Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/serial/serial_txx9.c b/drivers/serial/serial_txx9.c
new file mode 100644
index 0000000..dfc9873
--- /dev/null
+++ b/drivers/serial/serial_txx9.c
@@ -0,0 +1,1171 @@
+/*
+ * drivers/serial/serial_txx9.c
+ *
+ * Derived from many drivers using generic_serial interface,
+ * especially serial_tx3912.c by Steven J. Hill and r39xx_serial.c
+ * (was in Linux/VR tree) by Jim Pick.
+ *
+ * Copyright (C) 1999 Harald Koerfgen
+ * Copyright (C) 2000 Jim Pick <jim@jimpick.com>
+ * Copyright (C) 2001 Steven J. Hill (sjhill@realitydiluted.com)
+ * Copyright (C) 2000-2002 Toshiba Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Serial driver for TX3927/TX4927/TX4925/TX4938 internal SIO controller
+ *
+ * Revision History:
+ * 0.30 Initial revision. (Renamed from serial_txx927.c)
+ * 0.31 Use save_flags instead of local_irq_save.
+ * 0.32 Support SCLK.
+ * 0.33 Switch TXX9_TTY_NAME by CONFIG_SERIAL_TXX9_STDSERIAL.
+ * Support TIOCSERGETLSR.
+ * 0.34 Support slow baudrate.
+ * 0.40 Merge codes from mainstream kernel (2.4.22).
+ * 0.41 Fix console checking in rs_shutdown_port().
+ * Disable flow-control in serial_console_write().
+ * 0.42 Fix minor compiler warning.
+ * 1.00 Kernel 2.6. Converted to new serial core (based on 8250.c).
+ * 1.01 Set fifosize to make tx_empry called properly.
+ * Use standard uart_get_divisor.
+ * 1.02 Cleanup. (import 8250.c changes)
+ */
+#include <linux/config.h>
+
+#if defined(CONFIG_SERIAL_TXX9_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/pci.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+
+static char *serial_version = "1.02";
+static char *serial_name = "TX39/49 Serial driver";
+
+#define PASS_LIMIT 256
+
+#if !defined(CONFIG_SERIAL_TXX9_STDSERIAL)
+/* "ttyS" is used for standard serial driver */
+#define TXX9_TTY_NAME "ttyTX"
+#define TXX9_TTY_DEVFS_NAME "tttx/"
+#define TXX9_TTY_MINOR_START (64 + 64) /* ttyTX0(128), ttyTX1(129) */
+#else
+/* acts like standard serial driver */
+#define TXX9_TTY_NAME "ttyS"
+#define TXX9_TTY_DEVFS_NAME "tts/"
+#define TXX9_TTY_MINOR_START 64
+#endif
+#define TXX9_TTY_MAJOR TTY_MAJOR
+
+/* flag aliases */
+#define UPF_TXX9_HAVE_CTS_LINE UPF_BUGGY_UART
+#define UPF_TXX9_USE_SCLK UPF_MAGIC_MULTIPLIER
+
+#ifdef CONFIG_PCI
+/* support for Toshiba TC86C001 SIO */
+#define ENABLE_SERIAL_TXX9_PCI
+#endif
+
+/*
+ * Number of serial ports
+ */
+#ifdef ENABLE_SERIAL_TXX9_PCI
+#define NR_PCI_BOARDS 4
+#define UART_NR (2 + NR_PCI_BOARDS)
+#else
+#define UART_NR 2
+#endif
+
+struct uart_txx9_port {
+ struct uart_port port;
+
+ /*
+ * We provide a per-port pm hook.
