cookie = dmaengine_submit(desc_rx);
+ if (dma_submit_error(cookie)) {
+ ret = cookie;
+ goto no_dma_rx;
+ }
irq_mask |= SPCR_SPRIE;
}
+ if (tx) {
+ desc_tx = dmaengine_prep_slave_sg(rspi->master->dma_tx,
+ tx->sgl, tx->nents, DMA_TO_DEVICE,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc_tx) {
+ ret = -EAGAIN;
+ goto no_dma_tx;
+ }
+
+ if (rx) {
+ /* No callback */
+ desc_tx->callback = NULL;
+ } else {
+ desc_tx->callback = rspi_dma_complete;
+ desc_tx->callback_param = rspi;
+ }
+ cookie = dmaengine_submit(desc_tx);
+ if (dma_submit_error(cookie)) {
+ ret = cookie;
+ goto no_dma_tx;
+ }
+
+ irq_mask |= SPCR_SPTIE;
+ }
+
/*
* DMAC needs SPxIE, but if SPxIE is set, the IRQ routine will be
* called. So, this driver disables the IRQ while DMA transfer.
@@ -503,34 +530,24 @@
rspi_enable_irq(rspi, irq_mask);
rspi->dma_callbacked = 0;
- if (rx) {
- desc_rx->callback = rspi_dma_complete;
- desc_rx->callback_param = rspi;
- cookie = dmaengine_submit(desc_rx);
- if (dma_submit_error(cookie))
- return cookie;
+ /* Now start DMA */
+ if (rx)
dma_async_issue_pending(rspi->master->dma_rx);
- }
- if (tx) {
- if (rx) {
- /* No callback */
- desc_tx->callback = NULL;
- } else {
- desc_tx->callback = rspi_dma_complete;
- desc_tx->callback_param = rspi;
- }
- cookie = dmaengine_submit(desc_tx);
- if (dma_submit_error(cookie))
- return cookie;
+ if (tx)
dma_async_issue_pending(rspi->master->dma_tx);
- }
ret = wait_event_interruptible_timeout(rspi->wait,
rspi->dma_callbacked, HZ);
if (ret > 0 && rspi->dma_callbacked)
ret = 0;
- else if (!ret)
+ else if (!ret) {
+ dev_err(&rspi->master->dev, "DMA timeout\n");
ret = -ETIMEDOUT;
+ if (tx)
+ dmaengine_terminate_all(rspi->master->dma_tx);
+ if (rx)
+ dmaengine_terminate_all(rspi->master->dma_rx);
+ }
rspi_disable_irq(rspi, irq_mask);
@@ -541,11 +558,16 @@
return ret;
-no_dma:
- pr_warn_once("%s %s: DMA not available, falling back to PIO\n",
- dev_driver_string(&rspi->master->dev),
- dev_name(&rspi->master->dev));
- return -EAGAIN;
+no_dma_tx:
+ if (rx)
+ dmaengine_terminate_all(rspi->master->dma_rx);
+no_dma_rx:
+ if (ret == -EAGAIN) {
+ pr_warn_once("%s %s: DMA not available, falling back to PIO\n",
+ dev_driver_string(&rspi->master->dev),
+ dev_name(&rspi->master->dev));
+ }
+ return ret;
}
static void rspi_receive_init(const struct rspi_data *rspi)
diff --git a/drivers/spi/spi-sh-msiof.c b/drivers/spi/spi-sh-msiof.c
index 2a4354d..543075b 100644
--- a/drivers/spi/spi-sh-msiof.c
+++ b/drivers/spi/spi-sh-msiof.c
@@ -636,6 +636,26 @@
dma_cookie_t cookie;
int ret;
+ /* First prepare and submit the DMA request(s), as this may fail */
+ if (rx) {
+ ier_bits |= IER_RDREQE | IER_RDMAE;
+ desc_rx = dmaengine_prep_slave_single(p->master->dma_rx,
+ p->rx_dma_addr, len, DMA_FROM_DEVICE,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc_rx) {
+ ret = -EAGAIN;
+ goto no_dma_rx;
+ }
+
+ desc_rx->callback = sh_msiof_dma_complete;
+ desc_rx->callback_param = p;
+ cookie = dmaengine_submit(desc_rx);
+ if (dma_submit_error(cookie)) {
+ ret = cookie;
+ goto no_dma_rx;
+ }
+ }
+
if (tx) {
ier_bits |= IER_TDREQE | IER_TDMAE;
dma_sync_single_for_device(p->master->dma_tx->device->dev,
@@ -643,17 +663,23 @@
desc_tx = dmaengine_prep_slave_single(p->master->dma_tx,
p->tx_dma_addr, len, DMA_TO_DEVICE,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc_tx)
- return -EAGAIN;
- }
+ if (!desc_tx) {
+ ret = -EAGAIN;
+ goto no_dma_tx;
+ }
- if (rx) {
- ier_bits |= IER_RDREQE | IER_RDMAE;
- desc_rx = dmaengine_prep_slave_single(p->master->dma_rx,
- p->rx_dma_addr, len, DMA_FROM_DEVICE,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc_rx)
- return -EAGAIN;
+ if (rx) {
+ /* No callback */
+ desc_tx->callback = NULL;
+ } else {
+ desc_tx->callback = sh_msiof_dma_complete;
+ desc_tx->callback_param = p;
+ }
+ cookie = dmaengine_submit(desc_tx);
+ if (dma_submit_error(cookie)) {
+ ret = cookie;
+ goto no_dma_tx;
+ }
}
/* 1 stage FIFO watermarks for DMA */
@@ -666,37 +692,16 @@
reinit_completion(&p->done);
- if (rx) {
- desc_rx->callback = sh_msiof_dma_complete;
- desc_rx->callback_param = p;
- cookie = dmaengine_submit(desc_rx);
- if (dma_submit_error(cookie)) {
- ret = cookie;
- goto stop_ier;
- }
+ /* Now start DMA */
+ if (rx)
dma_async_issue_pending(p->master->dma_rx);
- }
-
- if (tx) {
- if (rx) {
- /* No callback */
- desc_tx->callback = NULL;
- } else {
- desc_tx->callback = sh_msiof_dma_complete;
- desc_tx->callback_param = p;
- }
- cookie = dmaengine_submit(desc_tx);
- if (dma_submit_error(cookie)) {
- ret = cookie;
- goto stop_rx;
- }
+ if (tx)
dma_async_issue_pending(p->master->dma_tx);
- }
ret = sh_msiof_spi_start(p, rx);
if (ret) {
dev_err(&p->pdev->dev, "failed to start hardware\n");
- goto stop_tx;
+ goto stop_dma;
}
/* wait for tx fifo to be emptied / rx fifo to be filled */
@@ -726,14 +731,14 @@
stop_reset:
sh_msiof_reset_str(p);
sh_msiof_spi_stop(p, rx);
-stop_tx:
+stop_dma:
if (tx)
dmaengine_terminate_all(p->master->dma_tx);
-stop_rx:
+no_dma_tx:
if (rx)
dmaengine_terminate_all(p->master->dma_rx);
-stop_ier:
sh_msiof_write(p, IER, 0);
+no_dma_rx:
return ret;
}
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index e0531ba..ca935df 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -848,6 +848,7 @@
/**
* spi_finalize_current_transfer - report completion of a transfer
+ * @master: the master reporting completion
*
* Called by SPI drivers using the core transfer_one_message()
* implementation to notify it that the current interrupt driven
diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig
index 2c486ea..35b494f 100644
--- a/drivers/staging/Kconfig
+++ b/drivers/staging/Kconfig
@@ -28,8 +28,6 @@
source "drivers/staging/slicoss/Kconfig"
-source "drivers/staging/usbip/Kconfig"
-
source "drivers/staging/wlan-ng/Kconfig"
source "drivers/staging/comedi/Kconfig"
diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile
index 1e1a3a1..e66a5db 100644
--- a/drivers/staging/Makefile
+++ b/drivers/staging/Makefile
@@ -6,7 +6,6 @@
obj-y += media/
obj-$(CONFIG_ET131X) += et131x/
obj-$(CONFIG_SLICOSS) += slicoss/
-obj-$(CONFIG_USBIP_CORE) += usbip/
obj-$(CONFIG_PRISM2_USB) += wlan-ng/
obj-$(CONFIG_COMEDI) += comedi/
obj-$(CONFIG_FB_OLPC_DCON) += olpc_dcon/
diff --git a/drivers/staging/android/logger.c b/drivers/staging/android/logger.c
index 9b47e66..0bf0d24 100644
--- a/drivers/staging/android/logger.c
+++ b/drivers/staging/android/logger.c
@@ -790,7 +790,7 @@
if (unlikely(ret)) {
pr_err("failed to register misc device for log '%s'!\n",
log->misc.name);
- goto out_free_log;
+ goto out_free_misc_name;
}
pr_info("created %luK log '%s'\n",
@@ -798,6 +798,9 @@
return 0;
+out_free_misc_name:
+ kfree(log->misc.name);
+
out_free_log:
kfree(log);
diff --git a/drivers/staging/et131x/et131x.c b/drivers/staging/et131x/et131x.c
index 8bf1eb4..831b7c6 100644
--- a/drivers/staging/et131x/et131x.c
+++ b/drivers/staging/et131x/et131x.c
@@ -1421,22 +1421,16 @@
* @reg: the register to read
* @value: 16-bit value to write
*/
-static int et131x_mii_write(struct et131x_adapter *adapter, u8 reg, u16 value)
+static int et131x_mii_write(struct et131x_adapter *adapter, u8 addr, u8 reg,
+ u16 value)
{
struct mac_regs __iomem *mac = &adapter->regs->mac;
- struct phy_device *phydev = adapter->phydev;
int status = 0;
- u8 addr;
u32 delay = 0;
u32 mii_addr;
u32 mii_cmd;
u32 mii_indicator;
- if (!phydev)
- return -EIO;
-
- addr = phydev->addr;
-
/* Save a local copy of the registers we are dealing with so we can
* set them back
*/
@@ -1631,17 +1625,7 @@
struct net_device *netdev = bus->priv;
struct et131x_adapter *adapter = netdev_priv(netdev);
- return et131x_mii_write(adapter, reg, value);
-}
-
-static int et131x_mdio_reset(struct mii_bus *bus)
-{
- struct net_device *netdev = bus->priv;
- struct et131x_adapter *adapter = netdev_priv(netdev);
-
- et131x_mii_write(adapter, MII_BMCR, BMCR_RESET);
-
- return 0;
+ return et131x_mii_write(adapter, phy_addr, reg, value);
}
/* et1310_phy_power_switch - PHY power control
@@ -1656,18 +1640,20 @@
static void et1310_phy_power_switch(struct et131x_adapter *adapter, bool down)
{
u16 data;
+ struct phy_device *phydev = adapter->phydev;
et131x_mii_read(adapter, MII_BMCR, &data);
data &= ~BMCR_PDOWN;
if (down)
data |= BMCR_PDOWN;
- et131x_mii_write(adapter, MII_BMCR, data);
+ et131x_mii_write(adapter, phydev->addr, MII_BMCR, data);
}
/* et131x_xcvr_init - Init the phy if we are setting it into force mode */
static void et131x_xcvr_init(struct et131x_adapter *adapter)
{
u16 lcr2;
+ struct phy_device *phydev = adapter->phydev;
/* Set the LED behavior such that LED 1 indicates speed (off =
* 10Mbits, blink = 100Mbits, on = 1000Mbits) and LED 2 indicates
@@ -1688,7 +1674,7 @@
else
lcr2 |= (LED_VAL_LINKON << LED_TXRX_SHIFT);
- et131x_mii_write(adapter, PHY_LED_2, lcr2);
+ et131x_mii_write(adapter, phydev->addr, PHY_LED_2, lcr2);
}
}
@@ -3643,14 +3629,14 @@
et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG,
®ister18);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18 | 0x4);
- et131x_mii_write(adapter, PHY_INDEX_REG,
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18 | 0x4);
+ et131x_mii_write(adapter, phydev->addr, PHY_INDEX_REG,
register18 | 0x8402);
- et131x_mii_write(adapter, PHY_DATA_REG,
+ et131x_mii_write(adapter, phydev->addr, PHY_DATA_REG,
register18 | 511);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18);
}
et1310_config_flow_control(adapter);
@@ -3662,7 +3648,8 @@
et131x_mii_read(adapter, PHY_CONFIG, ®);
reg &= ~ET_PHY_CONFIG_TX_FIFO_DEPTH;
reg |= ET_PHY_CONFIG_FIFO_DEPTH_32;
- et131x_mii_write(adapter, PHY_CONFIG, reg);
+ et131x_mii_write(adapter, phydev->addr, PHY_CONFIG,
+ reg);
}
et131x_set_rx_dma_timer(adapter);
@@ -3675,14 +3662,14 @@
et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG,
®ister18);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18 | 0x4);
- et131x_mii_write(adapter, PHY_INDEX_REG,
- register18 | 0x8402);
- et131x_mii_write(adapter, PHY_DATA_REG,
- register18 | 511);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18 | 0x4);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_INDEX_REG, register18 | 0x8402);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_DATA_REG, register18 | 511);
+ et131x_mii_write(adapter, phydev->addr,
+ PHY_MPHY_CONTROL_REG, register18);
}
/* Free the packets being actively sent & stopped */
@@ -4644,10 +4631,6 @@
/* Copy address into the net_device struct */
memcpy(netdev->dev_addr, adapter->addr, ETH_ALEN);
- /* Init variable for counting how long we do not have link status */
- adapter->boot_coma = 0;
- et1310_disable_phy_coma(adapter);
-
rc = -ENOMEM;
/* Setup the mii_bus struct */
@@ -4663,7 +4646,6 @@
adapter->mii_bus->priv = netdev;
adapter->mii_bus->read = et131x_mdio_read;
adapter->mii_bus->write = et131x_mdio_write;
- adapter->mii_bus->reset = et131x_mdio_reset;
adapter->mii_bus->irq = kmalloc_array(PHY_MAX_ADDR, sizeof(int),
GFP_KERNEL);
if (!adapter->mii_bus->irq)
@@ -4687,6 +4669,10 @@
/* Setup et1310 as per the documentation */
et131x_adapter_setup(adapter);
+ /* Init variable for counting how long we do not have link status */
+ adapter->boot_coma = 0;
+ et1310_disable_phy_coma(adapter);
+
/* We can enable interrupts now
*
* NOTE - Because registration of interrupt handler is done in the
diff --git a/drivers/staging/lustre/lustre/libcfs/workitem.c b/drivers/staging/lustre/lustre/libcfs/workitem.c
index 6562957..03ab9e0 100644
--- a/drivers/staging/lustre/lustre/libcfs/workitem.c
+++ b/drivers/staging/lustre/lustre/libcfs/workitem.c
@@ -365,6 +365,7 @@
return -ENOMEM;
strncpy(sched->ws_name, name, CFS_WS_NAME_LEN);
+ sched->ws_name[CFS_WS_NAME_LEN - 1] = '\0';
sched->ws_cptab = cptab;
sched->ws_cpt = cpt;
diff --git a/drivers/staging/lustre/lustre/obdclass/class_obd.c b/drivers/staging/lustre/lustre/obdclass/class_obd.c
index 8b19f3c..701c6a7 100644
--- a/drivers/staging/lustre/lustre/obdclass/class_obd.c
+++ b/drivers/staging/lustre/lustre/obdclass/class_obd.c
@@ -35,7 +35,7 @@
*/
#define DEBUG_SUBSYSTEM S_CLASS
-# include <asm/atomic.h>
+# include <linux/atomic.h>
#include "../include/obd_support.h"
#include "../include/obd_class.h"
diff --git a/drivers/staging/rtl8188eu/os_dep/usb_intf.c b/drivers/staging/rtl8188eu/os_dep/usb_intf.c
index b8676ac..407a318 100644
--- a/drivers/staging/rtl8188eu/os_dep/usb_intf.c
+++ b/drivers/staging/rtl8188eu/os_dep/usb_intf.c
@@ -43,9 +43,11 @@
{USB_DEVICE(USB_VENDER_ID_REALTEK, 0x0179)}, /* 8188ETV */
/*=== Customer ID ===*/
/****** 8188EUS ********/
+ {USB_DEVICE(0x056e, 0x4008)}, /* Elecom WDC-150SU2M */
{USB_DEVICE(0x07b8, 0x8179)}, /* Abocom - Abocom */
{USB_DEVICE(0x2001, 0x330F)}, /* DLink DWA-125 REV D1 */
{USB_DEVICE(0x2001, 0x3310)}, /* Dlink DWA-123 REV D1 */
+ {USB_DEVICE(0x0df6, 0x0076)}, /* Sitecom N150 v2 */
{} /* Terminating entry */
};
diff --git a/drivers/thunderbolt/path.c b/drivers/thunderbolt/path.c
index 8fcf8a7..9562cd0 100644
--- a/drivers/thunderbolt/path.c
+++ b/drivers/thunderbolt/path.c
@@ -150,7 +150,26 @@
/* Activate hops. */
for (i = path->path_length - 1; i >= 0; i--) {
- struct tb_regs_hop hop;
+ struct tb_regs_hop hop = { 0 };
+
+ /*
+ * We do (currently) not tear down paths setup by the firmeware.
+ * If a firmware device is unplugged and plugged in again then
+ * it can happen that we reuse some of the hops from the (now
+ * defunct) firmeware path. This causes the hotplug operation to
+ * fail (the pci device does not show up). Clearing the hop
+ * before overwriting it fixes the problem.
+ *
+ * Should be removed once we discover and tear down firmeware
+ * paths.
+ */
+ res = tb_port_write(path->hops[i].in_port, &hop, TB_CFG_HOPS,
+ 2 * path->hops[i].in_hop_index, 2);
+ if (res) {
+ __tb_path_deactivate_hops(path, i);
+ __tb_path_deallocate_nfc(path, 0);
+ goto err;
+ }
/* dword 0 */
hop.next_hop = path->hops[i].next_hop_index;
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index e0cad44..cf1b19b 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -92,6 +92,8 @@
source "drivers/usb/image/Kconfig"
+source "drivers/usb/usbip/Kconfig"
+
endif
source "drivers/usb/musb/Kconfig"
diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
index 3cba892..d7be717 100644
--- a/drivers/usb/Makefile
+++ b/drivers/usb/Makefile
@@ -60,3 +60,5 @@
obj-$(CONFIG_USB_GADGET) += gadget/
obj-$(CONFIG_USB_COMMON) += common/
+
+obj-$(CONFIG_USBIP_CORE) += usbip/
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 8a4dcbc..46f5161 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1728,8 +1728,14 @@
* - Change autosuspend delay of hub can avoid unnecessary auto
* suspend timer for hub, also may decrease power consumption
* of USB bus.
+ *
+ * - If user has indicated to prevent autosuspend by passing
+ * usbcore.autosuspend = -1 then keep autosuspend disabled.
*/
- pm_runtime_set_autosuspend_delay(&hdev->dev, 0);
+#ifdef CONFIG_PM_RUNTIME
+ if (hdev->dev.power.autosuspend_delay >= 0)
+ pm_runtime_set_autosuspend_delay(&hdev->dev, 0);
+#endif
/*
* Hubs have proper suspend/resume support, except for root hubs
@@ -2107,8 +2113,8 @@
{
struct usb_port *port_dev = NULL;
struct usb_device *udev = *pdev;
- struct usb_hub *hub;
- int port1;
+ struct usb_hub *hub = NULL;
+ int port1 = 1;
/* mark the device as inactive, so any further urb submissions for
* this device (and any of its children) will fail immediately.
@@ -4631,9 +4637,7 @@
if (status != -ENODEV &&
port1 != unreliable_port &&
printk_ratelimit())
- dev_err(&udev->dev, "connect-debounce failed, port %d disabled\n",
- port1);
-
+ dev_err(&port_dev->dev, "connect-debounce failed\n");
portstatus &= ~USB_PORT_STAT_CONNECTION;
unreliable_port = port1;
} else {
diff --git a/drivers/usb/dwc2/gadget.c b/drivers/usb/dwc2/gadget.c
index 0ba9c33..7c9618e 100644
--- a/drivers/usb/dwc2/gadget.c
+++ b/drivers/usb/dwc2/gadget.c
@@ -1901,7 +1901,7 @@
static void s3c_hsotg_irq_enumdone(struct s3c_hsotg *hsotg)
{
u32 dsts = readl(hsotg->regs + DSTS);
- int ep0_mps = 0, ep_mps;
+ int ep0_mps = 0, ep_mps = 8;
/*
* This should signal the finish of the enumeration phase
diff --git a/drivers/usb/dwc3/dwc3-omap.c b/drivers/usb/dwc3/dwc3-omap.c
index ef4936f..9dcfbe7 100644
--- a/drivers/usb/dwc3/dwc3-omap.c
+++ b/drivers/usb/dwc3/dwc3-omap.c
@@ -425,7 +425,7 @@
static int dwc3_omap_extcon_register(struct dwc3_omap *omap)
{
- u32 ret;
+ int ret;
struct device_node *node = omap->dev->of_node;
struct extcon_dev *edev;
diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile
index a186afe..9add915 100644
--- a/drivers/usb/gadget/Makefile
+++ b/drivers/usb/gadget/Makefile
@@ -3,7 +3,7 @@
#
subdir-ccflags-$(CONFIG_USB_GADGET_DEBUG) := -DDEBUG
subdir-ccflags-$(CONFIG_USB_GADGET_VERBOSE) += -DVERBOSE_DEBUG
-ccflags-y += -I$(PWD)/drivers/usb/gadget/udc
+ccflags-y += -Idrivers/usb/gadget/udc
obj-$(CONFIG_USB_LIBCOMPOSITE) += libcomposite.o
libcomposite-y := usbstring.o config.o epautoconf.o
diff --git a/drivers/usb/gadget/function/Makefile b/drivers/usb/gadget/function/Makefile
index 6d91f21..83ae106 100644
--- a/drivers/usb/gadget/function/Makefile
+++ b/drivers/usb/gadget/function/Makefile
@@ -2,8 +2,8 @@
# USB peripheral controller drivers
#
-ccflags-y := -I$(PWD)/drivers/usb/gadget/
-ccflags-y += -I$(PWD)/drivers/usb/gadget/udc/
+ccflags-y := -Idrivers/usb/gadget/
+ccflags-y += -Idrivers/usb/gadget/udc/
# USB Functions
usb_f_acm-y := f_acm.o
diff --git a/drivers/usb/gadget/function/u_ether.c b/drivers/usb/gadget/function/u_ether.c
index d50adda..6e6f876 100644
--- a/drivers/usb/gadget/function/u_ether.c
+++ b/drivers/usb/gadget/function/u_ether.c
@@ -1127,10 +1127,7 @@
DBG(dev, "%s\n", __func__);
- netif_tx_lock(dev->net);
netif_stop_queue(dev->net);
- netif_tx_unlock(dev->net);
-
netif_carrier_off(dev->net);
/* disable endpoints, forcing (synchronous) completion
diff --git a/drivers/usb/gadget/function/uvc_video.c b/drivers/usb/gadget/function/uvc_video.c
index 71e896d..a5eb9a3 100644
--- a/drivers/usb/gadget/function/uvc_video.c
+++ b/drivers/usb/gadget/function/uvc_video.c
@@ -195,6 +195,7 @@
printk(KERN_INFO "Failed to queue request (%d).\n", ret);
usb_ep_set_halt(ep);
spin_unlock_irqrestore(&video->queue.irqlock, flags);
+ uvc_queue_cancel(queue, 0);
goto requeue;
}
spin_unlock_irqrestore(&video->queue.irqlock, flags);
@@ -281,6 +282,7 @@
static int
uvc_video_pump(struct uvc_video *video)
{
+ struct uvc_video_queue *queue = &video->queue;
struct usb_request *req;
struct uvc_buffer *buf;
unsigned long flags;
@@ -322,6 +324,7 @@
printk(KERN_INFO "Failed to queue request (%d)\n", ret);
usb_ep_set_halt(video->ep);
spin_unlock_irqrestore(&video->queue.irqlock, flags);
+ uvc_queue_cancel(queue, 0);
break;
}
spin_unlock_irqrestore(&video->queue.irqlock, flags);
diff --git a/drivers/usb/gadget/legacy/Makefile b/drivers/usb/gadget/legacy/Makefile
index a11aad5..edba2d1 100644
--- a/drivers/usb/gadget/legacy/Makefile
+++ b/drivers/usb/gadget/legacy/Makefile
@@ -2,9 +2,9 @@
# USB gadget drivers
#
-ccflags-y := -I$(PWD)/drivers/usb/gadget/
-ccflags-y += -I$(PWD)/drivers/usb/gadget/udc/
-ccflags-y += -I$(PWD)/drivers/usb/gadget/function/
+ccflags-y := -Idrivers/usb/gadget/
+ccflags-y += -Idrivers/usb/gadget/udc/
+ccflags-y += -Idrivers/usb/gadget/function/
g_zero-y := zero.o
g_audio-y := audio.o
diff --git a/drivers/usb/gadget/legacy/dbgp.c b/drivers/usb/gadget/legacy/dbgp.c
index 986fc51..225e385 100644
--- a/drivers/usb/gadget/legacy/dbgp.c
+++ b/drivers/usb/gadget/legacy/dbgp.c
@@ -222,10 +222,12 @@
{
#ifdef CONFIG_USB_G_DBGP_SERIAL
kfree(dbgp.serial);
+ dbgp.serial = NULL;
#endif
if (dbgp.req) {
kfree(dbgp.req->buf);
usb_ep_free_request(gadget->ep0, dbgp.req);
+ dbgp.req = NULL;
}
gadget->ep0->driver_data = NULL;
diff --git a/drivers/usb/gadget/legacy/inode.c b/drivers/usb/gadget/legacy/inode.c
index 2e4ce77..e96077b 100644
--- a/drivers/usb/gadget/legacy/inode.c
+++ b/drivers/usb/gadget/legacy/inode.c
@@ -440,7 +440,7 @@
value = -ENOMEM;
kbuf = memdup_user(buf, len);
- if (!kbuf) {
+ if (IS_ERR(kbuf)) {
value = PTR_ERR(kbuf);
goto free1;
}
diff --git a/drivers/usb/gadget/udc/Kconfig b/drivers/usb/gadget/udc/Kconfig
index 5151f94..34ebaa6 100644
--- a/drivers/usb/gadget/udc/Kconfig
+++ b/drivers/usb/gadget/udc/Kconfig
@@ -332,7 +332,7 @@
gadget drivers to also be dynamically linked.
config USB_EG20T
- tristate "Intel EG20T PCH/LAPIS Semiconductor IOH(ML7213/ML7831) UDC"
+ tristate "Intel QUARK X1000/EG20T PCH/LAPIS Semiconductor IOH(ML7213/ML7831) UDC"
depends on PCI
help
This is a USB device driver for EG20T PCH.
