Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (63 commits)
ide: remove REQ_TYPE_ATA_CMD
ide: switch ide_cmd_ioctl() to use REQ_TYPE_ATA_TASKFILE requests
ide: switch set_xfer_rate() to use REQ_TYPE_ATA_TASKFILE requests
ide: fix final status check in drive_cmd_intr()
ide: check BUSY and ERROR status bits before reading data in drive_cmd_intr()
ide: don't enable local IRQs for PIO-in in driver_cmd_intr() (take 2)
ide: convert "empty" REQ_TYPE_ATA_CMD requests to use REQ_TYPE_ATA_TASKFILE
ide: initialize rq->cmd_type in ide_init_drive_cmd() callers
ide: use wait_drive_not_busy() in drive_cmd_intr() (take 2)
ide: kill DATA_READY define
ide: task_end_request() fix
ide: use rq->nr_sectors in task_end_request()
ide: remove needless ->cursg clearing from task_end_request()
ide: set IDE_TFLAG_IN_* flags before queuing/executing command
ide-tape: fix handling of non-special requests in ->end_request method
ide: fix final status check in task_in_intr()
ide: clear HOB bit for REQ_TYPE_ATA_CMD requests in ide_end_drive_cmd()
ide: fix ->io_32bit race in ide_taskfile_ioctl()
cmd64x: remove /proc/ide/cmd64x
ide: remove broken disk byte-swapping support
...
diff --git a/Documentation/ide.txt b/Documentation/ide.txt
index 1d50f23..94e2e3b 100644
--- a/Documentation/ide.txt
+++ b/Documentation/ide.txt
@@ -30,7 +30,7 @@
***
*** The CMD640 is also used on some Vesa Local Bus (VLB) cards, and is *NOT*
*** automatically detected by Linux. For safe, reliable operation with such
-*** interfaces, one *MUST* use the "ide0=cmd640_vlb" kernel option.
+*** interfaces, one *MUST* use the "cmd640.probe_vlb" kernel option.
***
*** Use of the "serialize" option is no longer necessary.
@@ -244,10 +244,6 @@
"hdx=nodma" : disallow DMA
- "hdx=swapdata" : when the drive is a disk, byte swap all data
-
- "hdx=bswap" : same as above..........
-
"hdx=scsi" : the return of the ide-scsi flag, this is useful for
allowing ide-floppy, ide-tape, and ide-cdrom|writers
to use ide-scsi emulation on a device specific option.
@@ -292,9 +288,6 @@
to the first ATA interface found on the particular host, and the defaults for
the base,ctl ports must not be altered.
- "ide0=cmd640_vlb" : *REQUIRED* for VLB cards with the CMD640 chip
- (not for PCI -- automatically detected)
-
"ide=doubler" : probe/support IDE doublers on Amiga
There may be more options than shown -- use the source, Luke!
@@ -310,6 +303,10 @@
* "probe" module parameter when ali14xx driver is compiled as module
("modprobe ali14xx probe")
+Also for legacy CMD640 host driver (cmd640) you need to use "probe_vlb"
+kernel paremeter to enable probing for VLB version of the chipset (PCI ones
+are detected automatically).
+
================================================================================
IDE ATAPI streaming tape driver
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index ee01e27..64df55e 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -325,7 +325,7 @@
If unsure, say N.
config BLK_DEV_CMD640
- bool "CMD640 chipset bugfix/support"
+ tristate "CMD640 chipset bugfix/support"
depends on X86
---help---
The CMD-Technologies CMD640 IDE chip is used on many common 486 and
@@ -359,9 +359,8 @@
Otherwise say N.
config BLK_DEV_IDEPNP
- bool "PNP EIDE support"
+ tristate "PNP EIDE support"
depends on PNP
- select IDE_GENERIC
help
If you have a PnP (Plug and Play) compatible EIDE card and
would like the kernel to automatically detect and activate
@@ -375,7 +374,19 @@
bool
config IDEPCI_PCIBUS_ORDER
- def_bool BLK_DEV_IDE=y && BLK_DEV_IDEPCI
+ bool "Probe IDE PCI devices in the PCI bus order (DEPRECATED)"
+ depends on BLK_DEV_IDE=y && BLK_DEV_IDEPCI
+ default y
+ help
+ Probe IDE PCI devices in the order in which they appear on the
+ PCI bus (i.e. 00:1f.1 PCI device before 02:01.0 PCI device)
+ instead of the order in which IDE PCI host drivers are loaded.
+
+ Please note that this method of assuring stable naming of
+ IDE devices is unreliable and use other means for achieving
+ it (i.e. udev).
+
+ If in doubt, say N.
# TODO: split it on per host driver config options (or module parameters)
config BLK_DEV_OFFBOARD
@@ -789,7 +800,7 @@
endif
config BLK_DEV_IDE_PMAC
- bool "Builtin PowerMac IDE support"
+ tristate "Builtin PowerMac IDE support"
depends on PPC_PMAC && IDE=y && BLK_DEV_IDE=y
help
This driver provides support for the built-in IDE controller on
@@ -843,8 +854,9 @@
depends on BLK_DEV_IDE_AU1XXX
config IDE_ARM
- def_bool ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
- select IDE_GENERIC
+ tristate "ARM IDE support"
+ depends on ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
+ default y
config BLK_DEV_IDE_ICSIDE
tristate "ICS IDE interface support"
@@ -876,10 +888,9 @@
Simtec BAST or the Thorcom VR1000
config ETRAX_IDE
- bool "ETRAX IDE support"
+ tristate "ETRAX IDE support"
depends on CRIS && BROKEN
select BLK_DEV_IDEDMA
- select IDE_GENERIC
help
Enables the ETRAX IDE driver.
@@ -911,17 +922,15 @@
endchoice
config IDE_H8300
- bool "H8300 IDE support"
+ tristate "H8300 IDE support"
depends on H8300
- select IDE_GENERIC
default y
help
Enables the H8300 IDE driver.
config BLK_DEV_GAYLE
- bool "Amiga Gayle IDE interface support"
+ tristate "Amiga Gayle IDE interface support"
depends on AMIGA
- select IDE_GENERIC
help
This is the IDE driver for the Amiga Gayle IDE interface. It supports
both the `A1200 style' and `A4000 style' of the Gayle IDE interface,
@@ -951,9 +960,8 @@
runtime using the "ide=doubler" kernel boot parameter.
config BLK_DEV_BUDDHA
- bool "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
+ tristate "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
depends on ZORRO && EXPERIMENTAL
- select IDE_GENERIC
help
This is the IDE driver for the IDE interfaces on the Buddha,
Catweasel and X-Surf expansion boards. It supports up to two interfaces
@@ -964,9 +972,8 @@
to one of its IDE interfaces.
config BLK_DEV_FALCON_IDE
- bool "Falcon IDE interface support"
+ tristate "Falcon IDE interface support"
depends on ATARI
- select IDE_GENERIC
help
This is the IDE driver for the builtin IDE interface on the Atari
Falcon. Say Y if you have a Falcon and want to use IDE devices (hard
@@ -974,9 +981,8 @@
interface.
config BLK_DEV_MAC_IDE
- bool "Macintosh Quadra/Powerbook IDE interface support"
+ tristate "Macintosh Quadra/Powerbook IDE interface support"
depends on MAC
- select IDE_GENERIC
help
This is the IDE driver for the builtin IDE interface on some m68k
Macintosh models. It supports both the `Quadra style' (used in
@@ -988,18 +994,16 @@
builtin IDE interface.
config BLK_DEV_Q40IDE
- bool "Q40/Q60 IDE interface support"
+ tristate "Q40/Q60 IDE interface support"
depends on Q40
- select IDE_GENERIC
help
Enable the on-board IDE controller in the Q40/Q60. This should
normally be on; disable it only if you are running a custom hard
drive subsystem through an expansion card.
config BLK_DEV_MPC8xx_IDE
- bool "MPC8xx IDE support"
+ tristate "MPC8xx IDE support"
depends on 8xx && (LWMON || IVMS8 || IVML24 || TQM8xxL) && IDE=y && BLK_DEV_IDE=y && !PPC_MERGE
- select IDE_GENERIC
help
This option provides support for IDE on Motorola MPC8xx Systems.
Please see 'Type of MPC8xx IDE interface' for details.
diff --git a/drivers/ide/Makefile b/drivers/ide/Makefile
index b181fc6..0d2da89 100644
--- a/drivers/ide/Makefile
+++ b/drivers/ide/Makefile
@@ -7,41 +7,37 @@
# Note : at this point, these files are compiled on all systems.
# In the future, some of these should be built conditionally.
#
-# First come modules that register themselves with the core
+# link order is important here
EXTRA_CFLAGS += -Idrivers/ide
-obj-$(CONFIG_BLK_DEV_IDE) += pci/
-
ide-core-y += ide.o ide-io.o ide-iops.o ide-lib.o ide-probe.o ide-taskfile.o
-ide-core-$(CONFIG_BLK_DEV_CMD640) += pci/cmd640.o
-
-# Core IDE code - must come before legacy
+# core IDE code
ide-core-$(CONFIG_BLK_DEV_IDEPCI) += setup-pci.o
ide-core-$(CONFIG_BLK_DEV_IDEDMA) += ide-dma.o
ide-core-$(CONFIG_IDE_PROC_FS) += ide-proc.o
-ide-core-$(CONFIG_BLK_DEV_IDEPNP) += ide-pnp.o
ide-core-$(CONFIG_BLK_DEV_IDEACPI) += ide-acpi.o
-# built-in only drivers from arm/
-ide-core-$(CONFIG_IDE_ARM) += arm/ide_arm.o
-
-# built-in only drivers from legacy/
-ide-core-$(CONFIG_BLK_DEV_BUDDHA) += legacy/buddha.o
-ide-core-$(CONFIG_BLK_DEV_FALCON_IDE) += legacy/falconide.o
-ide-core-$(CONFIG_BLK_DEV_GAYLE) += legacy/gayle.o
-ide-core-$(CONFIG_BLK_DEV_MAC_IDE) += legacy/macide.o
-ide-core-$(CONFIG_BLK_DEV_Q40IDE) += legacy/q40ide.o
-
-# built-in only drivers from ppc/
-ide-core-$(CONFIG_BLK_DEV_MPC8xx_IDE) += ppc/mpc8xx.o
-ide-core-$(CONFIG_BLK_DEV_IDE_PMAC) += ppc/pmac.o
-
-# built-in only drivers from h8300/
-ide-core-$(CONFIG_IDE_H8300) += h8300/ide-h8300.o
-
obj-$(CONFIG_BLK_DEV_IDE) += ide-core.o
+
+ifeq ($(CONFIG_IDE_ARM), y)
+ ide-arm-core-y += arm/ide_arm.o
+ obj-y += ide-arm-core.o
+endif
+
+obj-$(CONFIG_BLK_DEV_IDE) += legacy/ pci/
+
+obj-$(CONFIG_IDEPCI_PCIBUS_ORDER) += ide-scan-pci.o
+
+ifeq ($(CONFIG_BLK_DEV_CMD640), y)
+ cmd640-core-y += pci/cmd640.o
+ obj-y += cmd640-core.o
+endif
+
+obj-$(CONFIG_BLK_DEV_IDE) += cris/ ppc/
+obj-$(CONFIG_BLK_DEV_IDEPNP) += ide-pnp.o
+obj-$(CONFIG_IDE_H8300) += h8300/
obj-$(CONFIG_IDE_GENERIC) += ide-generic.o
obj-$(CONFIG_BLK_DEV_IDEDISK) += ide-disk.o
@@ -49,6 +45,20 @@
obj-$(CONFIG_BLK_DEV_IDETAPE) += ide-tape.o
obj-$(CONFIG_BLK_DEV_IDEFLOPPY) += ide-floppy.o
-obj-$(CONFIG_BLK_DEV_IDE) += legacy/ arm/ mips/
-obj-$(CONFIG_BLK_DEV_HD) += legacy/
-obj-$(CONFIG_ETRAX_IDE) += cris/
+ifeq ($(CONFIG_BLK_DEV_IDECS), y)
+ ide-cs-core-y += legacy/ide-cs.o
+ obj-y += ide-cs-core.o
+endif
+
+ifeq ($(CONFIG_BLK_DEV_PLATFORM), y)
+ ide-platform-core-y += legacy/ide_platform.o
+ obj-y += ide-platform-core.o
+endif
+
+obj-$(CONFIG_BLK_DEV_IDE) += arm/ mips/
+
+# old hd driver must be last
+ifeq ($(CONFIG_BLK_DEV_HD), y)
+ hd-core-y += legacy/hd.o
+ obj-y += hd-core.o
+endif
diff --git a/drivers/ide/arm/Makefile b/drivers/ide/arm/Makefile
index 6a78f07..5f63ad2 100644
--- a/drivers/ide/arm/Makefile
+++ b/drivers/ide/arm/Makefile
@@ -3,4 +3,8 @@
obj-$(CONFIG_BLK_DEV_IDE_RAPIDE) += rapide.o
obj-$(CONFIG_BLK_DEV_IDE_BAST) += bast-ide.o
+ifeq ($(CONFIG_IDE_ARM), m)
+ obj-m += ide_arm.o
+endif
+
EXTRA_CFLAGS := -Idrivers/ide
diff --git a/drivers/ide/arm/bast-ide.c b/drivers/ide/arm/bast-ide.c
index 48db616..45bf9c8 100644
--- a/drivers/ide/arm/bast-ide.c
+++ b/drivers/ide/arm/bast-ide.c
@@ -45,7 +45,7 @@
hw.io_ports[IDE_CONTROL_OFFSET] = aux + (6 * 0x20);
hw.irq = irq;
- ide_register_hw(&hw, NULL, 0, hwif);
+ ide_register_hw(&hw, NULL, hwif);
return 0;
}
diff --git a/drivers/ide/arm/icside.c b/drivers/ide/arm/icside.c
index 673402f..8a5c720 100644
--- a/drivers/ide/arm/icside.c
+++ b/drivers/ide/arm/icside.c
@@ -287,26 +287,10 @@
ide_xfer_verbose(xfer_mode), 2000 / drive->drive_data);
}
-static void icside_dma_host_off(ide_drive_t *drive)
+static void icside_dma_host_set(ide_drive_t *drive, int on)
{
}
-static void icside_dma_off_quietly(ide_drive_t *drive)
-{
- drive->using_dma = 0;
-}
-
-static void icside_dma_host_on(ide_drive_t *drive)
-{
-}
-
-static int icside_dma_on(ide_drive_t *drive)
-{
- drive->using_dma = 1;
-
- return 0;
-}
-
static int icside_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
@@ -422,10 +406,7 @@
hwif->dmatable_dma = 0;
hwif->set_dma_mode = icside_set_dma_mode;
- hwif->dma_host_off = icside_dma_host_off;
- hwif->dma_off_quietly = icside_dma_off_quietly;
- hwif->dma_host_on = icside_dma_host_on;
- hwif->ide_dma_on = icside_dma_on;
+ hwif->dma_host_set = icside_dma_host_set;
hwif->dma_setup = icside_dma_setup;
hwif->dma_exec_cmd = icside_dma_exec_cmd;
hwif->dma_start = icside_dma_start;
diff --git a/drivers/ide/arm/ide_arm.c b/drivers/ide/arm/ide_arm.c
index 8957cba..60f2497 100644
--- a/drivers/ide/arm/ide_arm.c
+++ b/drivers/ide/arm/ide_arm.c
@@ -24,12 +24,25 @@
# define IDE_ARM_IRQ IRQ_HARDDISK
#endif
-void __init ide_arm_init(void)
+static int __init ide_arm_init(void)
{
+ ide_hwif_t *hwif;
hw_regs_t hw;
+ u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
memset(&hw, 0, sizeof(hw));
ide_std_init_ports(&hw, IDE_ARM_IO, IDE_ARM_IO + 0x206);
hw.irq = IDE_ARM_IRQ;
- ide_register_hw(&hw, NULL, 1, NULL);
+
+ hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
+ if (hwif) {
+ ide_init_port_hw(hwif, &hw);
+ idx[0] = hwif->index;
+
+ ide_device_add(idx);
+ }
+
+ return 0;
}
+
+module_init(ide_arm_init);
diff --git a/drivers/ide/arm/rapide.c b/drivers/ide/arm/rapide.c
index 0775a3a..e6b56d1 100644
--- a/drivers/ide/arm/rapide.c
+++ b/drivers/ide/arm/rapide.c
@@ -13,26 +13,18 @@
#include <asm/ecard.h>
-static ide_hwif_t *
-rapide_locate_hwif(void __iomem *base, void __iomem *ctrl, unsigned int sz, int irq)
+static void rapide_setup_ports(hw_regs_t *hw, void __iomem *base,
+ void __iomem *ctrl, unsigned int sz, int irq)
{
unsigned long port = (unsigned long)base;
- ide_hwif_t *hwif = ide_find_port(port);
int i;
- if (hwif == NULL)
- goto out;
-
for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; i++) {
- hwif->io_ports[i] = port;
+ hw->io_ports[i] = port;
port += sz;
}
- hwif->io_ports[IDE_CONTROL_OFFSET] = (unsigned long)ctrl;
- hwif->irq = irq;
- hwif->mmio = 1;
- default_hwif_mmiops(hwif);
-out:
- return hwif;
+ hw->io_ports[IDE_CONTROL_OFFSET] = (unsigned long)ctrl;
+ hw->irq = irq;
}
static int __devinit
@@ -42,6 +34,7 @@
void __iomem *base;
int ret;
u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
+ hw_regs_t hw;
ret = ecard_request_resources(ec);
if (ret)
@@ -53,11 +46,17 @@
goto release;
}
- hwif = rapide_locate_hwif(base, base + 0x818, 1 << 6, ec->irq);
+ hwif = ide_find_port((unsigned long)base);
if (hwif) {
- hwif->hwif_data = base;
- hwif->gendev.parent = &ec->dev;
- hwif->noprobe = 0;
+ memset(&hw, 0, sizeof(hw));
+ rapide_setup_ports(&hw, base, base + 0x818, 1 << 6, ec->irq);
+ hw.chipset = ide_generic;
+ hw.dev = &ec->dev;
+
+ ide_init_port_hw(hwif, &hw);
+
+ hwif->mmio = 1;
+ default_hwif_mmiops(hwif);
idx[0] = hwif->index;
diff --git a/drivers/ide/cris/Makefile b/drivers/ide/cris/Makefile
index 6176e8d..20b9596 100644
--- a/drivers/ide/cris/Makefile
+++ b/drivers/ide/cris/Makefile
@@ -1,3 +1,3 @@
EXTRA_CFLAGS += -Idrivers/ide
-obj-y += ide-cris.o
+obj-$(CONFIG_IDE_ETRAX) += ide-cris.o
diff --git a/drivers/ide/cris/ide-cris.c b/drivers/ide/cris/ide-cris.c
index 325e608..8c3294c 100644
--- a/drivers/ide/cris/ide-cris.c
+++ b/drivers/ide/cris/ide-cris.c
@@ -673,9 +673,8 @@
static void cris_ide_output_data (ide_drive_t *drive, void *, unsigned int);
static void cris_atapi_input_bytes(ide_drive_t *drive, void *, unsigned int);
static void cris_atapi_output_bytes(ide_drive_t *drive, void *, unsigned int);
-static int cris_dma_on (ide_drive_t *drive);
-static void cris_dma_off(ide_drive_t *drive)
+static void cris_dma_host_set(ide_drive_t *drive, int on)
{
}
@@ -755,13 +754,11 @@
cris_ide_set_speed(TYPE_DMA, 0, strobe, hold);
}
-void __init
-init_e100_ide (void)
+static int __init init_e100_ide(void)
{
hw_regs_t hw;
- int ide_offsets[IDE_NR_PORTS];
- int h;
- int i;
+ int ide_offsets[IDE_NR_PORTS], h, i;
+ u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
printk("ide: ETRAX FS built-in ATA DMA controller\n");
@@ -778,9 +775,11 @@
ide_offsets,
0, 0, cris_ide_ack_intr,
ide_default_irq(0));
- ide_register_hw(&hw, NULL, 1, &hwif);
+ hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
if (hwif == NULL)
continue;
+ ide_init_port_data(hwif, hwif->index);
+ ide_init_port_hw(hwif, &hw);
hwif->mmio = 1;
hwif->chipset = ide_etrax100;
hwif->set_pio_mode = &cris_set_pio_mode;
@@ -789,6 +788,7 @@
hwif->ata_output_data = &cris_ide_output_data;
hwif->atapi_input_bytes = &cris_atapi_input_bytes;
hwif->atapi_output_bytes = &cris_atapi_output_bytes;
+ hwif->dma_host_set = &cris_dma_host_set;
hwif->ide_dma_end = &cris_dma_end;
hwif->dma_setup = &cris_dma_setup;
hwif->dma_exec_cmd = &cris_dma_exec_cmd;
@@ -799,9 +799,6 @@
hwif->OUTBSYNC = &cris_ide_outbsync;
hwif->INB = &cris_ide_inb;
hwif->INW = &cris_ide_inw;
- hwif->dma_host_off = &cris_dma_off;
- hwif->dma_host_on = &cris_dma_on;
- hwif->dma_off_quietly = &cris_dma_off;
hwif->cbl = ATA_CBL_PATA40;
hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
hwif->pio_mask = ATA_PIO4,
@@ -809,6 +806,8 @@
hwif->drives[1].autotune = 1;
hwif->ultra_mask = cris_ultra_mask;
hwif->mwdma_mask = 0x07; /* Multiword DMA 0-2 */
+
+ idx[h] = hwif->index;
}
/* Reset pulse */
@@ -821,14 +820,12 @@
cris_ide_set_speed(TYPE_PIO, ATA_PIO4_SETUP, ATA_PIO4_STROBE, ATA_PIO4_HOLD);
cris_ide_set_speed(TYPE_DMA, 0, ATA_DMA2_STROBE, ATA_DMA2_HOLD);
cris_ide_set_speed(TYPE_UDMA, ATA_UDMA2_CYC, ATA_UDMA2_DVS, 0);
-}
-static int cris_dma_on (ide_drive_t *drive)
-{
+ ide_device_add(idx);
+
return 0;
}
-
static cris_dma_descr_type mydescr __attribute__ ((__aligned__(16)));
/*
@@ -1060,3 +1057,5 @@
LED_DISK_READ(1);
}
}
+
+module_init(init_e100_ide);
diff --git a/drivers/ide/h8300/Makefile b/drivers/ide/h8300/Makefile
new file mode 100644
index 0000000..5eba16f
--- /dev/null
+++ b/drivers/ide/h8300/Makefile
@@ -0,0 +1,2 @@
+
+obj-$(CONFIG_IDE_H8300) += ide-h8300.o
diff --git a/drivers/ide/h8300/ide-h8300.c b/drivers/ide/h8300/ide-h8300.c
index 4a49b5c..4f6d019 100644
--- a/drivers/ide/h8300/ide-h8300.c
+++ b/drivers/ide/h8300/ide-h8300.c
@@ -84,11 +84,12 @@
hwif->INSL = NULL;
}
-void __init h8300_ide_init(void)
+static int __init h8300_ide_init(void)
{
hw_regs_t hw;
ide_hwif_t *hwif;
- int idx;
+ int index;
+ u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
if (!request_region(CONFIG_H8300_IDE_BASE, H8300_IDE_GAP*8, "ide-h8300"))
goto out_busy;
@@ -100,16 +101,28 @@
hw_setup(&hw);
/* register if */
- idx = ide_register_hw(&hw, NULL, 1, &hwif);
- if (idx == -1) {
+ hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
+ if (hwif == NULL) {
printk(KERN_ERR "ide-h8300: IDE I/F register failed\n");
- return;
+ return -ENOENT;
}
+ index = hwif->index;
+ ide_init_port_data(hwif, index);
+ ide_init_port_hw(hwif, &hw);
hwif_setup(hwif);
- printk(KERN_INFO "ide%d: H8/300 generic IDE interface\n", idx);
- return;
+ printk(KERN_INFO "ide%d: H8/300 generic IDE interface\n", index);
+
+ idx[0] = index;
+
+ ide_device_add(idx);
+
+ return 0;
out_busy:
printk(KERN_ERR "ide-h8300: IDE I/F resource already used.\n");
+
+ return -EBUSY;
}
+
+module_init(h8300_ide_init);
diff --git a/drivers/ide/ide-acpi.c b/drivers/ide/ide-acpi.c
index e0bb0cf..e888fc3 100644
--- a/drivers/ide/ide-acpi.c
+++ b/drivers/ide/ide-acpi.c
@@ -386,7 +386,7 @@
/* convert gtf to IDE Taskfile */
memcpy(&args.tf_array[7], >f->tfa, 7);
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
+ args.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
if (ide_noacpitfs) {
DEBPRINT("_GTF execution disabled\n");
diff --git a/drivers/ide/ide-disk.c b/drivers/ide/ide-disk.c
index d8fdd86..717e114 100644
--- a/drivers/ide/ide-disk.c
+++ b/drivers/ide/ide-disk.c
@@ -201,7 +201,7 @@
memset(&task, 0, sizeof(task));
task.tf_flags = IDE_TFLAG_NO_SELECT_MASK; /* FIXME? */
- task.tf_flags |= (IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE);
+ task.tf_flags |= (IDE_TFLAG_TF | IDE_TFLAG_DEVICE);
if (drive->select.b.lba) {
if (lba48) {
@@ -219,13 +219,8 @@
tf->lbal = (u8) block;
tf->lbam = (u8)(block >> 8);
tf->lbah = (u8)(block >> 16);
-#ifdef DEBUG
- printk("%s: 0x%02x%02x 0x%02x%02x%02x%02x%02x%02x\n",
- drive->name, tf->hob_nsect, tf->nsect,
- tf->hob_lbah, tf->hob_lbam, tf->hob_lbal,
- tf->lbah, tf->lbam, tf->lbal);
-#endif
- task.tf_flags |= (IDE_TFLAG_LBA48 | IDE_TFLAG_OUT_HOB);
+
+ task.tf_flags |= (IDE_TFLAG_LBA48 | IDE_TFLAG_HOB);
} else {
tf->nsect = nsectors & 0xff;
tf->lbal = block;
@@ -319,9 +314,9 @@
else
tf->command = WIN_READ_NATIVE_MAX;
tf->device = ATA_LBA;
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
+ args.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
if (lba48)
- args.tf_flags |= (IDE_TFLAG_LBA48 | IDE_TFLAG_OUT_HOB);
+ args.tf_flags |= (IDE_TFLAG_LBA48 | IDE_TFLAG_HOB);
/* submit command request */
ide_no_data_taskfile(drive, &args);
@@ -358,9 +353,9 @@
tf->command = WIN_SET_MAX;
}
tf->device |= ATA_LBA;
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
+ args.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
if (lba48)
- args.tf_flags |= (IDE_TFLAG_LBA48 | IDE_TFLAG_OUT_HOB);
+ args.tf_flags |= (IDE_TFLAG_LBA48 | IDE_TFLAG_HOB);
/* submit command request */
ide_no_data_taskfile(drive, &args);
/* if OK, compute maximum address value */
@@ -500,7 +495,7 @@
tf->lbam = SMART_LCYL_PASS;
tf->lbah = SMART_HCYL_PASS;
tf->command = WIN_SMART;
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
+ args.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
return ide_no_data_taskfile(drive, &args);
}
@@ -515,7 +510,7 @@
tf->lbam = SMART_LCYL_PASS;
tf->lbah = SMART_HCYL_PASS;
tf->command = WIN_SMART;
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
+ args.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
args.data_phase = TASKFILE_IN;
(void) smart_enable(drive);
return ide_raw_taskfile(drive, &args, buf, 1);
@@ -625,8 +620,10 @@
if (drive->special.b.set_multmode)
return -EBUSY;
+
ide_init_drive_cmd (&rq);
- rq.cmd_type = REQ_TYPE_ATA_CMD;
+ rq.cmd_type = REQ_TYPE_ATA_TASKFILE;
+
drive->mult_req = arg;
drive->special.b.set_multmode = 1;
(void) ide_do_drive_cmd (drive, &rq, ide_wait);
@@ -694,7 +691,7 @@
args.tf.feature = arg ?
