Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/arch/m68k/Kconfig b/arch/m68k/Kconfig
new file mode 100644
index 0000000..d0713c7d
--- /dev/null
+++ b/arch/m68k/Kconfig
@@ -0,0 +1,670 @@
+#
+# For a description of the syntax of this configuration file,
+# see Documentation/kbuild/kconfig-language.txt.
+#
+config M68K
+ bool
+ default y
+
+config MMU
+ bool
+ default y
+
+config UID16
+ bool
+ default y
+
+config RWSEM_GENERIC_SPINLOCK
+ bool
+ default y
+
+config RWSEM_XCHGADD_ALGORITHM
+ bool
+
+config GENERIC_CALIBRATE_DELAY
+ bool
+ default y
+
+mainmenu "Linux/68k Kernel Configuration"
+
+source "init/Kconfig"
+
+menu "Platform dependent setup"
+
+config EISA
+ bool
+ ---help---
+ The Extended Industry Standard Architecture (EISA) bus was
+ developed as an open alternative to the IBM MicroChannel bus.
+
+ The EISA bus provided some of the features of the IBM MicroChannel
+ bus while maintaining backward compatibility with cards made for
+ the older ISA bus. The EISA bus saw limited use between 1988 and
+ 1995 when it was made obsolete by the PCI bus.
+
+ Say Y here if you are building a kernel for an EISA-based machine.
+
+ Otherwise, say N.
+
+config MCA
+ bool
+ help
+ MicroChannel Architecture is found in some IBM PS/2 machines and
+ laptops. It is a bus system similar to PCI or ISA. See
+ <file:Documentation/mca.txt> (and especially the web page given
+ there) before attempting to build an MCA bus kernel.
+
+config PCMCIA
+ tristate
+ ---help---
+ Say Y here if you want to attach PCMCIA- or PC-cards to your Linux
+ computer. These are credit-card size devices such as network cards,
+ modems or hard drives often used with laptops computers. There are
+ actually two varieties of these cards: the older 16 bit PCMCIA cards
+ and the newer 32 bit CardBus cards. If you want to use CardBus
+ cards, you need to say Y here and also to "CardBus support" below.
+
+ To use your PC-cards, you will need supporting software from David
+ Hinds' pcmcia-cs package (see the file <file:Documentation/Changes>
+ for location). Please also read the PCMCIA-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as modules, choose M here: the
+ modules will be called pcmcia_core and ds.
+
+config SUN3
+ bool "Sun3 support"
+ select M68020
+ select MMU_SUN3 if MMU
+ help
+ This option enables support for the Sun 3 series of workstations
+ (3/50, 3/60, 3/1xx, 3/2xx systems). Enabling this option requires
+ that all other hardware types must be disabled, as Sun 3 kernels
+ are incompatible with all other m68k targets (including Sun 3x!).
+
+ If you don't want to compile a kernel exclusively for a Sun 3, say N.
+
+config AMIGA
+ bool "Amiga support"
+ depends on !MMU_SUN3
+ help
+ This option enables support for the Amiga series of computers. If
+ you plan to use this kernel on an Amiga, say Y here and browse the
+ material available in <file:Documentation/m68k>; otherwise say N.
+
+config ATARI
+ bool "Atari support"
+ depends on !MMU_SUN3
+ help
+ This option enables support for the 68000-based Atari series of
+ computers (including the TT, Falcon and Medusa). If you plan to use
+ this kernel on an Atari, say Y here and browse the material
+ available in <file:Documentation/m68k>; otherwise say N.
+
+config HADES
+ bool "Hades support"
+ depends on ATARI && BROKEN
+ help
+ This option enables support for the Hades Atari clone. If you plan
+ to use this kernel on a Hades, say Y here; otherwise say N.
+
+config PCI
+ bool
+ depends on HADES
+ default y
+ help
+ Find out whether you have a PCI motherboard. PCI is the name of a
+ bus system, i.e. the way the CPU talks to the other stuff inside
+ your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
+ VESA. If you have PCI, say Y, otherwise N.