@@ -353,6 +353,7 @@
ML7213/ML7831 is companion chip for Intel Atom E6xx series.
ML7213/ML7831 is completely compatible for Intel EG20T PCH.
+ This driver can be used with Intel's Quark X1000 SOC platform
#
# LAST -- dummy/emulated controller
#
diff --git a/drivers/usb/gadget/udc/atmel_usba_udc.c b/drivers/usb/gadget/udc/atmel_usba_udc.c
index 906e65f..c9fe67e 100644
--- a/drivers/usb/gadget/udc/atmel_usba_udc.c
+++ b/drivers/usb/gadget/udc/atmel_usba_udc.c
@@ -1661,7 +1661,7 @@
if (dma_status) {
int i;
- for (i = 1; i < USBA_NR_DMAS; i++)
+ for (i = 1; i <= USBA_NR_DMAS; i++)
if (dma_status & (1 << i))
usba_dma_irq(udc, &udc->usba_ep[i]);
}
diff --git a/drivers/usb/gadget/udc/fusb300_udc.c b/drivers/usb/gadget/udc/fusb300_udc.c
index d40255f..5c5d1ad 100644
--- a/drivers/usb/gadget/udc/fusb300_udc.c
+++ b/drivers/usb/gadget/udc/fusb300_udc.c
@@ -1398,13 +1398,17 @@
/* initialize udc */
fusb300 = kzalloc(sizeof(struct fusb300), GFP_KERNEL);
- if (fusb300 == NULL)
+ if (fusb300 == NULL) {
+ ret = -ENOMEM;
goto clean_up;
+ }
for (i = 0; i < FUSB300_MAX_NUM_EP; i++) {
_ep[i] = kzalloc(sizeof(struct fusb300_ep), GFP_KERNEL);
- if (_ep[i] == NULL)
+ if (_ep[i] == NULL) {
+ ret = -ENOMEM;
goto clean_up;
+ }
fusb300->ep[i] = _ep[i];
}
diff --git a/drivers/usb/gadget/udc/pch_udc.c b/drivers/usb/gadget/udc/pch_udc.c
index eb8c3be..460d953 100644
--- a/drivers/usb/gadget/udc/pch_udc.c
+++ b/drivers/usb/gadget/udc/pch_udc.c
@@ -343,6 +343,7 @@
* @setup_data: Received setup data
* @phys_addr: of device memory
* @base_addr: for mapped device memory
+ * @bar: Indicates which PCI BAR for USB regs
* @irq: IRQ line for the device
* @cfg_data: current cfg, intf, and alt in use
* @vbus_gpio: GPIO informaton for detecting VBUS
@@ -370,14 +371,17 @@
struct usb_ctrlrequest setup_data;
unsigned long phys_addr;
void __iomem *base_addr;
+ unsigned bar;
unsigned irq;
struct pch_udc_cfg_data cfg_data;
struct pch_vbus_gpio_data vbus_gpio;
};
#define to_pch_udc(g) (container_of((g), struct pch_udc_dev, gadget))
+#define PCH_UDC_PCI_BAR_QUARK_X1000 0
#define PCH_UDC_PCI_BAR 1
#define PCI_DEVICE_ID_INTEL_EG20T_UDC 0x8808
+#define PCI_DEVICE_ID_INTEL_QUARK_X1000_UDC 0x0939
#define PCI_VENDOR_ID_ROHM 0x10DB
#define PCI_DEVICE_ID_ML7213_IOH_UDC 0x801D
#define PCI_DEVICE_ID_ML7831_IOH_UDC 0x8808
@@ -3076,7 +3080,7 @@
iounmap(dev->base_addr);
if (dev->mem_region)
release_mem_region(dev->phys_addr,
- pci_resource_len(pdev, PCH_UDC_PCI_BAR));
+ pci_resource_len(pdev, dev->bar));
if (dev->active)
pci_disable_device(pdev);
kfree(dev);
@@ -3144,9 +3148,15 @@
dev->active = 1;
pci_set_drvdata(pdev, dev);
+ /* Determine BAR based on PCI ID */
+ if (id->device == PCI_DEVICE_ID_INTEL_QUARK_X1000_UDC)
+ dev->bar = PCH_UDC_PCI_BAR_QUARK_X1000;
+ else
+ dev->bar = PCH_UDC_PCI_BAR;
+
/* PCI resource allocation */
- resource = pci_resource_start(pdev, 1);
- len = pci_resource_len(pdev, 1);
+ resource = pci_resource_start(pdev, dev->bar);
+ len = pci_resource_len(pdev, dev->bar);
if (!request_mem_region(resource, len, KBUILD_MODNAME)) {
dev_err(&pdev->dev, "%s: pci device used already\n", __func__);
@@ -3212,6 +3222,12 @@
static const struct pci_device_id pch_udc_pcidev_id[] = {
{
+ PCI_DEVICE(PCI_VENDOR_ID_INTEL,
+ PCI_DEVICE_ID_INTEL_QUARK_X1000_UDC),
+ .class = (PCI_CLASS_SERIAL_USB << 8) | 0xfe,
+ .class_mask = 0xffffffff,
+ },
+ {
PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EG20T_UDC),
.class = (PCI_CLASS_SERIAL_USB << 8) | 0xfe,
.class_mask = 0xffffffff,
diff --git a/drivers/usb/gadget/udc/r8a66597-udc.c b/drivers/usb/gadget/udc/r8a66597-udc.c
index 4600842..de2a871 100644
--- a/drivers/usb/gadget/udc/r8a66597-udc.c
+++ b/drivers/usb/gadget/udc/r8a66597-udc.c
@@ -1868,8 +1868,8 @@
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
reg = devm_ioremap_resource(&pdev->dev, res);
- if (!reg)
- return -ENODEV;
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
ires = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
irq = ires->start;
diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c
index cc305c7..6130b75 100644
--- a/drivers/usb/host/ehci-hub.c
+++ b/drivers/usb/host/ehci-hub.c
@@ -1230,7 +1230,7 @@
if (selector == EHSET_TEST_SINGLE_STEP_SET_FEATURE) {
spin_unlock_irqrestore(&ehci->lock, flags);
retval = ehset_single_step_set_feature(hcd,
- wIndex);
+ wIndex + 1);
spin_lock_irqsave(&ehci->lock, flags);
break;
}
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
index 687d366..c22a3e1 100644
--- a/drivers/usb/host/xhci-pci.c
+++ b/drivers/usb/host/xhci-pci.c
@@ -101,6 +101,10 @@
/* AMD PLL quirk */
if (pdev->vendor == PCI_VENDOR_ID_AMD && usb_amd_find_chipset_info())
xhci->quirks |= XHCI_AMD_PLL_FIX;
+
+ if (pdev->vendor == PCI_VENDOR_ID_AMD)
+ xhci->quirks |= XHCI_TRUST_TX_LENGTH;
+
if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
xhci->quirks |= XHCI_LPM_SUPPORT;
xhci->quirks |= XHCI_INTEL_HOST;
@@ -151,6 +155,11 @@
if (pdev->vendor == PCI_VENDOR_ID_VIA)
xhci->quirks |= XHCI_RESET_ON_RESUME;
+ /* See https://bugzilla.kernel.org/show_bug.cgi?id=79511 */
+ if (pdev->vendor == PCI_VENDOR_ID_VIA &&
+ pdev->device == 0x3432)
+ xhci->quirks |= XHCI_BROKEN_STREAMS;
+
if (xhci->quirks & XHCI_RESET_ON_RESUME)
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"QUIRK: Resetting on resume");
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 60fb52a..abed30b 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -364,32 +364,6 @@
}
}
-/*
- * Find the segment that trb is in. Start searching in start_seg.
- * If we must move past a segment that has a link TRB with a toggle cycle state
- * bit set, then we will toggle the value pointed at by cycle_state.
- */
-static struct xhci_segment *find_trb_seg(
- struct xhci_segment *start_seg,
- union xhci_trb *trb, int *cycle_state)
-{
- struct xhci_segment *cur_seg = start_seg;
- struct xhci_generic_trb *generic_trb;
-
- while (cur_seg->trbs > trb ||
- &cur_seg->trbs[TRBS_PER_SEGMENT - 1] < trb) {
- generic_trb = &cur_seg->trbs[TRBS_PER_SEGMENT - 1].generic;
- if (generic_trb->field[3] & cpu_to_le32(LINK_TOGGLE))
- *cycle_state ^= 0x1;
- cur_seg = cur_seg->next;
- if (cur_seg == start_seg)
- /* Looped over the entire list. Oops! */
- return NULL;
- }
- return cur_seg;
-}
-
-
static struct xhci_ring *xhci_triad_to_transfer_ring(struct xhci_hcd *xhci,
unsigned int slot_id, unsigned int ep_index,
unsigned int stream_id)
@@ -459,9 +433,12 @@
struct xhci_virt_device *dev = xhci->devs[slot_id];
struct xhci_virt_ep *ep = &dev->eps[ep_index];
struct xhci_ring *ep_ring;
- struct xhci_generic_trb *trb;
+ struct xhci_segment *new_seg;
+ union xhci_trb *new_deq;
dma_addr_t addr;
u64 hw_dequeue;
+ bool cycle_found = false;
+ bool td_last_trb_found = false;
ep_ring = xhci_triad_to_transfer_ring(xhci, slot_id,
ep_index, stream_id);
@@ -486,45 +463,45 @@
hw_dequeue = le64_to_cpu(ep_ctx->deq);
}
- /* Find virtual address and segment of hardware dequeue pointer */
- state->new_deq_seg = ep_ring->deq_seg;
- state->new_deq_ptr = ep_ring->dequeue;
- while (xhci_trb_virt_to_dma(state->new_deq_seg, state->new_deq_ptr)
- != (dma_addr_t)(hw_dequeue & ~0xf)) {
- next_trb(xhci, ep_ring, &state->new_deq_seg,
- &state->new_deq_ptr);
- if (state->new_deq_ptr == ep_ring->dequeue) {
- WARN_ON(1);
+ new_seg = ep_ring->deq_seg;
+ new_deq = ep_ring->dequeue;
+ state->new_cycle_state = hw_dequeue & 0x1;
+
+ /*
+ * We want to find the pointer, segment and cycle state of the new trb
+ * (the one after current TD's last_trb). We know the cycle state at
+ * hw_dequeue, so walk the ring until both hw_dequeue and last_trb are
+ * found.
+ */
+ do {
+ if (!cycle_found && xhci_trb_virt_to_dma(new_seg, new_deq)
+ == (dma_addr_t)(hw_dequeue & ~0xf)) {
+ cycle_found = true;
+ if (td_last_trb_found)
+ break;
+ }
+ if (new_deq == cur_td->last_trb)
+ td_last_trb_found = true;
+
+ if (cycle_found &&
+ TRB_TYPE_LINK_LE32(new_deq->generic.field[3]) &&
+ new_deq->generic.field[3] & cpu_to_le32(LINK_TOGGLE))
+ state->new_cycle_state ^= 0x1;
+
+ next_trb(xhci, ep_ring, &new_seg, &new_deq);
+
+ /* Search wrapped around, bail out */
+ if (new_deq == ep->ring->dequeue) {
+ xhci_err(xhci, "Error: Failed finding new dequeue state\n");
+ state->new_deq_seg = NULL;
+ state->new_deq_ptr = NULL;
return;
}
- }
- /*
- * Find cycle state for last_trb, starting at old cycle state of
- * hw_dequeue. If there is only one segment ring, find_trb_seg() will
- * return immediately and cannot toggle the cycle state if this search
- * wraps around, so add one more toggle manually in that case.
- */
- state->new_cycle_state = hw_dequeue & 0x1;
- if (ep_ring->first_seg == ep_ring->first_seg->next &&
- cur_td->last_trb < state->new_deq_ptr)
- state->new_cycle_state ^= 0x1;
- state->new_deq_ptr = cur_td->last_trb;
- xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb,
- "Finding segment containing last TRB in TD.");
- state->new_deq_seg = find_trb_seg(state->new_deq_seg,
- state->new_deq_ptr, &state->new_cycle_state);
- if (!state->new_deq_seg) {
- WARN_ON(1);
- return;
- }
+ } while (!cycle_found || !td_last_trb_found);
- /* Increment to find next TRB after last_trb. Cycle if appropriate. */
- trb = &state->new_deq_ptr->generic;
- if (TRB_TYPE_LINK_LE32(trb->field[3]) &&
- (trb->field[3] & cpu_to_le32(LINK_TOGGLE)))
- state->new_cycle_state ^= 0x1;
- next_trb(xhci, ep_ring, &state->new_deq_seg, &state->new_deq_ptr);
+ state->new_deq_seg = new_seg;
+ state->new_deq_ptr = new_deq;
/* Don't update the ring cycle state for the producer (us). */
xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb,
@@ -2487,7 +2464,8 @@
* last TRB of the previous TD. The command completion handle
* will take care the rest.
*/
- if (!event_seg && trb_comp_code == COMP_STOP_INVAL) {
+ if (!event_seg && (trb_comp_code == COMP_STOP ||
+ trb_comp_code == COMP_STOP_INVAL)) {
ret = 0;
goto cleanup;
}
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index b6f2117..c020b09 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -2880,6 +2880,9 @@
ep_index, ep->stopped_stream, ep->stopped_td,
&deq_state);
+ if (!deq_state.new_deq_ptr || !deq_state.new_deq_seg)
+ return;
+
/* HW with the reset endpoint quirk will use the saved dequeue state to
* issue a configure endpoint command later.
*/
diff --git a/drivers/usb/misc/sisusbvga/sisusb.c b/drivers/usb/misc/sisusbvga/sisusb.c
index 06b5d77..633caf6 100644
--- a/drivers/usb/misc/sisusbvga/sisusb.c
+++ b/drivers/usb/misc/sisusbvga/sisusb.c
@@ -3250,6 +3250,7 @@
{ USB_DEVICE(0x0711, 0x0918) },
{ USB_DEVICE(0x0711, 0x0920) },
{ USB_DEVICE(0x0711, 0x0950) },
+ { USB_DEVICE(0x0711, 0x5200) },
{ USB_DEVICE(0x182d, 0x021c) },
{ USB_DEVICE(0x182d, 0x0269) },
{ }
diff --git a/drivers/usb/musb/ux500_dma.c b/drivers/usb/musb/ux500_dma.c
index 9aad00f..221faed 100644
--- a/drivers/usb/musb/ux500_dma.c
+++ b/drivers/usb/musb/ux500_dma.c
@@ -96,7 +96,7 @@
struct musb *musb = ux500_channel->controller->private_data;
dev_dbg(musb->controller,
- "packet_sz=%d, mode=%d, dma_addr=0x%llu, len=%d is_tx=%d\n",
+ "packet_sz=%d, mode=%d, dma_addr=0x%llx, len=%d is_tx=%d\n",
packet_sz, mode, (unsigned long long) dma_addr,
len, ux500_channel->is_tx);
diff --git a/drivers/usb/phy/phy-gpio-vbus-usb.c b/drivers/usb/phy/phy-gpio-vbus-usb.c
index ea9e705..f4b14bd 100644
--- a/drivers/usb/phy/phy-gpio-vbus-usb.c
+++ b/drivers/usb/phy/phy-gpio-vbus-usb.c
@@ -260,10 +260,8 @@
gpio_vbus->phy.otg = devm_kzalloc(&pdev->dev, sizeof(struct usb_otg),
GFP_KERNEL);
- if (!gpio_vbus->phy.otg) {
- kfree(gpio_vbus);
+ if (!gpio_vbus->phy.otg)
return -ENOMEM;
- }
platform_set_drvdata(pdev, gpio_vbus);
gpio_vbus->dev = &pdev->dev;
diff --git a/drivers/usb/phy/phy-msm-usb.c b/drivers/usb/phy/phy-msm-usb.c
index e4108ee..afc0908 100644
--- a/drivers/usb/phy/phy-msm-usb.c
+++ b/drivers/usb/phy/phy-msm-usb.c
@@ -1601,8 +1601,8 @@
*/
if (motg->phy_number) {
phy_select = devm_ioremap_nocache(&pdev->dev, USB2_PHY_SEL, 4);
- if (IS_ERR(phy_select))
- return PTR_ERR(phy_select);
+ if (!phy_select)
+ return -ENOMEM;
/* Enable second PHY with the OTG port */
writel(0x1, phy_select);
}
diff --git a/drivers/usb/phy/phy-samsung-usb.h b/drivers/usb/phy/phy-samsung-usb.h
index 68771bf..80eedd4 100644
--- a/drivers/usb/phy/phy-samsung-usb.h
+++ b/drivers/usb/phy/phy-samsung-usb.h
@@ -216,7 +216,7 @@
#define EXYNOS5_DRD_PHYPARAM1 (0x20)
-#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
+#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x3f << 0)
#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
#define EXYNOS5_DRD_PHYTERM (0x24)
diff --git a/drivers/usb/phy/phy.c b/drivers/usb/phy/phy.c
index 6d0f608..045cd30 100644
--- a/drivers/usb/phy/phy.c
+++ b/drivers/usb/phy/phy.c
@@ -232,6 +232,9 @@
phy = __usb_find_phy_dev(dev, &phy_bind_list, index);
if (IS_ERR(phy) || !try_module_get(phy->dev->driver->owner)) {
dev_dbg(dev, "unable to find transceiver\n");
+ if (!IS_ERR(phy))
+ phy = ERR_PTR(-ENODEV);
+
goto err0;
}
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 216ce30..824ea5e 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -146,6 +146,7 @@
{ USB_DEVICE(FTDI_VID, FTDI_AMC232_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CANUSB_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CANDAPTER_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_BM_ATOM_NANO_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_NXTCAM_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_EV3CON_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_0_PID) },
@@ -934,6 +935,8 @@
{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_842_2_PID) },
{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_842_3_PID) },
{ USB_DEVICE(BRAINBOXES_VID, BRAINBOXES_US_842_4_PID) },
+ /* ekey Devices */
+ { USB_DEVICE(FTDI_VID, FTDI_EKEY_CONV_USB_PID) },
/* Infineon Devices */
{ USB_DEVICE_INTERFACE_NUMBER(INFINEON_VID, INFINEON_TRIBOARD_PID, 1) },
{ } /* Terminating entry */
diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h
index 1e58d90..70b0b1d 100644
--- a/drivers/usb/serial/ftdi_sio_ids.h
+++ b/drivers/usb/serial/ftdi_sio_ids.h
@@ -42,6 +42,8 @@
/* www.candapter.com Ewert Energy Systems CANdapter device */
#define FTDI_CANDAPTER_PID 0x9F80 /* Product Id */
+#define FTDI_BM_ATOM_NANO_PID 0xa559 /* Basic Micro ATOM Nano USB2Serial */
+
/*
* Texas Instruments XDS100v2 JTAG / BeagleBone A3
* http://processors.wiki.ti.com/index.php/XDS100
@@ -1378,3 +1380,8 @@
#define BRAINBOXES_US_160_6_PID 0x9006 /* US-160 16xRS232 1Mbaud Port 11 and 12 */
#define BRAINBOXES_US_160_7_PID 0x9007 /* US-160 16xRS232 1Mbaud Port 13 and 14 */
#define BRAINBOXES_US_160_8_PID 0x9008 /* US-160 16xRS232 1Mbaud Port 15 and 16 */
+
+/*
+ * ekey biometric systems GmbH (http://ekey.net/)
+ */
+#define FTDI_EKEY_CONV_USB_PID 0xCB08 /* Converter USB */
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index a968894..54a8120 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -275,8 +275,12 @@
#define ZTE_PRODUCT_MF622 0x0001
#define ZTE_PRODUCT_MF628 0x0015
#define ZTE_PRODUCT_MF626 0x0031
-#define ZTE_PRODUCT_MC2718 0xffe8
#define ZTE_PRODUCT_AC2726 0xfff1
+#define ZTE_PRODUCT_CDMA_TECH 0xfffe
+#define ZTE_PRODUCT_AC8710T 0xffff
+#define ZTE_PRODUCT_MC2718 0xffe8
+#define ZTE_PRODUCT_AD3812 0xffeb
+#define ZTE_PRODUCT_MC2716 0xffed
#define BENQ_VENDOR_ID 0x04a5
#define BENQ_PRODUCT_H10 0x4068
@@ -494,6 +498,10 @@
#define INOVIA_VENDOR_ID 0x20a6
#define INOVIA_SEW858 0x1105
+/* VIA Telecom */
+#define VIATELECOM_VENDOR_ID 0x15eb
+#define VIATELECOM_PRODUCT_CDS7 0x0001
+
/* some devices interfaces need special handling due to a number of reasons */
enum option_blacklist_reason {
OPTION_BLACKLIST_NONE = 0,
@@ -527,10 +535,18 @@
.reserved = BIT(4),
};
