| /* |
| * imx-ssi.c -- ALSA Soc Audio Layer |
| * |
| * Copyright 2009 Sascha Hauer <s.hauer@pengutronix.de> |
| * |
| * This code is based on code copyrighted by Freescale, |
| * Liam Girdwood, Javier Martin and probably others. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| * |
| * |
| * The i.MX SSI core has some nasty limitations in AC97 mode. While most |
| * sane processor vendors have a FIFO per AC97 slot, the i.MX has only |
| * one FIFO which combines all valid receive slots. We cannot even select |
| * which slots we want to receive. The WM9712 with which this driver |
| * was developed with always sends GPIO status data in slot 12 which |
| * we receive in our (PCM-) data stream. The only chance we have is to |
| * manually skip this data in the FIQ handler. With sampling rates different |
| * from 48000Hz not every frame has valid receive data, so the ratio |
| * between pcm data and GPIO status data changes. Our FIQ handler is not |
| * able to handle this, hence this driver only works with 48000Hz sampling |
| * rate. |
| * Reading and writing AC97 registers is another challenge. The core |
| * provides us status bits when the read register is updated with *another* |
| * value. When we read the same register two times (and the register still |
| * contains the same value) these status bits are not set. We work |
| * around this by not polling these bits but only wait a fixed delay. |
| * |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/device.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/init.h> |
| #include <linux/interrupt.h> |
| #include <linux/module.h> |
| #include <linux/platform_device.h> |
| #include <linux/slab.h> |
| |
| #include <sound/core.h> |
| #include <sound/initval.h> |
| #include <sound/pcm.h> |
| #include <sound/pcm_params.h> |
| #include <sound/soc.h> |
| |
| #include <linux/platform_data/asoc-imx-ssi.h> |
| |
| #include "imx-ssi.h" |
| #include "fsl_utils.h" |
| |
| #define SSI_SACNT_DEFAULT (SSI_SACNT_AC97EN | SSI_SACNT_FV) |
| |
| /* |
| * SSI Network Mode or TDM slots configuration. |
| * Should only be called when port is inactive (i.e. SSIEN = 0). |
| */ |
| static int imx_ssi_set_dai_tdm_slot(struct snd_soc_dai *cpu_dai, |
| unsigned int tx_mask, unsigned int rx_mask, int slots, int slot_width) |
| { |
| struct imx_ssi *ssi = snd_soc_dai_get_drvdata(cpu_dai); |
| u32 sccr; |
| |
| sccr = readl(ssi->base + SSI_STCCR); |
| sccr &= ~SSI_STCCR_DC_MASK; |
| sccr |= SSI_STCCR_DC(slots - 1); |
| writel(sccr, ssi->base + SSI_STCCR); |
| |
| sccr = readl(ssi->base + SSI_SRCCR); |
| sccr &= ~SSI_STCCR_DC_MASK; |
| sccr |= SSI_STCCR_DC(slots - 1); |
| writel(sccr, ssi->base + SSI_SRCCR); |
| |
| writel(~tx_mask, ssi->base + SSI_STMSK); |
| writel(~rx_mask, ssi->base + SSI_SRMSK); |
| |
| return 0; |
| } |
| |
| /* |
| * SSI DAI format configuration. |
| * Should only be called when port is inactive (i.e. SSIEN = 0). |
| */ |
| static int imx_ssi_set_dai_fmt(struct snd_soc_dai *cpu_dai, unsigned int fmt) |
