Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/include/asm-cris/etraxgpio.h b/include/asm-cris/etraxgpio.h
new file mode 100644
index 0000000..cf04af9
--- /dev/null
+++ b/include/asm-cris/etraxgpio.h
@@ -0,0 +1,104 @@
+/* $Id: etraxgpio.h,v 1.8 2002/06/17 15:53:07 johana Exp $ */
+/*
+ * The following devices are accessable using this driver using
+ * GPIO_MAJOR (120) and a couple of minor numbers:
+ * For ETRAX 100LX (ARCH_V10):
+ * /dev/gpioa minor 0, 8 bit GPIO, each bit can change direction
+ * /dev/gpiob minor 1, 8 bit GPIO, each bit can change direction
+ * /dev/leds minor 2, Access to leds depending on kernelconfig
+ * /dev/gpiog minor 3
+ g0dir, g8_15dir, g16_23dir, g24 dir configurable in R_GEN_CONFIG
+ g1-g7 and g25-g31 is both input and outputs but on different pins
+ Also note that some bits change pins depending on what interfaces
+ are enabled.
+ *
+ *
+ * For ETRAX 200 (ARCH_V32):
+ * /dev/gpioa minor 0, 8 bit GPIO, each bit can change direction
+ * /dev/gpiob minor 1, 18 bit GPIO, each bit can change direction
+ * /dev/gpioc minor 2, 18 bit GPIO, each bit can change direction
+ * /dev/gpiod minor 3, 18 bit GPIO, each bit can change direction
+ * /dev/gpioe minor 4, 18 bit GPIO, each bit can change direction
+ * /dev/leds minor 5, Access to leds depending on kernelconfig
+ *
+ */
+#ifndef _ASM_ETRAXGPIO_H
+#define _ASM_ETRAXGPIO_H
+
+#include <linux/config.h>
+/* etraxgpio _IOC_TYPE, bits 8 to 15 in ioctl cmd */
+#ifdef CONFIG_ETRAX_ARCH_V10
+#define ETRAXGPIO_IOCTYPE 43
+#define GPIO_MINOR_A 0
+#define GPIO_MINOR_B 1
+#define GPIO_MINOR_LEDS 2
+#define GPIO_MINOR_G 3
+#define GPIO_MINOR_LAST 3
+#endif
+#ifdef CONFIG_ETRAX_ARCH_V32
+#define ETRAXGPIO_IOCTYPE 43
+#define GPIO_MINOR_A 0
+#define GPIO_MINOR_B 1
+#define GPIO_MINOR_C 2
+#define GPIO_MINOR_D 3
+#define GPIO_MINOR_E 4
+#define GPIO_MINOR_LEDS 5
+#define GPIO_MINOR_LAST 5
+#endif
+
+/* supported ioctl _IOC_NR's */
+
+#define IO_READBITS 0x1 /* read and return current port bits (obsolete) */
+#define IO_SETBITS 0x2 /* set the bits marked by 1 in the argument */
+#define IO_CLRBITS 0x3 /* clear the bits marked by 1 in the argument */
+
+/* the alarm is waited for by select() */
+
+#define IO_HIGHALARM 0x4 /* set alarm on high for bits marked by 1 */
+#define IO_LOWALARM 0x5 /* set alarm on low for bits marked by 1 */
+#define IO_CLRALARM 0x6 /* clear alarm for bits marked by 1 */
+
+/* LED ioctl */
+#define IO_LEDACTIVE_SET 0x7 /* set active led
+ * 0=off, 1=green, 2=red, 3=yellow */
+
+/* GPIO direction ioctl's */
+#define IO_READDIR 0x8 /* Read direction 0=input 1=output (obsolete) */
+#define IO_SETINPUT 0x9 /* Set direction for bits set, 0=unchanged 1=input,
+ returns mask with current inputs (obsolete) */
+#define IO_SETOUTPUT 0xA /* Set direction for bits set, 0=unchanged 1=output,
+ returns mask with current outputs (obsolete)*/
+
+/* LED ioctl extended */
+#define IO_LED_SETBIT 0xB
+#define IO_LED_CLRBIT 0xC
+
+/* SHUTDOWN ioctl */
+#define IO_SHUTDOWN 0xD
+#define IO_GET_PWR_BT 0xE
+
+/* Bit toggling in driver settings */
+/* bit set in low byte0 is CLK mask (0x00FF),
+ bit set in byte1 is DATA mask (0xFF00)
+ msb, data_mask[7:0] , clk_mask[7:0]
+ */
+#define IO_CFG_WRITE_MODE 0xF
+#define IO_CFG_WRITE_MODE_VALUE(msb, data_mask, clk_mask) \
+ ( (((msb)&1) << 16) | (((data_mask) &0xFF) << 8) | ((clk_mask) & 0xFF) )
+
+/* The following 4 ioctl's take a pointer as argument and handles
+ * 32 bit ports (port G) properly.
+ * These replaces IO_READBITS,IO_SETINPUT AND IO_SETOUTPUT
+ */
+#define IO_READ_INBITS 0x10 /* *arg is result of reading the input pins */
+#define IO_READ_OUTBITS 0x11 /* *arg is result of reading the output shadow */
+#define IO_SETGET_INPUT 0x12 /* bits set in *arg is set to input,
+ * *arg updated with current input pins.
+ */
+#define IO_SETGET_OUTPUT 0x13 /* bits set in *arg is set to output,
+ * *arg updated with current output pins.
+ */
+
+
+
+#endif