+static const struct option_blacklist_info zte_ad3812_z_blacklist = {
+ .sendsetup = BIT(0) | BIT(1) | BIT(2),
+};
+
static const struct option_blacklist_info zte_mc2718_z_blacklist = {
.sendsetup = BIT(1) | BIT(2) | BIT(3) | BIT(4),
};
+static const struct option_blacklist_info zte_mc2716_z_blacklist = {
+ .sendsetup = BIT(1) | BIT(2) | BIT(3),
+};
+
static const struct option_blacklist_info huawei_cdc12_blacklist = {
.reserved = BIT(1) | BIT(2),
};
@@ -1070,6 +1086,7 @@
{ USB_DEVICE_INTERFACE_CLASS(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1012, 0xff) },
{ USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC650) },
{ USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC680) },
+ { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6000)}, /* ZTE AC8700 */
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6613)}, /* Onda H600/ZTE MF330 */
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x0023)}, /* ONYX 3G device */
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x9000)}, /* SIMCom SIM5218 */
@@ -1544,13 +1561,18 @@
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff93, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff94, 0xff, 0xff, 0xff) },
- /* NOTE: most ZTE CDMA devices should be driven by zte_ev, not option */
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) },
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC2726, 0xff, 0xff, 0xff) },
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710T, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2718, 0xff, 0xff, 0xff),
.driver_info = (kernel_ulong_t)&zte_mc2718_z_blacklist },
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AD3812, 0xff, 0xff, 0xff),
+ .driver_info = (kernel_ulong_t)&zte_ad3812_z_blacklist },
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2716, 0xff, 0xff, 0xff),
+ .driver_info = (kernel_ulong_t)&zte_mc2716_z_blacklist },
{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x01) },
{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x05) },
{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x86, 0x10) },
- { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC2726, 0xff, 0xff, 0xff) },
{ USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) },
{ USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) },
@@ -1724,6 +1746,7 @@
{ USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e01, 0xff, 0xff, 0xff) }, /* D-Link DWM-152/C1 */
{ USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e02, 0xff, 0xff, 0xff) }, /* D-Link DWM-156/C1 */
{ USB_DEVICE(INOVIA_VENDOR_ID, INOVIA_SEW858) },
+ { USB_DEVICE(VIATELECOM_VENDOR_ID, VIATELECOM_PRODUCT_CDS7) },
{ } /* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, option_ids);
@@ -1916,6 +1939,8 @@
dev_dbg(dev, "%s: type %x req %x\n", __func__,
req_pkt->bRequestType, req_pkt->bRequest);
}
+ } else if (status == -ENOENT || status == -ESHUTDOWN) {
+ dev_dbg(dev, "%s: urb stopped: %d\n", __func__, status);
} else
dev_err(dev, "%s: error %d\n", __func__, status);
diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index b3d5a35..e9bad92 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -45,6 +45,7 @@
{ USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_GPRS) },
{ USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_HCR331) },
{ USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_MOTOROLA) },
+ { USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_ZTEK) },
{ USB_DEVICE(IODATA_VENDOR_ID, IODATA_PRODUCT_ID) },
{ USB_DEVICE(IODATA_VENDOR_ID, IODATA_PRODUCT_ID_RSAQ5) },
{ USB_DEVICE(ATEN_VENDOR_ID, ATEN_PRODUCT_ID) },
diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h
index 42bc082..71fd9da 100644
--- a/drivers/usb/serial/pl2303.h
+++ b/drivers/usb/serial/pl2303.h
@@ -22,6 +22,7 @@
#define PL2303_PRODUCT_ID_GPRS 0x0609
#define PL2303_PRODUCT_ID_HCR331 0x331a
#define PL2303_PRODUCT_ID_MOTOROLA 0x0307
+#define PL2303_PRODUCT_ID_ZTEK 0xe1f1
#define ATEN_VENDOR_ID 0x0557
#define ATEN_VENDOR_ID2 0x0547
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index 02de311..475723c 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -764,29 +764,39 @@
if (usb_endpoint_is_bulk_in(endpoint)) {
/* we found a bulk in endpoint */
dev_dbg(ddev, "found bulk in on endpoint %d\n", i);
- bulk_in_endpoint[num_bulk_in] = endpoint;
- ++num_bulk_in;
+ if (num_bulk_in < MAX_NUM_PORTS) {
+ bulk_in_endpoint[num_bulk_in] = endpoint;
+ ++num_bulk_in;
+ }
}
if (usb_endpoint_is_bulk_out(endpoint)) {
/* we found a bulk out endpoint */
dev_dbg(ddev, "found bulk out on endpoint %d\n", i);
- bulk_out_endpoint[num_bulk_out] = endpoint;
- ++num_bulk_out;
+ if (num_bulk_out < MAX_NUM_PORTS) {
+ bulk_out_endpoint[num_bulk_out] = endpoint;
+ ++num_bulk_out;
+ }
}
if (usb_endpoint_is_int_in(endpoint)) {
/* we found a interrupt in endpoint */
dev_dbg(ddev, "found interrupt in on endpoint %d\n", i);
- interrupt_in_endpoint[num_interrupt_in] = endpoint;
- ++num_interrupt_in;
+ if (num_interrupt_in < MAX_NUM_PORTS) {
+ interrupt_in_endpoint[num_interrupt_in] =
+ endpoint;
+ ++num_interrupt_in;
+ }
}
if (usb_endpoint_is_int_out(endpoint)) {
/* we found an interrupt out endpoint */
dev_dbg(ddev, "found interrupt out on endpoint %d\n", i);
- interrupt_out_endpoint[num_interrupt_out] = endpoint;
- ++num_interrupt_out;
+ if (num_interrupt_out < MAX_NUM_PORTS) {
+ interrupt_out_endpoint[num_interrupt_out] =
+ endpoint;
+ ++num_interrupt_out;
+ }
}
}
@@ -809,8 +819,10 @@
if (usb_endpoint_is_int_in(endpoint)) {
/* we found a interrupt in endpoint */
dev_dbg(ddev, "found interrupt in for Prolific device on separate interface\n");
- interrupt_in_endpoint[num_interrupt_in] = endpoint;
- ++num_interrupt_in;
+ if (num_interrupt_in < MAX_NUM_PORTS) {
+ interrupt_in_endpoint[num_interrupt_in] = endpoint;
+ ++num_interrupt_in;
+ }
}
}
}
@@ -850,6 +862,11 @@
num_ports = type->num_ports;
}
+ if (num_ports > MAX_NUM_PORTS) {
+ dev_warn(ddev, "too many ports requested: %d\n", num_ports);
+ num_ports = MAX_NUM_PORTS;
+ }
+
serial->num_ports = num_ports;
serial->num_bulk_in = num_bulk_in;
serial->num_bulk_out = num_bulk_out;
diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c
index e62f2df..6c3734d 100644
--- a/drivers/usb/serial/whiteheat.c
+++ b/drivers/usb/serial/whiteheat.c
@@ -514,6 +514,10 @@
dev_dbg(&urb->dev->dev, "%s - command_info is NULL, exiting.\n", __func__);
return;
}
+ if (!urb->actual_length) {
+ dev_dbg(&urb->dev->dev, "%s - empty response, exiting.\n", __func__);
+ return;
+ }
if (status) {
dev_dbg(&urb->dev->dev, "%s - nonzero urb status: %d\n", __func__, status);
if (status != -ENOENT)
@@ -534,7 +538,8 @@
/* These are unsolicited reports from the firmware, hence no
waiting command to wakeup */
dev_dbg(&urb->dev->dev, "%s - event received\n", __func__);
- } else if (data[0] == WHITEHEAT_GET_DTR_RTS) {
+ } else if ((data[0] == WHITEHEAT_GET_DTR_RTS) &&
+ (urb->actual_length - 1 <= sizeof(command_info->result_buffer))) {
memcpy(command_info->result_buffer, &data[1],
urb->actual_length - 1);
command_info->command_finished = WHITEHEAT_CMD_COMPLETE;
diff --git a/drivers/usb/serial/zte_ev.c b/drivers/usb/serial/zte_ev.c
index e40ab73..1a132e9 100644
--- a/drivers/usb/serial/zte_ev.c
+++ b/drivers/usb/serial/zte_ev.c
@@ -272,28 +272,8 @@
}
static const struct usb_device_id id_table[] = {
- /* AC8710, AC8710T */
- { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffff, 0xff, 0xff, 0xff) },
- /* AC8700 */
- { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xfffe, 0xff, 0xff, 0xff) },
/* MG880 */
{ USB_DEVICE(0x19d2, 0xfffd) },
- { USB_DEVICE(0x19d2, 0xfffc) },
- { USB_DEVICE(0x19d2, 0xfffb) },
- /* AC8710_V3 */
- { USB_DEVICE(0x19d2, 0xfff6) },
- { USB_DEVICE(0x19d2, 0xfff7) },
- { USB_DEVICE(0x19d2, 0xfff8) },
- { USB_DEVICE(0x19d2, 0xfff9) },
- { USB_DEVICE(0x19d2, 0xffee) },
- /* AC2716, MC2716 */
- { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffed, 0xff, 0xff, 0xff) },
- /* AD3812 */
- { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffeb, 0xff, 0xff, 0xff) },
- { USB_DEVICE(0x19d2, 0xffec) },
- { USB_DEVICE(0x05C6, 0x3197) },
- { USB_DEVICE(0x05C6, 0x6000) },
- { USB_DEVICE(0x05C6, 0x9008) },
{ },
};
MODULE_DEVICE_TABLE(usb, id_table);
diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index 80a5b36..7ef99b2f 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -922,6 +922,12 @@
USB_SC_DEVICE, USB_PR_DEVICE, NULL,
US_FL_FIX_CAPACITY ),
+UNUSUAL_DEV( 0x06ca, 0x2003, 0x0100, 0x0100,
+ "Newer Technology",
+ "uSCSI",
+ USB_SC_DEVICE, USB_PR_DEVICE, usb_stor_euscsi_init,
+ US_FL_SCM_MULT_TARG ),
+
/* Reported by Adrian Pilchowiec <adi1981@epf.pl> */
UNUSUAL_DEV( 0x071b, 0x3203, 0x0000, 0x0000,
"RockChip",
diff --git a/drivers/staging/usbip/Kconfig b/drivers/usb/usbip/Kconfig
similarity index 100%
rename from drivers/staging/usbip/Kconfig
rename to drivers/usb/usbip/Kconfig
diff --git a/drivers/staging/usbip/Makefile b/drivers/usb/usbip/Makefile
similarity index 100%
rename from drivers/staging/usbip/Makefile
rename to drivers/usb/usbip/Makefile
diff --git a/drivers/staging/usbip/README b/drivers/usb/usbip/README
similarity index 100%
rename from drivers/staging/usbip/README
rename to drivers/usb/usbip/README
diff --git a/drivers/staging/usbip/stub.h b/drivers/usb/usbip/stub.h
similarity index 100%
rename from drivers/staging/usbip/stub.h
rename to drivers/usb/usbip/stub.h
diff --git a/drivers/staging/usbip/stub_dev.c b/drivers/usb/usbip/stub_dev.c
similarity index 90%
rename from drivers/staging/usbip/stub_dev.c
rename to drivers/usb/usbip/stub_dev.c
index 51d0c71..fac20e0 100644
--- a/drivers/staging/usbip/stub_dev.c
+++ b/drivers/usb/usbip/stub_dev.c
@@ -26,33 +26,6 @@
#include "stub.h"
/*
- * Define device IDs here if you want to explicitly limit exportable devices.
- * In most cases, wildcard matching will be okay because driver binding can be
- * changed dynamically by a userland program.
- */
-static struct usb_device_id stub_table[] = {
-#if 0
- /* just an example */
- { USB_DEVICE(0x05ac, 0x0301) }, /* Mac 1 button mouse */
- { USB_DEVICE(0x0430, 0x0009) }, /* Plat Home Keyboard */
- { USB_DEVICE(0x059b, 0x0001) }, /* Iomega USB Zip 100 */
- { USB_DEVICE(0x04b3, 0x4427) }, /* IBM USB CD-ROM */
- { USB_DEVICE(0x05a9, 0xa511) }, /* LifeView USB cam */
- { USB_DEVICE(0x55aa, 0x0201) }, /* Imation card reader */
- { USB_DEVICE(0x046d, 0x0870) }, /* Qcam Express(QV-30) */
- { USB_DEVICE(0x04bb, 0x0101) }, /* IO-DATA HD 120GB */
- { USB_DEVICE(0x04bb, 0x0904) }, /* IO-DATA USB-ET/TX */
- { USB_DEVICE(0x04bb, 0x0201) }, /* IO-DATA USB-ET/TX */
- { USB_DEVICE(0x08bb, 0x2702) }, /* ONKYO USB Speaker */
- { USB_DEVICE(0x046d, 0x08b2) }, /* Logicool Qcam 4000 Pro */
-#endif
- /* magic for wild card */
- { .driver_info = 1 },
- { 0, } /* Terminating entry */
-};
-MODULE_DEVICE_TABLE(usb, stub_table);
-
-/*
* usbip_status shows the status of usbip-host as long as this driver is bound
* to the target device.
*/
diff --git a/drivers/staging/usbip/stub_main.c b/drivers/usb/usbip/stub_main.c
similarity index 100%
rename from drivers/staging/usbip/stub_main.c
rename to drivers/usb/usbip/stub_main.c
diff --git a/drivers/staging/usbip/stub_rx.c b/drivers/usb/usbip/stub_rx.c
similarity index 100%
rename from drivers/staging/usbip/stub_rx.c
rename to drivers/usb/usbip/stub_rx.c
diff --git a/drivers/staging/usbip/stub_tx.c b/drivers/usb/usbip/stub_tx.c
similarity index 100%
rename from drivers/staging/usbip/stub_tx.c
rename to drivers/usb/usbip/stub_tx.c
diff --git a/drivers/staging/usbip/usbip_common.c b/drivers/usb/usbip/usbip_common.c
similarity index 100%
rename from drivers/staging/usbip/usbip_common.c
rename to drivers/usb/usbip/usbip_common.c
diff --git a/drivers/staging/usbip/usbip_common.h b/drivers/usb/usbip/usbip_common.h
similarity index 99%
rename from drivers/staging/usbip/usbip_common.h
rename to drivers/usb/usbip/usbip_common.h
index 4da3866..86b0847 100644
--- a/drivers/staging/usbip/usbip_common.h
+++ b/drivers/usb/usbip/usbip_common.h
@@ -29,7 +29,7 @@
#include <linux/types.h>
#include <linux/usb.h>
#include <linux/wait.h>
-#include "uapi/usbip.h"
+#include <uapi/linux/usbip.h>
#define USBIP_VERSION "1.0.0"
diff --git a/drivers/staging/usbip/usbip_event.c b/drivers/usb/usbip/usbip_event.c
similarity index 100%
rename from drivers/staging/usbip/usbip_event.c
rename to drivers/usb/usbip/usbip_event.c
diff --git a/drivers/staging/usbip/usbip_protocol.txt b/drivers/usb/usbip/usbip_protocol.txt
similarity index 100%
rename from drivers/staging/usbip/usbip_protocol.txt
rename to drivers/usb/usbip/usbip_protocol.txt
diff --git a/drivers/staging/usbip/vhci.h b/drivers/usb/usbip/vhci.h
similarity index 100%
rename from drivers/staging/usbip/vhci.h
rename to drivers/usb/usbip/vhci.h
diff --git a/drivers/staging/usbip/vhci_hcd.c b/drivers/usb/usbip/vhci_hcd.c
similarity index 100%
rename from drivers/staging/usbip/vhci_hcd.c
rename to drivers/usb/usbip/vhci_hcd.c
diff --git a/drivers/staging/usbip/vhci_rx.c b/drivers/usb/usbip/vhci_rx.c
similarity index 100%
rename from drivers/staging/usbip/vhci_rx.c
rename to drivers/usb/usbip/vhci_rx.c
diff --git a/drivers/staging/usbip/vhci_sysfs.c b/drivers/usb/usbip/vhci_sysfs.c
similarity index 100%
rename from drivers/staging/usbip/vhci_sysfs.c
rename to drivers/usb/usbip/vhci_sysfs.c
diff --git a/drivers/staging/usbip/vhci_tx.c b/drivers/usb/usbip/vhci_tx.c
similarity index 100%
rename from drivers/staging/usbip/vhci_tx.c
rename to drivers/usb/usbip/vhci_tx.c
diff --git a/drivers/usb/wusbcore/wa-xfer.c b/drivers/usb/wusbcore/wa-xfer.c
index 3e2e4ed..e279015 100644
--- a/drivers/usb/wusbcore/wa-xfer.c
+++ b/drivers/usb/wusbcore/wa-xfer.c
@@ -2602,6 +2602,7 @@
dev = &wa->usb_iface->dev;
--(wa->active_buf_in_urbs);
active_buf_in_urbs = wa->active_buf_in_urbs;
+ rpipe = xfer->ep->hcpriv;
if (usb_pipeisoc(xfer->urb->pipe)) {
struct usb_iso_packet_descriptor *iso_frame_desc =
@@ -2659,7 +2660,6 @@
resubmit_dti = (isoc_data_frame_count ==
urb_frame_count);
} else if (active_buf_in_urbs == 0) {
- rpipe = xfer->ep->hcpriv;
dev_dbg(dev,
"xfer %p 0x%08X#%u: data in done (%zu bytes)\n",
xfer, wa_xfer_id(xfer), seg->index,
@@ -2685,7 +2685,6 @@
*/
resubmit_dti = wa->dti_state != WA_DTI_TRANSFER_RESULT_PENDING;
spin_lock_irqsave(&xfer->lock, flags);
- rpipe = xfer->ep->hcpriv;
if (printk_ratelimit())
dev_err(dev, "xfer %p 0x%08X#%u: data in error %d\n",
xfer, wa_xfer_id(xfer), seg->index,
diff --git a/drivers/video/backlight/pwm_bl.c b/drivers/video/backlight/pwm_bl.c
index d7a3d13..b85983e 100644
--- a/drivers/video/backlight/pwm_bl.c
+++ b/drivers/video/backlight/pwm_bl.c
@@ -173,6 +173,7 @@
data->max_brightness--;
}
+ data->enable_gpio = -EINVAL;
return 0;
}
diff --git a/drivers/video/fbdev/amba-clcd.c b/drivers/video/fbdev/amba-clcd.c
index beadd3e..a7b6217 100644
--- a/drivers/video/fbdev/amba-clcd.c
+++ b/drivers/video/fbdev/amba-clcd.c
@@ -24,6 +24,7 @@
#include <linux/list.h>
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
+#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/hardirq.h>
#include <linux/dma-mapping.h>
@@ -650,6 +651,7 @@
{
struct device_node *endpoint;
int err;
+ unsigned int bpp;
u32 max_bandwidth;
u32 tft_r0b0g0[3];
@@ -667,11 +669,22 @@
err = of_property_read_u32(fb->dev->dev.of_node, "max-memory-bandwidth",
&max_bandwidth);
- if (!err)
- fb->panel->bpp = 8 * max_bandwidth / (fb->panel->mode.xres *
- fb->panel->mode.yres * fb->panel->mode.refresh);
- else
- fb->panel->bpp = 32;
+ if (!err) {
+ /*
+ * max_bandwidth is in bytes per second and pixclock in
+ * pico-seconds, so the maximum allowed bits per pixel is
+ * 8 * max_bandwidth / (PICOS2KHZ(pixclock) * 1000)
+ * Rearrange this calculation to avoid overflow and then ensure
+ * result is a valid format.
