diff --git a/drivers/net/via-velocity.c b/drivers/net/via-velocity.c
new file mode 100644
index 0000000..15e7102
--- /dev/null
+++ b/drivers/net/via-velocity.c
@@ -0,0 +1,3303 @@
+/*
+ * This code is derived from the VIA reference driver (copyright message
+ * below) provided to Red Hat by VIA Networking Technologies, Inc. for
+ * addition to the Linux kernel.
+ *
+ * The code has been merged into one source file, cleaned up to follow
+ * Linux coding style,  ported to the Linux 2.6 kernel tree and cleaned
+ * for 64bit hardware platforms.
+ *
+ * TODO
+ *	Big-endian support
+ *	rx_copybreak/alignment
+ *	Scatter gather
+ *	More testing
+ *
+ * The changes are (c) Copyright 2004, Red Hat Inc. <alan@redhat.com>
+ * Additional fixes and clean up: Francois Romieu
+ *
+ * This source has not been verified for use in safety critical systems.
+ *
+ * Please direct queries about the revamped driver to the linux-kernel
+ * list not VIA.
+ *
+ * Original code:
+ *
+ * Copyright (c) 1996, 2003 VIA Networking Technologies, Inc.
+ * All rights reserved.
+ *
+ * This software may be redistributed and/or modified under
+ * the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
+ * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * Author: Chuang Liang-Shing, AJ Jiang
+ *
+ * Date: Jan 24, 2003
+ *
+ * MODULE_LICENSE("GPL");
+ *
+ */
+
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/version.h>
+#include <linux/string.h>
+#include <linux/wait.h>
+#include <asm/io.h>
+#include <linux/if.h>
+#include <linux/config.h>
+#include <asm/uaccess.h>
+#include <linux/proc_fs.h>
+#include <linux/inetdevice.h>
+#include <linux/reboot.h>
+#include <linux/ethtool.h>
+#include <linux/mii.h>
+#include <linux/in.h>
+#include <linux/if_arp.h>
+#include <linux/ip.h>
+#include <linux/tcp.h>
+#include <linux/udp.h>
+#include <linux/crc-ccitt.h>
+#include <linux/crc32.h>
+
+#include "via-velocity.h"
+
+
+static int velocity_nics = 0;
+static int msglevel = MSG_LEVEL_INFO;
+
+
+static int velocity_mii_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd);
+static struct ethtool_ops velocity_ethtool_ops;
+
+/*
+    Define module options
+*/
+
+MODULE_AUTHOR("VIA Networking Technologies, Inc.");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("VIA Networking Velocity Family Gigabit Ethernet Adapter Driver");
+
+#define VELOCITY_PARAM(N,D) \
+        static int N[MAX_UNITS]=OPTION_DEFAULT;\
+	module_param_array(N, int, NULL, 0); \
+        MODULE_PARM_DESC(N, D);
+
+#define RX_DESC_MIN     64
+#define RX_DESC_MAX     255
+#define RX_DESC_DEF     64
+VELOCITY_PARAM(RxDescriptors, "Number of receive descriptors");
+
+#define TX_DESC_MIN     16
+#define TX_DESC_MAX     256
+#define TX_DESC_DEF     64
+VELOCITY_PARAM(TxDescriptors, "Number of transmit descriptors");
+
+#define VLAN_ID_MIN     0
+#define VLAN_ID_MAX     4095
+#define VLAN_ID_DEF     0
+/* VID_setting[] is used for setting the VID of NIC.
+   0: default VID.
+   1-4094: other VIDs.
+*/
+VELOCITY_PARAM(VID_setting, "802.1Q VLAN ID");
+
+#define RX_THRESH_MIN   0
+#define RX_THRESH_MAX   3
+#define RX_THRESH_DEF   0
+/* rx_thresh[] is used for controlling the receive fifo threshold.
+   0: indicate the rxfifo threshold is 128 bytes.
+   1: indicate the rxfifo threshold is 512 bytes.
+   2: indicate the rxfifo threshold is 1024 bytes.
+   3: indicate the rxfifo threshold is store & forward.
+*/
+VELOCITY_PARAM(rx_thresh, "Receive fifo threshold");
+
+#define DMA_LENGTH_MIN  0
+#define DMA_LENGTH_MAX  7
+#define DMA_LENGTH_DEF  0
+
+/* DMA_length[] is used for controlling the DMA length
+   0: 8 DWORDs
+   1: 16 DWORDs
+   2: 32 DWORDs
+   3: 64 DWORDs
+   4: 128 DWORDs
+   5: 256 DWORDs
+   6: SF(flush till emply)
+   7: SF(flush till emply)
+*/
+VELOCITY_PARAM(DMA_length, "DMA length");
+
+#define TAGGING_DEF     0
+/* enable_tagging[] is used for enabling 802.1Q VID tagging.
+   0: disable VID seeting(default).
+   1: enable VID setting.
+*/
+VELOCITY_PARAM(enable_tagging, "Enable 802.1Q tagging");
+
+#define IP_ALIG_DEF     0
+/* IP_byte_align[] is used for IP header DWORD byte aligned
+   0: indicate the IP header won't be DWORD byte aligned.(Default) .
+   1: indicate the IP header will be DWORD byte aligned.
+      In some enviroment, the IP header should be DWORD byte aligned,
+      or the packet will be droped when we receive it. (eg: IPVS)
+*/
+VELOCITY_PARAM(IP_byte_align, "Enable IP header dword aligned");
+
+#define TX_CSUM_DEF     1
+/* txcsum_offload[] is used for setting the checksum offload ability of NIC.
+   (We only support RX checksum offload now)
+   0: disable csum_offload[checksum offload
+   1: enable checksum offload. (Default)
+*/
+VELOCITY_PARAM(txcsum_offload, "Enable transmit packet checksum offload");
+
+#define FLOW_CNTL_DEF   1
+#define FLOW_CNTL_MIN   1
+#define FLOW_CNTL_MAX   5
+
+/* flow_control[] is used for setting the flow control ability of NIC.
+   1: hardware deafult - AUTO (default). Use Hardware default value in ANAR.
+   2: enable TX flow control.
+   3: enable RX flow control.
+   4: enable RX/TX flow control.
+   5: disable
+*/
+VELOCITY_PARAM(flow_control, "Enable flow control ability");
+
+#define MED_LNK_DEF 0
+#define MED_LNK_MIN 0
+#define MED_LNK_MAX 4
+/* speed_duplex[] is used for setting the speed and duplex mode of NIC.
+   0: indicate autonegotiation for both speed and duplex mode
+   1: indicate 100Mbps half duplex mode
+   2: indicate 100Mbps full duplex mode
+   3: indicate 10Mbps half duplex mode
+   4: indicate 10Mbps full duplex mode
+
+   Note:
+        if EEPROM have been set to the force mode, this option is ignored
+            by driver.
+*/
+VELOCITY_PARAM(speed_duplex, "Setting the speed and duplex mode");
+
+#define VAL_PKT_LEN_DEF     0
+/* ValPktLen[] is used for setting the checksum offload ability of NIC.
+   0: Receive frame with invalid layer 2 length (Default)
+   1: Drop frame with invalid layer 2 length
+*/
+VELOCITY_PARAM(ValPktLen, "Receiving or Drop invalid 802.3 frame");
+
+#define WOL_OPT_DEF     0
+#define WOL_OPT_MIN     0
+#define WOL_OPT_MAX     7
+/* wol_opts[] is used for controlling wake on lan behavior.
+   0: Wake up if recevied a magic packet. (Default)
+   1: Wake up if link status is on/off.
+   2: Wake up if recevied an arp packet.
+   4: Wake up if recevied any unicast packet.
+   Those value can be sumed up to support more than one option.
+*/
+VELOCITY_PARAM(wol_opts, "Wake On Lan options");
+
+#define INT_WORKS_DEF   20
+#define INT_WORKS_MIN   10
+#define INT_WORKS_MAX   64
+
+VELOCITY_PARAM(int_works, "Number of packets per interrupt services");
+
+static int rx_copybreak = 200;
+module_param(rx_copybreak, int, 0644);
+MODULE_PARM_DESC(rx_copybreak, "Copy breakpoint for copy-only-tiny-frames");
+
+static void velocity_init_info(struct pci_dev *pdev, struct velocity_info *vptr, struct velocity_info_tbl *info);
+static int velocity_get_pci_info(struct velocity_info *, struct pci_dev *pdev);
+static void velocity_print_info(struct velocity_info *vptr);
+static int velocity_open(struct net_device *dev);
+static int velocity_change_mtu(struct net_device *dev, int mtu);
+static int velocity_xmit(struct sk_buff *skb, struct net_device *dev);
+static int velocity_intr(int irq, void *dev_instance, struct pt_regs *regs);
+static void velocity_set_multi(struct net_device *dev);
+static struct net_device_stats *velocity_get_stats(struct net_device *dev);
+static int velocity_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
+static int velocity_close(struct net_device *dev);
+static int velocity_receive_frame(struct velocity_info *, int idx);
+static int velocity_alloc_rx_buf(struct velocity_info *, int idx);
+static void velocity_free_rd_ring(struct velocity_info *vptr);
+static void velocity_free_tx_buf(struct velocity_info *vptr, struct velocity_td_info *);
+static int velocity_soft_reset(struct velocity_info *vptr);
+static void mii_init(struct velocity_info *vptr, u32 mii_status);
+static u32 velocity_get_opt_media_mode(struct velocity_info *vptr);
+static void velocity_print_link_status(struct velocity_info *vptr);
+static void safe_disable_mii_autopoll(struct mac_regs __iomem * regs);
+static void velocity_shutdown(struct velocity_info *vptr);
+static void enable_flow_control_ability(struct velocity_info *vptr);
+static void enable_mii_autopoll(struct mac_regs __iomem * regs);
+static int velocity_mii_read(struct mac_regs __iomem *, u8 byIdx, u16 * pdata);
+static int velocity_mii_write(struct mac_regs __iomem *, u8 byMiiAddr, u16 data);
+static u32 mii_check_media_mode(struct mac_regs __iomem * regs);
+static u32 check_connection_type(struct mac_regs __iomem * regs);
+static int velocity_set_media_mode(struct velocity_info *vptr, u32 mii_status);
+
+#ifdef CONFIG_PM
+
+static int velocity_suspend(struct pci_dev *pdev, pm_message_t state);
+static int velocity_resume(struct pci_dev *pdev);
+
+static int velocity_netdev_event(struct notifier_block *nb, unsigned long notification, void *ptr);
+
+static struct notifier_block velocity_inetaddr_notifier = {
+      .notifier_call	= velocity_netdev_event,
+};
+
+static DEFINE_SPINLOCK(velocity_dev_list_lock);
+static LIST_HEAD(velocity_dev_list);
+
+static void velocity_register_notifier(void)
+{
+	register_inetaddr_notifier(&velocity_inetaddr_notifier);
+}
+
+static void velocity_unregister_notifier(void)
+{
+	unregister_inetaddr_notifier(&velocity_inetaddr_notifier);
+}
+
+#else				/* CONFIG_PM */
+
+#define velocity_register_notifier()	do {} while (0)
+#define velocity_unregister_notifier()	do {} while (0)
+
+#endif				/* !CONFIG_PM */
+
+/*
+ *	Internal board variants. At the moment we have only one
+ */
+
+static struct velocity_info_tbl chip_info_table[] = {
+	{CHIP_TYPE_VT6110, "VIA Networking Velocity Family Gigabit Ethernet Adapter", 256, 1, 0x00FFFFFFUL},
+	{0, NULL}
+};
+
+/*
+ *	Describe the PCI device identifiers that we support in this
+ *	device driver. Used for hotplug autoloading.
+ */
+
+static struct pci_device_id velocity_id_table[] __devinitdata = {
+	{PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_612X,
+	 PCI_ANY_ID, PCI_ANY_ID, 0, 0, (unsigned long) chip_info_table},
+	{0, }
+};
+
+MODULE_DEVICE_TABLE(pci, velocity_id_table);
+
+/**
+ *	get_chip_name	- 	identifier to name
+ *	@id: chip identifier
+ *
+ *	Given a chip identifier return a suitable description. Returns
+ *	a pointer a static string valid while the driver is loaded.
+ */
+
+static char __devinit *get_chip_name(enum chip_type chip_id)
+{
+	int i;
+	for (i = 0; chip_info_table[i].name != NULL; i++)
+		if (chip_info_table[i].chip_id == chip_id)
+			break;
+	return chip_info_table[i].name;
+}
+
+/**
+ *	velocity_remove1	-	device unplug
+ *	@pdev: PCI device being removed
+ *
+ *	Device unload callback. Called on an unplug or on module
+ *	unload for each active device that is present. Disconnects
+ *	the device from the network layer and frees all the resources
+ */
+
+static void __devexit velocity_remove1(struct pci_dev *pdev)
+{
+	struct net_device *dev = pci_get_drvdata(pdev);
+	struct velocity_info *vptr = dev->priv;
+
+#ifdef CONFIG_PM
+	unsigned long flags;
+
+	spin_lock_irqsave(&velocity_dev_list_lock, flags);
+	if (!list_empty(&velocity_dev_list))
+		list_del(&vptr->list);
+	spin_unlock_irqrestore(&velocity_dev_list_lock, flags);
+#endif
+	unregister_netdev(dev);
+	iounmap(vptr->mac_regs);
+	pci_release_regions(pdev);
+	pci_disable_device(pdev);
+	pci_set_drvdata(pdev, NULL);
+	free_netdev(dev);
+
+	velocity_nics--;
+}
+
+/**
+ *	velocity_set_int_opt	-	parser for integer options
+ *	@opt: pointer to option value
+ *	@val: value the user requested (or -1 for default)
+ *	@min: lowest value allowed
+ *	@max: highest value allowed
+ *	@def: default value
+ *	@name: property name
+ *	@dev: device name
+ *
+ *	Set an integer property in the module options. This function does
+ *	all the verification and checking as well as reporting so that
+ *	we don't duplicate code for each option.
+ */
+
+static void __devinit velocity_set_int_opt(int *opt, int val, int min, int max, int def, char *name, char *devname)
+{
+	if (val == -1)
+		*opt = def;
+	else if (val < min || val > max) {
+		VELOCITY_PRT(MSG_LEVEL_INFO, KERN_NOTICE "%s: the value of parameter %s is invalid, the valid range is (%d-%d)\n",
+					devname, name, min, max);
+		*opt = def;
+	} else {
+		VELOCITY_PRT(MSG_LEVEL_INFO, KERN_INFO "%s: set value of parameter %s to %d\n",
+					devname, name, val);
+		*opt = val;
+	}
+}
+
+/**
+ *	velocity_set_bool_opt	-	parser for boolean options
+ *	@opt: pointer to option value
+ *	@val: value the user requested (or -1 for default)
+ *	@def: default value (yes/no)
+ *	@flag: numeric value to set for true.
+ *	@name: property name
+ *	@dev: device name
+ *
+ *	Set a boolean property in the module options. This function does
+ *	all the verification and checking as well as reporting so that
+ *	we don't duplicate code for each option.
