diff --git a/drivers/net/ewrk3.c b/drivers/net/ewrk3.c
new file mode 100644
index 0000000..dcf969b
--- /dev/null
+++ b/drivers/net/ewrk3.c
@@ -0,0 +1,2007 @@
+/*  ewrk3.c: A DIGITAL EtherWORKS 3 ethernet driver for Linux.
+
+   Written 1994 by David C. Davies.
+
+   Copyright 1994 Digital Equipment Corporation.
+
+   This software may be used and distributed according to the terms of
+   the GNU General Public License, incorporated herein by reference.
+
+   This driver is written for the Digital Equipment Corporation series
+   of EtherWORKS ethernet cards:
+
+   DE203 Turbo (BNC)
+   DE204 Turbo (TP)
+   DE205 Turbo (TP BNC)
+
+   The driver has been tested on a relatively busy  network using the DE205
+   card and benchmarked with 'ttcp': it transferred 16M  of data at 975kB/s
+   (7.8Mb/s) to a DECstation 5000/200.
+
+   The author may be reached at davies@maniac.ultranet.com.
+
+   =========================================================================
+   This driver has been written  substantially  from scratch, although  its
+   inheritance of style and stack interface from 'depca.c' and in turn from
+   Donald Becker's 'lance.c' should be obvious.
+
+   The  DE203/4/5 boards  all  use a new proprietary   chip in place of the
+   LANCE chip used in prior cards  (DEPCA, DE100, DE200/1/2, DE210, DE422).
+   Use the depca.c driver in the standard distribution  for the LANCE based
+   cards from DIGITAL; this driver will not work with them.
+
+   The DE203/4/5 cards have 2  main modes: shared memory  and I/O only. I/O
+   only makes  all the card accesses through  I/O transactions and  no high
+   (shared)  memory is used. This  mode provides a >48% performance penalty
+   and  is deprecated in this  driver,  although allowed to provide initial
+   setup when hardstrapped.
+
+   The shared memory mode comes in 3 flavours: 2kB, 32kB and 64kB. There is
+   no point in using any mode other than the 2kB  mode - their performances
+   are virtually identical, although the driver has  been tested in the 2kB
+   and 32kB modes. I would suggest you uncomment the line:
+
+   FORCE_2K_MODE;
+
+   to allow the driver to configure the card as a  2kB card at your current
+   base  address, thus leaving more  room to clutter  your  system box with
+   other memory hungry boards.
+
+   As many ISA  and EISA cards  can be supported  under this driver  as you
+   wish, limited primarily  by the available IRQ lines,  rather than by the
+   available I/O addresses  (24 ISA,  16 EISA).   I have  checked different
+   configurations of  multiple  depca cards and  ewrk3 cards  and have  not
+   found a problem yet (provided you have at least depca.c v0.38) ...
+
+   The board IRQ setting   must be at  an unused  IRQ which is  auto-probed
+   using  Donald  Becker's autoprobe  routines.   All  these cards   are at
+   {5,10,11,15}.
+
+   No 16MB memory  limitation should exist with this  driver as DMA is  not
+   used and the common memory area is in low memory on the network card (my
+   current system has 20MB and I've not had problems yet).
+
+   The ability to load  this driver as a  loadable module has been included
+   and used  extensively during the  driver development (to save those long
+   reboot sequences). To utilise this ability, you have to do 8 things:
+
+   0) have a copy of the loadable modules code installed on your system.
+   1) copy ewrk3.c from the  /linux/drivers/net directory to your favourite
+   temporary directory.
+   2) edit the  source code near  line 1898 to reflect  the I/O address and
+   IRQ you're using.
+   3) compile  ewrk3.c, but include -DMODULE in  the command line to ensure
+   that the correct bits are compiled (see end of source code).
+   4) if you are wanting to add a new  card, goto 5. Otherwise, recompile a
+   kernel with the ewrk3 configuration turned off and reboot.
+   5) insmod ewrk3.o
+   [Alan Cox: Changed this so you can insmod ewrk3.o irq=x io=y]
+   [Adam Kropelin: now accepts irq=x1,x2 io=y1,y2 for multiple cards]
+   6) run the net startup bits for your new eth?? interface manually
+   (usually /etc/rc.inet[12] at boot time).
+   7) enjoy!
+
+   Note that autoprobing is not allowed in loadable modules - the system is
+   already up and running and you're messing with interrupts.
+
+   To unload a module, turn off the associated interface
+   'ifconfig eth?? down' then 'rmmod ewrk3'.
+
+   Promiscuous   mode has been  turned  off  in this driver,   but  all the
+   multicast  address bits  have been   turned on. This  improved the  send
+   performance on a busy network by about 13%.
+
+   Ioctl's have now been provided (primarily because  I wanted to grab some
+   packet size statistics). They  are patterned after 'plipconfig.c' from a
+   suggestion by Alan Cox.  Using these  ioctls, you can enable promiscuous
+   mode, add/delete multicast  addresses, change the hardware address,  get
+   packet size distribution statistics and muck around with the control and
+   status register. I'll add others if and when the need arises.
+
+   TO DO:
+   ------
+
+
+   Revision History
+   ----------------
+
+   Version   Date        Description
+
+   0.1     26-aug-94   Initial writing. ALPHA code release.
+   0.11    31-aug-94   Fixed: 2k mode memory base calc.,
+   LeMAC version calc.,
+   IRQ vector assignments during autoprobe.
+   0.12    31-aug-94   Tested working on LeMAC2 (DE20[345]-AC) card.
+   Fixed up MCA hash table algorithm.
+   0.20     4-sep-94   Added IOCTL functionality.
+   0.21    14-sep-94   Added I/O mode.
+   0.21axp 15-sep-94   Special version for ALPHA AXP Linux V1.0.
+   0.22    16-sep-94   Added more IOCTLs & tidied up.
+   0.23    21-sep-94   Added transmit cut through.
+   0.24    31-oct-94   Added uid checks in some ioctls.
+   0.30     1-nov-94   BETA code release.
+   0.31     5-dec-94   Added check/allocate region code.
+   0.32    16-jan-95   Broadcast packet fix.
+   0.33    10-Feb-95   Fix recognition bug reported by <bkm@star.rl.ac.uk>.
+   0.40    27-Dec-95   Rationalise MODULE and autoprobe code.
+   Rewrite for portability & updated.
+   ALPHA support from <jestabro@amt.tay1.dec.com>
+   Added verify_area() calls in ewrk3_ioctl() from
+   suggestion by <heiko@colossus.escape.de>.
+   Add new multicasting code.
+   0.41    20-Jan-96   Fix IRQ set up problem reported by
+   <kenneth@bbs.sas.ntu.ac.sg>.
+   0.42    22-Apr-96   Fix alloc_device() bug <jari@markkus2.fimr.fi>
+   0.43    16-Aug-96   Update alloc_device() to conform to de4x5.c
+   0.44    08-Nov-01   use library crc32 functions <Matt_Domsch@dell.com>
+   0.45    19-Jul-02   fix unaligned access on alpha <martin@bruli.net>
+   0.46    10-Oct-02   Multiple NIC support when module <akropel1@rochester.rr.com>
+   0.47    18-Oct-02   ethtool support <akropel1@rochester.rr.com>
+   0.48    18-Oct-02   cli/sti removal for 2.5 <vda@port.imtp.ilyichevsk.odessa.ua>
+   ioctl locking, signature search cleanup <akropel1@rochester.rr.com>
+
+   =========================================================================
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/crc32.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/ethtool.h>
+#include <linux/time.h>
+#include <linux/types.h>
+#include <linux/unistd.h>
+#include <linux/ctype.h>
+#include <linux/bitops.h>
+
+#include <asm/io.h>
+#include <asm/dma.h>
+#include <asm/uaccess.h>
+
+#include "ewrk3.h"
+
+#define DRV_NAME	"ewrk3"
+#define DRV_VERSION	"0.48"
+
+static char version[] __initdata =
+DRV_NAME ":v" DRV_VERSION " 2002/10/18 davies@maniac.ultranet.com\n";
+
+#ifdef EWRK3_DEBUG
+static int ewrk3_debug = EWRK3_DEBUG;
+#else
+static int ewrk3_debug = 1;
+#endif
+
+#define EWRK3_NDA 0xffe0	/* No Device Address */
+
+#define PROBE_LENGTH    32
+#define ETH_PROM_SIG    0xAA5500FFUL
+
+#ifndef EWRK3_SIGNATURE
+#define EWRK3_SIGNATURE {"DE203","DE204","DE205",""}
+#define EWRK3_STRLEN 8
+#endif
+
+#ifndef EWRK3_RAM_BASE_ADDRESSES
+#define EWRK3_RAM_BASE_ADDRESSES {0xc0000,0xd0000,0x00000}
+#endif
+
+/*
+   ** Sets up the I/O area for the autoprobe.