+ */
+ bpp = max_bandwidth / (1000 / 8)
+ / PICOS2KHZ(fb->panel->mode.pixclock);
+ bpp = rounddown_pow_of_two(bpp);
+ if (bpp > 32)
+ bpp = 32;
+ } else
+ bpp = 32;
+ fb->panel->bpp = bpp;
#ifdef CONFIG_CPU_BIG_ENDIAN
fb->panel->cntl |= CNTL_BEBO;
diff --git a/drivers/video/fbdev/atmel_lcdfb.c b/drivers/video/fbdev/atmel_lcdfb.c
index 92640d4..1d8bdb9 100644
--- a/drivers/video/fbdev/atmel_lcdfb.c
+++ b/drivers/video/fbdev/atmel_lcdfb.c
@@ -1102,12 +1102,14 @@
timings = of_get_display_timings(display_np);
if (!timings) {
dev_err(dev, "failed to get display timings\n");
+ ret = -EINVAL;
goto put_display_node;
}
timings_np = of_find_node_by_name(display_np, "display-timings");
if (!timings_np) {
dev_err(dev, "failed to find display-timings node\n");
+ ret = -ENODEV;
goto put_display_node;
}
diff --git a/drivers/video/fbdev/chipsfb.c b/drivers/video/fbdev/chipsfb.c
index 206a66b..59abdc6 100644
--- a/drivers/video/fbdev/chipsfb.c
+++ b/drivers/video/fbdev/chipsfb.c
@@ -273,7 +273,7 @@
{ 0xa8, 0x00 }
};
-static void __init chips_hw_init(void)
+static void chips_hw_init(void)
{
int i;
diff --git a/drivers/video/fbdev/da8xx-fb.c b/drivers/video/fbdev/da8xx-fb.c
index 788f6b3..10c876c 100644
--- a/drivers/video/fbdev/da8xx-fb.c
+++ b/drivers/video/fbdev/da8xx-fb.c
@@ -419,7 +419,7 @@
{
u32 reg;
- reg = lcdc_read(LCD_RASTER_TIMING_0_REG) & 0xf;
+ reg = lcdc_read(LCD_RASTER_TIMING_0_REG) & 0x3ff;
reg |= (((back_porch-1) & 0xff) << 24)
| (((front_porch-1) & 0xff) << 16)
| (((pulse_width-1) & 0x3f) << 10);
diff --git a/drivers/video/of_display_timing.c b/drivers/video/of_display_timing.c
index 987edf1..5c098d5 100644
--- a/drivers/video/of_display_timing.c
+++ b/drivers/video/of_display_timing.c
@@ -236,6 +236,7 @@
if (native_mode)
of_node_put(native_mode);
display_timings_release(disp);
+ disp = NULL;
entryfail:
kfree(disp);
dispfail:
diff --git a/fs/btrfs/async-thread.c b/fs/btrfs/async-thread.c
index 5a201d8..fbd76de 100644
--- a/fs/btrfs/async-thread.c
+++ b/fs/btrfs/async-thread.c
@@ -22,7 +22,6 @@
#include <linux/list.h>
#include <linux/spinlock.h>
#include <linux/freezer.h>
-#include <linux/workqueue.h>
#include "async-thread.h"
#include "ctree.h"
@@ -55,8 +54,39 @@
struct __btrfs_workqueue *high;
};
-static inline struct __btrfs_workqueue
-*__btrfs_alloc_workqueue(const char *name, int flags, int max_active,
+static void normal_work_helper(struct btrfs_work *work);
+
+#define BTRFS_WORK_HELPER(name) \
+void btrfs_##name(struct work_struct *arg) \
+{ \
+ struct btrfs_work *work = container_of(arg, struct btrfs_work, \
+ normal_work); \
+ normal_work_helper(work); \
+}
+
+BTRFS_WORK_HELPER(worker_helper);
+BTRFS_WORK_HELPER(delalloc_helper);
+BTRFS_WORK_HELPER(flush_delalloc_helper);
+BTRFS_WORK_HELPER(cache_helper);
+BTRFS_WORK_HELPER(submit_helper);
+BTRFS_WORK_HELPER(fixup_helper);
+BTRFS_WORK_HELPER(endio_helper);
+BTRFS_WORK_HELPER(endio_meta_helper);
+BTRFS_WORK_HELPER(endio_meta_write_helper);
+BTRFS_WORK_HELPER(endio_raid56_helper);
+BTRFS_WORK_HELPER(rmw_helper);
+BTRFS_WORK_HELPER(endio_write_helper);
+BTRFS_WORK_HELPER(freespace_write_helper);
+BTRFS_WORK_HELPER(delayed_meta_helper);
+BTRFS_WORK_HELPER(readahead_helper);
+BTRFS_WORK_HELPER(qgroup_rescan_helper);
+BTRFS_WORK_HELPER(extent_refs_helper);
+BTRFS_WORK_HELPER(scrub_helper);
+BTRFS_WORK_HELPER(scrubwrc_helper);
+BTRFS_WORK_HELPER(scrubnc_helper);
+
+static struct __btrfs_workqueue *
+__btrfs_alloc_workqueue(const char *name, int flags, int max_active,
int thresh)
{
struct __btrfs_workqueue *ret = kzalloc(sizeof(*ret), GFP_NOFS);
@@ -232,13 +262,11 @@
spin_unlock_irqrestore(lock, flags);
}
-static void normal_work_helper(struct work_struct *arg)
+static void normal_work_helper(struct btrfs_work *work)
{
- struct btrfs_work *work;
struct __btrfs_workqueue *wq;
int need_order = 0;
- work = container_of(arg, struct btrfs_work, normal_work);
/*
* We should not touch things inside work in the following cases:
* 1) after work->func() if it has no ordered_free
@@ -262,7 +290,7 @@
trace_btrfs_all_work_done(work);
}
-void btrfs_init_work(struct btrfs_work *work,
+void btrfs_init_work(struct btrfs_work *work, btrfs_work_func_t uniq_func,
btrfs_func_t func,
btrfs_func_t ordered_func,
btrfs_func_t ordered_free)
@@ -270,7 +298,7 @@
work->func = func;
work->ordered_func = ordered_func;
work->ordered_free = ordered_free;
- INIT_WORK(&work->normal_work, normal_work_helper);
+ INIT_WORK(&work->normal_work, uniq_func);
INIT_LIST_HEAD(&work->ordered_list);
work->flags = 0;
}
diff --git a/fs/btrfs/async-thread.h b/fs/btrfs/async-thread.h
index 9c6b66d1..e9e31c9 100644
--- a/fs/btrfs/async-thread.h
+++ b/fs/btrfs/async-thread.h
@@ -19,12 +19,14 @@
#ifndef __BTRFS_ASYNC_THREAD_
#define __BTRFS_ASYNC_THREAD_
+#include <linux/workqueue.h>
struct btrfs_workqueue;
/* Internal use only */
struct __btrfs_workqueue;
struct btrfs_work;
typedef void (*btrfs_func_t)(struct btrfs_work *arg);
+typedef void (*btrfs_work_func_t)(struct work_struct *arg);
struct btrfs_work {
btrfs_func_t func;
@@ -38,11 +40,35 @@
unsigned long flags;
};
+#define BTRFS_WORK_HELPER_PROTO(name) \
+void btrfs_##name(struct work_struct *arg)
+
+BTRFS_WORK_HELPER_PROTO(worker_helper);
+BTRFS_WORK_HELPER_PROTO(delalloc_helper);
+BTRFS_WORK_HELPER_PROTO(flush_delalloc_helper);
+BTRFS_WORK_HELPER_PROTO(cache_helper);
+BTRFS_WORK_HELPER_PROTO(submit_helper);
+BTRFS_WORK_HELPER_PROTO(fixup_helper);
+BTRFS_WORK_HELPER_PROTO(endio_helper);
+BTRFS_WORK_HELPER_PROTO(endio_meta_helper);
+BTRFS_WORK_HELPER_PROTO(endio_meta_write_helper);
+BTRFS_WORK_HELPER_PROTO(endio_raid56_helper);
+BTRFS_WORK_HELPER_PROTO(rmw_helper);
+BTRFS_WORK_HELPER_PROTO(endio_write_helper);
+BTRFS_WORK_HELPER_PROTO(freespace_write_helper);
+BTRFS_WORK_HELPER_PROTO(delayed_meta_helper);
+BTRFS_WORK_HELPER_PROTO(readahead_helper);
+BTRFS_WORK_HELPER_PROTO(qgroup_rescan_helper);
+BTRFS_WORK_HELPER_PROTO(extent_refs_helper);
+BTRFS_WORK_HELPER_PROTO(scrub_helper);
+BTRFS_WORK_HELPER_PROTO(scrubwrc_helper);
+BTRFS_WORK_HELPER_PROTO(scrubnc_helper);
+
struct btrfs_workqueue *btrfs_alloc_workqueue(const char *name,
int flags,
int max_active,
int thresh);
-void btrfs_init_work(struct btrfs_work *work,
+void btrfs_init_work(struct btrfs_work *work, btrfs_work_func_t helper,
btrfs_func_t func,
btrfs_func_t ordered_func,
btrfs_func_t ordered_free);
diff --git a/fs/btrfs/delayed-inode.c b/fs/btrfs/delayed-inode.c
index da775bf..a2e90f8 100644
--- a/fs/btrfs/delayed-inode.c
+++ b/fs/btrfs/delayed-inode.c
@@ -1395,8 +1395,8 @@
return -ENOMEM;
async_work->delayed_root = delayed_root;
- btrfs_init_work(&async_work->work, btrfs_async_run_delayed_root,
- NULL, NULL);
+ btrfs_init_work(&async_work->work, btrfs_delayed_meta_helper,
+ btrfs_async_run_delayed_root, NULL, NULL);
async_work->nr = nr;
btrfs_queue_work(root->fs_info->delayed_workers, &async_work->work);
diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c
index d0ed9e6..a1d36e6 100644
--- a/fs/btrfs/disk-io.c
+++ b/fs/btrfs/disk-io.c
@@ -39,7 +39,6 @@
#include "btrfs_inode.h"
#include "volumes.h"
#include "print-tree.h"
-#include "async-thread.h"
#include "locking.h"
#include "tree-log.h"
#include "free-space-cache.h"
@@ -693,35 +692,41 @@
{
struct end_io_wq *end_io_wq = bio->bi_private;
struct btrfs_fs_info *fs_info;
+ struct btrfs_workqueue *wq;
+ btrfs_work_func_t func;
fs_info = end_io_wq->info;
end_io_wq->error = err;
- btrfs_init_work(&end_io_wq->work, end_workqueue_fn, NULL, NULL);
if (bio->bi_rw & REQ_WRITE) {
- if (end_io_wq->metadata == BTRFS_WQ_ENDIO_METADATA)
- btrfs_queue_work(fs_info->endio_meta_write_workers,
- &end_io_wq->work);
- else if (end_io_wq->metadata == BTRFS_WQ_ENDIO_FREE_SPACE)
- btrfs_queue_work(fs_info->endio_freespace_worker,
- &end_io_wq->work);
- else if (end_io_wq->metadata == BTRFS_WQ_ENDIO_RAID56)
- btrfs_queue_work(fs_info->endio_raid56_workers,
- &end_io_wq->work);
- else
- btrfs_queue_work(fs_info->endio_write_workers,
- &end_io_wq->work);
+ if (end_io_wq->metadata == BTRFS_WQ_ENDIO_METADATA) {
+ wq = fs_info->endio_meta_write_workers;
+ func = btrfs_endio_meta_write_helper;
+ } else if (end_io_wq->metadata == BTRFS_WQ_ENDIO_FREE_SPACE) {
+ wq = fs_info->endio_freespace_worker;
+ func = btrfs_freespace_write_helper;
+ } else if (end_io_wq->metadata == BTRFS_WQ_ENDIO_RAID56) {
+ wq = fs_info->endio_raid56_workers;
+ func = btrfs_endio_raid56_helper;
+ } else {
+ wq = fs_info->endio_write_workers;
+ func = btrfs_endio_write_helper;
+ }
} else {
- if (end_io_wq->metadata == BTRFS_WQ_ENDIO_RAID56)
- btrfs_queue_work(fs_info->endio_raid56_workers,
- &end_io_wq->work);
- else if (end_io_wq->metadata)
- btrfs_queue_work(fs_info->endio_meta_workers,
- &end_io_wq->work);
- else
- btrfs_queue_work(fs_info->endio_workers,
- &end_io_wq->work);
+ if (end_io_wq->metadata == BTRFS_WQ_ENDIO_RAID56) {
+ wq = fs_info->endio_raid56_workers;
+ func = btrfs_endio_raid56_helper;
+ } else if (end_io_wq->metadata) {
+ wq = fs_info->endio_meta_workers;
+ func = btrfs_endio_meta_helper;
+ } else {
+ wq = fs_info->endio_workers;
+ func = btrfs_endio_helper;
+ }
}
+
+ btrfs_init_work(&end_io_wq->work, func, end_workqueue_fn, NULL, NULL);
+ btrfs_queue_work(wq, &end_io_wq->work);
}
/*
@@ -828,7 +833,7 @@
async->submit_bio_start = submit_bio_start;
async->submit_bio_done = submit_bio_done;
- btrfs_init_work(&async->work, run_one_async_start,
+ btrfs_init_work(&async->work, btrfs_worker_helper, run_one_async_start,
run_one_async_done, run_one_async_free);
async->bio_flags = bio_flags;
@@ -3450,7 +3455,8 @@
btrfs_set_stack_device_generation(dev_item, 0);
btrfs_set_stack_device_type(dev_item, dev->type);
btrfs_set_stack_device_id(dev_item, dev->devid);
- btrfs_set_stack_device_total_bytes(dev_item, dev->total_bytes);
+ btrfs_set_stack_device_total_bytes(dev_item,
+ dev->disk_total_bytes);
btrfs_set_stack_device_bytes_used(dev_item, dev->bytes_used);
btrfs_set_stack_device_io_align(dev_item, dev->io_align);
btrfs_set_stack_device_io_width(dev_item, dev->io_width);
diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index 102ed31..3efe1c3 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -552,7 +552,8 @@
caching_ctl->block_group = cache;
caching_ctl->progress = cache->key.objectid;
atomic_set(&caching_ctl->count, 1);
- btrfs_init_work(&caching_ctl->work, caching_thread, NULL, NULL);
+ btrfs_init_work(&caching_ctl->work, btrfs_cache_helper,
+ caching_thread, NULL, NULL);
spin_lock(&cache->lock);
/*
@@ -2749,8 +2750,8 @@
async->sync = 0;
init_completion(&async->wait);
- btrfs_init_work(&async->work, delayed_ref_async_start,
- NULL, NULL);
+ btrfs_init_work(&async->work, btrfs_extent_refs_helper,
+ delayed_ref_async_start, NULL, NULL);
btrfs_queue_work(root->fs_info->extent_workers, &async->work);
@@ -3586,13 +3587,7 @@
*/
static u64 btrfs_reduce_alloc_profile(struct btrfs_root *root, u64 flags)
{
- /*
- * we add in the count of missing devices because we want
- * to make sure that any RAID levels on a degraded FS
- * continue to be honored.
- */
- u64 num_devices = root->fs_info->fs_devices->rw_devices +
- root->fs_info->fs_devices->missing_devices;
+ u64 num_devices = root->fs_info->fs_devices->rw_devices;
u64 target;
u64 tmp;
@@ -8440,13 +8435,7 @@
if (stripped)
return extended_to_chunk(stripped);
- /*
- * we add in the count of missing devices because we want
- * to make sure that any RAID levels on a degraded FS
- * continue to be honored.
- */
- num_devices = root->fs_info->fs_devices->rw_devices +
- root->fs_info->fs_devices->missing_devices;
+ num_devices = root->fs_info->fs_devices->rw_devices;
stripped = BTRFS_BLOCK_GROUP_RAID0 |
BTRFS_BLOCK_GROUP_RAID5 | BTRFS_BLOCK_GROUP_RAID6 |
diff --git a/fs/btrfs/extent_io.c b/fs/btrfs/extent_io.c
index 3e11aab..af0359d 100644
--- a/fs/btrfs/extent_io.c
+++ b/fs/btrfs/extent_io.c
@@ -2532,6 +2532,7 @@
test_bit(BIO_UPTODATE, &bio->bi_flags);
if (err)
uptodate = 0;
+ offset += len;
continue;
}
}
@@ -4207,8 +4208,8 @@
return -ENOMEM;
path->leave_spinning = 1;
- start = ALIGN(start, BTRFS_I(inode)->root->sectorsize);
- len = ALIGN(len, BTRFS_I(inode)->root->sectorsize);
+ start = round_down(start, BTRFS_I(inode)->root->sectorsize);
+ len = round_up(max, BTRFS_I(inode)->root->sectorsize) - start;
/*
* lookup the last file extent. We're not using i_size here
diff --git a/fs/btrfs/file.c b/fs/btrfs/file.c
index d3afac2..36861b7 100644
--- a/fs/btrfs/file.c
+++ b/fs/btrfs/file.c
@@ -1840,7 +1840,15 @@
{
if (filp->private_data)
btrfs_ioctl_trans_end(filp);
- filemap_flush(inode->i_mapping);
+ /*
+ * ordered_data_close is set by settattr when we are about to truncate
+ * a file from a non-zero size to a zero size. This tries to
+ * flush down new bytes that may have been written if the
+ * application were using truncate to replace a file in place.
+ */
+ if (test_and_clear_bit(BTRFS_INODE_ORDERED_DATA_CLOSE,
+ &BTRFS_I(inode)->runtime_flags))
+ filemap_flush(inode->i_mapping);
return 0;
}
@@ -2088,10 +2096,9 @@
goto out;
}
- if (hole_mergeable(inode, leaf, path->slots[0]+1, offset, end)) {
+ if (hole_mergeable(inode, leaf, path->slots[0], offset, end)) {
u64 num_bytes;
- path->slots[0]++;
key.offset = offset;
btrfs_set_item_key_safe(root, path, &key);
fi = btrfs_item_ptr(leaf, path->slots[0],
@@ -2216,7 +2223,7 @@
goto out_only_mutex;
}
- lockstart = round_up(offset , BTRFS_I(inode)->root->sectorsize);
+ lockstart = round_up(offset, BTRFS_I(inode)->root->sectorsize);
lockend = round_down(offset + len,
BTRFS_I(inode)->root->sectorsize) - 1;
same_page = ((offset >> PAGE_CACHE_SHIFT) ==
@@ -2277,7 +2284,7 @@
tail_start + tail_len, 0, 1);
if (ret)
goto out_only_mutex;
- }
+ }
}
}
diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c
index 03708ef..9c194bd 100644
--- a/fs/btrfs/inode.c
+++ b/fs/btrfs/inode.c
@@ -1096,8 +1096,10 @@
async_cow->end = cur_end;
INIT_LIST_HEAD(&async_cow->extents);
- btrfs_init_work(&async_cow->work, async_cow_start,
- async_cow_submit, async_cow_free);
+ btrfs_init_work(&async_cow->work,
+ btrfs_delalloc_helper,
+ async_cow_start, async_cow_submit,
+ async_cow_free);
nr_pages = (cur_end - start + PAGE_CACHE_SIZE) >>
PAGE_CACHE_SHIFT;
@@ -1881,7 +1883,8 @@
SetPageChecked(page);
page_cache_get(page);
- btrfs_init_work(&fixup->work, btrfs_writepage_fixup_worker, NULL, NULL);
+ btrfs_init_work(&fixup->work, btrfs_fixup_helper,
+ btrfs_writepage_fixup_worker, NULL, NULL);
fixup->page = page;
btrfs_queue_work(root->fs_info->fixup_workers, &fixup->work);
return -EBUSY;
@@ -2822,7 +2825,8 @@
struct inode *inode = page->mapping->host;
struct btrfs_root *root = BTRFS_I(inode)->root;
struct btrfs_ordered_extent *ordered_extent = NULL;
- struct btrfs_workqueue *workers;
+ struct btrfs_workqueue *wq;
+ btrfs_work_func_t func;
trace_btrfs_writepage_end_io_hook(page, start, end, uptodate);
@@ -2831,13 +2835,17 @@
end - start + 1, uptodate))
return 0;
- btrfs_init_work(&ordered_extent->work, finish_ordered_fn, NULL, NULL);
+ if (btrfs_is_free_space_inode(inode)) {
+ wq = root->fs_info->endio_freespace_worker;
+ func = btrfs_freespace_write_helper;
+ } else {
+ wq = root->fs_info->endio_write_workers;
+ func = btrfs_endio_write_helper;
+ }
- if (btrfs_is_free_space_inode(inode))
- workers = root->fs_info->endio_freespace_worker;
- else
- workers = root->fs_info->endio_write_workers;
- btrfs_queue_work(workers, &ordered_extent->work);
+ btrfs_init_work(&ordered_extent->work, func, finish_ordered_fn, NULL,
+ NULL);
+ btrfs_queue_work(wq, &ordered_extent->work);
return 0;
}
@@ -4674,6 +4682,11 @@
clear_bit(EXTENT_FLAG_LOGGING, &em->flags);
remove_extent_mapping(map_tree, em);
free_extent_map(em);
+ if (need_resched()) {
+ write_unlock(&map_tree->lock);
+ cond_resched();
+ write_lock(&map_tree->lock);
+ }
}
write_unlock(&map_tree->lock);
@@ -4696,6 +4709,7 @@
&cached_state, GFP_NOFS);
free_extent_state(state);
+ cond_resched();
spin_lock(&io_tree->lock);
}
spin_unlock(&io_tree->lock);
@@ -5181,6 +5195,42 @@
iput(inode);
inode = ERR_PTR(ret);
}
+ /*
+ * If orphan cleanup did remove any orphans, it means the tree
+ * was modified and therefore the commit root is not the same as
+ * the current root anymore. This is a problem, because send
+ * uses the commit root and therefore can see inode items that
+ * don't exist in the current root anymore, and for example make
+ * calls to btrfs_iget, which will do tree lookups based on the
+ * current root and not on the commit root. Those lookups will
+ * fail, returning a -ESTALE error, and making send fail with
+ * that error. So make sure a send does not see any orphans we
+ * have just removed, and that it will see the same inodes
+ * regardless of whether a transaction commit happened before
+ * it started (meaning that the commit root will be the same as
+ * the current root) or not.
+ */
+ if (sub_root->node != sub_root->commit_root) {
+ u64 sub_flags = btrfs_root_flags(&sub_root->root_item);
+
+ if (sub_flags & BTRFS_ROOT_SUBVOL_RDONLY) {
+ struct extent_buffer *eb;
+
+ /*
+ * Assert we can't have races between dentry
+ * lookup called through the snapshot creation
+ * ioctl and the VFS.
+ */
+ ASSERT(mutex_is_locked(&dir->i_mutex));
+
+ down_write(&root->fs_info->commit_root_sem);
+ eb = sub_root->commit_root;
+ sub_root->commit_root =
+ btrfs_root_node(sub_root);
+ up_write(&root->fs_info->commit_root_sem);
+ free_extent_buffer(eb);
+ }
+ }
}
return inode;
@@ -5606,6 +5656,13 @@
}
/*
+ * O_TMPFILE, set link count to 0, so that after this point,
+ * we fill in an inode item with the correct link count.
+ */
+ if (!name)
+ set_nlink(inode, 0);
+
+ /*
* we have to initialize this early, so we can reclaim the inode
* number if we fail afterwards in this function.
*/
@@ -6097,14 +6154,14 @@
static int merge_extent_mapping(struct extent_map_tree *em_tree,
struct extent_map *existing,
struct extent_map *em,
- u64 map_start, u64 map_len)
+ u64 map_start)
{
u64 start_diff;
BUG_ON(map_start < em->start || map_start >= extent_map_end(em));
start_diff = map_start - em->start;
em->start = map_start;
- em->len = map_len;
+ em->len = existing->start - em->start;
if (em->block_start < EXTENT_MAP_LAST_BYTE &&
!test_bit(EXTENT_FLAG_COMPRESSED, &em->flags)) {
em->block_start += start_diff;
@@ -6275,6 +6332,8 @@
goto not_found;
if (start + len <= found_key.offset)
goto not_found;
+ if (start > found_key.offset)
+ goto next;
em->start = start;
em->orig_start = start;
em->len = found_key.offset - start;
@@ -6390,8 +6449,7 @@
em->len);
if (existing) {
err = merge_extent_mapping(em_tree, existing,
- em, start,
- root->sectorsize);
+ em, start);
free_extent_map(existing);
if (err) {
free_extent_map(em);
@@ -7158,7 +7216,8 @@
if (!ret)
goto out_test;
- btrfs_init_work(&ordered->work, finish_ordered_fn, NULL, NULL);
+ btrfs_init_work(&ordered->work, btrfs_endio_write_helper,
+ finish_ordered_fn, NULL, NULL);
btrfs_queue_work(root->fs_info->endio_write_workers,
&ordered->work);
out_test:
@@ -7306,10 +7365,8 @@
map_length = orig_bio->bi_iter.bi_size;
ret = btrfs_map_block(root->fs_info, rw, start_sector << 9,
&map_length, NULL, 0);
- if (ret) {
- bio_put(orig_bio);
+ if (ret)
return -EIO;
- }
if (map_length >= orig_bio->bi_iter.bi_size) {
bio = orig_bio;
@@ -7326,6 +7383,7 @@
bio = btrfs_dio_bio_alloc(orig_bio->bi_bdev, start_sector, GFP_NOFS);
if (!bio)
return -ENOMEM;
+
bio->bi_private = dip;
bio->bi_end_io = btrfs_end_dio_bio;
atomic_inc(&dip->pending_bios);
@@ -7534,7 +7592,8 @@
count = iov_iter_count(iter);
if (test_bit(BTRFS_INODE_HAS_ASYNC_EXTENT,
&BTRFS_I(inode)->runtime_flags))
- filemap_fdatawrite_range(inode->i_mapping, offset, count);
+ filemap_fdatawrite_range(inode->i_mapping, offset,
+ offset + count - 1);
if (rw & WRITE) {
/*
@@ -8495,7 +8554,9 @@
work->inode = inode;
work->wait = wait;
work->delay_iput = delay_iput;
- btrfs_init_work(&work->work, btrfs_run_delalloc_work, NULL, NULL);
+ WARN_ON_ONCE(!inode);
+ btrfs_init_work(&work->work, btrfs_flush_delalloc_helper,
+ btrfs_run_delalloc_work, NULL, NULL);
return work;
}
@@ -8979,6 +9040,14 @@
if (ret)
goto out;
+ /*
+ * We set number of links to 0 in btrfs_new_inode(), and here we set
+ * it to 1 because d_tmpfile() will issue a warning if the count is 0,
+ * through:
+ *
+ * d_tmpfile() -> inode_dec_link_count() -> drop_nlink()
+ */
+ set_nlink(inode, 1);
d_tmpfile(dentry, inode);
mark_inode_dirty(inode);
diff --git a/fs/btrfs/ioctl.c b/fs/btrfs/ioctl.c
index 47aceb4..fce6fd0e 100644
--- a/fs/btrfs/ioctl.c
+++ b/fs/btrfs/ioctl.c
@@ -711,39 +711,6 @@
if (ret)
goto fail;
- ret = btrfs_orphan_cleanup(pending_snapshot->snap);
- if (ret)
- goto fail;
-
- /*
- * If orphan cleanup did remove any orphans, it means the tree was
- * modified and therefore the commit root is not the same as the
- * current root anymore. This is a problem, because send uses the
- * commit root and therefore can see inode items that don't exist
- * in the current root anymore, and for example make calls to
- * btrfs_iget, which will do tree lookups based on the current root
- * and not on the commit root. Those lookups will fail, returning a
- * -ESTALE error, and making send fail with that error. So make sure
- * a send does not see any orphans we have just removed, and that it
- * will see the same inodes regardless of whether a transaction
- * commit happened before it started (meaning that the commit root
- * will be the same as the current root) or not.