+
+ The PCI-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>, contains valuable
+ information about which PCI hardware does work under Linux and which
+ doesn't.
+
+config MAC
+ bool "Macintosh support"
+ depends on !MMU_SUN3
+ help
+ This option enables support for the Apple Macintosh series of
+ computers (yes, there is experimental support now, at least for part
+ of the series).
+
+ Say N unless you're willing to code the remaining necessary support.
+ ;)
+
+config NUBUS
+ bool
+ depends on MAC
+ default y
+
+config M68K_L2_CACHE
+ bool
+ depends on MAC
+ default y
+
+config APOLLO
+ bool "Apollo support"
+ depends on !MMU_SUN3
+ help
+ Say Y here if you want to run Linux on an MC680x0-based Apollo
+ Domain workstation such as the DN3500.
+
+config VME
+ bool "VME (Motorola and BVM) support"
+ depends on !MMU_SUN3
+ help
+ Say Y here if you want to build a kernel for a 680x0 based VME
+ board. Boards currently supported include Motorola boards MVME147,
+ MVME162, MVME166, MVME167, MVME172, and MVME177. BVME4000 and
+ BVME6000 boards from BVM Ltd are also supported.
+
+config MVME147
+ bool "MVME147 support"
+ depends on VME
+ help
+ Say Y to include support for early Motorola VME boards. This will
+ build a kernel which can run on MVME147 single-board computers. If
+ you select this option you will have to select the appropriate
+ drivers for SCSI, Ethernet and serial ports later on.
+
+config MVME16x
+ bool "MVME162, 166 and 167 support"
+ depends on VME
+ help
+ Say Y to include support for Motorola VME boards. This will build a
+ kernel which can run on MVME162, MVME166, MVME167, MVME172, and
+ MVME177 boards. If you select this option you will have to select
+ the appropriate drivers for SCSI, Ethernet and serial ports later
+ on.
+
+config BVME6000
+ bool "BVME4000 and BVME6000 support"
+ depends on VME
+ help
+ Say Y to include support for VME boards from BVM Ltd. This will
+ build a kernel which can run on BVME4000 and BVME6000 boards. If
+ you select this option you will have to select the appropriate
+ drivers for SCSI, Ethernet and serial ports later on.
+
+config HP300
+ bool "HP9000/300 and HP9000/400 support"
+ depends on !MMU_SUN3
+ help
+ This option enables support for the HP9000/300 and HP9000/400 series
+ of workstations. Support for these machines is still somewhat
+ experimental. If you plan to try to use the kernel on such a machine
+ say Y here.
+ Everybody else says N.
+
+config DIO
+ bool "DIO bus support"
+ depends on HP300
+ default y
+ help
+ Say Y here to enable support for the "DIO" expansion bus used in
+ HP300 machines. If you are using such a system you almost certainly
+ want this.
+
+config SUN3X
+ bool "Sun3x support"
+ depends on !MMU_SUN3
+ select M68030
+ help
+ This option enables support for the Sun 3x series of workstations.
+ Be warned that this support is very experimental.
+ Note that Sun 3x kernels are not compatible with Sun 3 hardware.
+ General Linux information on the Sun 3x series (now discontinued)
+ is at <http://www.angelfire.com/ca2/tech68k/sun3.html>.
+
+ If you don't want to compile a kernel for a Sun 3x, say N.
+
+config Q40
+ bool "Q40/Q60 support"
+ depends on !MMU_SUN3
+ help
+ The Q40 is a Motorola 68040-based successor to the Sinclair QL
+ manufactured in Germany. There is an official Q40 home page at
+ <http://www.q40.de/>. This option enables support for the Q40 and
+ Q60. Select your CPU below. For 68LC060 don't forget to enable FPU
+ emulation.
+
+comment "Processor type"
+
+config M68020
+ bool "68020 support"
+ help
+ If you anticipate running this kernel on a computer with a MC68020
+ processor, say Y. Otherwise, say N. Note that the 68020 requires a
+ 68851 MMU (Memory Management Unit) to run Linux/m68k, except on the
+ Sun 3, which provides its own version.