+ */
+#define EWRK3_IO_BASE 0x100	/* Start address for probe search */
+#define EWRK3_IOP_INC 0x20	/* I/O address increment */
+#define EWRK3_TOTAL_SIZE 0x20	/* required I/O address length */
+
+#ifndef MAX_NUM_EWRK3S
+#define MAX_NUM_EWRK3S 21
+#endif
+
+#ifndef EWRK3_EISA_IO_PORTS
+#define EWRK3_EISA_IO_PORTS 0x0c00	/* I/O port base address, slot 0 */
+#endif
+
+#ifndef MAX_EISA_SLOTS
+#define MAX_EISA_SLOTS 16
+#define EISA_SLOT_INC 0x1000
+#endif
+
+#define QUEUE_PKT_TIMEOUT (1*HZ)	/* Jiffies */
+
+/*
+   ** EtherWORKS 3 shared memory window sizes
+ */
+#define IO_ONLY         0x00
+#define SHMEM_2K        0x800
+#define SHMEM_32K       0x8000
+#define SHMEM_64K       0x10000
+
+/*
+   ** EtherWORKS 3 IRQ ENABLE/DISABLE
+ */
+#define ENABLE_IRQs { \
+  icr |= lp->irq_mask;\
+  outb(icr, EWRK3_ICR);                     /* Enable the IRQs */\
+}
+
+#define DISABLE_IRQs { \
+  icr = inb(EWRK3_ICR);\
+  icr &= ~lp->irq_mask;\
+  outb(icr, EWRK3_ICR);                     /* Disable the IRQs */\
+}
+
+/*
+   ** EtherWORKS 3 START/STOP
+ */
+#define START_EWRK3 { \
+  csr = inb(EWRK3_CSR);\
+  csr &= ~(CSR_TXD|CSR_RXD);\
+  outb(csr, EWRK3_CSR);                     /* Enable the TX and/or RX */\
+}
+
+#define STOP_EWRK3 { \
+  csr = (CSR_TXD|CSR_RXD);\
+  outb(csr, EWRK3_CSR);                     /* Disable the TX and/or RX */\
+}
+
+/*
+   ** The EtherWORKS 3 private structure
+ */
+#define EWRK3_PKT_STAT_SZ 16
+#define EWRK3_PKT_BIN_SZ  128	/* Should be >=100 unless you
+				   increase EWRK3_PKT_STAT_SZ */
+
+struct ewrk3_stats {
+	u32 bins[EWRK3_PKT_STAT_SZ];
+	u32 unicast;
+	u32 multicast;
+	u32 broadcast;
+	u32 excessive_collisions;
+	u32 tx_underruns;
+	u32 excessive_underruns;
+};
+
+struct ewrk3_private {
+	char adapter_name[80];	/* Name exported to /proc/ioports */
+	u_long shmem_base;	/* Shared memory start address */
+	void __iomem *shmem;
+	u_long shmem_length;	/* Shared memory window length */
+	struct net_device_stats stats;	/* Public stats */
+	struct ewrk3_stats pktStats; /* Private stats counters */
+	u_char irq_mask;	/* Adapter IRQ mask bits */
+	u_char mPage;		/* Maximum 2kB Page number */
+	u_char lemac;		/* Chip rev. level */
+	u_char hard_strapped;	/* Don't allow a full open */
+	u_char txc;		/* Transmit cut through */
+	void __iomem *mctbl;	/* Pointer to the multicast table */
+	u_char led_mask;	/* Used to reserve LED access for ethtool */
+	spinlock_t hw_lock;
+};
+
+/*
+   ** Force the EtherWORKS 3 card to be in 2kB MODE
+ */
+#define FORCE_2K_MODE { \
+  shmem_length = SHMEM_2K;\
+  outb(((mem_start - 0x80000) >> 11), EWRK3_MBR);\
+}
+
+/*
+   ** Public Functions
+ */
+static int ewrk3_open(struct net_device *dev);
+static int ewrk3_queue_pkt(struct sk_buff *skb, struct net_device *dev);
+static irqreturn_t ewrk3_interrupt(int irq, void *dev_id, struct pt_regs *regs);
+static int ewrk3_close(struct net_device *dev);
+static struct net_device_stats *ewrk3_get_stats(struct net_device *dev);
+static void set_multicast_list(struct net_device *dev);
+static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
+static struct ethtool_ops ethtool_ops_203;
+static struct ethtool_ops ethtool_ops;
+
+/*
+   ** Private functions
+ */
+static int ewrk3_hw_init(struct net_device *dev, u_long iobase);
+static void ewrk3_init(struct net_device *dev);
+static int ewrk3_rx(struct net_device *dev);
+static int ewrk3_tx(struct net_device *dev);
+static void ewrk3_timeout(struct net_device *dev);
+
+static void EthwrkSignature(char *name, char *eeprom_image);
+static int DevicePresent(u_long iobase);
+static void SetMulticastFilter(struct net_device *dev);
+static int EISA_signature(char *name, s32 eisa_id);
+
+static int Read_EEPROM(u_long iobase, u_char eaddr);
+static int Write_EEPROM(short data, u_long iobase, u_char eaddr);
+static u_char get_hw_addr(struct net_device *dev, u_char * eeprom_image, char chipType);
+
+static int ewrk3_probe1(struct net_device *dev, u_long iobase, int irq);
+static int isa_probe(struct net_device *dev, u_long iobase);
+static int eisa_probe(struct net_device *dev, u_long iobase);
+
+static u_char irq[MAX_NUM_EWRK3S+1] = {5, 0, 10, 3, 11, 9, 15, 12};
+
+static char name[EWRK3_STRLEN + 1];
+static int num_ewrks3s;
+
+/*
+   ** Miscellaneous defines...
+ */
+#define INIT_EWRK3 {\
+    outb(EEPROM_INIT, EWRK3_IOPR);\
+    mdelay(1);\
+}
+
+#ifndef MODULE
+struct net_device * __init ewrk3_probe(int unit)
+{
+	struct net_device *dev = alloc_etherdev(sizeof(struct ewrk3_private));
+	int err;
+
+	if (!dev)
+		return ERR_PTR(-ENOMEM);
+
+	if (unit >= 0) {
+		sprintf(dev->name, "eth%d", unit);
+		netdev_boot_setup_check(dev);
+	}
+	SET_MODULE_OWNER(dev);
+
+	err = ewrk3_probe1(dev, dev->base_addr, dev->irq);
+	if (err) 
+		goto out;
+	return dev;
+out:
+	free_netdev(dev);
+	return ERR_PTR(err);
+	
+}
+#endif
+
+static int __init ewrk3_probe1(struct net_device *dev, u_long iobase, int irq)
+{
+	int err;
+
+	dev->base_addr = iobase;
+	dev->irq = irq;
+
+	/* Address PROM pattern */
+	err = isa_probe(dev, iobase);
+	if (err != 0) 
+		err = eisa_probe(dev, iobase);
+
+	if (err)
+		return err;
+
+	err = register_netdev(dev);
+	if (err)
+		release_region(dev->base_addr, EWRK3_TOTAL_SIZE);
+
+	return err;
+}
+
+static int __init 
+ewrk3_hw_init(struct net_device *dev, u_long iobase)
+{
+	struct ewrk3_private *lp;
+	int i, status = 0;
+	u_long mem_start, shmem_length;
+	u_char cr, cmr, icr, nicsr, lemac, hard_strapped = 0;
+	u_char eeprom_image[EEPROM_MAX], chksum, eisa_cr = 0;
+
+	/*
+	** Stop the EWRK3. Enable the DBR ROM. Disable interrupts and remote boot.
+	** This also disables the EISA_ENABLE bit in the EISA Control Register.
+	 */
+	if (iobase > 0x400)
+		eisa_cr = inb(EISA_CR);
+	INIT_EWRK3;
+
+	nicsr = inb(EWRK3_CSR);
+
+	icr = inb(EWRK3_ICR);
+	icr &= 0x70;
+	outb(icr, EWRK3_ICR);	/* Disable all the IRQs */
+
+	if (nicsr == (CSR_TXD | CSR_RXD))
+		return -ENXIO;
+
+
+	/* Check that the EEPROM is alive and well and not living on Pluto... */
+	for (chksum = 0, i = 0; i < EEPROM_MAX; i += 2) {
+		union {
+			short val;
+			char c[2];
+		} tmp;
+
+		tmp.val = (short) Read_EEPROM(iobase, (i >> 1));
+		eeprom_image[i] = tmp.c[0];
+		eeprom_image[i + 1] = tmp.c[1];
+		chksum += eeprom_image[i] + eeprom_image[i + 1];
+	}
+
+	if (chksum != 0) {	/* Bad EEPROM Data! */
+		printk("%s: Device has a bad on-board EEPROM.\n", dev->name);
+		return -ENXIO;
+	}
+	
+	EthwrkSignature(name, eeprom_image);
+	if (*name == '\0') 
+		return -ENXIO;
+
+	dev->base_addr = iobase;
+				
+	if (iobase > 0x400) {
+		outb(eisa_cr, EISA_CR);		/* Rewrite the EISA CR */
+	}
+	lemac = eeprom_image[EEPROM_CHIPVER];
+	cmr = inb(EWRK3_CMR);
+	
+	if (((lemac == LeMAC) && ((cmr & CMR_NO_EEPROM) != CMR_NO_EEPROM)) ||
+	    ((lemac == LeMAC2) && !(cmr & CMR_HS))) {
+		printk("%s: %s at %#4lx", dev->name, name, iobase);
+		hard_strapped = 1;
+	} else if ((iobase & 0x0fff) == EWRK3_EISA_IO_PORTS) {
+		/* EISA slot address */
+		printk("%s: %s at %#4lx (EISA slot %ld)",
+		       dev->name, name, iobase, ((iobase >> 12) & 0x0f));
+	} else {	/* ISA port address */
+		printk("%s: %s at %#4lx", dev->name, name, iobase);
+	}
+
+	printk(", h/w address ");
+	if (lemac != LeMAC2)
+		DevicePresent(iobase);	/* need after EWRK3_INIT */
+	status = get_hw_addr(dev, eeprom_image, lemac);
+	for (i = 0; i < ETH_ALEN - 1; i++) {	/* get the ethernet addr. */
+		printk("%2.2x:", dev->dev_addr[i]);
+	}
+	printk("%2.2x,\n", dev->dev_addr[i]);
+	
+	if (status) {
+		printk("      which has an EEPROM CRC error.\n");
+		return -ENXIO;
+	}
+
+	if (lemac == LeMAC2) {	/* Special LeMAC2 CMR things */
+		cmr &= ~(CMR_RA | CMR_WB | CMR_LINK | CMR_POLARITY | CMR_0WS);
+		if (eeprom_image[EEPROM_MISC0] & READ_AHEAD)
+			cmr |= CMR_RA;
+		if (eeprom_image[EEPROM_MISC0] & WRITE_BEHIND)
+			cmr |= CMR_WB;
+		if (eeprom_image[EEPROM_NETMAN0] & NETMAN_POL)
+			cmr |= CMR_POLARITY;
+		if (eeprom_image[EEPROM_NETMAN0] & NETMAN_LINK)
+			cmr |= CMR_LINK;
+		if (eeprom_image[EEPROM_MISC0] & _0WS_ENA)
+			cmr |= CMR_0WS;
+	}
+	if (eeprom_image[EEPROM_SETUP] & SETUP_DRAM)
+		cmr |= CMR_DRAM;
+	outb(cmr, EWRK3_CMR);
+	
+	cr = inb(EWRK3_CR);	/* Set up the Control Register */
+	cr |= eeprom_image[EEPROM_SETUP] & SETUP_APD;
+	if (cr & SETUP_APD)
+		cr |= eeprom_image[EEPROM_SETUP] & SETUP_PS;
+	cr |= eeprom_image[EEPROM_MISC0] & FAST_BUS;
+	cr |= eeprom_image[EEPROM_MISC0] & ENA_16;
+	outb(cr, EWRK3_CR);
+
+	/*
+	** Determine the base address and window length for the EWRK3
+	** RAM from the memory base register.