- */
- if (readonly && pending_snapshot->snap->node !=
- pending_snapshot->snap->commit_root) {
- trans = btrfs_join_transaction(pending_snapshot->snap);
- if (IS_ERR(trans) && PTR_ERR(trans) != -ENOENT) {
- ret = PTR_ERR(trans);
- goto fail;
- }
- if (!IS_ERR(trans)) {
- ret = btrfs_commit_transaction(trans,
- pending_snapshot->snap);
- if (ret)
- goto fail;
- }
- }
-
inode = btrfs_lookup_dentry(dentry->d_parent->d_inode, dentry);
if (IS_ERR(inode)) {
ret = PTR_ERR(inode);
@@ -3527,7 +3494,8 @@
btrfs_mark_buffer_dirty(leaf);
btrfs_release_path(path);
- last_dest_end = new_key.offset + datal;
+ last_dest_end = ALIGN(new_key.offset + datal,
+ root->sectorsize);
ret = clone_finish_inode_update(trans, inode,
last_dest_end,
destoff, olen);
diff --git a/fs/btrfs/ordered-data.c b/fs/btrfs/ordered-data.c
index 963895c..ac734ec 100644
--- a/fs/btrfs/ordered-data.c
+++ b/fs/btrfs/ordered-data.c
@@ -615,6 +615,7 @@
spin_unlock(&root->ordered_extent_lock);
btrfs_init_work(&ordered->flush_work,
+ btrfs_flush_delalloc_helper,
btrfs_run_ordered_extent_work, NULL, NULL);
list_add_tail(&ordered->work_list, &works);
btrfs_queue_work(root->fs_info->flush_workers,
diff --git a/fs/btrfs/qgroup.c b/fs/btrfs/qgroup.c
index b497498..ded5c60 100644
--- a/fs/btrfs/qgroup.c
+++ b/fs/btrfs/qgroup.c
@@ -1973,7 +1973,7 @@
elem.seq, &roots);
btrfs_put_tree_mod_seq(fs_info, &elem);
if (ret < 0)
- return ret;
+ goto out;
if (roots->nnodes != 1)
goto out;
@@ -2720,6 +2720,7 @@
memset(&fs_info->qgroup_rescan_work, 0,
sizeof(fs_info->qgroup_rescan_work));
btrfs_init_work(&fs_info->qgroup_rescan_work,
+ btrfs_qgroup_rescan_helper,
btrfs_qgroup_rescan_worker, NULL, NULL);
if (ret) {
diff --git a/fs/btrfs/raid56.c b/fs/btrfs/raid56.c
index 4a88f07..0a6b6e4 100644
--- a/fs/btrfs/raid56.c
+++ b/fs/btrfs/raid56.c
@@ -1416,7 +1416,8 @@
static void async_rmw_stripe(struct btrfs_raid_bio *rbio)
{
- btrfs_init_work(&rbio->work, rmw_work, NULL, NULL);
+ btrfs_init_work(&rbio->work, btrfs_rmw_helper,
+ rmw_work, NULL, NULL);
btrfs_queue_work(rbio->fs_info->rmw_workers,
&rbio->work);
@@ -1424,7 +1425,8 @@
static void async_read_rebuild(struct btrfs_raid_bio *rbio)
{
- btrfs_init_work(&rbio->work, read_rebuild_work, NULL, NULL);
+ btrfs_init_work(&rbio->work, btrfs_rmw_helper,
+ read_rebuild_work, NULL, NULL);
btrfs_queue_work(rbio->fs_info->rmw_workers,
&rbio->work);
@@ -1665,7 +1667,8 @@
plug = container_of(cb, struct btrfs_plug_cb, cb);
if (from_schedule) {
- btrfs_init_work(&plug->work, unplug_work, NULL, NULL);
+ btrfs_init_work(&plug->work, btrfs_rmw_helper,
+ unplug_work, NULL, NULL);
btrfs_queue_work(plug->info->rmw_workers,
&plug->work);
return;
diff --git a/fs/btrfs/reada.c b/fs/btrfs/reada.c
index 09230cf..20408c6 100644
--- a/fs/btrfs/reada.c
+++ b/fs/btrfs/reada.c
@@ -798,7 +798,8 @@
/* FIXME we cannot handle this properly right now */
BUG();
}
- btrfs_init_work(&rmw->work, reada_start_machine_worker, NULL, NULL);
+ btrfs_init_work(&rmw->work, btrfs_readahead_helper,
+ reada_start_machine_worker, NULL, NULL);
rmw->fs_info = fs_info;
btrfs_queue_work(fs_info->readahead_workers, &rmw->work);
diff --git a/fs/btrfs/scrub.c b/fs/btrfs/scrub.c
index b6d198f..f4a41f3 100644
--- a/fs/btrfs/scrub.c
+++ b/fs/btrfs/scrub.c
@@ -428,8 +428,8 @@
sbio->index = i;
sbio->sctx = sctx;
sbio->page_count = 0;
- btrfs_init_work(&sbio->work, scrub_bio_end_io_worker,
- NULL, NULL);
+ btrfs_init_work(&sbio->work, btrfs_scrub_helper,
+ scrub_bio_end_io_worker, NULL, NULL);
if (i != SCRUB_BIOS_PER_SCTX - 1)
sctx->bios[i]->next_free = i + 1;
@@ -999,8 +999,8 @@
fixup_nodatasum->root = fs_info->extent_root;
fixup_nodatasum->mirror_num = failed_mirror_index + 1;
scrub_pending_trans_workers_inc(sctx);
- btrfs_init_work(&fixup_nodatasum->work, scrub_fixup_nodatasum,
- NULL, NULL);
+ btrfs_init_work(&fixup_nodatasum->work, btrfs_scrub_helper,
+ scrub_fixup_nodatasum, NULL, NULL);
btrfs_queue_work(fs_info->scrub_workers,
&fixup_nodatasum->work);
goto out;
@@ -1616,7 +1616,8 @@
sbio->err = err;
sbio->bio = bio;
- btrfs_init_work(&sbio->work, scrub_wr_bio_end_io_worker, NULL, NULL);
+ btrfs_init_work(&sbio->work, btrfs_scrubwrc_helper,
+ scrub_wr_bio_end_io_worker, NULL, NULL);
btrfs_queue_work(fs_info->scrub_wr_completion_workers, &sbio->work);
}
@@ -2904,6 +2905,7 @@
struct scrub_ctx *sctx;
int ret;
struct btrfs_device *dev;
+ struct rcu_string *name;
if (btrfs_fs_closing(fs_info))
return -EINVAL;
@@ -2965,6 +2967,16 @@
return -ENODEV;
}
+ if (!is_dev_replace && !readonly && !dev->writeable) {
+ mutex_unlock(&fs_info->fs_devices->device_list_mutex);
+ rcu_read_lock();
+ name = rcu_dereference(dev->name);
+ btrfs_err(fs_info, "scrub: device %s is not writable",
+ name->str);
+ rcu_read_unlock();
+ return -EROFS;
+ }
+
mutex_lock(&fs_info->scrub_lock);
if (!dev->in_fs_metadata || dev->is_tgtdev_for_dev_replace) {
mutex_unlock(&fs_info->scrub_lock);
@@ -3203,7 +3215,8 @@
nocow_ctx->len = len;
nocow_ctx->mirror_num = mirror_num;
nocow_ctx->physical_for_dev_replace = physical_for_dev_replace;
- btrfs_init_work(&nocow_ctx->work, copy_nocow_pages_worker, NULL, NULL);
+ btrfs_init_work(&nocow_ctx->work, btrfs_scrubnc_helper,
+ copy_nocow_pages_worker, NULL, NULL);
INIT_LIST_HEAD(&nocow_ctx->inodes);
btrfs_queue_work(fs_info->scrub_nocow_workers,
&nocow_ctx->work);
diff --git a/fs/btrfs/sysfs.c b/fs/btrfs/sysfs.c
index 7869936..12e5355 100644
--- a/fs/btrfs/sysfs.c
+++ b/fs/btrfs/sysfs.c
@@ -614,7 +614,7 @@
if (!fs_info->device_dir_kobj)
return -EINVAL;
- if (one_device) {
+ if (one_device && one_device->bdev) {
disk = one_device->bdev->bd_part;
disk_kobj = &part_to_dev(disk)->kobj;
diff --git a/fs/btrfs/tree-log.c b/fs/btrfs/tree-log.c
index 9e1f2cd..7e0e6e3 100644
--- a/fs/btrfs/tree-log.c
+++ b/fs/btrfs/tree-log.c
@@ -3298,7 +3298,7 @@
struct list_head ordered_sums;
int skip_csum = BTRFS_I(inode)->flags & BTRFS_INODE_NODATASUM;
bool has_extents = false;
- bool need_find_last_extent = (*last_extent == 0);
+ bool need_find_last_extent = true;
bool done = false;
INIT_LIST_HEAD(&ordered_sums);
@@ -3352,8 +3352,7 @@
*/
if (ins_keys[i].type == BTRFS_EXTENT_DATA_KEY) {
has_extents = true;
- if (need_find_last_extent &&
- first_key.objectid == (u64)-1)
+ if (first_key.objectid == (u64)-1)
first_key = ins_keys[i];
} else {
need_find_last_extent = false;
@@ -3427,6 +3426,16 @@
if (!has_extents)
return ret;
+ if (need_find_last_extent && *last_extent == first_key.offset) {
+ /*
+ * We don't have any leafs between our current one and the one
+ * we processed before that can have file extent items for our
+ * inode (and have a generation number smaller than our current
+ * transaction id).
+ */
+ need_find_last_extent = false;
+ }
+
/*
* Because we use btrfs_search_forward we could skip leaves that were
* not modified and then assume *last_extent is valid when it really
@@ -3537,7 +3546,7 @@
0, 0);
if (ret)
break;
- *last_extent = offset + len;
+ *last_extent = extent_end;
}
/*
* Need to let the callers know we dropped the path so they should
diff --git a/fs/btrfs/volumes.c b/fs/btrfs/volumes.c
index 6cb82f6..340a92d 100644
--- a/fs/btrfs/volumes.c
+++ b/fs/btrfs/volumes.c
@@ -508,6 +508,44 @@
ret = 1;
device->fs_devices = fs_devices;
} else if (!device->name || strcmp(device->name->str, path)) {
+ /*
+ * When FS is already mounted.
+ * 1. If you are here and if the device->name is NULL that
+ * means this device was missing at time of FS mount.
+ * 2. If you are here and if the device->name is different
+ * from 'path' that means either
+ * a. The same device disappeared and reappeared with
+ * different name. or
+ * b. The missing-disk-which-was-replaced, has
+ * reappeared now.
+ *
+ * We must allow 1 and 2a above. But 2b would be a spurious
+ * and unintentional.
+ *
+ * Further in case of 1 and 2a above, the disk at 'path'
+ * would have missed some transaction when it was away and
+ * in case of 2a the stale bdev has to be updated as well.
+ * 2b must not be allowed at all time.
+ */
+
+ /*
+ * As of now don't allow update to btrfs_fs_device through
+ * the btrfs dev scan cli, after FS has been mounted.
+ */
+ if (fs_devices->opened) {
+ return -EBUSY;
+ } else {
+ /*
+ * That is if the FS is _not_ mounted and if you
+ * are here, that means there is more than one
+ * disk with same uuid and devid.We keep the one
+ * with larger generation number or the last-in if
+ * generation are equal.
+ */
+ if (found_transid < device->generation)
+ return -EEXIST;
+ }
+
name = rcu_string_strdup(path, GFP_NOFS);
if (!name)
return -ENOMEM;
@@ -519,6 +557,15 @@
}
}
+ /*
+ * Unmount does not free the btrfs_device struct but would zero
+ * generation along with most of the other members. So just update
+ * it back. We need it to pick the disk with largest generation
+ * (as above).
+ */
+ if (!fs_devices->opened)
+ device->generation = found_transid;
+
if (found_transid > fs_devices->latest_trans) {
fs_devices->latest_devid = devid;
fs_devices->latest_trans = found_transid;
@@ -1436,7 +1483,7 @@
btrfs_set_device_io_align(leaf, dev_item, device->io_align);
btrfs_set_device_io_width(leaf, dev_item, device->io_width);
btrfs_set_device_sector_size(leaf, dev_item, device->sector_size);
- btrfs_set_device_total_bytes(leaf, dev_item, device->total_bytes);
+ btrfs_set_device_total_bytes(leaf, dev_item, device->disk_total_bytes);
btrfs_set_device_bytes_used(leaf, dev_item, device->bytes_used);
btrfs_set_device_group(leaf, dev_item, 0);
btrfs_set_device_seek_speed(leaf, dev_item, 0);
@@ -1671,7 +1718,7 @@
device->fs_devices->total_devices--;
if (device->missing)
- root->fs_info->fs_devices->missing_devices--;
+ device->fs_devices->missing_devices--;
next_device = list_entry(root->fs_info->fs_devices->devices.next,
struct btrfs_device, dev_list);
@@ -1801,8 +1848,12 @@
if (srcdev->bdev) {
fs_info->fs_devices->open_devices--;
- /* zero out the old super */
- btrfs_scratch_superblock(srcdev);
+ /*
+ * zero out the old super if it is not writable
+ * (e.g. seed device)
+ */
+ if (srcdev->writeable)
+ btrfs_scratch_superblock(srcdev);
}
call_rcu(&srcdev->rcu, free_device);
@@ -1941,6 +1992,9 @@
fs_devices->seeding = 0;
fs_devices->num_devices = 0;
fs_devices->open_devices = 0;
+ fs_devices->missing_devices = 0;
+ fs_devices->num_can_discard = 0;
+ fs_devices->rotating = 0;
fs_devices->seed = seed_devices;
generate_random_uuid(fs_devices->fsid);
@@ -5800,7 +5854,8 @@
else
generate_random_uuid(dev->uuid);
- btrfs_init_work(&dev->work, pending_bios_fn, NULL, NULL);
+ btrfs_init_work(&dev->work, btrfs_submit_helper,
+ pending_bios_fn, NULL, NULL);
return dev;
}
diff --git a/fs/ext4/ext4.h b/fs/ext4/ext4.h
index 5b19760..b0c225c 100644
--- a/fs/ext4/ext4.h
+++ b/fs/ext4/ext4.h
@@ -1825,7 +1825,7 @@
/*
* Special error return code only used by dx_probe() and its callers.
*/
-#define ERR_BAD_DX_DIR -75000
+#define ERR_BAD_DX_DIR (-(MAX_ERRNO - 1))
/*
* Timeout and state flag for lazy initialization inode thread.
@@ -2454,6 +2454,22 @@
up_write(&EXT4_I(inode)->i_data_sem);
}
+/* Update i_size, i_disksize. Requires i_mutex to avoid races with truncate */
+static inline int ext4_update_inode_size(struct inode *inode, loff_t newsize)
+{
+ int changed = 0;
+
+ if (newsize > inode->i_size) {
+ i_size_write(inode, newsize);
+ changed = 1;
+ }
+ if (newsize > EXT4_I(inode)->i_disksize) {
+ ext4_update_i_disksize(inode, newsize);
+ changed |= 2;
+ }
+ return changed;
+}
+
struct ext4_group_info {
unsigned long bb_state;
struct rb_root bb_free_root;
diff --git a/fs/ext4/extents.c b/fs/ext4/extents.c
index 76c2df3..74292a7 100644
--- a/fs/ext4/extents.c
+++ b/fs/ext4/extents.c
@@ -4665,7 +4665,8 @@
}
static int ext4_alloc_file_blocks(struct file *file, ext4_lblk_t offset,
- ext4_lblk_t len, int flags, int mode)
+ ext4_lblk_t len, loff_t new_size,
+ int flags, int mode)
{
struct inode *inode = file_inode(file);
handle_t *handle;
@@ -4674,8 +4675,10 @@
int retries = 0;
struct ext4_map_blocks map;
unsigned int credits;
+ loff_t epos;
map.m_lblk = offset;
+ map.m_len = len;
/*
* Don't normalize the request if it can fit in one extent so
* that it doesn't get unnecessarily split into multiple
@@ -4690,9 +4693,7 @@
credits = ext4_chunk_trans_blocks(inode, len);
retry:
- while (ret >= 0 && ret < len) {
- map.m_lblk = map.m_lblk + ret;
- map.m_len = len = len - ret;
+ while (ret >= 0 && len) {
handle = ext4_journal_start(inode, EXT4_HT_MAP_BLOCKS,
credits);
if (IS_ERR(handle)) {
@@ -4709,6 +4710,21 @@
ret2 = ext4_journal_stop(handle);
break;
}
+ map.m_lblk += ret;
+ map.m_len = len = len - ret;
+ epos = (loff_t)map.m_lblk << inode->i_blkbits;
+ inode->i_ctime = ext4_current_time(inode);
+ if (new_size) {
+ if (epos > new_size)
+ epos = new_size;
+ if (ext4_update_inode_size(inode, epos) & 0x1)
+ inode->i_mtime = inode->i_ctime;
+ } else {
+ if (epos > inode->i_size)
+ ext4_set_inode_flag(inode,
+ EXT4_INODE_EOFBLOCKS);
+ }
+ ext4_mark_inode_dirty(handle, inode);
ret2 = ext4_journal_stop(handle);
if (ret2)
break;
@@ -4731,7 +4747,8 @@
loff_t new_size = 0;
int ret = 0;
int flags;
- int partial;
+ int credits;
+ int partial_begin, partial_end;
loff_t start, end;
ext4_lblk_t lblk;
struct address_space *mapping = inode->i_mapping;
@@ -4771,7 +4788,8 @@
if (start < offset || end > offset + len)
return -EINVAL;
- partial = (offset + len) & ((1 << blkbits) - 1);
+ partial_begin = offset & ((1 << blkbits) - 1);
+ partial_end = (offset + len) & ((1 << blkbits) - 1);
lblk = start >> blkbits;
max_blocks = (end >> blkbits);
@@ -4805,7 +4823,7 @@
* If we have a partial block after EOF we have to allocate
* the entire block.
*/
- if (partial)
+ if (partial_end)
max_blocks += 1;
}
@@ -4813,6 +4831,7 @@
/* Now release the pages and zero block aligned part of pages*/
truncate_pagecache_range(inode, start, end - 1);
+ inode->i_mtime = inode->i_ctime = ext4_current_time(inode);
/* Wait all existing dio workers, newcomers will block on i_mutex */
ext4_inode_block_unlocked_dio(inode);
@@ -4825,13 +4844,22 @@
if (ret)
goto out_dio;
- ret = ext4_alloc_file_blocks(file, lblk, max_blocks, flags,
- mode);
+ ret = ext4_alloc_file_blocks(file, lblk, max_blocks, new_size,
+ flags, mode);
if (ret)
goto out_dio;
}
+ if (!partial_begin && !partial_end)
+ goto out_dio;
- handle = ext4_journal_start(inode, EXT4_HT_MISC, 4);
+ /*
+ * In worst case we have to writeout two nonadjacent unwritten
+ * blocks and update the inode
+ */
+ credits = (2 * ext4_ext_index_trans_blocks(inode, 2)) + 1;
+ if (ext4_should_journal_data(inode))
+ credits += 2;
+ handle = ext4_journal_start(inode, EXT4_HT_MISC, credits);
if (IS_ERR(handle)) {
ret = PTR_ERR(handle);
ext4_std_error(inode->i_sb, ret);
@@ -4839,12 +4867,8 @@
}
inode->i_mtime = inode->i_ctime = ext4_current_time(inode);
-
if (new_size) {
- if (new_size > i_size_read(inode))
- i_size_write(inode, new_size);
- if (new_size > EXT4_I(inode)->i_disksize)
- ext4_update_i_disksize(inode, new_size);
+ ext4_update_inode_size(inode, new_size);
} else {
/*
* Mark that we allocate beyond EOF so the subsequent truncate
@@ -4853,7 +4877,6 @@
if ((offset + len) > i_size_read(inode))
ext4_set_inode_flag(inode, EXT4_INODE_EOFBLOCKS);
}
-
ext4_mark_inode_dirty(handle, inode);
/* Zero out partial block at the edges of the range */
@@ -4880,13 +4903,11 @@
long ext4_fallocate(struct file *file, int mode, loff_t offset, loff_t len)
{
struct inode *inode = file_inode(file);
- handle_t *handle;
loff_t new_size = 0;
unsigned int max_blocks;
int ret = 0;
int flags;
ext4_lblk_t lblk;
- struct timespec tv;
unsigned int blkbits = inode->i_blkbits;
/* Return error if mode is not supported */
@@ -4937,36 +4958,15 @@
goto out;
}
- ret = ext4_alloc_file_blocks(file, lblk, max_blocks, flags, mode);
+ ret = ext4_alloc_file_blocks(file, lblk, max_blocks, new_size,
+ flags, mode);
if (ret)
goto out;
- handle = ext4_journal_start(inode, EXT4_HT_INODE, 2);
- if (IS_ERR(handle))
- goto out;
-
- tv = inode->i_ctime = ext4_current_time(inode);
-
- if (new_size) {
- if (new_size > i_size_read(inode)) {
- i_size_write(inode, new_size);
- inode->i_mtime = tv;
- }
- if (new_size > EXT4_I(inode)->i_disksize)
- ext4_update_i_disksize(inode, new_size);
- } else {
- /*
- * Mark that we allocate beyond EOF so the subsequent truncate
- * can proceed even if the new size is the same as i_size.
- */
- if ((offset + len) > i_size_read(inode))
- ext4_set_inode_flag(inode, EXT4_INODE_EOFBLOCKS);
+ if (file->f_flags & O_SYNC && EXT4_SB(inode->i_sb)->s_journal) {
+ ret = jbd2_complete_transaction(EXT4_SB(inode->i_sb)->s_journal,
+ EXT4_I(inode)->i_sync_tid);
}
- ext4_mark_inode_dirty(handle, inode);
- if (file->f_flags & O_SYNC)
- ext4_handle_sync(handle);
-
- ext4_journal_stop(handle);
out:
mutex_unlock(&inode->i_mutex);
trace_ext4_fallocate_exit(inode, offset, max_blocks, ret);
diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c
index 367a60c..3aa26e9 100644
--- a/fs/ext4/inode.c
+++ b/fs/ext4/inode.c
@@ -1055,27 +1055,11 @@
} else
copied = block_write_end(file, mapping, pos,
len, copied, page, fsdata);
-
/*
- * No need to use i_size_read() here, the i_size
- * cannot change under us because we hole i_mutex.
- *
- * But it's important to update i_size while still holding page lock:
+ * it's important to update i_size while still holding page lock:
* page writeout could otherwise come in and zero beyond i_size.
*/
- if (pos + copied > inode->i_size) {
- i_size_write(inode, pos + copied);
- i_size_changed = 1;
- }
-
- if (pos + copied > EXT4_I(inode)->i_disksize) {
- /* We need to mark inode dirty even if
- * new_i_size is less that inode->i_size
- * but greater than i_disksize. (hint delalloc)
- */
- ext4_update_i_disksize(inode, (pos + copied));
- i_size_changed = 1;
- }
+ i_size_changed = ext4_update_inode_size(inode, pos + copied);
unlock_page(page);
page_cache_release(page);
@@ -1123,7 +1107,7 @@
int ret = 0, ret2;
int partial = 0;
unsigned from, to;
- loff_t new_i_size;
+ int size_changed = 0;
trace_ext4_journalled_write_end(inode, pos, len, copied);
from = pos & (PAGE_CACHE_SIZE - 1);
@@ -1146,20 +1130,18 @@
if (!partial)
SetPageUptodate(page);
}
- new_i_size = pos + copied;
- if (new_i_size > inode->i_size)
- i_size_write(inode, pos+copied);
+ size_changed = ext4_update_inode_size(inode, pos + copied);
ext4_set_inode_state(inode, EXT4_STATE_JDATA);
EXT4_I(inode)->i_datasync_tid = handle->h_transaction->t_tid;
- if (new_i_size > EXT4_I(inode)->i_disksize) {
- ext4_update_i_disksize(inode, new_i_size);
+ unlock_page(page);
+ page_cache_release(page);
+
+ if (size_changed) {
ret2 = ext4_mark_inode_dirty(handle, inode);
if (!ret)
ret = ret2;
}
- unlock_page(page);
- page_cache_release(page);
if (pos + len > inode->i_size && ext4_can_truncate(inode))
/* if we have allocated more blocks and copied
* less. We will have blocks allocated outside
@@ -2095,6 +2077,7 @@
struct ext4_map_blocks *map = &mpd->map;
int err;
loff_t disksize;
+ int progress = 0;
mpd->io_submit.io_end->offset =
((loff_t)map->m_lblk) << inode->i_blkbits;
@@ -2111,8 +2094,11 @@
* is non-zero, a commit should free up blocks.
*/
if ((err == -ENOMEM) ||
- (err == -ENOSPC && ext4_count_free_clusters(sb)))
+ (err == -ENOSPC && ext4_count_free_clusters(sb))) {
+ if (progress)
+ goto update_disksize;
return err;
+ }
ext4_msg(sb, KERN_CRIT,
"Delayed block allocation failed for "
"inode %lu at logical offset %llu with"
@@ -2129,15 +2115,17 @@
*give_up_on_write = true;
return err;
}
+ progress = 1;
/*
* Update buffer state, submit mapped pages, and get us new
* extent to map
*/
err = mpage_map_and_submit_buffers(mpd);
if (err < 0)
- return err;
+ goto update_disksize;
} while (map->m_len);
+update_disksize:
/*
* Update on-disk size after IO is submitted. Races with
* truncate are avoided by checking i_size under i_data_sem.
diff --git a/fs/ext4/mballoc.c b/fs/ext4/mballoc.c
index 9560277..8b0f9ef 100644
--- a/fs/ext4/mballoc.c
+++ b/fs/ext4/mballoc.c
@@ -1412,6 +1412,8 @@
int last = first + count - 1;
struct super_block *sb = e4b->bd_sb;
+ if (WARN_ON(count == 0))
+ return;
BUG_ON(last >= (sb->s_blocksize << 3));
assert_spin_locked(ext4_group_lock_ptr(sb, e4b->bd_group));
/* Don't bother if the block group is corrupt. */
@@ -3221,6 +3223,8 @@
int err;
if (pa == NULL) {
+ if (ac->ac_f_ex.fe_len == 0)
+ return;
err = ext4_mb_load_buddy(ac->ac_sb, ac->ac_f_ex.fe_group, &e4b);
if (err) {
/*
@@ -3235,6 +3239,7 @@
mb_free_blocks(ac->ac_inode, &e4b, ac->ac_f_ex.fe_start,
ac->ac_f_ex.fe_len);
ext4_unlock_group(ac->ac_sb, ac->ac_f_ex.fe_group);
+ ext4_mb_unload_buddy(&e4b);
return;
}
if (pa->pa_type == MB_INODE_PA)
diff --git a/fs/ext4/namei.c b/fs/ext4/namei.c
index b147a67..90a3cdc 100644
--- a/fs/ext4/namei.c
+++ b/fs/ext4/namei.c
@@ -1227,7 +1227,7 @@
buffer */
int num = 0;
ext4_lblk_t nblocks;
- int i, err;
+ int i, err = 0;
int namelen;
*res_dir = NULL;
@@ -1264,7 +1264,11 @@
* return. Otherwise, fall back to doing a search the
* old fashioned way.
