Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/scsi/mac53c94.h b/drivers/scsi/mac53c94.h
new file mode 100644
index 0000000..1ad24e4
--- /dev/null
+++ b/drivers/scsi/mac53c94.h
@@ -0,0 +1,214 @@
+/*
+ * mac53c94.h: definitions for the driver for the 53c94 SCSI bus adaptor
+ * found on Power Macintosh computers, controlling the external SCSI chain.
+ *
+ * Copyright (C) 1996 Paul Mackerras.
+ */
+#ifndef _MAC53C94_H
+#define _MAC53C94_H
+
+/*
+ * Registers in the 53C94 controller.
+ */
+
+struct mac53c94_regs {
+ unsigned char count_lo;
+ char pad0[15];
+ unsigned char count_mid;
+ char pad1[15];
+ unsigned char fifo;
+ char pad2[15];
+ unsigned char command;
+ char pad3[15];
+ unsigned char status;
+ char pad4[15];
+ unsigned char interrupt;
+ char pad5[15];
+ unsigned char seqstep;
+ char pad6[15];
+ unsigned char flags;
+ char pad7[15];
+ unsigned char config1;
+ char pad8[15];
+ unsigned char clk_factor;
+ char pad9[15];
+ unsigned char test;
+ char pad10[15];
+ unsigned char config2;
+ char pad11[15];
+ unsigned char config3;
+ char pad12[15];
+ unsigned char config4;
+ char pad13[15];
+ unsigned char count_hi;
+ char pad14[15];
+ unsigned char fifo_res;
+ char pad15[15];
+};
+
+/*
+ * Alternate functions for some registers.
+ */
+#define dest_id status
+#define sel_timeout interrupt
+#define sync_period seqstep
+#define sync_offset flags
+
+/*
+ * Bits in command register.
+ */
+#define CMD_DMA_MODE 0x80
+#define CMD_MODE_MASK 0x70
+#define CMD_MODE_INIT 0x10
+#define CMD_MODE_TARG 0x20
+#define CMD_MODE_DISC 0x40
+
+#define CMD_NOP 0
+#define CMD_FLUSH 1
+#define CMD_RESET 2
+#define CMD_SCSI_RESET 3
+
+#define CMD_XFER_DATA 0x10
+#define CMD_I_COMPLETE 0x11
+#define CMD_ACCEPT_MSG 0x12
+#define CMD_XFER_PAD 0x18
+#define CMD_SET_ATN 0x1a
+#define CMD_CLR_ATN 0x1b
+
+#define CMD_SEND_MSG 0x20
+#define CMD_SEND_STATUS 0x21
+#define CMD_SEND_DATA 0x22
+#define CMD_DISC_SEQ 0x23
+#define CMD_TERMINATE 0x24
+#define CMD_T_COMPLETE 0x25
+#define CMD_DISCONNECT 0x27
+#define CMD_RECV_MSG 0x28
+#define CMD_RECV_CDB 0x29
+#define CMD_RECV_DATA 0x2a
+#define CMD_RECV_CMD 0x2b
+#define CMD_ABORT_DMA 0x04
+
+#define CMD_RESELECT 0x40
+#define CMD_SELECT 0x41
+#define CMD_SELECT_ATN 0x42
+#define CMD_SELATN_STOP 0x43
+#define CMD_ENABLE_SEL 0x44
+#define CMD_DISABLE_SEL 0x45
+#define CMD_SEL_ATN3 0x46
+#define CMD_RESEL_ATN3 0x47
+
+/*
+ * Bits in status register.
+ */
+#define STAT_IRQ 0x80
+#define STAT_ERROR 0x40
+#define STAT_PARITY 0x20
+#define STAT_TC_ZERO 0x10
+#define STAT_DONE 0x08
+#define STAT_PHASE 0x07
+#define STAT_MSG 0x04
+#define STAT_CD 0x02
+#define STAT_IO 0x01
+
+/*
+ * Bits in interrupt register.
