net: phy: Add MAC-IF driver for Microsemi PHYs.
All the review comments updated and resending for review.
This is MAC interface feature.
Microsemi PHY can support RGMII, RMII or GMII/MII interface between MAC and PHY.
MAC-IF function program the right value based on Device tree configuration.
Tested on Beaglebone Black with VSC 8531 PHY.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/phy/mscc.c b/drivers/net/phy/mscc.c
index c09cc4a..d350deb 100644
--- a/drivers/net/phy/mscc.c
+++ b/drivers/net/phy/mscc.c
@@ -23,6 +23,16 @@
RGMII_RX_CLK_DELAY_3_4_NS = 7
};
+/* Microsemi VSC85xx PHY registers */
+/* IEEE 802. Std Registers */
+#define MSCC_PHY_EXT_PHY_CNTL_1 23
+#define MAC_IF_SELECTION_MASK 0x1800
+#define MAC_IF_SELECTION_GMII 0
+#define MAC_IF_SELECTION_RMII 1
+#define MAC_IF_SELECTION_RGMII 2
+#define MAC_IF_SELECTION_POS 11
+#define FAR_END_LOOPBACK_MODE_MASK 0x0008
+
#define MII_VSC85XX_INT_MASK 25
#define MII_VSC85XX_INT_MASK_MASK 0xa000
#define MII_VSC85XX_INT_STATUS 26
@@ -48,6 +58,42 @@
return rc;
}
+static int vsc85xx_mac_if_set(struct phy_device *phydev,
+ phy_interface_t interface)
+{
+ int rc;
+ u16 reg_val;
+
+ mutex_lock(&phydev->lock);
+ reg_val = phy_read(phydev, MSCC_PHY_EXT_PHY_CNTL_1);
+ reg_val &= ~(MAC_IF_SELECTION_MASK);
+ switch (interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ reg_val |= (MAC_IF_SELECTION_RGMII << MAC_IF_SELECTION_POS);
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ reg_val |= (MAC_IF_SELECTION_RMII << MAC_IF_SELECTION_POS);
+ break;
+ case PHY_INTERFACE_MODE_MII:
+ case PHY_INTERFACE_MODE_GMII:
+ reg_val |= (MAC_IF_SELECTION_GMII << MAC_IF_SELECTION_POS);
+ break;
+ default:
+ rc = -EINVAL;
+ goto out_unlock;
+ }
+ rc = phy_write(phydev, MSCC_PHY_EXT_PHY_CNTL_1, reg_val);
+ if (rc != 0)
+ goto out_unlock;
+
+ rc = genphy_soft_reset(phydev);
+
+out_unlock:
+ mutex_unlock(&phydev->lock);
+
+ return rc;
+}
+
static int vsc85xx_default_config(struct phy_device *phydev)
{
int rc;
@@ -77,6 +123,11 @@
rc = vsc85xx_default_config(phydev);
if (rc)
return rc;
+
+ rc = vsc85xx_mac_if_set(phydev, phydev->interface);
+ if (rc)
+ return rc;
+
rc = genphy_config_init(phydev);
return rc;