SETFEATURES_EN_WCACHE : SETFEATURES_DIS_WCACHE;
args.tf.command = WIN_SETFEATURES;
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
+ args.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
err = ide_no_data_taskfile(drive, &args);
if (err == 0)
drive->wcache = arg;
@@ -714,7 +711,7 @@
args.tf.command = WIN_FLUSH_CACHE_EXT;
else
args.tf.command = WIN_FLUSH_CACHE;
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
+ args.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
return ide_no_data_taskfile(drive, &args);
}
@@ -729,7 +726,7 @@
args.tf.feature = arg ? SETFEATURES_EN_AAM : SETFEATURES_DIS_AAM;
args.tf.nsect = arg;
args.tf.command = WIN_SETFEATURES;
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
+ args.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
ide_no_data_taskfile(drive, &args);
drive->acoustic = arg;
return 0;
@@ -766,7 +763,6 @@
ide_add_setting(drive, "bios_head", SETTING_RW, TYPE_BYTE, 0, 255, 1, 1, &drive->bios_head, NULL);
ide_add_setting(drive, "bios_sect", SETTING_RW, TYPE_BYTE, 0, 63, 1, 1, &drive->bios_sect, NULL);
ide_add_setting(drive, "address", SETTING_RW, TYPE_BYTE, 0, 2, 1, 1, &drive->addressing, set_lba_addressing);
- ide_add_setting(drive, "bswap", SETTING_READ, TYPE_BYTE, 0, 1, 1, 1, &drive->bswap, NULL);
ide_add_setting(drive, "multcount", SETTING_RW, TYPE_BYTE, 0, id->max_multsect, 1, 1, &drive->mult_count, set_multcount);
ide_add_setting(drive, "nowerr", SETTING_RW, TYPE_BYTE, 0, 1, 1, 1, &drive->nowerr, set_nowerr);
ide_add_setting(drive, "lun", SETTING_RW, TYPE_INT, 0, 7, 1, 1, &drive->lun, NULL);
@@ -975,6 +971,17 @@
#endif
};
+static int idedisk_set_doorlock(ide_drive_t *drive, int on)
+{
+ ide_task_t task;
+
+ memset(&task, 0, sizeof(task));
+ task.tf.command = on ? WIN_DOORLOCK : WIN_DOORUNLOCK;
+ task.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
+
+ return ide_no_data_taskfile(drive, &task);
+}
+
static int idedisk_open(struct inode *inode, struct file *filp)
{
struct gendisk *disk = inode->i_bdev->bd_disk;
@@ -989,17 +996,13 @@
idkp->openers++;
if (drive->removable && idkp->openers == 1) {
- ide_task_t args;
- memset(&args, 0, sizeof(ide_task_t));
- args.tf.command = WIN_DOORLOCK;
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
check_disk_change(inode->i_bdev);
/*
* Ignore the return code from door_lock,
* since the open() has already succeeded,
* and the door_lock is irrelevant at this point.
*/
- if (drive->doorlocking && ide_no_data_taskfile(drive, &args))
+ if (drive->doorlocking && idedisk_set_doorlock(drive, 1))
drive->doorlocking = 0;
}
return 0;
@@ -1015,11 +1018,7 @@
ide_cacheflush_p(drive);
if (drive->removable && idkp->openers == 1) {
- ide_task_t args;
- memset(&args, 0, sizeof(ide_task_t));
- args.tf.command = WIN_DOORUNLOCK;
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
- if (drive->doorlocking && ide_no_data_taskfile(drive, &args))
+ if (drive->doorlocking && idedisk_set_doorlock(drive, 0))
drive->doorlocking = 0;
}
diff --git a/drivers/ide/ide-dma.c b/drivers/ide/ide-dma.c
index 18c78ad..5bf3203 100644
--- a/drivers/ide/ide-dma.c
+++ b/drivers/ide/ide-dma.c
@@ -153,13 +153,7 @@
if (!dma_stat) {
struct request *rq = HWGROUP(drive)->rq;
- if (rq->rq_disk) {
- ide_driver_t *drv;
-
- drv = *(ide_driver_t **)rq->rq_disk->private_data;
- drv->end_request(drive, 1, rq->nr_sectors);
- } else
- ide_end_request(drive, 1, rq->nr_sectors);
+ task_end_request(drive, rq, stat);
return ide_stopped;
}
printk(KERN_ERR "%s: dma_intr: bad DMA status (dma_stat=%x)\n",
@@ -408,23 +402,29 @@
}
/**
- * ide_dma_host_off - Generic DMA kill
+ * ide_dma_host_set - Enable/disable DMA on a host
* @drive: drive to control
*
- * Perform the generic IDE controller DMA off operation. This
- * works for most IDE bus mastering controllers
+ * Enable/disable DMA on an IDE controller following generic
+ * bus-mastering IDE controller behaviour.
*/
-void ide_dma_host_off(ide_drive_t *drive)
+void ide_dma_host_set(ide_drive_t *drive, int on)
{
ide_hwif_t *hwif = HWIF(drive);
u8 unit = (drive->select.b.unit & 0x01);
u8 dma_stat = hwif->INB(hwif->dma_status);
- hwif->OUTB((dma_stat & ~(1<<(5+unit))), hwif->dma_status);
+ if (on)
+ dma_stat |= (1 << (5 + unit));
+ else
+ dma_stat &= ~(1 << (5 + unit));
+
+ hwif->OUTB(dma_stat, hwif->dma_status);
}
-EXPORT_SYMBOL(ide_dma_host_off);
+EXPORT_SYMBOL_GPL(ide_dma_host_set);
+#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
/**
* ide_dma_off_quietly - Generic DMA kill
@@ -438,11 +438,10 @@
drive->using_dma = 0;
ide_toggle_bounce(drive, 0);
- drive->hwif->dma_host_off(drive);
+ drive->hwif->dma_host_set(drive, 0);
}
EXPORT_SYMBOL(ide_dma_off_quietly);
-#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
/**
* ide_dma_off - disable DMA on a device
@@ -455,52 +454,29 @@
void ide_dma_off(ide_drive_t *drive)
{
printk(KERN_INFO "%s: DMA disabled\n", drive->name);
- drive->hwif->dma_off_quietly(drive);
+ ide_dma_off_quietly(drive);
}
EXPORT_SYMBOL(ide_dma_off);
-#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
/**
- * ide_dma_host_on - Enable DMA on a host
- * @drive: drive to enable for DMA
- *
- * Enable DMA on an IDE controller following generic bus mastering
- * IDE controller behaviour
- */
-
-void ide_dma_host_on(ide_drive_t *drive)
-{
- if (drive->using_dma) {
- ide_hwif_t *hwif = HWIF(drive);
- u8 unit = (drive->select.b.unit & 0x01);
- u8 dma_stat = hwif->INB(hwif->dma_status);
-
- hwif->OUTB((dma_stat|(1<<(5+unit))), hwif->dma_status);
- }
-}
-
-EXPORT_SYMBOL(ide_dma_host_on);
-
-/**
- * __ide_dma_on - Enable DMA on a device
+ * ide_dma_on - Enable DMA on a device
* @drive: drive to enable DMA on
*
* Enable IDE DMA for a device on this IDE controller.
*/
-
-int __ide_dma_on (ide_drive_t *drive)
+
+void ide_dma_on(ide_drive_t *drive)
{
drive->using_dma = 1;
ide_toggle_bounce(drive, 1);
- drive->hwif->dma_host_on(drive);
-
- return 0;
+ drive->hwif->dma_host_set(drive, 1);
}
-EXPORT_SYMBOL(__ide_dma_on);
+EXPORT_SYMBOL(ide_dma_on);
+#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
/**
* ide_dma_setup - begin a DMA phase
* @drive: target device
@@ -755,6 +731,7 @@
static int ide_tune_dma(ide_drive_t *drive)
{
+ ide_hwif_t *hwif = drive->hwif;
u8 speed;
if (noautodma || drive->nodma || (drive->id->capability & 1) == 0)
@@ -767,15 +744,21 @@
if (ide_id_dma_bug(drive))
return 0;
- if (drive->hwif->host_flags & IDE_HFLAG_TRUST_BIOS_FOR_DMA)
+ if (hwif->host_flags & IDE_HFLAG_TRUST_BIOS_FOR_DMA)
return config_drive_for_dma(drive);
speed = ide_max_dma_mode(drive);
- if (!speed)
- return 0;
+ if (!speed) {
+ /* is this really correct/needed? */
+ if ((hwif->host_flags & IDE_HFLAG_CY82C693) &&
+ ide_dma_good_drive(drive))
+ return 1;
+ else
+ return 0;
+ }
- if (drive->hwif->host_flags & IDE_HFLAG_NO_SET_MODE)
+ if (hwif->host_flags & IDE_HFLAG_NO_SET_MODE)
return 0;
if (ide_set_dma_mode(drive, speed))
@@ -820,7 +803,6 @@
int ide_set_dma(ide_drive_t *drive)
{
- ide_hwif_t *hwif = drive->hwif;
int rc;
/*
@@ -829,13 +811,15 @@
* things, if not checked and cleared.
* PARANOIA!!!
*/
- hwif->dma_off_quietly(drive);
+ ide_dma_off_quietly(drive);
rc = ide_dma_check(drive);
if (rc)
return rc;
- return hwif->ide_dma_on(drive);
+ ide_dma_on(drive);
+
+ return 0;
}
#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
@@ -972,14 +956,8 @@
if (!(hwif->dma_prdtable))
hwif->dma_prdtable = (hwif->dma_base + 4);
- if (!hwif->dma_off_quietly)
- hwif->dma_off_quietly = &ide_dma_off_quietly;
- if (!hwif->dma_host_off)
- hwif->dma_host_off = &ide_dma_host_off;
- if (!hwif->ide_dma_on)
- hwif->ide_dma_on = &__ide_dma_on;
- if (!hwif->dma_host_on)
- hwif->dma_host_on = &ide_dma_host_on;
+ if (!hwif->dma_host_set)
+ hwif->dma_host_set = &ide_dma_host_set;
if (!hwif->dma_setup)
hwif->dma_setup = &ide_dma_setup;
if (!hwif->dma_exec_cmd)
diff --git a/drivers/ide/ide-generic.c b/drivers/ide/ide-generic.c
index 0f72b98..bb30c29 100644
--- a/drivers/ide/ide-generic.c
+++ b/drivers/ide/ide-generic.c
@@ -14,10 +14,16 @@
static int __init ide_generic_init(void)
{
+ u8 idx[MAX_HWIFS];
+ int i;
+
if (ide_hwifs[0].io_ports[IDE_DATA_OFFSET])
ide_get_lock(NULL, NULL); /* for atari only */
- (void)ideprobe_init();
+ for (i = 0; i < MAX_HWIFS; i++)
+ idx[i] = ide_hwifs[i].present ? 0xff : i;
+
+ ide_device_add_all(idx);
if (ide_hwifs[0].io_ports[IDE_DATA_OFFSET])
ide_release_lock(); /* for atari only */
diff --git a/drivers/ide/ide-io.c b/drivers/ide/ide-io.c
index 2711b5a..6f8f544 100644
--- a/drivers/ide/ide-io.c
+++ b/drivers/ide/ide-io.c
@@ -75,7 +75,7 @@
*/
if (drive->state == DMA_PIO_RETRY && drive->retry_pio <= 3) {
drive->state = 0;
- HWGROUP(drive)->hwif->ide_dma_on(drive);
+ ide_dma_on(drive);
}
if (!end_that_request_chunk(rq, uptodate, nr_bytes)) {
@@ -219,7 +219,7 @@
* we could be smarter and check for current xfer_speed
* in struct drive etc...
*/
- if (drive->hwif->ide_dma_on == NULL)
+ if (drive->hwif->dma_host_set == NULL)
break;
/*
* TODO: respect ->using_dma setting
@@ -231,7 +231,7 @@
return ide_stopped;
out_do_tf:
- args->tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
+ args->tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
args->data_phase = TASKFILE_NO_DATA;
return do_rw_taskfile(drive, args);
}
@@ -354,7 +354,6 @@
void ide_end_drive_cmd (ide_drive_t *drive, u8 stat, u8 err)
{
- ide_hwif_t *hwif = HWIF(drive);
unsigned long flags;
struct request *rq;
@@ -362,17 +361,7 @@
rq = HWGROUP(drive)->rq;
spin_unlock_irqrestore(&ide_lock, flags);
- if (rq->cmd_type == REQ_TYPE_ATA_CMD) {
- u8 *args = (u8 *) rq->buffer;
- if (rq->errors == 0)
- rq->errors = !OK_STAT(stat,READY_STAT,BAD_STAT);
-
- if (args) {
- args[0] = stat;
- args[1] = err;
- args[2] = hwif->INB(IDE_NSECTOR_REG);
- }
- } else if (rq->cmd_type == REQ_TYPE_ATA_TASKFILE) {
+ if (rq->cmd_type == REQ_TYPE_ATA_TASKFILE) {
ide_task_t *args = (ide_task_t *) rq->special;
if (rq->errors == 0)
rq->errors = !OK_STAT(stat,READY_STAT,BAD_STAT);
@@ -383,10 +372,6 @@
tf->error = err;
tf->status = stat;
- args->tf_flags |= (IDE_TFLAG_IN_TF|IDE_TFLAG_IN_DEVICE);
- if (args->tf_flags & IDE_TFLAG_LBA48)
- args->tf_flags |= IDE_TFLAG_IN_HOB;
-
ide_tf_read(drive, args);
}
} else if (blk_pm_request(rq)) {
@@ -626,42 +611,6 @@
return __ide_abort(drive, rq);
}
-/**
- * drive_cmd_intr - drive command completion interrupt
- * @drive: drive the completion interrupt occurred on
- *
- * drive_cmd_intr() is invoked on completion of a special DRIVE_CMD.
- * We do any necessary data reading and then wait for the drive to
- * go non busy. At that point we may read the error data and complete
- * the request
- */
-
-static ide_startstop_t drive_cmd_intr (ide_drive_t *drive)
-{
- struct request *rq = HWGROUP(drive)->rq;
- ide_hwif_t *hwif = HWIF(drive);
- u8 *args = (u8 *) rq->buffer;
- u8 stat = hwif->INB(IDE_STATUS_REG);
- int retries = 10;
-
- local_irq_enable_in_hardirq();
- if (rq->cmd_type == REQ_TYPE_ATA_CMD &&
- (stat & DRQ_STAT) && args && args[3]) {
- u8 io_32bit = drive->io_32bit;
- drive->io_32bit = 0;
- hwif->ata_input_data(drive, &args[4], args[3] * SECTOR_WORDS);
- drive->io_32bit = io_32bit;
- while (((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) && retries--)
- udelay(100);
- }
-
- if (!OK_STAT(stat, READY_STAT, BAD_STAT))
- return ide_error(drive, "drive_cmd", stat);
- /* calls ide_end_drive_cmd */
- ide_end_drive_cmd(drive, stat, hwif->INB(IDE_ERROR_REG));
- return ide_stopped;
-}
-
static void ide_tf_set_specify_cmd(ide_drive_t *drive, struct ide_taskfile *tf)
{
tf->nsect = drive->sect;
@@ -710,7 +659,7 @@
return ide_stopped;
}
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE |
+ args.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE |
IDE_TFLAG_CUSTOM_HANDLER;
do_rw_taskfile(drive, &args);
@@ -787,7 +736,7 @@
if (hwif->host_flags & IDE_HFLAG_SET_PIO_MODE_KEEP_DMA) {
if (keep_dma)
- hwif->ide_dma_on(drive);
+ ide_dma_on(drive);
}
}
@@ -847,16 +796,9 @@
struct request *rq)
{
ide_hwif_t *hwif = HWIF(drive);
- u8 *args = rq->buffer;
- ide_task_t ltask;
- struct ide_taskfile *tf = <ask.tf;
+ ide_task_t *task = rq->special;
- if (rq->cmd_type == REQ_TYPE_ATA_TASKFILE) {
- ide_task_t *task = rq->special;
-
- if (task == NULL)
- goto done;
-
+ if (task) {
hwif->data_phase = task->data_phase;
switch (hwif->data_phase) {
@@ -873,33 +815,6 @@
return do_rw_taskfile(drive, task);
}
- if (args == NULL)
- goto done;
-
- memset(<ask, 0, sizeof(ltask));
- if (rq->cmd_type == REQ_TYPE_ATA_CMD) {
-#ifdef DEBUG
- printk("%s: DRIVE_CMD\n", drive->name);
-#endif
- tf->feature = args[2];
- if (args[0] == WIN_SMART) {
- tf->nsect = args[3];
- tf->lbal = args[1];
- tf->lbam = 0x4f;
- tf->lbah = 0xc2;
- ltask.tf_flags = IDE_TFLAG_OUT_TF;
- } else {
- tf->nsect = args[1];
- ltask.tf_flags = IDE_TFLAG_OUT_FEATURE |
- IDE_TFLAG_OUT_NSECT;
- }
- }
- tf->command = args[0];
- ide_tf_load(drive, <ask);
- ide_execute_command(drive, args[0], &drive_cmd_intr, WAIT_WORSTCASE, NULL);
- return ide_started;
-
-done:
/*
* NULL is actually a valid way of waiting for
* all current requests to be flushed from the queue.
