Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/Documentation/sound/alsa/serial-u16550.txt b/Documentation/sound/alsa/serial-u16550.txt
new file mode 100644
index 0000000..c191955
--- /dev/null
+++ b/Documentation/sound/alsa/serial-u16550.txt
@@ -0,0 +1,88 @@
+
+ Serial UART 16450/16550 MIDI driver
+ ===================================
+
+The adaptor module parameter allows you to select either:
+
+ 0 - Roland Soundcanvas support (default)
+ 1 - Midiator MS-124T support (1)
+ 2 - Midiator MS-124W S/A mode (2)
+ 3 - MS-124W M/B mode support (3)
+ 4 - Generic device with multiple input support (4)
+
+For the Midiator MS-124W, you must set the physical M-S and A-B
+switches on the Midiator to match the driver mode you select.
+
+In Roland Soundcanvas mode, multiple ALSA raw MIDI substreams are supported
+(midiCnD0-midiCnD15). Whenever you write to a different substream, the driver
+sends the nonstandard MIDI command sequence F5 NN, where NN is the substream
+number plus 1. Roland modules use this command to switch between different
+"parts", so this feature lets you treat each part as a distinct raw MIDI
+substream. The driver provides no way to send F5 00 (no selection) or to not
+send the F5 NN command sequence at all; perhaps it ought to.
+
+Usage example for simple serial converter:
+
+ /sbin/setserial /dev/ttyS0 uart none
+ /sbin/modprobe snd-serial-u16550 port=0x3f8 irq=4 speed=115200
+
+Usage example for Roland SoundCanvas with 4 MIDI ports:
+
+ /sbin/setserial /dev/ttyS0 uart none
+ /sbin/modprobe snd-serial-u16550 port=0x3f8 irq=4 outs=4
+
+In MS-124T mode, one raw MIDI substream is supported (midiCnD0); the outs
+module parameter is automatically set to 1. The driver sends the same data to
+all four MIDI Out connectors. Set the A-B switch and the speed module
+parameter to match (A=19200, B=9600).
+
+Usage example for MS-124T, with A-B switch in A position:
+
+ /sbin/setserial /dev/ttyS0 uart none
+ /sbin/modprobe snd-serial-u16550 port=0x3f8 irq=4 adaptor=1 \
+ speed=19200
+
+In MS-124W S/A mode, one raw MIDI substream is supported (midiCnD0);
+the outs module parameter is automatically set to 1. The driver sends
+the same data to all four MIDI Out connectors at full MIDI speed.
+
+Usage example for S/A mode:
+
+ /sbin/setserial /dev/ttyS0 uart none
+ /sbin/modprobe snd-serial-u16550 port=0x3f8 irq=4 adaptor=2
+
+In MS-124W M/B mode, the driver supports 16 ALSA raw MIDI substreams;
+the outs module parameter is automatically set to 16. The substream
+number gives a bitmask of which MIDI Out connectors the data should be
+sent to, with midiCnD1 sending to Out 1, midiCnD2 to Out 2, midiCnD4 to
+Out 3, and midiCnD8 to Out 4. Thus midiCnD15 sends the data to all 4 ports.
+As a special case, midiCnD0 also sends to all ports, since it is not useful
+to send the data to no ports. M/B mode has extra overhead to select the MIDI
+Out for each byte, so the aggregate data rate across all four MIDI Outs is
+at most one byte every 520 us, as compared with the full MIDI data rate of
+one byte every 320 us per port.
+
+Usage example for M/B mode:
+
+ /sbin/setserial /dev/ttyS0 uart none
+ /sbin/modprobe snd-serial-u16550 port=0x3f8 irq=4 adaptor=3
+
+The MS-124W hardware's M/A mode is currently not supported. This mode allows
+the MIDI Outs to act independently at double the aggregate throughput of M/B,
+but does not allow sending the same byte simultaneously to multiple MIDI Outs.
+The M/A protocol requires the driver to twiddle the modem control lines under
+timing constraints, so it would be a bit more complicated to implement than
+the other modes.
+
+Midiator models other than MS-124W and MS-124T are currently not supported.
+Note that the suffix letter is significant; the MS-124 and MS-124B are not
+compatible, nor are the other known models MS-101, MS-101B, MS-103, and MS-114.
+I do have documentation (tim.mann@compaq.com) that partially covers these models,
+but no units to experiment with. The MS-124W support is tested with a real unit.
+The MS-124T support is untested, but should work.
+
+The Generic driver supports multiple input and output substreams over a single
+serial port. Similar to Roland Soundcanvas mode, F5 NN is used to select the
+appropriate input or output stream (depending on the data direction).
+Additionally, the CTS signal is used to regulate the data flow. The number of
+inputs is specified by the ins parameter.