+ */
+
+static void __devinit velocity_set_bool_opt(u32 * opt, int val, int def, u32 flag, char *name, char *devname)
+{
+	(*opt) &= (~flag);
+	if (val == -1)
+		*opt |= (def ? flag : 0);
+	else if (val < 0 || val > 1) {
+		printk(KERN_NOTICE "%s: the value of parameter %s is invalid, the valid range is (0-1)\n", 
+			devname, name);
+		*opt |= (def ? flag : 0);
+	} else {
+		printk(KERN_INFO "%s: set parameter %s to %s\n", 
+			devname, name, val ? "TRUE" : "FALSE");
+		*opt |= (val ? flag : 0);
+	}
+}
+
+/**
+ *	velocity_get_options	-	set options on device
+ *	@opts: option structure for the device
+ *	@index: index of option to use in module options array
+ *	@devname: device name
+ *
+ *	Turn the module and command options into a single structure
+ *	for the current device
+ */
+
+static void __devinit velocity_get_options(struct velocity_opt *opts, int index, char *devname)
+{
+
+	velocity_set_int_opt(&opts->rx_thresh, rx_thresh[index], RX_THRESH_MIN, RX_THRESH_MAX, RX_THRESH_DEF, "rx_thresh", devname);
+	velocity_set_int_opt(&opts->DMA_length, DMA_length[index], DMA_LENGTH_MIN, DMA_LENGTH_MAX, DMA_LENGTH_DEF, "DMA_length", devname);
+	velocity_set_int_opt(&opts->numrx, RxDescriptors[index], RX_DESC_MIN, RX_DESC_MAX, RX_DESC_DEF, "RxDescriptors", devname);
+	velocity_set_int_opt(&opts->numtx, TxDescriptors[index], TX_DESC_MIN, TX_DESC_MAX, TX_DESC_DEF, "TxDescriptors", devname);
+	velocity_set_int_opt(&opts->vid, VID_setting[index], VLAN_ID_MIN, VLAN_ID_MAX, VLAN_ID_DEF, "VID_setting", devname);
+	velocity_set_bool_opt(&opts->flags, enable_tagging[index], TAGGING_DEF, VELOCITY_FLAGS_TAGGING, "enable_tagging", devname);
+	velocity_set_bool_opt(&opts->flags, txcsum_offload[index], TX_CSUM_DEF, VELOCITY_FLAGS_TX_CSUM, "txcsum_offload", devname);
+	velocity_set_int_opt(&opts->flow_cntl, flow_control[index], FLOW_CNTL_MIN, FLOW_CNTL_MAX, FLOW_CNTL_DEF, "flow_control", devname);
+	velocity_set_bool_opt(&opts->flags, IP_byte_align[index], IP_ALIG_DEF, VELOCITY_FLAGS_IP_ALIGN, "IP_byte_align", devname);
+	velocity_set_bool_opt(&opts->flags, ValPktLen[index], VAL_PKT_LEN_DEF, VELOCITY_FLAGS_VAL_PKT_LEN, "ValPktLen", devname);
+	velocity_set_int_opt((int *) &opts->spd_dpx, speed_duplex[index], MED_LNK_MIN, MED_LNK_MAX, MED_LNK_DEF, "Media link mode", devname);
+	velocity_set_int_opt((int *) &opts->wol_opts, wol_opts[index], WOL_OPT_MIN, WOL_OPT_MAX, WOL_OPT_DEF, "Wake On Lan options", devname);
+	velocity_set_int_opt((int *) &opts->int_works, int_works[index], INT_WORKS_MIN, INT_WORKS_MAX, INT_WORKS_DEF, "Interrupt service works", devname);
+	opts->numrx = (opts->numrx & ~3);
+}
+
+/**
+ *	velocity_init_cam_filter	-	initialise CAM
+ *	@vptr: velocity to program
+ *
+ *	Initialize the content addressable memory used for filters. Load
+ *	appropriately according to the presence of VLAN
+ */
+
+static void velocity_init_cam_filter(struct velocity_info *vptr)
+{
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+
+	/* Turn on MCFG_PQEN, turn off MCFG_RTGOPT */
+	WORD_REG_BITS_SET(MCFG_PQEN, MCFG_RTGOPT, &regs->MCFG);
+	WORD_REG_BITS_ON(MCFG_VIDFR, &regs->MCFG);
+
+	/* Disable all CAMs */
+	memset(vptr->vCAMmask, 0, sizeof(u8) * 8);
+	memset(vptr->mCAMmask, 0, sizeof(u8) * 8);
+	mac_set_cam_mask(regs, vptr->vCAMmask, VELOCITY_VLAN_ID_CAM);
+	mac_set_cam_mask(regs, vptr->mCAMmask, VELOCITY_MULTICAST_CAM);
+
+	/* Enable first VCAM */
+	if (vptr->flags & VELOCITY_FLAGS_TAGGING) {
+		/* If Tagging option is enabled and VLAN ID is not zero, then
+		   turn on MCFG_RTGOPT also */
+		if (vptr->options.vid != 0)
+			WORD_REG_BITS_ON(MCFG_RTGOPT, &regs->MCFG);
+
+		mac_set_cam(regs, 0, (u8 *) & (vptr->options.vid), VELOCITY_VLAN_ID_CAM);
+		vptr->vCAMmask[0] |= 1;
+		mac_set_cam_mask(regs, vptr->vCAMmask, VELOCITY_VLAN_ID_CAM);
+	} else {
+		u16 temp = 0;
+		mac_set_cam(regs, 0, (u8 *) &temp, VELOCITY_VLAN_ID_CAM);
+		temp = 1;
+		mac_set_cam_mask(regs, (u8 *) &temp, VELOCITY_VLAN_ID_CAM);
+	}
+}
+
+/**
+ *	velocity_rx_reset	-	handle a receive reset
+ *	@vptr: velocity we are resetting
+ *
+ *	Reset the ownership and status for the receive ring side.
+ *	Hand all the receive queue to the NIC.
+ */
+
+static void velocity_rx_reset(struct velocity_info *vptr)
+{
+
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+	int i;
+
+	vptr->rd_dirty = vptr->rd_filled = vptr->rd_curr = 0;
+
+	/*
+	 *	Init state, all RD entries belong to the NIC
+	 */
+	for (i = 0; i < vptr->options.numrx; ++i)
+		vptr->rd_ring[i].rdesc0.owner = OWNED_BY_NIC;
+
+	writew(vptr->options.numrx, &regs->RBRDU);
+	writel(vptr->rd_pool_dma, &regs->RDBaseLo);
+	writew(0, &regs->RDIdx);
+	writew(vptr->options.numrx - 1, &regs->RDCSize);
+}
+
+/**
+ *	velocity_init_registers	-	initialise MAC registers
+ *	@vptr: velocity to init
+ *	@type: type of initialisation (hot or cold)
+ *
+ *	Initialise the MAC on a reset or on first set up on the
+ *	hardware.
+ */
+
+static void velocity_init_registers(struct velocity_info *vptr, 
+				    enum velocity_init_type type)
+{
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+	int i, mii_status;
+
+	mac_wol_reset(regs);
+
+	switch (type) {
+	case VELOCITY_INIT_RESET:
+	case VELOCITY_INIT_WOL:
+
+		netif_stop_queue(vptr->dev);
+
+		/*
+		 *	Reset RX to prevent RX pointer not on the 4X location
+		 */
+		velocity_rx_reset(vptr);
+		mac_rx_queue_run(regs);
+		mac_rx_queue_wake(regs);
+
+		mii_status = velocity_get_opt_media_mode(vptr);
+		if (velocity_set_media_mode(vptr, mii_status) != VELOCITY_LINK_CHANGE) {
+			velocity_print_link_status(vptr);
+			if (!(vptr->mii_status & VELOCITY_LINK_FAIL))
+				netif_wake_queue(vptr->dev);
+		}
+
+		enable_flow_control_ability(vptr);
+
+		mac_clear_isr(regs);
+		writel(CR0_STOP, &regs->CR0Clr);
+		writel((CR0_DPOLL | CR0_TXON | CR0_RXON | CR0_STRT), 
+							&regs->CR0Set);
+
+		break;
+
+	case VELOCITY_INIT_COLD:
+	default:
+		/*
+		 *	Do reset
+		 */
+		velocity_soft_reset(vptr);
+		mdelay(5);
+
+		mac_eeprom_reload(regs);
+		for (i = 0; i < 6; i++) {
+			writeb(vptr->dev->dev_addr[i], &(regs->PAR[i]));
+		}
+		/*
+		 *	clear Pre_ACPI bit.
+		 */
+		BYTE_REG_BITS_OFF(CFGA_PACPI, &(regs->CFGA));
+		mac_set_rx_thresh(regs, vptr->options.rx_thresh);
+		mac_set_dma_length(regs, vptr->options.DMA_length);
+
+		writeb(WOLCFG_SAM | WOLCFG_SAB, &regs->WOLCFGSet);
+		/*
+		 *	Back off algorithm use original IEEE standard
+		 */
+		BYTE_REG_BITS_SET(CFGB_OFSET, (CFGB_CRANDOM | CFGB_CAP | CFGB_MBA | CFGB_BAKOPT), &regs->CFGB);
+
+		/*
+		 *	Init CAM filter
+		 */
+		velocity_init_cam_filter(vptr);
+
+		/*
+		 *	Set packet filter: Receive directed and broadcast address
+		 */
+		velocity_set_multi(vptr->dev);
+
+		/*
+		 *	Enable MII auto-polling
+		 */
+		enable_mii_autopoll(regs);
+
+		vptr->int_mask = INT_MASK_DEF;
+
+		writel(cpu_to_le32(vptr->rd_pool_dma), &regs->RDBaseLo);
+		writew(vptr->options.numrx - 1, &regs->RDCSize);
+		mac_rx_queue_run(regs);
+		mac_rx_queue_wake(regs);
+
+		writew(vptr->options.numtx - 1, &regs->TDCSize);
+
+		for (i = 0; i < vptr->num_txq; i++) {
+			writel(cpu_to_le32(vptr->td_pool_dma[i]), &(regs->TDBaseLo[i]));
+			mac_tx_queue_run(regs, i);
+		}
+
+		init_flow_control_register(vptr);
+
+		writel(CR0_STOP, &regs->CR0Clr);
+		writel((CR0_DPOLL | CR0_TXON | CR0_RXON | CR0_STRT), &regs->CR0Set);
+
+		mii_status = velocity_get_opt_media_mode(vptr);
+		netif_stop_queue(vptr->dev);
+
+		mii_init(vptr, mii_status);
+
+		if (velocity_set_media_mode(vptr, mii_status) != VELOCITY_LINK_CHANGE) {
+			velocity_print_link_status(vptr);
+			if (!(vptr->mii_status & VELOCITY_LINK_FAIL))
+				netif_wake_queue(vptr->dev);
+		}
+
+		enable_flow_control_ability(vptr);
+		mac_hw_mibs_init(regs);
+		mac_write_int_mask(vptr->int_mask, regs);
+		mac_clear_isr(regs);
+
+	}
+}
+
+/**
+ *	velocity_soft_reset	-	soft reset
+ *	@vptr: velocity to reset
+ *
+ *	Kick off a soft reset of the velocity adapter and then poll
+ *	until the reset sequence has completed before returning.
+ */
+
+static int velocity_soft_reset(struct velocity_info *vptr)
+{
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+	int i = 0;
+
+	writel(CR0_SFRST, &regs->CR0Set);
+
+	for (i = 0; i < W_MAX_TIMEOUT; i++) {
+		udelay(5);
+		if (!DWORD_REG_BITS_IS_ON(CR0_SFRST, &regs->CR0Set))
+			break;
+	}
+
+	if (i == W_MAX_TIMEOUT) {
+		writel(CR0_FORSRST, &regs->CR0Set);
+		/* FIXME: PCI POSTING */
+		/* delay 2ms */
+		mdelay(2);
+	}
+	return 0;
+}
+
+/**
+ *	velocity_found1		-	set up discovered velocity card
+ *	@pdev: PCI device
+ *	@ent: PCI device table entry that matched
+ *
+ *	Configure a discovered adapter from scratch. Return a negative
+ *	errno error code on failure paths.
+ */
+
+static int __devinit velocity_found1(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+	static int first = 1;
+	struct net_device *dev;
+	int i;
+	struct velocity_info_tbl *info = (struct velocity_info_tbl *) ent->driver_data;
+	struct velocity_info *vptr;
+	struct mac_regs __iomem * regs;
+	int ret = -ENOMEM;
+
+	if (velocity_nics >= MAX_UNITS) {
+		printk(KERN_NOTICE VELOCITY_NAME ": already found %d NICs.\n", 
+				velocity_nics);
+		return -ENODEV;
+	}
+
+	dev = alloc_etherdev(sizeof(struct velocity_info));
+
+	if (dev == NULL) {
+		printk(KERN_ERR VELOCITY_NAME ": allocate net device failed.\n");
+		goto out;
+	}
+	
+	/* Chain it all together */
+	
+	SET_MODULE_OWNER(dev);
+	SET_NETDEV_DEV(dev, &pdev->dev);
+	vptr = dev->priv;
+
+
+	if (first) {
+		printk(KERN_INFO "%s Ver. %s\n", 
+			VELOCITY_FULL_DRV_NAM, VELOCITY_VERSION);
+		printk(KERN_INFO "Copyright (c) 2002, 2003 VIA Networking Technologies, Inc.\n");
+		printk(KERN_INFO "Copyright (c) 2004 Red Hat Inc.\n");
+		first = 0;
+	}
+
+	velocity_init_info(pdev, vptr, info);
+
+	vptr->dev = dev;
+
+	dev->irq = pdev->irq;
+
+	ret = pci_enable_device(pdev);
+	if (ret < 0) 
+		goto err_free_dev;
+
+	ret = velocity_get_pci_info(vptr, pdev);
+	if (ret < 0) {
+		printk(KERN_ERR VELOCITY_NAME ": Failed to find PCI device.\n");
+		goto err_disable;
+	}
+
+	ret = pci_request_regions(pdev, VELOCITY_NAME);
+	if (ret < 0) {
+		printk(KERN_ERR VELOCITY_NAME ": Failed to find PCI device.\n");
+		goto err_disable;
+	}
+
+	regs = ioremap(vptr->memaddr, vptr->io_size);
+	if (regs == NULL) {
+		ret = -EIO;
+		goto err_release_res;
+	}
+
+	vptr->mac_regs = regs;
+
+	mac_wol_reset(regs);
+
+	dev->base_addr = vptr->ioaddr;
+
+	for (i = 0; i < 6; i++)
+		dev->dev_addr[i] = readb(&regs->PAR[i]);
+
+
+	velocity_get_options(&vptr->options, velocity_nics, dev->name);
+
+	/* 
+	 *	Mask out the options cannot be set to the chip
+	 */
+	 
+	vptr->options.flags &= info->flags;
+
+	/*
+	 *	Enable the chip specified capbilities
+	 */
+	 
+	vptr->flags = vptr->options.flags | (info->flags & 0xFF000000UL);
+
+	vptr->wol_opts = vptr->options.wol_opts;
+	vptr->flags |= VELOCITY_FLAGS_WOL_ENABLED;
+
+	vptr->phy_id = MII_GET_PHY_ID(vptr->mac_regs);
+
+	dev->irq = pdev->irq;
+	dev->open = velocity_open;
+	dev->hard_start_xmit = velocity_xmit;
+	dev->stop = velocity_close;
+	dev->get_stats = velocity_get_stats;
+	dev->set_multicast_list = velocity_set_multi;
+	dev->do_ioctl = velocity_ioctl;
+	dev->ethtool_ops = &velocity_ethtool_ops;
+	dev->change_mtu = velocity_change_mtu;
+#ifdef  VELOCITY_ZERO_COPY_SUPPORT
+	dev->features |= NETIF_F_SG;
+#endif
+
+	if (vptr->flags & VELOCITY_FLAGS_TX_CSUM) {
+		dev->features |= NETIF_F_HW_CSUM;
+	}
+
+	ret = register_netdev(dev);
+	if (ret < 0)
+		goto err_iounmap;
+
+	velocity_print_info(vptr);
+	pci_set_drvdata(pdev, dev);
+	
+	/* and leave the chip powered down */
+	
+	pci_set_power_state(pdev, PCI_D3hot);
+#ifdef CONFIG_PM
+	{
+		unsigned long flags;
+
+		spin_lock_irqsave(&velocity_dev_list_lock, flags);
+		list_add(&vptr->list, &velocity_dev_list);
+		spin_unlock_irqrestore(&velocity_dev_list_lock, flags);
+	}
+#endif
+	velocity_nics++;
+out:
+	return ret;
+
+err_iounmap:
+	iounmap(regs);
+err_release_res:
+	pci_release_regions(pdev);
+err_disable:
+	pci_disable_device(pdev);
+err_free_dev:
+	free_netdev(dev);
+	goto out;
+}
+
+/**
+ *	velocity_print_info	-	per driver data
+ *	@vptr: velocity
+ *
+ *	Print per driver data as the kernel driver finds Velocity
+ *	hardware
+ */
+
+static void __devinit velocity_print_info(struct velocity_info *vptr)
+{
+	struct net_device *dev = vptr->dev;
+
+	printk(KERN_INFO "%s: %s\n", dev->name, get_chip_name(vptr->chip_id));
+	printk(KERN_INFO "%s: Ethernet Address: %2.2X:%2.2X:%2.2X:%2.2X:%2.2X:%2.2X\n", 
+		dev->name, 
+		dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2], 
+		dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
+}
+
+/**
+ *	velocity_init_info	-	init private data
+ *	@pdev: PCI device
+ *	@vptr: Velocity info
+ *	@info: Board type
+ *
+ *	Set up the initial velocity_info struct for the device that has been
+ *	discovered.
