diff --git a/drivers/net/cs89x0.h b/drivers/net/cs89x0.h
new file mode 100644
index 0000000..b0ef7ad
--- /dev/null
+++ b/drivers/net/cs89x0.h
@@ -0,0 +1,476 @@
+/*  Copyright, 1988-1992, Russell Nelson, Crynwr Software
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation, version 1.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program; if not, write to the Free Software
+   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+   */
+
+#include <linux/config.h>
+
+#ifdef CONFIG_ARCH_IXDP2X01
+/* IXDP2401/IXDP2801 uses dword-aligned register addressing */
+#define CS89x0_PORT(reg) ((reg) * 2)
+#else
+#define CS89x0_PORT(reg) (reg)
+#endif
+
+#define PP_ChipID 0x0000	/* offset   0h -> Corp -ID              */
+				/* offset   2h -> Model/Product Number  */
+				/* offset   3h -> Chip Revision Number  */
+
+#define PP_ISAIOB 0x0020	/*  IO base address */
+#define PP_CS8900_ISAINT 0x0022	/*  ISA interrupt select */
+#define PP_CS8920_ISAINT 0x0370	/*  ISA interrupt select */
+#define PP_CS8900_ISADMA 0x0024	/*  ISA Rec DMA channel */
+#define PP_CS8920_ISADMA 0x0374	/*  ISA Rec DMA channel */
+#define PP_ISASOF 0x0026	/*  ISA DMA offset */
+#define PP_DmaFrameCnt 0x0028	/*  ISA DMA Frame count */
+#define PP_DmaByteCnt 0x002A	/*  ISA DMA Byte count */
+#define PP_CS8900_ISAMemB 0x002C	/*  Memory base */
+#define PP_CS8920_ISAMemB 0x0348 /*  */
+
+#define PP_ISABootBase 0x0030	/*  Boot Prom base  */
+#define PP_ISABootMask 0x0034	/*  Boot Prom Mask */
+
+/* EEPROM data and command registers */
+#define PP_EECMD 0x0040		/*  NVR Interface Command register */
+#define PP_EEData 0x0042	/*  NVR Interface Data Register */
+#define PP_DebugReg 0x0044	/*  Debug Register */
+
+#define PP_RxCFG 0x0102		/*  Rx Bus config */
+#define PP_RxCTL 0x0104		/*  Receive Control Register */
+#define PP_TxCFG 0x0106		/*  Transmit Config Register */
+#define PP_TxCMD 0x0108		/*  Transmit Command Register */
+#define PP_BufCFG 0x010A	/*  Bus configuration Register */
+#define PP_LineCTL 0x0112	/*  Line Config Register */
+#define PP_SelfCTL 0x0114	/*  Self Command Register */
+#define PP_BusCTL 0x0116	/*  ISA bus control Register */
+#define PP_TestCTL 0x0118	/*  Test Register */
+#define PP_AutoNegCTL 0x011C	/*  Auto Negotiation Ctrl */
+
+#define PP_ISQ 0x0120		/*  Interrupt Status */
+#define PP_RxEvent 0x0124	/*  Rx Event Register */
+#define PP_TxEvent 0x0128	/*  Tx Event Register */
+#define PP_BufEvent 0x012C	/*  Bus Event Register */
+#define PP_RxMiss 0x0130	/*  Receive Miss Count */
+#define PP_TxCol 0x0132		/*  Transmit Collision Count */
+#define PP_LineST 0x0134	/*  Line State Register */
+#define PP_SelfST 0x0136	/*  Self State register */
+#define PP_BusST 0x0138		/*  Bus Status */
+#define PP_TDR 0x013C		/*  Time Domain Reflectometry */
