Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/usb/serial/keyspan_usa26msg.h b/drivers/usb/serial/keyspan_usa26msg.h
new file mode 100644
index 0000000..3808727
--- /dev/null
+++ b/drivers/usb/serial/keyspan_usa26msg.h
@@ -0,0 +1,260 @@
+/*
+ usa26msg.h
+
+ Copyright (C) 1998-2000 InnoSys Incorporated. All Rights Reserved
+ This file is available under a BSD-style copyright
+
+ Keyspan USB Async Message Formats for the USA28X
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions are
+ met:
+
+ 1. Redistributions of source code must retain this licence text
+ without modification, this list of conditions, and the following
+ disclaimer. The following copyright notice must appear immediately at
+ the beginning of all source files:
+
+ Copyright (C) 1998-2000 InnoSys Incorporated. All Rights Reserved
+
+ This file is available under a BSD-style copyright
+
+ 2. The name of InnoSys Incorporated may not be used to endorse or promote
+ products derived from this software without specific prior written
+ permission.
+
+ THIS SOFTWARE IS PROVIDED BY INNOSYS CORP. ``AS IS'' AND ANY EXPRESS OR
+ IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
+ OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
+ INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
+ OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
+ SUCH DAMAGE.
+
+ Third revision: USA28X version (aka USA26)
+
+ Buffer formats for RX/TX data messages are not defined by
+ a structure, but are described here:
+
+ USB OUT (host -> USAxx, transmit) messages contain a
+ REQUEST_ACK indicator (set to 0xff to request an ACK at the
+ completion of transmit; 0x00 otherwise), followed by data:
+
+ RQSTACK DAT DAT DAT ...
+
+ with a total data length of 63.
+
+ USB IN (USAxx -> host, receive) messages begin with a status
+ byte in which the 0x80 bit is either:
+
+ (a) 0x80 bit clear
+ indicates that the bytes following it are all data
+ bytes:
+
+ STAT DATA DATA DATA DATA DATA ...
+
+ for a total of up to 63 DATA bytes,
+
+ or:
+
+ (b) 0x80 bit set
+ indiates that the bytes following alternate data and
+ status bytes:
+
+ STAT DATA STAT DATA STAT DATA STAT DATA ...
+
+ for a total of up to 32 DATA bytes.
+
+ The valid bits in the STAT bytes are:
+
+ OVERRUN 0x02
+ PARITY 0x04
+ FRAMING 0x08
+ BREAK 0x10
+
+ Notes:
+
+ (1) The OVERRUN bit can appear in either (a) or (b) format
+ messages, but the but the PARITY/FRAMING/BREAK bits
+ only appear in (b) format messages.
+ (2) For the host to determine the exact point at which the
+ overrun occurred (to identify the point in the data
+ stream at which the data was lost), it needs to count
+ 128 characters, starting at the first character of the
+ message in which OVERRUN was reported; the lost character(s)
+ would have been received between the 128th and 129th
+ characters.
+ (3) An RX data message in which the first byte has 0x80 clear
+ serves as a "break off" indicator.
+
+ revision history:
+
+ 1999feb10 add reportHskiaChanges to allow us to ignore them
+ 1999feb10 add txAckThreshold for fast+loose throughput enhancement
+ 1999mar30 beef up support for RX error reporting
+ 1999apr14 add resetDataToggle to control message
+ 2000jan04 merge with usa17msg.h
+ 2000jun01 add extended BSD-style copyright text
+ 2001jul05 change message format to improve OVERRUN case
+
+ Note on shared names:
+
+ In the case of fields which have been merged between the USA17
+ and USA26 definitions, the USA26 definition is the first part
+ of the name and the USA17 definition is the second part of the
+ name; both meanings are described below.
+*/
+
+#ifndef __USA26MSG__
+#define __USA26MSG__
+
+
+struct keyspan_usa26_portControlMessage
+{
+ /*
+ there are three types of "commands" sent in the control message:
+
+ 1. configuration changes which must be requested by setting
+ the corresponding "set" flag (and should only be requested
+ when necessary, to reduce overhead on the USA26):
+ */
+ u8 setClocking, // BOTH: host requests baud rate be set
+ baudLo, // BOTH: host does baud divisor calculation
+ baudHi, // BOTH: baudHi is only used for first port (gives lower rates)
+ externalClock_txClocking,
+ // USA26: 0=internal, other=external
+ // USA17: 0=internal, other=external/RI
+ rxClocking, // USA17: 0=internal, 1=external/RI, other=external/DSR
+
+
+ setLcr, // BOTH: host requests lcr be set
+ lcr, // BOTH: use PARITY, STOPBITS, DATABITS below
+
+ setFlowControl, // BOTH: host requests flow control be set
+ ctsFlowControl, // BOTH: 1=use CTS flow control, 0=don't
+ xonFlowControl, // BOTH: 1=use XON/XOFF flow control, 0=don't
+ xonChar, // BOTH: specified in current character format
+ xoffChar, // BOTH: specified in current character format
+
+ setTxTriState_setRts,
+ // USA26: host requests TX tri-state be set
+ // USA17: host requests RTS output be set
+ txTriState_rts, // BOTH: 1=active (normal), 0=tristate (off)
+
+ setHskoa_setDtr,
+ // USA26: host requests HSKOA output be set
+ // USA17: host requests DTR output be set
+ hskoa_dtr, // BOTH: 1=on, 0=off
+
+ setPrescaler, // USA26: host requests prescalar be set (default: 13)
+ prescaler; // BOTH: specified as N/8; values 8-ff are valid
+ // must be set any time internal baud rate is set;
+ // must not be set when external clocking is used
+ // note: in USA17, prescaler is applied whenever
+ // setClocking is requested
+
+ /*
+ 3. configuration data which is simply used as is (no overhead,
+ but must be specified correctly in every host message).