+ */
+
+static void __devinit velocity_init_info(struct pci_dev *pdev, struct velocity_info *vptr, struct velocity_info_tbl *info)
+{
+	memset(vptr, 0, sizeof(struct velocity_info));
+
+	vptr->pdev = pdev;
+	vptr->chip_id = info->chip_id;
+	vptr->io_size = info->io_size;
+	vptr->num_txq = info->txqueue;
+	vptr->multicast_limit = MCAM_SIZE;
+	spin_lock_init(&vptr->lock);
+	INIT_LIST_HEAD(&vptr->list);
+}
+
+/**
+ *	velocity_get_pci_info	-	retrieve PCI info for device
+ *	@vptr: velocity device
+ *	@pdev: PCI device it matches
+ *
+ *	Retrieve the PCI configuration space data that interests us from
+ *	the kernel PCI layer
+ */
+
+static int __devinit velocity_get_pci_info(struct velocity_info *vptr, struct pci_dev *pdev)
+{
+
+	if(pci_read_config_byte(pdev, PCI_REVISION_ID, &vptr->rev_id) < 0)
+		return -EIO;
+		
+	pci_set_master(pdev);
+
+	vptr->ioaddr = pci_resource_start(pdev, 0);
+	vptr->memaddr = pci_resource_start(pdev, 1);
+	
+	if(!(pci_resource_flags(pdev, 0) & IORESOURCE_IO))
+	{
+		printk(KERN_ERR "%s: region #0 is not an I/O resource, aborting.\n",
+				pci_name(pdev));
+		return -EINVAL;
+	}
+
+	if((pci_resource_flags(pdev, 1) & IORESOURCE_IO))
+	{
+		printk(KERN_ERR "%s: region #1 is an I/O resource, aborting.\n",
+				pci_name(pdev));
+		return -EINVAL;
+	}
+
+	if(pci_resource_len(pdev, 1) < 256)
+	{
+		printk(KERN_ERR "%s: region #1 is too small.\n", 
+				pci_name(pdev));
+		return -EINVAL;
+	}
+	vptr->pdev = pdev;
+
+	return 0;
+}
+
+/**
+ *	velocity_init_rings	-	set up DMA rings
+ *	@vptr: Velocity to set up
+ *
+ *	Allocate PCI mapped DMA rings for the receive and transmit layer
+ *	to use.
+ */
+
+static int velocity_init_rings(struct velocity_info *vptr)
+{
+	int i;
+	unsigned int psize;
+	unsigned int tsize;
+	dma_addr_t pool_dma;
+	u8 *pool;
+
+	/*
+	 *	Allocate all RD/TD rings a single pool 
+	 */
+	 
+	psize = vptr->options.numrx * sizeof(struct rx_desc) + 
+		vptr->options.numtx * sizeof(struct tx_desc) * vptr->num_txq;
+
+	/*
+	 * pci_alloc_consistent() fulfills the requirement for 64 bytes
+	 * alignment
+	 */
+	pool = pci_alloc_consistent(vptr->pdev, psize, &pool_dma);
+
+	if (pool == NULL) {
+		printk(KERN_ERR "%s : DMA memory allocation failed.\n", 
+					vptr->dev->name);
+		return -ENOMEM;
+	}
+
+	memset(pool, 0, psize);
+
+	vptr->rd_ring = (struct rx_desc *) pool;
+
+	vptr->rd_pool_dma = pool_dma;
+
+	tsize = vptr->options.numtx * PKT_BUF_SZ * vptr->num_txq;
+	vptr->tx_bufs = pci_alloc_consistent(vptr->pdev, tsize, 
+						&vptr->tx_bufs_dma);
+
+	if (vptr->tx_bufs == NULL) {
+		printk(KERN_ERR "%s: DMA memory allocation failed.\n", 
+					vptr->dev->name);
+		pci_free_consistent(vptr->pdev, psize, pool, pool_dma);
+		return -ENOMEM;
+	}
+
+	memset(vptr->tx_bufs, 0, vptr->options.numtx * PKT_BUF_SZ * vptr->num_txq);
+
+	i = vptr->options.numrx * sizeof(struct rx_desc);
+	pool += i;
+	pool_dma += i;
+	for (i = 0; i < vptr->num_txq; i++) {
+		int offset = vptr->options.numtx * sizeof(struct tx_desc);
+
+		vptr->td_pool_dma[i] = pool_dma;
+		vptr->td_rings[i] = (struct tx_desc *) pool;
+		pool += offset;
+		pool_dma += offset;
+	}
+	return 0;
+}
+
+/**
+ *	velocity_free_rings	-	free PCI ring pointers
+ *	@vptr: Velocity to free from
+ *
+ *	Clean up the PCI ring buffers allocated to this velocity.
+ */
+
+static void velocity_free_rings(struct velocity_info *vptr)
+{
+	int size;
+
+	size = vptr->options.numrx * sizeof(struct rx_desc) + 
+	       vptr->options.numtx * sizeof(struct tx_desc) * vptr->num_txq;
+
+	pci_free_consistent(vptr->pdev, size, vptr->rd_ring, vptr->rd_pool_dma);
+
+	size = vptr->options.numtx * PKT_BUF_SZ * vptr->num_txq;
+
+	pci_free_consistent(vptr->pdev, size, vptr->tx_bufs, vptr->tx_bufs_dma);
+}
+
+static inline void velocity_give_many_rx_descs(struct velocity_info *vptr)
+{
+	struct mac_regs __iomem *regs = vptr->mac_regs;
+	int avail, dirty, unusable;
+
+	/*
+	 * RD number must be equal to 4X per hardware spec
+	 * (programming guide rev 1.20, p.13)
+	 */
+	if (vptr->rd_filled < 4)
+		return;
+
+	wmb();
+
+	unusable = vptr->rd_filled & 0x0003;
+	dirty = vptr->rd_dirty - unusable;
+	for (avail = vptr->rd_filled & 0xfffc; avail; avail--) {
+		dirty = (dirty > 0) ? dirty - 1 : vptr->options.numrx - 1;
+		vptr->rd_ring[dirty].rdesc0.owner = OWNED_BY_NIC;
+	}
+
+	writew(vptr->rd_filled & 0xfffc, &regs->RBRDU);
+	vptr->rd_filled = unusable;
+}
+
+static int velocity_rx_refill(struct velocity_info *vptr)
+{
+	int dirty = vptr->rd_dirty, done = 0, ret = 0;
+
+	do {
+		struct rx_desc *rd = vptr->rd_ring + dirty;
+
+		/* Fine for an all zero Rx desc at init time as well */
+		if (rd->rdesc0.owner == OWNED_BY_NIC)
+			break;
+
+		if (!vptr->rd_info[dirty].skb) {
+			ret = velocity_alloc_rx_buf(vptr, dirty);
+			if (ret < 0)
+				break;
+		}
+		done++;
+		dirty = (dirty < vptr->options.numrx - 1) ? dirty + 1 : 0;	
+	} while (dirty != vptr->rd_curr);
+
+	if (done) {
+		vptr->rd_dirty = dirty;
+		vptr->rd_filled += done;
+		velocity_give_many_rx_descs(vptr);
+	}
+
+	return ret;
+}
+
+/**
+ *	velocity_init_rd_ring	-	set up receive ring
+ *	@vptr: velocity to configure
+ *
+ *	Allocate and set up the receive buffers for each ring slot and
+ *	assign them to the network adapter.
+ */
+
+static int velocity_init_rd_ring(struct velocity_info *vptr)
+{
+	int ret = -ENOMEM;
+	unsigned int rsize = sizeof(struct velocity_rd_info) * 
+					vptr->options.numrx;
+
+	vptr->rd_info = kmalloc(rsize, GFP_KERNEL);
+	if(vptr->rd_info == NULL)
+		goto out;
+	memset(vptr->rd_info, 0, rsize);
+
+	vptr->rd_filled = vptr->rd_dirty = vptr->rd_curr = 0;
+
+	ret = velocity_rx_refill(vptr);
+	if (ret < 0) {
+		VELOCITY_PRT(MSG_LEVEL_ERR, KERN_ERR
+			"%s: failed to allocate RX buffer.\n", vptr->dev->name);
+		velocity_free_rd_ring(vptr);
+	}
+out:
+	return ret;
+}
+
+/**
+ *	velocity_free_rd_ring	-	free receive ring
+ *	@vptr: velocity to clean up
+ *
+ *	Free the receive buffers for each ring slot and any
+ *	attached socket buffers that need to go away.
+ */
+
+static void velocity_free_rd_ring(struct velocity_info *vptr)
+{
+	int i;
+
+	if (vptr->rd_info == NULL)
+		return;
+
+	for (i = 0; i < vptr->options.numrx; i++) {
+		struct velocity_rd_info *rd_info = &(vptr->rd_info[i]);
+
+		if (!rd_info->skb)
+			continue;
+		pci_unmap_single(vptr->pdev, rd_info->skb_dma, vptr->rx_buf_sz,
+				 PCI_DMA_FROMDEVICE);
+		rd_info->skb_dma = (dma_addr_t) NULL;
+
+		dev_kfree_skb(rd_info->skb);
+		rd_info->skb = NULL;
+	}
+
+	kfree(vptr->rd_info);
+	vptr->rd_info = NULL;
+}
+
+/**
+ *	velocity_init_td_ring	-	set up transmit ring
+ *	@vptr:	velocity
+ *
+ *	Set up the transmit ring and chain the ring pointers together.
+ *	Returns zero on success or a negative posix errno code for
+ *	failure.
+ */
+ 
+static int velocity_init_td_ring(struct velocity_info *vptr)
+{
+	int i, j;
+	dma_addr_t curr;
+	struct tx_desc *td;
+	struct velocity_td_info *td_info;
+	unsigned int tsize = sizeof(struct velocity_td_info) * 
+					vptr->options.numtx;
+
+	/* Init the TD ring entries */
+	for (j = 0; j < vptr->num_txq; j++) {
+		curr = vptr->td_pool_dma[j];
+
+		vptr->td_infos[j] = kmalloc(tsize, GFP_KERNEL);
+		if(vptr->td_infos[j] == NULL)
+		{
+			while(--j >= 0)
+				kfree(vptr->td_infos[j]);
+			return -ENOMEM;
+		}
+		memset(vptr->td_infos[j], 0, tsize);
+
+		for (i = 0; i < vptr->options.numtx; i++, curr += sizeof(struct tx_desc)) {
+			td = &(vptr->td_rings[j][i]);
+			td_info = &(vptr->td_infos[j][i]);
+			td_info->buf = vptr->tx_bufs +
+				(j * vptr->options.numtx + i) * PKT_BUF_SZ;
+			td_info->buf_dma = vptr->tx_bufs_dma +
+				(j * vptr->options.numtx + i) * PKT_BUF_SZ;
+		}
+		vptr->td_tail[j] = vptr->td_curr[j] = vptr->td_used[j] = 0;
+	}
+	return 0;
+}
+
+/*
+ *	FIXME: could we merge this with velocity_free_tx_buf ?
+ */
+
+static void velocity_free_td_ring_entry(struct velocity_info *vptr,
+							 int q, int n)
+{
+	struct velocity_td_info * td_info = &(vptr->td_infos[q][n]);
+	int i;
+	
+	if (td_info == NULL)
+		return;
+		
+	if (td_info->skb) {
+		for (i = 0; i < td_info->nskb_dma; i++)
+		{
+			if (td_info->skb_dma[i]) {
+				pci_unmap_single(vptr->pdev, td_info->skb_dma[i], 
+					td_info->skb->len, PCI_DMA_TODEVICE);
+				td_info->skb_dma[i] = (dma_addr_t) NULL;
+			}
+		}
+		dev_kfree_skb(td_info->skb);
+		td_info->skb = NULL;
+	}
+}
+
+/**
+ *	velocity_free_td_ring	-	free td ring
+ *	@vptr: velocity
+ *
+ *	Free up the transmit ring for this particular velocity adapter.
+ *	We free the ring contents but not the ring itself.
+ */
+ 
+static void velocity_free_td_ring(struct velocity_info *vptr)
+{
+	int i, j;
+
+	for (j = 0; j < vptr->num_txq; j++) {
+		if (vptr->td_infos[j] == NULL)
+			continue;
+		for (i = 0; i < vptr->options.numtx; i++) {
+			velocity_free_td_ring_entry(vptr, j, i);
+
+		}
+		if (vptr->td_infos[j]) {
+			kfree(vptr->td_infos[j]);
+			vptr->td_infos[j] = NULL;
+		}
+	}
+}
+
+/**
+ *	velocity_rx_srv		-	service RX interrupt
+ *	@vptr: velocity
+ *	@status: adapter status (unused)
+ *
+ *	Walk the receive ring of the velocity adapter and remove
+ *	any received packets from the receive queue. Hand the ring
+ *	slots back to the adapter for reuse.