+#define PP_AutoNegST 0x013E	/*  Auto Neg Status */
+#define PP_TxCommand 0x0144	/*  Tx Command */
+#define PP_TxLength 0x0146	/*  Tx Length */
+#define PP_LAF 0x0150		/*  Hash Table */
+#define PP_IA 0x0158		/*  Physical Address Register */
+
+#define PP_RxStatus 0x0400	/*  Receive start of frame */
+#define PP_RxLength 0x0402	/*  Receive Length of frame */
+#define PP_RxFrame 0x0404	/*  Receive frame pointer */
+#define PP_TxFrame 0x0A00	/*  Transmit frame pointer */
+
+/*  Primary I/O Base Address. If no I/O base is supplied by the user, then this */
+/*  can be used as the default I/O base to access the PacketPage Area. */
+#define DEFAULTIOBASE 0x0300
+#define FIRST_IO 0x020C		/*  First I/O port to check */
+#define LAST_IO 0x037C		/*  Last I/O port to check (+10h) */
+#define ADD_MASK 0x3000		/*  Mask it use of the ADD_PORT register */
+#define ADD_SIG 0x3000		/*  Expected ID signature */
+
+/* On Macs, we only need use the ISA I/O stuff until we do MEMORY_ON */
+#ifdef CONFIG_MAC
+#define LCSLOTBASE 0xfee00000
+#define MMIOBASE 0x40000
+#endif
+
+#define CHIP_EISA_ID_SIG 0x630E   /*  Product ID Code for Crystal Chip (CS8900 spec 4.3) */
+
+#ifdef IBMEIPKT
+#define EISA_ID_SIG 0x4D24	/*  IBM */
+#define PART_NO_SIG 0x1010	/*  IBM */
+#define MONGOOSE_BIT 0x0000	/*  IBM */
+#else
+#define EISA_ID_SIG 0x630E	/*  PnP Vendor ID (same as chip id for Crystal board) */
+#define PART_NO_SIG 0x4000	/*  ID code CS8920 board (PnP Vendor Product code) */
+#define MONGOOSE_BIT 0x2000	/*  PART_NO_SIG + MONGOOSE_BUT => ID of mongoose */
+#endif
+
+#define PRODUCT_ID_ADD 0x0002   /*  Address of product ID */
+
+/*  Mask to find out the types of  registers */
+#define REG_TYPE_MASK 0x001F
+
+/*  Eeprom Commands */
+#define ERSE_WR_ENBL 0x00F0
+#define ERSE_WR_DISABLE 0x0000
+
+/*  Defines Control/Config register quintuplet numbers */
+#define RX_BUF_CFG 0x0003
+#define RX_CONTROL 0x0005
+#define TX_CFG 0x0007
+#define TX_COMMAND 0x0009
+#define BUF_CFG 0x000B
+#define LINE_CONTROL 0x0013
+#define SELF_CONTROL 0x0015
+#define BUS_CONTROL 0x0017
+#define TEST_CONTROL 0x0019
+
+/*  Defines Status/Count registers quintuplet numbers */
+#define RX_EVENT 0x0004
+#define TX_EVENT 0x0008
+#define BUF_EVENT 0x000C
+#define RX_MISS_COUNT 0x0010
+#define TX_COL_COUNT 0x0012
+#define LINE_STATUS 0x0014
+#define SELF_STATUS 0x0016
+#define BUS_STATUS 0x0018
+#define TDR 0x001C
+
+/* PP_RxCFG - Receive  Configuration and Interrupt Mask bit definition -  Read/write */
+#define SKIP_1 0x0040
+#define RX_STREAM_ENBL 0x0080
+#define RX_OK_ENBL 0x0100
+#define RX_DMA_ONLY 0x0200
+#define AUTO_RX_DMA 0x0400
+#define BUFFER_CRC 0x0800
+#define RX_CRC_ERROR_ENBL 0x1000
+#define RX_RUNT_ENBL 0x2000
+#define RX_EXTRA_DATA_ENBL 0x4000
+