+
+config M68030
+ bool "68030 support"
+ depends on !MMU_SUN3
+ help
+ If you anticipate running this kernel on a computer with a MC68030
+ processor, say Y. Otherwise, say N. Note that a MC68EC030 will not
+ work, as it does not include an MMU (Memory Management Unit).
+
+config M68040
+ bool "68040 support"
+ depends on !MMU_SUN3
+ help
+ If you anticipate running this kernel on a computer with a MC68LC040
+ or MC68040 processor, say Y. Otherwise, say N. Note that an
+ MC68EC040 will not work, as it does not include an MMU (Memory
+ Management Unit).
+
+config M68060
+ bool "68060 support"
+ depends on !MMU_SUN3
+ help
+ If you anticipate running this kernel on a computer with a MC68060
+ processor, say Y. Otherwise, say N.
+
+config MMU_MOTOROLA
+ bool
+ depends on MMU && !MMU_SUN3
+ default y
+
+config MMU_SUN3
+ bool
+
+config M68KFPU_EMU
+ bool "Math emulation support (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ help
+ At some point in the future, this will cause floating-point math
+ instructions to be emulated by the kernel on machines that lack a
+ floating-point math coprocessor. Thrill-seekers and chronically
+ sleep-deprived psychotic hacker types can say Y now, everyone else
+ should probably wait a while.
+
+config M68KFPU_EMU_EXTRAPREC
+ bool "Math emulation extra precision"
+ depends on M68KFPU_EMU
+ help
+ The fpu uses normally a few bit more during calculations for
+ correct rounding, the emulator can (often) do the same but this
+ extra calculation can cost quite some time, so you can disable
+ it here. The emulator will then "only" calculate with a 64 bit
+ mantissa and round slightly incorrect, what is more then enough
+ for normal usage.
+
+config M68KFPU_EMU_ONLY
+ bool "Math emulation only kernel"
+ depends on M68KFPU_EMU
+ help
+ This option prevents any floating-point instructions from being
+ compiled into the kernel, thereby the kernel doesn't save any
+ floating point context anymore during task switches, so this
+ kernel will only be usable on machines without a floating-point
+ math coprocessor. This makes the kernel a bit faster as no tests
+ needs to be executed whether a floating-point instruction in the
+ kernel should be executed or not.
+
+config ADVANCED
+ bool "Advanced configuration options"
+ ---help---
+ This gives you access to some advanced options for the CPU. The
+ defaults should be fine for most users, but these options may make
+ it possible for you to improve performance somewhat if you know what
+ you are doing.
+
+ Note that the answer to this question won't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about these options.
+
+ Most users should say N to this question.
+
+config RMW_INSNS
+ bool "Use read-modify-write instructions"
+ depends on ADVANCED
+ ---help---
+ This allows to use certain instructions that work with indivisible
+ read-modify-write bus cycles. While this is faster than the
+ workaround of disabling interrupts, it can conflict with DMA
+ ( = direct memory access) on many Amiga systems, and it is also said
+ to destabilize other machines. It is very likely that this will
+ cause serious problems on any Amiga or Atari Medusa if set. The only
+ configuration where it should work are 68030-based Ataris, where it
+ apparently improves performance. But you've been warned! Unless you
+ really know what you are doing, say N. Try Y only if you're quite
+ adventurous.
+
+config SINGLE_MEMORY_CHUNK
+ bool "Use one physical chunk of memory only"
+ depends on ADVANCED && !SUN3
+ help
+ Ignore all but the first contiguous chunk of physical memory for VM
+ purposes. This will save a few bytes kernel size and may speed up
+ some operations. Say N if not sure.
+
+config 060_WRITETHROUGH
+ bool "Use write-through caching for 68060 supervisor accesses"
+ depends on ADVANCED && M68060
+ ---help---
+ The 68060 generally uses copyback caching of recently accessed data.