+ */
+ 
+static int velocity_rx_srv(struct velocity_info *vptr, int status)
+{
+	struct net_device_stats *stats = &vptr->stats;
+	int rd_curr = vptr->rd_curr;
+	int works = 0;
+
+	do {
+		struct rx_desc *rd = vptr->rd_ring + rd_curr;
+
+		if (!vptr->rd_info[rd_curr].skb)
+			break;
+
+		if (rd->rdesc0.owner == OWNED_BY_NIC)
+			break;
+
+		rmb();
+
+		/*
+		 *	Don't drop CE or RL error frame although RXOK is off
+		 */
+		if ((rd->rdesc0.RSR & RSR_RXOK) || (!(rd->rdesc0.RSR & RSR_RXOK) && (rd->rdesc0.RSR & (RSR_CE | RSR_RL)))) {
+			if (velocity_receive_frame(vptr, rd_curr) < 0)
+				stats->rx_dropped++;
+		} else {
+			if (rd->rdesc0.RSR & RSR_CRC)
+				stats->rx_crc_errors++;
+			if (rd->rdesc0.RSR & RSR_FAE)
+				stats->rx_frame_errors++;
+
+			stats->rx_dropped++;
+		}
+
+		rd->inten = 1;
+
+		vptr->dev->last_rx = jiffies;
+
+		rd_curr++;
+		if (rd_curr >= vptr->options.numrx)
+			rd_curr = 0;
+	} while (++works <= 15);
+
+	vptr->rd_curr = rd_curr;
+
+	if (works > 0 && velocity_rx_refill(vptr) < 0) {
+		VELOCITY_PRT(MSG_LEVEL_ERR, KERN_ERR
+			"%s: rx buf allocation failure\n", vptr->dev->name);
+	}
+
+	VAR_USED(stats);
+	return works;
+}
+
+/**
+ *	velocity_rx_csum	-	checksum process
+ *	@rd: receive packet descriptor
+ *	@skb: network layer packet buffer
+ *
+ *	Process the status bits for the received packet and determine
+ *	if the checksum was computed and verified by the hardware
+ */
+ 
+static inline void velocity_rx_csum(struct rx_desc *rd, struct sk_buff *skb)
+{
+	skb->ip_summed = CHECKSUM_NONE;
+
+	if (rd->rdesc1.CSM & CSM_IPKT) {
+		if (rd->rdesc1.CSM & CSM_IPOK) {
+			if ((rd->rdesc1.CSM & CSM_TCPKT) || 
+					(rd->rdesc1.CSM & CSM_UDPKT)) {
+				if (!(rd->rdesc1.CSM & CSM_TUPOK)) {
+					return;
+				}
+			}
+			skb->ip_summed = CHECKSUM_UNNECESSARY;
+		}
+	}
+}
+
+/**
+ *	velocity_rx_copy	-	in place Rx copy for small packets
+ *	@rx_skb: network layer packet buffer candidate
+ *	@pkt_size: received data size
+ *	@rd: receive packet descriptor
+ *	@dev: network device
+ *
+ *	Replace the current skb that is scheduled for Rx processing by a
+ *	shorter, immediatly allocated skb, if the received packet is small
+ *	enough. This function returns a negative value if the received
+ *	packet is too big or if memory is exhausted.
+ */
+static inline int velocity_rx_copy(struct sk_buff **rx_skb, int pkt_size,
+				   struct velocity_info *vptr)
+{
+	int ret = -1;
+
+	if (pkt_size < rx_copybreak) {
+		struct sk_buff *new_skb;
+
+		new_skb = dev_alloc_skb(pkt_size + 2);
+		if (new_skb) {
+			new_skb->dev = vptr->dev;
+			new_skb->ip_summed = rx_skb[0]->ip_summed;
+
+			if (vptr->flags & VELOCITY_FLAGS_IP_ALIGN)
+				skb_reserve(new_skb, 2);
+
+			memcpy(new_skb->data, rx_skb[0]->tail, pkt_size);
+			*rx_skb = new_skb;
+			ret = 0;
+		}
+		
+	}
+	return ret;
+}
+
+/**
+ *	velocity_iph_realign	-	IP header alignment
+ *	@vptr: velocity we are handling
+ *	@skb: network layer packet buffer
+ *	@pkt_size: received data size
+ *
+ *	Align IP header on a 2 bytes boundary. This behavior can be
+ *	configured by the user.
+ */
+static inline void velocity_iph_realign(struct velocity_info *vptr,
+					struct sk_buff *skb, int pkt_size)
+{
+	/* FIXME - memmove ? */
+	if (vptr->flags & VELOCITY_FLAGS_IP_ALIGN) {
+		int i;
+
+		for (i = pkt_size; i >= 0; i--)
+			*(skb->data + i + 2) = *(skb->data + i);
+		skb_reserve(skb, 2);
+	}
+}
+
+/**
+ *	velocity_receive_frame	-	received packet processor
+ *	@vptr: velocity we are handling
+ *	@idx: ring index
+ *	
+ *	A packet has arrived. We process the packet and if appropriate
+ *	pass the frame up the network stack
+ */
+ 
+static int velocity_receive_frame(struct velocity_info *vptr, int idx)
+{
+	void (*pci_action)(struct pci_dev *, dma_addr_t, size_t, int);
+	struct net_device_stats *stats = &vptr->stats;
+	struct velocity_rd_info *rd_info = &(vptr->rd_info[idx]);
+	struct rx_desc *rd = &(vptr->rd_ring[idx]);
+	int pkt_len = rd->rdesc0.len;
+	struct sk_buff *skb;
+
+	if (rd->rdesc0.RSR & (RSR_STP | RSR_EDP)) {
+		VELOCITY_PRT(MSG_LEVEL_VERBOSE, KERN_ERR " %s : the received frame span multple RDs.\n", vptr->dev->name);
+		stats->rx_length_errors++;
+		return -EINVAL;
+	}
+
+	if (rd->rdesc0.RSR & RSR_MAR)
+		vptr->stats.multicast++;
+
+	skb = rd_info->skb;
+	skb->dev = vptr->dev;
+
+	pci_dma_sync_single_for_cpu(vptr->pdev, rd_info->skb_dma,
+				    vptr->rx_buf_sz, PCI_DMA_FROMDEVICE);
+
+	/*
+	 *	Drop frame not meeting IEEE 802.3
+	 */
+	 
+	if (vptr->flags & VELOCITY_FLAGS_VAL_PKT_LEN) {
+		if (rd->rdesc0.RSR & RSR_RL) {
+			stats->rx_length_errors++;
+			return -EINVAL;
+		}
+	}
+
+	pci_action = pci_dma_sync_single_for_device;
+
+	velocity_rx_csum(rd, skb);
+
+	if (velocity_rx_copy(&skb, pkt_len, vptr) < 0) {
+		velocity_iph_realign(vptr, skb, pkt_len);
+		pci_action = pci_unmap_single;
+		rd_info->skb = NULL;
+	}
+
+	pci_action(vptr->pdev, rd_info->skb_dma, vptr->rx_buf_sz,
+		   PCI_DMA_FROMDEVICE);
+
+	skb_put(skb, pkt_len - 4);
+	skb->protocol = eth_type_trans(skb, skb->dev);	
+
+	stats->rx_bytes += pkt_len;
+	netif_rx(skb);
+
+	return 0;
+}
+
+/**
+ *	velocity_alloc_rx_buf	-	allocate aligned receive buffer
+ *	@vptr: velocity
+ *	@idx: ring index
+ *
+ *	Allocate a new full sized buffer for the reception of a frame and
+ *	map it into PCI space for the hardware to use. The hardware
+ *	requires *64* byte alignment of the buffer which makes life
+ *	less fun than would be ideal.
+ */
+ 
+static int velocity_alloc_rx_buf(struct velocity_info *vptr, int idx)
+{
+	struct rx_desc *rd = &(vptr->rd_ring[idx]);
+	struct velocity_rd_info *rd_info = &(vptr->rd_info[idx]);
+
+	rd_info->skb = dev_alloc_skb(vptr->rx_buf_sz + 64);
+	if (rd_info->skb == NULL)
+		return -ENOMEM;
+
+	/*
+	 *	Do the gymnastics to get the buffer head for data at
+	 *	64byte alignment.
+	 */
+	skb_reserve(rd_info->skb, (unsigned long) rd_info->skb->tail & 63);
+	rd_info->skb->dev = vptr->dev;
+	rd_info->skb_dma = pci_map_single(vptr->pdev, rd_info->skb->tail, vptr->rx_buf_sz, PCI_DMA_FROMDEVICE);
+	
+	/*
+	 *	Fill in the descriptor to match
+ 	 */	
+ 	 
+	*((u32 *) & (rd->rdesc0)) = 0;
+	rd->len = cpu_to_le32(vptr->rx_buf_sz);
+	rd->inten = 1;
+	rd->pa_low = cpu_to_le32(rd_info->skb_dma);
+	rd->pa_high = 0;
+	return 0;
+}
+
+/**
+ *	tx_srv		-	transmit interrupt service
+ *	@vptr; Velocity
+ *	@status:
+ *
+ *	Scan the queues looking for transmitted packets that
+ *	we can complete and clean up. Update any statistics as
+ *	neccessary/
+ */
+ 
+static int velocity_tx_srv(struct velocity_info *vptr, u32 status)
+{
+	struct tx_desc *td;
+	int qnum;
+	int full = 0;
+	int idx;
+	int works = 0;
+	struct velocity_td_info *tdinfo;
+	struct net_device_stats *stats = &vptr->stats;
+
+	for (qnum = 0; qnum < vptr->num_txq; qnum++) {
+		for (idx = vptr->td_tail[qnum]; vptr->td_used[qnum] > 0; 
+			idx = (idx + 1) % vptr->options.numtx) {
+
+			/*
+			 *	Get Tx Descriptor
+			 */
+			td = &(vptr->td_rings[qnum][idx]);
+			tdinfo = &(vptr->td_infos[qnum][idx]);
+
+			if (td->tdesc0.owner == OWNED_BY_NIC)
+				break;
+
+			if ((works++ > 15))
+				break;
+
+			if (td->tdesc0.TSR & TSR0_TERR) {
+				stats->tx_errors++;
+				stats->tx_dropped++;
+				if (td->tdesc0.TSR & TSR0_CDH)
+					stats->tx_heartbeat_errors++;
+				if (td->tdesc0.TSR & TSR0_CRS)
+					stats->tx_carrier_errors++;
+				if (td->tdesc0.TSR & TSR0_ABT)
+					stats->tx_aborted_errors++;
+				if (td->tdesc0.TSR & TSR0_OWC)
+					stats->tx_window_errors++;
+			} else {
+				stats->tx_packets++;
+				stats->tx_bytes += tdinfo->skb->len;
+			}
+			velocity_free_tx_buf(vptr, tdinfo);
+			vptr->td_used[qnum]--;
+		}
+		vptr->td_tail[qnum] = idx;
+
+		if (AVAIL_TD(vptr, qnum) < 1) {
+			full = 1;
+		}
+	}
+	/*
+	 *	Look to see if we should kick the transmit network
+	 *	layer for more work.
+	 */
+	if (netif_queue_stopped(vptr->dev) && (full == 0)
+	    && (!(vptr->mii_status & VELOCITY_LINK_FAIL))) {
+		netif_wake_queue(vptr->dev);
+	}
+	return works;
+}
+
+/**
+ *	velocity_print_link_status	-	link status reporting
+ *	@vptr: velocity to report on
+ *
+ *	Turn the link status of the velocity card into a kernel log
+ *	description of the new link state, detailing speed and duplex
+ *	status
+ */
+
+static void velocity_print_link_status(struct velocity_info *vptr)
+{
+
+	if (vptr->mii_status & VELOCITY_LINK_FAIL) {
+		VELOCITY_PRT(MSG_LEVEL_INFO, KERN_NOTICE "%s: failed to detect cable link\n", vptr->dev->name);
+	} else if (vptr->options.spd_dpx == SPD_DPX_AUTO) {
+		VELOCITY_PRT(MSG_LEVEL_INFO, KERN_NOTICE "%s: Link autonegation", vptr->dev->name);
+
+		if (vptr->mii_status & VELOCITY_SPEED_1000)
+			VELOCITY_PRT(MSG_LEVEL_INFO, " speed 1000M bps");
+		else if (vptr->mii_status & VELOCITY_SPEED_100)
+			VELOCITY_PRT(MSG_LEVEL_INFO, " speed 100M bps");
+		else
+			VELOCITY_PRT(MSG_LEVEL_INFO, " speed 10M bps");
+
+		if (vptr->mii_status & VELOCITY_DUPLEX_FULL)
+			VELOCITY_PRT(MSG_LEVEL_INFO, " full duplex\n");
+		else
+			VELOCITY_PRT(MSG_LEVEL_INFO, " half duplex\n");
+	} else {
+		VELOCITY_PRT(MSG_LEVEL_INFO, KERN_NOTICE "%s: Link forced", vptr->dev->name);
+		switch (vptr->options.spd_dpx) {
+		case SPD_DPX_100_HALF:
+			VELOCITY_PRT(MSG_LEVEL_INFO, " speed 100M bps half duplex\n");
+			break;
+		case SPD_DPX_100_FULL:
+			VELOCITY_PRT(MSG_LEVEL_INFO, " speed 100M bps full duplex\n");
+			break;
+		case SPD_DPX_10_HALF:
+			VELOCITY_PRT(MSG_LEVEL_INFO, " speed 10M bps half duplex\n");
+			break;
+		case SPD_DPX_10_FULL:
+			VELOCITY_PRT(MSG_LEVEL_INFO, " speed 10M bps full duplex\n");
+			break;
+		default:
+			break;
+		}
+	}
+}
+
+/**
+ *	velocity_error	-	handle error from controller
+ *	@vptr: velocity
+ *	@status: card status
+ *
+ *	Process an error report from the hardware and attempt to recover
+ *	the card itself. At the moment we cannot recover from some 
+ *	theoretically impossible errors but this could be fixed using
+ *	the pci_device_failed logic to bounce the hardware
+ *
+ */
+ 
+static void velocity_error(struct velocity_info *vptr, int status)
+{
+
+	if (status & ISR_TXSTLI) {
+		struct mac_regs __iomem * regs = vptr->mac_regs;
+
+		printk(KERN_ERR "TD structure errror TDindex=%hx\n", readw(&regs->TDIdx[0]));
+		BYTE_REG_BITS_ON(TXESR_TDSTR, &regs->TXESR);
+		writew(TRDCSR_RUN, &regs->TDCSRClr);
+		netif_stop_queue(vptr->dev);
+		
+		/* FIXME: port over the pci_device_failed code and use it
+		   here */
+	}
+
+	if (status & ISR_SRCI) {
+		struct mac_regs __iomem * regs = vptr->mac_regs;
+		int linked;
+
+		if (vptr->options.spd_dpx == SPD_DPX_AUTO) {
+			vptr->mii_status = check_connection_type(regs);
+
+			/*
+			 *	If it is a 3119, disable frame bursting in 
+			 *	halfduplex mode and enable it in fullduplex
+			 *	 mode
+			 */
+			if (vptr->rev_id < REV_ID_VT3216_A0) {
+				if (vptr->mii_status | VELOCITY_DUPLEX_FULL)
+					BYTE_REG_BITS_ON(TCR_TB2BDIS, &regs->TCR);
+				else
+					BYTE_REG_BITS_OFF(TCR_TB2BDIS, &regs->TCR);
+			}
+			/*
+			 *	Only enable CD heart beat counter in 10HD mode
+			 */
+			if (!(vptr->mii_status & VELOCITY_DUPLEX_FULL) && (vptr->mii_status & VELOCITY_SPEED_10)) {
+				BYTE_REG_BITS_OFF(TESTCFG_HBDIS, &regs->TESTCFG);
+			} else {
+				BYTE_REG_BITS_ON(TESTCFG_HBDIS, &regs->TESTCFG);
+			}
+		}
+		/*
+		 *	Get link status from PHYSR0
+		 */
+		linked = readb(&regs->PHYSR0) & PHYSR0_LINKGD;
+
+		if (linked) {
+			vptr->mii_status &= ~VELOCITY_LINK_FAIL;
+		} else {
+			vptr->mii_status |= VELOCITY_LINK_FAIL;
+		}
+
+		velocity_print_link_status(vptr);
+		enable_flow_control_ability(vptr);
+
+		/*
+		 *	Re-enable auto-polling because SRCI will disable 
+		 *	auto-polling
+		 */
+		 
+		enable_mii_autopoll(regs);
+
+		if (vptr->mii_status & VELOCITY_LINK_FAIL)
+			netif_stop_queue(vptr->dev);
+		else
+			netif_wake_queue(vptr->dev);
+
+	};
+	if (status & ISR_MIBFI)
+		velocity_update_hw_mibs(vptr);
+	if (status & ISR_LSTEI)
+		mac_rx_queue_wake(vptr->mac_regs);
+}
+
+/**
+ *	velocity_free_tx_buf	-	free transmit buffer
+ *	@vptr: velocity
+ *	@tdinfo: buffer
+ *
+ *	Release an transmit buffer. If the buffer was preallocated then
+ *	recycle it, if not then unmap the buffer.
