Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/char/mxser.h b/drivers/char/mxser.h
new file mode 100644
index 0000000..e7fd0b0
--- /dev/null
+++ b/drivers/char/mxser.h
@@ -0,0 +1,450 @@
+#ifndef _MXSER_H
+#define _MXSER_H
+
+/*
+ * Semi-public control interfaces
+ */
+
+/*
+ * MOXA ioctls
+ */
+
+#define MOXA 0x400
+#define MOXA_GETDATACOUNT (MOXA + 23)
+#define MOXA_GET_CONF (MOXA + 35)
+#define MOXA_DIAGNOSE (MOXA + 50)
+#define MOXA_CHKPORTENABLE (MOXA + 60)
+#define MOXA_HighSpeedOn (MOXA + 61)
+#define MOXA_GET_MAJOR (MOXA + 63)
+#define MOXA_GET_CUMAJOR (MOXA + 64)
+#define MOXA_GETMSTATUS (MOXA + 65)
+#define MOXA_SET_OP_MODE (MOXA + 66)
+#define MOXA_GET_OP_MODE (MOXA + 67)
+
+#define RS232_MODE 0
+#define RS485_2WIRE_MODE 1
+#define RS422_MODE 2
+#define RS485_4WIRE_MODE 3
+#define OP_MODE_MASK 3
+// above add by Victor Yu. 01-05-2004
+
+#define TTY_THRESHOLD_THROTTLE 128
+
+#define LO_WATER (TTY_FLIPBUF_SIZE)
+#define HI_WATER (TTY_FLIPBUF_SIZE*2*3/4)
+
+// added by James. 03-11-2004.
+#define MOXA_SDS_GETICOUNTER (MOXA + 68)
+#define MOXA_SDS_RSTICOUNTER (MOXA + 69)
+// (above) added by James.
+
+#define MOXA_ASPP_OQUEUE (MOXA + 70)
+#define MOXA_ASPP_SETBAUD (MOXA + 71)
+#define MOXA_ASPP_GETBAUD (MOXA + 72)
+#define MOXA_ASPP_MON (MOXA + 73)
+#define MOXA_ASPP_LSTATUS (MOXA + 74)
+#define MOXA_ASPP_MON_EXT (MOXA + 75)
+#define MOXA_SET_BAUD_METHOD (MOXA + 76)
+
+
+/* --------------------------------------------------- */
+
+#define NPPI_NOTIFY_PARITY 0x01
+#define NPPI_NOTIFY_FRAMING 0x02
+#define NPPI_NOTIFY_HW_OVERRUN 0x04
+#define NPPI_NOTIFY_SW_OVERRUN 0x08
+#define NPPI_NOTIFY_BREAK 0x10
+
+#define NPPI_NOTIFY_CTSHOLD 0x01 // Tx hold by CTS low
+#define NPPI_NOTIFY_DSRHOLD 0x02 // Tx hold by DSR low
+#define NPPI_NOTIFY_XOFFHOLD 0x08 // Tx hold by Xoff received
+#define NPPI_NOTIFY_XOFFXENT 0x10 // Xoff Sent
+
+//CheckIsMoxaMust return value
+#define MOXA_OTHER_UART 0x00
+#define MOXA_MUST_MU150_HWID 0x01
+#define MOXA_MUST_MU860_HWID 0x02
+
+// follow just for Moxa Must chip define.
+//
+// when LCR register (offset 0x03) write following value,
+// the Must chip will enter enchance mode. And write value
+// on EFR (offset 0x02) bit 6,7 to change bank.