+ */
+ void (*pm)(struct uart_port *port,
+ unsigned int state, unsigned int old);
+};
+
+#define TXX9_REGION_SIZE 0x24
+
+/* TXX9 Serial Registers */
+#define TXX9_SILCR 0x00
+#define TXX9_SIDICR 0x04
+#define TXX9_SIDISR 0x08
+#define TXX9_SICISR 0x0c
+#define TXX9_SIFCR 0x10
+#define TXX9_SIFLCR 0x14
+#define TXX9_SIBGR 0x18
+#define TXX9_SITFIFO 0x1c
+#define TXX9_SIRFIFO 0x20
+
+/* SILCR : Line Control */
+#define TXX9_SILCR_SCS_MASK 0x00000060
+#define TXX9_SILCR_SCS_IMCLK 0x00000000
+#define TXX9_SILCR_SCS_IMCLK_BG 0x00000020
+#define TXX9_SILCR_SCS_SCLK 0x00000040
+#define TXX9_SILCR_SCS_SCLK_BG 0x00000060
+#define TXX9_SILCR_UEPS 0x00000010
+#define TXX9_SILCR_UPEN 0x00000008
+#define TXX9_SILCR_USBL_MASK 0x00000004
+#define TXX9_SILCR_USBL_1BIT 0x00000000
+#define TXX9_SILCR_USBL_2BIT 0x00000004
+#define TXX9_SILCR_UMODE_MASK 0x00000003
+#define TXX9_SILCR_UMODE_8BIT 0x00000000
+#define TXX9_SILCR_UMODE_7BIT 0x00000001
+
+/* SIDICR : DMA/Int. Control */
+#define TXX9_SIDICR_TDE 0x00008000
+#define TXX9_SIDICR_RDE 0x00004000
+#define TXX9_SIDICR_TIE 0x00002000
+#define TXX9_SIDICR_RIE 0x00001000
+#define TXX9_SIDICR_SPIE 0x00000800
+#define TXX9_SIDICR_CTSAC 0x00000600
+#define TXX9_SIDICR_STIE_MASK 0x0000003f
+#define TXX9_SIDICR_STIE_OERS 0x00000020
+#define TXX9_SIDICR_STIE_CTSS 0x00000010
+#define TXX9_SIDICR_STIE_RBRKD 0x00000008
+#define TXX9_SIDICR_STIE_TRDY 0x00000004
+#define TXX9_SIDICR_STIE_TXALS 0x00000002
+#define TXX9_SIDICR_STIE_UBRKD 0x00000001
+
+/* SIDISR : DMA/Int. Status */
+#define TXX9_SIDISR_UBRK 0x00008000
+#define TXX9_SIDISR_UVALID 0x00004000
+#define TXX9_SIDISR_UFER 0x00002000
+#define TXX9_SIDISR_UPER 0x00001000
+#define TXX9_SIDISR_UOER 0x00000800
+#define TXX9_SIDISR_ERI 0x00000400
+#define TXX9_SIDISR_TOUT 0x00000200
+#define TXX9_SIDISR_TDIS 0x00000100
+#define TXX9_SIDISR_RDIS 0x00000080
+#define TXX9_SIDISR_STIS 0x00000040
+#define TXX9_SIDISR_RFDN_MASK 0x0000001f
+
+/* SICISR : Change Int. Status */
+#define TXX9_SICISR_OERS 0x00000020
+#define TXX9_SICISR_CTSS 0x00000010
+#define TXX9_SICISR_RBRKD 0x00000008
+#define TXX9_SICISR_TRDY 0x00000004
+#define TXX9_SICISR_TXALS 0x00000002
+#define TXX9_SICISR_UBRKD 0x00000001
+
+/* SIFCR : FIFO Control */
+#define TXX9_SIFCR_SWRST 0x00008000
+#define TXX9_SIFCR_RDIL_MASK 0x00000180
+#define TXX9_SIFCR_RDIL_1 0x00000000
+#define TXX9_SIFCR_RDIL_4 0x00000080
+#define TXX9_SIFCR_RDIL_8 0x00000100
+#define TXX9_SIFCR_RDIL_12 0x00000180
+#define TXX9_SIFCR_RDIL_MAX 0x00000180
+#define TXX9_SIFCR_TDIL_MASK 0x00000018
+#define TXX9_SIFCR_TDIL_MASK 0x00000018
+#define TXX9_SIFCR_TDIL_1 0x00000000
+#define TXX9_SIFCR_TDIL_4 0x00000001
+#define TXX9_SIFCR_TDIL_8 0x00000010
+#define TXX9_SIFCR_TDIL_MAX 0x00000010
+#define TXX9_SIFCR_TFRST 0x00000004
+#define TXX9_SIFCR_RFRST 0x00000002
+#define TXX9_SIFCR_FRSTE 0x00000001
+#define TXX9_SIO_TX_FIFO 8
+#define TXX9_SIO_RX_FIFO 16
+
+/* SIFLCR : Flow Control */
+#define TXX9_SIFLCR_RCS 0x00001000
+#define TXX9_SIFLCR_TES 0x00000800
+#define TXX9_SIFLCR_RTSSC 0x00000200
+#define TXX9_SIFLCR_RSDE 0x00000100
+#define TXX9_SIFLCR_TSDE 0x00000080
+#define TXX9_SIFLCR_RTSTL_MASK 0x0000001e
+#define TXX9_SIFLCR_RTSTL_MAX 0x0000001e
+#define TXX9_SIFLCR_TBRK 0x00000001
+
+/* SIBGR : Baudrate Control */
+#define TXX9_SIBGR_BCLK_MASK 0x00000300
+#define TXX9_SIBGR_BCLK_T0 0x00000000
+#define TXX9_SIBGR_BCLK_T2 0x00000100
+#define TXX9_SIBGR_BCLK_T4 0x00000200
+#define TXX9_SIBGR_BCLK_T6 0x00000300
+#define TXX9_SIBGR_BRD_MASK 0x000000ff
+
+static inline unsigned int sio_in(struct uart_txx9_port *up, int offset)
+{
+ switch (up->port.iotype) {
+ default:
+ return *(volatile u32 *)(up->port.membase + offset);
+ case UPIO_PORT:
+ return inl(up->port.iobase + offset);
+ }
+}
+
+static inline void
+sio_out(struct uart_txx9_port *up, int offset, int value)