+ */
+ 
+static void velocity_free_tx_buf(struct velocity_info *vptr, struct velocity_td_info *tdinfo)
+{
+	struct sk_buff *skb = tdinfo->skb;
+	int i;
+
+	/*
+	 *	Don't unmap the pre-allocated tx_bufs
+	 */
+	if (tdinfo->skb_dma && (tdinfo->skb_dma[0] != tdinfo->buf_dma)) {
+
+		for (i = 0; i < tdinfo->nskb_dma; i++) {
+#ifdef VELOCITY_ZERO_COPY_SUPPORT
+			pci_unmap_single(vptr->pdev, tdinfo->skb_dma[i], td->tdesc1.len, PCI_DMA_TODEVICE);
+#else
+			pci_unmap_single(vptr->pdev, tdinfo->skb_dma[i], skb->len, PCI_DMA_TODEVICE);
+#endif
+			tdinfo->skb_dma[i] = 0;
+		}
+	}
+	dev_kfree_skb_irq(skb);
+	tdinfo->skb = NULL;
+}
+
+/**
+ *	velocity_open		-	interface activation callback
+ *	@dev: network layer device to open
+ *
+ *	Called when the network layer brings the interface up. Returns
+ *	a negative posix error code on failure, or zero on success.
+ *
+ *	All the ring allocation and set up is done on open for this
+ *	adapter to minimise memory usage when inactive
+ */
+ 
+static int velocity_open(struct net_device *dev)
+{
+	struct velocity_info *vptr = dev->priv;
+	int ret;
+
+	vptr->rx_buf_sz = (dev->mtu <= 1504 ? PKT_BUF_SZ : dev->mtu + 32);
+
+	ret = velocity_init_rings(vptr);
+	if (ret < 0)
+		goto out;
+
+	ret = velocity_init_rd_ring(vptr);
+	if (ret < 0)
+		goto err_free_desc_rings;
+
+	ret = velocity_init_td_ring(vptr);
+	if (ret < 0)
+		goto err_free_rd_ring;
+	
+	/* Ensure chip is running */	
+	pci_set_power_state(vptr->pdev, PCI_D0);
+	
+	velocity_init_registers(vptr, VELOCITY_INIT_COLD);
+
+	ret = request_irq(vptr->pdev->irq, &velocity_intr, SA_SHIRQ,
+			  dev->name, dev);
+	if (ret < 0) {
+		/* Power down the chip */
+		pci_set_power_state(vptr->pdev, PCI_D3hot);
+		goto err_free_td_ring;
+	}
+
+	mac_enable_int(vptr->mac_regs);
+	netif_start_queue(dev);
+	vptr->flags |= VELOCITY_FLAGS_OPENED;
+out:
+	return ret;
+
+err_free_td_ring:
+	velocity_free_td_ring(vptr);
+err_free_rd_ring:
+	velocity_free_rd_ring(vptr);
+err_free_desc_rings:
+	velocity_free_rings(vptr);
+	goto out;
+}
+
+/** 
+ *	velocity_change_mtu	-	MTU change callback
+ *	@dev: network device
+ *	@new_mtu: desired MTU
+ *
+ *	Handle requests from the networking layer for MTU change on
+ *	this interface. It gets called on a change by the network layer.
+ *	Return zero for success or negative posix error code.
+ */
+ 
+static int velocity_change_mtu(struct net_device *dev, int new_mtu)
+{
+	struct velocity_info *vptr = dev->priv;
+	unsigned long flags;
+	int oldmtu = dev->mtu;
+	int ret = 0;
+
+	if ((new_mtu < VELOCITY_MIN_MTU) || new_mtu > (VELOCITY_MAX_MTU)) {
+		VELOCITY_PRT(MSG_LEVEL_ERR, KERN_NOTICE "%s: Invalid MTU.\n", 
+				vptr->dev->name);
+		return -EINVAL;
+	}
+
+	if (new_mtu != oldmtu) {
+		spin_lock_irqsave(&vptr->lock, flags);
+
+		netif_stop_queue(dev);
+		velocity_shutdown(vptr);
+
+		velocity_free_td_ring(vptr);
+		velocity_free_rd_ring(vptr);
+
+		dev->mtu = new_mtu;
+		if (new_mtu > 8192)
+			vptr->rx_buf_sz = 9 * 1024;
+		else if (new_mtu > 4096)
+			vptr->rx_buf_sz = 8192;
+		else
+			vptr->rx_buf_sz = 4 * 1024;
+
+		ret = velocity_init_rd_ring(vptr);
+		if (ret < 0)
+			goto out_unlock;
+
+		ret = velocity_init_td_ring(vptr);
+		if (ret < 0)
+			goto out_unlock;
+
+		velocity_init_registers(vptr, VELOCITY_INIT_COLD);
+
+		mac_enable_int(vptr->mac_regs);
+		netif_start_queue(dev);
+out_unlock:
+		spin_unlock_irqrestore(&vptr->lock, flags);
+	}
+
+	return ret;
+}
+
+/**
+ *	velocity_shutdown	-	shut down the chip
+ *	@vptr: velocity to deactivate
+ *
+ *	Shuts down the internal operations of the velocity and
+ *	disables interrupts, autopolling, transmit and receive
+ */
+ 
+static void velocity_shutdown(struct velocity_info *vptr)
+{
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+	mac_disable_int(regs);
+	writel(CR0_STOP, &regs->CR0Set);
+	writew(0xFFFF, &regs->TDCSRClr);
+	writeb(0xFF, &regs->RDCSRClr);
+	safe_disable_mii_autopoll(regs);
+	mac_clear_isr(regs);
+}
+
+/**
+ *	velocity_close		-	close adapter callback
+ *	@dev: network device
+ *
+ *	Callback from the network layer when the velocity is being
+ *	deactivated by the network layer
+ */
+
+static int velocity_close(struct net_device *dev)
+{
+	struct velocity_info *vptr = dev->priv;
+
+	netif_stop_queue(dev);
+	velocity_shutdown(vptr);
+
+	if (vptr->flags & VELOCITY_FLAGS_WOL_ENABLED)
+		velocity_get_ip(vptr);
+	if (dev->irq != 0)
+		free_irq(dev->irq, dev);
+		
+	/* Power down the chip */
+	pci_set_power_state(vptr->pdev, PCI_D3hot);
+	
+	/* Free the resources */
+	velocity_free_td_ring(vptr);
+	velocity_free_rd_ring(vptr);
+	velocity_free_rings(vptr);
+
+	vptr->flags &= (~VELOCITY_FLAGS_OPENED);
+	return 0;
+}
+
+/**
+ *	velocity_xmit		-	transmit packet callback
+ *	@skb: buffer to transmit
+ *	@dev: network device
+ *
+ *	Called by the networ layer to request a packet is queued to
+ *	the velocity. Returns zero on success.
+ */
+ 
+static int velocity_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+	struct velocity_info *vptr = dev->priv;
+	int qnum = 0;
+	struct tx_desc *td_ptr;
+	struct velocity_td_info *tdinfo;
+	unsigned long flags;
+	int index;
+
+	int pktlen = skb->len;
+
+	spin_lock_irqsave(&vptr->lock, flags);
+
+	index = vptr->td_curr[qnum];
+	td_ptr = &(vptr->td_rings[qnum][index]);
+	tdinfo = &(vptr->td_infos[qnum][index]);
+
+	td_ptr->tdesc1.TCPLS = TCPLS_NORMAL;
+	td_ptr->tdesc1.TCR = TCR0_TIC;
+	td_ptr->td_buf[0].queue = 0;
+
+	/*
+	 *	Pad short frames. 
+	 */
+	if (pktlen < ETH_ZLEN) {
+		/* Cannot occur until ZC support */
+		if(skb_linearize(skb, GFP_ATOMIC))
+			return 0; 
+		pktlen = ETH_ZLEN;
+		memcpy(tdinfo->buf, skb->data, skb->len);
+		memset(tdinfo->buf + skb->len, 0, ETH_ZLEN - skb->len);
+		tdinfo->skb = skb;
+		tdinfo->skb_dma[0] = tdinfo->buf_dma;
+		td_ptr->tdesc0.pktsize = pktlen;
+		td_ptr->td_buf[0].pa_low = cpu_to_le32(tdinfo->skb_dma[0]);
+		td_ptr->td_buf[0].pa_high = 0;
+		td_ptr->td_buf[0].bufsize = td_ptr->tdesc0.pktsize;
+		tdinfo->nskb_dma = 1;
+		td_ptr->tdesc1.CMDZ = 2;
+	} else
+#ifdef VELOCITY_ZERO_COPY_SUPPORT
+	if (skb_shinfo(skb)->nr_frags > 0) {
+		int nfrags = skb_shinfo(skb)->nr_frags;
+		tdinfo->skb = skb;
+		if (nfrags > 6) {
+			skb_linearize(skb, GFP_ATOMIC);
+			memcpy(tdinfo->buf, skb->data, skb->len);
+			tdinfo->skb_dma[0] = tdinfo->buf_dma;
+			td_ptr->tdesc0.pktsize = 
+			td_ptr->td_buf[0].pa_low = cpu_to_le32(tdinfo->skb_dma[0]);
+			td_ptr->td_buf[0].pa_high = 0;
+			td_ptr->td_buf[0].bufsize = td_ptr->tdesc0.pktsize;
+			tdinfo->nskb_dma = 1;
+			td_ptr->tdesc1.CMDZ = 2;
+		} else {
+			int i = 0;
+			tdinfo->nskb_dma = 0;
+			tdinfo->skb_dma[i] = pci_map_single(vptr->pdev, skb->data, skb->len - skb->data_len, PCI_DMA_TODEVICE);
+
+			td_ptr->tdesc0.pktsize = pktlen;
+
+			/* FIXME: support 48bit DMA later */
+			td_ptr->td_buf[i].pa_low = cpu_to_le32(tdinfo->skb_dma);
+			td_ptr->td_buf[i].pa_high = 0;
+			td_ptr->td_buf[i].bufsize = skb->len->skb->data_len;
+
+			for (i = 0; i < nfrags; i++) {
+				skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+				void *addr = ((void *) page_address(frag->page + frag->page_offset));
+
+				tdinfo->skb_dma[i + 1] = pci_map_single(vptr->pdev, addr, frag->size, PCI_DMA_TODEVICE);
+
+				td_ptr->td_buf[i + 1].pa_low = cpu_to_le32(tdinfo->skb_dma[i + 1]);
+				td_ptr->td_buf[i + 1].pa_high = 0;
+				td_ptr->td_buf[i + 1].bufsize = frag->size;
+			}
+			tdinfo->nskb_dma = i - 1;
+			td_ptr->tdesc1.CMDZ = i;
+		}
+
+	} else
+#endif
+	{
+		/*
+		 *	Map the linear network buffer into PCI space and
+		 *	add it to the transmit ring.
+		 */
+		tdinfo->skb = skb;
+		tdinfo->skb_dma[0] = pci_map_single(vptr->pdev, skb->data, pktlen, PCI_DMA_TODEVICE);
+		td_ptr->tdesc0.pktsize = pktlen;
+		td_ptr->td_buf[0].pa_low = cpu_to_le32(tdinfo->skb_dma[0]);
+		td_ptr->td_buf[0].pa_high = 0;
+		td_ptr->td_buf[0].bufsize = td_ptr->tdesc0.pktsize;
+		tdinfo->nskb_dma = 1;
+		td_ptr->tdesc1.CMDZ = 2;
+	}
+
+	if (vptr->flags & VELOCITY_FLAGS_TAGGING) {
+		td_ptr->tdesc1.pqinf.VID = (vptr->options.vid & 0xfff);
+		td_ptr->tdesc1.pqinf.priority = 0;
+		td_ptr->tdesc1.pqinf.CFI = 0;
+		td_ptr->tdesc1.TCR |= TCR0_VETAG;
+	}
+
+	/*
+	 *	Handle hardware checksum
+	 */
+	if ((vptr->flags & VELOCITY_FLAGS_TX_CSUM)
+				 && (skb->ip_summed == CHECKSUM_HW)) {
+		struct iphdr *ip = skb->nh.iph;
+		if (ip->protocol == IPPROTO_TCP)
+			td_ptr->tdesc1.TCR |= TCR0_TCPCK;
+		else if (ip->protocol == IPPROTO_UDP)
+			td_ptr->tdesc1.TCR |= (TCR0_UDPCK);
+		td_ptr->tdesc1.TCR |= TCR0_IPCK;
+	}
+	{
+
+		int prev = index - 1;
+
+		if (prev < 0)
+			prev = vptr->options.numtx - 1;
+		td_ptr->tdesc0.owner = OWNED_BY_NIC;
+		vptr->td_used[qnum]++;
+		vptr->td_curr[qnum] = (index + 1) % vptr->options.numtx;
+
+		if (AVAIL_TD(vptr, qnum) < 1)
+			netif_stop_queue(dev);
+
+		td_ptr = &(vptr->td_rings[qnum][prev]);
+		td_ptr->td_buf[0].queue = 1;
+		mac_tx_queue_wake(vptr->mac_regs, qnum);
+	}
+	dev->trans_start = jiffies;
+	spin_unlock_irqrestore(&vptr->lock, flags);
+	return 0;
+}
+
+/**
+ *	velocity_intr		-	interrupt callback
+ *	@irq: interrupt number
+ *	@dev_instance: interrupting device
+ *	@pt_regs: CPU register state at interrupt
+ *
+ *	Called whenever an interrupt is generated by the velocity
+ *	adapter IRQ line. We may not be the source of the interrupt
+ *	and need to identify initially if we are, and if not exit as
+ *	efficiently as possible.
+ */
+ 
+static int velocity_intr(int irq, void *dev_instance, struct pt_regs *regs)
+{
+	struct net_device *dev = dev_instance;
+	struct velocity_info *vptr = dev->priv;
+	u32 isr_status;
+	int max_count = 0;
+
+
+	spin_lock(&vptr->lock);
+	isr_status = mac_read_isr(vptr->mac_regs);
+
+	/* Not us ? */
+	if (isr_status == 0) {
+		spin_unlock(&vptr->lock);
+		return IRQ_NONE;
+	}
+
+	mac_disable_int(vptr->mac_regs);
+
+	/*
+	 *	Keep processing the ISR until we have completed
+	 *	processing and the isr_status becomes zero
+	 */
+	 
+	while (isr_status != 0) {
+		mac_write_isr(vptr->mac_regs, isr_status);
+		if (isr_status & (~(ISR_PRXI | ISR_PPRXI | ISR_PTXI | ISR_PPTXI)))
+			velocity_error(vptr, isr_status);
+		if (isr_status & (ISR_PRXI | ISR_PPRXI))
+			max_count += velocity_rx_srv(vptr, isr_status);
+		if (isr_status & (ISR_PTXI | ISR_PPTXI))
+			max_count += velocity_tx_srv(vptr, isr_status);
+		isr_status = mac_read_isr(vptr->mac_regs);
+		if (max_count > vptr->options.int_works)
+		{
+			printk(KERN_WARNING "%s: excessive work at interrupt.\n", 
+				dev->name);
+			max_count = 0;
+		}
+	}
+	spin_unlock(&vptr->lock);
+	mac_enable_int(vptr->mac_regs);
+	return IRQ_HANDLED;
+
+}
+
+
+/**
+ *	velocity_set_multi	-	filter list change callback
+ *	@dev: network device
+ *
+ *	Called by the network layer when the filter lists need to change
+ *	for a velocity adapter. Reload the CAMs with the new address
+ *	filter ruleset.