+/* PP_RxCTL - Receive Control bit definition - Read/write */
+#define RX_IA_HASH_ACCEPT 0x0040
+#define RX_PROM_ACCEPT 0x0080
+#define RX_OK_ACCEPT 0x0100
+#define RX_MULTCAST_ACCEPT 0x0200
+#define RX_IA_ACCEPT 0x0400
+#define RX_BROADCAST_ACCEPT 0x0800
+#define RX_BAD_CRC_ACCEPT 0x1000
+#define RX_RUNT_ACCEPT 0x2000
+#define RX_EXTRA_DATA_ACCEPT 0x4000
+#define RX_ALL_ACCEPT (RX_PROM_ACCEPT|RX_BAD_CRC_ACCEPT|RX_RUNT_ACCEPT|RX_EXTRA_DATA_ACCEPT)
+/*  Default receive mode - individually addressed, broadcast, and error free */
+#define DEF_RX_ACCEPT (RX_IA_ACCEPT | RX_BROADCAST_ACCEPT | RX_OK_ACCEPT)
+
+/* PP_TxCFG - Transmit Configuration Interrupt Mask bit definition - Read/write */
+#define TX_LOST_CRS_ENBL 0x0040
+#define TX_SQE_ERROR_ENBL 0x0080
+#define TX_OK_ENBL 0x0100
+#define TX_LATE_COL_ENBL 0x0200
+#define TX_JBR_ENBL 0x0400
+#define TX_ANY_COL_ENBL 0x0800
+#define TX_16_COL_ENBL 0x8000
+
+/* PP_TxCMD - Transmit Command bit definition - Read-only */
+#define TX_START_4_BYTES 0x0000
+#define TX_START_64_BYTES 0x0040
+#define TX_START_128_BYTES 0x0080
+#define TX_START_ALL_BYTES 0x00C0
+#define TX_FORCE 0x0100
+#define TX_ONE_COL 0x0200
+#define TX_TWO_PART_DEFF_DISABLE 0x0400
+#define TX_NO_CRC 0x1000
+#define TX_RUNT 0x2000
+
+/* PP_BufCFG - Buffer Configuration Interrupt Mask bit definition - Read/write */
+#define GENERATE_SW_INTERRUPT 0x0040
+#define RX_DMA_ENBL 0x0080
+#define READY_FOR_TX_ENBL 0x0100
+#define TX_UNDERRUN_ENBL 0x0200
+#define RX_MISS_ENBL 0x0400
+#define RX_128_BYTE_ENBL 0x0800
+#define TX_COL_COUNT_OVRFLOW_ENBL 0x1000
+#define RX_MISS_COUNT_OVRFLOW_ENBL 0x2000
+#define RX_DEST_MATCH_ENBL 0x8000
+
+/* PP_LineCTL - Line Control bit definition - Read/write */
+#define SERIAL_RX_ON 0x0040
+#define SERIAL_TX_ON 0x0080
+#define AUI_ONLY 0x0100
+#define AUTO_AUI_10BASET 0x0200
+#define MODIFIED_BACKOFF 0x0800
+#define NO_AUTO_POLARITY 0x1000
+#define TWO_PART_DEFDIS 0x2000
+#define LOW_RX_SQUELCH 0x4000
+
+/* PP_SelfCTL - Software Self Control bit definition - Read/write */
+#define POWER_ON_RESET 0x0040
+#define SW_STOP 0x0100
+#define SLEEP_ON 0x0200
+#define AUTO_WAKEUP 0x0400
+#define HCB0_ENBL 0x1000
+#define HCB1_ENBL 0x2000
+#define HCB0 0x4000
+#define HCB1 0x8000
+
+/* PP_BusCTL - ISA Bus Control bit definition - Read/write */
+#define RESET_RX_DMA 0x0040
+#define MEMORY_ON 0x0400
+#define DMA_BURST_MODE 0x0800
+#define IO_CHANNEL_READY_ON 0x1000
+#define RX_DMA_SIZE_64K 0x2000
+#define ENABLE_IRQ 0x8000
+
+/* PP_TestCTL - Test Control bit definition - Read/write */
+#define LINK_OFF 0x0080
+#define ENDEC_LOOPBACK 0x0200
+#define AUI_LOOPBACK 0x0400
+#define BACKOFF_OFF 0x0800
+#define FDX_8900 0x4000
+#define FAST_TEST 0x8000
+
+/* PP_RxEvent - Receive Event Bit definition - Read-only */
+#define RX_IA_HASHED 0x0040
