| /* |
| * Copyright (c) 2010 Broadcom Corporation |
| * |
| * Permission to use, copy, modify, and/or distribute this software for any |
| * purpose with or without fee is hereby granted, provided that the above |
| * copyright notice and this permission notice appear in all copies. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY |
| * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION |
| * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN |
| * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
| */ |
| |
| #ifndef _BRCM_SDH_H_ |
| #define _BRCM_SDH_H_ |
| |
| #include <linux/skbuff.h> |
| |
| #define SDIO_FUNC_0 0 |
| #define SDIO_FUNC_1 1 |
| #define SDIO_FUNC_2 2 |
| |
| #define SDIOD_FBR_SIZE 0x100 |
| |
| /* io_en */ |
| #define SDIO_FUNC_ENABLE_1 0x02 |
| #define SDIO_FUNC_ENABLE_2 0x04 |
| |
| /* io_rdys */ |
| #define SDIO_FUNC_READY_1 0x02 |
| #define SDIO_FUNC_READY_2 0x04 |
| |
| /* intr_status */ |
| #define INTR_STATUS_FUNC1 0x2 |
| #define INTR_STATUS_FUNC2 0x4 |
| |
| /* Maximum number of I/O funcs */ |
| #define SDIOD_MAX_IOFUNCS 7 |
| |
| /* mask of register map */ |
| #define REG_F0_REG_MASK 0x7FF |
| #define REG_F1_MISC_MASK 0x1FFFF |
| |
| /* as of sdiod rev 0, supports 3 functions */ |
| #define SBSDIO_NUM_FUNCTION 3 |
| |
| /* function 0 vendor specific CCCR registers */ |
| #define SDIO_CCCR_BRCM_CARDCAP 0xf0 |
| #define SDIO_CCCR_BRCM_CARDCAP_CMD14_SUPPORT 0x02 |
| #define SDIO_CCCR_BRCM_CARDCAP_CMD14_EXT 0x04 |
| #define SDIO_CCCR_BRCM_CARDCAP_CMD_NODEC 0x08 |
| #define SDIO_CCCR_BRCM_CARDCTRL 0xf1 |
| #define SDIO_CCCR_BRCM_CARDCTRL_WLANRESET 0x02 |
| #define SDIO_CCCR_BRCM_SEPINT 0xf2 |
| |
| #define SDIO_SEPINT_MASK 0x01 |
| #define SDIO_SEPINT_OE 0x02 |
| #define SDIO_SEPINT_ACT_HI 0x04 |
| |
| /* function 1 miscellaneous registers */ |
| |
| /* sprom command and status */ |
| #define SBSDIO_SPROM_CS 0x10000 |
| /* sprom info register */ |
| #define SBSDIO_SPROM_INFO 0x10001 |
| /* sprom indirect access data byte 0 */ |
| #define SBSDIO_SPROM_DATA_LOW 0x10002 |
| /* sprom indirect access data byte 1 */ |
| #define SBSDIO_SPROM_DATA_HIGH 0x10003 |
| /* sprom indirect access addr byte 0 */ |
| #define SBSDIO_SPROM_ADDR_LOW 0x10004 |
| /* sprom indirect access addr byte 0 */ |
| #define SBSDIO_SPROM_ADDR_HIGH 0x10005 |
| /* xtal_pu (gpio) output */ |
| #define SBSDIO_CHIP_CTRL_DATA 0x10006 |
| /* xtal_pu (gpio) enable */ |
| #define SBSDIO_CHIP_CTRL_EN 0x10007 |
| /* rev < 7, watermark for sdio device */ |
| #define SBSDIO_WATERMARK 0x10008 |
| /* control busy signal generation */ |
| #define SBSDIO_DEVICE_CTL 0x10009 |
| |
| /* SB Address Window Low (b15) */ |
| #define SBSDIO_FUNC1_SBADDRLOW 0x1000A |
| /* SB Address Window Mid (b23:b16) */ |
| #define SBSDIO_FUNC1_SBADDRMID 0x1000B |
| /* SB Address Window High (b31:b24) */ |
| #define SBSDIO_FUNC1_SBADDRHIGH 0x1000C |
| /* Frame Control (frame term/abort) */ |
| #define SBSDIO_FUNC1_FRAMECTRL 0x1000D |