+{
+ switch (up->port.iotype) {
+ default:
+ *(volatile u32 *)(up->port.membase + offset) = value;
+ break;
+ case UPIO_PORT:
+ outl(value, up->port.iobase + offset);
+ break;
+ }
+}
+
+static inline void
+sio_mask(struct uart_txx9_port *up, int offset, unsigned int value)
+{
+ sio_out(up, offset, sio_in(up, offset) & ~value);
+}
+static inline void
+sio_set(struct uart_txx9_port *up, int offset, unsigned int value)
+{
+ sio_out(up, offset, sio_in(up, offset) | value);
+}
+
+static inline void
+sio_quot_set(struct uart_txx9_port *up, int quot)
+{
+ quot >>= 1;
+ if (quot < 256)
+ sio_out(up, TXX9_SIBGR, quot | TXX9_SIBGR_BCLK_T0);
+ else if (quot < (256 << 2))
+ sio_out(up, TXX9_SIBGR, (quot >> 2) | TXX9_SIBGR_BCLK_T2);
+ else if (quot < (256 << 4))
+ sio_out(up, TXX9_SIBGR, (quot >> 4) | TXX9_SIBGR_BCLK_T4);
+ else if (quot < (256 << 6))
+ sio_out(up, TXX9_SIBGR, (quot >> 6) | TXX9_SIBGR_BCLK_T6);
+ else
+ sio_out(up, TXX9_SIBGR, 0xff | TXX9_SIBGR_BCLK_T6);
+}
+
+static void serial_txx9_stop_tx(struct uart_port *port, unsigned int tty_stop)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ unsigned long flags;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static void serial_txx9_start_tx(struct uart_port *port, unsigned int tty_start)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ unsigned long flags;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ sio_set(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static void serial_txx9_stop_rx(struct uart_port *port)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ unsigned long flags;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ up->port.read_status_mask &= ~TXX9_SIDISR_RDIS;
+#if 0
+ sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_RIE);
+#endif
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static void serial_txx9_enable_ms(struct uart_port *port)
+{
+ /* TXX9-SIO can not control DTR... */
+}
+
+static inline void
+receive_chars(struct uart_txx9_port *up, unsigned int *status, struct pt_regs *regs)
+{
+ struct tty_struct *tty = up->port.info->tty;
+ unsigned char ch;
+ unsigned int disr = *status;
+ int max_count = 256;
+ char flag;
+
+ do {
+ /* The following is not allowed by the tty layer and
+ unsafe. It should be fixed ASAP */
+ if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) {
+ if(tty->low_latency)
+ tty_flip_buffer_push(tty);
+ /* If this failed then we will throw away the
+ bytes but must do so to clear interrupts */
+ }
+ ch = sio_in(up, TXX9_SIRFIFO);
+ flag = TTY_NORMAL;
+ up->port.icount.rx++;
+
+ if (unlikely(disr & (TXX9_SIDISR_UBRK | TXX9_SIDISR_UPER |
+ TXX9_SIDISR_UFER | TXX9_SIDISR_UOER))) {
+ /*
+ * For statistics only
+ */
+ if (disr & TXX9_SIDISR_UBRK) {
+ disr &= ~(TXX9_SIDISR_UFER | TXX9_SIDISR_UPER);
+ up->port.icount.brk++;
+ /*
+ * We do the SysRQ and SAK checking
+ * here because otherwise the break
+ * may get masked by ignore_status_mask
+ * or read_status_mask.
+ */
+ if (uart_handle_break(&up->port))
+ goto ignore_char;
+ } else if (disr & TXX9_SIDISR_UPER)
+ up->port.icount.parity++;
+ else if (disr & TXX9_SIDISR_UFER)
+ up->port.icount.frame++;
+ if (disr & TXX9_SIDISR_UOER)
+ up->port.icount.overrun++;
+
+ /*
+ * Mask off conditions which should be ingored.
+ */
+ disr &= up->port.read_status_mask;
+
+ if (disr & TXX9_SIDISR_UBRK) {
+ flag = TTY_BREAK;
+ } else if (disr & TXX9_SIDISR_UPER)
+ flag = TTY_PARITY;
+ else if (disr & TXX9_SIDISR_UFER)
+ flag = TTY_FRAME;
+ }
+ if (uart_handle_sysrq_char(&up->port, ch, regs))
+ goto ignore_char;
+ if ((disr & up->port.ignore_status_mask) == 0) {
+ tty_insert_flip_char(tty, ch, flag);
+ }
+ if ((disr & TXX9_SIDISR_UOER) &&
+ tty->flip.count < TTY_FLIPBUF_SIZE) {
+ /*
+ * Overrun is special, since it's reported
+ * immediately, and doesn't affect the current
+ * character.
