Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/isdn/hisax/Kconfig b/drivers/isdn/hisax/Kconfig
new file mode 100644
index 0000000..6c7b8bf
--- /dev/null
+++ b/drivers/isdn/hisax/Kconfig
@@ -0,0 +1,442 @@
+
+menu "Passive cards"
+ depends on ISDN_I4L
+
+config ISDN_DRV_HISAX
+ tristate "HiSax SiemensChipSet driver support"
+ select CRC_CCITT
+ ---help---
+ This is a driver supporting the Siemens chipset on various
+ ISDN-cards (like AVM A1, Elsa ISDN cards, Teles S0-16.0, Teles
+ S0-16.3, Teles S0-8, Teles/Creatix PnP, ITK micro ix1 and many
+ compatibles).
+
+ HiSax is just the name of this driver, not the name of any hardware.
+
+ If you have a card with such a chipset, you should say Y here and
+ also to the configuration option of the driver for your particular
+ card, below.
+
+if ISDN_DRV_HISAX!=n
+
+comment "D-channel protocol features"
+
+config HISAX_EURO
+ bool "HiSax Support for EURO/DSS1"
+ help
+ Say Y or N according to the D-channel protocol which your local
+ telephone service company provides.
+
+ The call control protocol E-DSS1 is used in most European countries.
+ If unsure, say Y.
+
+config DE_AOC
+ bool "Support for german chargeinfo"
+ depends on HISAX_EURO
+ help
+ If you want that the HiSax hardware driver sends messages to the
+ upper level of the isdn code on each AOCD (Advice Of Charge, During
+ the call -- transmission of the fee information during a call) and
+ on each AOCE (Advice Of Charge, at the End of the call --
+ transmission of fee information at the end of the call), say Y here.
+ This works only in Germany.
+
+config HISAX_NO_SENDCOMPLETE
+ bool "Disable sending complete"
+ depends on HISAX_EURO
+ help
+ If you have trouble with some ugly exchanges or you live in
+ Australia select this option.
+
+config HISAX_NO_LLC
+ bool "Disable sending low layer compatibility"
+ depends on HISAX_EURO
+ help
+ If you have trouble with some ugly exchanges try to select this
+ option.
+
+config HISAX_NO_KEYPAD
+ bool "Disable keypad protocol option"
+ depends on HISAX_EURO
+ help
+ If you like to send special dial strings including * or # without
+ using the keypad protocol, select this option.
+
+config HISAX_1TR6
+ bool "HiSax Support for german 1TR6"
+ help
+ Say Y or N according to the D-channel protocol which your local
+ telephone service company provides.
+
+ 1TR6 is an old call control protocol which was used in Germany
+ before E-DSS1 was established. Nowadays, all new lines in Germany
+ use E-DSS1.
+
+config HISAX_NI1
+ bool "HiSax Support for US NI1"
+ help
+ Enable this if you like to use ISDN in US on a NI1 basic rate
+ interface.
+
+config HISAX_MAX_CARDS
+ int "Maximum number of cards supported by HiSax"
+ default "8"
+ help
+ This option allows you to specify the maximum number of cards which
+ the HiSax driver will be able to handle.
+
+comment "HiSax supported cards"
+
+config HISAX_16_0
+ bool "Teles 16.0/8.0"
+ depends on ISA
+ help
+ This enables HiSax support for the Teles ISDN-cards S0-16.0, S0-8
+ and many compatibles.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using the different cards, a different D-channel protocol, or
+ non-standard IRQ/port/shmem settings.
+
+config HISAX_16_3
+ bool "Teles 16.3 or PNP or PCMCIA"
+ help
+ This enables HiSax support for the Teles ISDN-cards S0-16.3 the
+ Teles/Creatix PnP and the Teles PCMCIA.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using the different cards, a different D-channel protocol, or
+ non-standard IRQ/port settings.
+
+config HISAX_TELESPCI
+ bool "Teles PCI"
+ depends on PCI && (BROKEN || !(SPARC64 || PPC))
+ help
+ This enables HiSax support for the Teles PCI.
+ See <file:Documentation/isdn/README.HiSax> on how to configure it.
+
+config HISAX_S0BOX
+ bool "Teles S0Box"
+ help
+ This enables HiSax support for the Teles/Creatix parallel port
+ S0BOX. See <file:Documentation/isdn/README.HiSax> on how to
+ configure it.
+
+config HISAX_AVM_A1
+ bool "AVM A1 (Fritz)"
+ depends on ISA
+ help
+ This enables HiSax support for the AVM A1 (aka "Fritz").
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using the different cards, a different D-channel protocol, or
+ non-standard IRQ/port settings.
+
+config HISAX_FRITZPCI
+ bool "AVM PnP/PCI (Fritz!PnP/PCI)"
+ help
+ This enables HiSax support for the AVM "Fritz!PnP" and "Fritz!PCI".
