diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
new file mode 100644
index 0000000..8d113d6
--- /dev/null
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -0,0 +1,224 @@
+/*
+ * linux/arch/arm/mach-sa1100/simpad.c
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/tty.h>
+#include <linux/proc_fs.h>
+#include <linux/string.h> 
+#include <linux/pm.h>
+#include <linux/device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/irq.h>
+#include <asm/hardware.h>
+#include <asm/setup.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+#include <asm/mach/map.h>
+#include <asm/mach/serial_sa1100.h>
+#include <asm/arch/simpad.h>
+
+#include <linux/serial_core.h>
+#include <linux/ioport.h>
+#include <asm/io.h>
+
+#include "generic.h"
+
+long cs3_shadow;
+
+long get_cs3_shadow(void)
+{
+	return cs3_shadow;
+}
+
+void set_cs3(long value)
+{
+	*(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow = value;
+}
+
+void set_cs3_bit(int value)
+{
+	cs3_shadow |= value;
+	*(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow;
+}
+
+void clear_cs3_bit(int value)
+{
+	cs3_shadow &= ~value;
+	*(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow;
+}
+
+EXPORT_SYMBOL(set_cs3_bit);
+EXPORT_SYMBOL(clear_cs3_bit);
+
+static struct map_desc simpad_io_desc[] __initdata = {
+        /* virtual	physical    length	type */
+	/* MQ200 */
+	{ 0xf2800000, 0x4b800000, 0x00800000, MT_DEVICE },
+	/* Paules CS3, write only */
+	{ 0xf1000000, 0x18000000, 0x00100000, MT_DEVICE },
+};
+
+
+static void simpad_uart_pm(struct uart_port *port, u_int state, u_int oldstate)
+{
+	if (port->mapbase == (u_int)&Ser1UTCR0) {
+		if (state)
+		{
+			clear_cs3_bit(RS232_ON);
+			clear_cs3_bit(DECT_POWER_ON);
+		}else
+		{
+			set_cs3_bit(RS232_ON);
+			set_cs3_bit(DECT_POWER_ON);
+		}
+	}
+}
+
+static struct sa1100_port_fns simpad_port_fns __initdata = {
+	.pm	   = simpad_uart_pm,
+};
+
+
+static struct mtd_partition simpad_partitions[] = {
+	{
+		.name       = "SIMpad boot firmware",
+		.size       = 0x00080000,
+		.offset     = 0,
+		.mask_flags = MTD_WRITEABLE,
+	}, {
+		.name       = "SIMpad kernel",
+		.size       = 0x0010000,
+		.offset     = MTDPART_OFS_APPEND,
+	}, {
+		.name       = "SIMpad root jffs2",
+		.size       = MTDPART_SIZ_FULL,
+		.offset     = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct flash_platform_data simpad_flash_data = {
+	.map_name    = "cfi_probe",
+	.parts       = simpad_partitions,
+	.nr_parts    = ARRAY_SIZE(simpad_partitions),
+};
+
+
+static struct resource simpad_flash_resources [] = {
+	{
+		.start     = SA1100_CS0_PHYS,
+		.end       = SA1100_CS0_PHYS + SZ_16M -1,
+		.flags     = IORESOURCE_MEM,
+	}, {
+		.start     = SA1100_CS1_PHYS,
+		.end       = SA1100_CS1_PHYS + SZ_16M -1,
+		.flags     = IORESOURCE_MEM,
+	}
+};
+
+
+
+static void __init simpad_map_io(void)
+{
+	sa1100_map_io();
+
+	iotable_init(simpad_io_desc, ARRAY_SIZE(simpad_io_desc));
+
+	set_cs3_bit (EN1 | EN0 | LED2_ON | DISPLAY_ON | RS232_ON |
+		      ENABLE_5V | RESET_SIMCARD | DECT_POWER_ON);
+
+
+        sa1100_register_uart_fns(&simpad_port_fns);
+	sa1100_register_uart(0, 3);  /* serial interface */
+	sa1100_register_uart(1, 1);  /* DECT             */
+
+	// Reassign UART 1 pins
+	GAFR |= GPIO_UART_TXD | GPIO_UART_RXD;
+	GPDR |= GPIO_UART_TXD | GPIO_LDD13 | GPIO_LDD15;
+	GPDR &= ~GPIO_UART_RXD;
+	PPAR |= PPAR_UPR;
+
+	/*
+	 * Set up registers for sleep mode.
+	 */
+
+
+	PWER = PWER_GPIO0| PWER_RTC;
+	PGSR = 0x818;
+	PCFR = 0;
+	PSDR = 0;
+
+	sa11x0_set_flash_data(&simpad_flash_data, simpad_flash_resources,
+			      ARRAY_SIZE(simpad_flash_resources));
+}
+
+static void simpad_power_off(void)
+{
+	local_irq_disable(); // was cli
+	set_cs3(0x800);        /* only SD_MEDIAQ */
+
+	/* disable internal oscillator, float CS lines */
+	PCFR = (PCFR_OPDE | PCFR_FP | PCFR_FS);
+	/* enable wake-up on GPIO0 (Assabet...) */
+	PWER = GFER = GRER = 1;
+	/*
+	 * set scratchpad to zero, just in case it is used as a
+	 * restart address by the bootloader.
+	 */
+	PSPR = 0;
+	PGSR = 0;
+	/* enter sleep mode */
+	PMCR = PMCR_SF;
+	while(1);
+
+	local_irq_enable(); /* we won't ever call it */
+
+
+}
+
+
+/*
+ * MediaQ Video Device
+ */
+static struct platform_device simpad_mq200fb = {
+	.name = "simpad-mq200",
+	.id   = 0,
+};
+
+static struct platform_device *devices[] __initdata = {
+	&simpad_mq200fb
+};
+
+
+
+static int __init simpad_init(void)
+{
+	int ret;
+
+	pm_power_off = simpad_power_off;
+
+	ret = platform_add_devices(devices, ARRAY_SIZE(devices));
+	if(ret)
+		printk(KERN_WARNING "simpad: Unable to register mq200 framebuffer device");
+
+	return 0;
+}
+
+arch_initcall(simpad_init);
+
+
+MACHINE_START(SIMPAD, "Simpad")
+	MAINTAINER("Holger Freyther")
+	BOOT_MEM(0xc0000000, 0x80000000, 0xf8000000)
+        BOOT_PARAMS(0xc0000100)
+	MAPIO(simpad_map_io)
+	INITIRQ(sa1100_init_irq)
+	.timer		= &sa1100_timer,
+MACHINE_END