| { |
| struct imx_ssi *ssi = snd_soc_dai_get_drvdata(cpu_dai); |
| u32 strcr = 0, scr; |
| |
| scr = readl(ssi->base + SSI_SCR) & ~(SSI_SCR_SYN | SSI_SCR_NET); |
| |
| /* DAI mode */ |
| switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { |
| case SND_SOC_DAIFMT_I2S: |
| /* data on rising edge of bclk, frame low 1clk before data */ |
| strcr |= SSI_STCR_TFSI | SSI_STCR_TEFS | SSI_STCR_TXBIT0; |
| scr |= SSI_SCR_NET; |
| if (ssi->flags & IMX_SSI_USE_I2S_SLAVE) { |
| scr &= ~SSI_I2S_MODE_MASK; |
| scr |= SSI_SCR_I2S_MODE_SLAVE; |
| } |
| break; |
| case SND_SOC_DAIFMT_LEFT_J: |
| /* data on rising edge of bclk, frame high with data */ |
| strcr |= SSI_STCR_TXBIT0; |
| break; |
| case SND_SOC_DAIFMT_DSP_B: |
| /* data on rising edge of bclk, frame high with data */ |
| strcr |= SSI_STCR_TFSL | SSI_STCR_TXBIT0; |
| break; |
| case SND_SOC_DAIFMT_DSP_A: |
| /* data on rising edge of bclk, frame high 1clk before data */ |
| strcr |= SSI_STCR_TFSL | SSI_STCR_TXBIT0 | SSI_STCR_TEFS; |
| break; |
| } |
| |
| /* DAI clock inversion */ |
| switch (fmt & SND_SOC_DAIFMT_INV_MASK) { |
| case SND_SOC_DAIFMT_IB_IF: |
| strcr |= SSI_STCR_TFSI; |
| strcr &= ~SSI_STCR_TSCKP; |
| break; |
| case SND_SOC_DAIFMT_IB_NF: |
| strcr &= ~(SSI_STCR_TSCKP | SSI_STCR_TFSI); |
| break; |
| case SND_SOC_DAIFMT_NB_IF: |
| strcr |= SSI_STCR_TFSI | SSI_STCR_TSCKP; |
| break; |
| case SND_SOC_DAIFMT_NB_NF: |
| strcr &= ~SSI_STCR_TFSI; |
| strcr |= SSI_STCR_TSCKP; |
| break; |
| } |
| |
| /* DAI clock master masks */ |
| switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { |
| case SND_SOC_DAIFMT_CBM_CFM: |
| break; |
| default: |
| /* Master mode not implemented, needs handling of clocks. */ |
| return -EINVAL; |
| } |
| |
| strcr |= SSI_STCR_TFEN0; |
| |
| if (ssi->flags & IMX_SSI_NET) |
| scr |= SSI_SCR_NET; |
| if (ssi->flags & IMX_SSI_SYN) |
| scr |= SSI_SCR_SYN; |
| |
| writel(strcr, ssi->base + SSI_STCR); |
| writel(strcr, ssi->base + SSI_SRCR); |
| writel(scr, ssi->base + SSI_SCR); |
| |
| return 0; |
| } |
| |
| /* |
| * SSI system clock configuration. |
| * Should only be called when port is inactive (i.e. SSIEN = 0). |
| */ |
| static int imx_ssi_set_dai_sysclk(struct snd_soc_dai *cpu_dai, |
| int clk_id, unsigned int freq, int dir) |
| { |
| struct imx_ssi *ssi = snd_soc_dai_get_drvdata(cpu_dai); |
| u32 scr; |
| |
| scr = readl(ssi->base + SSI_SCR); |
| |
| switch (clk_id) { |
| case IMX_SSP_SYS_CLK: |
| if (dir == SND_SOC_CLOCK_OUT) |
| scr |= SSI_SCR_SYS_CLK_EN; |
| else |
| scr &= ~SSI_SCR_SYS_CLK_EN; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| writel(scr, ssi->base + SSI_SCR); |
| |
| return 0; |
| } |
| |
| /* |
| * SSI Clock dividers |
| * Should only be called when port is inactive (i.e. SSIEN = 0). |
| */ |
| static int imx_ssi_set_dai_clkdiv(struct snd_soc_dai *cpu_dai, |
| int div_id, int div) |
| { |
| struct imx_ssi *ssi = snd_soc_dai_get_drvdata(cpu_dai); |
