drm/i915: Fix DVO 2x clock enable on 830M
The spec says:
"For the correct operation of the muxed DVO pins (GDEVSELB/ I2Cdata,
GIRDBY/I2CClk) and (GFRAMEB/DVI_Data, GTRDYB/DVI_Clk): Bit 31
(DPLL VCO Enable) and Bit 30 (2X Clock Enable) must be set to “1” in
both the DPLL A Control Register (06014h-06017h) and DPLL B Control
Register (06018h-0601Bh)."
The pipe A and B force quirks take care of DPLL_VCO_ENABLE, so we
just need a bit of special care to handle DPLL_DVO_2X_MODE.
v2: Recompute num_dvo_pipes on the spot, use PIPE_A/PIPE_B instead
of pipe/!pipe for the register offsets in disable (Daniel)
Add a comment about the ordering in enable and another one
about filtering out the DVO 2x bit in state readout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Thomas Richter <richter@rus.uni-stuttgart.de> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 1386086..f4b8cb3 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -1612,6 +1612,18 @@
mutex_unlock(&dev_priv->dpio_lock);
}
+static int intel_num_dvo_pipes(struct drm_device *dev)
+{
+ struct intel_crtc *crtc;
+ int count = 0;
+
+ for_each_intel_crtc(dev, crtc)
+ count += crtc->active &&
+ intel_pipe_has_type(&crtc->base, INTEL_OUTPUT_DVO);
+
+ return count;
+}
+
static void i9xx_enable_pll(struct intel_crtc *crtc)
{
struct drm_device *dev = crtc->base.dev;
@@ -1628,7 +1640,18 @@
if (IS_MOBILE(dev) && !IS_I830(dev))
assert_panel_unlocked(dev_priv, crtc->pipe);
- I915_WRITE(reg, dpll);
+ /* Enable DVO 2x clock on both PLLs if necessary */
+ if (IS_I830(dev) && intel_num_dvo_pipes(dev) > 0) {
+ /*
+ * It appears to be important that we don't enable this
+ * for the current pipe before otherwise configuring the
+ * PLL. No idea how this should be handled if multiple
+ * DVO outputs are enabled simultaneosly.
+ */
+ dpll |= DPLL_DVO_2X_MODE;
+ I915_WRITE(DPLL(!crtc->pipe),
+ I915_READ(DPLL(!crtc->pipe)) | DPLL_DVO_2X_MODE);
+ }
/* Wait for the clocks to stabilize. */
POSTING_READ(reg);
@@ -1667,8 +1690,22 @@
*
* Note! This is for pre-ILK only.
*/
-static void i9xx_disable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)
+static void i9xx_disable_pll(struct intel_crtc *crtc)
{
+ struct drm_device *dev = crtc->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ enum pipe pipe = crtc->pipe;
+
+ /* Disable DVO 2x clock on both PLLs if necessary */
+ if (IS_I830(dev) &&
+ intel_pipe_has_type(&crtc->base, INTEL_OUTPUT_DVO) &&
+ intel_num_dvo_pipes(dev) == 1) {
+ I915_WRITE(DPLL(PIPE_B),
+ I915_READ(DPLL(PIPE_B)) & ~DPLL_DVO_2X_MODE);
+ I915_WRITE(DPLL(PIPE_A),
+ I915_READ(DPLL(PIPE_A)) & ~DPLL_DVO_2X_MODE);
+ }
+
/* Don't disable pipe or pipe PLLs if needed */
if ((pipe == PIPE_A && dev_priv->quirks & QUIRK_PIPEA_FORCE) ||
(pipe == PIPE_B && dev_priv->quirks & QUIRK_PIPEB_FORCE))
@@ -4941,7 +4978,7 @@
else if (IS_VALLEYVIEW(dev))
vlv_disable_pll(dev_priv, pipe);
else
- i9xx_disable_pll(dev_priv, pipe);
+ i9xx_disable_pll(intel_crtc);
}
if (!IS_GEN2(dev))
@@ -5945,7 +5982,7 @@
dpll |= PLL_P2_DIVIDE_BY_4;
}
- if (intel_pipe_has_type(&crtc->base, INTEL_OUTPUT_DVO))
+ if (!IS_I830(dev) && intel_pipe_has_type(&crtc->base, INTEL_OUTPUT_DVO))
dpll |= DPLL_DVO_2X_MODE;
if (intel_pipe_has_type(&crtc->base, INTEL_OUTPUT_LVDS) &&
@@ -6451,6 +6488,14 @@
}
pipe_config->dpll_hw_state.dpll = I915_READ(DPLL(crtc->pipe));
if (!IS_VALLEYVIEW(dev)) {
+ /*
+ * DPLL_DVO_2X_MODE must be enabled for both DPLLs
+ * on 830. Filter it out here so that we don't
+ * report errors due to that.
+ */
+ if (IS_I830(dev))
+ pipe_config->dpll_hw_state.dpll &= ~DPLL_DVO_2X_MODE;
+
pipe_config->dpll_hw_state.fp0 = I915_READ(FP0(crtc->pipe));
pipe_config->dpll_hw_state.fp1 = I915_READ(FP1(crtc->pipe));
} else {