+	*/
+	mem_start = inb(EWRK3_MBR);
+	shmem_length = 0;
+	if (mem_start != 0) {
+		if ((mem_start >= 0x0a) && (mem_start <= 0x0f)) {
+			mem_start *= SHMEM_64K;
+			shmem_length = SHMEM_64K;
+		} else if ((mem_start >= 0x14) && (mem_start <= 0x1f)) {
+			mem_start *= SHMEM_32K;
+			shmem_length = SHMEM_32K;
+		} else if ((mem_start >= 0x40) && (mem_start <= 0xff)) {
+			mem_start = mem_start * SHMEM_2K + 0x80000;
+			shmem_length = SHMEM_2K;
+		} else {
+			return -ENXIO;
+		}
+	}
+	/*
+	** See the top of this source code for comments about
+	** uncommenting this line.
+	*/
+/*          FORCE_2K_MODE; */
+	
+	if (hard_strapped) {
+		printk("      is hard strapped.\n");
+	} else if (mem_start) {
+		printk("      has a %dk RAM window", (int) (shmem_length >> 10));
+		printk(" at 0x%.5lx", mem_start);
+	} else {
+		printk("      is in I/O only mode");
+	}
+
+	lp = netdev_priv(dev);
+	lp->shmem_base = mem_start;
+	lp->shmem = ioremap(mem_start, shmem_length);
+	if (!lp->shmem)
+		return -ENOMEM;
+	lp->shmem_length = shmem_length;
+	lp->lemac = lemac;
+	lp->hard_strapped = hard_strapped;
+	lp->led_mask = CR_LED;
+	spin_lock_init(&lp->hw_lock);
+	
+	lp->mPage = 64;
+	if (cmr & CMR_DRAM)
+		lp->mPage <<= 1;	/* 2 DRAMS on module */
+	
+	sprintf(lp->adapter_name, "%s (%s)", name, dev->name);
+	
+	lp->irq_mask = ICR_TNEM | ICR_TXDM | ICR_RNEM | ICR_RXDM;
+	
+	if (!hard_strapped) {
+		/*
+		** Enable EWRK3 board interrupts for autoprobing
+		*/
+		icr |= ICR_IE;	/* Enable interrupts */
+		outb(icr, EWRK3_ICR);
+		
+		/* The DMA channel may be passed in on this parameter. */
+		dev->dma = 0;
+		
+		/* To auto-IRQ we enable the initialization-done and DMA err,
+		   interrupts. For now we will always get a DMA error. */
+		if (dev->irq < 2) {
+#ifndef MODULE
+			u_char irqnum;
+			unsigned long irq_mask;
+			
+
+			irq_mask = probe_irq_on();
+			
+			/*
+			** Trigger a TNE interrupt.
+			*/
+			icr |= ICR_TNEM;
+			outb(1, EWRK3_TDQ);	/* Write to the TX done queue */
+			outb(icr, EWRK3_ICR);	/* Unmask the TXD interrupt */
+			
+			irqnum = irq[((icr & IRQ_SEL) >> 4)];
+			
+			mdelay(20);
+			dev->irq = probe_irq_off(irq_mask);
+			if ((dev->irq) && (irqnum == dev->irq)) {
+				printk(" and uses IRQ%d.\n", dev->irq);
+			} else {
+				if (!dev->irq) {
+					printk(" and failed to detect IRQ line.\n");
+				} else if ((irqnum == 1) && (lemac == LeMAC2)) {
+					printk(" and an illegal IRQ line detected.\n");
+				} else {
+					printk(", but incorrect IRQ line detected.\n");
+				}
+				iounmap(lp->shmem);
+				return -ENXIO;
+			}
+
+			DISABLE_IRQs;	/* Mask all interrupts */
+
+#endif				/* MODULE */
+		} else {
+			printk(" and requires IRQ%d.\n", dev->irq);
+		}
+	}
+
+	if (ewrk3_debug > 1) {
+		printk(version);
+	}
+	/* The EWRK3-specific entries in the device structure. */
+	dev->open = ewrk3_open;
+	dev->hard_start_xmit = ewrk3_queue_pkt;
+	dev->stop = ewrk3_close;
+	dev->get_stats = ewrk3_get_stats;
+	dev->set_multicast_list = set_multicast_list;
+	dev->do_ioctl = ewrk3_ioctl;
+	if (lp->adapter_name[4] == '3')
+		SET_ETHTOOL_OPS(dev, &ethtool_ops_203);
+	else
+		SET_ETHTOOL_OPS(dev, &ethtool_ops);
+	dev->tx_timeout = ewrk3_timeout;
+	dev->watchdog_timeo = QUEUE_PKT_TIMEOUT;
+	
+	dev->mem_start = 0;
+
+	return 0;
+}
+
+
+static int ewrk3_open(struct net_device *dev)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	u_long iobase = dev->base_addr;
+	int i, status = 0;
+	u_char icr, csr;
+
+	/*
+	   ** Stop the TX and RX...
+	 */
+	STOP_EWRK3;
+
+	if (!lp->hard_strapped) {
+		if (request_irq(dev->irq, (void *) ewrk3_interrupt, 0, "ewrk3", dev)) {
+			printk("ewrk3_open(): Requested IRQ%d is busy\n", dev->irq);
+			status = -EAGAIN;
+		} else {
+
+			/*
+			   ** Re-initialize the EWRK3...
+			 */
+			ewrk3_init(dev);
+
+			if (ewrk3_debug > 1) {
+				printk("%s: ewrk3 open with irq %d\n", dev->name, dev->irq);
+				printk("  physical address: ");
+				for (i = 0; i < 5; i++) {
+					printk("%2.2x:", (u_char) dev->dev_addr[i]);
+				}
+				printk("%2.2x\n", (u_char) dev->dev_addr[i]);
+				if (lp->shmem_length == 0) {
+					printk("  no shared memory, I/O only mode\n");
+				} else {
+					printk("  start of shared memory: 0x%08lx\n", lp->shmem_base);
+					printk("  window length: 0x%04lx\n", lp->shmem_length);
+				}
+				printk("  # of DRAMS: %d\n", ((inb(EWRK3_CMR) & 0x02) ? 2 : 1));
+				printk("  csr:  0x%02x\n", inb(EWRK3_CSR));
+				printk("  cr:   0x%02x\n", inb(EWRK3_CR));
+				printk("  icr:  0x%02x\n", inb(EWRK3_ICR));
+				printk("  cmr:  0x%02x\n", inb(EWRK3_CMR));
+				printk("  fmqc: 0x%02x\n", inb(EWRK3_FMQC));
+			}
+			netif_start_queue(dev);
+			/*
+			   ** Unmask EWRK3 board interrupts
+			 */
+			icr = inb(EWRK3_ICR);
+			ENABLE_IRQs;
+
+		}
+	} else {
+		printk(KERN_ERR "%s: ewrk3 available for hard strapped set up only.\n", dev->name);
+		printk(KERN_ERR "      Run the 'ewrk3setup' utility or remove the hard straps.\n");
+		return -EINVAL;
+	}
+
+	return status;
+}
+
+/*
+   ** Initialize the EtherWORKS 3 operating conditions
+ */
+static void ewrk3_init(struct net_device *dev)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	u_char csr, page;
+	u_long iobase = dev->base_addr;
+	int i;
+
+	/*
+	   ** Enable any multicasts
+	 */
+	set_multicast_list(dev);
+
+	/*
+	** Set hardware MAC address. Address is initialized from the EEPROM
+	** during startup but may have since been changed by the user.