+ */
+ tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+ }
+ ignore_char:
+ disr = sio_in(up, TXX9_SIDISR);
+ } while (!(disr & TXX9_SIDISR_UVALID) && (max_count-- > 0));
+ tty_flip_buffer_push(tty);
+ *status = disr;
+}
+
+static inline void transmit_chars(struct uart_txx9_port *up)
+{
+ struct circ_buf *xmit = &up->port.info->xmit;
+ int count;
+
+ if (up->port.x_char) {
+ sio_out(up, TXX9_SITFIFO, up->port.x_char);
+ up->port.icount.tx++;
+ up->port.x_char = 0;
+ return;
+ }
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
+ serial_txx9_stop_tx(&up->port, 0);
+ return;
+ }
+
+ count = TXX9_SIO_TX_FIFO;
+ do {
+ sio_out(up, TXX9_SITFIFO, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ up->port.icount.tx++;
+ if (uart_circ_empty(xmit))
+ break;
+ } while (--count > 0);
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&up->port);
+
+ if (uart_circ_empty(xmit))
+ serial_txx9_stop_tx(&up->port, 0);
+}
+
+static irqreturn_t serial_txx9_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+ int pass_counter = 0;
+ struct uart_txx9_port *up = dev_id;
+ unsigned int status;
+
+ while (1) {
+ spin_lock(&up->port.lock);
+ status = sio_in(up, TXX9_SIDISR);
+ if (!(sio_in(up, TXX9_SIDICR) & TXX9_SIDICR_TIE))
+ status &= ~TXX9_SIDISR_TDIS;
+ if (!(status & (TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
+ TXX9_SIDISR_TOUT))) {
+ spin_unlock(&up->port.lock);
+ break;
+ }
+
+ if (status & TXX9_SIDISR_RDIS)
+ receive_chars(up, &status, regs);
+ if (status & TXX9_SIDISR_TDIS)
+ transmit_chars(up);
+ /* Clear TX/RX Int. Status */
+ sio_mask(up, TXX9_SIDISR,
+ TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
+ TXX9_SIDISR_TOUT);
+ spin_unlock(&up->port.lock);
+
+ if (pass_counter++ > PASS_LIMIT)
+ break;
+ }
+
+ return pass_counter ? IRQ_HANDLED : IRQ_NONE;
+}
+
+static unsigned int serial_txx9_tx_empty(struct uart_port *port)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ unsigned long flags;
+ unsigned int ret;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ ret = (sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS) ? TIOCSER_TEMT : 0;
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ return ret;
+}
+
+static unsigned int serial_txx9_get_mctrl(struct uart_port *port)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ unsigned long flags;
+ unsigned int ret;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ ret = ((sio_in(up, TXX9_SIFLCR) & TXX9_SIFLCR_RTSSC) ? 0 : TIOCM_RTS)
+ | ((sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS) ? 0 : TIOCM_CTS);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ return ret;
+}
+
+static void serial_txx9_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ unsigned long flags;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ if (mctrl & TIOCM_RTS)
+ sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
+ else
+ sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static void serial_txx9_break_ctl(struct uart_port *port, int break_state)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ unsigned long flags;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ if (break_state == -1)
+ sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
+ else
+ sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static int serial_txx9_startup(struct uart_port *port)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ unsigned long flags;
+ int retval;
+
+ /*
+ * Clear the FIFO buffers and disable them.
+ * (they will be reeanbled in set_termios())
+ */
+ sio_set(up, TXX9_SIFCR,
+ TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
+ /* clear reset */
+ sio_mask(up, TXX9_SIFCR,
+ TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
+ sio_out(up, TXX9_SIDICR, 0);
+
+ /*
+ * Clear the interrupt registers.
+ */
+ sio_out(up, TXX9_SIDISR, 0);
+
+ retval = request_irq(up->port.irq, serial_txx9_interrupt,
+ SA_SHIRQ, "serial_txx9", up);
+ if (retval)
+ return retval;
+
+ /*
+ * Now, initialize the UART
+ */
+ spin_lock_irqsave(&up->port.lock, flags);
+ serial_txx9_set_mctrl(&up->port, up->port.mctrl);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ /* Enable RX/TX */
+ sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
+
+ /*
+ * Finally, enable interrupts.