@@ -939,8 +854,7 @@
if (rc)
printk(KERN_WARNING "%s: bus not ready on wakeup\n", drive->name);
SELECT_DRIVE(drive);
- if (IDE_CONTROL_REG)
- HWIF(drive)->OUTB(drive->ctl, IDE_CONTROL_REG);
+ ide_set_irq(drive, 1);
rc = ide_wait_not_busy(HWIF(drive), 100000);
if (rc)
printk(KERN_WARNING "%s: drive not ready on wakeup\n", drive->name);
@@ -1004,8 +918,7 @@
if (drive->current_speed == 0xff)
ide_config_drive_speed(drive, drive->desired_speed);
- if (rq->cmd_type == REQ_TYPE_ATA_CMD ||
- rq->cmd_type == REQ_TYPE_ATA_TASKFILE)
+ if (rq->cmd_type == REQ_TYPE_ATA_TASKFILE)
return execute_drive_cmd(drive, rq);
else if (blk_pm_request(rq)) {
struct request_pm_state *pm = rq->data;
@@ -1213,15 +1126,13 @@
}
again:
hwif = HWIF(drive);
- if (hwgroup->hwif->sharing_irq &&
- hwif != hwgroup->hwif &&
- hwif->io_ports[IDE_CONTROL_OFFSET]) {
+ if (hwgroup->hwif->sharing_irq && hwif != hwgroup->hwif) {
/*
* set nIEN for previous hwif, drives in the
* quirk_list may not like intr setups/cleanups
*/
if (drive->quirk_list != 1)
- hwif->OUTB(drive->ctl | 2, IDE_CONTROL_REG);
+ ide_set_irq(drive, 0);
}
hwgroup->hwif = hwif;
hwgroup->drive = drive;
@@ -1334,7 +1245,7 @@
*/
drive->retry_pio++;
drive->state = DMA_PIO_RETRY;
- hwif->dma_off_quietly(drive);
+ ide_dma_off_quietly(drive);
/*
* un-busy drive etc (hwgroup->busy is cleared on return) and
@@ -1679,7 +1590,6 @@
void ide_init_drive_cmd (struct request *rq)
{
memset(rq, 0, sizeof(*rq));
- rq->cmd_type = REQ_TYPE_ATA_CMD;
rq->ref_count = 1;
}
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index c97c071..e2a7e95 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -619,7 +619,7 @@
int ide_ata66_check (ide_drive_t *drive, ide_task_t *args)
{
if (args->tf.command == WIN_SETFEATURES &&
- args->tf.lbal > XFER_UDMA_2 &&
+ args->tf.nsect > XFER_UDMA_2 &&
args->tf.feature == SETFEATURES_XFER) {
if (eighty_ninty_three(drive) == 0) {
printk(KERN_WARNING "%s: UDMA speeds >UDMA33 cannot "
@@ -639,7 +639,7 @@
int set_transfer (ide_drive_t *drive, ide_task_t *args)
{
if (args->tf.command == WIN_SETFEATURES &&
- args->tf.lbal >= XFER_SW_DMA_0 &&
+ args->tf.nsect >= XFER_SW_DMA_0 &&
args->tf.feature == SETFEATURES_XFER &&
(drive->id->dma_ultra ||
drive->id->dma_mword ||
@@ -688,8 +688,7 @@
*/
SELECT_MASK(drive, 1);
- if (IDE_CONTROL_REG)
- hwif->OUTB(drive->ctl,IDE_CONTROL_REG);
+ ide_set_irq(drive, 1);
msleep(50);
hwif->OUTB(WIN_IDENTIFY, IDE_COMMAND_REG);
timeout = jiffies + WAIT_WORSTCASE;
@@ -742,8 +741,8 @@
// msleep(50);
#ifdef CONFIG_BLK_DEV_IDEDMA
- if (hwif->ide_dma_on) /* check if host supports DMA */
- hwif->dma_host_off(drive);
+ if (hwif->dma_host_set) /* check if host supports DMA */
+ hwif->dma_host_set(drive, 0);
#endif
/* Skip setting PIO flow-control modes on pre-EIDE drives */
@@ -772,13 +771,12 @@
SELECT_DRIVE(drive);
SELECT_MASK(drive, 0);
udelay(1);
- if (IDE_CONTROL_REG)
- hwif->OUTB(drive->ctl | 2, IDE_CONTROL_REG);
+ ide_set_irq(drive, 0);
hwif->OUTB(speed, IDE_NSECTOR_REG);
hwif->OUTB(SETFEATURES_XFER, IDE_FEATURE_REG);
hwif->OUTBSYNC(drive, WIN_SETFEATURES, IDE_COMMAND_REG);
- if ((IDE_CONTROL_REG) && (drive->quirk_list == 2))
- hwif->OUTB(drive->ctl, IDE_CONTROL_REG);
+ if (drive->quirk_list == 2)
+ ide_set_irq(drive, 1);
error = __ide_wait_stat(drive, drive->ready_stat,
BUSY_STAT|DRQ_STAT|ERR_STAT,
@@ -799,10 +797,11 @@
skip:
#ifdef CONFIG_BLK_DEV_IDEDMA
- if (speed >= XFER_SW_DMA_0)
- hwif->dma_host_on(drive);
- else if (hwif->ide_dma_on) /* check if host supports DMA */
- hwif->dma_off_quietly(drive);
+ if ((speed >= XFER_SW_DMA_0 || (hwif->host_flags & IDE_HFLAG_VDMA)) &&
+ drive->using_dma)
+ hwif->dma_host_set(drive, 1);
+ else if (hwif->dma_host_set) /* check if host supports DMA */
+ ide_dma_off_quietly(drive);
#endif
switch(speed) {
@@ -1012,10 +1011,10 @@
{
#ifdef CONFIG_BLK_DEV_IDEDMA
if (drive->crc_count) {
- drive->hwif->dma_off_quietly(drive);
+ ide_dma_off_quietly(drive);
ide_set_xfer_rate(drive, ide_auto_reduce_xfer(drive));
if (drive->current_speed >= XFER_SW_DMA_0)
- (void) HWIF(drive)->ide_dma_on(drive);
+ ide_dma_on(drive);
} else
ide_dma_off(drive);
#endif
diff --git a/drivers/ide/ide-lib.c b/drivers/ide/ide-lib.c
index a3bd8e8..9b44fbd 100644
--- a/drivers/ide/ide-lib.c
+++ b/drivers/ide/ide-lib.c
@@ -454,8 +454,7 @@
static void ide_dump_opcode(ide_drive_t *drive)
{
struct request *rq;
- u8 opcode = 0;
- int found = 0;
+ ide_task_t *task = NULL;
spin_lock(&ide_lock);
rq = NULL;
@@ -464,25 +463,15 @@
spin_unlock(&ide_lock);
if (!rq)
return;
- if (rq->cmd_type == REQ_TYPE_ATA_CMD) {
- char *args = rq->buffer;
- if (args) {
- opcode = args[0];
- found = 1;
- }
- } else if (rq->cmd_type == REQ_TYPE_ATA_TASKFILE) {
- ide_task_t *args = rq->special;
- if (args) {
- opcode = args->tf.command;
- found = 1;
- }
- }
+
+ if (rq->cmd_type == REQ_TYPE_ATA_TASKFILE)
+ task = rq->special;
printk("ide: failed opcode was: ");
- if (!found)
- printk("unknown\n");
+ if (task == NULL)
+ printk(KERN_CONT "unknown\n");
else
- printk("0x%02x\n", opcode);
+ printk(KERN_CONT "0x%02x\n", task->tf.command);
}
u64 ide_get_lba_addr(struct ide_taskfile *tf, int lba48)
diff --git a/drivers/ide/ide-pnp.c b/drivers/ide/ide-pnp.c
index e245521..cbbb0f7 100644
--- a/drivers/ide/ide-pnp.c
+++ b/drivers/ide/ide-pnp.c
@@ -31,7 +31,6 @@
{
hw_regs_t hw;
ide_hwif_t *hwif;
- int index;
if (!(pnp_port_valid(dev, 0) && pnp_port_valid(dev, 1) && pnp_irq_valid(dev, 0)))
return -1;
@@ -41,11 +40,19 @@
pnp_port_start(dev, 1));
hw.irq = pnp_irq(dev, 0);
- index = ide_register_hw(&hw, NULL, 1, &hwif);
+ hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
+ if (hwif) {
+ u8 index = hwif->index;
+ u8 idx[4] = { index, 0xff, 0xff, 0xff };
- if (index != -1) {
- printk(KERN_INFO "ide%d: generic PnP IDE interface\n", index);
+ ide_init_port_data(hwif, index);
+ ide_init_port_hw(hwif, &hw);
+
+ printk(KERN_INFO "ide%d: generic PnP IDE interface\n", index);
pnp_set_drvdata(dev,hwif);
+
+ ide_device_add(idx);
+
return 0;
}
@@ -68,12 +75,15 @@
.remove = idepnp_remove,
};
-void __init pnpide_init(void)
+static int __init pnpide_init(void)
{
- pnp_register_driver(&idepnp_driver);
+ return pnp_register_driver(&idepnp_driver);
}
-void __exit pnpide_exit(void)
+static void __exit pnpide_exit(void)
{
pnp_unregister_driver(&idepnp_driver);
}
+
+module_init(pnpide_init);
+module_exit(pnpide_exit);
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index 0379d1f..edf650b 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -235,9 +235,6 @@
drive->media = ide_disk;
printk("%s DISK drive\n", (id->config == 0x848a) ? "CFA" : "ATA" );
- if (hwif->quirkproc)
- drive->quirk_list = hwif->quirkproc(drive);
-
return;
err_misc:
@@ -353,22 +350,19 @@
* the irq handler isn't expecting.
*/
if (IDE_CONTROL_REG) {
- u8 ctl = drive->ctl | 2;
if (!hwif->irq) {
autoprobe = 1;
cookie = probe_irq_on();
- /* enable device irq */
- ctl &= ~2;
}
- hwif->OUTB(ctl, IDE_CONTROL_REG);
+ ide_set_irq(drive, autoprobe);
}
retval = actual_try_to_identify(drive, cmd);
if (autoprobe) {
int irq;
- /* mask device irq */
- hwif->OUTB(drive->ctl|2, IDE_CONTROL_REG);
+
+ ide_set_irq(drive, 0);
/* clear drive IRQ */
(void) hwif->INB(IDE_STATUS_REG);
udelay(5);
@@ -388,6 +382,20 @@
return retval;
}
+static int ide_busy_sleep(ide_hwif_t *hwif)
+{
+ unsigned long timeout = jiffies + WAIT_WORSTCASE;
+ u8 stat;
+
+ do {
+ msleep(50);
+ stat = hwif->INB(hwif->io_ports[IDE_STATUS_OFFSET]);
+ if ((stat & BUSY_STAT) == 0)
+ return 0;
+ } while (time_before(jiffies, timeout));
+
+ return 1;
+}
/**
* do_probe - probe an IDE device
@@ -456,7 +464,6 @@
if ((rc == 1 && cmd == WIN_PIDENTIFY) &&
((drive->autotune == IDE_TUNE_DEFAULT) ||
(drive->autotune == IDE_TUNE_AUTO))) {
- unsigned long timeout;
printk("%s: no response (status = 0x%02x), "
"resetting drive\n", drive->name,
hwif->INB(IDE_STATUS_REG));
@@ -464,10 +471,7 @@
hwif->OUTB(drive->select.all, IDE_SELECT_REG);
msleep(50);
hwif->OUTB(WIN_SRST, IDE_COMMAND_REG);
- timeout = jiffies;
- while (((hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) &&
- time_before(jiffies, timeout + WAIT_WORSTCASE))
- msleep(50);
+ (void)ide_busy_sleep(hwif);
rc = try_to_identify(drive, cmd);
}
if (rc == 1)
@@ -495,20 +499,16 @@
static void enable_nest (ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
- unsigned long timeout;
printk("%s: enabling %s -- ", hwif->name, drive->id->model);
SELECT_DRIVE(drive);
msleep(50);
hwif->OUTB(EXABYTE_ENABLE_NEST, IDE_COMMAND_REG);
- timeout = jiffies + WAIT_WORSTCASE;
- do {
- if (time_after(jiffies, timeout)) {
- printk("failed (timeout)\n");
- return;
- }
- msleep(50);
- } while ((hwif->INB(IDE_STATUS_REG)) & BUSY_STAT);
+
+ if (ide_busy_sleep(hwif)) {
+ printk(KERN_CONT "failed (timeout)\n");
+ return;
+ }
msleep(50);
@@ -656,8 +656,7 @@
/* Ignore disks that we will not probe for later. */
if (!drive->noprobe || drive->present) {
SELECT_DRIVE(drive);
- if (IDE_CONTROL_REG)
- hwif->OUTB(drive->ctl, IDE_CONTROL_REG);
+ ide_set_irq(drive, 1);
mdelay(2);
rc = ide_wait_not_busy(hwif, 35000);
if (rc)
@@ -676,19 +675,18 @@
/**
* ide_undecoded_slave - look for bad CF adapters
- * @hwif: interface
+ * @drive1: drive
*
* Analyse the drives on the interface and attempt to decide if we
* have the same drive viewed twice. This occurs with crap CF adapters
* and PCMCIA sometimes.
*/
-void ide_undecoded_slave(ide_hwif_t *hwif)
+void ide_undecoded_slave(ide_drive_t *drive1)
{
- ide_drive_t *drive0 = &hwif->drives[0];
- ide_drive_t *drive1 = &hwif->drives[1];
+ ide_drive_t *drive0 = &drive1->hwif->drives[0];
- if (drive0->present == 0 || drive1->present == 0)
+ if ((drive1->dn & 1) == 0 || drive0->present == 0)
return;
/* If the models don't match they are not the same product */
@@ -791,18 +789,11 @@
}
}
if (hwif->io_ports[IDE_CONTROL_OFFSET] && hwif->reset) {
- unsigned long timeout = jiffies + WAIT_WORSTCASE;
- u8 stat;
-
printk(KERN_WARNING "%s: reset\n", hwif->name);
hwif->OUTB(12, hwif->io_ports[IDE_CONTROL_OFFSET]);
udelay(10);
hwif->OUTB(8, hwif->io_ports[IDE_CONTROL_OFFSET]);
- do {
- msleep(50);
- stat = hwif->INB(hwif->io_ports[IDE_STATUS_OFFSET]);
- } while ((stat & BUSY_STAT) && time_after(timeout, jiffies));
-
+ (void)ide_busy_sleep(hwif);
}
local_irq_restore(flags);
/*
@@ -817,8 +808,12 @@
return;
}
- if (hwif->fixup)
- hwif->fixup(hwif);
+ for (unit = 0; unit < MAX_DRIVES; unit++) {
+ ide_drive_t *drive = &hwif->drives[unit];
+
+ if (drive->present && hwif->quirkproc)
+ hwif->quirkproc(drive);
+ }
for (unit = 0; unit < MAX_DRIVES; ++unit) {
ide_drive_t *drive = &hwif->drives[unit];
@@ -833,7 +828,7 @@
drive->nice1 = 1;
- if (hwif->ide_dma_on)
+ if (hwif->dma_host_set)
ide_set_dma(drive);
}
}
@@ -848,25 +843,6 @@
}
}
-static int hwif_init(ide_hwif_t *hwif);
-static void hwif_register_devices(ide_hwif_t *hwif);
-
-static int probe_hwif_init(ide_hwif_t *hwif)
-{
- probe_hwif(hwif);
-
- if (!hwif_init(hwif)) {
- printk(KERN_INFO "%s: failed to initialize IDE interface\n",
- hwif->name);
- return -1;
- }
-
- if (hwif->present)
- hwif_register_devices(hwif);
-
- return 0;
-}
-
#if MAX_HWIFS > 1
/*
* save_match() is used to simplify logic in init_irq() below.
@@ -1359,54 +1335,63 @@
}
}
-int ideprobe_init (void)
+int ide_device_add_all(u8 *idx)
{
- unsigned int index;
- int probe[MAX_HWIFS];
+ ide_hwif_t *hwif;
+ int i, rc = 0;
- memset(probe, 0, MAX_HWIFS * sizeof(int));
- for (index = 0; index < MAX_HWIFS; ++index)
- probe[index] = !ide_hwifs[index].present;
+ for (i = 0; i < MAX_HWIFS; i++) {
+ if (idx[i] == 0xff)
+ continue;
- for (index = 0; index < MAX_HWIFS; ++index)
- if (probe[index])
- probe_hwif(&ide_hwifs[index]);
- for (index = 0; index < MAX_HWIFS; ++index)
- if (probe[index])
- hwif_init(&ide_hwifs[index]);
- for (index = 0; index < MAX_HWIFS; ++index) {
- if (probe[index]) {
- ide_hwif_t *hwif = &ide_hwifs[index];
- if (!hwif->present)
- continue;
- if (hwif->chipset == ide_unknown || hwif->chipset == ide_forced)
+ probe_hwif(&ide_hwifs[idx[i]]);
+ }
+
+ for (i = 0; i < MAX_HWIFS; i++) {
+ if (idx[i] == 0xff)
+ continue;
+
+ hwif = &ide_hwifs[idx[i]];
+
+ if (hwif_init(hwif) == 0) {
+ printk(KERN_INFO "%s: failed to initialize IDE "
+ "interface\n", hwif->name);
+ rc = -1;
+ continue;
+ }
+ }
+
+ for (i = 0; i < MAX_HWIFS; i++) {
+ if (idx[i] == 0xff)
+ continue;
+
+ hwif = &ide_hwifs[idx[i]];
+
+ if (hwif->present) {
+ if (hwif->chipset == ide_unknown ||
+ hwif->chipset == ide_forced)
hwif->chipset = ide_generic;
hwif_register_devices(hwif);
}
}
- for (index = 0; index < MAX_HWIFS; ++index)
- if (probe[index])
- ide_proc_register_port(&ide_hwifs[index]);
- return 0;
-}
-EXPORT_SYMBOL_GPL(ideprobe_init);
-
-int ide_device_add(u8 idx[4])
-{
- int i, rc = 0;
-
- for (i = 0; i < 4; i++) {
- if (idx[i] != 0xff)
- rc |= probe_hwif_init(&ide_hwifs[idx[i]]);
- }
-
- for (i = 0; i < 4; i++) {
+ for (i = 0; i < MAX_HWIFS; i++) {
if (idx[i] != 0xff)
ide_proc_register_port(&ide_hwifs[idx[i]]);
}
return rc;
}
+EXPORT_SYMBOL_GPL(ide_device_add_all);
+int ide_device_add(u8 idx[4])
+{
+ u8 idx_all[MAX_HWIFS];
+ int i;
+
+ for (i = 0; i < MAX_HWIFS; i++)
+ idx_all[i] = (i < 4) ? idx[i] : 0xff;
+
+ return ide_device_add_all(idx_all);
+}
EXPORT_SYMBOL_GPL(ide_device_add);
diff --git a/drivers/ide/ide-proc.c b/drivers/ide/ide-proc.c
index a4007d3..aa663e7 100644
--- a/drivers/ide/ide-proc.c
+++ b/drivers/ide/ide-proc.c
@@ -346,14 +346,20 @@
static int set_xfer_rate (ide_drive_t *drive, int arg)
{
+ ide_task_t task;
int err;
if (arg < 0 || arg > 70)
return -EINVAL;
- err = ide_wait_cmd(drive,
- WIN_SETFEATURES, (u8) arg,
- SETFEATURES_XFER, 0, NULL);
+ memset(&task, 0, sizeof(task));
+ task.tf.command = WIN_SETFEATURES;
+ task.tf.feature = SETFEATURES_XFER;
+ task.tf.nsect = (u8)arg;
+ task.tf_flags = IDE_TFLAG_OUT_FEATURE | IDE_TFLAG_OUT_NSECT |
+ IDE_TFLAG_IN_NSECT;
+
+ err = ide_no_data_taskfile(drive, &task);
if (!err && arg) {
ide_set_xfer_rate(drive, (u8) arg);
diff --git a/drivers/ide/ide-scan-pci.c b/drivers/ide/ide-scan-pci.c
new file mode 100644
index 0000000..7ffa332
--- /dev/null
+++ b/drivers/ide/ide-scan-pci.c
@@ -0,0 +1,121 @@
+/*
+ * support for probing IDE PCI devices in the PCI bus order
+ *
+ * Copyright (c) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (c) 1995-1998 Mark Lord
+ *
+ * May be copied or modified under the terms of the GNU General Public License
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/ide.h>
+
+/*
+ * Module interfaces
+ */
+
+static int pre_init = 1; /* Before first ordered IDE scan */
+static LIST_HEAD(ide_pci_drivers);
+
+/*
+ * __ide_pci_register_driver - attach IDE driver
+ * @driver: pci driver
+ * @module: owner module of the driver
+ *
+ * Registers a driver with the IDE layer. The IDE layer arranges that
+ * boot time setup is done in the expected device order and then
+ * hands the controllers off to the core PCI code to do the rest of
+ * the work.
+ *
+ * Returns are the same as for pci_register_driver
+ */
+
+int __ide_pci_register_driver(struct pci_driver *driver, struct module *module,
+ const char *mod_name)
+{
+ if (!pre_init)
+ return __pci_register_driver(driver, module, mod_name);
+ driver->driver.owner = module;
+ list_add_tail(&driver->node, &ide_pci_drivers);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(__ide_pci_register_driver);
+
+/**
+ * ide_scan_pcidev - find an IDE driver for a device
+ * @dev: PCI device to check
+ *
+ * Look for an IDE driver to handle the device we are considering.
+ * This is only used during boot up to get the ordering correct. After
+ * boot up the pci layer takes over the job.
+ */
+
+static int __init ide_scan_pcidev(struct pci_dev *dev)
+{
+ struct list_head *l;
+ struct pci_driver *d;
+
+ list_for_each(l, &ide_pci_drivers) {
+ d = list_entry(l, struct pci_driver, node);
+ if (d->id_table) {
+ const struct pci_device_id *id =
+ pci_match_id(d->id_table, dev);
+
+ if (id != NULL && d->probe(dev, id) >= 0) {
+ dev->driver = d;
+ pci_dev_get(dev);
+ return 1;
+ }
+ }
+ }
+ return 0;
+}
+
+/**
+ * ide_scan_pcibus - perform the initial IDE driver scan
+ *
+ * Perform the initial bus rather than driver ordered scan of the
+ * PCI drivers. After this all IDE pci handling becomes standard
+ * module ordering not traditionally ordered.
+ */
+
+int __init ide_scan_pcibus(void)
+{
+ struct pci_dev *dev = NULL;
+ struct pci_driver *d;
+ struct list_head *l, *n;
+
+ pre_init = 0;
+ if (!ide_scan_direction)
+ while ((dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev)))
+ ide_scan_pcidev(dev);
+ else
+ while ((dev = pci_get_device_reverse(PCI_ANY_ID, PCI_ANY_ID,
+ dev)))
+ ide_scan_pcidev(dev);
+
+ /*
+ * Hand the drivers over to the PCI layer now we
+ * are post init.