+	*/
+	for (i=0; i<ETH_ALEN; i++)
+		outb(dev->dev_addr[i], EWRK3_PAR0 + i);
+
+	/*
+	   ** Clean out any remaining entries in all the queues here
+	 */
+	while (inb(EWRK3_TQ));
+	while (inb(EWRK3_TDQ));
+	while (inb(EWRK3_RQ));
+	while (inb(EWRK3_FMQ));
+
+	/*
+	   ** Write a clean free memory queue
+	 */
+	for (page = 1; page < lp->mPage; page++) {	/* Write the free page numbers */
+		outb(page, EWRK3_FMQ);	/* to the Free Memory Queue */
+	}
+
+	START_EWRK3;		/* Enable the TX and/or RX */
+}
+
+/*
+ *  Transmit timeout
+ */
+ 
+static void ewrk3_timeout(struct net_device *dev)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	u_char icr, csr;
+	u_long iobase = dev->base_addr;
+	
+	if (!lp->hard_strapped) 
+	{
+		printk(KERN_WARNING"%s: transmit timed/locked out, status %04x, resetting.\n",
+		       dev->name, inb(EWRK3_CSR));
+
+		/*
+		   ** Mask all board interrupts
+		 */
+		DISABLE_IRQs;
+
+		/*
+		   ** Stop the TX and RX...
+		 */
+		STOP_EWRK3;
+
+		ewrk3_init(dev);
+
+		/*
+		   ** Unmask EWRK3 board interrupts
+		 */
+		ENABLE_IRQs;
+
+		dev->trans_start = jiffies;
+		netif_wake_queue(dev);
+	}
+}
+
+/*
+   ** Writes a socket buffer to the free page queue
+ */
+static int ewrk3_queue_pkt (struct sk_buff *skb, struct net_device *dev)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	u_long iobase = dev->base_addr;
+	void __iomem *buf = NULL;
+	u_char icr;
+	u_char page;
+
+	spin_lock_irq (&lp->hw_lock);
+	DISABLE_IRQs;
+
+	/* if no resources available, exit, request packet be queued */
+	if (inb (EWRK3_FMQC) == 0) {
+		printk (KERN_WARNING "%s: ewrk3_queue_pkt(): No free resources...\n",
+			dev->name);
+		printk (KERN_WARNING "%s: ewrk3_queue_pkt(): CSR: %02x ICR: %02x FMQC: %02x\n",
+			dev->name, inb (EWRK3_CSR), inb (EWRK3_ICR),
+			inb (EWRK3_FMQC));
+		goto err_out;
+	}
+
+	/*
+	 ** Get a free page from the FMQ
+	 */
+	if ((page = inb (EWRK3_FMQ)) >= lp->mPage) {
+		printk ("ewrk3_queue_pkt(): Invalid free memory page (%d).\n",
+		     (u_char) page);
+		goto err_out;
+	}
+
+
+	/*
+	 ** Set up shared memory window and pointer into the window
+	 */
+	if (lp->shmem_length == IO_ONLY) {
+		outb (page, EWRK3_IOPR);
+	} else if (lp->shmem_length == SHMEM_2K) {
+		buf = lp->shmem;
+		outb (page, EWRK3_MPR);
+	} else if (lp->shmem_length == SHMEM_32K) {
+		buf = (((short) page << 11) & 0x7800) + lp->shmem;
+		outb ((page >> 4), EWRK3_MPR);
+	} else if (lp->shmem_length == SHMEM_64K) {
+		buf = (((short) page << 11) & 0xf800) + lp->shmem;
+		outb ((page >> 5), EWRK3_MPR);
+	} else {
+		printk (KERN_ERR "%s: Oops - your private data area is hosed!\n",
+			dev->name);
+		BUG ();
+	}
+
+	/*
+	 ** Set up the buffer control structures and copy the data from
+	 ** the socket buffer to the shared memory .
+	 */
+	if (lp->shmem_length == IO_ONLY) {
+		int i;
+		u_char *p = skb->data;
+		outb ((char) (TCR_QMODE | TCR_PAD | TCR_IFC), EWRK3_DATA);
+		outb ((char) (skb->len & 0xff), EWRK3_DATA);
+		outb ((char) ((skb->len >> 8) & 0xff), EWRK3_DATA);
+		outb ((char) 0x04, EWRK3_DATA);
+		for (i = 0; i < skb->len; i++) {
+			outb (*p++, EWRK3_DATA);
+		}
+		outb (page, EWRK3_TQ);	/* Start sending pkt */
+	} else {
+		writeb ((char) (TCR_QMODE | TCR_PAD | TCR_IFC), buf);	/* ctrl byte */
+		buf += 1;
+		writeb ((char) (skb->len & 0xff), buf);	/* length (16 bit xfer) */
+		buf += 1;
+		if (lp->txc) {
+			writeb(((skb->len >> 8) & 0xff) | XCT, buf);
+			buf += 1;
+			writeb (0x04, buf);	/* index byte */
+			buf += 1;
+			writeb (0x00, (buf + skb->len));	/* Write the XCT flag */
+			memcpy_toio (buf, skb->data, PRELOAD);	/* Write PRELOAD bytes */
+			outb (page, EWRK3_TQ);	/* Start sending pkt */
+			memcpy_toio (buf + PRELOAD,
+					 skb->data + PRELOAD,
+					 skb->len - PRELOAD);
+			writeb (0xff, (buf + skb->len));	/* Write the XCT flag */
+		} else {
+			writeb ((skb->len >> 8) & 0xff, buf);
+			buf += 1;
+			writeb (0x04, buf);	/* index byte */
+			buf += 1;
+			memcpy_toio (buf, skb->data, skb->len);	/* Write data bytes */
+			outb (page, EWRK3_TQ);	/* Start sending pkt */
+		}
+	}
+
+	ENABLE_IRQs;
+	spin_unlock_irq (&lp->hw_lock);
+
+	lp->stats.tx_bytes += skb->len;
+	dev->trans_start = jiffies;
+	dev_kfree_skb (skb);
+
+	/* Check for free resources: stop Tx queue if there are none */
+	if (inb (EWRK3_FMQC) == 0)
+		netif_stop_queue (dev);
+
+	return 0;
+
+err_out:
+	ENABLE_IRQs;
+	spin_unlock_irq (&lp->hw_lock);
+	return 1;
+}
+
+/*
+   ** The EWRK3 interrupt handler.
+ */
+static irqreturn_t ewrk3_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+	struct net_device *dev = dev_id;
+	struct ewrk3_private *lp;
+	u_long iobase;
+	u_char icr, cr, csr;
+
+	lp = netdev_priv(dev);
+	iobase = dev->base_addr;
+
+	/* get the interrupt information */
+	csr = inb(EWRK3_CSR);
+
+	/*
+	 ** Mask the EWRK3 board interrupts and turn on the LED
+	 */
+	spin_lock(&lp->hw_lock);
+	DISABLE_IRQs;
+
+	cr = inb(EWRK3_CR);
+	cr |= lp->led_mask;
+	outb(cr, EWRK3_CR);
+
+	if (csr & CSR_RNE)	/* Rx interrupt (packet[s] arrived) */
+		ewrk3_rx(dev);
+
+	if (csr & CSR_TNE)	/* Tx interrupt (packet sent) */
+		ewrk3_tx(dev);
+
+	/*
+	 ** Now deal with the TX/RX disable flags. These are set when there
+	 ** are no more resources. If resources free up then enable these
+	 ** interrupts, otherwise mask them - failure to do this will result
+	 ** in the system hanging in an interrupt loop.