+#define MOXA_MUST_ENTER_ENCHANCE 0xBF
+
+// when enhance mode enable, access on general bank register
+#define MOXA_MUST_GDL_REGISTER 0x07
+#define MOXA_MUST_GDL_MASK 0x7F
+#define MOXA_MUST_GDL_HAS_BAD_DATA 0x80
+
+#define MOXA_MUST_LSR_RERR 0x80 // error in receive FIFO
+// enchance register bank select and enchance mode setting register
+// when LCR register equal to 0xBF
+#define MOXA_MUST_EFR_REGISTER 0x02
+// enchance mode enable
+#define MOXA_MUST_EFR_EFRB_ENABLE 0x10
+// enchance reister bank set 0, 1, 2
+#define MOXA_MUST_EFR_BANK0 0x00
+#define MOXA_MUST_EFR_BANK1 0x40
+#define MOXA_MUST_EFR_BANK2 0x80
+#define MOXA_MUST_EFR_BANK3 0xC0
+#define MOXA_MUST_EFR_BANK_MASK 0xC0
+
+// set XON1 value register, when LCR=0xBF and change to bank0
+#define MOXA_MUST_XON1_REGISTER 0x04
+
+// set XON2 value register, when LCR=0xBF and change to bank0
+#define MOXA_MUST_XON2_REGISTER 0x05
+
+// set XOFF1 value register, when LCR=0xBF and change to bank0
+#define MOXA_MUST_XOFF1_REGISTER 0x06
+
+// set XOFF2 value register, when LCR=0xBF and change to bank0
+#define MOXA_MUST_XOFF2_REGISTER 0x07
+
+#define MOXA_MUST_RBRTL_REGISTER 0x04
+#define MOXA_MUST_RBRTH_REGISTER 0x05
+#define MOXA_MUST_RBRTI_REGISTER 0x06
+#define MOXA_MUST_THRTL_REGISTER 0x07
+#define MOXA_MUST_ENUM_REGISTER 0x04
+#define MOXA_MUST_HWID_REGISTER 0x05
+#define MOXA_MUST_ECR_REGISTER 0x06
+#define MOXA_MUST_CSR_REGISTER 0x07
+
+// good data mode enable
+#define MOXA_MUST_FCR_GDA_MODE_ENABLE 0x20
+// only good data put into RxFIFO
+#define MOXA_MUST_FCR_GDA_ONLY_ENABLE 0x10
+
+// enable CTS interrupt
+#define MOXA_MUST_IER_ECTSI 0x80
+// eanble RTS interrupt
+#define MOXA_MUST_IER_ERTSI 0x40
+// enable Xon/Xoff interrupt
+#define MOXA_MUST_IER_XINT 0x20
+// enable GDA interrupt
+#define MOXA_MUST_IER_EGDAI 0x10
+
+#define MOXA_MUST_RECV_ISR (UART_IER_RDI | MOXA_MUST_IER_EGDAI)
+
+// GDA interrupt pending
+#define MOXA_MUST_IIR_GDA 0x1C
+#define MOXA_MUST_IIR_RDA 0x04
+#define MOXA_MUST_IIR_RTO 0x0C
+#define MOXA_MUST_IIR_LSR 0x06
+
+// recieved Xon/Xoff or specical interrupt pending
+#define MOXA_MUST_IIR_XSC 0x10
+
+// RTS/CTS change state interrupt pending
+#define MOXA_MUST_IIR_RTSCTS 0x20
+#define MOXA_MUST_IIR_MASK 0x3E
+
+#define MOXA_MUST_MCR_XON_FLAG 0x40
+#define MOXA_MUST_MCR_XON_ANY 0x80
+#define MOXA_MUST_MCR_TX_XON 0x08
+
+
+// software flow control on chip mask value
+#define MOXA_MUST_EFR_SF_MASK 0x0F
+// send Xon1/Xoff1
+#define MOXA_MUST_EFR_SF_TX1 0x08
+// send Xon2/Xoff2
+#define MOXA_MUST_EFR_SF_TX2 0x04
+// send Xon1,Xon2/Xoff1,Xoff2
+#define MOXA_MUST_EFR_SF_TX12 0x0C
+// don't send Xon/Xoff
+#define MOXA_MUST_EFR_SF_TX_NO 0x00
+// Tx software flow control mask
+#define MOXA_MUST_EFR_SF_TX_MASK 0x0C
+// don't receive Xon/Xoff
+#define MOXA_MUST_EFR_SF_RX_NO 0x00
+// receive Xon1/Xoff1
+#define MOXA_MUST_EFR_SF_RX1 0x02
+// receive Xon2/Xoff2
+#define MOXA_MUST_EFR_SF_RX2 0x01
+// receive Xon1,Xon2/Xoff1,Xoff2
+#define MOXA_MUST_EFR_SF_RX12 0x03
+// Rx software flow control mask
+#define MOXA_MUST_EFR_SF_RX_MASK 0x03
+
+//#define MOXA_MUST_MIN_XOFFLIMIT 66
+//#define MOXA_MUST_MIN_XONLIMIT 20
+//#define ID1_RX_TRIG 120
+
+
+#define CHECK_MOXA_MUST_XOFFLIMIT(info) { \
+ if ( (info)->IsMoxaMustChipFlag && \
+ (info)->HandFlow.XoffLimit < MOXA_MUST_MIN_XOFFLIMIT ) { \
+ (info)->HandFlow.XoffLimit = MOXA_MUST_MIN_XOFFLIMIT; \
+ (info)->HandFlow.XonLimit = MOXA_MUST_MIN_XONLIMIT; \
+ } \
+}
+
+#define ENABLE_MOXA_MUST_ENCHANCE_MODE(baseio) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr |= MOXA_MUST_EFR_EFRB_ENABLE; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define DISABLE_MOXA_MUST_ENCHANCE_MODE(baseio) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_EFRB_ENABLE; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define SET_MOXA_MUST_XON1_VALUE(baseio, Value) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK0; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb((u8)(Value), (baseio)+MOXA_MUST_XON1_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define SET_MOXA_MUST_XON2_VALUE(baseio, Value) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK0; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb((u8)(Value), (baseio)+MOXA_MUST_XON2_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define