Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c
new file mode 100644
index 0000000..bedf88f
--- /dev/null
+++ b/arch/arm/mach-sa1100/assabet.c
@@ -0,0 +1,441 @@
+/*
+ * linux/arch/arm/mach-sa1100/assabet.c
+ *
+ * Author: Nicolas Pitre
+ *
+ * This file contains all Assabet-specific tweaks.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/serial_core.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/delay.h>
+#include <linux/mm.h>
+
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+#include <asm/setup.h>
+#include <asm/page.h>
+#include <asm/pgtable.h>
+#include <asm/tlbflush.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+#include <asm/mach/irda.h>
+#include <asm/mach/map.h>
+#include <asm/mach/serial_sa1100.h>
+#include <asm/arch/assabet.h>
+
+#include "generic.h"
+
+#define ASSABET_BCR_DB1110 \
+ (ASSABET_BCR_SPK_OFF | ASSABET_BCR_QMUTE | \
+ ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \
+ ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \
+ ASSABET_BCR_IRDA_MD0)
+
+#define ASSABET_BCR_DB1111 \
+ (ASSABET_BCR_SPK_OFF | ASSABET_BCR_QMUTE | \
+ ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \
+ ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \
+ ASSABET_BCR_CF_BUS_OFF | ASSABET_BCR_STEREO_LB | \
+ ASSABET_BCR_IRDA_MD0 | ASSABET_BCR_CF_RST)
+
+unsigned long SCR_value = ASSABET_SCR_INIT;
+EXPORT_SYMBOL(SCR_value);
+
+static unsigned long BCR_value = ASSABET_BCR_DB1110;
+
+void ASSABET_BCR_frob(unsigned int mask, unsigned int val)
+{
+ unsigned long flags;
+
+ local_irq_save(flags);
+ BCR_value = (BCR_value & ~mask) | val;
+ ASSABET_BCR = BCR_value;
+ local_irq_restore(flags);
+}
+
+EXPORT_SYMBOL(ASSABET_BCR_frob);
+
+static void assabet_backlight_power(int on)
+{
+#ifndef ASSABET_PAL_VIDEO
+ if (on)
+ ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON);
+ else
+#endif
+ ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
+}
+
+/*
+ * Turn on/off the backlight. When turning the backlight on,
+ * we wait 500us after turning it on so we don't cause the
+ * supplies to droop when we enable the LCD controller (and
+ * cause a hard reset.)
+ */
+static void assabet_lcd_power(int on)
+{
+#ifndef ASSABET_PAL_VIDEO
+ if (on) {
+ ASSABET_BCR_set(ASSABET_BCR_LCD_ON);
+ udelay(500);
+ } else
+#endif
+ ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
+}
+
+
+/*
+ * Assabet flash support code.
+ */
+
+#ifdef ASSABET_REV_4
+/*
+ * Phase 4 Assabet has two 28F160B3 flash parts in bank 0:
+ */
+static struct mtd_partition assabet_partitions[] = {
+ {
+ .name = "bootloader",
+ .size = 0x00020000,
+ .offset = 0,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "bootloader params",
+ .size = 0x00020000,
+ .offset = MTDPART_OFS_APPEND,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "jffs",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+#else
+/*
+ * Phase 5 Assabet has two 28F128J3A flash parts in bank 0:
+ */
+static struct mtd_partition assabet_partitions[] = {
+ {
+ .name = "bootloader",
+ .size = 0x00040000,
+ .offset = 0,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "bootloader params",
+ .size = 0x00040000,
+ .offset = MTDPART_OFS_APPEND,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "jffs",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+#endif
+
+static struct flash_platform_data assabet_flash_data = {
+ .map_name = "cfi_probe",
+ .parts = assabet_partitions,
+ .nr_parts = ARRAY_SIZE(assabet_partitions),
+};
+
+static struct resource assabet_flash_resources[] = {
+ {
+ .start = SA1100_CS0_PHYS,
+ .end = SA1100_CS0_PHYS + SZ_32M - 1,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = SA1100_CS1_PHYS,
+ .end = SA1100_CS1_PHYS + SZ_32M - 1,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
+
+/*
+ * Assabet IrDA support code.