| u32 stccr, srccr; |
| |
| stccr = readl(ssi->base + SSI_STCCR); |
| srccr = readl(ssi->base + SSI_SRCCR); |
| |
| switch (div_id) { |
| case IMX_SSI_TX_DIV_2: |
| stccr &= ~SSI_STCCR_DIV2; |
| stccr |= div; |
| break; |
| case IMX_SSI_TX_DIV_PSR: |
| stccr &= ~SSI_STCCR_PSR; |
| stccr |= div; |
| break; |
| case IMX_SSI_TX_DIV_PM: |
| stccr &= ~0xff; |
| stccr |= SSI_STCCR_PM(div); |
| break; |
| case IMX_SSI_RX_DIV_2: |
| stccr &= ~SSI_STCCR_DIV2; |
| stccr |= div; |
| break; |
| case IMX_SSI_RX_DIV_PSR: |
| stccr &= ~SSI_STCCR_PSR; |
| stccr |= div; |
| break; |
| case IMX_SSI_RX_DIV_PM: |
| stccr &= ~0xff; |
| stccr |= SSI_STCCR_PM(div); |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| writel(stccr, ssi->base + SSI_STCCR); |
| writel(srccr, ssi->base + SSI_SRCCR); |
| |
| return 0; |
| } |
| |
| /* |
| * Should only be called when port is inactive (i.e. SSIEN = 0), |
| * although can be called multiple times by upper layers. |
| */ |
| static int imx_ssi_hw_params(struct snd_pcm_substream *substream, |
| struct snd_pcm_hw_params *params, |
| struct snd_soc_dai *cpu_dai) |
| { |
| struct imx_ssi *ssi = snd_soc_dai_get_drvdata(cpu_dai); |
| u32 reg, sccr; |
| |
| /* Tx/Rx config */ |
| if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) |
| reg = SSI_STCCR; |
| else |
| reg = SSI_SRCCR; |
| |
| if (ssi->flags & IMX_SSI_SYN) |
| reg = SSI_STCCR; |
| |
| sccr = readl(ssi->base + reg) & ~SSI_STCCR_WL_MASK; |
| |
| /* DAI data (word) size */ |
| switch (params_format(params)) { |
| case SNDRV_PCM_FORMAT_S16_LE: |
| sccr |= SSI_SRCCR_WL(16); |
| break; |
| case SNDRV_PCM_FORMAT_S20_3LE: |
| sccr |= SSI_SRCCR_WL(20); |
| break; |
| case SNDRV_PCM_FORMAT_S24_LE: |
| sccr |= SSI_SRCCR_WL(24); |
| break; |
| } |
| |
| writel(sccr, ssi->base + reg); |
| |
| return 0; |
| } |
| |
| static int imx_ssi_trigger(struct snd_pcm_substream *substream, int cmd, |
| struct snd_soc_dai *dai) |
| { |
| struct imx_ssi *ssi = snd_soc_dai_get_drvdata(dai); |
| unsigned int sier_bits, sier; |
| unsigned int scr; |
| |
| scr = readl(ssi->base + SSI_SCR); |
| sier = readl(ssi->base + SSI_SIER); |
| |
| if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { |
| if (ssi->flags & IMX_SSI_DMA) |
| sier_bits = SSI_SIER_TDMAE; |
| else |
| sier_bits = SSI_SIER_TIE | SSI_SIER_TFE0_EN; |
| } else { |
| if (ssi->flags & IMX_SSI_DMA) |
| sier_bits = SSI_SIER_RDMAE; |
| else |
| sier_bits = SSI_SIER_RIE | SSI_SIER_RFF0_EN; |
| } |
| |
| switch (cmd) { |
| case SNDRV_PCM_TRIGGER_START: |
| case SNDRV_PCM_TRIGGER_RESUME: |
| case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: |
| if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) |
| scr |= SSI_SCR_TE; |
| else |
| scr |= SSI_SCR_RE; |
| sier |= sier_bits; |
| |
| scr |= SSI_SCR_SSIEN; |
| |
| break; |
| |
| case SNDRV_PCM_TRIGGER_STOP: |
| case SNDRV_PCM_TRIGGER_SUSPEND: |
| case SNDRV_PCM_TRIGGER_PAUSE_PUSH: |
| if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) |
| scr &= ~SSI_SCR_TE; |