| /* ChipClockCSR (ALP/HT ctl/status) */ |
| #define SBSDIO_FUNC1_CHIPCLKCSR 0x1000E |
| /* SdioPullUp (on cmd, d0-d2) */ |
| #define SBSDIO_FUNC1_SDIOPULLUP 0x1000F |
| /* Write Frame Byte Count Low */ |
| #define SBSDIO_FUNC1_WFRAMEBCLO 0x10019 |
| /* Write Frame Byte Count High */ |
| #define SBSDIO_FUNC1_WFRAMEBCHI 0x1001A |
| /* Read Frame Byte Count Low */ |
| #define SBSDIO_FUNC1_RFRAMEBCLO 0x1001B |
| /* Read Frame Byte Count High */ |
| #define SBSDIO_FUNC1_RFRAMEBCHI 0x1001C |
| /* MesBusyCtl (rev 11) */ |
| #define SBSDIO_FUNC1_MESBUSYCTRL 0x1001D |
| /* Sdio Core Rev 12 */ |
| #define SBSDIO_FUNC1_WAKEUPCTRL 0x1001E |
| #define SBSDIO_FUNC1_WCTRL_ALPWAIT_MASK 0x1 |
| #define SBSDIO_FUNC1_WCTRL_ALPWAIT_SHIFT 0 |
| #define SBSDIO_FUNC1_WCTRL_HTWAIT_MASK 0x2 |
| #define SBSDIO_FUNC1_WCTRL_HTWAIT_SHIFT 1 |
| #define SBSDIO_FUNC1_SLEEPCSR 0x1001F |
| #define SBSDIO_FUNC1_SLEEPCSR_KSO_MASK 0x1 |
| #define SBSDIO_FUNC1_SLEEPCSR_KSO_SHIFT 0 |
| #define SBSDIO_FUNC1_SLEEPCSR_KSO_EN 1 |
| #define SBSDIO_FUNC1_SLEEPCSR_DEVON_MASK 0x2 |
| #define SBSDIO_FUNC1_SLEEPCSR_DEVON_SHIFT 1 |
| |
| #define SBSDIO_FUNC1_MISC_REG_START 0x10000 /* f1 misc register start */ |
| #define SBSDIO_FUNC1_MISC_REG_LIMIT 0x1001F /* f1 misc register end */ |
| |
| /* function 1 OCP space */ |
| |
| /* sb offset addr is <= 15 bits, 32k */ |
| #define SBSDIO_SB_OFT_ADDR_MASK 0x07FFF |
| #define SBSDIO_SB_OFT_ADDR_LIMIT 0x08000 |
| /* with b15, maps to 32-bit SB access */ |
| #define SBSDIO_SB_ACCESS_2_4B_FLAG 0x08000 |
| |
| /* valid bits in SBSDIO_FUNC1_SBADDRxxx regs */ |
| |
| #define SBSDIO_SBADDRLOW_MASK 0x80 /* Valid bits in SBADDRLOW */ |
| #define SBSDIO_SBADDRMID_MASK 0xff /* Valid bits in SBADDRMID */ |
| #define SBSDIO_SBADDRHIGH_MASK 0xffU /* Valid bits in SBADDRHIGH */ |
| /* Address bits from SBADDR regs */ |
| #define SBSDIO_SBWINDOW_MASK 0xffff8000 |
| |
| #define SDIOH_READ 0 /* Read request */ |
| #define SDIOH_WRITE 1 /* Write request */ |
| |
| #define SDIOH_DATA_FIX 0 /* Fixed addressing */ |
| #define SDIOH_DATA_INC 1 /* Incremental addressing */ |
| |
| /* internal return code */ |
| #define SUCCESS 0 |
| #define ERROR 1 |
| |
| /* Packet alignment for most efficient SDIO (can change based on platform) */ |
| #define BRCMF_SDALIGN (1 << 6) |
| |
| /* watchdog polling interval in ms */ |
| #define BRCMF_WD_POLL_MS 10 |
| |
| struct brcmf_sdreg { |
| int func; |
| int offset; |
| int value; |
| }; |
| |
| struct brcmf_sdio; |
| |
| struct brcmf_sdio_dev { |
| struct sdio_func *func[SDIO_MAX_FUNCS]; |
| u8 num_funcs; /* Supported funcs on client */ |
| u32 sbwad; /* Save backplane window address */ |
| void *bus; |
| atomic_t suspend; /* suspend flag */ |
| wait_queue_head_t request_byte_wait; |
| wait_queue_head_t request_word_wait; |
| wait_queue_head_t request_buffer_wait; |
| struct device *dev; |
| struct brcmf_bus *bus_if; |
| struct brcmfmac_sdio_platform_data *pdata; |
| bool oob_irq_requested; |
| bool irq_en; /* irq enable flags */ |