+ */
+ 
+static void velocity_set_multi(struct net_device *dev)
+{
+	struct velocity_info *vptr = dev->priv;
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+	u8 rx_mode;
+	int i;
+	struct dev_mc_list *mclist;
+
+	if (dev->flags & IFF_PROMISC) {	/* Set promiscuous. */
+		/* Unconditionally log net taps. */
+		printk(KERN_NOTICE "%s: Promiscuous mode enabled.\n", dev->name);
+		writel(0xffffffff, &regs->MARCAM[0]);
+		writel(0xffffffff, &regs->MARCAM[4]);
+		rx_mode = (RCR_AM | RCR_AB | RCR_PROM);
+	} else if ((dev->mc_count > vptr->multicast_limit)
+		   || (dev->flags & IFF_ALLMULTI)) {
+		writel(0xffffffff, &regs->MARCAM[0]);
+		writel(0xffffffff, &regs->MARCAM[4]);
+		rx_mode = (RCR_AM | RCR_AB);
+	} else {
+		int offset = MCAM_SIZE - vptr->multicast_limit;
+		mac_get_cam_mask(regs, vptr->mCAMmask, VELOCITY_MULTICAST_CAM);
+
+		for (i = 0, mclist = dev->mc_list; mclist && i < dev->mc_count; i++, mclist = mclist->next) {
+			mac_set_cam(regs, i + offset, mclist->dmi_addr, VELOCITY_MULTICAST_CAM);
+			vptr->mCAMmask[(offset + i) / 8] |= 1 << ((offset + i) & 7);
+		}
+
+		mac_set_cam_mask(regs, vptr->mCAMmask, VELOCITY_MULTICAST_CAM);
+		rx_mode = (RCR_AM | RCR_AB);
+	}
+	if (dev->mtu > 1500)
+		rx_mode |= RCR_AL;
+
+	BYTE_REG_BITS_ON(rx_mode, &regs->RCR);
+
+}
+
+/**
+ *	velocity_get_status	-	statistics callback
+ *	@dev: network device
+ *
+ *	Callback from the network layer to allow driver statistics
+ *	to be resynchronized with hardware collected state. In the
+ *	case of the velocity we need to pull the MIB counters from
+ *	the hardware into the counters before letting the network
+ *	layer display them.
+ */
+ 
+static struct net_device_stats *velocity_get_stats(struct net_device *dev)
+{
+	struct velocity_info *vptr = dev->priv;
+	
+	/* If the hardware is down, don't touch MII */
+	if(!netif_running(dev))
+		return &vptr->stats;
+
+	spin_lock_irq(&vptr->lock);
+	velocity_update_hw_mibs(vptr);
+	spin_unlock_irq(&vptr->lock);
+
+	vptr->stats.rx_packets = vptr->mib_counter[HW_MIB_ifRxAllPkts];
+	vptr->stats.rx_errors = vptr->mib_counter[HW_MIB_ifRxErrorPkts];
+	vptr->stats.rx_length_errors = vptr->mib_counter[HW_MIB_ifInRangeLengthErrors];
+
+//  unsigned long   rx_dropped;     /* no space in linux buffers    */
+	vptr->stats.collisions = vptr->mib_counter[HW_MIB_ifTxEtherCollisions];
+	/* detailed rx_errors: */
+//  unsigned long   rx_length_errors;
+//  unsigned long   rx_over_errors;     /* receiver ring buff overflow  */
+	vptr->stats.rx_crc_errors = vptr->mib_counter[HW_MIB_ifRxPktCRCE];
+//  unsigned long   rx_frame_errors;    /* recv'd frame alignment error */
+//  unsigned long   rx_fifo_errors;     /* recv'r fifo overrun      */
+//  unsigned long   rx_missed_errors;   /* receiver missed packet   */
+
+	/* detailed tx_errors */
+//  unsigned long   tx_fifo_errors;
+
+	return &vptr->stats;
+}
+
+
+/**
+ *	velocity_ioctl		-	ioctl entry point
+ *	@dev: network device
+ *	@rq: interface request ioctl
+ *	@cmd: command code
+ *
+ *	Called when the user issues an ioctl request to the network
+ *	device in question. The velocity interface supports MII.
+ */
+ 
+static int velocity_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+{
+	struct velocity_info *vptr = dev->priv;
+	int ret;
+
+	/* If we are asked for information and the device is power
+	   saving then we need to bring the device back up to talk to it */
+	   	
+	if (!netif_running(dev))
+		pci_set_power_state(vptr->pdev, PCI_D0);
+		
+	switch (cmd) {
+	case SIOCGMIIPHY:	/* Get address of MII PHY in use. */
+	case SIOCGMIIREG:	/* Read MII PHY register. */
+	case SIOCSMIIREG:	/* Write to MII PHY register. */
+		ret = velocity_mii_ioctl(dev, rq, cmd);
+		break;
+
+	default:
+		ret = -EOPNOTSUPP;
+	}
+	if (!netif_running(dev))
+		pci_set_power_state(vptr->pdev, PCI_D3hot);
+		
+		
+	return ret;
+}
+
+/*
+ *	Definition for our device driver. The PCI layer interface
+ *	uses this to handle all our card discover and plugging
+ */
+ 
+static struct pci_driver velocity_driver = {
+      .name	= VELOCITY_NAME,
+      .id_table	= velocity_id_table,
+      .probe	= velocity_found1,
+      .remove	= __devexit_p(velocity_remove1),
+#ifdef CONFIG_PM
+      .suspend	= velocity_suspend,
+      .resume	= velocity_resume,
+#endif
+};
+
+/**
+ *	velocity_init_module	-	load time function
+ *
+ *	Called when the velocity module is loaded. The PCI driver
+ *	is registered with the PCI layer, and in turn will call
+ *	the probe functions for each velocity adapter installed
+ *	in the system.
+ */
+ 
+static int __init velocity_init_module(void)
+{
+	int ret;
+
+	velocity_register_notifier();
+	ret = pci_module_init(&velocity_driver);
+	if (ret < 0)
+		velocity_unregister_notifier();
+	return ret;
+}
+
+/**
+ *	velocity_cleanup	-	module unload
+ *
+ *	When the velocity hardware is unloaded this function is called.
+ *	It will clean up the notifiers and the unregister the PCI 
+ *	driver interface for this hardware. This in turn cleans up
+ *	all discovered interfaces before returning from the function
+ */
+ 
+static void __exit velocity_cleanup_module(void)
+{
+	velocity_unregister_notifier();
+	pci_unregister_driver(&velocity_driver);
+}
+
+module_init(velocity_init_module);
+module_exit(velocity_cleanup_module);
+
+
+/*
+ * MII access , media link mode setting functions
+ */
+ 
+ 
+/**
+ *	mii_init	-	set up MII
+ *	@vptr: velocity adapter
+ *	@mii_status:  links tatus
+ *
+ *	Set up the PHY for the current link state.
+ */
+ 
+static void mii_init(struct velocity_info *vptr, u32 mii_status)
+{
+	u16 BMCR;
+
+	switch (PHYID_GET_PHY_ID(vptr->phy_id)) {
+	case PHYID_CICADA_CS8201:
+		/*
+		 *	Reset to hardware default
+		 */
+		MII_REG_BITS_OFF((ANAR_ASMDIR | ANAR_PAUSE), MII_REG_ANAR, vptr->mac_regs);
+		/*
+		 *	Turn on ECHODIS bit in NWay-forced full mode and turn it
+		 *	off it in NWay-forced half mode for NWay-forced v.s. 
+		 *	legacy-forced issue.
+		 */
+		if (vptr->mii_status & VELOCITY_DUPLEX_FULL)
+			MII_REG_BITS_ON(TCSR_ECHODIS, MII_REG_TCSR, vptr->mac_regs);
+		else
+			MII_REG_BITS_OFF(TCSR_ECHODIS, MII_REG_TCSR, vptr->mac_regs);
+		/*
+		 *	Turn on Link/Activity LED enable bit for CIS8201
+		 */
+		MII_REG_BITS_ON(PLED_LALBE, MII_REG_PLED, vptr->mac_regs);
+		break;
+	case PHYID_VT3216_32BIT:
+	case PHYID_VT3216_64BIT:
+		/*
+		 *	Reset to hardware default
+		 */
+		MII_REG_BITS_ON((ANAR_ASMDIR | ANAR_PAUSE), MII_REG_ANAR, vptr->mac_regs);
+		/*
+		 *	Turn on ECHODIS bit in NWay-forced full mode and turn it
+		 *	off it in NWay-forced half mode for NWay-forced v.s. 
+		 *	legacy-forced issue
+		 */
+		if (vptr->mii_status & VELOCITY_DUPLEX_FULL)
+			MII_REG_BITS_ON(TCSR_ECHODIS, MII_REG_TCSR, vptr->mac_regs);
+		else
+			MII_REG_BITS_OFF(TCSR_ECHODIS, MII_REG_TCSR, vptr->mac_regs);
+		break;
+
+	case PHYID_MARVELL_1000:
+	case PHYID_MARVELL_1000S:
+		/*
+		 *	Assert CRS on Transmit 
+		 */
+		MII_REG_BITS_ON(PSCR_ACRSTX, MII_REG_PSCR, vptr->mac_regs);
+		/*
+		 *	Reset to hardware default 
+		 */
+		MII_REG_BITS_ON((ANAR_ASMDIR | ANAR_PAUSE), MII_REG_ANAR, vptr->mac_regs);
+		break;
+	default:
+		;
+	}
+	velocity_mii_read(vptr->mac_regs, MII_REG_BMCR, &BMCR);
+	if (BMCR & BMCR_ISO) {
+		BMCR &= ~BMCR_ISO;
+		velocity_mii_write(vptr->mac_regs, MII_REG_BMCR, BMCR);
+	}
+}
+
+/**
+ *	safe_disable_mii_autopoll	-	autopoll off
+ *	@regs: velocity registers
+ *
+ *	Turn off the autopoll and wait for it to disable on the chip
+ */
+ 
+static void safe_disable_mii_autopoll(struct mac_regs __iomem * regs)
+{
+	u16 ww;
+
+	/*  turn off MAUTO */
+	writeb(0, &regs->MIICR);
+	for (ww = 0; ww < W_MAX_TIMEOUT; ww++) {
+		udelay(1);
+		if (BYTE_REG_BITS_IS_ON(MIISR_MIDLE, &regs->MIISR))
+			break;
+	}
+}
+
+/**
+ *	enable_mii_autopoll	-	turn on autopolling
+ *	@regs: velocity registers
+ *
+ *	Enable the MII link status autopoll feature on the Velocity
+ *	hardware. Wait for it to enable.
+ */
+
+static void enable_mii_autopoll(struct mac_regs __iomem * regs)
+{
+	int ii;
+
+	writeb(0, &(regs->MIICR));
+	writeb(MIIADR_SWMPL, &regs->MIIADR);
+
+	for (ii = 0; ii < W_MAX_TIMEOUT; ii++) {
+		udelay(1);
+		if (BYTE_REG_BITS_IS_ON(MIISR_MIDLE, &regs->MIISR))
+			break;
+	}
+
+	writeb(MIICR_MAUTO, &regs->MIICR);
+
+	for (ii = 0; ii < W_MAX_TIMEOUT; ii++) {
+		udelay(1);
+		if (!BYTE_REG_BITS_IS_ON(MIISR_MIDLE, &regs->MIISR))
+			break;
+	}
+
+}
+
+/**
+ *	velocity_mii_read	-	read MII data
+ *	@regs: velocity registers
+ *	@index: MII register index
+ *	@data: buffer for received data
+ *
+ *	Perform a single read of an MII 16bit register. Returns zero
+ *	on success or -ETIMEDOUT if the PHY did not respond.
+ */
+ 
+static int velocity_mii_read(struct mac_regs __iomem *regs, u8 index, u16 *data)
+{
+	u16 ww;
+
+	/*
+	 *	Disable MIICR_MAUTO, so that mii addr can be set normally
+	 */
+	safe_disable_mii_autopoll(regs);
+
+	writeb(index, &regs->MIIADR);
+
+	BYTE_REG_BITS_ON(MIICR_RCMD, &regs->MIICR);
+
+	for (ww = 0; ww < W_MAX_TIMEOUT; ww++) {
+		if (!(readb(&regs->MIICR) & MIICR_RCMD))
+			break;
+	}
+
+	*data = readw(&regs->MIIDATA);
+
+	enable_mii_autopoll(regs);
+	if (ww == W_MAX_TIMEOUT)
+		return -ETIMEDOUT;
+	return 0;
+}
+
+/**
+ *	velocity_mii_write	-	write MII data
+ *	@regs: velocity registers
+ *	@index: MII register index
+ *	@data: 16bit data for the MII register
+ *
+ *	Perform a single write to an MII 16bit register. Returns zero
+ *	on success or -ETIMEDOUT if the PHY did not respond.
+ */
+ 
+static int velocity_mii_write(struct mac_regs __iomem *regs, u8 mii_addr, u16 data)
+{
+	u16 ww;
+
+	/*
+	 *	Disable MIICR_MAUTO, so that mii addr can be set normally
+	 */
+	safe_disable_mii_autopoll(regs);
+
+	/* MII reg offset */
+	writeb(mii_addr, &regs->MIIADR);
+	/* set MII data */
+	writew(data, &regs->MIIDATA);
+
+	/* turn on MIICR_WCMD */
+	BYTE_REG_BITS_ON(MIICR_WCMD, &regs->MIICR);
+
+	/* W_MAX_TIMEOUT is the timeout period */
+	for (ww = 0; ww < W_MAX_TIMEOUT; ww++) {
+		udelay(5);
+		if (!(readb(&regs->MIICR) & MIICR_WCMD))
+			break;
+	}
+	enable_mii_autopoll(regs);
+
+	if (ww == W_MAX_TIMEOUT)
+		return -ETIMEDOUT;
+	return 0;
+}
+
+/**
+ *	velocity_get_opt_media_mode	-	get media selection
+ *	@vptr: velocity adapter
+ *
+ *	Get the media mode stored in EEPROM or module options and load
+ *	mii_status accordingly. The requested link state information
+ *	is also returned.
+ */
+ 
+static u32 velocity_get_opt_media_mode(struct velocity_info *vptr)
+{
+	u32 status = 0;
+
+	switch (vptr->options.spd_dpx) {
+	case SPD_DPX_AUTO:
+		status = VELOCITY_AUTONEG_ENABLE;
+		break;
+	case SPD_DPX_100_FULL:
+		status = VELOCITY_SPEED_100 | VELOCITY_DUPLEX_FULL;
+		break;
+	case SPD_DPX_10_FULL:
+		status = VELOCITY_SPEED_10 | VELOCITY_DUPLEX_FULL;
+		break;
+	case SPD_DPX_100_HALF:
+		status = VELOCITY_SPEED_100;
+		break;
+	case SPD_DPX_10_HALF:
+		status = VELOCITY_SPEED_10;
+		break;
+	}
+	vptr->mii_status = status;
+	return status;
+}
+
+/**
+ *	mii_set_auto_on		-	autonegotiate on
+ *	@vptr: velocity
+ *
+ *	Enable autonegotation on this interface
+ */
+ 
+static void mii_set_auto_on(struct velocity_info *vptr)
+{
+	if (MII_REG_BITS_IS_ON(BMCR_AUTO, MII_REG_BMCR, vptr->mac_regs))
+		MII_REG_BITS_ON(BMCR_REAUTO, MII_REG_BMCR, vptr->mac_regs);
+	else
+		MII_REG_BITS_ON(BMCR_AUTO, MII_REG_BMCR, vptr->mac_regs);
+}
+
+
+/*
+static void mii_set_auto_off(struct velocity_info * vptr)
+{
+    MII_REG_BITS_OFF(BMCR_AUTO, MII_REG_BMCR, vptr->mac_regs);
+}
+*/
+
+/**
+ *	set_mii_flow_control	-	flow control setup
+ *	@vptr: velocity interface
+ *
+ *	Set up the flow control on this interface according to
+ *	the supplied user/eeprom options.