| else |
| scr &= ~SSI_SCR_RE; |
| sier &= ~sier_bits; |
| |
| if (!(scr & (SSI_SCR_TE | SSI_SCR_RE))) |
| scr &= ~SSI_SCR_SSIEN; |
| |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| if (!(ssi->flags & IMX_SSI_USE_AC97)) |
| /* rx/tx are always enabled to access ac97 registers */ |
| writel(scr, ssi->base + SSI_SCR); |
| |
| writel(sier, ssi->base + SSI_SIER); |
| |
| return 0; |
| } |
| |
| static const struct snd_soc_dai_ops imx_ssi_pcm_dai_ops = { |
| .hw_params = imx_ssi_hw_params, |
| .set_fmt = imx_ssi_set_dai_fmt, |
| .set_clkdiv = imx_ssi_set_dai_clkdiv, |
| .set_sysclk = imx_ssi_set_dai_sysclk, |
| .set_tdm_slot = imx_ssi_set_dai_tdm_slot, |
| .trigger = imx_ssi_trigger, |
| }; |
| |
| static int imx_ssi_dai_probe(struct snd_soc_dai *dai) |
| { |
| struct imx_ssi *ssi = dev_get_drvdata(dai->dev); |
| uint32_t val; |
| |
| snd_soc_dai_set_drvdata(dai, ssi); |
| |
| val = SSI_SFCSR_TFWM0(ssi->dma_params_tx.maxburst) | |
| SSI_SFCSR_RFWM0(ssi->dma_params_rx.maxburst); |
| writel(val, ssi->base + SSI_SFCSR); |
| |
| /* Tx/Rx config */ |
| dai->playback_dma_data = &ssi->dma_params_tx; |
| dai->capture_dma_data = &ssi->dma_params_rx; |
| |
| return 0; |
| } |
| |
| static struct snd_soc_dai_driver imx_ssi_dai = { |
| .probe = imx_ssi_dai_probe, |
| .playback = { |
| .channels_min = 1, |
| .channels_max = 2, |
| .rates = SNDRV_PCM_RATE_8000_96000, |
| .formats = SNDRV_PCM_FMTBIT_S16_LE, |
| }, |
| .capture = { |
| .channels_min = 1, |
| .channels_max = 2, |
| .rates = SNDRV_PCM_RATE_8000_96000, |
| .formats = SNDRV_PCM_FMTBIT_S16_LE, |
| }, |
| .ops = &imx_ssi_pcm_dai_ops, |
| }; |
| |
| static struct snd_soc_dai_driver imx_ac97_dai = { |
| .probe = imx_ssi_dai_probe, |
| .bus_control = true, |
| .playback = { |
| .stream_name = "AC97 Playback", |
| .channels_min = 2, |
| .channels_max = 2, |
| .rates = SNDRV_PCM_RATE_8000_48000, |
| .formats = SNDRV_PCM_FMTBIT_S16_LE, |
| }, |
| .capture = { |
| .stream_name = "AC97 Capture", |
| .channels_min = 2, |
| .channels_max = 2, |
| .rates = SNDRV_PCM_RATE_48000, |
| .formats = SNDRV_PCM_FMTBIT_S16_LE, |
| }, |
| .ops = &imx_ssi_pcm_dai_ops, |
| }; |
| |
| static const struct snd_soc_component_driver imx_component = { |
| .name = DRV_NAME, |
| }; |
| |
| static void setup_channel_to_ac97(struct imx_ssi *imx_ssi) |
| { |
| void __iomem *base = imx_ssi->base; |
| |
| writel(0x0, base + SSI_SCR); |
| writel(0x0, base + SSI_STCR); |
| writel(0x0, base + SSI_SRCR); |
| |
| writel(SSI_SCR_SYN | SSI_SCR_NET, base + SSI_SCR); |
| |
| writel(SSI_SFCSR_RFWM0(8) | |
| SSI_SFCSR_TFWM0(8) | |
| SSI_SFCSR_RFWM1(8) | |
| SSI_SFCSR_TFWM1(8), base + SSI_SFCSR); |
| |
| writel(SSI_STCCR_WL(16) | SSI_STCCR_DC(12), base + SSI_STCCR); |
| writel(SSI_STCCR_WL(16) | SSI_STCCR_DC(12), base + SSI_SRCCR); |
| |
| writel(SSI_SCR_SYN | SSI_SCR_NET | SSI_SCR_SSIEN, base + SSI_SCR); |
| writel(SSI_SOR_WAIT(3), base + SSI_SOR); |
| |
| writel(SSI_SCR_SYN | SSI_SCR_NET | SSI_SCR_SSIEN | |