*/
- if (bh || (err != ERR_BAD_DX_DIR))
+ if (err == -ENOENT)
+ return NULL;
+ if (err && err != ERR_BAD_DX_DIR)
+ return ERR_PTR(err);
+ if (bh)
return bh;
dxtrace(printk(KERN_DEBUG "ext4_find_entry: dx failed, "
"falling back\n"));
@@ -1295,6 +1299,11 @@
}
num++;
bh = ext4_getblk(NULL, dir, b++, 0, &err);
+ if (unlikely(err)) {
+ if (ra_max == 0)
+ return ERR_PTR(err);
+ break;
+ }
bh_use[ra_max] = bh;
if (bh)
ll_rw_block(READ | REQ_META | REQ_PRIO,
@@ -1417,6 +1426,8 @@
return ERR_PTR(-ENAMETOOLONG);
bh = ext4_find_entry(dir, &dentry->d_name, &de, NULL);
+ if (IS_ERR(bh))
+ return (struct dentry *) bh;
inode = NULL;
if (bh) {
__u32 ino = le32_to_cpu(de->inode);
@@ -1450,6 +1461,8 @@
struct buffer_head *bh;
bh = ext4_find_entry(child->d_inode, &dotdot, &de, NULL);
+ if (IS_ERR(bh))
+ return (struct dentry *) bh;
if (!bh)
return ERR_PTR(-ENOENT);
ino = le32_to_cpu(de->inode);
@@ -2727,6 +2740,8 @@
retval = -ENOENT;
bh = ext4_find_entry(dir, &dentry->d_name, &de, NULL);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
if (!bh)
goto end_rmdir;
@@ -2794,6 +2809,8 @@
retval = -ENOENT;
bh = ext4_find_entry(dir, &dentry->d_name, &de, NULL);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
if (!bh)
goto end_unlink;
@@ -3121,6 +3138,8 @@
struct ext4_dir_entry_2 *de;
bh = ext4_find_entry(dir, d_name, &de, NULL);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
if (bh) {
retval = ext4_delete_entry(handle, dir, de, bh);
brelse(bh);
@@ -3128,7 +3147,8 @@
return retval;
}
-static void ext4_rename_delete(handle_t *handle, struct ext4_renament *ent)
+static void ext4_rename_delete(handle_t *handle, struct ext4_renament *ent,
+ int force_reread)
{
int retval;
/*
@@ -3140,7 +3160,8 @@
if (le32_to_cpu(ent->de->inode) != ent->inode->i_ino ||
ent->de->name_len != ent->dentry->d_name.len ||
strncmp(ent->de->name, ent->dentry->d_name.name,
- ent->de->name_len)) {
+ ent->de->name_len) ||
+ force_reread) {
retval = ext4_find_delete_entry(handle, ent->dir,
&ent->dentry->d_name);
} else {
@@ -3191,6 +3212,7 @@
.dentry = new_dentry,
.inode = new_dentry->d_inode,
};
+ int force_reread;
int retval;
dquot_initialize(old.dir);
@@ -3202,6 +3224,8 @@
dquot_initialize(new.inode);
old.bh = ext4_find_entry(old.dir, &old.dentry->d_name, &old.de, NULL);
+ if (IS_ERR(old.bh))
+ return PTR_ERR(old.bh);
/*
* Check for inode number is _not_ due to possible IO errors.
* We might rmdir the source, keep it as pwd of some process
@@ -3214,6 +3238,10 @@
new.bh = ext4_find_entry(new.dir, &new.dentry->d_name,
&new.de, &new.inlined);
+ if (IS_ERR(new.bh)) {
+ retval = PTR_ERR(new.bh);
+ goto end_rename;
+ }
if (new.bh) {
if (!new.inode) {
brelse(new.bh);
@@ -3246,6 +3274,15 @@
if (retval)
goto end_rename;
}
+ /*
+ * If we're renaming a file within an inline_data dir and adding or
+ * setting the new dirent causes a conversion from inline_data to
+ * extents/blockmap, we need to force the dirent delete code to
+ * re-read the directory, or else we end up trying to delete a dirent
+ * from what is now the extent tree root (or a block map).
+ */
+ force_reread = (new.dir->i_ino == old.dir->i_ino &&
+ ext4_test_inode_flag(new.dir, EXT4_INODE_INLINE_DATA));
if (!new.bh) {
retval = ext4_add_entry(handle, new.dentry, old.inode);
if (retval)
@@ -3256,6 +3293,9 @@
if (retval)
goto end_rename;
}
+ if (force_reread)
+ force_reread = !ext4_test_inode_flag(new.dir,
+ EXT4_INODE_INLINE_DATA);
/*
* Like most other Unix systems, set the ctime for inodes on a
@@ -3267,7 +3307,7 @@
/*
* ok, that's it
*/
- ext4_rename_delete(handle, &old);
+ ext4_rename_delete(handle, &old, force_reread);
if (new.inode) {
ext4_dec_count(handle, new.inode);
@@ -3330,6 +3370,8 @@
old.bh = ext4_find_entry(old.dir, &old.dentry->d_name,
&old.de, &old.inlined);
+ if (IS_ERR(old.bh))
+ return PTR_ERR(old.bh);
/*
* Check for inode number is _not_ due to possible IO errors.
* We might rmdir the source, keep it as pwd of some process
@@ -3342,6 +3384,10 @@
new.bh = ext4_find_entry(new.dir, &new.dentry->d_name,
&new.de, &new.inlined);
+ if (IS_ERR(new.bh)) {
+ retval = PTR_ERR(new.bh);
+ goto end_rename;
+ }
/* RENAME_EXCHANGE case: old *and* new must both exist */
if (!new.bh || le32_to_cpu(new.de->inode) != new.inode->i_ino)
diff --git a/fs/ext4/super.c b/fs/ext4/super.c
index 32b43ad..0b28b36 100644
--- a/fs/ext4/super.c
+++ b/fs/ext4/super.c
@@ -3181,9 +3181,9 @@
if (EXT4_HAS_RO_COMPAT_FEATURE(sb,
EXT4_FEATURE_RO_COMPAT_METADATA_CSUM)) {
- /* journal checksum v2 */
+ /* journal checksum v3 */
compat = 0;
- incompat = JBD2_FEATURE_INCOMPAT_CSUM_V2;
+ incompat = JBD2_FEATURE_INCOMPAT_CSUM_V3;
} else {
/* journal checksum v1 */
compat = JBD2_FEATURE_COMPAT_CHECKSUM;
@@ -3205,6 +3205,7 @@
jbd2_journal_clear_features(sbi->s_journal,
JBD2_FEATURE_COMPAT_CHECKSUM, 0,
JBD2_FEATURE_INCOMPAT_ASYNC_COMMIT |
+ JBD2_FEATURE_INCOMPAT_CSUM_V3 |
JBD2_FEATURE_INCOMPAT_CSUM_V2);
}
diff --git a/fs/jbd2/commit.c b/fs/jbd2/commit.c
index 6fac743..b73e021 100644
--- a/fs/jbd2/commit.c
+++ b/fs/jbd2/commit.c
@@ -97,7 +97,7 @@
struct commit_header *h;
__u32 csum;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return;
h = (struct commit_header *)(bh->b_data);
@@ -313,11 +313,11 @@
return checksum;
}
-static void write_tag_block(int tag_bytes, journal_block_tag_t *tag,
+static void write_tag_block(journal_t *j, journal_block_tag_t *tag,
unsigned long long block)
{
tag->t_blocknr = cpu_to_be32(block & (u32)~0);
- if (tag_bytes > JBD2_TAG_SIZE32)
+ if (JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_64BIT))
tag->t_blocknr_high = cpu_to_be32((block >> 31) >> 1);
}
@@ -327,7 +327,7 @@
struct jbd2_journal_block_tail *tail;
__u32 csum;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return;
tail = (struct jbd2_journal_block_tail *)(bh->b_data + j->j_blocksize -
@@ -340,12 +340,13 @@
static void jbd2_block_tag_csum_set(journal_t *j, journal_block_tag_t *tag,
struct buffer_head *bh, __u32 sequence)
{
+ journal_block_tag3_t *tag3 = (journal_block_tag3_t *)tag;
struct page *page = bh->b_page;
__u8 *addr;
__u32 csum32;
__be32 seq;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return;
seq = cpu_to_be32(sequence);
@@ -355,8 +356,10 @@
bh->b_size);
kunmap_atomic(addr);
- /* We only have space to store the lower 16 bits of the crc32c. */
- tag->t_checksum = cpu_to_be16(csum32);
+ if (JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V3))
+ tag3->t_checksum = cpu_to_be32(csum32);
+ else
+ tag->t_checksum = cpu_to_be16(csum32);
}
/*
* jbd2_journal_commit_transaction
@@ -396,7 +399,7 @@
LIST_HEAD(io_bufs);
LIST_HEAD(log_bufs);
- if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
csum_size = sizeof(struct jbd2_journal_block_tail);
/*
@@ -690,7 +693,7 @@
tag_flag |= JBD2_FLAG_SAME_UUID;
tag = (journal_block_tag_t *) tagp;
- write_tag_block(tag_bytes, tag, jh2bh(jh)->b_blocknr);
+ write_tag_block(journal, tag, jh2bh(jh)->b_blocknr);
tag->t_flags = cpu_to_be16(tag_flag);
jbd2_block_tag_csum_set(journal, tag, wbuf[bufs],
commit_transaction->t_tid);
diff --git a/fs/jbd2/journal.c b/fs/jbd2/journal.c
index 67b8e30..19d74d8 100644
--- a/fs/jbd2/journal.c
+++ b/fs/jbd2/journal.c
@@ -124,7 +124,7 @@
/* Checksumming functions */
static int jbd2_verify_csum_type(journal_t *j, journal_superblock_t *sb)
{
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
return sb->s_checksum_type == JBD2_CRC32C_CHKSUM;
@@ -145,7 +145,7 @@
static int jbd2_superblock_csum_verify(journal_t *j, journal_superblock_t *sb)
{
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
return sb->s_checksum == jbd2_superblock_csum(j, sb);
@@ -153,7 +153,7 @@
static void jbd2_superblock_csum_set(journal_t *j, journal_superblock_t *sb)
{
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return;
sb->s_checksum = jbd2_superblock_csum(j, sb);
@@ -1522,21 +1522,29 @@
goto out;
}
- if (JBD2_HAS_COMPAT_FEATURE(journal, JBD2_FEATURE_COMPAT_CHECKSUM) &&
- JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2)) {
+ if (jbd2_journal_has_csum_v2or3(journal) &&
+ JBD2_HAS_COMPAT_FEATURE(journal, JBD2_FEATURE_COMPAT_CHECKSUM)) {
/* Can't have checksum v1 and v2 on at the same time! */
printk(KERN_ERR "JBD2: Can't enable checksumming v1 and v2 "
"at the same time!\n");
goto out;
}
+ if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2) &&
+ JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V3)) {
+ /* Can't have checksum v2 and v3 at the same time! */
+ printk(KERN_ERR "JBD2: Can't enable checksumming v2 and v3 "
+ "at the same time!\n");
+ goto out;
+ }
+
if (!jbd2_verify_csum_type(journal, sb)) {
printk(KERN_ERR "JBD2: Unknown checksum type\n");
goto out;
}
/* Load the checksum driver */
- if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2)) {
+ if (jbd2_journal_has_csum_v2or3(journal)) {
journal->j_chksum_driver = crypto_alloc_shash("crc32c", 0, 0);
if (IS_ERR(journal->j_chksum_driver)) {
printk(KERN_ERR "JBD2: Cannot load crc32c driver.\n");
@@ -1553,7 +1561,7 @@
}
/* Precompute checksum seed for all metadata */
- if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
journal->j_csum_seed = jbd2_chksum(journal, ~0, sb->s_uuid,
sizeof(sb->s_uuid));
@@ -1813,8 +1821,14 @@
if (!jbd2_journal_check_available_features(journal, compat, ro, incompat))
return 0;
- /* Asking for checksumming v2 and v1? Only give them v2. */
- if (incompat & JBD2_FEATURE_INCOMPAT_CSUM_V2 &&
+ /* If enabling v2 checksums, turn on v3 instead */
+ if (incompat & JBD2_FEATURE_INCOMPAT_CSUM_V2) {
+ incompat &= ~JBD2_FEATURE_INCOMPAT_CSUM_V2;
+ incompat |= JBD2_FEATURE_INCOMPAT_CSUM_V3;
+ }
+
+ /* Asking for checksumming v3 and v1? Only give them v3. */
+ if (incompat & JBD2_FEATURE_INCOMPAT_CSUM_V3 &&
compat & JBD2_FEATURE_COMPAT_CHECKSUM)
compat &= ~JBD2_FEATURE_COMPAT_CHECKSUM;
@@ -1823,8 +1837,8 @@
sb = journal->j_superblock;
- /* If enabling v2 checksums, update superblock */
- if (INCOMPAT_FEATURE_ON(JBD2_FEATURE_INCOMPAT_CSUM_V2)) {
+ /* If enabling v3 checksums, update superblock */
+ if (INCOMPAT_FEATURE_ON(JBD2_FEATURE_INCOMPAT_CSUM_V3)) {
sb->s_checksum_type = JBD2_CRC32C_CHKSUM;
sb->s_feature_compat &=
~cpu_to_be32(JBD2_FEATURE_COMPAT_CHECKSUM);
@@ -1842,8 +1856,7 @@
}
/* Precompute checksum seed for all metadata */
- if (JBD2_HAS_INCOMPAT_FEATURE(journal,
- JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
journal->j_csum_seed = jbd2_chksum(journal, ~0,
sb->s_uuid,
sizeof(sb->s_uuid));
@@ -1852,7 +1865,8 @@
/* If enabling v1 checksums, downgrade superblock */
if (COMPAT_FEATURE_ON(JBD2_FEATURE_COMPAT_CHECKSUM))
sb->s_feature_incompat &=
- ~cpu_to_be32(JBD2_FEATURE_INCOMPAT_CSUM_V2);
+ ~cpu_to_be32(JBD2_FEATURE_INCOMPAT_CSUM_V2 |
+ JBD2_FEATURE_INCOMPAT_CSUM_V3);
sb->s_feature_compat |= cpu_to_be32(compat);
sb->s_feature_ro_compat |= cpu_to_be32(ro);
@@ -2165,16 +2179,20 @@
*/
size_t journal_tag_bytes(journal_t *journal)
{
- journal_block_tag_t tag;
- size_t x = 0;
+ size_t sz;
+
+ if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V3))
+ return sizeof(journal_block_tag3_t);
+
+ sz = sizeof(journal_block_tag_t);
if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2))
- x += sizeof(tag.t_checksum);
+ sz += sizeof(__u16);
if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_64BIT))
- return x + JBD2_TAG_SIZE64;
+ return sz;
else
- return x + JBD2_TAG_SIZE32;
+ return sz - sizeof(__u32);
}
/*
diff --git a/fs/jbd2/recovery.c b/fs/jbd2/recovery.c
index 3b6bb19..9b329b5 100644
--- a/fs/jbd2/recovery.c
+++ b/fs/jbd2/recovery.c
@@ -181,7 +181,7 @@
__be32 provided;
__u32 calculated;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
tail = (struct jbd2_journal_block_tail *)(buf + j->j_blocksize -
@@ -205,7 +205,7 @@
int nr = 0, size = journal->j_blocksize;
int tag_bytes = journal_tag_bytes(journal);
- if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
size -= sizeof(struct jbd2_journal_block_tail);
tagp = &bh->b_data[sizeof(journal_header_t)];
@@ -338,10 +338,11 @@
return err;
}
-static inline unsigned long long read_tag_block(int tag_bytes, journal_block_tag_t *tag)
+static inline unsigned long long read_tag_block(journal_t *journal,
+ journal_block_tag_t *tag)
{
unsigned long long block = be32_to_cpu(tag->t_blocknr);
- if (tag_bytes > JBD2_TAG_SIZE32)
+ if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_64BIT))
block |= (u64)be32_to_cpu(tag->t_blocknr_high) << 32;
return block;
}
@@ -384,7 +385,7 @@
__be32 provided;
__u32 calculated;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
h = buf;
@@ -399,17 +400,21 @@
static int jbd2_block_tag_csum_verify(journal_t *j, journal_block_tag_t *tag,
void *buf, __u32 sequence)
{
+ journal_block_tag3_t *tag3 = (journal_block_tag3_t *)tag;
__u32 csum32;
__be32 seq;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
seq = cpu_to_be32(sequence);
csum32 = jbd2_chksum(j, j->j_csum_seed, (__u8 *)&seq, sizeof(seq));
csum32 = jbd2_chksum(j, csum32, buf, j->j_blocksize);
- return tag->t_checksum == cpu_to_be16(csum32);
+ if (JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V3))
+ return tag3->t_checksum == cpu_to_be32(csum32);
+ else
+ return tag->t_checksum == cpu_to_be16(csum32);
}
static int do_one_pass(journal_t *journal,
@@ -426,6 +431,7 @@
int tag_bytes = journal_tag_bytes(journal);
__u32 crc32_sum = ~0; /* Transactional Checksums */
int descr_csum_size = 0;
+ int block_error = 0;
/*
* First thing is to establish what we expect to find in the log
@@ -512,8 +518,7 @@
switch(blocktype) {
case JBD2_DESCRIPTOR_BLOCK:
/* Verify checksum first */
- if (JBD2_HAS_INCOMPAT_FEATURE(journal,
- JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
descr_csum_size =
sizeof(struct jbd2_journal_block_tail);
if (descr_csum_size > 0 &&
@@ -574,7 +579,7 @@
unsigned long long blocknr;
J_ASSERT(obh != NULL);
- blocknr = read_tag_block(tag_bytes,
+ blocknr = read_tag_block(journal,
tag);
/* If the block has been
@@ -598,7 +603,8 @@
"checksum recovering "
"block %llu in log\n",
blocknr);
- continue;
+ block_error = 1;
+ goto skip_write;
}
/* Find a buffer for the new
@@ -797,7 +803,8 @@
success = -EIO;
}
}
-
+ if (block_error && success == 0)
+ success = -EIO;
return success;
failed:
@@ -811,7 +818,7 @@
__be32 provided;
__u32 calculated;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return 1;
tail = (struct jbd2_journal_revoke_tail *)(buf + j->j_blocksize -
diff --git a/fs/jbd2/revoke.c b/fs/jbd2/revoke.c
index 198c9c1..d5e95a1 100644
--- a/fs/jbd2/revoke.c
+++ b/fs/jbd2/revoke.c
@@ -91,8 +91,8 @@
#include <linux/list.h>
#include <linux/init.h>
#include <linux/bio.h>
-#endif
#include <linux/log2.h>
+#endif
static struct kmem_cache *jbd2_revoke_record_cache;
static struct kmem_cache *jbd2_revoke_table_cache;
@@ -597,7 +597,7 @@
offset = *offsetp;
/* Do we need to leave space at the end for a checksum? */
- if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (jbd2_journal_has_csum_v2or3(journal))
csum_size = sizeof(struct jbd2_journal_revoke_tail);
/* Make sure we have a descriptor with space left for the record */
@@ -644,7 +644,7 @@
struct jbd2_journal_revoke_tail *tail;
__u32 csum;
- if (!JBD2_HAS_INCOMPAT_FEATURE(j, JBD2_FEATURE_INCOMPAT_CSUM_V2))
+ if (!jbd2_journal_has_csum_v2or3(j))
return;
tail = (struct jbd2_journal_revoke_tail *)(bh->b_data + j->j_blocksize -
diff --git a/fs/locks.c b/fs/locks.c
index cb66fb0..bb08857 100644
--- a/fs/locks.c
+++ b/fs/locks.c
@@ -1619,7 +1619,7 @@
smp_mb();
error = check_conflicting_open(dentry, arg);
if (error)
- locks_unlink_lock(flp);
+ locks_unlink_lock(before);
out:
if (is_deleg)
mutex_unlock(&inode->i_mutex);
diff --git a/fs/nfs/nfs3acl.c b/fs/nfs/nfs3acl.c
index d0fec26..24c6898 100644
--- a/fs/nfs/nfs3acl.c
+++ b/fs/nfs/nfs3acl.c
@@ -129,7 +129,10 @@
.rpc_argp = &args,
.rpc_resp = &fattr,
};
- int status;
+ int status = 0;
+
+ if (acl == NULL && (!S_ISDIR(inode->i_mode) || dfacl == NULL))
+ goto out;
status = -EOPNOTSUPP;
if (!nfs_server_capable(inode, NFS_CAP_ACLS))
diff --git a/fs/nfs/nfs4proc.c b/fs/nfs/nfs4proc.c
index 75ae8d2..7dd8aca 100644
--- a/fs/nfs/nfs4proc.c
+++ b/fs/nfs/nfs4proc.c
@@ -2560,6 +2560,7 @@
struct nfs4_closedata *calldata = data;
struct nfs4_state *state = calldata->state;
struct nfs_server *server = NFS_SERVER(calldata->inode);
+ nfs4_stateid *res_stateid = NULL;
dprintk("%s: begin!\n", __func__);
if (!nfs4_sequence_done(task, &calldata->res.seq_res))
@@ -2570,12 +2571,12 @@
*/
switch (task->tk_status) {
case 0:
- if (calldata->roc)
+ res_stateid = &calldata->res.stateid;
+ if (calldata->arg.fmode == 0 && calldata->roc)
pnfs_roc_set_barrier(state->inode,
calldata->roc_barrier);
- nfs_clear_open_stateid(state, &calldata->res.stateid, 0);
renew_lease(server, calldata->timestamp);
- goto out_release;
+ break;
case -NFS4ERR_ADMIN_REVOKED:
case -NFS4ERR_STALE_STATEID:
case -NFS4ERR_OLD_STATEID:
@@ -2589,7 +2590,7 @@
goto out_release;
}
}
- nfs_clear_open_stateid(state, NULL, calldata->arg.fmode);
+ nfs_clear_open_stateid(state, res_stateid, calldata->arg.fmode);
out_release:
nfs_release_seqid(calldata->arg.seqid);
nfs_refresh_inode(calldata->inode, calldata->res.fattr);
@@ -2601,6 +2602,7 @@
struct nfs4_closedata *calldata = data;
struct nfs4_state *state = calldata->state;
struct inode *inode = calldata->inode;
+ bool is_rdonly, is_wronly, is_rdwr;
int call_close = 0;
dprintk("%s: begin!\n", __func__);
@@ -2608,18 +2610,24 @@
goto out_wait;
task->tk_msg.rpc_proc = &nfs4_procedures[NFSPROC4_CLNT_OPEN_DOWNGRADE];
- calldata->arg.fmode = FMODE_READ|FMODE_WRITE;
spin_lock(&state->owner->so_lock);
+ is_rdwr = test_bit(NFS_O_RDWR_STATE, &state->flags);
+ is_rdonly = test_bit(NFS_O_RDONLY_STATE, &state->flags);
+ is_wronly = test_bit(NFS_O_WRONLY_STATE, &state->flags);
+ /* Calculate the current open share mode */
+ calldata->arg.fmode = 0;
+ if (is_rdonly || is_rdwr)
+ calldata->arg.fmode |= FMODE_READ;
+ if (is_wronly || is_rdwr)
+ calldata->arg.fmode |= FMODE_WRITE;
/* Calculate the change in open mode */
if (state->n_rdwr == 0) {
if (state->n_rdonly == 0) {
- call_close |= test_bit(NFS_O_RDONLY_STATE, &state->flags);
- call_close |= test_bit(NFS_O_RDWR_STATE, &state->flags);
+ call_close |= is_rdonly || is_rdwr;
calldata->arg.fmode &= ~FMODE_READ;
}
if (state->n_wronly == 0) {
- call_close |= test_bit(NFS_O_WRONLY_STATE, &state->flags);
- call_close |= test_bit(NFS_O_RDWR_STATE, &state->flags);
+ call_close |= is_wronly || is_rdwr;
calldata->arg.fmode &= ~FMODE_WRITE;
}
}
diff --git a/fs/ocfs2/cluster/quorum.c b/fs/ocfs2/cluster/quorum.c
index 1ec141e..62e8ec6 100644
--- a/fs/ocfs2/cluster/quorum.c
+++ b/fs/ocfs2/cluster/quorum.c
@@ -160,9 +160,18 @@
}
out:
- spin_unlock(&qs->qs_lock);
- if (fence)
+ if (fence) {
+ spin_unlock(&qs->qs_lock);
o2quo_fence_self();
+ } else {
+ mlog(ML_NOTICE, "not fencing this node, heartbeating: %d, "
+ "connected: %d, lowest: %d (%sreachable)\n",
+ qs->qs_heartbeating, qs->qs_connected, lowest_hb,
+ lowest_reachable ? "" : "un");
+ spin_unlock(&qs->qs_lock);
+
+ }
+
}
static void o2quo_set_hold(struct o2quo_state *qs, u8 node)
diff --git a/fs/ocfs2/cluster/tcp.c b/fs/ocfs2/cluster/tcp.c
index 681691b..ea34952 100644
--- a/fs/ocfs2/cluster/tcp.c
+++ b/fs/ocfs2/cluster/tcp.c
@@ -1480,6 +1480,14 @@
return ret;
}
+static int o2net_set_usertimeout(struct socket *sock)
+{
+ int user_timeout = O2NET_TCP_USER_TIMEOUT;
+
+ return kernel_setsockopt(sock, SOL_TCP, TCP_USER_TIMEOUT,
+ (char *)&user_timeout, sizeof(user_timeout));
+}
+
static void o2net_initialize_handshake(void)
{
o2net_hand->o2hb_heartbeat_timeout_ms = cpu_to_be32(
@@ -1536,16 +1544,20 @@
#endif
printk(KERN_NOTICE "o2net: Connection to " SC_NODEF_FMT " has been "
- "idle for %lu.%lu secs, shutting it down.\n", SC_NODEF_ARGS(sc),
- msecs / 1000, msecs % 1000);
+ "idle for %lu.%lu secs.\n",
+ SC_NODEF_ARGS(sc), msecs / 1000, msecs % 1000);
- /*
- * Initialize the nn_timeout so that the next connection attempt
- * will continue in o2net_start_connect.