+ */
+ sio_set(up, TXX9_SIDICR, TXX9_SIDICR_RIE);
+
+ return 0;
+}
+
+static void serial_txx9_shutdown(struct uart_port *port)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ unsigned long flags;
+
+ /*
+ * Disable interrupts from this port
+ */
+ sio_out(up, TXX9_SIDICR, 0); /* disable all intrs */
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ serial_txx9_set_mctrl(&up->port, up->port.mctrl);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ /*
+ * Disable break condition
+ */
+ sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
+
+#ifdef CONFIG_SERIAL_TXX9_CONSOLE
+ if (up->port.cons && up->port.line == up->port.cons->index) {
+ free_irq(up->port.irq, up);
+ return;
+ }
+#endif
+ /* reset FIFOs */
+ sio_set(up, TXX9_SIFCR,
+ TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
+ /* clear reset */
+ sio_mask(up, TXX9_SIFCR,
+ TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
+
+ /* Disable RX/TX */
+ sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
+
+ free_irq(up->port.irq, up);
+}
+
+static void
+serial_txx9_set_termios(struct uart_port *port, struct termios *termios,
+ struct termios *old)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ unsigned int cval, fcr = 0;
+ unsigned long flags;
+ unsigned int baud, quot;
+
+ cval = sio_in(up, TXX9_SILCR);
+ /* byte size and parity */
+ cval &= ~TXX9_SILCR_UMODE_MASK;
+ switch (termios->c_cflag & CSIZE) {
+ case CS7:
+ cval |= TXX9_SILCR_UMODE_7BIT;
+ break;
+ default:
+ case CS5: /* not supported */
+ case CS6: /* not supported */
+ case CS8:
+ cval |= TXX9_SILCR_UMODE_8BIT;
+ break;
+ }
+
+ cval &= ~TXX9_SILCR_USBL_MASK;
+ if (termios->c_cflag & CSTOPB)
+ cval |= TXX9_SILCR_USBL_2BIT;
+ else
+ cval |= TXX9_SILCR_USBL_1BIT;
+ cval &= ~(TXX9_SILCR_UPEN | TXX9_SILCR_UEPS);
+ if (termios->c_cflag & PARENB)
+ cval |= TXX9_SILCR_UPEN;
+ if (!(termios->c_cflag & PARODD))
+ cval |= TXX9_SILCR_UEPS;
+
+ /*
+ * Ask the core to calculate the divisor for us.
+ */
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16/2);
+ quot = uart_get_divisor(port, baud);
+
+ /* Set up FIFOs */
+ /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
+ fcr = TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1;
+
+ /*
+ * Ok, we're now changing the port state. Do it with
+ * interrupts disabled.
+ */
+ spin_lock_irqsave(&up->port.lock, flags);
+
+ /*
+ * Update the per-port timeout.
+ */
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ up->port.read_status_mask = TXX9_SIDISR_UOER |
+ TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS;
+ if (termios->c_iflag & INPCK)
+ up->port.read_status_mask |= TXX9_SIDISR_UFER | TXX9_SIDISR_UPER;
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ up->port.read_status_mask |= TXX9_SIDISR_UBRK;
+
+ /*
+ * Characteres to ignore
+ */
+ up->port.ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ up->port.ignore_status_mask |= TXX9_SIDISR_UPER | TXX9_SIDISR_UFER;
+ if (termios->c_iflag & IGNBRK) {
+ up->port.ignore_status_mask |= TXX9_SIDISR_UBRK;
+ /*
+ * If we're ignoring parity and break indicators,
+ * ignore overruns too (for real raw support).
+ */
+ if (termios->c_iflag & IGNPAR)
+ up->port.ignore_status_mask |= TXX9_SIDISR_UOER;
+ }
+
+ /*
+ * ignore all characters if CREAD is not set
+ */
+ if ((termios->c_cflag & CREAD) == 0)
+ up->port.ignore_status_mask |= TXX9_SIDISR_RDIS;
+
+ /* CTS flow control flag */
+ if ((termios->c_cflag & CRTSCTS) &&
+ (up->port.flags & UPF_TXX9_HAVE_CTS_LINE)) {
+ sio_set(up, TXX9_SIFLCR,
+ TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
+ } else {
+ sio_mask(up, TXX9_SIFLCR,
+ TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
+ }
+
+ sio_out(up, TXX9_SILCR, cval);
+ sio_quot_set(up, quot);
+ sio_out(up, TXX9_SIFCR, fcr);
+
+ serial_txx9_set_mctrl(&up->port, up->port.mctrl);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static void
+serial_txx9_pm(struct uart_port *port, unsigned int state,
+ unsigned int oldstate)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ if (state) {
+ /* sleep */
+
+ if (up->pm)
+ up->pm(port, state, oldstate);
+ } else {
+ /* wake */
+
+ if (up->pm)
+ up->pm(port, state, oldstate);
+ }
+}
+
+static int serial_txx9_request_resource(struct uart_txx9_port *up)
+{
+ unsigned int size = TXX9_REGION_SIZE;
+ int ret = 0;
+
+ switch (up->port.iotype) {
+ default:
+ if (!up->port.mapbase)
+ break;
+
+ if (!request_mem_region(up->port.mapbase, size, "serial_txx9")) {