+ See <file:Documentation/isdn/README.HiSax> on how to configure it.
+
+config HISAX_AVM_A1_PCMCIA
+ bool "AVM A1 PCMCIA (Fritz)"
+ help
+ This enables HiSax support for the AVM A1 "Fritz!PCMCIA").
+ See <file:Documentation/isdn/README.HiSax> on how to configure it.
+
+config HISAX_ELSA
+ bool "Elsa cards"
+ help
+ This enables HiSax support for the Elsa Mircolink ISA cards, for the
+ Elsa Quickstep series cards and Elsa PCMCIA.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using the different cards, a different D-channel protocol, or
+ non-standard IRQ/port settings.
+
+config HISAX_IX1MICROR2
+ bool "ITK ix1-micro Revision 2"
+ depends on ISA
+ help
+ This enables HiSax support for the ITK ix1-micro Revision 2 card.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using the different cards, a different D-channel protocol, or
+ non-standard IRQ/port settings.
+
+config HISAX_DIEHLDIVA
+ bool "Eicon.Diehl Diva cards"
+ help
+ This enables HiSax support for the Eicon.Diehl Diva none PRO
+ versions passive ISDN cards.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using the different cards, a different D-channel protocol, or
+ non-standard IRQ/port settings.
+
+config HISAX_ASUSCOM
+ bool "ASUSCOM ISA cards"
+ depends on ISA
+ help
+ This enables HiSax support for the AsusCom and their OEM versions
+ passive ISDN ISA cards.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using the different cards, a different D-channel protocol, or
+ non-standard IRQ/port settings.
+
+config HISAX_TELEINT
+ bool "TELEINT cards"
+ depends on ISA
+ help
+ This enables HiSax support for the TELEINT SA1 semiactiv ISDN card.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using the different cards, a different D-channel protocol, or
+ non-standard IRQ/port settings.
+
+config HISAX_HFCS
+ bool "HFC-S based cards"
+ depends on ISA
+ help
+ This enables HiSax support for the HFC-S 2BDS0 based cards, like
+ teles 16.3c.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using the different cards, a different D-channel protocol, or
+ non-standard IRQ/port settings.
+
+config HISAX_SEDLBAUER
+ bool "Sedlbauer cards"
+ help
+ This enables HiSax support for the Sedlbauer passive ISDN cards.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using the different cards, a different D-channel protocol, or
+ non-standard IRQ/port settings.
+
+config HISAX_SPORTSTER
+ bool "USR Sportster internal TA"
+ depends on ISA
+ help
+ This enables HiSax support for the USR Sportster internal TA card.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using a different D-channel protocol, or non-standard IRQ/port
+ settings.
+
+config HISAX_MIC
+ bool "MIC card"
+ depends on ISA
+ help
+ This enables HiSax support for the ITH MIC card.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using a different D-channel protocol, or non-standard IRQ/port
+ settings.
+
+config HISAX_NETJET
+ bool "NETjet card"
+ depends on PCI && (BROKEN || !(SPARC64 || PPC))
+ help
+ This enables HiSax support for the NetJet from Traverse
+ Technologies.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using a different D-channel protocol, or non-standard IRQ/port
+ settings.
+
+config HISAX_NETJET_U
+ bool "NETspider U card"
+ depends on PCI && (BROKEN || !(SPARC64 || PPC))
+ help
+ This enables HiSax support for the Netspider U interface ISDN card
+ from Traverse Technologies.
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using a different D-channel protocol, or non-standard IRQ/port
+ settings.
+
+config HISAX_NICCY
+ bool "Niccy PnP/PCI card"
+ help
+ This enables HiSax support for the Dr. Neuhaus Niccy PnP or PCI.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using a different D-channel protocol, or non-standard IRQ/port
+ settings.
+
+config HISAX_ISURF
+ bool "Siemens I-Surf card"
+ depends on ISA
+ help
+ This enables HiSax support for the Siemens I-Talk/I-Surf card with
+ ISAR chip.
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using a different D-channel protocol, or non-standard IRQ/port
+ settings.
+
+config HISAX_HSTSAPHIR
+ bool "HST Saphir card"
+ depends on ISA
+ help
+ This enables HiSax support for the HST Saphir card.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using a different D-channel protocol, or non-standard IRQ/port
+ settings.
+
+config HISAX_BKM_A4T
+ bool "Telekom A4T card"
+ depends on PCI
+ help
+ This enables HiSax support for the Telekom A4T card.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using a different D-channel protocol, or non-standard IRQ/port
+ settings.
+
+config HISAX_SCT_QUADRO
+ bool "Scitel Quadro card"
+ depends on PCI
+ help
+ This enables HiSax support for the Scitel Quadro card.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using a different D-channel protocol, or non-standard IRQ/port
+ settings.