+ Copyback caching means that memory writes will be held in an on-chip
+ cache and only written back to memory some time later. Saying Y
+ here will force supervisor (kernel) accesses to use writethrough
+ caching. Writethrough caching means that data is written to memory
+ straight away, so that cache and memory data always agree.
+ Writethrough caching is less efficient, but is needed for some
+ drivers on 68060 based systems where the 68060 bus snooping signal
+ is hardwired on. The 53c710 SCSI driver is known to suffer from
+ this problem.
+
+endmenu
+
+menu "General setup"
+
+source "fs/Kconfig.binfmt"
+
+config ZORRO
+ bool "Amiga Zorro (AutoConfig) bus support"
+ depends on AMIGA
+ help
+ This enables support for the Zorro bus in the Amiga. If you have
+ expansion cards in your Amiga that conform to the Amiga
+ AutoConfig(tm) specification, say Y, otherwise N. Note that even
+ expansion cards that do not fit in the Zorro slots but fit in e.g.
+ the CPU slot may fall in this category, so you have to say Y to let
+ Linux use these.
+
+config AMIGA_PCMCIA
+ bool "Amiga 1200/600 PCMCIA support (EXPERIMENTAL)"
+ depends on AMIGA && EXPERIMENTAL
+ help
+ Include support in the kernel for pcmcia on Amiga 1200 and Amiga
+ 600. If you intend to use pcmcia cards say Y; otherwise say N.
+
+config STRAM_SWAP
+ bool "Support for ST-RAM as swap space"
+ depends on ATARI && BROKEN
+ ---help---
+ Some Atari 68k machines (including the 520STF and 1020STE) divide
+ their addressable memory into ST and TT sections. The TT section
+ (up to 512MB) is the main memory; the ST section (up to 4MB) is
+ accessible to the built-in graphics board, runs slower, and is
+ present mainly for backward compatibility with older machines.
+
+ This enables support for using (parts of) ST-RAM as swap space,
+ instead of as normal system memory. This can first enhance system
+ performance if you have lots of alternate RAM (compared to the size
+ of ST-RAM), because executable code always will reside in faster
+ memory. ST-RAM will remain as ultra-fast swap space. On the other
+ hand, it allows much improved dynamic allocations of ST-RAM buffers
+ for device driver modules (e.g. floppy, ACSI, SLM printer, DMA
+ sound). The probability that such allocations at module load time
+ fail is drastically reduced.
+
+config STRAM_PROC
+ bool "ST-RAM statistics in /proc"
+ depends on ATARI
+ help
+ Say Y here to report ST-RAM usage statistics in /proc/stram. See
+ the help for CONFIG_STRAM_SWAP for discussion of ST-RAM and its
+ uses.
+
+config HEARTBEAT
+ bool "Use power LED as a heartbeat" if AMIGA || APOLLO || ATARI || MAC ||Q40
+ default y if !AMIGA && !APOLLO && !ATARI && !MAC && !Q40 && HP300
+ help
+ Use the power-on LED on your machine as a load meter. The exact
+ behavior is platform-dependent, but normally the flash frequency is
+ a hyperbolic function of the 5-minute load average.
+
+# We have a dedicated heartbeat LED. :-)
+config PROC_HARDWARE
+ bool "/proc/hardware support"
+ help
+ Say Y here to support the /proc/hardware file, which gives you
+ access to information about the machine you're running on,
+ including the model, CPU, MMU, clock speed, BogoMIPS rating,
+ and memory size.
+
+config ISA
+ bool
+ depends on Q40 || AMIGA_PCMCIA || GG2
+ default y
+ help
+ Find out whether you have ISA slots on your motherboard. ISA is the
+ name of a bus system, i.e. the way the CPU talks to the other stuff
+ inside your box. Other bus systems are PCI, EISA, MicroChannel
+ (MCA) or VESA. ISA is an older system, now being displaced by PCI;
+ newer boards don't support it. If you have ISA, say Y, otherwise N.