| SSI_SCR_TE | SSI_SCR_RE, |
| base + SSI_SCR); |
| |
| writel(SSI_SACNT_DEFAULT, base + SSI_SACNT); |
| writel(0xff, base + SSI_SACCDIS); |
| writel(0x300, base + SSI_SACCEN); |
| } |
| |
| static struct imx_ssi *ac97_ssi; |
| |
| static void imx_ssi_ac97_write(struct snd_ac97 *ac97, unsigned short reg, |
| unsigned short val) |
| { |
| struct imx_ssi *imx_ssi = ac97_ssi; |
| void __iomem *base = imx_ssi->base; |
| unsigned int lreg; |
| unsigned int lval; |
| |
| if (reg > 0x7f) |
| return; |
| |
| pr_debug("%s: 0x%02x 0x%04x\n", __func__, reg, val); |
| |
| lreg = reg << 12; |
| writel(lreg, base + SSI_SACADD); |
| |
| lval = val << 4; |
| writel(lval , base + SSI_SACDAT); |
| |
| writel(SSI_SACNT_DEFAULT | SSI_SACNT_WR, base + SSI_SACNT); |
| udelay(100); |
| } |
| |
| static unsigned short imx_ssi_ac97_read(struct snd_ac97 *ac97, |
| unsigned short reg) |
| { |
| struct imx_ssi *imx_ssi = ac97_ssi; |
| void __iomem *base = imx_ssi->base; |
| |
| unsigned short val = -1; |
| unsigned int lreg; |
| |
| lreg = (reg & 0x7f) << 12 ; |
| writel(lreg, base + SSI_SACADD); |
| writel(SSI_SACNT_DEFAULT | SSI_SACNT_RD, base + SSI_SACNT); |
| |
| udelay(100); |
| |
| val = (readl(base + SSI_SACDAT) >> 4) & 0xffff; |
| |
| pr_debug("%s: 0x%02x 0x%04x\n", __func__, reg, val); |
| |
| return val; |
| } |
| |
| static void imx_ssi_ac97_reset(struct snd_ac97 *ac97) |
| { |
| struct imx_ssi *imx_ssi = ac97_ssi; |
| |
| if (imx_ssi->ac97_reset) |
| imx_ssi->ac97_reset(ac97); |
| /* First read sometimes fails, do a dummy read */ |
| imx_ssi_ac97_read(ac97, 0); |
| } |
| |
| static void imx_ssi_ac97_warm_reset(struct snd_ac97 *ac97) |
| { |
| struct imx_ssi *imx_ssi = ac97_ssi; |
| |
| if (imx_ssi->ac97_warm_reset) |
| imx_ssi->ac97_warm_reset(ac97); |
| |
| /* First read sometimes fails, do a dummy read */ |
| imx_ssi_ac97_read(ac97, 0); |
| } |
| |
| static struct snd_ac97_bus_ops imx_ssi_ac97_ops = { |
| .read = imx_ssi_ac97_read, |
| .write = imx_ssi_ac97_write, |
| .reset = imx_ssi_ac97_reset, |
| .warm_reset = imx_ssi_ac97_warm_reset |
| }; |
| |
| static int imx_ssi_probe(struct platform_device *pdev) |
| { |
| struct resource *res; |
| struct imx_ssi *ssi; |
| struct imx_ssi_platform_data *pdata = pdev->dev.platform_data; |
| int ret = 0; |
| struct snd_soc_dai_driver *dai; |
| |
| ssi = devm_kzalloc(&pdev->dev, sizeof(*ssi), GFP_KERNEL); |
| if (!ssi) |
| return -ENOMEM; |
| dev_set_drvdata(&pdev->dev, ssi); |
| |
| if (pdata) { |
| ssi->ac97_reset = pdata->ac97_reset; |
| ssi->ac97_warm_reset = pdata->ac97_warm_reset; |
| ssi->flags = pdata->flags; |
| } |
| |
| ssi->irq = platform_get_irq(pdev, 0); |
| |
| ssi->clk = devm_clk_get(&pdev->dev, NULL); |
| if (IS_ERR(ssi->clk)) { |
| ret = PTR_ERR(ssi->clk); |
| dev_err(&pdev->dev, "Cannot get the clock: %d\n", |
| ret); |
| goto failed_clk; |
| } |
| ret = clk_prepare_enable(ssi->clk); |
| if (ret) |
| goto failed_clk; |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| ssi->base = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(ssi->base)) { |