+ */
+
+ list_for_each_safe(l, n, &ide_pci_drivers) {
+ list_del(l);
+ d = list_entry(l, struct pci_driver, node);
+ if (__pci_register_driver(d, d->driver.owner,
+ d->driver.mod_name))
+ printk(KERN_ERR "%s: failed to register %s driver\n",
+ __FUNCTION__, d->driver.mod_name);
+ }
+
+ return 0;
+}
+
+static int __init ide_scan_pci(void)
+{
+ return ide_scan_pcibus();
+}
+
+module_init(ide_scan_pci);
diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c
index 3cbca3f..d71a584 100644
--- a/drivers/ide/ide-tape.c
+++ b/drivers/ide/ide-tape.c
@@ -1690,6 +1690,11 @@
if (error)
tape->failed_pc = NULL;
+ if (!blk_special_request(rq)) {
+ ide_end_request(drive, uptodate, nr_sects);
+ return 0;
+ }
+
spin_lock_irqsave(&tape->spinlock, flags);
/* The request was a pipelined data transfer request */
diff --git a/drivers/ide/ide-taskfile.c b/drivers/ide/ide-taskfile.c
index 2d63ea9..5eb6fa1 100644
--- a/drivers/ide/ide-taskfile.c
+++ b/drivers/ide/ide-taskfile.c
@@ -35,34 +35,6 @@
#include <asm/uaccess.h>
#include <asm/io.h>
-static void ata_bswap_data (void *buffer, int wcount)
-{
- u16 *p = buffer;
-
- while (wcount--) {
- *p = *p << 8 | *p >> 8; p++;
- *p = *p << 8 | *p >> 8; p++;
- }
-}
-
-static void taskfile_input_data(ide_drive_t *drive, void *buffer, u32 wcount)
-{
- HWIF(drive)->ata_input_data(drive, buffer, wcount);
- if (drive->bswap)
- ata_bswap_data(buffer, wcount);
-}
-
-static void taskfile_output_data(ide_drive_t *drive, void *buffer, u32 wcount)
-{
- if (drive->bswap) {
- ata_bswap_data(buffer, wcount);
- HWIF(drive)->ata_output_data(drive, buffer, wcount);
- ata_bswap_data(buffer, wcount);
- } else {
- HWIF(drive)->ata_output_data(drive, buffer, wcount);
- }
-}
-
void ide_tf_load(ide_drive_t *drive, ide_task_t *task)
{
ide_hwif_t *hwif = drive->hwif;
@@ -77,10 +49,13 @@
"lbam 0x%02x lbah 0x%02x dev 0x%02x cmd 0x%02x\n",
drive->name, tf->feature, tf->nsect, tf->lbal,
tf->lbam, tf->lbah, tf->device, tf->command);
+ printk("%s: hob: nsect 0x%02x lbal 0x%02x "
+ "lbam 0x%02x lbah 0x%02x\n",
+ drive->name, tf->hob_nsect, tf->hob_lbal,
+ tf->hob_lbam, tf->hob_lbah);
#endif
- if (IDE_CONTROL_REG)
- hwif->OUTB(drive->ctl, IDE_CONTROL_REG); /* clear nIEN */
+ ide_set_irq(drive, 1);
if ((task->tf_flags & IDE_TFLAG_NO_SELECT_MASK) == 0)
SELECT_MASK(drive, 0);
@@ -124,7 +99,7 @@
args.tf.command = WIN_IDENTIFY;
else
args.tf.command = WIN_PIDENTIFY;
- args.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
+ args.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
args.data_phase = TASKFILE_IN;
return ide_raw_taskfile(drive, &args, buf, 1);
}
@@ -285,7 +260,7 @@
return ide_stopped;
}
-static u8 wait_drive_not_busy(ide_drive_t *drive)
+u8 wait_drive_not_busy(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
int retries;
@@ -293,8 +268,7 @@
/*
* Last sector was transfered, wait until drive is ready.
- * This can take up to 10 usec, but we will wait max 1 ms
- * (drive_cmd_intr() waits that long).
+ * This can take up to 10 usec, but we will wait max 1 ms.
*/
for (retries = 0; retries < 100; retries++) {
if ((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT)
@@ -349,9 +323,9 @@
/* do the actual data transfer */
if (write)
- taskfile_output_data(drive, buf, SECTOR_WORDS);
+ hwif->ata_output_data(drive, buf, SECTOR_WORDS);
else
- taskfile_input_data(drive, buf, SECTOR_WORDS);
+ hwif->ata_input_data(drive, buf, SECTOR_WORDS);
kunmap_atomic(buf, KM_BIO_SRC_IRQ);
#ifdef CONFIG_HIGHMEM
@@ -371,9 +345,18 @@
static void ide_pio_datablock(ide_drive_t *drive, struct request *rq,
unsigned int write)
{
+ u8 saved_io_32bit = drive->io_32bit;
+
if (rq->bio) /* fs request */
rq->errors = 0;
+ if (rq->cmd_type == REQ_TYPE_ATA_TASKFILE) {
+ ide_task_t *task = rq->special;
+
+ if (task->tf_flags & IDE_TFLAG_IO_16BIT)
+ drive->io_32bit = 0;
+ }
+
touch_softlockup_watchdog();
switch (drive->hwif->data_phase) {
@@ -385,6 +368,8 @@
ide_pio_sector(drive, write);
break;
}
+
+ drive->io_32bit = saved_io_32bit;
}
static ide_startstop_t task_error(ide_drive_t *drive, struct request *rq,
@@ -422,27 +407,22 @@
return ide_error(drive, s, stat);
}
-static void task_end_request(ide_drive_t *drive, struct request *rq, u8 stat)
+void task_end_request(ide_drive_t *drive, struct request *rq, u8 stat)
{
- HWIF(drive)->cursg = NULL;
-
if (rq->cmd_type == REQ_TYPE_ATA_TASKFILE) {
- ide_task_t *task = rq->special;
+ u8 err = drive->hwif->INB(IDE_ERROR_REG);
- if (task->tf_flags & IDE_TFLAG_FLAGGED) {
- u8 err = drive->hwif->INB(IDE_ERROR_REG);
- ide_end_drive_cmd(drive, stat, err);
- return;
- }
+ ide_end_drive_cmd(drive, stat, err);
+ return;
}
if (rq->rq_disk) {
ide_driver_t *drv;
drv = *(ide_driver_t **)rq->rq_disk->private_data;;
- drv->end_request(drive, 1, rq->hard_nr_sectors);
+ drv->end_request(drive, 1, rq->nr_sectors);
} else
- ide_end_request(drive, 1, rq->hard_nr_sectors);
+ ide_end_request(drive, 1, rq->nr_sectors);
}
/*
@@ -455,7 +435,7 @@
u8 stat = hwif->INB(IDE_STATUS_REG);
/* new way for dealing with premature shared PCI interrupts */
- if (!OK_STAT(stat, DATA_READY, BAD_R_STAT)) {
+ if (!OK_STAT(stat, DRQ_STAT, BAD_R_STAT)) {
if (stat & (ERR_STAT | DRQ_STAT))
return task_error(drive, rq, __FUNCTION__, stat);
/* No data yet, so wait for another IRQ. */
@@ -468,7 +448,7 @@
/* If it was the last datablock check status and finish transfer. */
if (!hwif->nleft) {
stat = wait_drive_not_busy(drive);
- if (!OK_STAT(stat, 0, BAD_R_STAT))
+ if (!OK_STAT(stat, 0, BAD_STAT))
return task_error(drive, rq, __FUNCTION__, stat);
task_end_request(drive, rq, stat);
return ide_stopped;
@@ -512,7 +492,7 @@
{
ide_startstop_t startstop;
- if (ide_wait_stat(&startstop, drive, DATA_READY,
+ if (ide_wait_stat(&startstop, drive, DRQ_STAT,
drive->bad_wstat, WAIT_DRQ)) {
printk(KERN_ERR "%s: no DRQ after issuing %sWRITE%s\n",
drive->name,
@@ -580,7 +560,6 @@
unsigned int taskin = 0;
unsigned int taskout = 0;
u16 nsect = 0;
- u8 io_32bit = drive->io_32bit;
char __user *buf = (char __user *)arg;
// printk("IDE Taskfile ...\n");
@@ -633,9 +612,10 @@
args.data_phase = req_task->data_phase;
- args.tf_flags = IDE_TFLAG_OUT_DEVICE;
+ args.tf_flags = IDE_TFLAG_IO_16BIT | IDE_TFLAG_DEVICE |
+ IDE_TFLAG_IN_TF;
if (drive->addressing == 1)
- args.tf_flags |= IDE_TFLAG_LBA48;
+ args.tf_flags |= (IDE_TFLAG_LBA48 | IDE_TFLAG_IN_HOB);
if (req_task->out_flags.all) {
args.tf_flags |= IDE_TFLAG_FLAGGED;
@@ -671,7 +651,6 @@
if (req_task->in_flags.b.data)
args.tf_flags |= IDE_TFLAG_IN_DATA;
- drive->io_32bit = 0;
switch(req_task->data_phase) {
case TASKFILE_MULTI_OUT:
if (!drive->mult_count) {
@@ -767,41 +746,24 @@
// printk("IDE Taskfile ioctl ended. rc = %i\n", err);
- drive->io_32bit = io_32bit;
-
return err;
}
#endif
-int ide_wait_cmd (ide_drive_t *drive, u8 cmd, u8 nsect, u8 feature, u8 sectors, u8 *buf)
-{
- struct request rq;
- u8 buffer[4];
-
- if (!buf)
- buf = buffer;
- memset(buf, 0, 4 + SECTOR_WORDS * 4 * sectors);
- ide_init_drive_cmd(&rq);
- rq.buffer = buf;
- *buf++ = cmd;
- *buf++ = nsect;
- *buf++ = feature;
- *buf++ = sectors;
- return ide_do_drive_cmd(drive, &rq, ide_wait);
-}
-
int ide_cmd_ioctl (ide_drive_t *drive, unsigned int cmd, unsigned long arg)
{
- int err = 0;
- u8 args[4], *argbuf = args;
- u8 xfer_rate = 0;
- int argsize = 4;
+ u8 *buf = NULL;
+ int bufsize = 0, err = 0;
+ u8 args[4], xfer_rate = 0;
ide_task_t tfargs;
struct ide_taskfile *tf = &tfargs.tf;
if (NULL == (void *) arg) {
struct request rq;
+
ide_init_drive_cmd(&rq);
+ rq.cmd_type = REQ_TYPE_ATA_TASKFILE;
+
return ide_do_drive_cmd(drive, &rq, ide_wait);
}
@@ -810,23 +772,39 @@
memset(&tfargs, 0, sizeof(ide_task_t));
tf->feature = args[2];
- tf->nsect = args[3];
- tf->lbal = args[1];
+ if (args[0] == WIN_SMART) {
+ tf->nsect = args[3];
+ tf->lbal = args[1];
+ tf->lbam = 0x4f;
+ tf->lbah = 0xc2;
+ tfargs.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_IN_NSECT;
+ } else {
+ tf->nsect = args[1];
+ tfargs.tf_flags = IDE_TFLAG_OUT_FEATURE |
+ IDE_TFLAG_OUT_NSECT | IDE_TFLAG_IN_NSECT;
+ }
tf->command = args[0];
+ tfargs.data_phase = args[3] ? TASKFILE_IN : TASKFILE_NO_DATA;
if (args[3]) {
- argsize = 4 + (SECTOR_WORDS * 4 * args[3]);
- argbuf = kzalloc(argsize, GFP_KERNEL);
- if (argbuf == NULL)
+ tfargs.tf_flags |= IDE_TFLAG_IO_16BIT;
+ bufsize = SECTOR_WORDS * 4 * args[3];
+ buf = kzalloc(bufsize, GFP_KERNEL);
+ if (buf == NULL)
return -ENOMEM;
}
+
if (set_transfer(drive, &tfargs)) {
xfer_rate = args[1];
if (ide_ata66_check(drive, &tfargs))
goto abort;
}
- err = ide_wait_cmd(drive, args[0], args[1], args[2], args[3], argbuf);
+ err = ide_raw_taskfile(drive, &tfargs, buf, args[3]);
+
+ args[0] = tf->status;
+ args[1] = tf->error;
+ args[2] = tf->nsect;
if (!err && xfer_rate) {
/* active-retuning-calls future */
@@ -834,10 +812,13 @@
ide_driveid_update(drive);
}
abort:
- if (copy_to_user((void __user *)arg, argbuf, argsize))
+ if (copy_to_user((void __user *)arg, &args, 4))
err = -EFAULT;
- if (argsize > 4)
- kfree(argbuf);
+ if (buf) {
+ if (copy_to_user((void __user *)(arg + 4), buf, bufsize))
+ err = -EFAULT;
+ kfree(buf);
+ }
return err;
}
@@ -854,7 +835,7 @@
memset(&task, 0, sizeof(task));
memcpy(&task.tf_array[7], &args[1], 6);
task.tf.command = args[0];
- task.tf_flags = IDE_TFLAG_OUT_TF | IDE_TFLAG_OUT_DEVICE;
+ task.tf_flags = IDE_TFLAG_TF | IDE_TFLAG_DEVICE;
err = ide_no_data_taskfile(drive, &task);
diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c
index c6d4f63..97894ab 100644
--- a/drivers/ide/ide.c
+++ b/drivers/ide/ide.c
@@ -95,7 +95,7 @@
__cacheline_aligned_in_smp DEFINE_SPINLOCK(ide_lock);
#ifdef CONFIG_IDEPCI_PCIBUS_ORDER
-static int ide_scan_direction; /* THIS was formerly 2.2.x pci=reverse */
+int ide_scan_direction; /* THIS was formerly 2.2.x pci=reverse */
#endif
int noautodma = 0;
@@ -116,7 +116,7 @@
/*
* Do not even *think* about calling this!
*/
-static void init_hwif_data(ide_hwif_t *hwif, unsigned int index)
+void ide_init_port_data(ide_hwif_t *hwif, unsigned int index)
{
unsigned int unit;
@@ -159,6 +159,7 @@
init_completion(&drive->gendev_rel_comp);
}
}
+EXPORT_SYMBOL_GPL(ide_init_port_data);
static void init_hwif_default(ide_hwif_t *hwif, unsigned int index)
{
@@ -177,8 +178,6 @@
#endif
}
-extern void ide_arm_init(void);
-
/*
* init_ide_data() sets reasonable default values into all fields
* of all instances of the hwifs and drives, but only on the first call.
@@ -210,16 +209,13 @@
/* Initialise all interface structures */
for (index = 0; index < MAX_HWIFS; ++index) {
hwif = &ide_hwifs[index];
- init_hwif_data(hwif, index);
+ ide_init_port_data(hwif, index);
init_hwif_default(hwif, index);
#if !defined(CONFIG_PPC32) || !defined(CONFIG_PCI)
hwif->irq =
ide_init_default_irq(hwif->io_ports[IDE_DATA_OFFSET]);
#endif
}
-#ifdef CONFIG_IDE_ARM
- ide_arm_init();
-#endif
}
/**
@@ -414,8 +410,6 @@
hwif->cds = tmp_hwif->cds;
#endif
- hwif->fixup = tmp_hwif->fixup;
-
hwif->set_pio_mode = tmp_hwif->set_pio_mode;
hwif->set_dma_mode = tmp_hwif->set_dma_mode;
hwif->mdma_filter = tmp_hwif->mdma_filter;
@@ -433,16 +427,13 @@
hwif->atapi_input_bytes = tmp_hwif->atapi_input_bytes;
hwif->atapi_output_bytes = tmp_hwif->atapi_output_bytes;
+ hwif->dma_host_set = tmp_hwif->dma_host_set;
hwif->dma_setup = tmp_hwif->dma_setup;
hwif->dma_exec_cmd = tmp_hwif->dma_exec_cmd;
hwif->dma_start = tmp_hwif->dma_start;
hwif->ide_dma_end = tmp_hwif->ide_dma_end;
- hwif->ide_dma_on = tmp_hwif->ide_dma_on;
- hwif->dma_off_quietly = tmp_hwif->dma_off_quietly;
hwif->ide_dma_test_irq = tmp_hwif->ide_dma_test_irq;
hwif->ide_dma_clear_irq = tmp_hwif->ide_dma_clear_irq;
- hwif->dma_host_on = tmp_hwif->dma_host_on;
- hwif->dma_host_off = tmp_hwif->dma_host_off;
hwif->dma_lost_irq = tmp_hwif->dma_lost_irq;
hwif->dma_timeout = tmp_hwif->dma_timeout;
@@ -614,7 +605,7 @@
tmp_hwif = *hwif;
/* restore hwif data to pristine status */
- init_hwif_data(hwif, index);
+ ide_init_port_data(hwif, index);
init_hwif_default(hwif, index);
ide_hwif_restore(hwif, &tmp_hwif);
@@ -680,24 +671,34 @@
*/
}
+void ide_init_port_hw(ide_hwif_t *hwif, hw_regs_t *hw)
+{
+ memcpy(hwif->io_ports, hw->io_ports, sizeof(hwif->io_ports));
+ hwif->irq = hw->irq;
+ hwif->noprobe = 0;
+ hwif->chipset = hw->chipset;
+ hwif->gendev.parent = hw->dev;
+ hwif->ack_intr = hw->ack_intr;
+}
+EXPORT_SYMBOL_GPL(ide_init_port_hw);
+
/**
* ide_register_hw - register IDE interface
* @hw: hardware registers
- * @fixup: fixup function
- * @initializing: set while initializing built-in drivers
+ * @quirkproc: quirkproc function
* @hwifp: pointer to returned hwif
*
* Register an IDE interface, specifying exactly the registers etc.
- * Set init=1 iff calling before probes have taken place.
*
* Returns -1 on error.