+#define RX_DRIBBLE 0x0080
+#define RX_OK 0x0100
+#define RX_HASHED 0x0200
+#define RX_IA 0x0400
+#define RX_BROADCAST 0x0800
+#define RX_CRC_ERROR 0x1000
+#define RX_RUNT 0x2000
+#define RX_EXTRA_DATA 0x4000
+
+#define HASH_INDEX_MASK 0x0FC00
+
+/* PP_TxEvent - Transmit Event Bit definition - Read-only */
+#define TX_LOST_CRS 0x0040
+#define TX_SQE_ERROR 0x0080
+#define TX_OK 0x0100
+#define TX_LATE_COL 0x0200
+#define TX_JBR 0x0400
+#define TX_16_COL 0x8000
+#define TX_SEND_OK_BITS (TX_OK|TX_LOST_CRS)
+#define TX_COL_COUNT_MASK 0x7800
+
+/* PP_BufEvent - Buffer Event Bit definition - Read-only */
+#define SW_INTERRUPT 0x0040
+#define RX_DMA 0x0080
+#define READY_FOR_TX 0x0100
+#define TX_UNDERRUN 0x0200
+#define RX_MISS 0x0400
+#define RX_128_BYTE 0x0800
+#define TX_COL_OVRFLW 0x1000
+#define RX_MISS_OVRFLW 0x2000
+#define RX_DEST_MATCH 0x8000
+
+/* PP_LineST - Ethernet Line Status bit definition - Read-only */
+#define LINK_OK 0x0080
+#define AUI_ON 0x0100
+#define TENBASET_ON 0x0200
+#define POLARITY_OK 0x1000
+#define CRS_OK 0x4000
+
+/* PP_SelfST - Chip Software Status bit definition */
+#define ACTIVE_33V 0x0040
+#define INIT_DONE 0x0080
+#define SI_BUSY 0x0100
+#define EEPROM_PRESENT 0x0200
+#define EEPROM_OK 0x0400
+#define EL_PRESENT 0x0800
+#define EE_SIZE_64 0x1000
+
+/* PP_BusST - ISA Bus Status bit definition */
+#define TX_BID_ERROR 0x0080
+#define READY_FOR_TX_NOW 0x0100
+
+/* PP_AutoNegCTL - Auto Negotiation Control bit definition */
+#define RE_NEG_NOW 0x0040
+#define ALLOW_FDX 0x0080
+#define AUTO_NEG_ENABLE 0x0100
+#define NLP_ENABLE 0x0200
+#define FORCE_FDX 0x8000
+#define AUTO_NEG_BITS (FORCE_FDX|NLP_ENABLE|AUTO_NEG_ENABLE)
+#define AUTO_NEG_MASK (FORCE_FDX|NLP_ENABLE|AUTO_NEG_ENABLE|ALLOW_FDX|RE_NEG_NOW)
+
+/* PP_AutoNegST - Auto Negotiation Status bit definition */
+#define AUTO_NEG_BUSY 0x0080
+#define FLP_LINK 0x0100
+#define FLP_LINK_GOOD 0x0800
+#define LINK_FAULT 0x1000
+#define HDX_ACTIVE 0x4000
+#define FDX_ACTIVE 0x8000
+
+/*  The following block defines the ISQ event types */
+#define ISQ_RECEIVER_EVENT 0x04
+#define ISQ_TRANSMITTER_EVENT 0x08
+#define ISQ_BUFFER_EVENT 0x0c
+#define ISQ_RX_MISS_EVENT 0x10
+#define ISQ_TX_COL_EVENT 0x12
+
+#define ISQ_EVENT_MASK 0x003F   /*  ISQ mask to find out type of event */
+#define ISQ_HIST 16		/*  small history buffer */
+#define AUTOINCREMENT 0x8000	/*  Bit mask to set bit-15 for autoincrement */
+
+#define TXRXBUFSIZE 0x0600
+#define RXDMABUFSIZE 0x8000
+#define RXDMASIZE 0x4000
+#define TXRX_LENGTH_MASK 0x07FF
+
+/*  rx options bits */
+#define RCV_WITH_RXON	1       /*  Set SerRx ON */
+#define RCV_COUNTS	2       /*  Use Framecnt1 */
+#define RCV_PONG	4       /*  Pong respondent */
+#define RCV_DONG	8       /*  Dong operation */
+#define RCV_POLLING	0x10	/*  Poll RxEvent */