+	 */
+	if (inb(EWRK3_FMQC)) {	/* any resources available? */
+		lp->irq_mask |= ICR_TXDM | ICR_RXDM;	/* enable the interrupt source */
+		csr &= ~(CSR_TXD | CSR_RXD);	/* ensure restart of a stalled TX or RX */
+		outb(csr, EWRK3_CSR);
+		netif_wake_queue(dev);
+	} else {
+		lp->irq_mask &= ~(ICR_TXDM | ICR_RXDM);		/* disable the interrupt source */
+	}
+
+	/* Unmask the EWRK3 board interrupts and turn off the LED */
+	cr &= ~(lp->led_mask);
+	outb(cr, EWRK3_CR);
+	ENABLE_IRQs;
+	spin_unlock(&lp->hw_lock);
+	return IRQ_HANDLED;
+}
+
+/* Called with lp->hw_lock held */
+static int ewrk3_rx(struct net_device *dev)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	u_long iobase = dev->base_addr;
+	int i, status = 0;
+	u_char page;
+	void __iomem *buf = NULL;
+
+	while (inb(EWRK3_RQC) && !status) {	/* Whilst there's incoming data */
+		if ((page = inb(EWRK3_RQ)) < lp->mPage) {	/* Get next entry's buffer page */
+			/*
+			   ** Set up shared memory window and pointer into the window
+			 */
+			if (lp->shmem_length == IO_ONLY) {
+				outb(page, EWRK3_IOPR);
+			} else if (lp->shmem_length == SHMEM_2K) {
+				buf = lp->shmem;
+				outb(page, EWRK3_MPR);
+			} else if (lp->shmem_length == SHMEM_32K) {
+				buf = (((short) page << 11) & 0x7800) + lp->shmem;
+				outb((page >> 4), EWRK3_MPR);
+			} else if (lp->shmem_length == SHMEM_64K) {
+				buf = (((short) page << 11) & 0xf800) + lp->shmem;
+				outb((page >> 5), EWRK3_MPR);
+			} else {
+				status = -1;
+				printk("%s: Oops - your private data area is hosed!\n", dev->name);
+			}
+
+			if (!status) {
+				char rx_status;
+				int pkt_len;
+
+				if (lp->shmem_length == IO_ONLY) {
+					rx_status = inb(EWRK3_DATA);
+					pkt_len = inb(EWRK3_DATA);
+					pkt_len |= ((u_short) inb(EWRK3_DATA) << 8);
+				} else {
+					rx_status = readb(buf);
+					buf += 1;
+					pkt_len = readw(buf);
+					buf += 3;
+				}
+
+				if (!(rx_status & R_ROK)) {	/* There was an error. */
+					lp->stats.rx_errors++;	/* Update the error stats. */
+					if (rx_status & R_DBE)
+						lp->stats.rx_frame_errors++;
+					if (rx_status & R_CRC)
+						lp->stats.rx_crc_errors++;
+					if (rx_status & R_PLL)
+						lp->stats.rx_fifo_errors++;
+				} else {
+					struct sk_buff *skb;
+
+					if ((skb = dev_alloc_skb(pkt_len + 2)) != NULL) {
+						unsigned char *p;
+						skb->dev = dev;
+						skb_reserve(skb, 2);	/* Align to 16 bytes */
+						p = skb_put(skb, pkt_len);
+
+						if (lp->shmem_length == IO_ONLY) {
+							*p = inb(EWRK3_DATA);	/* dummy read */
+							for (i = 0; i < pkt_len; i++) {
+								*p++ = inb(EWRK3_DATA);
+							}
+						} else {
+							memcpy_fromio(p, buf, pkt_len);
+						}
+
+						for (i = 1; i < EWRK3_PKT_STAT_SZ - 1; i++) {
+							if (pkt_len < i * EWRK3_PKT_BIN_SZ) {
+								lp->pktStats.bins[i]++;
+								i = EWRK3_PKT_STAT_SZ;
+							}
+						}
+						p = skb->data;	/* Look at the dest addr */
+						if (p[0] & 0x01) {	/* Multicast/Broadcast */
+							if ((*(s16 *) & p[0] == -1) && (*(s16 *) & p[2] == -1) && (*(s16 *) & p[4] == -1)) {
+								lp->pktStats.broadcast++;
+							} else {
+								lp->pktStats.multicast++;
+							}
+						} else if ((*(s16 *) & p[0] == *(s16 *) & dev->dev_addr[0]) &&
+							   (*(s16 *) & p[2] == *(s16 *) & dev->dev_addr[2]) &&
+							   (*(s16 *) & p[4] == *(s16 *) & dev->dev_addr[4])) {
+							lp->pktStats.unicast++;
+						}
+						lp->pktStats.bins[0]++;		/* Duplicates stats.rx_packets */
+						if (lp->pktStats.bins[0] == 0) {	/* Reset counters */
+							memset(&lp->pktStats, 0, sizeof(lp->pktStats));
+						}
+						/*
+						   ** Notify the upper protocol layers that there is another
+						   ** packet to handle
+						 */
+						skb->protocol = eth_type_trans(skb, dev);
+						netif_rx(skb);
+
+						/*
+						   ** Update stats
+						 */
+						dev->last_rx = jiffies;
+						lp->stats.rx_packets++;
+						lp->stats.rx_bytes += pkt_len;
+					} else {
+						printk("%s: Insufficient memory; nuking packet.\n", dev->name);
+						lp->stats.rx_dropped++;		/* Really, deferred. */
+						break;
+					}
+				}
+			}
+			/*
+			   ** Return the received buffer to the free memory queue
+			 */
+			outb(page, EWRK3_FMQ);
+		} else {
+			printk("ewrk3_rx(): Illegal page number, page %d\n", page);
+			printk("ewrk3_rx(): CSR: %02x ICR: %02x FMQC: %02x\n", inb(EWRK3_CSR), inb(EWRK3_ICR), inb(EWRK3_FMQC));
+		}
+	}
+	return status;
+}
+
+/*
+** Buffer sent - check for TX buffer errors.
+** Called with lp->hw_lock held
+*/
+static int ewrk3_tx(struct net_device *dev)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	u_long iobase = dev->base_addr;
+	u_char tx_status;
+
+	while ((tx_status = inb(EWRK3_TDQ)) > 0) {	/* Whilst there's old buffers */
+		if (tx_status & T_VSTS) {	/* The status is valid */
+			if (tx_status & T_TXE) {
+				lp->stats.tx_errors++;
+				if (tx_status & T_NCL)
+					lp->stats.tx_carrier_errors++;
+				if (tx_status & T_LCL)
+					lp->stats.tx_window_errors++;
+				if (tx_status & T_CTU) {
+					if ((tx_status & T_COLL) ^ T_XUR) {
+						lp->pktStats.tx_underruns++;
+					} else {
+						lp->pktStats.excessive_underruns++;
+					}
+				} else if (tx_status & T_COLL) {
+					if ((tx_status & T_COLL) ^ T_XCOLL) {
+						lp->stats.collisions++;
+					} else {
+						lp->pktStats.excessive_collisions++;
+					}
+				}
+			} else {
+				lp->stats.tx_packets++;
+			}
+		}
+	}
+
+	return 0;
+}
+
+static int ewrk3_close(struct net_device *dev)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	u_long iobase = dev->base_addr;
+	u_char icr, csr;
+
+	netif_stop_queue(dev);
+	
+	if (ewrk3_debug > 1) {
+		printk("%s: Shutting down ethercard, status was %2.2x.\n",
+		       dev->name, inb(EWRK3_CSR));
+	}
+	/*
+	   ** We stop the EWRK3 here... mask interrupts and stop TX & RX
+	 */
+	DISABLE_IRQs;
+
+	STOP_EWRK3;
+
+	/*
+	   ** Clean out the TX and RX queues here (note that one entry
+	   ** may get added to either the TXD or RX queues if the TX or RX
+	   ** just starts processing a packet before the STOP_EWRK3 command
+	   ** is received. This will be flushed in the ewrk3_open() call).
+	 */
+	while (inb(EWRK3_TQ));
+	while (inb(EWRK3_TDQ));
+	while (inb(EWRK3_RQ));
+
+	if (!lp->hard_strapped) {
+		free_irq(dev->irq, dev);
+	}
+	return 0;
+}
+
+static struct net_device_stats *ewrk3_get_stats(struct net_device *dev)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+
+	/* Null body since there is no framing error counter */
+	return &lp->stats;
+}
+
+/*
+   ** Set or clear the multicast filter for this adapter.
+ */
+static void set_multicast_list(struct net_device *dev)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	u_long iobase = dev->base_addr;
+	u_char csr;
+
+	csr = inb(EWRK3_CSR);
+
+	if (lp->shmem_length == IO_ONLY) {
+		lp->mctbl = NULL;
+	} else {
+		lp->mctbl = lp->shmem + PAGE0_HTE;
+	}
+
+	csr &= ~(CSR_PME | CSR_MCE);
+	if (dev->flags & IFF_PROMISC) {		/* set promiscuous mode */
+		csr |= CSR_PME;
+		outb(csr, EWRK3_CSR);
+	} else {
+		SetMulticastFilter(dev);
+		csr |= CSR_MCE;
+		outb(csr, EWRK3_CSR);
+	}
+}
+
+/*
+   ** Calculate the hash code and update the logical address filter
+   ** from a list of ethernet multicast addresses.
+   ** Little endian crc one liner from Matt Thomas, DEC.
+   **
+   ** Note that when clearing the table, the broadcast bit must remain asserted
+   ** to receive broadcast messages.