+
+config GENERIC_ISA_DMA
+ bool
+ depends on Q40 || AMIGA_PCMCIA || GG2
+ default y
+
+source "drivers/pci/Kconfig"
+
+source "drivers/zorro/Kconfig"
+
+endmenu
+
+source "drivers/Kconfig"
+
+menu "Character devices"
+
+config ATARI_MFPSER
+ tristate "Atari MFP serial support"
+ depends on ATARI
+ ---help---
+ If you like to use the MFP serial ports ("Modem1", "Serial1") under
+ Linux, say Y. The driver equally supports all kinds of MFP serial
+ ports and automatically detects whether Serial1 is available.
+
+ To compile this driver as a module, choose M here.
+
+ Note for Falcon users: You also have an MFP port, it's just not
+ wired to the outside... But you could use the port under Linux.
+
+config ATARI_SCC
+ tristate "Atari SCC serial support"
+ depends on ATARI
+ ---help---
+ If you have serial ports based on a Zilog SCC chip (Modem2, Serial2,
+ LAN) and like to use them under Linux, say Y. All built-in SCC's are
+ supported (TT, MegaSTE, Falcon), and also the ST-ESCC. If you have
+ two connectors for channel A (Serial2 and LAN), they are visible as
+ two separate devices.
+
+ To compile this driver as a module, choose M here.
+
+config ATARI_SCC_DMA
+ bool "Atari SCC serial DMA support"
+ depends on ATARI_SCC
+ help
+ This enables DMA support for receiving data on channel A of the SCC.
+ If you have a TT you may say Y here and read
+ drivers/char/atari_SCC.README. All other users should say N here,
+ because only the TT has SCC-DMA, even if your machine keeps claiming
+ so at boot time.
+
+config ATARI_MIDI
+ tristate "Atari MIDI serial support"
+ depends on ATARI
+ help
+ If you want to use your Atari's MIDI port in Linux, say Y.
+
+ To compile this driver as a module, choose M here.
+
+config ATARI_DSP56K
+ tristate "Atari DSP56k support (EXPERIMENTAL)"
+ depends on ATARI && EXPERIMENTAL
+ help
+ If you want to be able to use the DSP56001 in Falcons, say Y. This
+ driver is still experimental, and if you don't know what it is, or
+ if you don't have this processor, just say N.
+
+ To compile this driver as a module, choose M here.
+
+config AMIGA_BUILTIN_SERIAL
+ tristate "Amiga builtin serial support"
+ depends on AMIGA
+ help
+ If you want to use your Amiga's built-in serial port in Linux,
+ answer Y.
+
+ To compile this driver as a module, choose M here.
+
+config WHIPPET_SERIAL
+ tristate "Hisoft Whippet PCMCIA serial support"
+ depends on AMIGA_PCMCIA
+ help
+ HiSoft has a web page at <http://www.hisoft.co.uk/>, but there
+ is no listing for the Whippet in their Amiga section.
+
+config MULTIFACE_III_TTY
+ tristate "Multiface Card III serial support"
+ depends on AMIGA
+ help
+ If you want to use a Multiface III card's serial port in Linux,
+ answer Y.
+
+ To compile this driver as a module, choose M here.
+
+config GVPIOEXT
+ tristate "GVP IO-Extender support"
+ depends on PARPORT=n && ZORRO
+ help
+ If you want to use a GVP IO-Extender serial card in Linux, say Y.
+ Otherwise, say N.
+
+config GVPIOEXT_LP
+ tristate "GVP IO-Extender parallel printer support"
+ depends on GVPIOEXT
+ help
+ Say Y to enable driving a printer from the parallel port on your
+ GVP IO-Extender card, N otherwise.
+
+config GVPIOEXT_PLIP
+ tristate "GVP IO-Extender PLIP support"
+ depends on GVPIOEXT
+ help
+ Say Y to enable doing IP over the parallel port on your GVP
+ IO-Extender card, N otherwise.