+#define RCV_ISQ		0x20	/*  Use ISQ, int */
+#define RCV_AUTO_DMA	0x100	/*  Set AutoRxDMAE */
+#define RCV_DMA		0x200	/*  Set RxDMA only */
+#define RCV_DMA_ALL	0x400	/*  Copy all DMA'ed */
+#define RCV_FIXED_DATA	0x800	/*  Every frame same */
+#define RCV_IO		0x1000	/*  Use ISA IO only */
+#define RCV_MEMORY	0x2000	/*  Use ISA Memory */
+
+#define RAM_SIZE	0x1000       /*  The card has 4k bytes or RAM */
+#define PKT_START PP_TxFrame  /*  Start of packet RAM */
+
+#define RX_FRAME_PORT	CS89x0_PORT(0x0000)
+#define TX_FRAME_PORT RX_FRAME_PORT
+#define TX_CMD_PORT	CS89x0_PORT(0x0004)
+#define TX_NOW		0x0000       /*  Tx packet after   5 bytes copied */
+#define TX_AFTER_381	0x0040       /*  Tx packet after 381 bytes copied */
+#define TX_AFTER_ALL	0x00c0       /*  Tx packet after all bytes copied */
+#define TX_LEN_PORT	CS89x0_PORT(0x0006)
+#define ISQ_PORT	CS89x0_PORT(0x0008)
+#define ADD_PORT	CS89x0_PORT(0x000A)
+#define DATA_PORT	CS89x0_PORT(0x000C)
+
+#define EEPROM_WRITE_EN		0x00F0
+#define EEPROM_WRITE_DIS	0x0000
+#define EEPROM_WRITE_CMD	0x0100
+#define EEPROM_READ_CMD		0x0200
+
+/*  Receive Header */
+/*  Description of header of each packet in receive area of memory */
+#define RBUF_EVENT_LOW	0   /*  Low byte of RxEvent - status of received frame */
+#define RBUF_EVENT_HIGH	1   /*  High byte of RxEvent - status of received frame */
+#define RBUF_LEN_LOW	2   /*  Length of received data - low byte */
+#define RBUF_LEN_HI	3   /*  Length of received data - high byte */
+#define RBUF_HEAD_LEN	4   /*  Length of this header */
+
+#define CHIP_READ 0x1   /*  Used to mark state of the repins code (chip or dma) */
+#define DMA_READ 0x2   /*  Used to mark state of the repins code (chip or dma) */
+
+/*  for bios scan */
+/*  */
+#ifdef CSDEBUG
+/*  use these values for debugging bios scan */
+#define BIOS_START_SEG 0x00000
+#define BIOS_OFFSET_INC 0x0010
+#else
+#define BIOS_START_SEG 0x0c000
+#define BIOS_OFFSET_INC 0x0200
+#endif
+
+#define BIOS_LAST_OFFSET 0x0fc00
+
+/*  Byte offsets into the EEPROM configuration buffer */
+#define ISA_CNF_OFFSET 0x6
+#define TX_CTL_OFFSET (ISA_CNF_OFFSET + 8)			/*  8900 eeprom */
+#define AUTO_NEG_CNF_OFFSET (ISA_CNF_OFFSET + 8)		/*  8920 eeprom */
+
+  /*  the assumption here is that the bits in the eeprom are generally  */
+  /*  in the same position as those in the autonegctl register. */
+  /*  Of course the IMM bit is not in that register so it must be  */
+  /*  masked out */
+#define EE_FORCE_FDX  0x8000
+#define EE_NLP_ENABLE 0x0200
+#define EE_AUTO_NEG_ENABLE 0x0100
+#define EE_ALLOW_FDX 0x0080
+#define EE_AUTO_NEG_CNF_MASK (EE_FORCE_FDX|EE_NLP_ENABLE|EE_AUTO_NEG_ENABLE|EE_ALLOW_FDX)
+
+#define IMM_BIT 0x0040		/*  ignore missing media	 */
+
+#define ADAPTER_CNF_OFFSET (AUTO_NEG_CNF_OFFSET + 2)