*/
-int ide_register_hw(hw_regs_t *hw, void (*fixup)(ide_hwif_t *),
- int initializing, ide_hwif_t **hwifp)
+int ide_register_hw(hw_regs_t *hw, void (*quirkproc)(ide_drive_t *),
+ ide_hwif_t **hwifp)
{
int index, retry = 1;
ide_hwif_t *hwif;
+ u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
do {
for (index = 0; index < MAX_HWIFS; ++index) {
@@ -709,8 +710,7 @@
hwif = &ide_hwifs[index];
if (hwif->hold)
continue;
- if ((!hwif->present && !hwif->mate && !initializing) ||
- (!hwif->io_ports[IDE_DATA_OFFSET] && initializing))
+ if (!hwif->present && hwif->mate == NULL)
goto found;
}
for (index = 0; index < MAX_HWIFS; index++)
@@ -721,29 +721,23 @@
if (hwif->present)
ide_unregister(index);
else if (!hwif->hold) {
- init_hwif_data(hwif, index);
+ ide_init_port_data(hwif, index);
init_hwif_default(hwif, index);
}
if (hwif->present)
return -1;
- memcpy(hwif->io_ports, hw->io_ports, sizeof(hwif->io_ports));
- hwif->irq = hw->irq;
- hwif->noprobe = 0;
- hwif->fixup = fixup;
- hwif->chipset = hw->chipset;
- hwif->gendev.parent = hw->dev;
- hwif->ack_intr = hw->ack_intr;
- if (initializing == 0) {
- u8 idx[4] = { index, 0xff, 0xff, 0xff };
+ ide_init_port_hw(hwif, hw);
+ hwif->quirkproc = quirkproc;
- ide_device_add(idx);
- }
+ idx[0] = index;
+
+ ide_device_add(idx);
if (hwifp)
*hwifp = hwif;
- return (initializing || hwif->present) ? index : -1;
+ return hwif->present ? index : -1;
}
EXPORT_SYMBOL(ide_register_hw);
@@ -836,7 +830,7 @@
if (!drive->id || !(drive->id->capability & 1))
goto out;
- if (hwif->ide_dma_on == NULL)
+ if (hwif->dma_host_set == NULL)
goto out;
err = -EBUSY;
@@ -884,7 +878,10 @@
if (drive->special.b.set_tune)
return -EBUSY;
+
ide_init_drive_cmd(&rq);
+ rq.cmd_type = REQ_TYPE_ATA_TASKFILE;
+
drive->tune_req = (u8) arg;
drive->special.b.set_tune = 1;
(void) ide_do_drive_cmd(drive, &rq, ide_wait);
@@ -1066,7 +1063,7 @@
ide_init_hwif_ports(&hw, (unsigned long) args[0],
(unsigned long) args[1], NULL);
hw.irq = args[2];
- if (ide_register_hw(&hw, NULL, 0, NULL) == -1)
+ if (ide_register_hw(&hw, NULL, NULL) == -1)
return -EIO;
return 0;
}
@@ -1227,26 +1224,12 @@
return 0; /* zero = nothing matched */
}
-#ifdef CONFIG_BLK_DEV_ALI14XX
extern int probe_ali14xx;
-extern int ali14xx_init(void);
-#endif
-#ifdef CONFIG_BLK_DEV_UMC8672
extern int probe_umc8672;
-extern int umc8672_init(void);
-#endif
-#ifdef CONFIG_BLK_DEV_DTC2278
extern int probe_dtc2278;
-extern int dtc2278_init(void);
-#endif
-#ifdef CONFIG_BLK_DEV_HT6560B
extern int probe_ht6560b;
-extern int ht6560b_init(void);
-#endif
-#ifdef CONFIG_BLK_DEV_QD65XX
extern int probe_qd65xx;
-extern int qd65xx_init(void);
-#endif
+extern int cmd640_vlb;
static int __initdata is_chipset_set[MAX_HWIFS];
@@ -1323,7 +1306,7 @@
if (s[0] == 'h' && s[1] == 'd' && s[2] >= 'a' && s[2] <= max_drive) {
const char *hd_words[] = {
"none", "noprobe", "nowerr", "cdrom", "nodma",
- "autotune", "noautotune", "minus8", "swapdata", "bswap",
+ "autotune", "noautotune", "-8", "-9", "-10",
"noflush", "remap", "remap63", "scsi", NULL };
unit = s[2] - 'a';
hw = unit / MAX_DRIVES;
@@ -1359,10 +1342,6 @@
case -7: /* "noautotune" */
drive->autotune = IDE_TUNE_NOAUTO;
goto obsolete_option;
- case -9: /* "swapdata" */
- case -10: /* "bswap" */
- drive->bswap = 1;
- goto done;
case -11: /* noflush */
drive->noflush = 1;
goto done;
@@ -1462,11 +1441,8 @@
#endif
#ifdef CONFIG_BLK_DEV_CMD640
case -14: /* "cmd640_vlb" */
- {
- extern int cmd640_vlb; /* flag for cmd640.c */
cmd640_vlb = 1;
goto done;
- }
#endif
#ifdef CONFIG_BLK_DEV_HT6560B
case -13: /* "ht6560b" */
@@ -1556,79 +1532,6 @@
return 1;
}
-extern void __init pnpide_init(void);
-extern void __exit pnpide_exit(void);
-extern void __init h8300_ide_init(void);
-
-/*
- * probe_for_hwifs() finds/initializes "known" IDE interfaces
- */
-static void __init probe_for_hwifs (void)
-{
-#ifdef CONFIG_IDEPCI_PCIBUS_ORDER
- ide_scan_pcibus(ide_scan_direction);
-#endif
-
-#ifdef CONFIG_ETRAX_IDE
- {
- extern void init_e100_ide(void);
- init_e100_ide();
- }
-#endif /* CONFIG_ETRAX_IDE */
-#ifdef CONFIG_BLK_DEV_CMD640
- {
- extern void ide_probe_for_cmd640x(void);
- ide_probe_for_cmd640x();
- }
-#endif /* CONFIG_BLK_DEV_CMD640 */
-#ifdef CONFIG_BLK_DEV_IDE_PMAC
- {
- extern int pmac_ide_probe(void);
- (void)pmac_ide_probe();
- }
-#endif /* CONFIG_BLK_DEV_IDE_PMAC */
-#ifdef CONFIG_BLK_DEV_GAYLE
- {
- extern void gayle_init(void);
- gayle_init();
- }
-#endif /* CONFIG_BLK_DEV_GAYLE */
-#ifdef CONFIG_BLK_DEV_FALCON_IDE
- {
- extern void falconide_init(void);
- falconide_init();
- }
-#endif /* CONFIG_BLK_DEV_FALCON_IDE */
-#ifdef CONFIG_BLK_DEV_MAC_IDE
- {
- extern void macide_init(void);
- macide_init();
- }
-#endif /* CONFIG_BLK_DEV_MAC_IDE */
-#ifdef CONFIG_BLK_DEV_Q40IDE
- {
- extern void q40ide_init(void);
- q40ide_init();
- }
-#endif /* CONFIG_BLK_DEV_Q40IDE */
-#ifdef CONFIG_BLK_DEV_BUDDHA
- {
- extern void buddha_init(void);
- buddha_init();
- }
-#endif /* CONFIG_BLK_DEV_BUDDHA */
-#ifdef CONFIG_BLK_DEV_IDEPNP
- pnpide_init();
-#endif
-#ifdef CONFIG_H8300
- h8300_ide_init();
-#endif
-}
-
-/*
- * Probe module
- */
-
EXPORT_SYMBOL(ide_lock);
static int ide_bus_match(struct device *dev, struct device_driver *drv)
@@ -1775,30 +1678,6 @@
proc_ide_create();
-#ifdef CONFIG_BLK_DEV_ALI14XX
- if (probe_ali14xx)
- (void)ali14xx_init();
-#endif
-#ifdef CONFIG_BLK_DEV_UMC8672
- if (probe_umc8672)
- (void)umc8672_init();
-#endif
-#ifdef CONFIG_BLK_DEV_DTC2278
- if (probe_dtc2278)
- (void)dtc2278_init();
-#endif
-#ifdef CONFIG_BLK_DEV_HT6560B
- if (probe_ht6560b)
- (void)ht6560b_init();
-#endif
-#ifdef CONFIG_BLK_DEV_QD65XX
- if (probe_qd65xx)
- (void)qd65xx_init();
-#endif
-
- /* Probe for special PCI and other "known" interface chipsets. */
- probe_for_hwifs();
-
return 0;
}
@@ -1834,10 +1713,6 @@
for (index = 0; index < MAX_HWIFS; ++index)
ide_unregister(index);
-#ifdef CONFIG_BLK_DEV_IDEPNP
- pnpide_exit();
-#endif
-
proc_ide_destroy();
bus_unregister(&ide_bus_type);
diff --git a/drivers/ide/legacy/Makefile b/drivers/ide/legacy/Makefile
index 4098223..7043ec7 100644
--- a/drivers/ide/legacy/Makefile
+++ b/drivers/ide/legacy/Makefile
@@ -1,15 +1,24 @@
+# link order is important here
+
obj-$(CONFIG_BLK_DEV_ALI14XX) += ali14xx.o
+obj-$(CONFIG_BLK_DEV_UMC8672) += umc8672.o
obj-$(CONFIG_BLK_DEV_DTC2278) += dtc2278.o
obj-$(CONFIG_BLK_DEV_HT6560B) += ht6560b.o
obj-$(CONFIG_BLK_DEV_QD65XX) += qd65xx.o
-obj-$(CONFIG_BLK_DEV_UMC8672) += umc8672.o
-obj-$(CONFIG_BLK_DEV_IDECS) += ide-cs.o
+obj-$(CONFIG_BLK_DEV_GAYLE) += gayle.o
+obj-$(CONFIG_BLK_DEV_FALCON_IDE) += falconide.o
+obj-$(CONFIG_BLK_DEV_MAC_IDE) += macide.o
+obj-$(CONFIG_BLK_DEV_Q40IDE) += q40ide.o
+obj-$(CONFIG_BLK_DEV_BUDDHA) += buddha.o
-obj-$(CONFIG_BLK_DEV_PLATFORM) += ide_platform.o
+ifeq ($(CONFIG_BLK_DEV_IDECS), m)
+ obj-m += ide-cs.o
+endif
-# Last of all
-obj-$(CONFIG_BLK_DEV_HD) += hd.o
+ifeq ($(CONFIG_BLK_DEV_PLATFORM), m)
+ obj-m += ide_platform.o
+endif
EXTRA_CFLAGS := -Idrivers/ide
diff --git a/drivers/ide/legacy/ali14xx.c b/drivers/ide/legacy/ali14xx.c
index 38c3a6d..5ec0be4 100644
--- a/drivers/ide/legacy/ali14xx.c
+++ b/drivers/ide/legacy/ali14xx.c
@@ -231,8 +231,7 @@
module_param_named(probe, probe_ali14xx, bool, 0);
MODULE_PARM_DESC(probe, "probe for ALI M14xx chipsets");
-/* Can be called directly from ide.c. */
-int __init ali14xx_init(void)
+static int __init ali14xx_init(void)
{
if (probe_ali14xx == 0)
goto out;
@@ -248,9 +247,7 @@
return -ENODEV;
}
-#ifdef MODULE
module_init(ali14xx_init);
-#endif
MODULE_AUTHOR("see local file");
MODULE_DESCRIPTION("support of ALI 14XX IDE chipsets");
diff --git a/drivers/ide/legacy/buddha.c b/drivers/ide/legacy/buddha.c
index 4a0be25..74d28e0 100644
--- a/drivers/ide/legacy/buddha.c
+++ b/drivers/ide/legacy/buddha.c
@@ -112,6 +112,7 @@
BOARD_BUDDHA, BOARD_CATWEASEL, BOARD_XSURF
} BuddhaType;
+static const char *buddha_board_name[] = { "Buddha", "Catweasel", "X-Surf" };
/*
* Check and acknowledge the interrupt status
@@ -143,11 +144,11 @@
* Probe for a Buddha or Catweasel IDE interface
*/
-void __init buddha_init(void)
+static int __init buddha_init(void)
{
hw_regs_t hw;
ide_hwif_t *hwif;
- int i, index;
+ int i;
struct zorro_dev *z = NULL;
u_long buddha_board = 0;
@@ -156,6 +157,8 @@
while ((z = zorro_find_device(ZORRO_WILDCARD, z))) {
unsigned long board;
+ u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
+
if (z->id == ZORRO_PROD_INDIVIDUAL_COMPUTERS_BUDDHA) {
buddha_num_hwifs = BUDDHA_NUM_HWIFS;
type=BOARD_BUDDHA;
@@ -195,7 +198,10 @@
/* X-Surf doesn't have this. IRQs are always on */
if (type != BOARD_XSURF)
z_writeb(0, buddha_board+BUDDHA_IRQ_MR);
-
+
+ printk(KERN_INFO "ide: %s IDE controller\n",
+ buddha_board_name[type]);
+
for(i=0;i<buddha_num_hwifs;i++) {
if(type != BOARD_XSURF) {
ide_setup_ports(&hw, (buddha_board+buddha_bases[i]),
@@ -213,23 +219,23 @@
IRQ_AMIGA_PORTS);
}
- index = ide_register_hw(&hw, NULL, 1, &hwif);
- if (index != -1) {
+ hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
+ if (hwif) {
+ u8 index = hwif->index;
+
+ ide_init_port_data(hwif, index);
+ ide_init_port_hw(hwif, &hw);
+
hwif->mmio = 1;
- printk("ide%d: ", index);
- switch(type) {
- case BOARD_BUDDHA:
- printk("Buddha");
- break;
- case BOARD_CATWEASEL:
- printk("Catweasel");
- break;
- case BOARD_XSURF:
- printk("X-Surf");
- break;
- }
- printk(" IDE interface\n");
- }
+
+ idx[i] = index;
+ }
}
+
+ ide_device_add(idx);
}
+
+ return 0;
}
+
+module_init(buddha_init);
diff --git a/drivers/ide/legacy/dtc2278.c b/drivers/ide/legacy/dtc2278.c
index 24a845d..13eee6d 100644
--- a/drivers/ide/legacy/dtc2278.c
+++ b/drivers/ide/legacy/dtc2278.c
@@ -150,8 +150,7 @@
module_param_named(probe, probe_dtc2278, bool, 0);
MODULE_PARM_DESC(probe, "probe for DTC2278xx chipsets");
-/* Can be called directly from ide.c. */
-int __init dtc2278_init(void)
+static int __init dtc2278_init(void)
{
if (probe_dtc2278 == 0)
return -ENODEV;
@@ -163,9 +162,7 @@
return 0;
}
-#ifdef MODULE
module_init(dtc2278_init);
-#endif
MODULE_AUTHOR("See Local File");
MODULE_DESCRIPTION("support of DTC-2278 VLB IDE chipsets");
diff --git a/drivers/ide/legacy/falconide.c b/drivers/ide/legacy/falconide.c
index 7d7936f..2860956 100644
--- a/drivers/ide/legacy/falconide.c
+++ b/drivers/ide/legacy/falconide.c
@@ -62,19 +62,31 @@
* Probe for a Falcon IDE interface
*/
-void __init falconide_init(void)
+static int __init falconide_init(void)
{
if (MACH_IS_ATARI && ATARIHW_PRESENT(IDE)) {
hw_regs_t hw;
- int index;
+
+ printk(KERN_INFO "ide: Falcon IDE controller\n");
ide_setup_ports(&hw, ATA_HD_BASE, falconide_offsets,
0, 0, NULL,
// falconide_iops,
IRQ_MFP_IDE);
- index = ide_register_hw(&hw, NULL, 1, NULL);
- if (index != -1)
- printk("ide%d: Falcon IDE interface\n", index);
+ hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
+ if (hwif) {
+ u8 index = hwif->index;
+ u8 idx[4] = { index, 0xff, 0xff, 0xff };
+
+ ide_init_port_data(hwif, index);
+ ide_init_port_hw(hwif, &hw);
+
+ ide_device_add(idx);
+ }
}
+
+ return 0;
}
+
+module_init(falconide_init);
diff --git a/drivers/ide/legacy/gayle.c b/drivers/ide/legacy/gayle.c
index 53331ee..492fa04 100644
--- a/drivers/ide/legacy/gayle.c
+++ b/drivers/ide/legacy/gayle.c
@@ -110,12 +110,13 @@
* Probe for a Gayle IDE interface (and optionally for an IDE doubler)
*/
-void __init gayle_init(void)
+static int __init gayle_init(void)
{
int a4000, i;
+ u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
if (!MACH_IS_AMIGA)
- return;
+ return -ENODEV;
if ((a4000 = AMIGAHW_PRESENT(A4000_IDE)) || AMIGAHW_PRESENT(A1200_IDE))
goto found;
@@ -125,15 +126,21 @@
NULL))
goto found;
#endif
- return;
+ return -ENODEV;
found:
+ printk(KERN_INFO "ide: Gayle IDE controller (A%d style%s)\n",
+ a4000 ? 4000 : 1200,
+#ifdef CONFIG_BLK_DEV_IDEDOUBLER
+ ide_doubler ? ", IDE doubler" :
+#endif
+ "");
+
for (i = 0; i < GAYLE_NUM_PROBE_HWIFS; i++) {
unsigned long base, ctrlport, irqport;
ide_ack_intr_t *ack_intr;
hw_regs_t hw;
ide_hwif_t *hwif;
- int index;
unsigned long phys_base, res_start, res_n;
if (a4000) {
@@ -165,21 +172,23 @@
// &gayle_iops,
IRQ_AMIGA_PORTS);
- index = ide_register_hw(&hw, NULL, 1, &hwif);
- if (index != -1) {
+ hwif = ide_find_port(base);
+ if (hwif) {
+ u8 index = hwif->index;
+
+ ide_init_port_data(hwif, index);
+ ide_init_port_hw(hwif, &hw);
+
hwif->mmio = 1;
- switch (i) {
- case 0:
- printk("ide%d: Gayle IDE interface (A%d style)\n", index,
- a4000 ? 4000 : 1200);
- break;
-#ifdef CONFIG_BLK_DEV_IDEDOUBLER
- case 1:
- printk("ide%d: IDE doubler\n", index);
- break;
-#endif /* CONFIG_BLK_DEV_IDEDOUBLER */
- }
+
+ idx[i] = index;
} else
release_mem_region(res_start, res_n);
}
+
+ ide_device_add(idx);
+
+ return 0;
}
+
+module_init(gayle_init);
diff --git a/drivers/ide/legacy/ht6560b.c b/drivers/ide/legacy/ht6560b.c
index a4245d1..8da5031 100644
--- a/drivers/ide/legacy/ht6560b.c
+++ b/drivers/ide/legacy/ht6560b.c
@@ -307,8 +307,7 @@
module_param_named(probe, probe_ht6560b, bool, 0);
MODULE_PARM_DESC(probe, "probe for HT6560B chipset");
-/* Can be called directly from ide.c. */
-int __init ht6560b_init(void)
+static int __init ht6560b_init(void)
{
ide_hwif_t *hwif, *mate;
static u8 idx[4] = { 0, 1, 0xff, 0xff };
@@ -369,9 +368,7 @@
return -ENODEV;
}
-#ifdef MODULE
module_init(ht6560b_init);
-#endif
MODULE_AUTHOR("See Local File");
MODULE_DESCRIPTION("HT-6560B EIDE-controller support");
diff --git a/drivers/ide/legacy/ide-cs.c b/drivers/ide/legacy/ide-cs.c
index 03715c0..f4ea15b 100644
--- a/drivers/ide/legacy/ide-cs.c
+++ b/drivers/ide/legacy/ide-cs.c
@@ -153,7 +153,7 @@
hw.irq = irq;
hw.chipset = ide_pci;
hw.dev = &handle->dev;
- return ide_register_hw(&hw, &ide_undecoded_slave, 0, NULL);
+ return ide_register_hw(&hw, &ide_undecoded_slave, NULL);
}
/*======================================================================
diff --git a/drivers/ide/legacy/ide_platform.c b/drivers/ide/legacy/ide_platform.c
index 7bb79f5..69a0fb0 100644
--- a/drivers/ide/legacy/ide_platform.c
+++ b/drivers/ide/legacy/ide_platform.c
@@ -28,39 +28,27 @@
int index;
} hwif_prop;
-static ide_hwif_t *__devinit plat_ide_locate_hwif(void __iomem *base,
- void __iomem *ctrl, struct pata_platform_info *pdata, int irq,
- int mmio)
+static void __devinit plat_ide_setup_ports(hw_regs_t *hw,
+ void __iomem *base,
+ void __iomem *ctrl,
+ struct pata_platform_info *pdata,
+ int irq)
{
unsigned long port = (unsigned long)base;
- ide_hwif_t *hwif = ide_find_port(port);
int i;
- if (hwif == NULL)
- goto out;
-
- hwif->io_ports[IDE_DATA_OFFSET] = port;
+ hw->io_ports[IDE_DATA_OFFSET] = port;
port += (1 << pdata->ioport_shift);
for (i = IDE_ERROR_OFFSET; i <= IDE_STATUS_OFFSET;
i++, port += (1 << pdata->ioport_shift))
- hwif->io_ports[i] = port;
+ hw->io_ports[i] = port;
- hwif->io_ports[IDE_CONTROL_OFFSET] = (unsigned long)ctrl;
+ hw->io_ports[IDE_CONTROL_OFFSET] = (unsigned long)ctrl;
- hwif->irq = irq;
+ hw->irq = irq;
- hwif->chipset = ide_generic;
-
- if (mmio) {
- hwif->mmio = 1;
- default_hwif_mmiops(hwif);
- }
-
- hwif_prop.hwif = hwif;
- hwif_prop.index = hwif->index;
-out:
- return hwif;
+ hw->chipset = ide_generic;
}
static int __devinit plat_ide_probe(struct platform_device *pdev)
@@ -71,6 +59,7 @@
u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
int ret = 0;
int mmio = 0;
+ hw_regs_t hw;
pdata = pdev->dev.platform_data;
@@ -106,15 +95,27 @@
res_alt->start, res_alt->end - res_alt->start + 1);
}
- hwif = plat_ide_locate_hwif(hwif_prop.plat_ide_mapbase,
- hwif_prop.plat_ide_alt_mapbase, pdata, res_irq->start, mmio);
-
+ hwif = ide_find_port((unsigned long)hwif_prop.plat_ide_mapbase);
if (!hwif) {
ret = -ENODEV;
goto out;
}
- hwif->gendev.parent = &pdev->dev;
- hwif->noprobe = 0;
+
+ memset(&hw, 0, sizeof(hw));
+ plat_ide_setup_ports(&hw, hwif_prop.plat_ide_mapbase,
+ hwif_prop.plat_ide_alt_mapbase,
+ pdata, res_irq->start);
+ hw.dev = &pdev->dev;
+
+ ide_init_port_hw(hwif, &hw);
+
+ if (mmio) {
+ hwif->mmio = 1;
+ default_hwif_mmiops(hwif);
+ }
+
+ hwif_prop.hwif = hwif;
+ hwif_prop.index = hwif->index;
idx[0] = hwif->index;
diff --git a/drivers/ide/legacy/macide.c b/drivers/ide/legacy/macide.c
index 5c6aa77..782d4c7 100644
--- a/drivers/ide/legacy/macide.c
+++ b/drivers/ide/legacy/macide.c
@@ -77,15 +77,17 @@
return 0;
}
+static const char *mac_ide_name[] =
+ { "Quadra", "Powerbook", "Powerbook Baboon" };
+
/*
* Probe for a Macintosh IDE interface
*/
-void __init macide_init(void)
+static int __init macide_init(void)
{
hw_regs_t hw;
ide_hwif_t *hwif;
- int index = -1;
switch (macintosh_config->ide_type) {
case MAC_IDE_QUADRA:
@@ -93,48 +95,50 @@
0, 0, macide_ack_intr,
// quadra_ide_iops,
IRQ_NUBUS_F);
- index = ide_register_hw(&hw, NULL, 1, &hwif);
break;
case MAC_IDE_PB:
ide_setup_ports(&hw, IDE_BASE, macide_offsets,
0, 0, macide_ack_intr,
// macide_pb_iops,
IRQ_NUBUS_C);
- index = ide_register_hw(&hw, NULL, 1, &hwif);
break;
case MAC_IDE_BABOON:
ide_setup_ports(&hw, BABOON_BASE, macide_offsets,
0, 0, NULL,
// macide_baboon_iops,
IRQ_BABOON_1);
- index = ide_register_hw(&hw, NULL, 1, &hwif);
- if (index == -1) break;
- if (macintosh_config->ident == MAC_MODEL_PB190) {
+ break;
+ default:
+ return -ENODEV;
+ }
+ printk(KERN_INFO "ide: Macintosh %s IDE controller\n",
+ mac_ide_name[macintosh_config->ide_type - 1]);
+
+ hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
+ if (hwif) {
+ u8 index = hwif->index;
+ u8 idx[4] = { index, 0xff, 0xff, 0xff };
+
+ ide_init_port_data(hwif, index);
+ ide_init_port_hw(hwif, &hw);
+
+ if (macintosh_config->ide_type == MAC_IDE_BABOON &&
+ macintosh_config->ident == MAC_MODEL_PB190) {
/* Fix breakage in ide-disk.c: drive capacity */
/* is not initialized for drives without a */
/* hardware ID, and we can't get that without */
/* probing the drive which freezes a 190. */
-
- ide_drive_t *drive = &ide_hwifs[index].drives[0];
+ ide_drive_t *drive = &hwif->drives[0];
drive->capacity64 = drive->cyl*drive->head*drive->sect;
-
}
- break;
- default:
- return;
- }
-
- if (index != -1) {
hwif->mmio = 1;
- if (macintosh_config->ide_type == MAC_IDE_QUADRA)
- printk(KERN_INFO "ide%d: Macintosh Quadra IDE interface\n", index);
- else if (macintosh_config->ide_type == MAC_IDE_PB)
- printk(KERN_INFO "ide%d: Macintosh Powerbook IDE interface\n", index);
- else if (macintosh_config->ide_type == MAC_IDE_BABOON)
- printk(KERN_INFO "ide%d: Macintosh Powerbook Baboon IDE interface\n", index);
- else
- printk(KERN_INFO "ide%d: Unknown Macintosh IDE interface\n", index);
+
+ ide_device_add(idx);
}
+
+ return 0;
}
+
+module_init(macide_init);
diff --git a/drivers/ide/legacy/q40ide.c b/drivers/ide/legacy/q40ide.c
index 6ea46a6..f532973 100644
--- a/drivers/ide/legacy/q40ide.c
+++ b/drivers/ide/legacy/q40ide.c
@@ -111,15 +111,17 @@
* Probe for Q40 IDE interfaces
*/
-void __init q40ide_init(void)
+static int __init q40ide_init(void)
{
int i;
ide_hwif_t *hwif;
- int index;
const char *name;
+ u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
if (!MACH_IS_Q40)
- return ;
+ return -ENODEV;
+
+ printk(KERN_INFO "ide: Q40 IDE controller\n");
for (i = 0; i < Q40IDE_NUM_HWIFS; i++) {
hw_regs_t hw;
@@ -141,10 +143,20 @@
0, NULL,
// m68kide_iops,
q40ide_default_irq(pcide_bases[i]));
- index = ide_register_hw(&hw, NULL, 1, &hwif);
- // **FIXME**
- if (index != -1)
+
+ hwif = ide_find_port(hw.io_ports[IDE_DATA_OFFSET]);
+ if (hwif) {
+ ide_init_port_data(hwif, hwif->index);
+ ide_init_port_hw(hwif, &hw);
hwif->mmio = 1;
+
+ idx[i] = hwif->index;
+ }
}
+
+ ide_device_add(idx);
+
+ return 0;
}
+module_init(q40ide_init);
diff --git a/drivers/ide/legacy/qd65xx.c b/drivers/ide/legacy/qd65xx.c
index 912e738..2bac4c1 100644
--- a/drivers/ide/legacy/qd65xx.c
+++ b/drivers/ide/legacy/qd65xx.c
@@ -478,8 +478,7 @@
module_param_named(probe, probe_qd65xx, bool, 0);
MODULE_PARM_DESC(probe, "probe for QD65xx chipsets");
-/* Can be called directly from ide.c. */
-int __init qd65xx_init(void)
+static int __init qd65xx_init(void)
{
if (probe_qd65xx == 0)
return -ENODEV;
@@ -492,9 +491,7 @@
return 0;
}
-#ifdef MODULE
module_init(qd65xx_init);
-#endif
MODULE_AUTHOR("Samuel Thibault");
MODULE_DESCRIPTION("support of qd65xx vlb ide chipset");