+ */
+static void SetMulticastFilter(struct net_device *dev)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	struct dev_mc_list *dmi = dev->mc_list;
+	u_long iobase = dev->base_addr;
+	int i;
+	char *addrs, bit, byte;
+	short __iomem *p = lp->mctbl;
+	u16 hashcode;
+	u32 crc;
+
+	spin_lock_irq(&lp->hw_lock);
+
+	if (lp->shmem_length == IO_ONLY) {
+		outb(0, EWRK3_IOPR);
+		outw(PAGE0_HTE, EWRK3_PIR1);
+	} else {
+		outb(0, EWRK3_MPR);
+	}
+
+	if (dev->flags & IFF_ALLMULTI) {
+		for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {
+			if (lp->shmem_length == IO_ONLY) {
+				outb(0xff, EWRK3_DATA);
+			} else {	/* memset didn't work here */
+				writew(0xffff, p);
+				p++;
+				i++;
+			}
+		}
+	} else {
+		/* Clear table except for broadcast bit */
+		if (lp->shmem_length == IO_ONLY) {
+			for (i = 0; i < (HASH_TABLE_LEN >> 4) - 1; i++) {
+				outb(0x00, EWRK3_DATA);
+			}
+			outb(0x80, EWRK3_DATA);
+			i++;	/* insert the broadcast bit */
+			for (; i < (HASH_TABLE_LEN >> 3); i++) {
+				outb(0x00, EWRK3_DATA);
+			}
+		} else {
+			memset_io(lp->mctbl, 0, HASH_TABLE_LEN >> 3);
+			writeb(0x80, lp->mctbl + (HASH_TABLE_LEN >> 4) - 1);
+		}
+
+		/* Update table */
+		for (i = 0; i < dev->mc_count; i++) {	/* for each address in the list */
+			addrs = dmi->dmi_addr;
+			dmi = dmi->next;
+			if ((*addrs & 0x01) == 1) {	/* multicast address? */
+				crc = ether_crc_le(ETH_ALEN, addrs);
+				hashcode = crc & ((1 << 9) - 1);	/* hashcode is 9 LSb of CRC */
+
+				byte = hashcode >> 3;	/* bit[3-8] -> byte in filter */
+				bit = 1 << (hashcode & 0x07);	/* bit[0-2] -> bit in byte */
+
+				if (lp->shmem_length == IO_ONLY) {
+					u_char tmp;
+
+					outw(PAGE0_HTE + byte, EWRK3_PIR1);
+					tmp = inb(EWRK3_DATA);
+					tmp |= bit;
+					outw(PAGE0_HTE + byte, EWRK3_PIR1);
+					outb(tmp, EWRK3_DATA);
+				} else {
+					writeb(readb(lp->mctbl + byte) | bit, lp->mctbl + byte);
+				}
+			}
+		}
+	}
+
+	spin_unlock_irq(&lp->hw_lock);
+}
+
+/*
+   ** ISA bus I/O device probe
+ */
+static int __init isa_probe(struct net_device *dev, u_long ioaddr)
+{
+	int i = num_ewrks3s, maxSlots;
+	int ret = -ENODEV;
+
+	u_long iobase;
+
+	if (ioaddr >= 0x400)
+		goto out;
+
+	if (ioaddr == 0) {	/* Autoprobing */
+		iobase = EWRK3_IO_BASE;		/* Get the first slot address */
+		maxSlots = 24;
+	} else {		/* Probe a specific location */
+		iobase = ioaddr;
+		maxSlots = i + 1;
+	}
+
+	for (; (i < maxSlots) && (dev != NULL);
+	     iobase += EWRK3_IOP_INC, i++)
+	{
+		if (request_region(iobase, EWRK3_TOTAL_SIZE, DRV_NAME)) {
+			if (DevicePresent(iobase) == 0) {
+				int irq = dev->irq;
+				ret = ewrk3_hw_init(dev, iobase);
+				if (!ret)
+					break;
+				dev->irq = irq;
+			}
+			release_region(iobase, EWRK3_TOTAL_SIZE);
+		}
+	}
+ out:
+
+	return ret;
+}
+
+/*
+   ** EISA bus I/O device probe. Probe from slot 1 since slot 0 is usually
+   ** the motherboard.
+ */
+static int __init eisa_probe(struct net_device *dev, u_long ioaddr)
+{
+	int i, maxSlots;
+	u_long iobase;
+	int ret = -ENODEV;
+
+	if (ioaddr < 0x1000)
+		goto out;
+
+	if (ioaddr == 0) {	/* Autoprobing */
+		iobase = EISA_SLOT_INC;		/* Get the first slot address */
+		i = 1;
+		maxSlots = MAX_EISA_SLOTS;
+	} else {		/* Probe a specific location */
+		iobase = ioaddr;
+		i = (ioaddr >> 12);
+		maxSlots = i + 1;
+	}
+
+	for (i = 1; (i < maxSlots) && (dev != NULL); i++, iobase += EISA_SLOT_INC) {
+		if (EISA_signature(name, EISA_ID) == 0) {
+			if (request_region(iobase, EWRK3_TOTAL_SIZE, DRV_NAME) &&
+			    DevicePresent(iobase) == 0) {
+				int irq = dev->irq;
+				ret = ewrk3_hw_init(dev, iobase);
+				if (!ret)
+					break;
+				dev->irq = irq;
+			}
+			release_region(iobase, EWRK3_TOTAL_SIZE);
+		}
+	}
+
+ out:
+	return ret;
+}
+
+
+/*
+   ** Read the EWRK3 EEPROM using this routine
+ */
+static int Read_EEPROM(u_long iobase, u_char eaddr)
+{
+	int i;
+
+	outb((eaddr & 0x3f), EWRK3_PIR1);	/* set up 6 bits of address info */
+	outb(EEPROM_RD, EWRK3_IOPR);	/* issue read command */
+	for (i = 0; i < 5000; i++)
+		inb(EWRK3_CSR);	/* wait 1msec */
+
+	return inw(EWRK3_EPROM1);	/* 16 bits data return */
+}
+
+/*
+   ** Write the EWRK3 EEPROM using this routine
+ */
+static int Write_EEPROM(short data, u_long iobase, u_char eaddr)
+{
+	int i;
+
+	outb(EEPROM_WR_EN, EWRK3_IOPR);		/* issue write enable command */
+	for (i = 0; i < 5000; i++)
+		inb(EWRK3_CSR);	/* wait 1msec */
+	outw(data, EWRK3_EPROM1);	/* write data to register */
+	outb((eaddr & 0x3f), EWRK3_PIR1);	/* set up 6 bits of address info */
+	outb(EEPROM_WR, EWRK3_IOPR);	/* issue write command */
+	for (i = 0; i < 75000; i++)
+		inb(EWRK3_CSR);	/* wait 15msec */
+	outb(EEPROM_WR_DIS, EWRK3_IOPR);	/* issue write disable command */
+	for (i = 0; i < 5000; i++)
+		inb(EWRK3_CSR);	/* wait 1msec */
+
+	return 0;
+}
+
+/*
+   ** Look for a particular board name in the on-board EEPROM.
+ */
+static void __init EthwrkSignature(char *name, char *eeprom_image)
+{
+	int i;
+	char *signatures[] = EWRK3_SIGNATURE;
+
+	for (i=0; *signatures[i] != '\0'; i++)
+		if( !strncmp(eeprom_image+EEPROM_PNAME7, signatures[i], strlen(signatures[i])) )
+			break;
+
+	if (*signatures[i] != '\0') {
+		memcpy(name, eeprom_image+EEPROM_PNAME7, EWRK3_STRLEN);
+		name[EWRK3_STRLEN] = '\0';
+	} else
+		name[0] = '\0';
+
+	return;
+}
+
+/*
+   ** Look for a special sequence in the Ethernet station address PROM that
+   ** is common across all EWRK3 products.
+   **
+   ** Search the Ethernet address ROM for the signature. Since the ROM address
+   ** counter can start at an arbitrary point, the search must include the entire
+   ** probe sequence length plus the (length_of_the_signature - 1).
+   ** Stop the search IMMEDIATELY after the signature is found so that the
+   ** PROM address counter is correctly positioned at the start of the
+   ** ethernet address for later read out.