+ */
+ u8 forwardingLength, // BOTH: forward when this number of chars available
+ reportHskiaChanges_dsrFlowControl,
+ // USA26: 1=normal; 0=ignore external clock
+ // USA17: 1=use DSR flow control, 0=don't
+ txAckThreshold, // BOTH: 0=not allowed, 1=normal, 2-255 deliver ACK faster
+ loopbackMode; // BOTH: 0=no loopback, 1=loopback enabled
+
+ /*
+ 4. commands which are flags only; these are processed in order
+ (so that, e.g., if both _txOn and _txOff flags are set, the
+ port ends in a TX_OFF state); any non-zero value is respected
+ */
+ u8 _txOn, // BOTH: enable transmitting (and continue if there's data)
+ _txOff, // BOTH: stop transmitting
+ txFlush, // BOTH: toss outbound data
+ txBreak, // BOTH: turn on break (cleared by _txOn)
+ rxOn, // BOTH: turn on receiver
+ rxOff, // BOTH: turn off receiver
+ rxFlush, // BOTH: toss inbound data
+ rxForward, // BOTH: forward all inbound data, NOW (as if fwdLen==1)
+ returnStatus, // BOTH: return current status (even if it hasn't changed)
+ resetDataToggle;// BOTH: reset data toggle state to DATA0
+
+};
+
+// defines for bits in lcr
+#define USA_DATABITS_5 0x00
+#define USA_DATABITS_6 0x01
+#define USA_DATABITS_7 0x02
+#define USA_DATABITS_8 0x03
+#define STOPBITS_5678_1 0x00 // 1 stop bit for all byte sizes
+#define STOPBITS_5_1p5 0x04 // 1.5 stop bits for 5-bit byte
+#define STOPBITS_678_2 0x04 // 2 stop bits for 6/7/8-bit byte
+#define USA_PARITY_NONE 0x00
+#define USA_PARITY_ODD 0x08
+#define USA_PARITY_EVEN 0x18
+#define PARITY_1 0x28
+#define PARITY_0 0x38
+
+// all things called "StatusMessage" are sent on the status endpoint
+
+struct keyspan_usa26_portStatusMessage // one for each port
+{
+ u8 port, // BOTH: 0=first, 1=second, other=see below
+ hskia_cts, // USA26: reports HSKIA pin
+ // USA17: reports CTS pin
+ gpia_dcd, // USA26: reports GPIA pin
+ // USA17: reports DCD pin
+ dsr, // USA17: reports DSR pin
+ ri, // USA17: reports RI pin
+ _txOff, // port has been disabled (by host)
+ _txXoff, // port is in XOFF state (either host or RX XOFF)
+ rxEnabled, // as configured by rxOn/rxOff 1=on, 0=off
+ controlResponse;// 1=a control message has been processed
+};
+
+// bits in RX data message when STAT byte is included
+#define RXERROR_OVERRUN 0x02
+#define RXERROR_PARITY 0x04
+#define RXERROR_FRAMING 0x08
+#define RXERROR_BREAK 0x10
+
+struct keyspan_usa26_globalControlMessage
+{
+ u8 sendGlobalStatus, // 2=request for two status responses
+ resetStatusToggle, // 1=reset global status toggle
+ resetStatusCount; // a cycling value
+};
+
+struct keyspan_usa26_globalStatusMessage
+{
+ u8 port, // 3
+ sendGlobalStatus, // from request, decremented
+ resetStatusCount; // as in request
+};
+
+struct keyspan_usa26_globalDebugMessage
+{
+ u8 port, // 2
+ a,
+ b,
+ c,
+ d;
+};
+
+// ie: the maximum length of an EZUSB endpoint buffer
+#define MAX_DATA_LEN 64
+
+// update status approx. 60 times a second (16.6666 ms)
+#define STATUS_UPDATE_INTERVAL 16
+
+// status rationing tuning value (each port gets checked each n ms)
+#define STATUS_RATION 10
+
+#endif
+
+