| spinlock_t irq_en_lock; |
| bool irq_wake; /* irq wake enable flags */ |
| bool sg_support; |
| uint max_request_size; |
| ushort max_segment_count; |
| uint max_segment_size; |
| }; |
| |
| /* Register/deregister interrupt handler. */ |
| int brcmf_sdio_intr_register(struct brcmf_sdio_dev *sdiodev); |
| int brcmf_sdio_intr_unregister(struct brcmf_sdio_dev *sdiodev); |
| |
| /* sdio device register access interface */ |
| u8 brcmf_sdio_regrb(struct brcmf_sdio_dev *sdiodev, u32 addr, int *ret); |
| u32 brcmf_sdio_regrl(struct brcmf_sdio_dev *sdiodev, u32 addr, int *ret); |
| void brcmf_sdio_regwb(struct brcmf_sdio_dev *sdiodev, u32 addr, u8 data, |
| int *ret); |
| void brcmf_sdio_regwl(struct brcmf_sdio_dev *sdiodev, u32 addr, u32 data, |
| int *ret); |
| |
| /* Buffer transfer to/from device (client) core via cmd53. |
| * fn: function number |
| * addr: backplane address (i.e. >= regsva from attach) |
| * flags: backplane width, address increment, sync/async |
| * buf: pointer to memory data buffer |
| * nbytes: number of bytes to transfer to/from buf |
| * pkt: pointer to packet associated with buf (if any) |
| * complete: callback function for command completion (async only) |
| * handle: handle for completion callback (first arg in callback) |
| * Returns 0 or error code. |
| * NOTE: Async operation is not currently supported. |
| */ |
| int brcmf_sdcard_send_pkt(struct brcmf_sdio_dev *sdiodev, u32 addr, uint fn, |
| uint flags, struct sk_buff_head *pktq); |
| int brcmf_sdcard_send_buf(struct brcmf_sdio_dev *sdiodev, u32 addr, uint fn, |
| uint flags, u8 *buf, uint nbytes); |
| |
| int brcmf_sdcard_recv_pkt(struct brcmf_sdio_dev *sdiodev, u32 addr, uint fn, |
| uint flags, struct sk_buff *pkt); |
| int brcmf_sdcard_recv_buf(struct brcmf_sdio_dev *sdiodev, u32 addr, uint fn, |
| uint flags, u8 *buf, uint nbytes); |
| int brcmf_sdcard_recv_chain(struct brcmf_sdio_dev *sdiodev, u32 addr, uint fn, |
| uint flags, struct sk_buff_head *pktq, uint totlen); |
| |
| /* Flags bits */ |
| |
| /* Four-byte target (backplane) width (vs. two-byte) */ |
| #define SDIO_REQ_4BYTE 0x1 |
| /* Fixed address (FIFO) (vs. incrementing address) */ |
| #define SDIO_REQ_FIXED 0x2 |
| |
| /* Read/write to memory block (F1, no FIFO) via CMD53 (sync only). |
| * rw: read or write (0/1) |
| * addr: direct SDIO address |
| * buf: pointer to memory data buffer |
| * nbytes: number of bytes to transfer to/from buf |
| * Returns 0 or error code. |
| */ |
| int brcmf_sdio_ramrw(struct brcmf_sdio_dev *sdiodev, bool write, u32 address, |
| u8 *data, uint size); |
| |
| /* Issue an abort to the specified function */ |
| int brcmf_sdcard_abort(struct brcmf_sdio_dev *sdiodev, uint fn); |
| |
| void *brcmf_sdbrcm_probe(u32 regsva, struct brcmf_sdio_dev *sdiodev); |
| void brcmf_sdbrcm_disconnect(void *ptr); |
| void brcmf_sdbrcm_isr(void *arg); |
| |
| void brcmf_sdbrcm_wd_timer(struct brcmf_sdio *bus, uint wdtick); |
| |
| #endif /* _BRCM_SDH_H_ */ |