Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/arch/h8300/Kconfig b/arch/h8300/Kconfig
new file mode 100644
index 0000000..62a89e8
--- /dev/null
+++ b/arch/h8300/Kconfig
@@ -0,0 +1,194 @@
+#
+# For a description of the syntax of this configuration file,
+# see Documentation/kbuild/config-language.txt.
+#
+
+mainmenu "uClinux/h8300 (w/o MMU) Kernel Configuration"
+
+config H8300
+ bool
+ default y
+
+config MMU
+ bool
+ default n
+
+config SWAP
+ bool
+ default n
+
+config FPU
+ bool
+ default n
+
+config UID16
+ bool
+ default y
+
+config RWSEM_GENERIC_SPINLOCK
+ bool
+ default y
+
+config RWSEM_XCHGADD_ALGORITHM
+ bool
+ default n
+
+config GENERIC_CALIBRATE_DELAY
+ bool
+ default y
+
+config ISA
+ bool
+ default y
+
+config PCI
+ bool
+ default n
+
+source "init/Kconfig"
+
+source "arch/h8300/Kconfig.cpu"
+
+menu "Executable file formats"
+
+source "fs/Kconfig.binfmt"
+
+endmenu
+
+source "drivers/base/Kconfig"
+
+source "drivers/mtd/Kconfig"
+
+source "drivers/block/Kconfig"
+
+source "drivers/ide/Kconfig"
+
+source "arch/h8300/Kconfig.ide"
+
+source "net/Kconfig"
+
+#
+# input - input/joystick depends on it. As does USB.
+#
+source "drivers/input/Kconfig"
+
+menu "Character devices"
+
+config VT
+ bool "Virtual terminal"
+ ---help---
+ If you say Y here, you will get support for terminal devices with
+ display and keyboard devices. These are called "virtual" because you
+ can run several virtual terminals (also called virtual consoles) on
+ one physical terminal. This is rather useful, for example one
+ virtual terminal can collect system messages and warnings, another
+ one can be used for a text-mode user session, and a third could run
+ an X session, all in parallel. Switching between virtual terminals
+ is done with certain key combinations, usually Alt-<function key>.
+
+ The setterm command ("man setterm") can be used to change the
+ properties (such as colors or beeping) of a virtual terminal. The
+ man page console_codes(4) ("man console_codes") contains the special
+ character sequences that can be used to change those properties
+ directly. The fonts used on virtual terminals can be changed with
+ the setfont ("man setfont") command and the key bindings are defined
+ with the loadkeys ("man loadkeys") command.
+
+ You need at least one virtual terminal device in order to make use
+ of your keyboard and monitor. Therefore, only people configuring an
+ embedded system would want to say N here in order to save some
+ memory; the only way to log into such a system is then via a serial
+ or network connection.
+
+ If unsure, say Y, or else you won't be able to do much with your new
+ shiny Linux system :-)
+
+config VT_CONSOLE
+ bool "Support for console on virtual terminal"
+ depends on VT
+ ---help---
+ The system console is the device which receives all kernel messages
+ and warnings and which allows logins in single user mode. If you
+ answer Y here, a virtual terminal (the device used to interact with
+ a physical terminal) can be used as system console. This is the most
+ common mode of operations, so you should say Y here unless you want
+ the kernel messages be output only to a serial port (in which case
+ you should say Y to "Console on serial port", below).
+
+ If you do say Y here, by default the currently visible virtual
+ terminal (/dev/tty0) will be used as system console. You can change
+ that with a kernel command line option such as "console=tty3" which
+ would use the third virtual terminal as system console. (Try "man
+ bootparam" or see the documentation of your boot loader (lilo or
+ loadlin) about how to pass options to the kernel at boot time.)
+
+ If unsure, say Y.
+
+config HW_CONSOLE
+ bool
+ depends on VT && !S390 && !UM
+ default y
+
+comment "Unix98 PTY support"
+
+config UNIX98_PTYS
+ bool "Unix98 PTY support"
+ ---help---
+ A pseudo terminal (PTY) is a software device consisting of two
+ halves: a master and a slave. The slave device behaves identical to
+ a physical terminal; the master device is used by a process to
+ read data from and write data to the slave, thereby emulating a
+ terminal. Typical programs for the master side are telnet servers
+ and xterms.
+
+ Linux has traditionally used the BSD-like names /dev/ptyxx for
+ masters and /dev/ttyxx for slaves of pseudo terminals. This scheme
+ has a number of problems. The GNU C library glibc 2.1 and later,
+ however, supports the Unix98 naming standard: in order to acquire a
+ pseudo terminal, a process opens /dev/ptmx; the number of the pseudo
+ terminal is then made available to the process and the pseudo
+ terminal slave can be accessed as /dev/pts/<number>. What was
+ traditionally /dev/ttyp2 will then be /dev/pts/2, for example.
+
+ The entries in /dev/pts/ are created on the fly by a virtual
+ file system; therefore, if you say Y here you should say Y to
+ "/dev/pts file system for Unix98 PTYs" as well.
+
+ If you want to say Y here, you need to have the C library glibc 2.1
+ or later (equal to libc-6.1, check with "ls -l /lib/libc.so.*").
+ Read the instructions in <file:Documentation/Changes> pertaining to
+ pseudo terminals. It's safe to say N.
+
+config UNIX98_PTY_COUNT
+ int "Maximum number of Unix98 PTYs in use (0-2048)"
+ depends on UNIX98_PTYS
+ default "256"
+ help
+ The maximum number of Unix98 PTYs that can be used at any one time.
+ The default is 256, and should be enough for desktop systems. Server
+ machines which support incoming telnet/rlogin/ssh connections and/or
+ serve several X terminals may want to increase this: every incoming
+ connection and every xterm uses up one PTY.
+
+ When not in use, each additional set of 256 PTYs occupy
+ approximately 8 KB of kernel memory on 32-bit architectures.
+
+source "drivers/char/pcmcia/Kconfig"
+
+source "drivers/serial/Kconfig"
+
+source "drivers/i2c/Kconfig"
+
+source "drivers/usb/Kconfig"
+
+endmenu
+
+source "fs/Kconfig"
+
+source "arch/h8300/Kconfig.debug"
+
+source "security/Kconfig"
+
+source "crypto/Kconfig"
+
+source "lib/Kconfig"