+ /* idle timerout happen, don't shutdown the connection, but
+ * make fence decision. Maybe the connection can recover before
+ * the decision is made.
*/
atomic_set(&nn->nn_timeout, 1);
+ o2quo_conn_err(o2net_num_from_nn(nn));
+ queue_delayed_work(o2net_wq, &nn->nn_still_up,
+ msecs_to_jiffies(O2NET_QUORUM_DELAY_MS));
- o2net_sc_queue_work(sc, &sc->sc_shutdown_work);
+ o2net_sc_reset_idle_timer(sc);
+
}
static void o2net_sc_reset_idle_timer(struct o2net_sock_container *sc)
@@ -1560,6 +1572,15 @@
static void o2net_sc_postpone_idle(struct o2net_sock_container *sc)
{
+ struct o2net_node *nn = o2net_nn_from_num(sc->sc_node->nd_num);
+
+ /* clear fence decision since the connection recover from timeout*/
+ if (atomic_read(&nn->nn_timeout)) {
+ o2quo_conn_up(o2net_num_from_nn(nn));
+ cancel_delayed_work(&nn->nn_still_up);
+ atomic_set(&nn->nn_timeout, 0);
+ }
+
/* Only push out an existing timer */
if (timer_pending(&sc->sc_idle_timeout))
o2net_sc_reset_idle_timer(sc);
@@ -1650,6 +1671,12 @@
goto out;
}
+ ret = o2net_set_usertimeout(sock);
+ if (ret) {
+ mlog(ML_ERROR, "set TCP_USER_TIMEOUT failed with %d\n", ret);
+ goto out;
+ }
+
o2net_register_callbacks(sc->sc_sock->sk, sc);
spin_lock(&nn->nn_lock);
@@ -1831,6 +1858,12 @@
goto out;
}
+ ret = o2net_set_usertimeout(new_sock);
+ if (ret) {
+ mlog(ML_ERROR, "set TCP_USER_TIMEOUT failed with %d\n", ret);
+ goto out;
+ }
+
slen = sizeof(sin);
ret = new_sock->ops->getname(new_sock, (struct sockaddr *) &sin,
&slen, 1);
diff --git a/fs/ocfs2/cluster/tcp.h b/fs/ocfs2/cluster/tcp.h
index 5bada2a..c571e84 100644
--- a/fs/ocfs2/cluster/tcp.h
+++ b/fs/ocfs2/cluster/tcp.h
@@ -63,6 +63,7 @@
#define O2NET_KEEPALIVE_DELAY_MS_DEFAULT 2000
#define O2NET_IDLE_TIMEOUT_MS_DEFAULT 30000
+#define O2NET_TCP_USER_TIMEOUT 0x7fffffff
/* TODO: figure this out.... */
static inline int o2net_link_down(int err, struct socket *sock)
diff --git a/fs/ocfs2/ioctl.c b/fs/ocfs2/ioctl.c
index 6f66b37..53e6c40 100644
--- a/fs/ocfs2/ioctl.c
+++ b/fs/ocfs2/ioctl.c
@@ -35,9 +35,8 @@
copy_to_user((typeof(a) __user *)b, &(a), sizeof(a))
/*
- * This call is void because we are already reporting an error that may
- * be -EFAULT. The error will be returned from the ioctl(2) call. It's
- * just a best-effort to tell userspace that this request caused the error.
+ * This is just a best-effort to tell userspace that this request
+ * caused the error.
*/
static inline void o2info_set_request_error(struct ocfs2_info_request *kreq,
struct ocfs2_info_request __user *req)
@@ -146,136 +145,105 @@
static int ocfs2_info_handle_blocksize(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_blocksize oib;
if (o2info_from_user(oib, req))
- goto bail;
+ return -EFAULT;
oib.ib_blocksize = inode->i_sb->s_blocksize;
o2info_set_request_filled(&oib.ib_req);
if (o2info_to_user(oib, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oib.ib_req, req);
-
- return status;
+ return 0;
}
static int ocfs2_info_handle_clustersize(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_clustersize oic;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oic, req))
- goto bail;
+ return -EFAULT;
oic.ic_clustersize = osb->s_clustersize;
o2info_set_request_filled(&oic.ic_req);
if (o2info_to_user(oic, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oic.ic_req, req);
-
- return status;
+ return 0;
}
static int ocfs2_info_handle_maxslots(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_maxslots oim;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oim, req))
- goto bail;
+ return -EFAULT;
oim.im_max_slots = osb->max_slots;
o2info_set_request_filled(&oim.im_req);
if (o2info_to_user(oim, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oim.im_req, req);
-
- return status;
+ return 0;
}
static int ocfs2_info_handle_label(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_label oil;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oil, req))
- goto bail;
+ return -EFAULT;
memcpy(oil.il_label, osb->vol_label, OCFS2_MAX_VOL_LABEL_LEN);
o2info_set_request_filled(&oil.il_req);
if (o2info_to_user(oil, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oil.il_req, req);
-
- return status;
+ return 0;
}
static int ocfs2_info_handle_uuid(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_uuid oiu;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oiu, req))
- goto bail;
+ return -EFAULT;
memcpy(oiu.iu_uuid_str, osb->uuid_str, OCFS2_TEXT_UUID_LEN + 1);
o2info_set_request_filled(&oiu.iu_req);
if (o2info_to_user(oiu, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oiu.iu_req, req);
-
- return status;
+ return 0;
}
static int ocfs2_info_handle_fs_features(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_fs_features oif;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oif, req))
- goto bail;
+ return -EFAULT;
oif.if_compat_features = osb->s_feature_compat;
oif.if_incompat_features = osb->s_feature_incompat;
@@ -284,39 +252,28 @@
o2info_set_request_filled(&oif.if_req);
if (o2info_to_user(oif, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oif.if_req, req);
-
- return status;
+ return 0;
}
static int ocfs2_info_handle_journal_size(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_journal_size oij;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
if (o2info_from_user(oij, req))
- goto bail;
+ return -EFAULT;
oij.ij_journal_size = i_size_read(osb->journal->j_inode);
o2info_set_request_filled(&oij.ij_req);
if (o2info_to_user(oij, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oij.ij_req, req);
-
- return status;
+ return 0;
}
static int ocfs2_info_scan_inode_alloc(struct ocfs2_super *osb,
@@ -373,7 +330,7 @@
u32 i;
u64 blkno = -1;
char namebuf[40];
- int status = -EFAULT, type = INODE_ALLOC_SYSTEM_INODE;
+ int status, type = INODE_ALLOC_SYSTEM_INODE;
struct ocfs2_info_freeinode *oifi = NULL;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
struct inode *inode_alloc = NULL;
@@ -385,8 +342,10 @@
goto out_err;
}
- if (o2info_from_user(*oifi, req))
- goto bail;
+ if (o2info_from_user(*oifi, req)) {
+ status = -EFAULT;
+ goto out_free;
+ }
oifi->ifi_slotnum = osb->max_slots;
@@ -424,14 +383,16 @@
o2info_set_request_filled(&oifi->ifi_req);
- if (o2info_to_user(*oifi, req))
- goto bail;
+ if (o2info_to_user(*oifi, req)) {
+ status = -EFAULT;
+ goto out_free;
+ }
status = 0;
bail:
if (status)
o2info_set_request_error(&oifi->ifi_req, req);
-
+out_free:
kfree(oifi);
out_err:
return status;
@@ -658,7 +619,7 @@
{
u64 blkno = -1;
char namebuf[40];
- int status = -EFAULT, type = GLOBAL_BITMAP_SYSTEM_INODE;
+ int status, type = GLOBAL_BITMAP_SYSTEM_INODE;
struct ocfs2_info_freefrag *oiff;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
@@ -671,8 +632,10 @@
goto out_err;
}
- if (o2info_from_user(*oiff, req))
- goto bail;
+ if (o2info_from_user(*oiff, req)) {
+ status = -EFAULT;
+ goto out_free;
+ }
/*
* chunksize from userspace should be power of 2.
*/
@@ -711,14 +674,14 @@
if (o2info_to_user(*oiff, req)) {
status = -EFAULT;
- goto bail;
+ goto out_free;
}
status = 0;
bail:
if (status)
o2info_set_request_error(&oiff->iff_req, req);
-
+out_free:
kfree(oiff);
out_err:
return status;
@@ -727,23 +690,17 @@
static int ocfs2_info_handle_unknown(struct inode *inode,
struct ocfs2_info_request __user *req)
{
- int status = -EFAULT;
struct ocfs2_info_request oir;
if (o2info_from_user(oir, req))
- goto bail;
+ return -EFAULT;
o2info_clear_request_filled(&oir);
if (o2info_to_user(oir, req))
- goto bail;
+ return -EFAULT;
- status = 0;
-bail:
- if (status)
- o2info_set_request_error(&oir, req);
-
- return status;
+ return 0;
}
/*
diff --git a/include/linux/blk-mq.h b/include/linux/blk-mq.h
index eb726b9..a1e31f2 100644
--- a/include/linux/blk-mq.h
+++ b/include/linux/blk-mq.h
@@ -127,10 +127,9 @@
BLK_MQ_RQ_QUEUE_ERROR = 2, /* end IO with error */
BLK_MQ_F_SHOULD_MERGE = 1 << 0,
- BLK_MQ_F_SHOULD_SORT = 1 << 1,
- BLK_MQ_F_TAG_SHARED = 1 << 2,
- BLK_MQ_F_SG_MERGE = 1 << 3,
- BLK_MQ_F_SYSFS_UP = 1 << 4,
+ BLK_MQ_F_TAG_SHARED = 1 << 1,
+ BLK_MQ_F_SG_MERGE = 1 << 2,
+ BLK_MQ_F_SYSFS_UP = 1 << 3,
BLK_MQ_S_STOPPED = 0,
BLK_MQ_S_TAG_ACTIVE = 1,
diff --git a/include/linux/jbd2.h b/include/linux/jbd2.h
index d5b50a1..0dae71e 100644
--- a/include/linux/jbd2.h
+++ b/include/linux/jbd2.h
@@ -159,7 +159,11 @@
* journal_block_tag (in the descriptor). The other h_chksum* fields are
* not used.
*
- * Checksum v1 and v2 are mutually exclusive features.
+ * If FEATURE_INCOMPAT_CSUM_V3 is set, the descriptor block uses
+ * journal_block_tag3_t to store a full 32-bit checksum. Everything else
+ * is the same as v2.
+ *
+ * Checksum v1, v2, and v3 are mutually exclusive features.
*/
struct commit_header {
__be32 h_magic;
@@ -179,6 +183,14 @@
* raw struct shouldn't be used for pointer math or sizeof() - use
* journal_tag_bytes(journal) instead to compute this.
*/
+typedef struct journal_block_tag3_s
+{
+ __be32 t_blocknr; /* The on-disk block number */
+ __be32 t_flags; /* See below */
+ __be32 t_blocknr_high; /* most-significant high 32bits. */
+ __be32 t_checksum; /* crc32c(uuid+seq+block) */
+} journal_block_tag3_t;
+
typedef struct journal_block_tag_s
{
__be32 t_blocknr; /* The on-disk block number */
@@ -187,9 +199,6 @@
__be32 t_blocknr_high; /* most-significant high 32bits. */
} journal_block_tag_t;
-#define JBD2_TAG_SIZE32 (offsetof(journal_block_tag_t, t_blocknr_high))
-#define JBD2_TAG_SIZE64 (sizeof(journal_block_tag_t))
-
/* Tail of descriptor block, for checksumming */
struct jbd2_journal_block_tail {
__be32 t_checksum; /* crc32c(uuid+descr_block) */
@@ -284,6 +293,7 @@
#define JBD2_FEATURE_INCOMPAT_64BIT 0x00000002
#define JBD2_FEATURE_INCOMPAT_ASYNC_COMMIT 0x00000004
#define JBD2_FEATURE_INCOMPAT_CSUM_V2 0x00000008
+#define JBD2_FEATURE_INCOMPAT_CSUM_V3 0x00000010
/* Features known to this kernel version: */
#define JBD2_KNOWN_COMPAT_FEATURES JBD2_FEATURE_COMPAT_CHECKSUM
@@ -291,7 +301,8 @@
#define JBD2_KNOWN_INCOMPAT_FEATURES (JBD2_FEATURE_INCOMPAT_REVOKE | \
JBD2_FEATURE_INCOMPAT_64BIT | \
JBD2_FEATURE_INCOMPAT_ASYNC_COMMIT | \
- JBD2_FEATURE_INCOMPAT_CSUM_V2)
+ JBD2_FEATURE_INCOMPAT_CSUM_V2 | \
+ JBD2_FEATURE_INCOMPAT_CSUM_V3)
#ifdef __KERNEL__
@@ -1296,6 +1307,15 @@
extern int jbd2_journal_blocks_per_page(struct inode *inode);
extern size_t journal_tag_bytes(journal_t *journal);
+static inline int jbd2_journal_has_csum_v2or3(journal_t *journal)
+{
+ if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V2) ||
+ JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_CSUM_V3))
+ return 1;
+
+ return 0;
+}
+
/*
* We reserve t_outstanding_credits >> JBD2_CONTROL_BLOCKS_SHIFT for
* transaction control blocks.
diff --git a/include/linux/seqno-fence.h b/include/linux/seqno-fence.h
index 3d6003d..a1ba6a5 100644
--- a/include/linux/seqno-fence.h
+++ b/include/linux/seqno-fence.h
@@ -62,6 +62,7 @@
* @context: the execution context this fence is a part of
* @seqno_ofs: the offset within @sync_buf
* @seqno: the sequence # to signal on
+ * @cond: fence wait condition
* @ops: the fence_ops for operations on this seqno fence
*
* This function initializes a struct seqno_fence with passed parameters,
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index e713543..46d188a 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -253,6 +253,7 @@
* the device whose settings are being modified.
* @transfer: adds a message to the controller's transfer queue.
* @cleanup: frees controller-specific state
+ * @can_dma: determine whether this master supports DMA
* @queued: whether this master is providing an internal message queue
* @kworker: thread struct for message pump
* @kworker_task: pointer to task for message pump kworker thread
@@ -262,6 +263,7 @@
* @cur_msg: the currently in-flight message
* @cur_msg_prepared: spi_prepare_message was called for the currently
* in-flight message
+ * @cur_msg_mapped: message has been mapped for DMA
* @xfer_completion: used by core transfer_one_message()
* @busy: message pump is busy
* @running: message pump is running
@@ -299,6 +301,10 @@
* @cs_gpios: Array of GPIOs to use as chip select lines; one per CS
* number. Any individual value may be -ENOENT for CS lines that
* are not GPIOs (driven by the SPI controller itself).
+ * @dma_tx: DMA transmit channel
+ * @dma_rx: DMA receive channel
+ * @dummy_rx: dummy receive buffer for full-duplex devices
+ * @dummy_tx: dummy transmit buffer for full-duplex devices
*
* Each SPI master controller can communicate with one or more @spi_device
* children. These make a small bus, sharing MOSI, MISO and SCK signals
@@ -632,6 +638,7 @@
* addresses for each transfer buffer
* @complete: called to report transaction completions
* @context: the argument to complete() when it's called
+ * @frame_length: the total number of bytes in the message
* @actual_length: the total number of bytes that were transferred in all
* successful segments
* @status: zero for success, else negative errno
diff --git a/drivers/staging/usbip/uapi/usbip.h b/include/uapi/linux/usbip.h
similarity index 100%
rename from drivers/staging/usbip/uapi/usbip.h
rename to include/uapi/linux/usbip.h
diff --git a/include/uapi/linux/xattr.h b/include/uapi/linux/xattr.h
index c38355c..1590c49 100644
--- a/include/uapi/linux/xattr.h
+++ b/include/uapi/linux/xattr.h
@@ -13,7 +13,7 @@
#ifndef _UAPI_LINUX_XATTR_H
#define _UAPI_LINUX_XATTR_H
-#ifdef __UAPI_DEF_XATTR
+#if __UAPI_DEF_XATTR
#define __USE_KERNEL_XATTR_DEFS
#define XATTR_CREATE 0x1 /* set value, fail if attr already exists */
diff --git a/kernel/kexec.c b/kernel/kexec.c
index 0b49a0a..2bee072 100644
--- a/kernel/kexec.c
+++ b/kernel/kexec.c
@@ -64,7 +64,9 @@
char __weak kexec_purgatory[0];
size_t __weak kexec_purgatory_size = 0;
+#ifdef CONFIG_KEXEC_FILE
static int kexec_calculate_store_digests(struct kimage *image);
+#endif
/* Location of the reserved area for the crash kernel */
struct resource crashk_res = {
@@ -341,6 +343,7 @@
return ret;
}
+#ifdef CONFIG_KEXEC_FILE
static int copy_file_from_fd(int fd, void **buf, unsigned long *buf_len)
{
struct fd f = fdget(fd);
@@ -612,6 +615,9 @@
kfree(image);
return ret;
}
+#else /* CONFIG_KEXEC_FILE */
+static inline void kimage_file_post_load_cleanup(struct kimage *image) { }
+#endif /* CONFIG_KEXEC_FILE */
static int kimage_is_destination_range(struct kimage *image,
unsigned long start,
@@ -1375,6 +1381,7 @@
}
#endif
+#ifdef CONFIG_KEXEC_FILE
SYSCALL_DEFINE5(kexec_file_load, int, kernel_fd, int, initrd_fd,
unsigned long, cmdline_len, const char __user *, cmdline_ptr,
unsigned long, flags)
@@ -1451,6 +1458,8 @@
return ret;
}
+#endif /* CONFIG_KEXEC_FILE */
+
void crash_kexec(struct pt_regs *regs)
{
/* Take the kexec_mutex here to prevent sys_kexec_load
@@ -2006,6 +2015,7 @@
subsys_initcall(crash_save_vmcoreinfo_init);
+#ifdef CONFIG_KEXEC_FILE
static int __kexec_add_segment(struct kimage *image, char *buf,
unsigned long bufsz, unsigned long mem,
unsigned long memsz)
@@ -2682,6 +2692,7 @@
return 0;
}
+#endif /* CONFIG_KEXEC_FILE */
/*
* Move into place and start executing a preloaded standalone
diff --git a/kernel/resource.c b/kernel/resource.c
index da14b8d..60c5a38 100644
--- a/kernel/resource.c
+++ b/kernel/resource.c
@@ -351,15 +351,12 @@
end = res->end;
BUG_ON(start >= end);
+ if (first_level_children_only)
+ sibling_only = true;
+
read_lock(&resource_lock);
- if (first_level_children_only) {
- p = iomem_resource.child;
- sibling_only = true;
- } else
- p = &iomem_resource;
-
- while ((p = next_resource(p, sibling_only))) {
+ for (p = iomem_resource.child; p; p = next_resource(p, sibling_only)) {
if (p->flags != res->flags)
continue;
if (name && strcmp(p->name, name))
diff --git a/kernel/trace/ring_buffer.c b/kernel/trace/ring_buffer.c
index afb04b9..b38fb2b 100644
--- a/kernel/trace/ring_buffer.c
+++ b/kernel/trace/ring_buffer.c
@@ -626,8 +626,22 @@
work = &cpu_buffer->irq_work;
}
- work->waiters_pending = true;
poll_wait(filp, &work->waiters, poll_table);
+ work->waiters_pending = true;
+ /*
+ * There's a tight race between setting the waiters_pending and
+ * checking if the ring buffer is empty. Once the waiters_pending bit
+ * is set, the next event will wake the task up, but we can get stuck
+ * if there's only a single event in.
+ *
+ * FIXME: Ideally, we need a memory barrier on the writer side as well,
+ * but adding a memory barrier to all events will cause too much of a
+ * performance hit in the fast path. We only need a memory barrier when
+ * the buffer goes from empty to having content. But as this race is
+ * extremely small, and it's not a problem if another event comes in, we
+ * will fix it later.
+ */
+ smp_mb();
if ((cpu == RING_BUFFER_ALL_CPUS && !ring_buffer_empty(buffer)) ||
(cpu != RING_BUFFER_ALL_CPUS && !ring_buffer_empty_cpu(buffer, cpu)))
diff --git a/lib/Kconfig.debug b/lib/Kconfig.debug
index 07c2832..a285900 100644
--- a/lib/Kconfig.debug
+++ b/lib/Kconfig.debug
@@ -892,6 +892,10 @@
the full mutex checks enabled with (CONFIG_PROVE_LOCKING) this
will test all possible w/w mutex interface abuse with the
exception of simply not acquiring all the required locks.
+ Note that this feature can introduce significant overhead, so
+ it really should not be enabled in a production or distro kernel,
+ even a debug kernel. If you are a driver writer, enable it. If
+ you are a distro, do not.
config DEBUG_LOCK_ALLOC
bool "Lock debugging: detect incorrect freeing of live locks"
@@ -1032,8 +1036,13 @@
either tracing or lock debugging.
config STACKTRACE
- bool
+ bool "Stack backtrace support"
depends on STACKTRACE_SUPPORT
+ help
+ This option causes the kernel to create a /proc/pid/stack for
+ every process, showing its current stack trace.
