Device tree aware EMAC driver
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs. The
same ASIC is also found in the Axon bridge chip. This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging. Specifically:
- Should be adjusted to properly use the dma mapping API.
Axon needs this.
- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices. The dependencies here between
EMAC, MAL, ZMII etc. make this complicated. At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/ibm_newemac/Kconfig b/drivers/net/ibm_newemac/Kconfig
new file mode 100644
index 0000000..0d3e738
--- /dev/null
+++ b/drivers/net/ibm_newemac/Kconfig
@@ -0,0 +1,63 @@
+config IBM_NEW_EMAC
+ tristate "IBM EMAC Ethernet support"
+ depends on PPC_DCR && PPC_MERGE
+ help
+ This driver supports the IBM EMAC family of Ethernet controllers
+ typically found on 4xx embedded PowerPC chips, but also on the
+ Axon southbridge for Cell.
+
+config IBM_NEW_EMAC_RXB
+ int "Number of receive buffers"
+ depends on IBM_NEW_EMAC
+ default "128"
+
+config IBM_NEW_EMAC_TXB
+ int "Number of transmit buffers"
+ depends on IBM_NEW_EMAC
+ default "64"
+
+config IBM_NEW_EMAC_POLL_WEIGHT
+ int "MAL NAPI polling weight"
+ depends on IBM_NEW_EMAC
+ default "32"
+
+config IBM_NEW_EMAC_RX_COPY_THRESHOLD
+ int "RX skb copy threshold (bytes)"
+ depends on IBM_NEW_EMAC
+ default "256"
+
+config IBM_NEW_EMAC_RX_SKB_HEADROOM
+ int "Additional RX skb headroom (bytes)"
+ depends on IBM_NEW_EMAC
+ default "0"
+ help
+ Additional receive skb headroom. Note, that driver
+ will always reserve at least 2 bytes to make IP header
+ aligned, so usually there is no need to add any additional
+ headroom.
+
+ If unsure, set to 0.
+
+config IBM_NEW_EMAC_DEBUG
+ bool "Debugging"
+ depends on IBM_NEW_EMAC
+ default n
+
+# The options below has to be select'ed by the respective
+# processor types or platforms
+
+config IBM_NEW_EMAC_ZMII
+ bool
+ default n
+
+config IBM_NEW_EMAC_RGMII
+ bool
+ default n
+
+config IBM_NEW_EMAC_TAH
+ bool
+ default n
+
+config IBM_NEW_EMAC_EMAC4
+ bool
+ default n