+#define A_CNF_10B_T 0x0001
+#define A_CNF_AUI 0x0002
+#define A_CNF_10B_2 0x0004
+#define A_CNF_MEDIA_TYPE 0x0070
+#define A_CNF_MEDIA_AUTO 0x0070
+#define A_CNF_MEDIA_10B_T 0x0020
+#define A_CNF_MEDIA_AUI 0x0040
+#define A_CNF_MEDIA_10B_2 0x0010
+#define A_CNF_DC_DC_POLARITY 0x0080
+#define A_CNF_NO_AUTO_POLARITY 0x2000
+#define A_CNF_LOW_RX_SQUELCH 0x4000
+#define A_CNF_EXTND_10B_2 0x8000
+
+#define PACKET_PAGE_OFFSET 0x8
+
+/*  Bit definitions for the ISA configuration word from the EEPROM */
+#define INT_NO_MASK 0x000F
+#define DMA_NO_MASK 0x0070
+#define ISA_DMA_SIZE 0x0200
+#define ISA_AUTO_RxDMA 0x0400
+#define ISA_RxDMA 0x0800
+#define DMA_BURST 0x1000
+#define STREAM_TRANSFER 0x2000
+#define ANY_ISA_DMA (ISA_AUTO_RxDMA | ISA_RxDMA)
+
+/*  DMA controller registers */
+#define DMA_BASE 0x00     /*  DMA controller base */
+#define DMA_BASE_2 0x0C0    /*  DMA controller base */
+
+#define DMA_STAT 0x0D0    /*  DMA controller status register */
+#define DMA_MASK 0x0D4    /*  DMA controller mask register */
+#define DMA_MODE 0x0D6    /*  DMA controller mode register */
+#define DMA_RESETFF 0x0D8    /*  DMA controller first/last flip flop */
+
+/*  DMA data */
+#define DMA_DISABLE 0x04     /*  Disable channel n */
+#define DMA_ENABLE 0x00     /*  Enable channel n */
+/*  Demand transfers, incr. address, auto init, writes, ch. n */
+#define DMA_RX_MODE 0x14
+/*  Demand transfers, incr. address, auto init, reads, ch. n */
+#define DMA_TX_MODE 0x18
+
+#define DMA_SIZE (16*1024) /*  Size of dma buffer - 16k */
+
+#define CS8900 0x0000
+#define CS8920 0x4000   
+#define CS8920M 0x6000   
+#define REVISON_BITS 0x1F00
+#define EEVER_NUMBER 0x12
+#define CHKSUM_LEN 0x14
+#define CHKSUM_VAL 0x0000
+#define START_EEPROM_DATA 0x001c /*  Offset into eeprom for start of data */
+#define IRQ_MAP_EEPROM_DATA 0x0046 /*  Offset into eeprom for the IRQ map */
+#define IRQ_MAP_LEN 0x0004 /*  No of bytes to read for the IRQ map */
+#define PNP_IRQ_FRMT 0x0022 /*  PNP small item IRQ format */
+#ifdef CONFIG_SH_HICOSH4
+#define CS8900_IRQ_MAP 0x0002 /* HiCO-SH4 board has its IRQ on #1 */
+#else
+#define CS8900_IRQ_MAP 0x1c20 /*  This IRQ map is fixed */
+#endif
+
+#define CS8920_NO_INTS 0x0F   /*  Max CS8920 interrupt select # */
+
+#define PNP_ADD_PORT 0x0279
+#define PNP_WRITE_PORT 0x0A79
+
+#define GET_PNP_ISA_STRUCT 0x40
+#define PNP_ISA_STRUCT_LEN 0x06
+#define PNP_CSN_CNT_OFF 0x01
+#define PNP_RD_PORT_OFF 0x02
+#define PNP_FUNCTION_OK 0x00
+#define PNP_WAKE 0x03
+#define PNP_RSRC_DATA 0x04
+#define PNP_RSRC_READY 0x01
+#define PNP_STATUS 0x05
+#define PNP_ACTIVATE 0x30
+#define PNP_CNF_IO_H 0x60
+#define PNP_CNF_IO_L 0x61
+#define PNP_CNF_INT 0x70
+#define PNP_CNF_DMA 0x74
+#define PNP_CNF_MEM 0x48
+
+#define BIT0 1
+#define BIT15 0x8000
+