diff --git a/drivers/ide/legacy/umc8672.c b/drivers/ide/legacy/umc8672.c
index 79577b9..a1ae1ae 100644
--- a/drivers/ide/legacy/umc8672.c
+++ b/drivers/ide/legacy/umc8672.c
@@ -169,8 +169,7 @@
module_param_named(probe, probe_umc8672, bool, 0);
MODULE_PARM_DESC(probe, "probe for UMC8672 chipset");
-/* Can be called directly from ide.c. */
-int __init umc8672_init(void)
+static int __init umc8672_init(void)
{
if (probe_umc8672 == 0)
goto out;
@@ -181,9 +180,7 @@
return -ENODEV;;
}
-#ifdef MODULE
module_init(umc8672_init);
-#endif
MODULE_AUTHOR("Wolfram Podien");
MODULE_DESCRIPTION("Support for UMC 8672 IDE chipset");
diff --git a/drivers/ide/mips/au1xxx-ide.c b/drivers/ide/mips/au1xxx-ide.c
index a4d0d4c..2d3e511 100644
--- a/drivers/ide/mips/au1xxx-ide.c
+++ b/drivers/ide/mips/au1xxx-ide.c
@@ -395,26 +395,10 @@
return 0;
}
-static void auide_dma_host_on(ide_drive_t *drive)
+static void auide_dma_host_set(ide_drive_t *drive, int on)
{
}
-static int auide_dma_on(ide_drive_t *drive)
-{
- drive->using_dma = 1;
-
- return 0;
-}
-
-static void auide_dma_host_off(ide_drive_t *drive)
-{
-}
-
-static void auide_dma_off_quietly(ide_drive_t *drive)
-{
- drive->using_dma = 0;
-}
-
static void auide_dma_lost_irq(ide_drive_t *drive)
{
printk(KERN_ERR "%s: IRQ lost\n", drive->name);
@@ -641,12 +625,13 @@
/* FIXME: This might possibly break PCMCIA IDE devices */
hwif = &ide_hwifs[pdev->id];
- hwif->irq = ahwif->irq;
- hwif->chipset = ide_au1xxx;
memset(&hw, 0, sizeof(hw));
auide_setup_ports(&hw, ahwif);
- memcpy(hwif->io_ports, hw.io_ports, sizeof(hwif->io_ports));
+ hw.irq = ahwif->irq;
+ hw.chipset = ide_au1xxx;
+
+ ide_init_port_hw(hwif, &hw);
hwif->ultra_mask = 0x0; /* Disable Ultra DMA */
#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
@@ -660,7 +645,6 @@
hwif->pio_mask = ATA_PIO4;
hwif->host_flags = IDE_HFLAG_POST_SET_MODE;
- hwif->noprobe = 0;
hwif->drives[0].unmask = 1;
hwif->drives[1].unmask = 1;
@@ -682,29 +666,25 @@
hwif->set_dma_mode = &auide_set_dma_mode;
#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
- hwif->dma_off_quietly = &auide_dma_off_quietly;
hwif->dma_timeout = &auide_dma_timeout;
hwif->mdma_filter = &auide_mdma_filter;
+ hwif->dma_host_set = &auide_dma_host_set;
hwif->dma_exec_cmd = &auide_dma_exec_cmd;
hwif->dma_start = &auide_dma_start;
hwif->ide_dma_end = &auide_dma_end;
hwif->dma_setup = &auide_dma_setup;
hwif->ide_dma_test_irq = &auide_dma_test_irq;
- hwif->dma_host_off = &auide_dma_host_off;
- hwif->dma_host_on = &auide_dma_host_on;
hwif->dma_lost_irq = &auide_dma_lost_irq;
- hwif->ide_dma_on = &auide_dma_on;
-#else /* !CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA */
+#endif
hwif->channel = 0;
- hwif->hold = 1;
hwif->select_data = 0; /* no chipset-specific code */
hwif->config_data = 0; /* no chipset-specific code */
hwif->drives[0].autotune = 1; /* 1=autotune, 2=noautotune, 0=default */
hwif->drives[1].autotune = 1;
-#endif
+
hwif->drives[0].no_io_32bit = 1;
hwif->drives[1].no_io_32bit = 1;
diff --git a/drivers/ide/mips/swarm.c b/drivers/ide/mips/swarm.c
index 521edd4..8b3959d 100644
--- a/drivers/ide/mips/swarm.c
+++ b/drivers/ide/mips/swarm.c
@@ -117,6 +117,7 @@
default_hwif_mmiops(hwif);
/* Prevent resource map manipulation. */
hwif->mmio = 1;
+ hwif->chipset = ide_generic;
hwif->noprobe = 0;
for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; i++)
diff --git a/drivers/ide/pci/Makefile b/drivers/ide/pci/Makefile
index 95d1ea8..9480325 100644
--- a/drivers/ide/pci/Makefile
+++ b/drivers/ide/pci/Makefile
@@ -36,4 +36,8 @@
# Must appear at the end of the block
obj-$(CONFIG_BLK_DEV_GENERIC) += generic.o
+ifeq ($(CONFIG_BLK_DEV_CMD640), m)
+ obj-m += cmd640.o
+endif
+
EXTRA_CFLAGS := -Idrivers/ide
diff --git a/drivers/ide/pci/atiixp.c b/drivers/ide/pci/atiixp.c
index 5ae2656..4918719 100644
--- a/drivers/ide/pci/atiixp.c
+++ b/drivers/ide/pci/atiixp.c
@@ -1,5 +1,5 @@
/*
- * linux/drivers/ide/pci/atiixp.c Version 0.03 Aug 3 2007
+ * linux/drivers/ide/pci/atiixp.c Version 0.05 Nov 9 2007
*
* Copyright (C) 2003 ATI Inc. <hyu@ati.com>
* Copyright (C) 2004,2007 Bartlomiej Zolnierkiewicz
@@ -43,47 +43,8 @@
{ 0x02, 0x00 },
};
-static int save_mdma_mode[4];
-
static DEFINE_SPINLOCK(atiixp_lock);
-static void atiixp_dma_host_on(ide_drive_t *drive)
-{
- struct pci_dev *dev = drive->hwif->pci_dev;
- unsigned long flags;
- u16 tmp16;
-
- spin_lock_irqsave(&atiixp_lock, flags);
-
- pci_read_config_word(dev, ATIIXP_IDE_UDMA_CONTROL, &tmp16);
- if (save_mdma_mode[drive->dn])
- tmp16 &= ~(1 << drive->dn);
- else
- tmp16 |= (1 << drive->dn);
- pci_write_config_word(dev, ATIIXP_IDE_UDMA_CONTROL, tmp16);
-
- spin_unlock_irqrestore(&atiixp_lock, flags);
-
- ide_dma_host_on(drive);
-}
-
-static void atiixp_dma_host_off(ide_drive_t *drive)
-{
- struct pci_dev *dev = drive->hwif->pci_dev;
- unsigned long flags;
- u16 tmp16;
-
- spin_lock_irqsave(&atiixp_lock, flags);
-
- pci_read_config_word(dev, ATIIXP_IDE_UDMA_CONTROL, &tmp16);
- tmp16 &= ~(1 << drive->dn);
- pci_write_config_word(dev, ATIIXP_IDE_UDMA_CONTROL, tmp16);
-
- spin_unlock_irqrestore(&atiixp_lock, flags);
-
- ide_dma_host_off(drive);
-}
-
/**
* atiixp_set_pio_mode - set host controller for PIO mode
* @drive: drive
@@ -132,26 +93,33 @@
int timing_shift = (drive->dn & 2) ? 16 : 0 + (drive->dn & 1) ? 0 : 8;
u32 tmp32;
u16 tmp16;
+ u16 udma_ctl = 0;
spin_lock_irqsave(&atiixp_lock, flags);
- save_mdma_mode[drive->dn] = 0;
+ pci_read_config_word(dev, ATIIXP_IDE_UDMA_CONTROL, &udma_ctl);
+
if (speed >= XFER_UDMA_0) {
pci_read_config_word(dev, ATIIXP_IDE_UDMA_MODE, &tmp16);
tmp16 &= ~(0x07 << (drive->dn * 4));
tmp16 |= ((speed & 0x07) << (drive->dn * 4));
pci_write_config_word(dev, ATIIXP_IDE_UDMA_MODE, tmp16);
- } else {
- if ((speed >= XFER_MW_DMA_0) && (speed <= XFER_MW_DMA_2)) {
- save_mdma_mode[drive->dn] = speed;
- pci_read_config_dword(dev, ATIIXP_IDE_MDMA_TIMING, &tmp32);
- tmp32 &= ~(0xff << timing_shift);
- tmp32 |= (mdma_timing[speed & 0x03].recover_width << timing_shift) |
- (mdma_timing[speed & 0x03].command_width << (timing_shift + 4));
- pci_write_config_dword(dev, ATIIXP_IDE_MDMA_TIMING, tmp32);
- }
+
+ udma_ctl |= (1 << drive->dn);
+ } else if (speed >= XFER_MW_DMA_0) {
+ u8 i = speed & 0x03;
+
+ pci_read_config_dword(dev, ATIIXP_IDE_MDMA_TIMING, &tmp32);
+ tmp32 &= ~(0xff << timing_shift);
+ tmp32 |= (mdma_timing[i].recover_width << timing_shift) |
+ (mdma_timing[i].command_width << (timing_shift + 4));
+ pci_write_config_dword(dev, ATIIXP_IDE_MDMA_TIMING, tmp32);
+
+ udma_ctl &= ~(1 << drive->dn);
}
+ pci_write_config_word(dev, ATIIXP_IDE_UDMA_CONTROL, udma_ctl);
+
spin_unlock_irqrestore(&atiixp_lock, flags);
}
@@ -181,9 +149,6 @@
hwif->cbl = ATA_CBL_PATA80;
else
hwif->cbl = ATA_CBL_PATA40;
-
- hwif->dma_host_on = &atiixp_dma_host_on;
- hwif->dma_host_off = &atiixp_dma_host_off;
}
static const struct ide_port_info atiixp_pci_info[] __devinitdata = {
diff --git a/drivers/ide/pci/cmd640.c b/drivers/ide/pci/cmd640.c
index 4aa4810..da3565e 100644
--- a/drivers/ide/pci/cmd640.c
+++ b/drivers/ide/pci/cmd640.c
@@ -706,9 +706,9 @@
}
/*
- * Probe for a cmd640 chipset, and initialize it if found. Called from ide.c
+ * Probe for a cmd640 chipset, and initialize it if found.
*/
-int __init ide_probe_for_cmd640x (void)
+static int __init cmd640x_init(void)
{
#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
int second_port_toggled = 0;
@@ -717,6 +717,7 @@
const char *bus_type, *port2;
unsigned int index;
u8 b, cfr;
+ u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
if (cmd640_vlb && probe_for_cmd640_vlb()) {
bus_type = "VLB";
@@ -769,6 +770,8 @@
cmd_hwif0->set_pio_mode = &cmd640_set_pio_mode;
#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
+ idx[0] = cmd_hwif0->index;
+
/*
* Ensure compatibility by always using the slowest timings
* for access to the drive's command register block,
@@ -826,6 +829,8 @@
cmd_hwif1->pio_mask = ATA_PIO5;
cmd_hwif1->set_pio_mode = &cmd640_set_pio_mode;
#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
+
+ idx[1] = cmd_hwif1->index;
}
printk(KERN_INFO "%s: %sserialized, secondary interface %s\n", cmd_hwif1->name,
cmd_hwif0->serialized ? "" : "not ", port2);
@@ -872,6 +877,13 @@
#ifdef CMD640_DUMP_REGS
cmd640_dump_regs();
#endif
+
+ ide_device_add(idx);
+
return 1;
}
+module_param_named(probe_vlb, cmd640_vlb, bool, 0);
+MODULE_PARM_DESC(probe_vlb, "probe for VLB version of CMD640 chipset");
+
+module_init(cmd640x_init);
diff --git a/drivers/ide/pci/cmd64x.c b/drivers/ide/pci/cmd64x.c
index 0b1e947..cd4eb9d 100644
--- a/drivers/ide/pci/cmd64x.c
+++ b/drivers/ide/pci/cmd64x.c
@@ -1,5 +1,5 @@
/*
- * linux/drivers/ide/pci/cmd64x.c Version 1.52 Dec 24, 2007
+ * linux/drivers/ide/pci/cmd64x.c Version 1.53 Dec 24, 2007
*
* cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines.
* Due to massive hardware bugs, UltraDMA is only supported
@@ -22,8 +22,6 @@
#include <asm/io.h>
-#define DISPLAY_CMD64X_TIMINGS
-
#define CMD_DEBUG 0
#if CMD_DEBUG
@@ -37,11 +35,6 @@
*/
#define CFR 0x50
#define CFR_INTR_CH0 0x04
-#define CNTRL 0x51
-#define CNTRL_ENA_1ST 0x04
-#define CNTRL_ENA_2ND 0x08
-#define CNTRL_DIS_RA0 0x40
-#define CNTRL_DIS_RA1 0x80
#define CMDTIM 0x52
#define ARTTIM0 0x53
@@ -60,108 +53,13 @@
#define MRDMODE 0x71
#define MRDMODE_INTR_CH0 0x04
#define MRDMODE_INTR_CH1 0x08
-#define MRDMODE_BLK_CH0 0x10
-#define MRDMODE_BLK_CH1 0x20
-#define BMIDESR0 0x72
#define UDIDETCR0 0x73
#define DTPR0 0x74
#define BMIDECR1 0x78
#define BMIDECSR 0x79
-#define BMIDESR1 0x7A
#define UDIDETCR1 0x7B
#define DTPR1 0x7C
-#if defined(DISPLAY_CMD64X_TIMINGS) && defined(CONFIG_IDE_PROC_FS)
-#include <linux/stat.h>
-#include <linux/proc_fs.h>
-
-static u8 cmd64x_proc = 0;
-
-#define CMD_MAX_DEVS 5
-
-static struct pci_dev *cmd_devs[CMD_MAX_DEVS];
-static int n_cmd_devs;
-
-static char * print_cmd64x_get_info (char *buf, struct pci_dev *dev, int index)
-{
- char *p = buf;
- u8 reg72 = 0, reg73 = 0; /* primary */
- u8 reg7a = 0, reg7b = 0; /* secondary */
- u8 reg50 = 1, reg51 = 1, reg57 = 0, reg71 = 0; /* extra */
-
- p += sprintf(p, "\nController: %d\n", index);
- p += sprintf(p, "PCI-%x Chipset.\n", dev->device);
-
- (void) pci_read_config_byte(dev, CFR, ®50);
- (void) pci_read_config_byte(dev, CNTRL, ®51);
- (void) pci_read_config_byte(dev, ARTTIM23, ®57);
- (void) pci_read_config_byte(dev, MRDMODE, ®71);
- (void) pci_read_config_byte(dev, BMIDESR0, ®72);
- (void) pci_read_config_byte(dev, UDIDETCR0, ®73);
- (void) pci_read_config_byte(dev, BMIDESR1, ®7a);
- (void) pci_read_config_byte(dev, UDIDETCR1, ®7b);
-
- /* PCI0643/6 originally didn't have the primary channel enable bit */
- if ((dev->device == PCI_DEVICE_ID_CMD_643) ||
- (dev->device == PCI_DEVICE_ID_CMD_646 && dev->revision < 3))
- reg51 |= CNTRL_ENA_1ST;
-
- p += sprintf(p, "---------------- Primary Channel "
- "---------------- Secondary Channel ------------\n");
- p += sprintf(p, " %s %s\n",
- (reg51 & CNTRL_ENA_1ST) ? "enabled " : "disabled",
- (reg51 & CNTRL_ENA_2ND) ? "enabled " : "disabled");
- p += sprintf(p, "---------------- drive0 --------- drive1 "
- "-------- drive0 --------- drive1 ------\n");
- p += sprintf(p, "DMA enabled: %s %s"
- " %s %s\n",
- (reg72 & 0x20) ? "yes" : "no ", (reg72 & 0x40) ? "yes" : "no ",
- (reg7a & 0x20) ? "yes" : "no ", (reg7a & 0x40) ? "yes" : "no ");
- p += sprintf(p, "UltraDMA mode: %s (%c) %s (%c)",
- ( reg73 & 0x01) ? " on" : "off",
- ((reg73 & 0x30) == 0x30) ? ((reg73 & 0x04) ? '3' : '0') :
- ((reg73 & 0x30) == 0x20) ? ((reg73 & 0x04) ? '3' : '1') :
- ((reg73 & 0x30) == 0x10) ? ((reg73 & 0x04) ? '4' : '2') :
- ((reg73 & 0x30) == 0x00) ? ((reg73 & 0x04) ? '5' : '2') : '?',
- ( reg73 & 0x02) ? " on" : "off",
- ((reg73 & 0xC0) == 0xC0) ? ((reg73 & 0x08) ? '3' : '0') :
- ((reg73 & 0xC0) == 0x80) ? ((reg73 & 0x08) ? '3' : '1') :
- ((reg73 & 0xC0) == 0x40) ? ((reg73 & 0x08) ? '4' : '2') :
- ((reg73 & 0xC0) == 0x00) ? ((reg73 & 0x08) ? '5' : '2') : '?');
- p += sprintf(p, " %s (%c) %s (%c)\n",
- ( reg7b & 0x01) ? " on" : "off",
- ((reg7b & 0x30) == 0x30) ? ((reg7b & 0x04) ? '3' : '0') :
- ((reg7b & 0x30) == 0x20) ? ((reg7b & 0x04) ? '3' : '1') :
- ((reg7b & 0x30) == 0x10) ? ((reg7b & 0x04) ? '4' : '2') :
- ((reg7b & 0x30) == 0x00) ? ((reg7b & 0x04) ? '5' : '2') : '?',
- ( reg7b & 0x02) ? " on" : "off",
- ((reg7b & 0xC0) == 0xC0) ? ((reg7b & 0x08) ? '3' : '0') :
- ((reg7b & 0xC0) == 0x80) ? ((reg7b & 0x08) ? '3' : '1') :
- ((reg7b & 0xC0) == 0x40) ? ((reg7b & 0x08) ? '4' : '2') :
- ((reg7b & 0xC0) == 0x00) ? ((reg7b & 0x08) ? '5' : '2') : '?');
- p += sprintf(p, "Interrupt: %s, %s %s, %s\n",
- (reg71 & MRDMODE_BLK_CH0 ) ? "blocked" : "enabled",
- (reg50 & CFR_INTR_CH0 ) ? "pending" : "clear ",
- (reg71 & MRDMODE_BLK_CH1 ) ? "blocked" : "enabled",
- (reg57 & ARTTIM23_INTR_CH1) ? "pending" : "clear ");
-
- return (char *)p;
-}
-
-static int cmd64x_get_info (char *buffer, char **addr, off_t offset, int count)
-{
- char *p = buffer;
- int i;
-
- for (i = 0; i < n_cmd_devs; i++) {
- struct pci_dev *dev = cmd_devs[i];
- p = print_cmd64x_get_info(p, dev, i);
- }
- return p-buffer; /* => must be less than 4k! */
-}
-
-#endif /* defined(DISPLAY_CMD64X_TIMINGS) && defined(CONFIG_IDE_PROC_FS) */
-
static u8 quantize_timing(int timing, int quant)
{
return (timing + quant - 1) / quant;
@@ -472,16 +370,6 @@
mrdmode &= ~0x30;
(void) pci_write_config_byte(dev, MRDMODE, (mrdmode | 0x02));
-#if defined(DISPLAY_CMD64X_TIMINGS) && defined(CONFIG_IDE_PROC_FS)
-
- cmd_devs[n_cmd_devs++] = dev;
-
- if (!cmd64x_proc) {
- cmd64x_proc = 1;
- ide_pci_create_host_proc("cmd64x", cmd64x_get_info);
- }
-#endif /* DISPLAY_CMD64X_TIMINGS && CONFIG_IDE_PROC_FS */
-
return 0;
}
diff --git a/drivers/ide/pci/cs5520.c b/drivers/ide/pci/cs5520.c
index d1a91bc..6ec00b8 100644
--- a/drivers/ide/pci/cs5520.c
+++ b/drivers/ide/pci/cs5520.c
@@ -71,7 +71,6 @@
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *pdev = hwif->pci_dev;
int controller = drive->dn > 1 ? 1 : 0;
- u8 reg;
/* FIXME: if DMA = 1 do we need to set the DMA bit here ? */
@@ -91,11 +90,6 @@
pci_write_config_byte(pdev, 0x66 + 4*controller + (drive->dn&1),
(cs5520_pio_clocks[pio].recovery << 4) |
(cs5520_pio_clocks[pio].assert));
-
- /* Set the DMA enable/disable flag */
- reg = inb(hwif->dma_base + 0x02 + 8*controller);
- reg |= 1<<((drive->dn&1)+5);
- outb(reg, hwif->dma_base + 0x02 + 8*controller);
}
static void cs5520_set_dma_mode(ide_drive_t *drive, const u8 speed)
@@ -109,13 +103,14 @@
* We wrap the DMA activate to set the vdma flag. This is needed
* so that the IDE DMA layer issues PIO not DMA commands over the
* DMA channel
+ *
+ * ATAPI is harder so disable it for now using IDE_HFLAG_NO_ATAPI_DMA
*/
-
-static int cs5520_dma_on(ide_drive_t *drive)
+
+static void cs5520_dma_host_set(ide_drive_t *drive, int on)
{
- /* ATAPI is harder so leave it for now */
- drive->vdma = 1;
- return 0;
+ drive->vdma = on;
+ ide_dma_host_set(drive, on);
}
static void __devinit init_hwif_cs5520(ide_hwif_t *hwif)
@@ -126,7 +121,7 @@
if (hwif->dma_base == 0)
return;
- hwif->ide_dma_on = &cs5520_dma_on;
+ hwif->dma_host_set = &cs5520_dma_host_set;
}
#define DECLARE_CS_DEV(name_str) \
diff --git a/drivers/ide/pci/cy82c693.c b/drivers/ide/pci/cy82c693.c
index 1cd4e9c..3ec4c659 100644
--- a/drivers/ide/pci/cy82c693.c
+++ b/drivers/ide/pci/cy82c693.c
@@ -1,5 +1,5 @@
/*
- * linux/drivers/ide/pci/cy82c693.c Version 0.42 Oct 23, 2007
+ * linux/drivers/ide/pci/cy82c693.c Version 0.44 Nov 8, 2007
*
* Copyright (C) 1998-2000 Andreas S. Krebs (akrebs@altavista.net), Maintainer
* Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org>, Integrator
@@ -176,17 +176,12 @@
* set DMA mode a specific channel for CY82C693
*/
-static void cy82c693_dma_enable (ide_drive_t *drive, int mode, int single)
+static void cy82c693_set_dma_mode(ide_drive_t *drive, const u8 mode)
{
- u8 index = 0, data = 0;
+ ide_hwif_t *hwif = drive->hwif;
+ u8 single = (mode & 0x10) >> 4, index = 0, data = 0;
- if (mode>2) /* make sure we set a valid mode */
- mode = 2;
-
- if (mode > drive->id->tDMA) /* to be absolutly sure we have a valid mode */
- mode = drive->id->tDMA;
-
- index = (HWIF(drive)->channel==0) ? CY82_INDEX_CHANNEL0 : CY82_INDEX_CHANNEL1;
+ index = hwif->channel ? CY82_INDEX_CHANNEL1 : CY82_INDEX_CHANNEL0;
#if CY82C693_DEBUG_LOGS
/* for debug let's show the previous values */
@@ -199,7 +194,7 @@
(data&0x3), ((data>>2)&1));
#endif /* CY82C693_DEBUG_LOGS */
- data = (u8)mode|(u8)(single<<2);
+ data = (mode & 3) | (single << 2);
outb(index, CY82_INDEX_PORT);
outb(data, CY82_DATA_PORT);
@@ -207,7 +202,7 @@
#if CY82C693_DEBUG_INFO
printk(KERN_INFO "%s (ch=%d, dev=%d): set DMA mode to %d (single=%d)\n",
drive->name, HWIF(drive)->channel, drive->select.b.unit,
- mode, single);
+ mode & 3, single);
#endif /* CY82C693_DEBUG_INFO */
/*
@@ -230,39 +225,6 @@
#endif /* CY82C693_DEBUG_INFO */
}
-/*
- * used to set DMA mode for CY82C693 (single and multi modes)
- */
-static int cy82c693_ide_dma_on (ide_drive_t *drive)
-{
- struct hd_driveid *id = drive->id;
-
-#if CY82C693_DEBUG_INFO
- printk (KERN_INFO "dma_on: %s\n", drive->name);
-#endif /* CY82C693_DEBUG_INFO */
-
- if (id != NULL) {
- /* Enable DMA on any drive that has DMA
- * (multi or single) enabled
- */
- if (id->field_valid & 2) { /* regular DMA */
- int mmode, smode;
-
- mmode = id->dma_mword & (id->dma_mword >> 8);
- smode = id->dma_1word & (id->dma_1word >> 8);
-
- if (mmode != 0) {
- /* enable multi */
- cy82c693_dma_enable(drive, (mmode >> 1), 0);
- } else if (smode != 0) {
- /* enable single */
- cy82c693_dma_enable(drive, (smode >> 1), 1);
- }
- }
- }
- return __ide_dma_on(drive);
-}
-
static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
@@ -429,11 +391,7 @@
static void __devinit init_hwif_cy82c693(ide_hwif_t *hwif)
{
hwif->set_pio_mode = &cy82c693_set_pio_mode;
-
- if (hwif->dma_base == 0)
- return;
-
- hwif->ide_dma_on = &cy82c693_ide_dma_on;
+ hwif->set_dma_mode = &cy82c693_set_dma_mode;
}
static void __devinit init_iops_cy82c693(ide_hwif_t *hwif)
@@ -454,11 +412,11 @@
.init_iops = init_iops_cy82c693,
.init_hwif = init_hwif_cy82c693,
.chipset = ide_cy82c693,
- .host_flags = IDE_HFLAG_SINGLE | IDE_HFLAG_TRUST_BIOS_FOR_DMA |
+ .host_flags = IDE_HFLAG_SINGLE | IDE_HFLAG_CY82C693 |
IDE_HFLAG_BOOTABLE,
.pio_mask = ATA_PIO4,
- .swdma_mask = ATA_SWDMA2_ONLY,
- .mwdma_mask = ATA_MWDMA2_ONLY,
+ .swdma_mask = ATA_SWDMA2,
+ .mwdma_mask = ATA_MWDMA2,
};
static int __devinit cy82c693_init_one(struct pci_dev *dev, const struct pci_device_id *id)
diff --git a/drivers/ide/pci/delkin_cb.c b/drivers/ide/pci/delkin_cb.c
index 8382908..26aa492 100644
--- a/drivers/ide/pci/delkin_cb.c
+++ b/drivers/ide/pci/delkin_cb.c
@@ -80,7 +80,7 @@
hw.irq = dev->irq;
hw.chipset = ide_pci; /* this enables IRQ sharing */
- rc = ide_register_hw(&hw, &ide_undecoded_slave, 0, &hwif);
+ rc = ide_register_hw(&hw, &ide_undecoded_slave, &hwif);
if (rc < 0) {
printk(KERN_ERR "delkin_cb: ide_register_hw failed (%d)\n", rc);
pci_disable_device(dev);
diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c
index 3777fb8..1268593 100644
--- a/drivers/ide/pci/hpt366.c
+++ b/drivers/ide/pci/hpt366.c
@@ -725,15 +725,18 @@
hpt3xx_set_mode(drive, XFER_PIO_0 + pio);
}
-static int hpt3xx_quirkproc(ide_drive_t *drive)
+static void hpt3xx_quirkproc(ide_drive_t *drive)
{
struct hd_driveid *id = drive->id;
const char **list = quirk_drives;
while (*list)
- if (strstr(id->model, *list++))
- return 1;
- return 0;
+ if (strstr(id->model, *list++)) {
+ drive->quirk_list = 1;
+ return;
+ }
+
+ drive->quirk_list = 0;
}
static void hpt3xx_maskproc(ide_drive_t *drive, int mask)
diff --git a/drivers/ide/pci/it821x.c b/drivers/ide/pci/it821x.c
index 99b7d76..e610a53 100644
--- a/drivers/ide/pci/it821x.c
+++ b/drivers/ide/pci/it821x.c
@@ -431,33 +431,29 @@
}
/**
- * it821x_fixup - post init callback
- * @hwif: interface
+ * it821x_quirkproc - post init callback
+ * @drive: drive
*
- * This callback is run after the drives have been probed but
+ * This callback is run after the drive has been probed but
* before anything gets attached. It allows drivers to do any
* final tuning that is needed, or fixups to work around bugs.
