Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/arch/ppc/boot/simple/m8xx_tty.c b/arch/ppc/boot/simple/m8xx_tty.c
new file mode 100644
index 0000000..1d2778e
--- /dev/null
+++ b/arch/ppc/boot/simple/m8xx_tty.c
@@ -0,0 +1,290 @@
+/* Minimal serial functions needed to send messages out the serial
+ * port on the MBX console.
+ *
+ * The MBX uxes SMC1 for the serial port. We reset the port and use
+ * only the first BD that EPPC-Bug set up as a character FIFO.
+ *
+ * Later versions (at least 1.4, maybe earlier) of the MBX EPPC-Bug
+ * use COM1 instead of SMC1 as the console port. This kinda sucks
+ * for the rest of the kernel, so here we force the use of SMC1 again.
+ */
+#include <linux/config.h>
+#include <linux/types.h>
+#include <asm/uaccess.h>
+#include <asm/mpc8xx.h>
+#include <asm/commproc.h>
+
+#ifdef CONFIG_MBX
+#define MBX_CSR1 ((volatile u_char *)0xfa100000)
+#define CSR1_COMEN (u_char)0x02
+#endif
+
+#ifdef TQM_SMC2_CONSOLE
+#define PROFF_CONS PROFF_SMC2
+#define CPM_CR_CH_CONS CPM_CR_CH_SMC2
+#define SMC_INDEX 1
+static volatile iop8xx_t *iopp = (iop8xx_t *)&(((immap_t *)IMAP_ADDR)->im_ioport);
+#else
+#define PROFF_CONS PROFF_SMC1
+#define CPM_CR_CH_CONS CPM_CR_CH_SMC1
+#define SMC_INDEX 0
+#endif
+
+static cpm8xx_t *cpmp = (cpm8xx_t *)&(((immap_t *)IMAP_ADDR)->im_cpm);
+
+unsigned long
+serial_init(int ignored, bd_t *bd)
+{
+ volatile smc_t *sp;
+ volatile smc_uart_t *up;
+ volatile cbd_t *tbdf, *rbdf;
+ volatile cpm8xx_t *cp;
+ uint dpaddr, memaddr;
+#ifndef CONFIG_MBX
+ uint ui;
+#endif
+
+ cp = cpmp;
+ sp = (smc_t*)&(cp->cp_smc[SMC_INDEX]);
+ up = (smc_uart_t *)&cp->cp_dparam[PROFF_CONS];
+
+ /* Disable transmitter/receiver.
+ */
+ sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
+
+#ifdef CONFIG_FADS
+ /* Enable SMC1/2 transceivers.
+ */
+ *((volatile uint *)BCSR1) &= ~(BCSR1_RS232EN_1|BCSR1_RS232EN_2);
+#endif
+
+#ifndef CONFIG_MBX
+ {
+ /* Initialize SMCx and use it for the console port.
+ */
+
+ /* Enable SDMA.
+ */
+ ((immap_t *)IMAP_ADDR)->im_siu_conf.sc_sdcr = 1;
+
+#ifdef TQM_SMC2_CONSOLE
+ /* Use Port A for SMC2 instead of other functions.
+ */
+ iopp->iop_papar |= 0x00c0;
+ iopp->iop_padir &= ~0x00c0;
+ iopp->iop_paodr &= ~0x00c0;
+#else
+ /* Use Port B for SMCs instead of other functions.
+ */
+ cp->cp_pbpar |= 0x00000cc0;
+ cp->cp_pbdir &= ~0x00000cc0;
+ cp->cp_pbodr &= ~0x00000cc0;
+#endif
+
+ /* Allocate space for two buffer descriptors in the DP ram.
+ * For now, this address seems OK, but it may have to
+ * change with newer versions of the firmware.
+ */
+ dpaddr = 0x0800;
+
+ /* Grab a few bytes from the top of memory for SMC FIFOs.
+ */
+ memaddr = (bd->bi_memsize - 32) & ~15;
+
+ /* Set the physical address of the host memory buffers in
+ * the buffer descriptors.
+ */
+ rbdf = (cbd_t *)&cp->cp_dpmem[dpaddr];
+ rbdf->cbd_bufaddr = memaddr;
+ rbdf->cbd_sc = 0;
+ tbdf = rbdf + 1;
+ tbdf->cbd_bufaddr = memaddr+4;
+ tbdf->cbd_sc = 0;
+
+ /* Set up the uart parameters in the parameter ram.
+ */
+ up->smc_rbase = dpaddr;
+ up->smc_tbase = dpaddr+sizeof(cbd_t);
+ up->smc_rfcr = SMC_EB;
+ up->smc_tfcr = SMC_EB;
+
+ /* Set UART mode, 8 bit, no parity, one stop.
+ * Enable receive and transmit.
+ */
+ sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
+
+ /* Mask all interrupts and remove anything pending.
+ */
+ sp->smc_smcm = 0;
+ sp->smc_smce = 0xff;
+
+ /* Set up the baud rate generator.
+ * See 8xx_io/commproc.c for details.