+ It is also used by various kernel debugging features that require
+ stack trace generation.
config DEBUG_KOBJECT
bool "kobject debugging"
diff --git a/mm/hugetlb_cgroup.c b/mm/hugetlb_cgroup.c
index 9eebfad..a67c26e 100644
--- a/mm/hugetlb_cgroup.c
+++ b/mm/hugetlb_cgroup.c
@@ -217,7 +217,7 @@
if (hugetlb_cgroup_disabled())
return;
- VM_BUG_ON(!spin_is_locked(&hugetlb_lock));
+ lockdep_assert_held(&hugetlb_lock);
h_cg = hugetlb_cgroup_from_page(page);
if (unlikely(!h_cg))
return;
diff --git a/mm/memblock.c b/mm/memblock.c
index 6d2f219..70fad0c 100644
--- a/mm/memblock.c
+++ b/mm/memblock.c
@@ -192,8 +192,7 @@
phys_addr_t align, phys_addr_t start,
phys_addr_t end, int nid)
{
- int ret;
- phys_addr_t kernel_end;
+ phys_addr_t kernel_end, ret;
/* pump up @end */
if (end == MEMBLOCK_ALLOC_ACCESSIBLE)
diff --git a/mm/memory.c b/mm/memory.c
index ab3537b..adeac30 100644
--- a/mm/memory.c
+++ b/mm/memory.c
@@ -751,7 +751,7 @@
unsigned long pfn = pte_pfn(pte);
if (HAVE_PTE_SPECIAL) {
- if (likely(!pte_special(pte) || pte_numa(pte)))
+ if (likely(!pte_special(pte)))
goto check_pfn;
if (vma->vm_flags & (VM_PFNMAP | VM_MIXEDMAP))
return NULL;
@@ -777,15 +777,14 @@
}
}
+ if (is_zero_pfn(pfn))
+ return NULL;
check_pfn:
if (unlikely(pfn > highest_memmap_pfn)) {
print_bad_pte(vma, addr, pte, NULL);
return NULL;
}
- if (is_zero_pfn(pfn))
- return NULL;
-
/*
* NOTE! We still have PageReserved() pages in the page tables.
* eg. VDSO mappings can cause them to exist.
diff --git a/mm/pgtable-generic.c b/mm/pgtable-generic.c
index a8b9199..dfb79e0 100644
--- a/mm/pgtable-generic.c
+++ b/mm/pgtable-generic.c
@@ -195,7 +195,7 @@
pmd_t entry = *pmdp;
if (pmd_numa(entry))
entry = pmd_mknonnuma(entry);
- set_pmd_at(vma->vm_mm, address, pmdp, pmd_mknotpresent(*pmdp));
+ set_pmd_at(vma->vm_mm, address, pmdp, pmd_mknotpresent(entry));
flush_tlb_range(vma, address, address + HPAGE_PMD_SIZE);
}
#endif /* CONFIG_TRANSPARENT_HUGEPAGE */
diff --git a/mm/zbud.c b/mm/zbud.c
index a05790b..f26e7fc 100644
--- a/mm/zbud.c
+++ b/mm/zbud.c
@@ -195,6 +195,7 @@
.total_size = zbud_zpool_total_size,
};
+MODULE_ALIAS("zpool-zbud");
#endif /* CONFIG_ZPOOL */
/*****************
diff --git a/mm/zpool.c b/mm/zpool.c
index e40612a..739cdf0 100644
--- a/mm/zpool.c
+++ b/mm/zpool.c
@@ -150,7 +150,7 @@
driver = zpool_get_driver(type);
if (!driver) {
- request_module(type);
+ request_module("zpool-%s", type);
driver = zpool_get_driver(type);
}
diff --git a/mm/zsmalloc.c b/mm/zsmalloc.c
index 4e2fc83..94f38fa 100644
--- a/mm/zsmalloc.c
+++ b/mm/zsmalloc.c
@@ -315,6 +315,7 @@
.total_size = zs_zpool_total_size,
};
+MODULE_ALIAS("zpool-zsmalloc");
#endif /* CONFIG_ZPOOL */
/* per-cpu VM mapping areas for zspage accesses that cross page boundaries */
diff --git a/scripts/checkpatch.pl b/scripts/checkpatch.pl
index 31a731e..b385bcb 100755
--- a/scripts/checkpatch.pl
+++ b/scripts/checkpatch.pl
@@ -2133,7 +2133,7 @@
# Check for improperly formed commit descriptions
if ($in_commit_log &&
$line =~ /\bcommit\s+[0-9a-f]{5,}/i &&
- $line !~ /\b[Cc]ommit [0-9a-f]{12,16} \("/) {
+ $line !~ /\b[Cc]ommit [0-9a-f]{12,40} \("/) {
$line =~ /\b(c)ommit\s+([0-9a-f]{5,})/i;
my $init_char = $1;
my $orig_commit = lc($2);
@@ -2141,7 +2141,7 @@
my $desc = 'commit description';
($id, $desc) = git_commit_info($orig_commit, $id, $desc);
ERROR("GIT_COMMIT_ID",
- "Please use 12 to 16 chars for the git commit ID like: '${init_char}ommit $id (\"$desc\")'\n" . $herecurr);
+ "Please use 12 or more chars for the git commit ID like: '${init_char}ommit $id (\"$desc\")'\n" . $herecurr);
}
# Check for added, moved or deleted files
diff --git a/scripts/kernel-doc b/scripts/kernel-doc
index 16a07cf..70bea94 100755
--- a/scripts/kernel-doc
+++ b/scripts/kernel-doc
@@ -2085,6 +2085,7 @@
$prototype =~ s/^noinline +//;
$prototype =~ s/__init +//;
$prototype =~ s/__init_or_module +//;
+ $prototype =~ s/__meminit +//;
$prototype =~ s/__must_check +//;
$prototype =~ s/__weak +//;
my $define = $prototype =~ s/^#\s*define\s+//; #ak added
diff --git a/security/tomoyo/realpath.c b/security/tomoyo/realpath.c
index a3386d1..bed745c 100644
--- a/security/tomoyo/realpath.c
+++ b/security/tomoyo/realpath.c
@@ -173,7 +173,7 @@
* Use filesystem name if filesystem does not support rename()
* operation.
*/
- if (!inode->i_op->rename)
+ if (!inode->i_op->rename && !inode->i_op->rename2)
goto prepend_filesystem_name;
}
/* Prepend device name. */
@@ -282,7 +282,8 @@
* Get local name for filesystems without rename() operation
* or dentry without vfsmount.
*/
- if (!path->mnt || !inode->i_op->rename)
+ if (!path->mnt ||
+ (!inode->i_op->rename && !inode->i_op->rename2))
pos = tomoyo_get_local_path(path->dentry, buf,
buf_len - 1);
/* Get absolute name for the rest. */
diff --git a/sound/core/info.c b/sound/core/info.c
index 051d55b..9f404e9 100644
--- a/sound/core/info.c
+++ b/sound/core/info.c
@@ -684,7 +684,7 @@
* snd_info_get_line - read one line from the procfs buffer
* @buffer: the procfs buffer
* @line: the buffer to store
- * @len: the max. buffer size - 1
+ * @len: the max. buffer size
*
* Reads one line from the buffer and stores the string.
*
@@ -704,7 +704,7 @@
buffer->stop = 1;
if (c == '\n')
break;
- if (len) {
+ if (len > 1) {
len--;
*line++ = c;
}
diff --git a/sound/core/pcm_misc.c b/sound/core/pcm_misc.c
index 4560ca0..2c6fd80 100644
--- a/sound/core/pcm_misc.c
+++ b/sound/core/pcm_misc.c
@@ -142,11 +142,11 @@
},
[SNDRV_PCM_FORMAT_DSD_U8] = {
.width = 8, .phys = 8, .le = 1, .signd = 0,
- .silence = {},
+ .silence = { 0x69 },
},
[SNDRV_PCM_FORMAT_DSD_U16_LE] = {
.width = 16, .phys = 16, .le = 1, .signd = 0,
- .silence = {},
+ .silence = { 0x69, 0x69 },
},
/* FIXME: the following three formats are not defined properly yet */
[SNDRV_PCM_FORMAT_MPEG] = {
diff --git a/sound/pci/ctxfi/ct20k1reg.h b/sound/pci/ctxfi/ct20k1reg.h
index f2e34e3..5851249 100644
--- a/sound/pci/ctxfi/ct20k1reg.h
+++ b/sound/pci/ctxfi/ct20k1reg.h
@@ -7,7 +7,7 @@
*/
#ifndef CT20K1REG_H
-#define CT20k1REG_H
+#define CT20K1REG_H
/* 20k1 registers */
#define DSPXRAM_START 0x000000
@@ -632,5 +632,3 @@
#define I2SD_R 0x19L
#endif /* CT20K1REG_H */
-
-
diff --git a/sound/pci/hda/ca0132_regs.h b/sound/pci/hda/ca0132_regs.h
index 07e7609..8371274 100644
--- a/sound/pci/hda/ca0132_regs.h
+++ b/sound/pci/hda/ca0132_regs.h
@@ -20,7 +20,7 @@
*/
#ifndef __CA0132_REGS_H
-#define __CA0312_REGS_H
+#define __CA0132_REGS_H
#define DSP_CHIP_OFFSET 0x100000
#define DSP_DBGCNTL_MODULE_OFFSET 0xE30
diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index d71270a..d446ac3 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -4408,6 +4408,7 @@
ALC292_FIXUP_TPT440_DOCK,
ALC283_FIXUP_BXBT2807_MIC,
ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED,
+ ALC282_FIXUP_ASPIRE_V5_PINS,
};
static const struct hda_fixup alc269_fixups[] = {
@@ -4855,6 +4856,22 @@
.chained_before = true,
.chain_id = ALC255_FIXUP_DELL1_MIC_NO_PRESENCE
},
+ [ALC282_FIXUP_ASPIRE_V5_PINS] = {
+ .type = HDA_FIXUP_PINS,
+ .v.pins = (const struct hda_pintbl[]) {
+ { 0x12, 0x90a60130 },
+ { 0x14, 0x90170110 },
+ { 0x17, 0x40000008 },
+ { 0x18, 0x411111f0 },
+ { 0x19, 0x411111f0 },
+ { 0x1a, 0x411111f0 },
+ { 0x1b, 0x411111f0 },
+ { 0x1d, 0x40f89b2d },
+ { 0x1e, 0x411111f0 },
+ { 0x21, 0x0321101f },
+ { },
+ },
+ },
};
@@ -4866,6 +4883,7 @@
SND_PCI_QUIRK(0x1025, 0x0740, "Acer AO725", ALC271_FIXUP_HP_GATE_MIC_JACK),
SND_PCI_QUIRK(0x1025, 0x0742, "Acer AO756", ALC271_FIXUP_HP_GATE_MIC_JACK),
SND_PCI_QUIRK(0x1025, 0x0775, "Acer Aspire E1-572", ALC271_FIXUP_HP_GATE_MIC_JACK_E1_572),
+ SND_PCI_QUIRK(0x1025, 0x079b, "Acer Aspire V5-573G", ALC282_FIXUP_ASPIRE_V5_PINS),
SND_PCI_QUIRK(0x1028, 0x0470, "Dell M101z", ALC269_FIXUP_DELL_M101Z),
SND_PCI_QUIRK(0x1028, 0x05bd, "Dell", ALC269_FIXUP_DELL2_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x05be, "Dell", ALC269_FIXUP_DELL2_MIC_NO_PRESENCE),
diff --git a/tools/testing/selftests/ipc/Makefile b/tools/testing/selftests/ipc/Makefile
index 5386fd7..74bbefd 100644
--- a/tools/testing/selftests/ipc/Makefile
+++ b/tools/testing/selftests/ipc/Makefile
@@ -1,18 +1,18 @@
uname_M := $(shell uname -m 2>/dev/null || echo not)
ARCH ?= $(shell echo $(uname_M) | sed -e s/i.86/i386/)
ifeq ($(ARCH),i386)
- ARCH := X86
+ ARCH := x86
CFLAGS := -DCONFIG_X86_32 -D__i386__
endif
ifeq ($(ARCH),x86_64)
- ARCH := X86
+ ARCH := x86
CFLAGS := -DCONFIG_X86_64 -D__x86_64__
endif
CFLAGS += -I../../../../usr/include/
all:
-ifeq ($(ARCH),X86)
+ifeq ($(ARCH),x86)
gcc $(CFLAGS) msgque.c -o msgque_test
else
echo "Not an x86 target, can't build msgque selftest"
diff --git a/tools/testing/selftests/kcmp/Makefile b/tools/testing/selftests/kcmp/Makefile
index d7d6bbe..8aabd82 100644
--- a/tools/testing/selftests/kcmp/Makefile
+++ b/tools/testing/selftests/kcmp/Makefile
@@ -1,11 +1,11 @@
uname_M := $(shell uname -m 2>/dev/null || echo not)
ARCH ?= $(shell echo $(uname_M) | sed -e s/i.86/i386/)
ifeq ($(ARCH),i386)
- ARCH := X86
+ ARCH := x86
CFLAGS := -DCONFIG_X86_32 -D__i386__
endif
ifeq ($(ARCH),x86_64)
- ARCH := X86
+ ARCH := x86
CFLAGS := -DCONFIG_X86_64 -D__x86_64__
endif
@@ -15,7 +15,7 @@
CFLAGS += -I../../../../arch/x86/include/
all:
-ifeq ($(ARCH),X86)
+ifeq ($(ARCH),x86)
gcc $(CFLAGS) kcmp_test.c -o kcmp_test
else
echo "Not an x86 target, can't build kcmp selftest"
diff --git a/tools/testing/selftests/memfd/Makefile b/tools/testing/selftests/memfd/Makefile
index 6816c49..ad4ab01 100644
--- a/tools/testing/selftests/memfd/Makefile
+++ b/tools/testing/selftests/memfd/Makefile
@@ -1,10 +1,10 @@
uname_M := $(shell uname -m 2>/dev/null || echo not)
ARCH ?= $(shell echo $(uname_M) | sed -e s/i.86/i386/)
ifeq ($(ARCH),i386)
- ARCH := X86
+ ARCH := x86
endif
ifeq ($(ARCH),x86_64)
- ARCH := X86
+ ARCH := x86
endif
CFLAGS += -D_FILE_OFFSET_BITS=64
@@ -14,20 +14,20 @@
CFLAGS += -I../../../../include/
all:
-ifeq ($(ARCH),X86)
+ifeq ($(ARCH),x86)
gcc $(CFLAGS) memfd_test.c -o memfd_test
else
echo "Not an x86 target, can't build memfd selftest"
endif
run_tests: all
-ifeq ($(ARCH),X86)
+ifeq ($(ARCH),x86)
gcc $(CFLAGS) memfd_test.c -o memfd_test
endif
@./memfd_test || echo "memfd_test: [FAIL]"
build_fuse:
-ifeq ($(ARCH),X86)
+ifeq ($(ARCH),x86)
gcc $(CFLAGS) fuse_mnt.c `pkg-config fuse --cflags --libs` -o fuse_mnt
gcc $(CFLAGS) fuse_test.c -o fuse_test
else
diff --git a/drivers/staging/usbip/userspace/.gitignore b/tools/usb/usbip/.gitignore
similarity index 100%
rename from drivers/staging/usbip/userspace/.gitignore
rename to tools/usb/usbip/.gitignore
diff --git a/drivers/staging/usbip/userspace/AUTHORS b/tools/usb/usbip/AUTHORS
similarity index 100%
rename from drivers/staging/usbip/userspace/AUTHORS
rename to tools/usb/usbip/AUTHORS
diff --git a/drivers/staging/usbip/userspace/COPYING b/tools/usb/usbip/COPYING
similarity index 100%
rename from drivers/staging/usbip/userspace/COPYING
rename to tools/usb/usbip/COPYING
diff --git a/drivers/staging/usbip/userspace/INSTALL b/tools/usb/usbip/INSTALL
similarity index 100%
rename from drivers/staging/usbip/userspace/INSTALL
rename to tools/usb/usbip/INSTALL
diff --git a/drivers/staging/usbip/userspace/Makefile.am b/tools/usb/usbip/Makefile.am
similarity index 100%
rename from drivers/staging/usbip/userspace/Makefile.am
rename to tools/usb/usbip/Makefile.am
diff --git a/drivers/staging/usbip/userspace/README b/tools/usb/usbip/README
similarity index 100%
rename from drivers/staging/usbip/userspace/README
rename to tools/usb/usbip/README
diff --git a/drivers/staging/usbip/userspace/autogen.sh b/tools/usb/usbip/autogen.sh
similarity index 100%
rename from drivers/staging/usbip/userspace/autogen.sh
rename to tools/usb/usbip/autogen.sh
diff --git a/drivers/staging/usbip/userspace/cleanup.sh b/tools/usb/usbip/cleanup.sh
similarity index 100%
rename from drivers/staging/usbip/userspace/cleanup.sh
rename to tools/usb/usbip/cleanup.sh
diff --git a/drivers/staging/usbip/userspace/configure.ac b/tools/usb/usbip/configure.ac
similarity index 100%
rename from drivers/staging/usbip/userspace/configure.ac
rename to tools/usb/usbip/configure.ac
diff --git a/drivers/staging/usbip/userspace/doc/usbip.8 b/tools/usb/usbip/doc/usbip.8
similarity index 100%
rename from drivers/staging/usbip/userspace/doc/usbip.8
rename to tools/usb/usbip/doc/usbip.8
diff --git a/drivers/staging/usbip/userspace/doc/usbipd.8 b/tools/usb/usbip/doc/usbipd.8
similarity index 100%
rename from drivers/staging/usbip/userspace/doc/usbipd.8
rename to tools/usb/usbip/doc/usbipd.8
diff --git a/drivers/staging/usbip/userspace/libsrc/Makefile.am b/tools/usb/usbip/libsrc/Makefile.am
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/Makefile.am
rename to tools/usb/usbip/libsrc/Makefile.am
diff --git a/drivers/staging/usbip/userspace/libsrc/list.h b/tools/usb/usbip/libsrc/list.h
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/list.h
rename to tools/usb/usbip/libsrc/list.h
diff --git a/drivers/staging/usbip/userspace/libsrc/names.c b/tools/usb/usbip/libsrc/names.c
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/names.c
rename to tools/usb/usbip/libsrc/names.c
diff --git a/drivers/staging/usbip/userspace/libsrc/names.h b/tools/usb/usbip/libsrc/names.h
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/names.h
rename to tools/usb/usbip/libsrc/names.h
diff --git a/drivers/staging/usbip/userspace/libsrc/sysfs_utils.c b/tools/usb/usbip/libsrc/sysfs_utils.c
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/sysfs_utils.c
rename to tools/usb/usbip/libsrc/sysfs_utils.c
diff --git a/drivers/staging/usbip/userspace/libsrc/sysfs_utils.h b/tools/usb/usbip/libsrc/sysfs_utils.h
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/sysfs_utils.h
rename to tools/usb/usbip/libsrc/sysfs_utils.h
diff --git a/drivers/staging/usbip/userspace/libsrc/usbip_common.c b/tools/usb/usbip/libsrc/usbip_common.c
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/usbip_common.c
rename to tools/usb/usbip/libsrc/usbip_common.c
diff --git a/drivers/staging/usbip/userspace/libsrc/usbip_common.h b/tools/usb/usbip/libsrc/usbip_common.h
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/usbip_common.h
rename to tools/usb/usbip/libsrc/usbip_common.h
diff --git a/drivers/staging/usbip/userspace/libsrc/usbip_host_driver.c b/tools/usb/usbip/libsrc/usbip_host_driver.c
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/usbip_host_driver.c
rename to tools/usb/usbip/libsrc/usbip_host_driver.c
diff --git a/drivers/staging/usbip/userspace/libsrc/usbip_host_driver.h b/tools/usb/usbip/libsrc/usbip_host_driver.h
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/usbip_host_driver.h
rename to tools/usb/usbip/libsrc/usbip_host_driver.h
diff --git a/drivers/staging/usbip/userspace/libsrc/vhci_driver.c b/tools/usb/usbip/libsrc/vhci_driver.c
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/vhci_driver.c
rename to tools/usb/usbip/libsrc/vhci_driver.c
diff --git a/drivers/staging/usbip/userspace/libsrc/vhci_driver.h b/tools/usb/usbip/libsrc/vhci_driver.h
similarity index 100%
rename from drivers/staging/usbip/userspace/libsrc/vhci_driver.h
rename to tools/usb/usbip/libsrc/vhci_driver.h
diff --git a/drivers/staging/usbip/userspace/src/Makefile.am b/tools/usb/usbip/src/Makefile.am
similarity index 100%
rename from drivers/staging/usbip/userspace/src/Makefile.am
rename to tools/usb/usbip/src/Makefile.am
diff --git a/drivers/staging/usbip/userspace/src/usbip.c b/tools/usb/usbip/src/usbip.c
similarity index 100%
rename from drivers/staging/usbip/userspace/src/usbip.c
rename to tools/usb/usbip/src/usbip.c
diff --git a/drivers/staging/usbip/userspace/src/usbip.h b/tools/usb/usbip/src/usbip.h
similarity index 100%
rename from drivers/staging/usbip/userspace/src/usbip.h
rename to tools/usb/usbip/src/usbip.h
diff --git a/drivers/staging/usbip/userspace/src/usbip_attach.c b/tools/usb/usbip/src/usbip_attach.c
similarity index 100%
rename from drivers/staging/usbip/userspace/src/usbip_attach.c
rename to tools/usb/usbip/src/usbip_attach.c
diff --git a/drivers/staging/usbip/userspace/src/usbip_bind.c b/tools/usb/usbip/src/usbip_bind.c
similarity index 100%
rename from drivers/staging/usbip/userspace/src/usbip_bind.c
rename to tools/usb/usbip/src/usbip_bind.c
diff --git a/drivers/staging/usbip/userspace/src/usbip_detach.c b/tools/usb/usbip/src/usbip_detach.c
similarity index 100%
rename from drivers/staging/usbip/userspace/src/usbip_detach.c
rename to tools/usb/usbip/src/usbip_detach.c
diff --git a/drivers/staging/usbip/userspace/src/usbip_list.c b/tools/usb/usbip/src/usbip_list.c
similarity index 100%
rename from drivers/staging/usbip/userspace/src/usbip_list.c
rename to tools/usb/usbip/src/usbip_list.c
diff --git a/drivers/staging/usbip/userspace/src/usbip_network.c b/tools/usb/usbip/src/usbip_network.c
similarity index 100%
rename from drivers/staging/usbip/userspace/src/usbip_network.c
rename to tools/usb/usbip/src/usbip_network.c
diff --git a/drivers/staging/usbip/userspace/src/usbip_network.h b/tools/usb/usbip/src/usbip_network.h
similarity index 100%
rename from drivers/staging/usbip/userspace/src/usbip_network.h
rename to tools/usb/usbip/src/usbip_network.h
diff --git a/drivers/staging/usbip/userspace/src/usbip_port.c b/tools/usb/usbip/src/usbip_port.c
similarity index 100%
rename from drivers/staging/usbip/userspace/src/usbip_port.c
rename to tools/usb/usbip/src/usbip_port.c
diff --git a/drivers/staging/usbip/userspace/src/usbip_unbind.c b/tools/usb/usbip/src/usbip_unbind.c
similarity index 100%
rename from drivers/staging/usbip/userspace/src/usbip_unbind.c
rename to tools/usb/usbip/src/usbip_unbind.c
diff --git a/drivers/staging/usbip/userspace/src/usbipd.c b/tools/usb/usbip/src/usbipd.c
similarity index 100%
rename from drivers/staging/usbip/userspace/src/usbipd.c
rename to tools/usb/usbip/src/usbipd.c
diff --git a/drivers/staging/usbip/userspace/src/utils.c b/tools/usb/usbip/src/utils.c
similarity index 100%
rename from drivers/staging/usbip/userspace/src/utils.c
rename to tools/usb/usbip/src/utils.c
diff --git a/drivers/staging/usbip/userspace/src/utils.h b/tools/usb/usbip/src/utils.h
similarity index 100%
rename from drivers/staging/usbip/userspace/src/utils.h
rename to tools/usb/usbip/src/utils.h