*/
-static void __devinit it821x_fixups(ide_hwif_t *hwif)
+static void __devinit it821x_quirkproc(ide_drive_t *drive)
{
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- int i;
+ struct it821x_dev *itdev = ide_get_hwifdata(drive->hwif);
+ struct hd_driveid *id = drive->id;
+ u16 *idbits = (u16 *)drive->id;
- if(!itdev->smart) {
+ if (!itdev->smart) {
/*
* If we are in pass through mode then not much
* needs to be done, but we do bother to clear the
* IRQ mask as we may well be in PIO (eg rev 0x10)
* for now and we know unmasking is safe on this chipset.
*/
- for (i = 0; i < 2; i++) {
- ide_drive_t *drive = &hwif->drives[i];
- if(drive->present)
- drive->unmask = 1;
- }
- return;
- }
+ drive->unmask = 1;
+ } else {
/*
* Perform fixups on smart mode. We need to "lose" some
* capabilities the firmware lacks but does not filter, and
@@ -465,16 +461,6 @@
* in RAID mode.
*/
- for(i = 0; i < 2; i++) {
- ide_drive_t *drive = &hwif->drives[i];
- struct hd_driveid *id;
- u16 *idbits;
-
- if(!drive->present)
- continue;
- id = drive->id;
- idbits = (u16 *)drive->id;
-
/* Check for RAID v native */
if(strstr(id->model, "Integrated Technology Express")) {
/* In raid mode the ident block is slightly buggy
@@ -537,6 +523,8 @@
struct it821x_dev *idev = kzalloc(sizeof(struct it821x_dev), GFP_KERNEL);
u8 conf;
+ hwif->quirkproc = &it821x_quirkproc;
+
if (idev == NULL) {
printk(KERN_ERR "it821x: out of memory, falling back to legacy behaviour.\n");
return;
@@ -633,7 +621,6 @@
.name = name_str, \
.init_chipset = init_chipset_it821x, \
.init_hwif = init_hwif_it821x, \
- .fixup = it821x_fixups, \
.host_flags = IDE_HFLAG_BOOTABLE, \
.pio_mask = ATA_PIO4, \
}
diff --git a/drivers/ide/pci/pdc202xx_new.c b/drivers/ide/pci/pdc202xx_new.c
index ef4a99b..89d2363 100644
--- a/drivers/ide/pci/pdc202xx_new.c
+++ b/drivers/ide/pci/pdc202xx_new.c
@@ -203,14 +203,17 @@
return ATA_CBL_PATA80;
}
-static int pdcnew_quirkproc(ide_drive_t *drive)
+static void pdcnew_quirkproc(ide_drive_t *drive)
{
const char **list, *model = drive->id->model;
for (list = pdc_quirk_drives; *list != NULL; list++)
- if (strstr(model, *list) != NULL)
- return 2;
- return 0;
+ if (strstr(model, *list) != NULL) {
+ drive->quirk_list = 2;
+ return;
+ }
+
+ drive->quirk_list = 0;
}
static void pdcnew_reset(ide_drive_t *drive)
diff --git a/drivers/ide/pci/pdc202xx_old.c b/drivers/ide/pci/pdc202xx_old.c
index 67b2781..3a1e081 100644
--- a/drivers/ide/pci/pdc202xx_old.c
+++ b/drivers/ide/pci/pdc202xx_old.c
@@ -176,14 +176,17 @@
outb(clock & ~(hwif->channel ? 0x08 : 0x02), clock_reg);
}
-static int pdc202xx_quirkproc (ide_drive_t *drive)
+static void pdc202xx_quirkproc(ide_drive_t *drive)
{
const char **list, *model = drive->id->model;
for (list = pdc_quirk_drives; *list != NULL; list++)
- if (strstr(model, *list) != NULL)
- return 2;
- return 0;
+ if (strstr(model, *list) != NULL) {
+ drive->quirk_list = 2;
+ return;
+ }
+
+ drive->quirk_list = 0;
}
static void pdc202xx_old_ide_dma_start(ide_drive_t *drive)
diff --git a/drivers/ide/pci/sc1200.c b/drivers/ide/pci/sc1200.c
index fef20bd..32fdf53 100644
--- a/drivers/ide/pci/sc1200.c
+++ b/drivers/ide/pci/sc1200.c
@@ -220,9 +220,9 @@
}
if (mode != -1) {
printk("SC1200: %s: changing (U)DMA mode\n", drive->name);
- hwif->dma_off_quietly(drive);
- if (ide_set_dma_mode(drive, mode) == 0)
- hwif->dma_host_on(drive);
+ ide_dma_off_quietly(drive);
+ if (ide_set_dma_mode(drive, mode) == 0 && drive->using_dma)
+ hwif->dma_host_set(drive, 1);
return;
}
diff --git a/drivers/ide/pci/serverworks.c b/drivers/ide/pci/serverworks.c
index e9bd269..877c09b 100644
--- a/drivers/ide/pci/serverworks.c
+++ b/drivers/ide/pci/serverworks.c
@@ -164,25 +164,12 @@
ultra_timing &= ~(0x0F << (4*unit));
ultra_enable &= ~(0x01 << drive->dn);
- switch(speed) {
- case XFER_MW_DMA_2:
- case XFER_MW_DMA_1:
- case XFER_MW_DMA_0:
- dma_timing |= dma_modes[speed - XFER_MW_DMA_0];
- break;
-
- case XFER_UDMA_5:
- case XFER_UDMA_4:
- case XFER_UDMA_3:
- case XFER_UDMA_2:
- case XFER_UDMA_1:
- case XFER_UDMA_0:
- dma_timing |= dma_modes[2];
- ultra_timing |= ((udma_modes[speed - XFER_UDMA_0]) << (4*unit));
- ultra_enable |= (0x01 << drive->dn);
- default:
- break;
- }
+ if (speed >= XFER_UDMA_0) {
+ dma_timing |= dma_modes[2];
+ ultra_timing |= (udma_modes[speed - XFER_UDMA_0] << (4 * unit));
+ ultra_enable |= (0x01 << drive->dn);
+ } else if (speed >= XFER_MW_DMA_0)
+ dma_timing |= dma_modes[speed - XFER_MW_DMA_0];
pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
diff --git a/drivers/ide/pci/sgiioc4.c b/drivers/ide/pci/sgiioc4.c
index 7e9dade..9e0be7d 100644
--- a/drivers/ide/pci/sgiioc4.c
+++ b/drivers/ide/pci/sgiioc4.c
@@ -277,21 +277,6 @@
return dma_stat;
}
-static int
-sgiioc4_ide_dma_on(ide_drive_t * drive)
-{
- drive->using_dma = 1;
-
- return 0;
-}
-
-static void sgiioc4_dma_off_quietly(ide_drive_t *drive)
-{
- drive->using_dma = 0;
-
- drive->hwif->dma_host_off(drive);
-}
-
static void sgiioc4_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
}
@@ -303,13 +288,10 @@
return sgiioc4_checkirq(HWIF(drive));
}
-static void sgiioc4_dma_host_on(ide_drive_t * drive)
+static void sgiioc4_dma_host_set(ide_drive_t *drive, int on)
{
-}
-
-static void sgiioc4_dma_host_off(ide_drive_t * drive)
-{
- sgiioc4_clearirq(drive);
+ if (!on)
+ sgiioc4_clearirq(drive);
}
static void
@@ -593,14 +575,11 @@
hwif->mwdma_mask = ATA_MWDMA2_ONLY;
+ hwif->dma_host_set = &sgiioc4_dma_host_set;
hwif->dma_setup = &sgiioc4_ide_dma_setup;
hwif->dma_start = &sgiioc4_ide_dma_start;
hwif->ide_dma_end = &sgiioc4_ide_dma_end;
- hwif->ide_dma_on = &sgiioc4_ide_dma_on;
- hwif->dma_off_quietly = &sgiioc4_dma_off_quietly;
hwif->ide_dma_test_irq = &sgiioc4_ide_dma_test_irq;
- hwif->dma_host_on = &sgiioc4_dma_host_on;
- hwif->dma_host_off = &sgiioc4_dma_host_off;
hwif->dma_lost_irq = &sgiioc4_dma_lost_irq;
hwif->dma_timeout = &ide_dma_timeout;
}
@@ -614,6 +593,7 @@
ide_hwif_t *hwif;
int h;
u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
+ hw_regs_t hw;
/*
* Find an empty HWIF; if none available, return -ENOMEM.
@@ -653,21 +633,16 @@
return -ENOMEM;
}
- if (hwif->io_ports[IDE_DATA_OFFSET] != cmd_base) {
- hw_regs_t hw;
+ /* Initialize the IO registers */
+ memset(&hw, 0, sizeof(hw));
+ sgiioc4_init_hwif_ports(&hw, cmd_base, ctl, irqport);
+ hw.irq = dev->irq;
+ hw.chipset = ide_pci;
+ hw.dev = &dev->dev;
+ ide_init_port_hw(hwif, &hw);
- /* Initialize the IO registers */
- memset(&hw, 0, sizeof(hw));
- sgiioc4_init_hwif_ports(&hw, cmd_base, ctl, irqport);
- memcpy(hwif->io_ports, hw.io_ports, sizeof(hwif->io_ports));
- hwif->noprobe = !hwif->io_ports[IDE_DATA_OFFSET];
- }
-
- hwif->irq = dev->irq;
- hwif->chipset = ide_pci;
hwif->pci_dev = dev;
hwif->channel = 0; /* Single Channel chip */
- hwif->gendev.parent = &dev->dev;/* setup proper ancestral information */
/* The IOC4 uses MMIO rather than Port IO. */
default_hwif_mmiops(hwif);
diff --git a/drivers/ide/pci/siimage.c b/drivers/ide/pci/siimage.c
index 7b45eaf..908f37b 100644
--- a/drivers/ide/pci/siimage.c
+++ b/drivers/ide/pci/siimage.c
@@ -713,9 +713,6 @@
const char *s = &drive->id->model[0];
unsigned len;
- if (!drive->present)
- return 0;
-
len = strnlen(s, sizeof(drive->id->model));
if ((len > 4) && (!memcmp(s, "ST", 2))) {
@@ -730,18 +727,20 @@
}
/**
- * siimage_fixup - post probe fixups
- * @hwif: interface to fix up
+ * sil_quirkproc - post probe fixups
+ * @drive: drive
*
* Called after drive probe we use this to decide whether the
* Seagate fixup must be applied. This used to be in init_iops but
* that can occur before we know what drives are present.
*/
-static void __devinit siimage_fixup(ide_hwif_t *hwif)
+static void __devinit sil_quirkproc(ide_drive_t *drive)
{
+ ide_hwif_t *hwif = drive->hwif;
+
/* Try and raise the rqsize */
- if (!is_sata(hwif) || !is_dev_seagate_sata(&hwif->drives[0]))
+ if (!is_sata(hwif) || !is_dev_seagate_sata(drive))
hwif->rqsize = 128;
}
@@ -804,6 +803,7 @@
hwif->set_pio_mode = &sil_set_pio_mode;
hwif->set_dma_mode = &sil_set_dma_mode;
+ hwif->quirkproc = &sil_quirkproc;
if (sata) {
static int first = 1;
@@ -842,7 +842,6 @@
.init_chipset = init_chipset_siimage, \
.init_iops = init_iops_siimage, \
.init_hwif = init_hwif_siimage, \
- .fixup = siimage_fixup, \
.host_flags = IDE_HFLAG_BOOTABLE, \
.pio_mask = ATA_PIO4, \
.mwdma_mask = ATA_MWDMA2, \
diff --git a/drivers/ide/pci/sl82c105.c b/drivers/ide/pci/sl82c105.c
index 069f104..c7a125b 100644
--- a/drivers/ide/pci/sl82c105.c
+++ b/drivers/ide/pci/sl82c105.c
@@ -13,6 +13,7 @@
* -- Benjamin Herrenschmidt (01/11/03) benh@kernel.crashing.org
*
* Copyright (C) 2006-2007 MontaVista Software, Inc. <source@mvista.com>
+ * Copyright (C) 2007 Bartlomiej Zolnierkiewicz
*/
#include <linux/types.h>
@@ -90,14 +91,8 @@
drive->drive_data &= 0xffff0000;
drive->drive_data |= drv_ctrl;
- if (!drive->using_dma) {
- /*
- * If we are actually using MW DMA, then we can not
- * reprogram the interface drive control register.
- */
- pci_write_config_word(dev, reg, drv_ctrl);
- pci_read_config_word (dev, reg, &drv_ctrl);
- }
+ pci_write_config_word(dev, reg, drv_ctrl);
+ pci_read_config_word (dev, reg, &drv_ctrl);
printk(KERN_DEBUG "%s: selected %s (%dns) (%04X)\n", drive->name,
ide_xfer_verbose(pio + XFER_PIO_0),
@@ -123,17 +118,6 @@
*/
drive->drive_data &= 0x0000ffff;
drive->drive_data |= (unsigned long)drv_ctrl << 16;
-
- /*
- * If we are already using DMA, we just reprogram
- * the drive control register.
- */
- if (drive->using_dma) {
- struct pci_dev *dev = HWIF(drive)->pci_dev;
- int reg = 0x44 + drive->dn * 4;
-
- pci_write_config_word(dev, reg, drv_ctrl);
- }
}
/*
@@ -201,6 +185,11 @@
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
+ int reg = 0x44 + drive->dn * 4;
+
+ DBG(("%s(drive:%s)\n", __FUNCTION__, drive->name));
+
+ pci_write_config_word(dev, reg, drive->drive_data >> 16);
sl82c105_reset_host(dev);
ide_dma_start(drive);
@@ -214,64 +203,24 @@
ide_dma_timeout(drive);
}
-static int sl82c105_ide_dma_on(ide_drive_t *drive)
-{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
- int rc, reg = 0x44 + drive->dn * 4;
-
- DBG(("sl82c105_ide_dma_on(drive:%s)\n", drive->name));
-
- rc = __ide_dma_on(drive);
- if (rc == 0) {
- pci_write_config_word(dev, reg, drive->drive_data >> 16);
-
- printk(KERN_INFO "%s: DMA enabled\n", drive->name);
- }
- return rc;
-}
-
-static void sl82c105_dma_off_quietly(ide_drive_t *drive)
+static int sl82c105_dma_end(ide_drive_t *drive)
{
struct pci_dev *dev = HWIF(drive)->pci_dev;
int reg = 0x44 + drive->dn * 4;
+ int ret;
- DBG(("sl82c105_dma_off_quietly(drive:%s)\n", drive->name));
+ DBG(("%s(drive:%s)\n", __FUNCTION__, drive->name));
+
+ ret = __ide_dma_end(drive);
pci_write_config_word(dev, reg, drive->drive_data);
- ide_dma_off_quietly(drive);
-}
-
-/*
- * Ok, that is nasty, but we must make sure the DMA timings
- * won't be used for a PIO access. The solution here is
- * to make sure the 16 bits mode is diabled on the channel
- * when DMA is enabled, thus causing the chip to use PIO0
- * timings for those operations.
- */
-static void sl82c105_selectproc(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
- u32 val, old, mask;
-
- //DBG(("sl82c105_selectproc(drive:%s)\n", drive->name));
-
- mask = hwif->channel ? CTRL_P1F16 : CTRL_P0F16;
- old = val = (u32)pci_get_drvdata(dev);
- if (drive->using_dma)
- val &= ~mask;
- else
- val |= mask;
- if (old != val) {
- pci_write_config_dword(dev, 0x40, val);
- pci_set_drvdata(dev, (void *)val);
- }
+ return ret;
}
/*
* ATA reset will clear the 16 bits mode in the control
- * register, we need to update our cache
+ * register, we need to reprogram it
*/
static void sl82c105_resetproc(ide_drive_t *drive)
{
@@ -281,7 +230,8 @@
DBG(("sl82c105_resetproc(drive:%s)\n", drive->name));
pci_read_config_dword(dev, 0x40, &val);
- pci_set_drvdata(dev, (void *)val);
+ val |= (CTRL_P1F16 | CTRL_P0F16);
+ pci_write_config_dword(dev, 0x40, val);
}
/*
@@ -334,7 +284,6 @@
pci_read_config_dword(dev, 0x40, &val);
val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
pci_write_config_dword(dev, 0x40, val);
- pci_set_drvdata(dev, (void *)val);
return dev->irq;
}
@@ -350,7 +299,6 @@
hwif->set_pio_mode = &sl82c105_set_pio_mode;
hwif->set_dma_mode = &sl82c105_set_dma_mode;
- hwif->selectproc = &sl82c105_selectproc;
hwif->resetproc = &sl82c105_resetproc;
if (!hwif->dma_base)
@@ -369,10 +317,9 @@
hwif->mwdma_mask = ATA_MWDMA2;
- hwif->ide_dma_on = &sl82c105_ide_dma_on;
- hwif->dma_off_quietly = &sl82c105_dma_off_quietly;
hwif->dma_lost_irq = &sl82c105_dma_lost_irq;
hwif->dma_start = &sl82c105_dma_start;
+ hwif->ide_dma_end = &sl82c105_dma_end;
hwif->dma_timeout = &sl82c105_dma_timeout;
if (hwif->mate)
diff --git a/drivers/ide/pci/trm290.c b/drivers/ide/pci/trm290.c
index 0151d7f..04cd893 100644
--- a/drivers/ide/pci/trm290.c
+++ b/drivers/ide/pci/trm290.c
@@ -241,11 +241,7 @@
return (status == 0x00ff);
}
-static void trm290_dma_host_on(ide_drive_t *drive)
-{
-}
-
-static void trm290_dma_host_off(ide_drive_t *drive)
+static void trm290_dma_host_set(ide_drive_t *drive, int on)
{
}
@@ -289,8 +285,7 @@
ide_setup_dma(hwif, (hwif->config_data + 4) ^ (hwif->channel ? 0x0080 : 0x0000), 3);
- hwif->dma_host_off = &trm290_dma_host_off;
- hwif->dma_host_on = &trm290_dma_host_on;
+ hwif->dma_host_set = &trm290_dma_host_set;
hwif->dma_setup = &trm290_dma_setup;
hwif->dma_exec_cmd = &trm290_dma_exec_cmd;
hwif->dma_start = &trm290_dma_start;
diff --git a/drivers/ide/ppc/Makefile b/drivers/ide/ppc/Makefile
new file mode 100644
index 0000000..65af584
--- /dev/null
+++ b/drivers/ide/ppc/Makefile
@@ -0,0 +1,3 @@
+
+obj-$(CONFIG_BLK_DEV_IDE_PMAC) += pmac.o
+obj-$(CONFIG_BLK_DEV_MPC8xx_IDE) += mpc8xx.o
diff --git a/drivers/ide/ppc/mpc8xx.c b/drivers/ide/ppc/mpc8xx.c
index 5f0da35..3fd5d45 100644
--- a/drivers/ide/ppc/mpc8xx.c
+++ b/drivers/ide/ppc/mpc8xx.c
@@ -838,3 +838,21 @@
ppc_ide_md.default_io_base = m8xx_ide_default_io_base;
ppc_ide_md.ide_init_hwif = m8xx_ide_init_hwif_ports;
}
+
+static int __init mpc8xx_ide_probe(void)
+{
+ u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
+
+#ifdef IDE0_BASE_OFFSET
+ idx[0] = 0;
+#ifdef IDE1_BASE_OFFSET
+ idx[1] = 1;
+#endif
+#endif
+
+ ide_device_add(idx);
+
+ return 0;
+}
+
+module_init(mpc8xx_ide_probe);
diff --git a/drivers/ide/ppc/pmac.c b/drivers/ide/ppc/pmac.c
index 3dce800..736d12c 100644
--- a/drivers/ide/ppc/pmac.c
+++ b/drivers/ide/ppc/pmac.c
@@ -1012,12 +1012,11 @@
* rare machines unfortunately, but it's better this way.