+ */
+
+static int assabet_irda_set_power(struct device *dev, unsigned int state)
+{
+ static unsigned int bcr_state[4] = {
+ ASSABET_BCR_IRDA_MD0,
+ ASSABET_BCR_IRDA_MD1|ASSABET_BCR_IRDA_MD0,
+ ASSABET_BCR_IRDA_MD1,
+ 0
+ };
+
+ if (state < 4) {
+ state = bcr_state[state];
+ ASSABET_BCR_clear(state ^ (ASSABET_BCR_IRDA_MD1|
+ ASSABET_BCR_IRDA_MD0));
+ ASSABET_BCR_set(state);
+ }
+ return 0;
+}
+
+static void assabet_irda_set_speed(struct device *dev, unsigned int speed)
+{
+ if (speed < 4000000)
+ ASSABET_BCR_clear(ASSABET_BCR_IRDA_FSEL);
+ else
+ ASSABET_BCR_set(ASSABET_BCR_IRDA_FSEL);
+}
+
+static struct irda_platform_data assabet_irda_data = {
+ .set_power = assabet_irda_set_power,
+ .set_speed = assabet_irda_set_speed,
+};
+
+static void __init assabet_init(void)
+{
+ /*
+ * Ensure that the power supply is in "high power" mode.
+ */
+ GPDR |= GPIO_GPIO16;
+ GPSR = GPIO_GPIO16;
+
+ /*
+ * Ensure that these pins are set as outputs and are driving
+ * logic 0. This ensures that we won't inadvertently toggle
+ * the WS latch in the CPLD, and we don't float causing
+ * excessive power drain. --rmk
+ */
+ GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
+ GPCR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
+
+ /*
+ * Set up registers for sleep mode.
+ */
+ PWER = PWER_GPIO0;
+ PGSR = 0;
+ PCFR = 0;
+ PSDR = 0;
+ PPDR |= PPC_TXD3 | PPC_TXD1;
+ PPSR |= PPC_TXD3 | PPC_TXD1;
+
+ sa1100fb_lcd_power = assabet_lcd_power;
+ sa1100fb_backlight_power = assabet_backlight_power;
+
+ if (machine_has_neponset()) {
+ /*
+ * Angel sets this, but other bootloaders may not.
+ *
+ * This must precede any driver calls to BCR_set()
+ * or BCR_clear().
+ */
+ ASSABET_BCR = BCR_value = ASSABET_BCR_DB1111;
+
+#ifndef CONFIG_ASSABET_NEPONSET
+ printk( "Warning: Neponset detected but full support "
+ "hasn't been configured in the kernel\n" );
+#endif
+ }
+
+ sa11x0_set_flash_data(&assabet_flash_data, assabet_flash_resources,
+ ARRAY_SIZE(assabet_flash_resources));
+ sa11x0_set_irda_data(&assabet_irda_data);
+}
+
+/*
+ * On Assabet, we must probe for the Neponset board _before_
+ * paging_init() has occurred to actually determine the amount
+ * of RAM available. To do so, we map the appropriate IO section
+ * in the page table here in order to access GPIO registers.
+ */
+static void __init map_sa1100_gpio_regs( void )
+{
+ unsigned long phys = __PREG(GPLR) & PMD_MASK;
+ unsigned long virt = io_p2v(phys);
+ int prot = PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_DOMAIN(DOMAIN_IO);
+ pmd_t *pmd;
+
+ pmd = pmd_offset(pgd_offset_k(virt), virt);
+ *pmd = __pmd(phys | prot);
+ flush_pmd_entry(pmd);
+}
+
+/*
+ * Read System Configuration "Register"
+ * (taken from "Intel StrongARM SA-1110 Microprocessor Development Board
+ * User's Guide", section 4.4.1)
+ *
+ * This same scan is performed in arch/arm/boot/compressed/head-sa1100.S
+ * to set up the serial port for decompression status messages. We
+ * repeat it here because the kernel may not be loaded as a zImage, and
+ * also because it's a hassle to communicate the SCR value to the kernel
+ * from the decompressor.
+ *
+ * Note that IRQs are guaranteed to be disabled.
+ */
+static void __init get_assabet_scr(void)
+{
+ unsigned long scr, i;
+
+ GPDR |= 0x3fc; /* Configure GPIO 9:2 as outputs */
+ GPSR = 0x3fc; /* Write 0xFF to GPIO 9:2 */
+ GPDR &= ~(0x3fc); /* Configure GPIO 9:2 as inputs */
+ for(i = 100; i--; scr = GPLR); /* Read GPIO 9:2 */
+ GPDR |= 0x3fc; /* restore correct pin direction */
+ scr &= 0x3fc; /* save as system configuration byte. */
+ SCR_value = scr;
+}
+
+static void __init
+fixup_assabet(struct machine_desc *desc, struct tag *tags,
+ char **cmdline, struct meminfo *mi)
+{
+ /* This must be done before any call to machine_has_neponset() */
+ map_sa1100_gpio_regs();
+ get_assabet_scr();
+
+ if (machine_has_neponset())
+ printk("Neponset expansion board detected\n");
+}
+
+
+static void assabet_uart_pm(struct uart_port *port, u_int state, u_int oldstate)
+{
+ if (port->mapbase == _Ser1UTCR0) {
+ if (state)
+ ASSABET_BCR_clear(ASSABET_BCR_RS232EN |
+ ASSABET_BCR_COM_RTS |
+ ASSABET_BCR_COM_DTR);
+ else
+ ASSABET_BCR_set(ASSABET_BCR_RS232EN |
+ ASSABET_BCR_COM_RTS |
+ ASSABET_BCR_COM_DTR);
+ }
+}
+
+/*
+ * Assabet uses COM_RTS and COM_DTR for both UART1 (com port)
+ * and UART3 (radio module). We only handle them for UART1 here.
