Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/arch/i386/mach-visws/setup.c b/arch/i386/mach-visws/setup.c
new file mode 100644
index 0000000..9f6d2d9
--- /dev/null
+++ b/arch/i386/mach-visws/setup.c
@@ -0,0 +1,134 @@
+/*
+ * Unmaintained SGI Visual Workstation support.
+ * Split out from setup.c by davej@suse.de
+ */
+
+#include <linux/smp.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+
+#include <asm/fixmap.h>
+#include <asm/arch_hooks.h>
+#include <asm/io.h>
+#include "cobalt.h"
+#include "piix4.h"
+
+char visws_board_type = -1;
+char visws_board_rev = -1;
+
+void __init visws_get_board_type_and_rev(void)
+{
+ int raw;
+
+ visws_board_type = (char)(inb_p(PIIX_GPI_BD_REG) & PIIX_GPI_BD_REG)
+ >> PIIX_GPI_BD_SHIFT;
+ /*
+ * Get Board rev.
+ * First, we have to initialize the 307 part to allow us access
+ * to the GPIO registers. Let's map them at 0x0fc0 which is right
+ * after the PIIX4 PM section.
+ */
+ outb_p(SIO_DEV_SEL, SIO_INDEX);
+ outb_p(SIO_GP_DEV, SIO_DATA); /* Talk to GPIO regs. */
+
+ outb_p(SIO_DEV_MSB, SIO_INDEX);
+ outb_p(SIO_GP_MSB, SIO_DATA); /* MSB of GPIO base address */
+
+ outb_p(SIO_DEV_LSB, SIO_INDEX);
+ outb_p(SIO_GP_LSB, SIO_DATA); /* LSB of GPIO base address */
+
+ outb_p(SIO_DEV_ENB, SIO_INDEX);
+ outb_p(1, SIO_DATA); /* Enable GPIO registers. */
+
+ /*
+ * Now, we have to map the power management section to write
+ * a bit which enables access to the GPIO registers.
+ * What lunatic came up with this shit?
+ */
+ outb_p(SIO_DEV_SEL, SIO_INDEX);
+ outb_p(SIO_PM_DEV, SIO_DATA); /* Talk to GPIO regs. */
+
+ outb_p(SIO_DEV_MSB, SIO_INDEX);
+ outb_p(SIO_PM_MSB, SIO_DATA); /* MSB of PM base address */
+
+ outb_p(SIO_DEV_LSB, SIO_INDEX);
+ outb_p(SIO_PM_LSB, SIO_DATA); /* LSB of PM base address */
+
+ outb_p(SIO_DEV_ENB, SIO_INDEX);
+ outb_p(1, SIO_DATA); /* Enable PM registers. */
+
+ /*
+ * Now, write the PM register which enables the GPIO registers.
+ */
+ outb_p(SIO_PM_FER2, SIO_PM_INDEX);
+ outb_p(SIO_PM_GP_EN, SIO_PM_DATA);
+
+ /*
+ * Now, initialize the GPIO registers.
+ * We want them all to be inputs which is the
+ * power on default, so let's leave them alone.
+ * So, let's just read the board rev!
+ */
+ raw = inb_p(SIO_GP_DATA1);
+ raw &= 0x7f; /* 7 bits of valid board revision ID. */
+
+ if (visws_board_type == VISWS_320) {
+ if (raw < 0x6) {
+ visws_board_rev = 4;
+ } else if (raw < 0xc) {
+ visws_board_rev = 5;
+ } else {
+ visws_board_rev = 6;
+ }
+ } else if (visws_board_type == VISWS_540) {
+ visws_board_rev = 2;
+ } else {
+ visws_board_rev = raw;
+ }
+
+ printk(KERN_INFO "Silicon Graphics Visual Workstation %s (rev %d) detected\n",
+ (visws_board_type == VISWS_320 ? "320" :
+ (visws_board_type == VISWS_540 ? "540" :
+ "unknown")), visws_board_rev);
+}
+
+void __init pre_intr_init_hook(void)
+{
+ init_VISWS_APIC_irqs();
+}
+
+void __init intr_init_hook(void)
+{
+#ifdef CONFIG_X86_LOCAL_APIC
+ apic_intr_init();
+#endif
+}
+
+void __init pre_setup_arch_hook()
+{
+ visws_get_board_type_and_rev();
+}
+
+static struct irqaction irq0 = {
+ .handler = timer_interrupt,
+ .flags = SA_INTERRUPT,
+ .name = "timer",
+};
+
+void __init time_init_hook(void)
+{
+ printk(KERN_INFO "Starting Cobalt Timer system clock\n");
+
+ /* Set the countdown value */
+ co_cpu_write(CO_CPU_TIMEVAL, CO_TIME_HZ/HZ);
+
+ /* Start the timer */
+ co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) | CO_CTRL_TIMERUN);
+
+ /* Enable (unmask) the timer interrupt */
+ co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) & ~CO_CTRL_TIMEMASK);
+
+ /* Wire cpu IDT entry to s/w handler (and Cobalt APIC to IDT) */
+ setup_irq(0, &irq0);
+}