+ * This wires BRG1 to SMC1 and BRG2 to SMC2;
+ */
+ cp->cp_simode = 0x10000000;
+ ui = bd->bi_intfreq / 16 / bd->bi_baudrate;
+#ifdef TQM_SMC2_CONSOLE
+ cp->cp_brgc2 =
+#else
+ cp->cp_brgc1 =
+#endif
+ ((ui - 1) < 4096)
+ ? (((ui - 1) << 1) | CPM_BRG_EN)
+ : ((((ui / 16) - 1) << 1) | CPM_BRG_EN | CPM_BRG_DIV16);
+
+#else /* CONFIG_MBX */
+ if (*MBX_CSR1 & CSR1_COMEN) {
+ /* COM1 is enabled. Initialize SMC1 and use it for
+ * the console port.
+ */
+
+ /* Enable SDMA.
+ */
+ ((immap_t *)IMAP_ADDR)->im_siu_conf.sc_sdcr = 1;
+
+ /* Use Port B for SMCs instead of other functions.
+ */
+ cp->cp_pbpar |= 0x00000cc0;
+ cp->cp_pbdir &= ~0x00000cc0;
+ cp->cp_pbodr &= ~0x00000cc0;
+
+ /* Allocate space for two buffer descriptors in the DP ram.
+ * For now, this address seems OK, but it may have to
+ * change with newer versions of the firmware.
+ */
+ dpaddr = 0x0800;
+
+ /* Grab a few bytes from the top of memory. EPPC-Bug isn't
+ * running any more, so we can do this.
+ */
+ memaddr = (bd->bi_memsize - 32) & ~15;
+
+ /* Set the physical address of the host memory buffers in
+ * the buffer descriptors.
+ */
+ rbdf = (cbd_t *)&cp->cp_dpmem[dpaddr];
+ rbdf->cbd_bufaddr = memaddr;
+ rbdf->cbd_sc = 0;
+ tbdf = rbdf + 1;
+ tbdf->cbd_bufaddr = memaddr+4;
+ tbdf->cbd_sc = 0;
+
+ /* Set up the uart parameters in the parameter ram.
+ */
+ up->smc_rbase = dpaddr;
+ up->smc_tbase = dpaddr+sizeof(cbd_t);
+ up->smc_rfcr = SMC_EB;
+ up->smc_tfcr = SMC_EB;
+
+ /* Set UART mode, 8 bit, no parity, one stop.
+ * Enable receive and transmit.
+ */
+ sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
+
+ /* Mask all interrupts and remove anything pending.
+ */
+ sp->smc_smcm = 0;
+ sp->smc_smce = 0xff;
+
+ /* Set up the baud rate generator.
+ * See 8xx_io/commproc.c for details.
+ */
+ cp->cp_simode = 0x10000000;
+ cp->cp_brgc1 =
+ (((bd->bi_intfreq/16) / 9600) << 1) | CPM_BRG_EN;
+
+ /* Enable SMC1 for console output.
+ */
+ *MBX_CSR1 &= ~CSR1_COMEN;
+ }
+ else {
+#endif /* ndef CONFIG_MBX */
+ /* SMCx is used as console port.
+ */
+ tbdf = (cbd_t *)&cp->cp_dpmem[up->smc_tbase];
+ rbdf = (cbd_t *)&cp->cp_dpmem[up->smc_rbase];
+
+ /* Issue a stop transmit, and wait for it.
+ */
+ cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_CONS,
+ CPM_CR_STOP_TX) | CPM_CR_FLG;
+ while (cp->cp_cpcr & CPM_CR_FLG);
+ }
+
+ /* Make the first buffer the only buffer.
+ */
+ tbdf->cbd_sc |= BD_SC_WRAP;
+ rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
+
+ /* Single character receive.
+ */
+ up->smc_mrblr = 1;
+ up->smc_maxidl = 0;
+
+ /* Initialize Tx/Rx parameters.
+ */
+ cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_CONS, CPM_CR_INIT_TRX) | CPM_CR_FLG;
+ while (cp->cp_cpcr & CPM_CR_FLG);
+
+ /* Enable transmitter/receiver.
+ */
+ sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
+
+ /* This is ignored.
+ */
+ return 0;
+}
+
+void
+serial_putc(void *ignored, const char c)
+{
+ volatile cbd_t *tbdf;
+ volatile char *buf;
+ volatile smc_uart_t *up;
+
+ up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_CONS];
+ tbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_tbase];
+
+ /* Wait for last character to go.
+ */
+ buf = (char *)tbdf->cbd_bufaddr;
+ while (tbdf->cbd_sc & BD_SC_READY);
+
+ *buf = c;
+ tbdf->cbd_datlen = 1;
+ tbdf->cbd_sc |= BD_SC_READY;
+}
+
+char
+serial_getc(void *ignored)
+{
+ volatile cbd_t *rbdf;
+ volatile char *buf;
+ volatile smc_uart_t *up;
+ char c;
+
+ up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_CONS];
+ rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
+
+ /* Wait for character to show up.
+ */
+ buf = (char *)rbdf->cbd_bufaddr;
+ while (rbdf->cbd_sc & BD_SC_EMPTY);
+ c = *buf;
+ rbdf->cbd_sc |= BD_SC_EMPTY;
+
+ return(c);
+}
+
+int
+serial_tstc(void *ignored)
+{
+ volatile cbd_t *rbdf;
+ volatile smc_uart_t *up;
+
+ up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_CONS];
+ rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
+
+ return(!(rbdf->cbd_sc & BD_SC_EMPTY));
+}