+ */
+
+static int __init DevicePresent(u_long iobase)
+{
+	union {
+		struct {
+			u32 a;
+			u32 b;
+		} llsig;
+		char Sig[sizeof(u32) << 1];
+	}
+	dev;
+	short sigLength;
+	char data;
+	int i, j, status = 0;
+
+	dev.llsig.a = ETH_PROM_SIG;
+	dev.llsig.b = ETH_PROM_SIG;
+	sigLength = sizeof(u32) << 1;
+
+	for (i = 0, j = 0; j < sigLength && i < PROBE_LENGTH + sigLength - 1; i++) {
+		data = inb(EWRK3_APROM);
+		if (dev.Sig[j] == data) {	/* track signature */
+			j++;
+		} else {	/* lost signature; begin search again */
+			if (data == dev.Sig[0]) {
+				j = 1;
+			} else {
+				j = 0;
+			}
+		}
+	}
+
+	if (j != sigLength) {
+		status = -ENODEV;	/* search failed */
+	}
+	return status;
+}
+
+static u_char __init get_hw_addr(struct net_device *dev, u_char * eeprom_image, char chipType)
+{
+	int i, j, k;
+	u_short chksum;
+	u_char crc, lfsr, sd, status = 0;
+	u_long iobase = dev->base_addr;
+	u16 tmp;
+
+	if (chipType == LeMAC2) {
+		for (crc = 0x6a, j = 0; j < ETH_ALEN; j++) {
+			sd = dev->dev_addr[j] = eeprom_image[EEPROM_PADDR0 + j];
+			outb(dev->dev_addr[j], EWRK3_PAR0 + j);
+			for (k = 0; k < 8; k++, sd >>= 1) {
+				lfsr = ((((crc & 0x02) >> 1) ^ (crc & 0x01)) ^ (sd & 0x01)) << 7;
+				crc = (crc >> 1) + lfsr;
+			}
+		}
+		if (crc != eeprom_image[EEPROM_PA_CRC])
+			status = -1;
+	} else {
+		for (i = 0, k = 0; i < ETH_ALEN;) {
+			k <<= 1;
+			if (k > 0xffff)
+				k -= 0xffff;
+
+			k += (u_char) (tmp = inb(EWRK3_APROM));
+			dev->dev_addr[i] = (u_char) tmp;
+			outb(dev->dev_addr[i], EWRK3_PAR0 + i);
+			i++;
+			k += (u_short) ((tmp = inb(EWRK3_APROM)) << 8);
+			dev->dev_addr[i] = (u_char) tmp;
+			outb(dev->dev_addr[i], EWRK3_PAR0 + i);
+			i++;
+
+			if (k > 0xffff)
+				k -= 0xffff;
+		}
+		if (k == 0xffff)
+			k = 0;
+		chksum = inb(EWRK3_APROM);
+		chksum |= (inb(EWRK3_APROM) << 8);
+		if (k != chksum)
+			status = -1;
+	}
+
+	return status;
+}
+
+/*
+   ** Look for a particular board name in the EISA configuration space
+ */
+static int __init EISA_signature(char *name, s32 eisa_id)
+{
+	u_long i;
+	char *signatures[] = EWRK3_SIGNATURE;
+	char ManCode[EWRK3_STRLEN];
+	union {
+		s32 ID;
+		char Id[4];
+	} Eisa;
+	int status = 0;
+
+	*name = '\0';
+	for (i = 0; i < 4; i++) {
+		Eisa.Id[i] = inb(eisa_id + i);
+	}
+
+	ManCode[0] = (((Eisa.Id[0] >> 2) & 0x1f) + 0x40);
+	ManCode[1] = (((Eisa.Id[1] & 0xe0) >> 5) + ((Eisa.Id[0] & 0x03) << 3) + 0x40);
+	ManCode[2] = (((Eisa.Id[2] >> 4) & 0x0f) + 0x30);
+	ManCode[3] = ((Eisa.Id[2] & 0x0f) + 0x30);
+	ManCode[4] = (((Eisa.Id[3] >> 4) & 0x0f) + 0x30);
+	ManCode[5] = '\0';
+
+	for (i = 0; (*signatures[i] != '\0') && (*name == '\0'); i++) {
+		if (strstr(ManCode, signatures[i]) != NULL) {
+			strcpy(name, ManCode);
+			status = 1;
+		}
+	}
+
+	return status;		/* return the device name string */
+}
+
+static void ewrk3_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
+{
+	int fwrev = Read_EEPROM(dev->base_addr, EEPROM_REVLVL);
+
+	strcpy(info->driver, DRV_NAME);
+	strcpy(info->version, DRV_VERSION);
+	sprintf(info->fw_version, "%d", fwrev);
+	strcpy(info->bus_info, "N/A");
+	info->eedump_len = EEPROM_MAX;
+}
+
+static int ewrk3_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	unsigned long iobase = dev->base_addr;
+	u8 cr = inb(EWRK3_CR);
+
+	switch (lp->adapter_name[4]) {
+	case '3': /* DE203 */
+		ecmd->supported = SUPPORTED_BNC;
+		ecmd->port = PORT_BNC;
+		break;
+
+	case '4': /* DE204 */
+		ecmd->supported = SUPPORTED_TP;
+		ecmd->port = PORT_TP;
+		break;
+
+	case '5': /* DE205 */
+		ecmd->supported = SUPPORTED_TP | SUPPORTED_BNC | SUPPORTED_AUI;
+		ecmd->autoneg = !(cr & CR_APD);
+		/*
+		** Port is only valid if autoneg is disabled
+		** and even then we don't know if AUI is jumpered.
+		*/
+		if (!ecmd->autoneg)
+			ecmd->port = (cr & CR_PSEL) ? PORT_BNC : PORT_TP;
+		break;
+	}
+
+	ecmd->supported |= SUPPORTED_10baseT_Half;
+	ecmd->speed = SPEED_10;
+	ecmd->duplex = DUPLEX_HALF;
+	return 0;
+}
+
+static int ewrk3_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	unsigned long iobase = dev->base_addr;
+	unsigned long flags;
+	u8 cr;
+
+	/* DE205 is the only card with anything to set */
+	if (lp->adapter_name[4] != '5')
+		return -EOPNOTSUPP;
+
+	/* Sanity-check parameters */
+	if (ecmd->speed != SPEED_10)
+		return -EINVAL;
+	if (ecmd->port != PORT_TP && ecmd->port != PORT_BNC)
+		return -EINVAL; /* AUI is not software-selectable */
+	if (ecmd->transceiver != XCVR_INTERNAL)
+		return -EINVAL;
+	if (ecmd->duplex != DUPLEX_HALF)
+		return -EINVAL;
+	if (ecmd->phy_address != 0)
+		return -EINVAL;
+
+	spin_lock_irqsave(&lp->hw_lock, flags);
+	cr = inb(EWRK3_CR);
+
+	/* If Autoneg is set, change to Auto Port mode */
+	/* Otherwise, disable Auto Port and set port explicitly */
+	if (ecmd->autoneg) {
+		cr &= ~CR_APD;
+	} else {
+		cr |= CR_APD;
+		if (ecmd->port == PORT_TP)
+			cr &= ~CR_PSEL;		/* Force TP */
+		else
+			cr |= CR_PSEL;		/* Force BNC */
+	}
+
+	/* Commit the changes */
+	outb(cr, EWRK3_CR);
+	spin_unlock_irqrestore(&lp->hw_lock, flags);
+	return 0;
+}
+
+static u32 ewrk3_get_link(struct net_device *dev)
+{
+	unsigned long iobase = dev->base_addr;
+	u8 cmr = inb(EWRK3_CMR);
+	/* DE203 has BNC only and link status does not apply */
+	/* On DE204 this is always valid since TP is the only port. */
+	/* On DE205 this reflects TP status even if BNC or AUI is selected. */
+	return !(cmr & CMR_LINK);
+}
+
+static int ewrk3_phys_id(struct net_device *dev, u32 data)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	unsigned long iobase = dev->base_addr;
+	unsigned long flags;
+	u8 cr;
+	int count;
+
+	/* Toggle LED 4x per second */
+	count = data << 2;
+
+	spin_lock_irqsave(&lp->hw_lock, flags);
+
+	/* Bail if a PHYS_ID is already in progress */
+	if (lp->led_mask == 0) {
+		spin_unlock_irqrestore(&lp->hw_lock, flags);
+		return -EBUSY;
+	}
+
+	/* Prevent ISR from twiddling the LED */
+	lp->led_mask = 0;
+
+	while (count--) {
+		/* Toggle the LED */
+		cr = inb(EWRK3_CR);
+		outb(cr ^ CR_LED, EWRK3_CR);
+
+		/* Wait a little while */
+		spin_unlock_irqrestore(&lp->hw_lock, flags);
+		msleep(250);
+		spin_lock_irqsave(&lp->hw_lock, flags);
+
+		/* Exit if we got a signal */
+		if (signal_pending(current))
+			break;
+	}
+
+	lp->led_mask = CR_LED;
+	cr = inb(EWRK3_CR);
+	outb(cr & ~CR_LED, EWRK3_CR);
+	spin_unlock_irqrestore(&lp->hw_lock, flags);
+	return signal_pending(current) ? -ERESTARTSYS : 0;
+}
+
+static struct ethtool_ops ethtool_ops_203 = {
+	.get_drvinfo = ewrk3_get_drvinfo,
+	.get_settings = ewrk3_get_settings,
+	.set_settings = ewrk3_set_settings,
+	.phys_id = ewrk3_phys_id,
+};
+
+static struct ethtool_ops ethtool_ops = {
+	.get_drvinfo = ewrk3_get_drvinfo,
+	.get_settings = ewrk3_get_settings,
+	.set_settings = ewrk3_set_settings,
+	.get_link = ewrk3_get_link,
+	.phys_id = ewrk3_phys_id,
+};
+
+/*
+   ** Perform IOCTL call functions here. Some are privileged operations and the
+   ** effective uid is checked in those cases.