+ */
+static void assabet_set_mctrl(struct uart_port *port, u_int mctrl)
+{
+ if (port->mapbase == _Ser1UTCR0) {
+ u_int set = 0, clear = 0;
+
+ if (mctrl & TIOCM_RTS)
+ clear |= ASSABET_BCR_COM_RTS;
+ else
+ set |= ASSABET_BCR_COM_RTS;
+
+ if (mctrl & TIOCM_DTR)
+ clear |= ASSABET_BCR_COM_DTR;
+ else
+ set |= ASSABET_BCR_COM_DTR;
+
+ ASSABET_BCR_clear(clear);
+ ASSABET_BCR_set(set);
+ }
+}
+
+static u_int assabet_get_mctrl(struct uart_port *port)
+{
+ u_int ret = 0;
+ u_int bsr = ASSABET_BSR;
+
+ /* need 2 reads to read current value */
+ bsr = ASSABET_BSR;
+
+ if (port->mapbase == _Ser1UTCR0) {
+ if (bsr & ASSABET_BSR_COM_DCD)
+ ret |= TIOCM_CD;
+ if (bsr & ASSABET_BSR_COM_CTS)
+ ret |= TIOCM_CTS;
+ if (bsr & ASSABET_BSR_COM_DSR)
+ ret |= TIOCM_DSR;
+ } else if (port->mapbase == _Ser3UTCR0) {
+ if (bsr & ASSABET_BSR_RAD_DCD)
+ ret |= TIOCM_CD;
+ if (bsr & ASSABET_BSR_RAD_CTS)
+ ret |= TIOCM_CTS;
+ if (bsr & ASSABET_BSR_RAD_DSR)
+ ret |= TIOCM_DSR;
+ if (bsr & ASSABET_BSR_RAD_RI)
+ ret |= TIOCM_RI;
+ } else {
+ ret = TIOCM_CD | TIOCM_CTS | TIOCM_DSR;
+ }
+
+ return ret;
+}
+
+static struct sa1100_port_fns assabet_port_fns __initdata = {
+ .set_mctrl = assabet_set_mctrl,
+ .get_mctrl = assabet_get_mctrl,
+ .pm = assabet_uart_pm,
+};
+
+static struct map_desc assabet_io_desc[] __initdata = {
+ /* virtual physical length type */
+ { 0xf1000000, 0x12000000, 0x00100000, MT_DEVICE }, /* Board Control Register */
+ { 0xf2800000, 0x4b800000, 0x00800000, MT_DEVICE } /* MQ200 */
+};
+
+static void __init assabet_map_io(void)
+{
+ sa1100_map_io();
+ iotable_init(assabet_io_desc, ARRAY_SIZE(assabet_io_desc));
+
+ /*
+ * Set SUS bit in SDCR0 so serial port 1 functions.
+ * Its called GPCLKR0 in my SA1110 manual.
+ */
+ Ser1SDCR0 |= SDCR0_SUS;
+
+ if (machine_has_neponset()) {
+#ifdef CONFIG_ASSABET_NEPONSET
+ extern void neponset_map_io(void);
+
+ /*
+ * We map Neponset registers even if it isn't present since
+ * many drivers will try to probe their stuff (and fail).
+ * This is still more friendly than a kernel paging request
+ * crash.
+ */
+ neponset_map_io();
+#endif
+ } else {
+ sa1100_register_uart_fns(&assabet_port_fns);
+ }
+
+ /*
+ * When Neponset is attached, the first UART should be
+ * UART3. That's what Angel is doing and many documents
+ * are stating this.
+ *
+ * We do the Neponset mapping even if Neponset support
+ * isn't compiled in so the user will still get something on
+ * the expected physical serial port.
+ *
+ * We no longer do this; not all boot loaders support it,
+ * and UART3 appears to be somewhat unreliable with blob.
+ */
+ sa1100_register_uart(0, 1);
+ sa1100_register_uart(2, 3);
+}
+
+
+MACHINE_START(ASSABET, "Intel-Assabet")
+ BOOT_MEM(0xc0000000, 0x80000000, 0xf8000000)
+ BOOT_PARAMS(0xc0000100)
+ FIXUP(fixup_assabet)
+ MAPIO(assabet_map_io)
+ INITIRQ(sa1100_init_irq)
+ .timer = &sa1100_timer,
+ .init_machine = assabet_init,
+MACHINE_END