*/
static int
-pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
+pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif, hw_regs_t *hw)
{
struct device_node *np = pmif->node;
const int *bidp;
u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
- hw_regs_t hw;
pmif->cable_80 = 0;
pmif->broken_dma = pmif->broken_dma_warn = 0;
@@ -1103,11 +1102,9 @@
/* Tell common code _not_ to mess with resources */
hwif->mmio = 1;
hwif->hwif_data = pmif;
- memset(&hw, 0, sizeof(hw));
- pmac_ide_init_hwif_ports(&hw, pmif->regbase, 0, &hwif->irq);
- memcpy(hwif->io_ports, hw.io_ports, sizeof(hwif->io_ports));
- hwif->chipset = ide_pmac;
- hwif->noprobe = !hwif->io_ports[IDE_DATA_OFFSET] || pmif->mediabay;
+ hw->chipset = ide_pmac;
+ ide_init_port_hw(hwif, hw);
+ hwif->noprobe = pmif->mediabay;
hwif->hold = pmif->mediabay;
hwif->cbl = pmif->cable_80 ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
hwif->drives[0].unmask = 1;
@@ -1136,8 +1133,6 @@
hwif->noprobe = 0;
#endif /* CONFIG_PMAC_MEDIABAY */
- hwif->sg_max_nents = MAX_DCMDS;
-
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
/* has a DBDMA controller channel */
if (pmif->dma_regs)
@@ -1163,6 +1158,7 @@
ide_hwif_t *hwif;
pmac_ide_hwif_t *pmif;
int i, rc;
+ hw_regs_t hw;
i = 0;
while (i < MAX_HWIFS && (ide_hwifs[i].io_ports[IDE_DATA_OFFSET] != 0
@@ -1205,7 +1201,6 @@
regbase = (unsigned long) base;
hwif->pci_dev = mdev->bus->pdev;
- hwif->gendev.parent = &mdev->ofdev.dev;
pmif->mdev = mdev;
pmif->node = mdev->ofdev.node;
@@ -1223,7 +1218,12 @@
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
dev_set_drvdata(&mdev->ofdev.dev, hwif);
- rc = pmac_ide_setup_device(pmif, hwif);
+ memset(&hw, 0, sizeof(hw));
+ pmac_ide_init_hwif_ports(&hw, pmif->regbase, 0, NULL);
+ hw.irq = irq;
+ hw.dev = &mdev->ofdev.dev;
+
+ rc = pmac_ide_setup_device(pmif, hwif, &hw);
if (rc != 0) {
/* The inteface is released to the common IDE layer */
dev_set_drvdata(&mdev->ofdev.dev, NULL);
@@ -1282,6 +1282,7 @@
void __iomem *base;
unsigned long rbase, rlen;
int i, rc;
+ hw_regs_t hw;
np = pci_device_to_OF_node(pdev);
if (np == NULL) {
@@ -1315,7 +1316,6 @@
}
hwif->pci_dev = pdev;
- hwif->gendev.parent = &pdev->dev;
pmif->mdev = NULL;
pmif->node = np;
@@ -1332,7 +1332,12 @@
pci_set_drvdata(pdev, hwif);
- rc = pmac_ide_setup_device(pmif, hwif);
+ memset(&hw, 0, sizeof(hw));
+ pmac_ide_init_hwif_ports(&hw, pmif->regbase, 0, NULL);
+ hw.irq = pdev->irq;
+ hw.dev = &pdev->dev;
+
+ rc = pmac_ide_setup_device(pmif, hwif, &hw);
if (rc != 0) {
/* The inteface is released to the common IDE layer */
pci_set_drvdata(pdev, NULL);
@@ -1698,11 +1703,7 @@
return 1;
}
-static void pmac_ide_dma_host_off(ide_drive_t *drive)
-{
-}
-
-static void pmac_ide_dma_host_on(ide_drive_t *drive)
+static void pmac_ide_dma_host_set(ide_drive_t *drive, int on)
{
}
@@ -1748,15 +1749,14 @@
return;
}
- hwif->dma_off_quietly = &ide_dma_off_quietly;
- hwif->ide_dma_on = &__ide_dma_on;
+ hwif->sg_max_nents = MAX_DCMDS;
+
+ hwif->dma_host_set = &pmac_ide_dma_host_set;
hwif->dma_setup = &pmac_ide_dma_setup;
hwif->dma_exec_cmd = &pmac_ide_dma_exec_cmd;
hwif->dma_start = &pmac_ide_dma_start;
hwif->ide_dma_end = &pmac_ide_dma_end;
hwif->ide_dma_test_irq = &pmac_ide_dma_test_irq;
- hwif->dma_host_off = &pmac_ide_dma_host_off;
- hwif->dma_host_on = &pmac_ide_dma_host_on;
hwif->dma_timeout = &ide_dma_timeout;
hwif->dma_lost_irq = &pmac_ide_dma_lost_irq;
@@ -1786,3 +1786,5 @@
}
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
+
+module_init(pmac_ide_probe);
diff --git a/drivers/ide/setup-pci.c b/drivers/ide/setup-pci.c
index d2cd5a3..676c66e 100644
--- a/drivers/ide/setup-pci.c
+++ b/drivers/ide/setup-pci.c
@@ -165,13 +165,17 @@
dma_base = pci_resource_start(dev, baridx);
- if (dma_base == 0)
+ if (dma_base == 0) {
printk(KERN_ERR "%s: DMA base is invalid\n", d->name);
+ return 0;
+ }
}
- if ((d->host_flags & IDE_HFLAG_CS5520) == 0 && dma_base) {
+ if (hwif->channel)
+ dma_base += 8;
+
+ if ((d->host_flags & IDE_HFLAG_CS5520) == 0) {
u8 simplex_stat = 0;
- dma_base += hwif->channel ? 8 : 0;
switch(dev->device) {
case PCI_DEVICE_ID_AL_M5219:
@@ -359,6 +363,8 @@
unsigned long ctl = 0, base = 0;
ide_hwif_t *hwif;
u8 bootable = (d->host_flags & IDE_HFLAG_BOOTABLE) ? 1 : 0;
+ u8 oldnoprobe = 0;
+ struct hw_regs_s hw;
if ((d->host_flags & IDE_HFLAG_ISA_PORTS) == 0) {
/* Possibly we should fail if these checks report true */
@@ -381,26 +387,25 @@
}
if ((hwif = ide_match_hwif(base, bootable, d->name)) == NULL)
return NULL; /* no room in ide_hwifs[] */
- if (hwif->io_ports[IDE_DATA_OFFSET] != base ||
- hwif->io_ports[IDE_CONTROL_OFFSET] != (ctl | 2)) {
- hw_regs_t hw;
- memset(&hw, 0, sizeof(hw));
-#ifndef CONFIG_IDE_ARCH_OBSOLETE_INIT
- ide_std_init_ports(&hw, base, ctl | 2);
-#else
- ide_init_hwif_ports(&hw, base, ctl | 2, NULL);
-#endif
- memcpy(hwif->io_ports, hw.io_ports, sizeof(hwif->io_ports));
- hwif->noprobe = !hwif->io_ports[IDE_DATA_OFFSET];
- }
- hwif->chipset = d->chipset ? d->chipset : ide_pci;
+ memset(&hw, 0, sizeof(hw));
+ hw.irq = hwif->irq ? hwif->irq : irq;
+ hw.dev = &dev->dev;
+ hw.chipset = d->chipset ? d->chipset : ide_pci;
+ ide_std_init_ports(&hw, base, ctl | 2);
+
+ if (hwif->io_ports[IDE_DATA_OFFSET] == base &&
+ hwif->io_ports[IDE_CONTROL_OFFSET] == (ctl | 2))
+ oldnoprobe = hwif->noprobe;
+
+ ide_init_port_hw(hwif, &hw);
+
+ hwif->noprobe = oldnoprobe;
+
hwif->pci_dev = dev;
hwif->cds = d;
hwif->channel = port;
- if (!hwif->irq)
- hwif->irq = irq;
if (mate) {
hwif->mate = mate;
mate->mate = hwif;
@@ -535,12 +540,8 @@
if ((hwif = ide_hwif_configure(dev, d, mate, port, pciirq)) == NULL)
continue;
- /* setup proper ancestral information */
- hwif->gendev.parent = &dev->dev;
-
*(idx + port) = hwif->index;
-
if (d->init_iops)
d->init_iops(hwif);
@@ -551,8 +552,6 @@
(d->host_flags & IDE_HFLAG_FORCE_LEGACY_IRQS))
hwif->irq = port ? 15 : 14;
- hwif->fixup = d->fixup;
-
hwif->host_flags = d->host_flags;
hwif->pio_mask = d->pio_mask;
@@ -699,105 +698,3 @@
}
EXPORT_SYMBOL_GPL(ide_setup_pci_devices);
-
-#ifdef CONFIG_IDEPCI_PCIBUS_ORDER
-/*
- * Module interfaces
- */
-
-static int pre_init = 1; /* Before first ordered IDE scan */
-static LIST_HEAD(ide_pci_drivers);
-
-/*
- * __ide_pci_register_driver - attach IDE driver
- * @driver: pci driver
- * @module: owner module of the driver
- *
- * Registers a driver with the IDE layer. The IDE layer arranges that
- * boot time setup is done in the expected device order and then
- * hands the controllers off to the core PCI code to do the rest of
- * the work.
- *
- * Returns are the same as for pci_register_driver
- */
-
-int __ide_pci_register_driver(struct pci_driver *driver, struct module *module,
- const char *mod_name)
-{
- if (!pre_init)
- return __pci_register_driver(driver, module, mod_name);
- driver->driver.owner = module;
- list_add_tail(&driver->node, &ide_pci_drivers);
- return 0;
-}
-EXPORT_SYMBOL_GPL(__ide_pci_register_driver);
-
-/**
- * ide_scan_pcidev - find an IDE driver for a device
- * @dev: PCI device to check
- *
- * Look for an IDE driver to handle the device we are considering.
- * This is only used during boot up to get the ordering correct. After
- * boot up the pci layer takes over the job.
- */
-
-static int __init ide_scan_pcidev(struct pci_dev *dev)
-{
- struct list_head *l;
- struct pci_driver *d;
-
- list_for_each(l, &ide_pci_drivers) {
- d = list_entry(l, struct pci_driver, node);
- if (d->id_table) {
- const struct pci_device_id *id =
- pci_match_id(d->id_table, dev);
-
- if (id != NULL && d->probe(dev, id) >= 0) {
- dev->driver = d;
- pci_dev_get(dev);
- return 1;
- }
- }
- }
- return 0;
-}
-
-/**
- * ide_scan_pcibus - perform the initial IDE driver scan
- * @scan_direction: set for reverse order scanning
- *
- * Perform the initial bus rather than driver ordered scan of the
- * PCI drivers. After this all IDE pci handling becomes standard
- * module ordering not traditionally ordered.
- */
-
-void __init ide_scan_pcibus (int scan_direction)
-{
- struct pci_dev *dev = NULL;
- struct pci_driver *d;
- struct list_head *l, *n;
-
- pre_init = 0;
- if (!scan_direction)
- while ((dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev)))
- ide_scan_pcidev(dev);
- else
- while ((dev = pci_get_device_reverse(PCI_ANY_ID, PCI_ANY_ID,
- dev)))
- ide_scan_pcidev(dev);
-
- /*
- * Hand the drivers over to the PCI layer now we
- * are post init.
- */
-
- list_for_each_safe(l, n, &ide_pci_drivers) {
- list_del(l);
- d = list_entry(l, struct pci_driver, node);
- if (__pci_register_driver(d, d->driver.owner,
- d->driver.mod_name))
- printk(KERN_ERR "%s: failed to register %s driver\n",
- __FUNCTION__, d->driver.mod_name);
- }
-}
-#endif
diff --git a/drivers/macintosh/mediabay.c b/drivers/macintosh/mediabay.c
index 48d647a..eaba4a9 100644
--- a/drivers/macintosh/mediabay.c
+++ b/drivers/macintosh/mediabay.c
@@ -563,7 +563,8 @@
ide_init_hwif_ports(&hw, (unsigned long) bay->cd_base, (unsigned long) 0, NULL);
hw.irq = bay->cd_irq;
hw.chipset = ide_pmac;
- bay->cd_index = ide_register_hw(&hw, NULL, 0, NULL);
+ bay->cd_index =
+ ide_register_hw(&hw, NULL, NULL);
pmu_resume();
}
if (bay->cd_index == -1) {
diff --git a/include/linux/blkdev.h b/include/linux/blkdev.h
index bd20a4e..49b7a4c 100644
--- a/include/linux/blkdev.h
+++ b/include/linux/blkdev.h
@@ -143,7 +143,6 @@
* use REQ_TYPE_SPECIAL and use rq->cmd[0] with the range of driver
* private REQ_LB opcodes to differentiate what type of request this is
*/
- REQ_TYPE_ATA_CMD,
REQ_TYPE_ATA_TASKFILE,
REQ_TYPE_ATA_PC,
};
diff --git a/include/linux/ide.h b/include/linux/ide.h
index 1e44099..27cb39d 100644
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -107,7 +107,6 @@
#define BAD_W_STAT (BAD_R_STAT | WRERR_STAT)
#define BAD_STAT (BAD_R_STAT | DRQ_STAT)
#define DRIVE_READY (READY_STAT | SEEK_STAT)
-#define DATA_READY (DRQ_STAT)
#define BAD_CRC (ABRT_ERR | ICRC_ERR)
@@ -198,8 +197,11 @@
} hw_regs_t;
struct hwif_s * ide_find_port(unsigned long);
+void ide_init_port_data(struct hwif_s *, unsigned int);
+void ide_init_port_hw(struct hwif_s *, hw_regs_t *);
-int ide_register_hw(hw_regs_t *, void (*)(struct hwif_s *), int,
+struct ide_drive_s;
+int ide_register_hw(hw_regs_t *, void (*)(struct ide_drive_s *),
struct hwif_s **);
void ide_setup_ports( hw_regs_t *hw,
@@ -391,7 +393,6 @@
u8 state; /* retry state */
u8 waiting_for_dma; /* dma currently in progress */
u8 unmask; /* okay to unmask other irqs */
- u8 bswap; /* byte swap data */
u8 noflush; /* don't attempt flushes */
u8 dsc_overlap; /* DSC overlap */
u8 nice1; /* give potential excess bandwidth */
@@ -527,31 +528,26 @@
/* special host masking for drive selection */
void (*maskproc)(ide_drive_t *, int);
/* check host's drive quirk list */
- int (*quirkproc)(ide_drive_t *);
+ void (*quirkproc)(ide_drive_t *);
/* driver soft-power interface */
int (*busproc)(ide_drive_t *, int);
#endif
u8 (*mdma_filter)(ide_drive_t *);
u8 (*udma_filter)(ide_drive_t *);
- void (*fixup)(struct hwif_s *);
-
void (*ata_input_data)(ide_drive_t *, void *, u32);
void (*ata_output_data)(ide_drive_t *, void *, u32);
void (*atapi_input_bytes)(ide_drive_t *, void *, u32);
void (*atapi_output_bytes)(ide_drive_t *, void *, u32);
+ void (*dma_host_set)(ide_drive_t *, int);
int (*dma_setup)(ide_drive_t *);
void (*dma_exec_cmd)(ide_drive_t *, u8);
void (*dma_start)(ide_drive_t *);
int (*ide_dma_end)(ide_drive_t *drive);
- int (*ide_dma_on)(ide_drive_t *drive);
- void (*dma_off_quietly)(ide_drive_t *drive);
int (*ide_dma_test_irq)(ide_drive_t *drive);
void (*ide_dma_clear_irq)(ide_drive_t *drive);
- void (*dma_host_on)(ide_drive_t *drive);
- void (*dma_host_off)(ide_drive_t *drive);
void (*dma_lost_irq)(ide_drive_t *drive);
void (*dma_timeout)(ide_drive_t *drive);
@@ -874,14 +870,6 @@
extern void ide_end_drive_cmd(ide_drive_t *, u8, u8);
-/*
- * Issue ATA command and wait for completion.
- * Use for implementing commands in kernel
- *
- * (ide_drive_t *drive, u8 cmd, u8 nsect, u8 feature, u8 sectors, u8 *buf)
- */
-extern int ide_wait_cmd(ide_drive_t *, u8, u8, u8, u8, u8 *);
-
enum {
IDE_TFLAG_LBA48 = (1 << 0),
IDE_TFLAG_NO_SELECT_MASK = (1 << 1),
@@ -934,6 +922,14 @@
IDE_TFLAG_IN_TF = IDE_TFLAG_IN_NSECT |
IDE_TFLAG_IN_LBA,
IDE_TFLAG_IN_DEVICE = (1 << 29),
+ IDE_TFLAG_HOB = IDE_TFLAG_OUT_HOB |
+ IDE_TFLAG_IN_HOB,
+ IDE_TFLAG_TF = IDE_TFLAG_OUT_TF |
+ IDE_TFLAG_IN_TF,
+ IDE_TFLAG_DEVICE = IDE_TFLAG_OUT_DEVICE |
+ IDE_TFLAG_IN_DEVICE,
+ /* force 16-bit I/O operations */
+ IDE_TFLAG_IO_16BIT = (1 << 30),
};
struct ide_taskfile {
@@ -988,6 +984,10 @@
ide_startstop_t do_rw_taskfile(ide_drive_t *, ide_task_t *);
+void task_end_request(ide_drive_t *, struct request *, u8);
+
+u8 wait_drive_not_busy(ide_drive_t *);
+
int ide_raw_taskfile(ide_drive_t *, ide_task_t *, u8 *, u16);
int ide_no_data_taskfile(ide_drive_t *, ide_task_t *);
@@ -1015,10 +1015,9 @@
void ide_init_disk(struct gendisk *, ide_drive_t *);
-extern int ideprobe_init(void);
-
#ifdef CONFIG_IDEPCI_PCIBUS_ORDER
-extern void ide_scan_pcibus(int scan_direction) __init;
+extern int ide_scan_direction;
+int __init ide_scan_pcibus(void);
extern int __ide_pci_register_driver(struct pci_driver *driver, struct module *owner, const char *mod_name);
#define ide_pci_register_driver(d) __ide_pci_register_driver(d, THIS_MODULE, KBUILD_MODNAME)
#else
@@ -1095,6 +1094,8 @@
/* unmask IRQs */
IDE_HFLAG_UNMASK_IRQS = (1 << 25),
IDE_HFLAG_ABUSE_SET_DMA_MODE = (1 << 26),
+ /* host is CY82C693 */
+ IDE_HFLAG_CY82C693 = (1 << 27),
};
#ifdef CONFIG_BLK_DEV_OFFBOARD
@@ -1109,7 +1110,6 @@
void (*init_iops)(ide_hwif_t *);
void (*init_hwif)(ide_hwif_t *);
void (*init_dma)(ide_hwif_t *, unsigned long);
- void (*fixup)(ide_hwif_t *);
ide_pci_enablebit_t enablebits[2];
hwif_chipset_t chipset;
u8 extra;
@@ -1147,7 +1147,9 @@
return ide_find_dma_mode(drive, XFER_UDMA_6);
}
+void ide_dma_off_quietly(ide_drive_t *);
void ide_dma_off(ide_drive_t *);
+void ide_dma_on(ide_drive_t *);
int ide_set_dma(ide_drive_t *);
ide_startstop_t ide_dma_intr(ide_drive_t *);
@@ -1158,10 +1160,7 @@
extern int ide_release_dma(ide_hwif_t *);
extern void ide_setup_dma(ide_hwif_t *, unsigned long, unsigned int);
-void ide_dma_host_off(ide_drive_t *);
-void ide_dma_off_quietly(ide_drive_t *);
-void ide_dma_host_on(ide_drive_t *);
-extern int __ide_dma_on(ide_drive_t *);
+void ide_dma_host_set(ide_drive_t *, int);
extern int ide_dma_setup(ide_drive_t *);
extern void ide_dma_start(ide_drive_t *);
extern int __ide_dma_end(ide_drive_t *);
@@ -1173,7 +1172,9 @@
static inline int ide_id_dma_bug(ide_drive_t *drive) { return 0; }
static inline u8 ide_find_dma_mode(ide_drive_t *drive, u8 speed) { return 0; }
static inline u8 ide_max_dma_mode(ide_drive_t *drive) { return 0; }
+static inline void ide_dma_off_quietly(ide_drive_t *drive) { ; }
static inline void ide_dma_off(ide_drive_t *drive) { ; }
+static inline void ide_dma_on(ide_drive_t *drive) { ; }
static inline void ide_dma_verbose(ide_drive_t *drive) { ; }
static inline int ide_set_dma(ide_drive_t *drive) { return 1; }
#endif /* CONFIG_BLK_DEV_IDEDMA */
@@ -1203,8 +1204,9 @@
void ide_register_region(struct gendisk *);
void ide_unregister_region(struct gendisk *);
-void ide_undecoded_slave(ide_hwif_t *);
+void ide_undecoded_slave(ide_drive_t *);
+int ide_device_add_all(u8 *idx);
int ide_device_add(u8 idx[4]);
static inline void *ide_get_hwifdata (ide_hwif_t * hwif)
@@ -1302,4 +1304,9 @@
return &hwif->drives[(drive->dn ^ 1) & 1];
}
+static inline void ide_set_irq(ide_drive_t *drive, int on)
+{
+ drive->hwif->OUTB(drive->ctl | (on ? 0 : 2), IDE_CONTROL_REG);
+}
+
#endif /* _IDE_H */