+ */
+static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+{
+	struct ewrk3_private *lp = netdev_priv(dev);
+	struct ewrk3_ioctl *ioc = (struct ewrk3_ioctl *) &rq->ifr_ifru;
+	u_long iobase = dev->base_addr;
+	int i, j, status = 0;
+	u_char csr;
+	unsigned long flags;
+	union ewrk3_addr {
+		u_char addr[HASH_TABLE_LEN * ETH_ALEN];
+		u_short val[(HASH_TABLE_LEN * ETH_ALEN) >> 1];
+	};
+	
+	union ewrk3_addr *tmp;
+
+	/* All we handle are private IOCTLs */
+	if (cmd != EWRK3IOCTL)
+		return -EOPNOTSUPP;
+
+	tmp = kmalloc(sizeof(union ewrk3_addr), GFP_KERNEL);
+	if(tmp==NULL)
+		return -ENOMEM;
+
+	switch (ioc->cmd) {
+	case EWRK3_GET_HWADDR:	/* Get the hardware address */
+		for (i = 0; i < ETH_ALEN; i++) {
+			tmp->addr[i] = dev->dev_addr[i];
+		}
+		ioc->len = ETH_ALEN;
+		if (copy_to_user(ioc->data, tmp->addr, ioc->len))
+			status = -EFAULT;
+		break;
+		
+	case EWRK3_SET_HWADDR:	/* Set the hardware address */
+		if (capable(CAP_NET_ADMIN)) {
+			spin_lock_irqsave(&lp->hw_lock, flags);
+			csr = inb(EWRK3_CSR);
+			csr |= (CSR_TXD | CSR_RXD);
+			outb(csr, EWRK3_CSR);	/* Disable the TX and RX */
+			spin_unlock_irqrestore(&lp->hw_lock, flags);
+
+			if (copy_from_user(tmp->addr, ioc->data, ETH_ALEN)) {
+				status = -EFAULT;
+				break;
+			}
+			spin_lock_irqsave(&lp->hw_lock, flags);
+			for (i = 0; i < ETH_ALEN; i++) {
+				dev->dev_addr[i] = tmp->addr[i];
+				outb(tmp->addr[i], EWRK3_PAR0 + i);
+			}
+
+			csr = inb(EWRK3_CSR);
+			csr &= ~(CSR_TXD | CSR_RXD);	/* Enable the TX and RX */
+			outb(csr, EWRK3_CSR);
+			spin_unlock_irqrestore(&lp->hw_lock, flags);
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	case EWRK3_SET_PROM:	/* Set Promiscuous Mode */
+		if (capable(CAP_NET_ADMIN)) {
+			spin_lock_irqsave(&lp->hw_lock, flags);
+			csr = inb(EWRK3_CSR);
+			csr |= CSR_PME;
+			csr &= ~CSR_MCE;
+			outb(csr, EWRK3_CSR);
+			spin_unlock_irqrestore(&lp->hw_lock, flags);
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	case EWRK3_CLR_PROM:	/* Clear Promiscuous Mode */
+		if (capable(CAP_NET_ADMIN)) {
+			spin_lock_irqsave(&lp->hw_lock, flags);
+			csr = inb(EWRK3_CSR);
+			csr &= ~CSR_PME;
+			outb(csr, EWRK3_CSR);
+			spin_unlock_irqrestore(&lp->hw_lock, flags);
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	case EWRK3_GET_MCA:	/* Get the multicast address table */
+		spin_lock_irqsave(&lp->hw_lock, flags);
+		if (lp->shmem_length == IO_ONLY) {
+			outb(0, EWRK3_IOPR);
+			outw(PAGE0_HTE, EWRK3_PIR1);
+			for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {
+				tmp->addr[i] = inb(EWRK3_DATA);
+			}
+		} else {
+			outb(0, EWRK3_MPR);
+			memcpy_fromio(tmp->addr, lp->shmem + PAGE0_HTE, (HASH_TABLE_LEN >> 3));
+		}
+		spin_unlock_irqrestore(&lp->hw_lock, flags);
+
+		ioc->len = (HASH_TABLE_LEN >> 3);
+		if (copy_to_user(ioc->data, tmp->addr, ioc->len))
+			status = -EFAULT;
+
+		break;
+	case EWRK3_SET_MCA:	/* Set a multicast address */
+		if (capable(CAP_NET_ADMIN)) {
+			if (ioc->len > 1024)
+			{
+				status = -EINVAL;
+				break;
+			}
+			if (copy_from_user(tmp->addr, ioc->data, ETH_ALEN * ioc->len)) {
+				status = -EFAULT;
+				break;
+			}
+			set_multicast_list(dev);
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	case EWRK3_CLR_MCA:	/* Clear all multicast addresses */
+		if (capable(CAP_NET_ADMIN)) {
+			set_multicast_list(dev);
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	case EWRK3_MCA_EN:	/* Enable multicast addressing */
+		if (capable(CAP_NET_ADMIN)) {
+			spin_lock_irqsave(&lp->hw_lock, flags);
+			csr = inb(EWRK3_CSR);
+			csr |= CSR_MCE;
+			csr &= ~CSR_PME;
+			outb(csr, EWRK3_CSR);
+			spin_unlock_irqrestore(&lp->hw_lock, flags);
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	case EWRK3_GET_STATS: { /* Get the driver statistics */
+		struct ewrk3_stats *tmp_stats =
+        		kmalloc(sizeof(lp->pktStats), GFP_KERNEL);
+		if (!tmp_stats) {
+			status = -ENOMEM;
+			break;
+		}
+
+		spin_lock_irqsave(&lp->hw_lock, flags);
+		memcpy(tmp_stats, &lp->pktStats, sizeof(lp->pktStats));
+		spin_unlock_irqrestore(&lp->hw_lock, flags);
+
+		ioc->len = sizeof(lp->pktStats);
+		if (copy_to_user(ioc->data, tmp_stats, sizeof(lp->pktStats)))
+    			status = -EFAULT;
+		kfree(tmp_stats);
+		break;
+	}
+	case EWRK3_CLR_STATS:	/* Zero out the driver statistics */
+		if (capable(CAP_NET_ADMIN)) {
+			spin_lock_irqsave(&lp->hw_lock, flags);
+			memset(&lp->pktStats, 0, sizeof(lp->pktStats));
+			spin_unlock_irqrestore(&lp->hw_lock,flags);
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	case EWRK3_GET_CSR:	/* Get the CSR Register contents */
+		tmp->addr[0] = inb(EWRK3_CSR);
+		ioc->len = 1;
+		if (copy_to_user(ioc->data, tmp->addr, ioc->len))
+			status = -EFAULT;
+		break;
+	case EWRK3_SET_CSR:	/* Set the CSR Register contents */
+		if (capable(CAP_NET_ADMIN)) {
+			if (copy_from_user(tmp->addr, ioc->data, 1)) {
+				status = -EFAULT;
+				break;
+			}
+			outb(tmp->addr[0], EWRK3_CSR);
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	case EWRK3_GET_EEPROM:	/* Get the EEPROM contents */
+		if (capable(CAP_NET_ADMIN)) {
+			for (i = 0; i < (EEPROM_MAX >> 1); i++) {
+				tmp->val[i] = (short) Read_EEPROM(iobase, i);
+			}
+			i = EEPROM_MAX;
+			tmp->addr[i++] = inb(EWRK3_CMR);		/* Config/Management Reg. */
+			for (j = 0; j < ETH_ALEN; j++) {
+				tmp->addr[i++] = inb(EWRK3_PAR0 + j);
+			}
+			ioc->len = EEPROM_MAX + 1 + ETH_ALEN;
+			if (copy_to_user(ioc->data, tmp->addr, ioc->len))
+				status = -EFAULT;
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	case EWRK3_SET_EEPROM:	/* Set the EEPROM contents */
+		if (capable(CAP_NET_ADMIN)) {
+			if (copy_from_user(tmp->addr, ioc->data, EEPROM_MAX)) {
+				status = -EFAULT;
+				break;
+			}
+			for (i = 0; i < (EEPROM_MAX >> 1); i++) {
+				Write_EEPROM(tmp->val[i], iobase, i);
+			}
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	case EWRK3_GET_CMR:	/* Get the CMR Register contents */
+		tmp->addr[0] = inb(EWRK3_CMR);
+		ioc->len = 1;
+		if (copy_to_user(ioc->data, tmp->addr, ioc->len))
+			status = -EFAULT;
+		break;
+	case EWRK3_SET_TX_CUT_THRU:	/* Set TX cut through mode */
+		if (capable(CAP_NET_ADMIN)) {
+			lp->txc = 1;
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	case EWRK3_CLR_TX_CUT_THRU:	/* Clear TX cut through mode */
+		if (capable(CAP_NET_ADMIN)) {
+			lp->txc = 0;
+		} else {
+			status = -EPERM;
+		}
+
+		break;
+	default:
+		status = -EOPNOTSUPP;
+	}
+	kfree(tmp);
+	return status;
+}
+
+#ifdef MODULE
+static struct net_device *ewrk3_devs[MAX_NUM_EWRK3S];
+static int ndevs;
+static int io[MAX_NUM_EWRK3S+1] = { 0x300, 0, };
+
+/* '21' below should really be 'MAX_NUM_EWRK3S' */
+module_param_array(io, int, NULL, 0);
+module_param_array(irq, int, NULL, 0);
+MODULE_PARM_DESC(io, "EtherWORKS 3 I/O base address(es)");
+MODULE_PARM_DESC(irq, "EtherWORKS 3 IRQ number(s)");
+
+static __exit void ewrk3_exit_module(void)
+{
+	int i;
+
+	for( i=0; i<ndevs; i++ ) {
+		struct net_device *dev = ewrk3_devs[i];
+		struct ewrk3_private *lp = netdev_priv(dev);
+		ewrk3_devs[i] = NULL;
+		unregister_netdev(dev);
+		release_region(dev->base_addr, EWRK3_TOTAL_SIZE);
+		iounmap(lp->shmem);
+		free_netdev(dev);
+	}
+}
+
+static __init int ewrk3_init_module(void)
+{
+	int i=0;
+
+	while( io[i] && irq[i] ) {
+		struct net_device *dev
+			= alloc_etherdev(sizeof(struct ewrk3_private));
+
+		if (!dev)
+			break;
+
+		if (ewrk3_probe1(dev, io[i], irq[i]) != 0) {
+			free_netdev(dev);
+			break;
+		}
+
+		ewrk3_devs[ndevs++] = dev;
+		i++;
+	}
+
+	return ndevs ? 0 : -EIO;
+}
+
+
+/* Hack for breakage in new module stuff */
+module_exit(ewrk3_exit_module);
+module_init(ewrk3_init_module);
+#endif				/* MODULE */
+MODULE_LICENSE("GPL");
+
+
+
+/*
+ * Local variables:
+ *  compile-command: "gcc -D__KERNEL__ -I/linux/include -Wall -Wstrict-prototypes -fomit-frame-pointer -fno-strength-reduce -malign-loops=2 -malign-jumps=2 -malign-functions=2 -O2 -m486 -c ewrk3.c"
+ *
+ *  compile-command: "gcc -D__KERNEL__ -DMODULE -I/linux/include -Wall -Wstrict-prototypes -fomit-frame-pointer -fno-strength-reduce -malign-loops=2 -malign-jumps=2 -malign-functions=2 -O2 -m486 -c ewrk3.c"
+ * End:
+ */