+ ret = -EBUSY;
+ break;
+ }
+
+ if (up->port.flags & UPF_IOREMAP) {
+ up->port.membase = ioremap(up->port.mapbase, size);
+ if (!up->port.membase) {
+ release_mem_region(up->port.mapbase, size);
+ ret = -ENOMEM;
+ }
+ }
+ break;
+
+ case UPIO_PORT:
+ if (!request_region(up->port.iobase, size, "serial_txx9"))
+ ret = -EBUSY;
+ break;
+ }
+ return ret;
+}
+
+static void serial_txx9_release_resource(struct uart_txx9_port *up)
+{
+ unsigned int size = TXX9_REGION_SIZE;
+
+ switch (up->port.iotype) {
+ default:
+ if (!up->port.mapbase)
+ break;
+
+ if (up->port.flags & UPF_IOREMAP) {
+ iounmap(up->port.membase);
+ up->port.membase = NULL;
+ }
+
+ release_mem_region(up->port.mapbase, size);
+ break;
+
+ case UPIO_PORT:
+ release_region(up->port.iobase, size);
+ break;
+ }
+}
+
+static void serial_txx9_release_port(struct uart_port *port)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ serial_txx9_release_resource(up);
+}
+
+static int serial_txx9_request_port(struct uart_port *port)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ return serial_txx9_request_resource(up);
+}
+
+static void serial_txx9_config_port(struct uart_port *port, int uflags)
+{
+ struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ unsigned long flags;
+ int ret;
+
+ /*
+ * Find the region that we can probe for. This in turn
+ * tells us whether we can probe for the type of port.
+ */
+ ret = serial_txx9_request_resource(up);
+ if (ret < 0)
+ return;
+ port->type = PORT_TXX9;
+ up->port.fifosize = TXX9_SIO_TX_FIFO;
+
+#ifdef CONFIG_SERIAL_TXX9_CONSOLE
+ if (up->port.line == up->port.cons->index)
+ return;
+#endif
+ spin_lock_irqsave(&up->port.lock, flags);
+ /*
+ * Reset the UART.
+ */
+ sio_out(up, TXX9_SIFCR, TXX9_SIFCR_SWRST);
+#ifdef CONFIG_CPU_TX49XX
+ /* TX4925 BUG WORKAROUND. Accessing SIOC register
+ * immediately after soft reset causes bus error. */
+ iob();
+ udelay(1);
+#endif
+ while (sio_in(up, TXX9_SIFCR) & TXX9_SIFCR_SWRST)
+ ;
+ /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
+ sio_set(up, TXX9_SIFCR,
+ TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1);
+ /* initial settings */
+ sio_out(up, TXX9_SILCR,
+ TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
+ ((up->port.flags & UPF_TXX9_USE_SCLK) ?
+ TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
+ sio_quot_set(up, uart_get_divisor(port, 9600));
+ sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static int
+serial_txx9_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ if (ser->irq < 0 ||
+ ser->baud_base < 9600 || ser->type != PORT_TXX9)
+ return -EINVAL;
+ return 0;
+}
+
+static const char *
+serial_txx9_type(struct uart_port *port)
+{
+ return "txx9";
+}
+
+static struct uart_ops serial_txx9_pops = {
+ .tx_empty = serial_txx9_tx_empty,
+ .set_mctrl = serial_txx9_set_mctrl,
+ .get_mctrl = serial_txx9_get_mctrl,
+ .stop_tx = serial_txx9_stop_tx,
+ .start_tx = serial_txx9_start_tx,
+ .stop_rx = serial_txx9_stop_rx,
+ .enable_ms = serial_txx9_enable_ms,
+ .break_ctl = serial_txx9_break_ctl,
+ .startup = serial_txx9_startup,
+ .shutdown = serial_txx9_shutdown,
+ .set_termios = serial_txx9_set_termios,
+ .pm = serial_txx9_pm,
+ .type = serial_txx9_type,
+ .release_port = serial_txx9_release_port,
+ .request_port = serial_txx9_request_port,
+ .config_port = serial_txx9_config_port,
+ .verify_port = serial_txx9_verify_port,
+};
+
+static struct uart_txx9_port serial_txx9_ports[UART_NR];
+
+static void __init serial_txx9_register_ports(struct uart_driver *drv)
+{
+ int i;
+
+ for (i = 0; i < UART_NR; i++) {
+ struct uart_txx9_port *up = &serial_txx9_ports[i];
+
+ up->port.line = i;
+ up->port.ops = &serial_txx9_pops;
+ uart_add_one_port(drv, &up->port);
+ }
+}
+
+#ifdef CONFIG_SERIAL_TXX9_CONSOLE
+
+/*
+ * Wait for transmitter & holding register to empty
+ */
+static inline void wait_for_xmitr(struct uart_txx9_port *up)
+{
+ unsigned int tmout = 10000;
+
+ /* Wait up to 10ms for the character(s) to be sent. */
+ while (--tmout &&
+ !(sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS))
+ udelay(1);
+
+ /* Wait up to 1s for flow control if necessary */
+ if (up->port.flags & UPF_CONS_FLOW) {
+ tmout = 1000000;
+ while (--tmout &&
+ (sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS))
+ udelay(1);
+ }
+}
+
+/*
+ * Print a string to the serial port trying not to disturb
+ * any possible real use of the port...