| ret = PTR_ERR(ssi->base); |
| goto failed_register; |
| } |
| |
| if (ssi->flags & IMX_SSI_USE_AC97) { |
| if (ac97_ssi) { |
| dev_err(&pdev->dev, "AC'97 SSI already registered\n"); |
| ret = -EBUSY; |
| goto failed_register; |
| } |
| ac97_ssi = ssi; |
| setup_channel_to_ac97(ssi); |
| dai = &imx_ac97_dai; |
| } else |
| dai = &imx_ssi_dai; |
| |
| writel(0x0, ssi->base + SSI_SIER); |
| |
| ssi->dma_params_rx.addr = res->start + SSI_SRX0; |
| ssi->dma_params_tx.addr = res->start + SSI_STX0; |
| |
| ssi->dma_params_tx.maxburst = 6; |
| ssi->dma_params_rx.maxburst = 4; |
| |
| ssi->dma_params_tx.filter_data = &ssi->filter_data_tx; |
| ssi->dma_params_rx.filter_data = &ssi->filter_data_rx; |
| |
| res = platform_get_resource_byname(pdev, IORESOURCE_DMA, "tx0"); |
| if (res) { |
| imx_pcm_dma_params_init_data(&ssi->filter_data_tx, res->start, |
| IMX_DMATYPE_SSI); |
| } |
| |
| res = platform_get_resource_byname(pdev, IORESOURCE_DMA, "rx0"); |
| if (res) { |
| imx_pcm_dma_params_init_data(&ssi->filter_data_rx, res->start, |
| IMX_DMATYPE_SSI); |
| } |
| |
| platform_set_drvdata(pdev, ssi); |
| |
| ret = snd_soc_set_ac97_ops(&imx_ssi_ac97_ops); |
| if (ret != 0) { |
| dev_err(&pdev->dev, "Failed to set AC'97 ops: %d\n", ret); |
| goto failed_register; |
| } |
| |
| ret = snd_soc_register_component(&pdev->dev, &imx_component, |
| dai, 1); |
| if (ret) { |
| dev_err(&pdev->dev, "register DAI failed\n"); |
| goto failed_register; |
| } |
| |
| ssi->fiq_params.irq = ssi->irq; |
| ssi->fiq_params.base = ssi->base; |
| ssi->fiq_params.dma_params_rx = &ssi->dma_params_rx; |
| ssi->fiq_params.dma_params_tx = &ssi->dma_params_tx; |
| |
| ssi->fiq_init = imx_pcm_fiq_init(pdev, &ssi->fiq_params); |
| ssi->dma_init = imx_pcm_dma_init(pdev); |
| |
| if (ssi->fiq_init && ssi->dma_init) { |
| ret = ssi->fiq_init; |
| goto failed_pcm; |
| } |
| |
| return 0; |
| |
| failed_pcm: |
| snd_soc_unregister_component(&pdev->dev); |
| failed_register: |
| clk_disable_unprepare(ssi->clk); |
| failed_clk: |
| snd_soc_set_ac97_ops(NULL); |
| |
| return ret; |
| } |
| |
| static int imx_ssi_remove(struct platform_device *pdev) |
| { |
| struct imx_ssi *ssi = platform_get_drvdata(pdev); |
| |
| if (!ssi->fiq_init) |
| imx_pcm_fiq_exit(pdev); |
| |
| snd_soc_unregister_component(&pdev->dev); |
| |
| if (ssi->flags & IMX_SSI_USE_AC97) |
| ac97_ssi = NULL; |
| |
| clk_disable_unprepare(ssi->clk); |
| snd_soc_set_ac97_ops(NULL); |
| |
| return 0; |
| } |
| |
| static struct platform_driver imx_ssi_driver = { |
| .probe = imx_ssi_probe, |
| .remove = imx_ssi_remove, |
| |
| .driver = { |
| .name = "imx-ssi", |
| }, |
| }; |
| |
| module_platform_driver(imx_ssi_driver); |
| |
| /* Module information */ |
| MODULE_AUTHOR("Sascha Hauer, <s.hauer@pengutronix.de>"); |
| MODULE_DESCRIPTION("i.MX I2S/ac97 SoC Interface"); |
| MODULE_LICENSE("GPL"); |
| MODULE_ALIAS("platform:imx-ssi"); |