SET_MOXA_MUST_XOFF1_VALUE(baseio, Value) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK0; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb((u8)(Value), (baseio)+MOXA_MUST_XOFF1_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define SET_MOXA_MUST_XOFF2_VALUE(baseio, Value) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK0; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb((u8)(Value), (baseio)+MOXA_MUST_XOFF2_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define SET_MOXA_MUST_RBRTL_VALUE(baseio, Value) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK1; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb((u8)(Value), (baseio)+MOXA_MUST_RBRTL_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define SET_MOXA_MUST_RBRTH_VALUE(baseio, Value) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK1; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb((u8)(Value), (baseio)+MOXA_MUST_RBRTH_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define SET_MOXA_MUST_RBRTI_VALUE(baseio, Value) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK1; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb((u8)(Value), (baseio)+MOXA_MUST_RBRTI_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define SET_MOXA_MUST_THRTL_VALUE(baseio, Value) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK1; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb((u8)(Value), (baseio)+MOXA_MUST_THRTL_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+//#define MOXA_MUST_RBRL_VALUE 4
+#define SET_MOXA_MUST_FIFO_VALUE(info) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((info)->base+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (info)->base+UART_LCR); \
+ __efr = inb((info)->base+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK1; \
+ outb(__efr, (info)->base+MOXA_MUST_EFR_REGISTER); \
+ outb((u8)((info)->rx_high_water), (info)->base+MOXA_MUST_RBRTH_REGISTER); \
+ outb((u8)((info)->rx_trigger), (info)->base+MOXA_MUST_RBRTI_REGISTER); \
+ outb((u8)((info)->rx_low_water), (info)->base+MOXA_MUST_RBRTL_REGISTER); \
+ outb(__oldlcr, (info)->base+UART_LCR); \
+}
+
+
+
+#define SET_MOXA_MUST_ENUM_VALUE(baseio, Value) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK2; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb((u8)(Value), (baseio)+MOXA_MUST_ENUM_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define GET_MOXA_MUST_HARDWARE_ID(baseio, pId) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK2; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ *pId = inb((baseio)+MOXA_MUST_HWID_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(baseio) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_MASK; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define SET_MOXA_MUST_JUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_MASK; \
+ __efr |= MOXA_MUST_EFR_SF_TX1; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \
+ __efr |= MOXA_MUST_EFR_SF_TX1; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define SET_MOXA_MUST_JUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_MASK; \
+ __efr |= MOXA_MUST_EFR_SF_RX1; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \
+ __efr |= MOXA_MUST_EFR_SF_RX1; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define ENABLE_MOXA_MUST_TX_RX_SOFTWARE_FLOW_CONTROL(baseio) { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_MASK; \
+ __efr |= (MOXA_MUST_EFR_SF_RX1|MOXA_MUST_EFR_SF_TX1); \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+}
+
+#define ENABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(baseio) { \
+ u8 __oldmcr; \
+ __oldmcr = inb((baseio)+UART_MCR); \
+ __oldmcr |= MOXA_MUST_MCR_XON_ANY; \
+ outb(__oldmcr, (baseio)+UART_MCR); \
+}
+
+#define DISABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(baseio) { \
+ u8 __oldmcr; \
+ __oldmcr = inb((baseio)+UART_MCR); \
+ __oldmcr &= ~MOXA_MUST_MCR_XON_ANY; \
+ outb(__oldmcr, (baseio)+UART_MCR); \
+}
+
+#define READ_MOXA_MUST_GDL(baseio) inb((baseio)+MOXA_MUST_GDL_REGISTER)
+
+
+#ifndef INIT_WORK
+#define INIT_WORK(_work, _func, _data){ \
+ _data->tqueue.routine = _func;\
+ _data->tqueue.data = _data;\
+ }
+#endif
+
+#endif