+ *
+ * The console_lock must be held when we get here.
+ */
+static void
+serial_txx9_console_write(struct console *co, const char *s, unsigned int count)
+{
+ struct uart_txx9_port *up = &serial_txx9_ports[co->index];
+ unsigned int ier, flcr;
+ int i;
+
+ /*
+ * First save the UER then disable the interrupts
+ */
+ ier = sio_in(up, TXX9_SIDICR);
+ sio_out(up, TXX9_SIDICR, 0);
+ /*
+ * Disable flow-control if enabled (and unnecessary)
+ */
+ flcr = sio_in(up, TXX9_SIFLCR);
+ if (!(up->port.flags & UPF_CONS_FLOW) && (flcr & TXX9_SIFLCR_TES))
+ sio_out(up, TXX9_SIFLCR, flcr & ~TXX9_SIFLCR_TES);
+
+ /*
+ * Now, do each character
+ */
+ for (i = 0; i < count; i++, s++) {
+ wait_for_xmitr(up);
+
+ /*
+ * Send the character out.
+ * If a LF, also do CR...
+ */
+ sio_out(up, TXX9_SITFIFO, *s);
+ if (*s == 10) {
+ wait_for_xmitr(up);
+ sio_out(up, TXX9_SITFIFO, 13);
+ }
+ }
+
+ /*
+ * Finally, wait for transmitter to become empty
+ * and restore the IER
+ */
+ wait_for_xmitr(up);
+ sio_out(up, TXX9_SIFLCR, flcr);
+ sio_out(up, TXX9_SIDICR, ier);
+}
+
+static int serial_txx9_console_setup(struct console *co, char *options)
+{
+ struct uart_port *port;
+ struct uart_txx9_port *up;
+ int baud = 9600;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ /*
+ * Check whether an invalid uart number has been specified, and
+ * if so, search for the first available port that does have
+ * console support.
+ */
+ if (co->index >= UART_NR)
+ co->index = 0;
+ up = &serial_txx9_ports[co->index];
+ port = &up->port;
+ if (!port->ops)
+ return -ENODEV;
+
+ /*
+ * Temporary fix.
+ */
+ spin_lock_init(&port->lock);
+
+ /*
+ * Disable UART interrupts, set DTR and RTS high
+ * and set speed.
+ */
+ sio_out(up, TXX9_SIDICR, 0);
+ /* initial settings */
+ sio_out(up, TXX9_SILCR,
+ TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
+ ((port->flags & UPF_TXX9_USE_SCLK) ?
+ TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
+ sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver serial_txx9_reg;
+static struct console serial_txx9_console = {
+ .name = TXX9_TTY_NAME,
+ .write = serial_txx9_console_write,
+ .device = uart_console_device,
+ .setup = serial_txx9_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &serial_txx9_reg,
+};
+
+static int __init serial_txx9_console_init(void)
+{
+ register_console(&serial_txx9_console);
+ return 0;
+}
+console_initcall(serial_txx9_console_init);
+
+static int __init serial_txx9_late_console_init(void)
+{
+ if (!(serial_txx9_console.flags & CON_ENABLED))
+ register_console(&serial_txx9_console);
+ return 0;
+}
+late_initcall(serial_txx9_late_console_init);
+
+#define SERIAL_TXX9_CONSOLE &serial_txx9_console
+#else
+#define SERIAL_TXX9_CONSOLE NULL
+#endif
+
+static struct uart_driver serial_txx9_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = "serial_txx9",
+ .devfs_name = TXX9_TTY_DEVFS_NAME,
+ .dev_name = TXX9_TTY_NAME,
+ .major = TXX9_TTY_MAJOR,
+ .minor = TXX9_TTY_MINOR_START,
+ .nr = UART_NR,
+ .cons = SERIAL_TXX9_CONSOLE,
+};
+
+int __init early_serial_txx9_setup(struct uart_port *port)
+{
+ if (port->line >= ARRAY_SIZE(serial_txx9_ports))
+ return -ENODEV;
+
+ serial_txx9_ports[port->line].port = *port;
+ serial_txx9_ports[port->line].port.ops = &serial_txx9_pops;
+ serial_txx9_ports[port->line].port.flags |= UPF_BOOT_AUTOCONF;
+ return 0;
+}
+
+#ifdef ENABLE_SERIAL_TXX9_PCI
+/**
+ * serial_txx9_suspend_port - suspend one serial port
+ * @line: serial line number
+ * @level: the level of port suspension, as per uart_suspend_port
+ *
+ * Suspend one serial port.
