Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
diff --git a/drivers/pcmcia/sa1100_neponset.c b/drivers/pcmcia/sa1100_neponset.c
new file mode 100644
index 0000000..5e34b3e
--- /dev/null
+++ b/drivers/pcmcia/sa1100_neponset.c
@@ -0,0 +1,143 @@
+/*
+ * linux/drivers/pcmcia/sa1100_neponset.c
+ *
+ * Neponset PCMCIA specific routines
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/arch/neponset.h>
+#include <asm/hardware/sa1111.h>
+
+#include "sa1111_generic.h"
+
+/*
+ * Neponset uses the Maxim MAX1600, with the following connections:
+ *
+ *   MAX1600      Neponset
+ *
+ *    A0VCC        SA-1111 GPIO A<1>
+ *    A1VCC        SA-1111 GPIO A<0>
+ *    A0VPP        CPLD NCR A0VPP
+ *    A1VPP        CPLD NCR A1VPP
+ *    B0VCC        SA-1111 GPIO A<2>
+ *    B1VCC        SA-1111 GPIO A<3>
+ *    B0VPP        ground (slot B is CF)
+ *    B1VPP        ground (slot B is CF)
+ *
+ *     VX          VCC (5V)
+ *     VY          VCC3_3 (3.3V)
+ *     12INA       12V
+ *     12INB       ground (slot B is CF)
+ *
+ * The MAX1600 CODE pin is tied to ground, placing the device in 
+ * "Standard Intel code" mode. Refer to the Maxim data sheet for
+ * the corresponding truth table.
+ */
+
+static int
+neponset_pcmcia_configure_socket(struct soc_pcmcia_socket *skt, const socket_state_t *state)
+{
+	unsigned int ncr_mask, ncr_set, pa_dwr_mask, pa_dwr_set;
+	int ret;
+
+	switch (skt->nr) {
+	case 0:
+		pa_dwr_mask = GPIO_A0 | GPIO_A1;
+		ncr_mask = NCR_A0VPP | NCR_A1VPP;
+
+		if (state->Vpp == 0)
+			ncr_set = 0;
+		else if (state->Vpp == 120)
+			ncr_set = NCR_A1VPP;
+		else if (state->Vpp == state->Vcc)
+			ncr_set = NCR_A0VPP;
+		else {
+			printk(KERN_ERR "%s(): unrecognized VPP %u\n",
+			       __FUNCTION__, state->Vpp);
+			return -1;
+		}
+		break;
+
+	case 1:
+		pa_dwr_mask = GPIO_A2 | GPIO_A3;
+		ncr_mask = 0;
+		ncr_set = 0;
+
+		if (state->Vpp != state->Vcc && state->Vpp != 0) {
+			printk(KERN_ERR "%s(): CF slot cannot support VPP %u\n",
+			       __FUNCTION__, state->Vpp);
+			return -1;
+		}
+		break;
+
+	default:
+		return -1;
+	}
+
+	/*
+	 * pa_dwr_set is the mask for selecting Vcc on both sockets.
+	 * pa_dwr_mask selects which bits (and therefore socket) we change.
+	 */
+	switch (state->Vcc) {
+	default:
+	case 0:  pa_dwr_set = 0;		break;
+	case 33: pa_dwr_set = GPIO_A1|GPIO_A2;	break;
+	case 50: pa_dwr_set = GPIO_A0|GPIO_A3;	break;
+	}
+
+	ret = sa1111_pcmcia_configure_socket(skt, state);
+	if (ret == 0) {
+		unsigned long flags;
+
+		local_irq_save(flags);
+		NCR_0 = (NCR_0 & ~ncr_mask) | ncr_set;
+
+		local_irq_restore(flags);
+		sa1111_set_io(SA1111_DEV(skt->dev), pa_dwr_mask, pa_dwr_set);
+	}
+
+	return 0;
+}
+
+static void neponset_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
+{
+	if (skt->nr == 0)
+		NCR_0 &= ~(NCR_A0VPP | NCR_A1VPP);
+
+	sa1111_pcmcia_socket_init(skt);
+}
+
+static struct pcmcia_low_level neponset_pcmcia_ops = {
+	.owner			= THIS_MODULE,
+	.hw_init		= sa1111_pcmcia_hw_init,
+	.hw_shutdown		= sa1111_pcmcia_hw_shutdown,
+	.socket_state		= sa1111_pcmcia_socket_state,
+	.configure_socket	= neponset_pcmcia_configure_socket,
+	.socket_init		= neponset_pcmcia_socket_init,
+	.socket_suspend 	= sa1111_pcmcia_socket_suspend,
+};
+
+int __init pcmcia_neponset_init(struct sa1111_dev *sadev)
+{
+	int ret = -ENODEV;
+
+	if (machine_is_assabet()) {
+		/*
+		 * Set GPIO_A<3:0> to be outputs for the MAX1600,
+		 * and switch to standby mode.
+		 */
+		sa1111_set_io_dir(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0, 0);
+		sa1111_set_io(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0);
+		sa1111_set_sleep_io(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0);
+		ret = sa11xx_drv_pcmcia_probe(&sadev->dev, &neponset_pcmcia_ops, 0, 2);
+	}
+
+	return ret;
+}