+ */
+#define INTR_RESET 0x80 /* SCSI bus was reset */
+#define INTR_ILL_CMD 0x40 /* illegal command */
+#define INTR_DISCONNECT 0x20 /* we got disconnected */
+#define INTR_BUS_SERV 0x10 /* bus service requested */
+#define INTR_DONE 0x08 /* function completed */
+#define INTR_RESELECTED 0x04 /* we were reselected */
+#define INTR_SEL_ATN 0x02 /* we were selected, ATN asserted */
+#define INTR_SELECT 0x01 /* we were selected, ATN negated */
+
+/*
+ * Encoding for the select timeout.
+ */
+#define TIMO_VAL(x) ((x) * 5000 / 7682)
+
+/*
+ * Bits in sequence step register.
+ */
+#define SS_MASK 7
+#define SS_ARB_SEL 0 /* Selection & arbitration complete */
+#define SS_MSG_SENT 1 /* One message byte sent */
+#define SS_NOT_CMD 2 /* Not in command phase */
+#define SS_PHASE_CHG 3 /* Early phase change, cmd bytes lost */
+#define SS_DONE 4 /* Command was sent OK */
+
+/*
+ * Encoding for sync transfer period.
+ */
+#define SYNCP_MASK 0x1f
+#define SYNCP_MIN 4
+#define SYNCP_MAX 31
+
+/*
+ * Bits in flags register.
+ */
+#define FLAGS_FIFO_LEV 0x1f
+#define FLAGS_SEQ_STEP 0xe0
+
+/*
+ * Encoding for sync offset.
+ */
+#define SYNCO_MASK 0x0f
+#define SYNCO_ASS_CTRL 0x30 /* REQ/ACK assertion control */
+#define SYNCO_NEG_CTRL 0xc0 /* REQ/ACK negation control */
+
+/*
+ * Bits in config1 register.
+ */
+#define CF1_SLOW_CABLE 0x80 /* Slow cable mode */
+#define CF1_NO_RES_REP 0x40 /* Disable SCSI reset reports */
+#define CF1_PAR_TEST 0x20 /* Parity test mode enable */
+#define CF1_PAR_ENABLE 0x10 /* Enable parity checks */
+#define CF1_TEST 0x08 /* Chip tests */
+#define CF1_MY_ID 0x07 /* Controller's address on bus */
+
+/*
+ * Encoding for clk_factor register.
+ */
+#define CLKF_MASK 7
+#define CLKF_VAL(freq) ((((freq) + 4999999) / 5000000) & CLKF_MASK)
+
+/*
+ * Bits in test mode register.
+ */
+#define TEST_TARGET 1 /* target test mode */
+#define TEST_INITIATOR 2 /* initiator test mode */
+#define TEST_TRISTATE 4 /* tristate (hi-z) test mode */
+
+/*
+ * Bits in config2 register.
+ */
+#define CF2_RFB 0x80
+#define CF2_FEATURE_EN 0x40 /* enable features / phase latch */
+#define CF2_BYTECTRL 0x20
+#define CF2_DREQ_HIZ 0x10
+#define CF2_SCSI2 0x08
+#define CF2_PAR_ABORT 0x04 /* bad parity target abort */
+#define CF2_REG_PARERR 0x02 /* register parity error */
+#define CF2_DMA_PARERR 0x01 /* DMA parity error */
+
+/*
+ * Bits in the config3 register.
+ */
+#define CF3_ID_MSG_CHK 0x80
+#define CF3_3B_MSGS 0x40
+#define CF3_CDB10 0x20
+#define CF3_FASTSCSI 0x10 /* enable fast SCSI support */
+#define CF3_FASTCLOCK 0x08
+#define CF3_SAVERESID 0x04
+#define CF3_ALT_DMA 0x02
+#define CF3_THRESH_8 0x01
+
+/*
+ * Bits in the config4 register.
+ */
+#define CF4_EAN 0x04
+#define CF4_TEST 0x02
+#define CF4_BBTE 0x01
+
+#endif /* _MAC53C94_H */