+ */
+static void serial_txx9_suspend_port(int line)
+{
+ uart_suspend_port(&serial_txx9_reg, &serial_txx9_ports[line].port);
+}
+
+/**
+ * serial_txx9_resume_port - resume one serial port
+ * @line: serial line number
+ * @level: the level of port resumption, as per uart_resume_port
+ *
+ * Resume one serial port.
+ */
+static void serial_txx9_resume_port(int line)
+{
+ uart_resume_port(&serial_txx9_reg, &serial_txx9_ports[line].port);
+}
+
+/*
+ * Probe one serial board. Unfortunately, there is no rhyme nor reason
+ * to the arrangement of serial ports on a PCI card.
+ */
+static int __devinit
+pciserial_txx9_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
+{
+ struct uart_port port;
+ int line;
+ int rc;
+
+ rc = pci_enable_device(dev);
+ if (rc)
+ return rc;
+
+ memset(&port, 0, sizeof(port));
+ port.ops = &serial_txx9_pops;
+ port.flags |= UPF_BOOT_AUTOCONF; /* uart_ops.config_port will be called */
+ port.flags |= UPF_TXX9_HAVE_CTS_LINE;
+ port.uartclk = 66670000;
+ port.irq = dev->irq;
+ port.iotype = UPIO_PORT;
+ port.iobase = pci_resource_start(dev, 1);
+ line = uart_register_port(&serial_txx9_reg, &port);
+ if (line < 0) {
+ printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), line);
+ }
+ pci_set_drvdata(dev, (void *)(long)line);
+
+ return 0;
+}
+
+static void __devexit pciserial_txx9_remove_one(struct pci_dev *dev)
+{
+ int line = (int)(long)pci_get_drvdata(dev);
+
+ pci_set_drvdata(dev, NULL);
+
+ if (line) {
+ uart_unregister_port(&serial_txx9_reg, line);
+ pci_disable_device(dev);
+ }
+}
+
+static int pciserial_txx9_suspend_one(struct pci_dev *dev, u32 state)
+{
+ int line = (int)(long)pci_get_drvdata(dev);
+
+ if (line)
+ serial_txx9_suspend_port(line);
+ return 0;
+}
+
+static int pciserial_txx9_resume_one(struct pci_dev *dev)
+{
+ int line = (int)(long)pci_get_drvdata(dev);
+
+ if (line)
+ serial_txx9_resume_port(line);
+ return 0;
+}
+
+static struct pci_device_id serial_txx9_pci_tbl[] = {
+ { PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_MISC,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0, 0 },
+ { 0, }
+};
+
+static struct pci_driver serial_txx9_pci_driver = {
+ .name = "serial_txx9",
+ .probe = pciserial_txx9_init_one,
+ .remove = __devexit_p(pciserial_txx9_remove_one),
+ .suspend = pciserial_txx9_suspend_one,
+ .resume = pciserial_txx9_resume_one,
+ .id_table = serial_txx9_pci_tbl,
+};
+
+MODULE_DEVICE_TABLE(pci, serial_txx9_pci_tbl);
+#endif /* ENABLE_SERIAL_TXX9_PCI */
+
+static int __init serial_txx9_init(void)
+{
+ int ret;
+
+ printk(KERN_INFO "%s version %s\n", serial_name, serial_version);
+
+ ret = uart_register_driver(&serial_txx9_reg);
+ if (ret >= 0) {
+ serial_txx9_register_ports(&serial_txx9_reg);
+
+#ifdef ENABLE_SERIAL_TXX9_PCI
+ ret = pci_module_init(&serial_txx9_pci_driver);
+#endif
+ }
+ return ret;
+}
+
+static void __exit serial_txx9_exit(void)
+{
+ int i;
+
+#ifdef ENABLE_SERIAL_TXX9_PCI
+ pci_unregister_driver(&serial_txx9_pci_driver);
+#endif
+ for (i = 0; i < UART_NR; i++)
+ uart_remove_one_port(&serial_txx9_reg, &serial_txx9_ports[i].port);
+
+ uart_unregister_driver(&serial_txx9_reg);
+}
+
+module_init(serial_txx9_init);
+module_exit(serial_txx9_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("TX39/49 serial driver");
+
+MODULE_ALIAS_CHARDEV_MAJOR(TXX9_TTY_MAJOR);