+ */
+ 
+static void set_mii_flow_control(struct velocity_info *vptr)
+{
+	/*Enable or Disable PAUSE in ANAR */
+	switch (vptr->options.flow_cntl) {
+	case FLOW_CNTL_TX:
+		MII_REG_BITS_OFF(ANAR_PAUSE, MII_REG_ANAR, vptr->mac_regs);
+		MII_REG_BITS_ON(ANAR_ASMDIR, MII_REG_ANAR, vptr->mac_regs);
+		break;
+
+	case FLOW_CNTL_RX:
+		MII_REG_BITS_ON(ANAR_PAUSE, MII_REG_ANAR, vptr->mac_regs);
+		MII_REG_BITS_ON(ANAR_ASMDIR, MII_REG_ANAR, vptr->mac_regs);
+		break;
+
+	case FLOW_CNTL_TX_RX:
+		MII_REG_BITS_ON(ANAR_PAUSE, MII_REG_ANAR, vptr->mac_regs);
+		MII_REG_BITS_ON(ANAR_ASMDIR, MII_REG_ANAR, vptr->mac_regs);
+		break;
+
+	case FLOW_CNTL_DISABLE:
+		MII_REG_BITS_OFF(ANAR_PAUSE, MII_REG_ANAR, vptr->mac_regs);
+		MII_REG_BITS_OFF(ANAR_ASMDIR, MII_REG_ANAR, vptr->mac_regs);
+		break;
+	default:
+		break;
+	}
+}
+
+/**
+ *	velocity_set_media_mode		-	set media mode
+ *	@mii_status: old MII link state
+ *
+ *	Check the media link state and configure the flow control
+ *	PHY and also velocity hardware setup accordingly. In particular
+ *	we need to set up CD polling and frame bursting.
+ */
+ 
+static int velocity_set_media_mode(struct velocity_info *vptr, u32 mii_status)
+{
+	u32 curr_status;
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+
+	vptr->mii_status = mii_check_media_mode(vptr->mac_regs);
+	curr_status = vptr->mii_status & (~VELOCITY_LINK_FAIL);
+
+	/* Set mii link status */
+	set_mii_flow_control(vptr);
+
+	/*
+	   Check if new status is consisent with current status
+	   if (((mii_status & curr_status) & VELOCITY_AUTONEG_ENABLE)
+	   || (mii_status==curr_status)) {
+	   vptr->mii_status=mii_check_media_mode(vptr->mac_regs);
+	   vptr->mii_status=check_connection_type(vptr->mac_regs);
+	   VELOCITY_PRT(MSG_LEVEL_INFO, "Velocity link no change\n");
+	   return 0;
+	   }
+	 */
+
+	if (PHYID_GET_PHY_ID(vptr->phy_id) == PHYID_CICADA_CS8201) {
+		MII_REG_BITS_ON(AUXCR_MDPPS, MII_REG_AUXCR, vptr->mac_regs);
+	}
+
+	/*
+	 *	If connection type is AUTO
+	 */
+	if (mii_status & VELOCITY_AUTONEG_ENABLE) {
+		VELOCITY_PRT(MSG_LEVEL_INFO, "Velocity is AUTO mode\n");
+		/* clear force MAC mode bit */
+		BYTE_REG_BITS_OFF(CHIPGCR_FCMODE, &regs->CHIPGCR);
+		/* set duplex mode of MAC according to duplex mode of MII */
+		MII_REG_BITS_ON(ANAR_TXFD | ANAR_TX | ANAR_10FD | ANAR_10, MII_REG_ANAR, vptr->mac_regs);
+		MII_REG_BITS_ON(G1000CR_1000FD | G1000CR_1000, MII_REG_G1000CR, vptr->mac_regs);
+		MII_REG_BITS_ON(BMCR_SPEED1G, MII_REG_BMCR, vptr->mac_regs);
+
+		/* enable AUTO-NEGO mode */
+		mii_set_auto_on(vptr);
+	} else {
+		u16 ANAR;
+		u8 CHIPGCR;
+
+		/*
+		 * 1. if it's 3119, disable frame bursting in halfduplex mode
+		 *    and enable it in fullduplex mode
+		 * 2. set correct MII/GMII and half/full duplex mode in CHIPGCR
+		 * 3. only enable CD heart beat counter in 10HD mode
+		 */
+
+		/* set force MAC mode bit */
+		BYTE_REG_BITS_ON(CHIPGCR_FCMODE, &regs->CHIPGCR);
+
+		CHIPGCR = readb(&regs->CHIPGCR);
+		CHIPGCR &= ~CHIPGCR_FCGMII;
+
+		if (mii_status & VELOCITY_DUPLEX_FULL) {
+			CHIPGCR |= CHIPGCR_FCFDX;
+			writeb(CHIPGCR, &regs->CHIPGCR);
+			VELOCITY_PRT(MSG_LEVEL_INFO, "set Velocity to forced full mode\n");
+			if (vptr->rev_id < REV_ID_VT3216_A0)
+				BYTE_REG_BITS_OFF(TCR_TB2BDIS, &regs->TCR);
+		} else {
+			CHIPGCR &= ~CHIPGCR_FCFDX;
+			VELOCITY_PRT(MSG_LEVEL_INFO, "set Velocity to forced half mode\n");
+			writeb(CHIPGCR, &regs->CHIPGCR);
+			if (vptr->rev_id < REV_ID_VT3216_A0)
+				BYTE_REG_BITS_ON(TCR_TB2BDIS, &regs->TCR);
+		}
+
+		MII_REG_BITS_OFF(G1000CR_1000FD | G1000CR_1000, MII_REG_G1000CR, vptr->mac_regs);
+
+		if (!(mii_status & VELOCITY_DUPLEX_FULL) && (mii_status & VELOCITY_SPEED_10)) {
+			BYTE_REG_BITS_OFF(TESTCFG_HBDIS, &regs->TESTCFG);
+		} else {
+			BYTE_REG_BITS_ON(TESTCFG_HBDIS, &regs->TESTCFG);
+		}
+		/* MII_REG_BITS_OFF(BMCR_SPEED1G, MII_REG_BMCR, vptr->mac_regs); */
+		velocity_mii_read(vptr->mac_regs, MII_REG_ANAR, &ANAR);
+		ANAR &= (~(ANAR_TXFD | ANAR_TX | ANAR_10FD | ANAR_10));
+		if (mii_status & VELOCITY_SPEED_100) {
+			if (mii_status & VELOCITY_DUPLEX_FULL)
+				ANAR |= ANAR_TXFD;
+			else
+				ANAR |= ANAR_TX;
+		} else {
+			if (mii_status & VELOCITY_DUPLEX_FULL)
+				ANAR |= ANAR_10FD;
+			else
+				ANAR |= ANAR_10;
+		}
+		velocity_mii_write(vptr->mac_regs, MII_REG_ANAR, ANAR);
+		/* enable AUTO-NEGO mode */
+		mii_set_auto_on(vptr);
+		/* MII_REG_BITS_ON(BMCR_AUTO, MII_REG_BMCR, vptr->mac_regs); */
+	}
+	/* vptr->mii_status=mii_check_media_mode(vptr->mac_regs); */
+	/* vptr->mii_status=check_connection_type(vptr->mac_regs); */
+	return VELOCITY_LINK_CHANGE;
+}
+
+/**
+ *	mii_check_media_mode	-	check media state
+ *	@regs: velocity registers
+ *
+ *	Check the current MII status and determine the link status
+ *	accordingly
+ */
+ 
+static u32 mii_check_media_mode(struct mac_regs __iomem * regs)
+{
+	u32 status = 0;
+	u16 ANAR;
+
+	if (!MII_REG_BITS_IS_ON(BMSR_LNK, MII_REG_BMSR, regs))
+		status |= VELOCITY_LINK_FAIL;
+
+	if (MII_REG_BITS_IS_ON(G1000CR_1000FD, MII_REG_G1000CR, regs))
+		status |= VELOCITY_SPEED_1000 | VELOCITY_DUPLEX_FULL;
+	else if (MII_REG_BITS_IS_ON(G1000CR_1000, MII_REG_G1000CR, regs))
+		status |= (VELOCITY_SPEED_1000);
+	else {
+		velocity_mii_read(regs, MII_REG_ANAR, &ANAR);
+		if (ANAR & ANAR_TXFD)
+			status |= (VELOCITY_SPEED_100 | VELOCITY_DUPLEX_FULL);
+		else if (ANAR & ANAR_TX)
+			status |= VELOCITY_SPEED_100;
+		else if (ANAR & ANAR_10FD)
+			status |= (VELOCITY_SPEED_10 | VELOCITY_DUPLEX_FULL);
+		else
+			status |= (VELOCITY_SPEED_10);
+	}
+
+	if (MII_REG_BITS_IS_ON(BMCR_AUTO, MII_REG_BMCR, regs)) {
+		velocity_mii_read(regs, MII_REG_ANAR, &ANAR);
+		if ((ANAR & (ANAR_TXFD | ANAR_TX | ANAR_10FD | ANAR_10))
+		    == (ANAR_TXFD | ANAR_TX | ANAR_10FD | ANAR_10)) {
+			if (MII_REG_BITS_IS_ON(G1000CR_1000 | G1000CR_1000FD, MII_REG_G1000CR, regs))
+				status |= VELOCITY_AUTONEG_ENABLE;
+		}
+	}
+
+	return status;
+}
+
+static u32 check_connection_type(struct mac_regs __iomem * regs)
+{
+	u32 status = 0;
+	u8 PHYSR0;
+	u16 ANAR;
+	PHYSR0 = readb(&regs->PHYSR0);
+
+	/*
+	   if (!(PHYSR0 & PHYSR0_LINKGD))
+	   status|=VELOCITY_LINK_FAIL;
+	 */
+
+	if (PHYSR0 & PHYSR0_FDPX)
+		status |= VELOCITY_DUPLEX_FULL;
+
+	if (PHYSR0 & PHYSR0_SPDG)
+		status |= VELOCITY_SPEED_1000;
+	if (PHYSR0 & PHYSR0_SPD10)
+		status |= VELOCITY_SPEED_10;
+	else
+		status |= VELOCITY_SPEED_100;
+
+	if (MII_REG_BITS_IS_ON(BMCR_AUTO, MII_REG_BMCR, regs)) {
+		velocity_mii_read(regs, MII_REG_ANAR, &ANAR);
+		if ((ANAR & (ANAR_TXFD | ANAR_TX | ANAR_10FD | ANAR_10))
+		    == (ANAR_TXFD | ANAR_TX | ANAR_10FD | ANAR_10)) {
+			if (MII_REG_BITS_IS_ON(G1000CR_1000 | G1000CR_1000FD, MII_REG_G1000CR, regs))
+				status |= VELOCITY_AUTONEG_ENABLE;
+		}
+	}
+
+	return status;
+}
+
+/**
+ *	enable_flow_control_ability	-	flow control
+ *	@vptr: veloity to configure
+ *
+ *	Set up flow control according to the flow control options
+ *	determined by the eeprom/configuration.
+ */
+
+static void enable_flow_control_ability(struct velocity_info *vptr)
+{
+
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+
+	switch (vptr->options.flow_cntl) {
+
+	case FLOW_CNTL_DEFAULT:
+		if (BYTE_REG_BITS_IS_ON(PHYSR0_RXFLC, &regs->PHYSR0))
+			writel(CR0_FDXRFCEN, &regs->CR0Set);
+		else
+			writel(CR0_FDXRFCEN, &regs->CR0Clr);
+
+		if (BYTE_REG_BITS_IS_ON(PHYSR0_TXFLC, &regs->PHYSR0))
+			writel(CR0_FDXTFCEN, &regs->CR0Set);
+		else
+			writel(CR0_FDXTFCEN, &regs->CR0Clr);
+		break;
+
+	case FLOW_CNTL_TX:
+		writel(CR0_FDXTFCEN, &regs->CR0Set);
+		writel(CR0_FDXRFCEN, &regs->CR0Clr);
+		break;
+
+	case FLOW_CNTL_RX:
+		writel(CR0_FDXRFCEN, &regs->CR0Set);
+		writel(CR0_FDXTFCEN, &regs->CR0Clr);
+		break;
+
+	case FLOW_CNTL_TX_RX:
+		writel(CR0_FDXTFCEN, &regs->CR0Set);
+		writel(CR0_FDXRFCEN, &regs->CR0Set);
+		break;
+
+	case FLOW_CNTL_DISABLE:
+		writel(CR0_FDXRFCEN, &regs->CR0Clr);
+		writel(CR0_FDXTFCEN, &regs->CR0Clr);
+		break;
+
+	default:
+		break;
+	}
+
+}
+
+
+/**
+ *	velocity_ethtool_up	-	pre hook for ethtool
+ *	@dev: network device
+ *
+ *	Called before an ethtool operation. We need to make sure the
+ *	chip is out of D3 state before we poke at it.
+ */
+ 
+static int velocity_ethtool_up(struct net_device *dev)
+{
+	struct velocity_info *vptr = dev->priv;
+	if (!netif_running(dev))
+		pci_set_power_state(vptr->pdev, PCI_D0);
+	return 0;
+}	
+
+/**
+ *	velocity_ethtool_down	-	post hook for ethtool
+ *	@dev: network device
+ *
+ *	Called after an ethtool operation. Restore the chip back to D3
+ *	state if it isn't running.