+
+config MAC_SCC
+ tristate "Macintosh serial support"
+ depends on MAC
+
+config MAC_HID
+ bool
+ depends on INPUT_ADBHID
+ default y
+
+config MAC_ADBKEYCODES
+ bool "Support for ADB raw keycodes"
+ depends on INPUT_ADBHID
+ help
+ This provides support for sending raw ADB keycodes to console
+ devices. This is the default up to 2.4.0, but in future this may be
+ phased out in favor of generic Linux keycodes. If you say Y here,
+ you can dynamically switch via the
+ /proc/sys/dev/mac_hid/keyboard_sends_linux_keycodes
+ sysctl and with the "keyboard_sends_linux_keycodes=" kernel
+ argument.
+
+ If unsure, say Y here.
+
+config ADB_KEYBOARD
+ bool "Support for ADB keyboard (old driver)"
+ depends on MAC && !INPUT_ADBHID
+ help
+ This option allows you to use an ADB keyboard attached to your
+ machine. Note that this disables any other (ie. PS/2) keyboard
+ support, even if your machine is physically capable of using both at
+ the same time.
+
+ If you use an ADB keyboard (4 pin connector), say Y here.
+ If you use a PS/2 keyboard (6 pin connector), say N here.
+
+config HPDCA
+ tristate "HP DCA serial support"
+ depends on DIO && SERIAL_8250
+ help
+ If you want to use the internal "DCA" serial ports on an HP300
+ machine, say Y here.
+
+config HPAPCI
+ tristate "HP APCI serial support"
+ depends on HP300 && SERIAL_8250 && EXPERIMENTAL
+ help
+ If you want to use the internal "APCI" serial ports on an HP400
+ machine, say Y here.
+
+config MVME147_SCC
+ bool "SCC support for MVME147 serial ports"
+ depends on MVME147
+ help
+ This is the driver for the serial ports on the Motorola MVME147
+ boards. Everyone using one of these boards should say Y here.
+
+config SERIAL167
+ bool "CD2401 support for MVME166/7 serial ports"
+ depends on MVME16x && BROKEN
+ help
+ This is the driver for the serial ports on the Motorola MVME166,
+ 167, and 172 boards. Everyone using one of these boards should say
+ Y here.
+
+config MVME162_SCC
+ bool "SCC support for MVME162 serial ports"
+ depends on MVME16x
+ help
+ This is the driver for the serial ports on the Motorola MVME162 and
+ 172 boards. Everyone using one of these boards should say Y here.
+
+config BVME6000_SCC
+ bool "SCC support for BVME6000 serial ports"
+ depends on BVME6000
+ help
+ This is the driver for the serial ports on the BVME4000 and BVME6000
+ boards from BVM Ltd. Everyone using one of these boards should say
+ Y here.
+
+config DN_SERIAL
+ bool "Support for DN serial port (dummy)"
+ depends on APOLLO
+
+config SERIAL_CONSOLE
+ bool "Support for serial port console"
+ depends on (AMIGA || ATARI || MAC || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_SCC=y || ATARI_MIDI=y || MAC_SCC=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
+ ---help---
+ If you say Y here, it will be possible to use a serial port as the
+ system console (the system console is the device which receives all
+ kernel messages and warnings and which allows logins in single user
+ mode). This could be useful if some terminal or printer is connected
+ to that serial port.
+
+ Even if you say Y here, the currently visible virtual console
+ (/dev/tty0) will still be used as the system console by default, but
+ you can alter that using a kernel command line option such as
+ "console=ttyS1". (Try "man bootparam" or see the documentation of
+ your boot loader (lilo or loadlin) about how to pass options to the
+ kernel at boot time.)
+
+ If you don't have a VGA card installed and you say Y here, the
+ kernel will automatically use the first serial line, /dev/ttyS0, as
+ system console.
+
+ If unsure, say N.
+
+endmenu
+
+source "fs/Kconfig"
+
+source "arch/m68k/Kconfig.debug"
+
+source "security/Kconfig"
+
+source "crypto/Kconfig"
+
+source "lib/Kconfig"