+
+config HISAX_GAZEL
+ bool "Gazel cards"
+ help
+ This enables HiSax support for the Gazel cards.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using a different D-channel protocol, or non-standard IRQ/port
+ settings.
+
+config HISAX_HFC_PCI
+ bool "HFC PCI-Bus cards"
+ depends on PCI && (BROKEN || !(SPARC64 || PPC))
+ help
+ This enables HiSax support for the HFC-S PCI 2BDS0 based cards.
+
+ For more informations see under
+ <file:Documentation/isdn/README.hfc-pci>.
+
+config HISAX_W6692
+ bool "Winbond W6692 based cards"
+ depends on PCI
+ help
+ This enables HiSax support for Winbond W6692 based PCI ISDN cards.
+
+ See <file:Documentation/isdn/README.HiSax> on how to configure it
+ using a different D-channel protocol, or non-standard IRQ/port
+ settings.
+
+config HISAX_HFC_SX
+ bool "HFC-S+, HFC-SP, HFC-PCMCIA cards"
+ help
+ This enables HiSax support for the HFC-S+, HFC-SP and HFC-PCMCIA
+ cards. This code is not finished yet.
+
+# bool ' TESTEMULATOR (EXPERIMENTAL)' CONFIG_HISAX_TESTEMU
+
+config HISAX_ENTERNOW_PCI
+ bool "Formula-n enter:now PCI card"
+ depends on PCI && (BROKEN || !(SPARC64 || PPC))
+ help
+ This enables HiSax support for the Formula-n enter:now PCI
+ ISDN card.
+
+config HISAX_AMD7930
+ bool "Am7930 (EXPERIMENTAL)"
+ depends on EXPERIMENTAL && (SPARC32 || SPARC64)
+ help
+ This enables HiSax support for the AMD7930 chips on some SPARCs.
+ This code is not finished yet.
+
+endif
+
+if ISDN_DRV_HISAX
+
+config HISAX_DEBUG
+ bool "HiSax debugging"
+ help
+ This enables debugging code in the new-style HiSax drivers, i.e.
+ the ST5481 USB driver currently.
+ If in doubt, say yes.
+
+comment "HiSax PCMCIA card service modules"
+
+config HISAX_SEDLBAUER_CS
+ tristate "Sedlbauer PCMCIA cards"
+ depends on PCMCIA && HISAX_SEDLBAUER
+ help
+ This enables the PCMCIA client driver for the Sedlbauer Speed Star
+ and Speed Star II cards.
+
+config HISAX_ELSA_CS
+ tristate "ELSA PCMCIA MicroLink cards"
+ depends on PCMCIA && HISAX_ELSA
+ help
+ This enables the PCMCIA client driver for the Elsa PCMCIA MicroLink
+ card.
+
+config HISAX_AVM_A1_CS
+ tristate "AVM A1 PCMCIA cards"
+ depends on PCMCIA && ISDN_DRV_HISAX
+ help
+ This enables the PCMCIA client driver for the AVM A1 / Fritz!Card
+ PCMCIA cards.
+
+config HISAX_TELES_CS
+ tristate "TELES PCMCIA cards"
+ depends on PCMCIA && HISAX_16_3
+ help
+ This enables the PCMCIA client driver for the Teles PCMCIA cards.
+
+comment "HiSax sub driver modules"
+
+config HISAX_ST5481
+ tristate "ST5481 USB ISDN modem (EXPERIMENTAL)"
+ depends on USB && EXPERIMENTAL
+ select CRC_CCITT
+ help
+ This enables the driver for ST5481 based USB ISDN adapters,
+ e.g. the BeWan Gazel 128 USB
+
+config HISAX_HFCUSB
+ tristate "HFC USB based ISDN modems (EXPERIMENTAL)"
+ depends on USB && EXPERIMENTAL
+ help
+ This enables the driver for HFC USB based ISDN modems.
+
+config HISAX_HFC4S8S
+ tristate "HFC-4S/8S based ISDN cards (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ help
+ This enables the driver for HFC-4S/8S based ISDN cards.
+
+config HISAX_FRITZ_PCIPNP
+ tristate "AVM Fritz!Card PCI/PCIv2/PnP support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ help
+ This enables the driver for the AVM Fritz!Card PCI,
+ Fritz!Card PCI v2 and Fritz!Card PnP.
+ (the latter also needs you to select "ISA Plug and Play support"
+ from the menu "Plug and Play configuration")
+
+config HISAX_HDLC
+ bool
+ depends on HISAX_ST5481
+ default y
+
+config HISAX_AVM_A1_PCMCIA
+ bool
+ depends on HISAX_AVM_A1_CS
+ default y
+
+endif
+
+endmenu
+