+ */
+ 
+static void velocity_ethtool_down(struct net_device *dev)
+{
+	struct velocity_info *vptr = dev->priv;
+	if (!netif_running(dev))
+		pci_set_power_state(vptr->pdev, PCI_D3hot);
+}
+
+static int velocity_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+	struct velocity_info *vptr = dev->priv;
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+	u32 status;
+	status = check_connection_type(vptr->mac_regs);
+
+	cmd->supported = SUPPORTED_TP | SUPPORTED_Autoneg | SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full | SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full;
+	if (status & VELOCITY_SPEED_100)
+		cmd->speed = SPEED_100;
+	else
+		cmd->speed = SPEED_10;
+	cmd->autoneg = (status & VELOCITY_AUTONEG_ENABLE) ? AUTONEG_ENABLE : AUTONEG_DISABLE;
+	cmd->port = PORT_TP;
+	cmd->transceiver = XCVR_INTERNAL;
+	cmd->phy_address = readb(&regs->MIIADR) & 0x1F;
+
+	if (status & VELOCITY_DUPLEX_FULL)
+		cmd->duplex = DUPLEX_FULL;
+	else
+		cmd->duplex = DUPLEX_HALF;
+		
+	return 0;
+}
+
+static int velocity_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+	struct velocity_info *vptr = dev->priv;
+	u32 curr_status;
+	u32 new_status = 0;
+	int ret = 0;
+	
+	curr_status = check_connection_type(vptr->mac_regs);
+	curr_status &= (~VELOCITY_LINK_FAIL);
+
+	new_status |= ((cmd->autoneg) ? VELOCITY_AUTONEG_ENABLE : 0);
+	new_status |= ((cmd->speed == SPEED_100) ? VELOCITY_SPEED_100 : 0);
+	new_status |= ((cmd->speed == SPEED_10) ? VELOCITY_SPEED_10 : 0);
+	new_status |= ((cmd->duplex == DUPLEX_FULL) ? VELOCITY_DUPLEX_FULL : 0);
+
+	if ((new_status & VELOCITY_AUTONEG_ENABLE) && (new_status != (curr_status | VELOCITY_AUTONEG_ENABLE)))
+		ret = -EINVAL;
+	else
+		velocity_set_media_mode(vptr, new_status);
+
+	return ret;
+}
+
+static u32 velocity_get_link(struct net_device *dev)
+{
+	struct velocity_info *vptr = dev->priv;
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+	return BYTE_REG_BITS_IS_ON(PHYSR0_LINKGD, &regs->PHYSR0)  ? 0 : 1;
+}
+
+static void velocity_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
+{
+	struct velocity_info *vptr = dev->priv;
+	strcpy(info->driver, VELOCITY_NAME);
+	strcpy(info->version, VELOCITY_VERSION);
+	strcpy(info->bus_info, pci_name(vptr->pdev));
+}
+
+static void velocity_ethtool_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+	struct velocity_info *vptr = dev->priv;
+	wol->supported = WAKE_PHY | WAKE_MAGIC | WAKE_UCAST | WAKE_ARP;
+	wol->wolopts |= WAKE_MAGIC;
+	/*
+	   if (vptr->wol_opts & VELOCITY_WOL_PHY)
+		   wol.wolopts|=WAKE_PHY;
+			 */
+	if (vptr->wol_opts & VELOCITY_WOL_UCAST)
+		wol->wolopts |= WAKE_UCAST;
+	if (vptr->wol_opts & VELOCITY_WOL_ARP)
+		wol->wolopts |= WAKE_ARP;
+	memcpy(&wol->sopass, vptr->wol_passwd, 6);
+}
+
+static int velocity_ethtool_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+	struct velocity_info *vptr = dev->priv;
+
+	if (!(wol->wolopts & (WAKE_PHY | WAKE_MAGIC | WAKE_UCAST | WAKE_ARP)))
+		return -EFAULT;
+	vptr->wol_opts = VELOCITY_WOL_MAGIC;
+
+	/*
+	   if (wol.wolopts & WAKE_PHY) {
+	   vptr->wol_opts|=VELOCITY_WOL_PHY;
+	   vptr->flags |=VELOCITY_FLAGS_WOL_ENABLED;
+	   }
+	 */
+
+	if (wol->wolopts & WAKE_MAGIC) {
+		vptr->wol_opts |= VELOCITY_WOL_MAGIC;
+		vptr->flags |= VELOCITY_FLAGS_WOL_ENABLED;
+	}
+	if (wol->wolopts & WAKE_UCAST) {
+		vptr->wol_opts |= VELOCITY_WOL_UCAST;
+		vptr->flags |= VELOCITY_FLAGS_WOL_ENABLED;
+	}
+	if (wol->wolopts & WAKE_ARP) {
+		vptr->wol_opts |= VELOCITY_WOL_ARP;
+		vptr->flags |= VELOCITY_FLAGS_WOL_ENABLED;
+	}
+	memcpy(vptr->wol_passwd, wol->sopass, 6);
+	return 0;
+}
+
+static u32 velocity_get_msglevel(struct net_device *dev)
+{
+	return msglevel;
+}
+
+static void velocity_set_msglevel(struct net_device *dev, u32 value)
+{
+	 msglevel = value;
+}
+
+static struct ethtool_ops velocity_ethtool_ops = {
+	.get_settings	=	velocity_get_settings,
+	.set_settings	=	velocity_set_settings,
+	.get_drvinfo	=	velocity_get_drvinfo,
+	.get_wol	=	velocity_ethtool_get_wol,
+	.set_wol	=	velocity_ethtool_set_wol,
+	.get_msglevel	=	velocity_get_msglevel,
+	.set_msglevel	=	velocity_set_msglevel,
+	.get_link	=	velocity_get_link,
+	.begin		=	velocity_ethtool_up,
+	.complete	=	velocity_ethtool_down
+};
+
+/**
+ *	velocity_mii_ioctl		-	MII ioctl handler
+ *	@dev: network device
+ *	@ifr: the ifreq block for the ioctl
+ *	@cmd: the command
+ *
+ *	Process MII requests made via ioctl from the network layer. These
+ *	are used by tools like kudzu to interrogate the link state of the
+ *	hardware
+ */
+ 
+static int velocity_mii_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
+{
+	struct velocity_info *vptr = dev->priv;
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+	unsigned long flags;
+	struct mii_ioctl_data *miidata = if_mii(ifr);
+	int err;
+	
+	switch (cmd) {
+	case SIOCGMIIPHY:
+		miidata->phy_id = readb(&regs->MIIADR) & 0x1f;
+		break;
+	case SIOCGMIIREG:
+		if (!capable(CAP_NET_ADMIN))
+			return -EPERM;
+		if(velocity_mii_read(vptr->mac_regs, miidata->reg_num & 0x1f, &(miidata->val_out)) < 0)
+			return -ETIMEDOUT;
+		break;
+	case SIOCSMIIREG:
+		if (!capable(CAP_NET_ADMIN))
+			return -EPERM;
+		spin_lock_irqsave(&vptr->lock, flags);
+		err = velocity_mii_write(vptr->mac_regs, miidata->reg_num & 0x1f, miidata->val_in);
+		spin_unlock_irqrestore(&vptr->lock, flags);
+		check_connection_type(vptr->mac_regs);
+		if(err)
+			return err;
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+	return 0;
+}
+
+#ifdef CONFIG_PM
+
+/**
+ *	velocity_save_context	-	save registers
+ *	@vptr: velocity 
+ *	@context: buffer for stored context
+ *
+ *	Retrieve the current configuration from the velocity hardware
+ *	and stash it in the context structure, for use by the context
+ *	restore functions. This allows us to save things we need across
+ *	power down states
+ */
+ 
+static void velocity_save_context(struct velocity_info *vptr, struct velocity_context * context)
+{
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+	u16 i;
+	u8 __iomem *ptr = (u8 __iomem *)regs;
+
+	for (i = MAC_REG_PAR; i < MAC_REG_CR0_CLR; i += 4)
+		*((u32 *) (context->mac_reg + i)) = readl(ptr + i);
+
+	for (i = MAC_REG_MAR; i < MAC_REG_TDCSR_CLR; i += 4)
+		*((u32 *) (context->mac_reg + i)) = readl(ptr + i);
+
+	for (i = MAC_REG_RDBASE_LO; i < MAC_REG_FIFO_TEST0; i += 4)
+		*((u32 *) (context->mac_reg + i)) = readl(ptr + i);
+
+}
+
+/**
+ *	velocity_restore_context	-	restore registers
+ *	@vptr: velocity 
+ *	@context: buffer for stored context
+ *
+ *	Reload the register configuration from the velocity context 
+ *	created by velocity_save_context.
+ */
+ 
+static void velocity_restore_context(struct velocity_info *vptr, struct velocity_context *context)
+{
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+	int i;
+	u8 __iomem *ptr = (u8 __iomem *)regs;
+
+	for (i = MAC_REG_PAR; i < MAC_REG_CR0_SET; i += 4) {
+		writel(*((u32 *) (context->mac_reg + i)), ptr + i);
+	}
+
+	/* Just skip cr0 */
+	for (i = MAC_REG_CR1_SET; i < MAC_REG_CR0_CLR; i++) {
+		/* Clear */
+		writeb(~(*((u8 *) (context->mac_reg + i))), ptr + i + 4);
+		/* Set */
+		writeb(*((u8 *) (context->mac_reg + i)), ptr + i);
+	}
+
+	for (i = MAC_REG_MAR; i < MAC_REG_IMR; i += 4) {
+		writel(*((u32 *) (context->mac_reg + i)), ptr + i);
+	}
+
+	for (i = MAC_REG_RDBASE_LO; i < MAC_REG_FIFO_TEST0; i += 4) {
+		writel(*((u32 *) (context->mac_reg + i)), ptr + i);
+	}
+
+	for (i = MAC_REG_TDCSR_SET; i <= MAC_REG_RDCSR_SET; i++) {
+		writeb(*((u8 *) (context->mac_reg + i)), ptr + i);
+	}
+
+}
+
+/**
+ *	wol_calc_crc		-	WOL CRC
+ *	@pattern: data pattern
+ *	@mask_pattern: mask
+ *
+ *	Compute the wake on lan crc hashes for the packet header
+ *	we are interested in.
+ */
+
+static u16 wol_calc_crc(int size, u8 * pattern, u8 *mask_pattern)
+{
+	u16 crc = 0xFFFF;
+	u8 mask;
+	int i, j;
+
+	for (i = 0; i < size; i++) {
+		mask = mask_pattern[i];
+
+		/* Skip this loop if the mask equals to zero */
+		if (mask == 0x00)
+			continue;
+
+		for (j = 0; j < 8; j++) {
+			if ((mask & 0x01) == 0) {
+				mask >>= 1;
+				continue;
+			}
+			mask >>= 1;
+			crc = crc_ccitt(crc, &(pattern[i * 8 + j]), 1);
+		}
+	}
+	/*	Finally, invert the result once to get the correct data */
+	crc = ~crc;
+	return bitreverse(crc) >> 16;
+}
+
+/**
+ *	velocity_set_wol	-	set up for wake on lan
+ *	@vptr: velocity to set WOL status on
+ *
+ *	Set a card up for wake on lan either by unicast or by
+ *	ARP packet.
+ *
+ *	FIXME: check static buffer is safe here
+ */
+
+static int velocity_set_wol(struct velocity_info *vptr)
+{
+	struct mac_regs __iomem * regs = vptr->mac_regs;
+	static u8 buf[256];
+	int i;
+
+	static u32 mask_pattern[2][4] = {
+		{0x00203000, 0x000003C0, 0x00000000, 0x0000000}, /* ARP */
+		{0xfffff000, 0xffffffff, 0xffffffff, 0x000ffff}	 /* Magic Packet */
+	};
+
+	writew(0xFFFF, &regs->WOLCRClr);
+	writeb(WOLCFG_SAB | WOLCFG_SAM, &regs->WOLCFGSet);
+	writew(WOLCR_MAGIC_EN, &regs->WOLCRSet);
+
+	/*
+	   if (vptr->wol_opts & VELOCITY_WOL_PHY)
+	   writew((WOLCR_LINKON_EN|WOLCR_LINKOFF_EN), &regs->WOLCRSet);
+	 */
+
+	if (vptr->wol_opts & VELOCITY_WOL_UCAST) {
+		writew(WOLCR_UNICAST_EN, &regs->WOLCRSet);
+	}
+
+	if (vptr->wol_opts & VELOCITY_WOL_ARP) {
+		struct arp_packet *arp = (struct arp_packet *) buf;
+		u16 crc;
+		memset(buf, 0, sizeof(struct arp_packet) + 7);
+
+		for (i = 0; i < 4; i++)
+			writel(mask_pattern[0][i], &regs->ByteMask[0][i]);
+
+		arp->type = htons(ETH_P_ARP);
+		arp->ar_op = htons(1);
+
+		memcpy(arp->ar_tip, vptr->ip_addr, 4);
+
+		crc = wol_calc_crc((sizeof(struct arp_packet) + 7) / 8, buf,
+				(u8 *) & mask_pattern[0][0]);
+
+		writew(crc, &regs->PatternCRC[0]);
+		writew(WOLCR_ARP_EN, &regs->WOLCRSet);
+	}
+
+	BYTE_REG_BITS_ON(PWCFG_WOLTYPE, &regs->PWCFGSet);
+	BYTE_REG_BITS_ON(PWCFG_LEGACY_WOLEN, &regs->PWCFGSet);
+
+	writew(0x0FFF, &regs->WOLSRClr);
+
+	if (vptr->mii_status & VELOCITY_AUTONEG_ENABLE) {
+		if (PHYID_GET_PHY_ID(vptr->phy_id) == PHYID_CICADA_CS8201)
+			MII_REG_BITS_ON(AUXCR_MDPPS, MII_REG_AUXCR, vptr->mac_regs);
+
+		MII_REG_BITS_OFF(G1000CR_1000FD | G1000CR_1000, MII_REG_G1000CR, vptr->mac_regs);
+	}
+
+	if (vptr->mii_status & VELOCITY_SPEED_1000)
+		MII_REG_BITS_ON(BMCR_REAUTO, MII_REG_BMCR, vptr->mac_regs);
+
+	BYTE_REG_BITS_ON(CHIPGCR_FCMODE, &regs->CHIPGCR);
+
+	{
+		u8 GCR;
+		GCR = readb(&regs->CHIPGCR);
+		GCR = (GCR & ~CHIPGCR_FCGMII) | CHIPGCR_FCFDX;
+		writeb(GCR, &regs->CHIPGCR);
+	}
+
+	BYTE_REG_BITS_OFF(ISR_PWEI, &regs->ISR);
+	/* Turn on SWPTAG just before entering power mode */
+	BYTE_REG_BITS_ON(STICKHW_SWPTAG, &regs->STICKHW);
+	/* Go to bed ..... */
+	BYTE_REG_BITS_ON((STICKHW_DS1 | STICKHW_DS0), &regs->STICKHW);
+
+	return 0;
+}
+
+static int velocity_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+	struct net_device *dev = pci_get_drvdata(pdev);
+	struct velocity_info *vptr = netdev_priv(dev);
+	unsigned long flags;
+
+	if(!netif_running(vptr->dev))
+		return 0;
+
+	netif_device_detach(vptr->dev);
+
+	spin_lock_irqsave(&vptr->lock, flags);
+	pci_save_state(pdev);
+#ifdef ETHTOOL_GWOL
+	if (vptr->flags & VELOCITY_FLAGS_WOL_ENABLED) {
+		velocity_get_ip(vptr);
+		velocity_save_context(vptr, &vptr->context);
+		velocity_shutdown(vptr);
+		velocity_set_wol(vptr);
+		pci_enable_wake(pdev, 3, 1);
+		pci_set_power_state(pdev, PCI_D3hot);
+	} else {
+		velocity_save_context(vptr, &vptr->context);
+		velocity_shutdown(vptr);
+		pci_disable_device(pdev);
+		pci_set_power_state(pdev, pci_choose_state(pdev, state));
+	}
+#else
+	pci_set_power_state(pdev, pci_choose_state(pdev, state));
+#endif
+	spin_unlock_irqrestore(&vptr->lock, flags);
+	return 0;
+}
+
+static int velocity_resume(struct pci_dev *pdev)
+{
+	struct net_device *dev = pci_get_drvdata(pdev);
+	struct velocity_info *vptr = netdev_priv(dev);
+	unsigned long flags;
+	int i;
+
+	if(!netif_running(vptr->dev))
+		return 0;
+
+	pci_set_power_state(pdev, PCI_D0);
+	pci_enable_wake(pdev, 0, 0);
+	pci_restore_state(pdev);
+
+	mac_wol_reset(vptr->mac_regs);
+
+	spin_lock_irqsave(&vptr->lock, flags);
+	velocity_restore_context(vptr, &vptr->context);
+	velocity_init_registers(vptr, VELOCITY_INIT_WOL);
+	mac_disable_int(vptr->mac_regs);
+
+	velocity_tx_srv(vptr, 0);
+
+	for (i = 0; i < vptr->num_txq; i++) {
+		if (vptr->td_used[i]) {
+			mac_tx_queue_wake(vptr->mac_regs, i);
+		}
+	}
+
+	mac_enable_int(vptr->mac_regs);
+	spin_unlock_irqrestore(&vptr->lock, flags);
+	netif_device_attach(vptr->dev);
+
+	return 0;
+}
+
+static int velocity_netdev_event(struct notifier_block *nb, unsigned long notification, void *ptr)
+{
+	struct in_ifaddr *ifa = (struct in_ifaddr *) ptr;
+
+	if (ifa) {
+		struct net_device *dev = ifa->ifa_dev->dev;
+		struct velocity_info *vptr;
+		unsigned long flags;
+
+		spin_lock_irqsave(&velocity_dev_list_lock, flags);
+		list_for_each_entry(vptr, &velocity_dev_list, list) {
+			if (vptr->dev == dev) {
+				velocity_get_ip(vptr);
+				break;
+			}
+		}
+		spin_unlock_irqrestore(&velocity_dev_list_lock, flags);
+	}
+	return NOTIFY_DONE;
+}
+#endif