Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/include/asm-m68knommu/MC68EZ328.h b/include/asm-m68knommu/MC68EZ328.h
new file mode 100644
index 0000000..801933d
--- /dev/null
+++ b/include/asm-m68knommu/MC68EZ328.h
@@ -0,0 +1,1253 @@
+
+/* include/asm-m68knommu/MC68EZ328.h: 'EZ328 control registers
+ *
+ * Copyright (C) 1999 Vladimir Gurevich <vgurevic@cisco.com>
+ * Bear & Hare Software, Inc.
+ *
+ * Based on include/asm-m68knommu/MC68332.h
+ * Copyright (C) 1998 Kenneth Albanowski <kjahds@kjahds.com>,
+ * The Silver Hammer Group, Ltd.
+ *
+ */
+
+#ifndef _MC68EZ328_H_
+#define _MC68EZ328_H_
+
+#define BYTE_REF(addr) (*((volatile unsigned char*)addr))
+#define WORD_REF(addr) (*((volatile unsigned short*)addr))
+#define LONG_REF(addr) (*((volatile unsigned long*)addr))
+
+#define PUT_FIELD(field, val) (((val) << field##_SHIFT) & field##_MASK)
+#define GET_FIELD(reg, field) (((reg) & field##_MASK) >> field##_SHIFT)
+
+/**********
+ *
+ * 0xFFFFF0xx -- System Control
+ *
+ **********/
+
+/*
+ * System Control Register (SCR)
+ */
+#define SCR_ADDR 0xfffff000
+#define SCR BYTE_REF(SCR_ADDR)
+
+#define SCR_WDTH8 0x01 /* 8-Bit Width Select */
+#define SCR_DMAP 0x04 /* Double Map */
+#define SCR_SO 0x08 /* Supervisor Only */
+#define SCR_BETEN 0x10 /* Bus-Error Time-Out Enable */
+#define SCR_PRV 0x20 /* Privilege Violation */
+#define SCR_WPV 0x40 /* Write Protect Violation */
+#define SCR_BETO 0x80 /* Bus-Error TimeOut */
+
+/*
+ * Silicon ID Register (Mask Revision Register (MRR) for '328 Compatibility)
+ */
+#define MRR_ADDR 0xfffff004
+#define MRR LONG_REF(MRR_ADDR)
+
+/**********
+ *
+ * 0xFFFFF1xx -- Chip-Select logic
+ *
+ **********/
+
+/*
+ * Chip Select Group Base Registers
+ */
+#define CSGBA_ADDR 0xfffff100
+#define CSGBB_ADDR 0xfffff102
+
+#define CSGBC_ADDR 0xfffff104
+#define CSGBD_ADDR 0xfffff106
+
+#define CSGBA WORD_REF(CSGBA_ADDR)
+#define CSGBB WORD_REF(CSGBB_ADDR)
+#define CSGBC WORD_REF(CSGBC_ADDR)
+#define CSGBD WORD_REF(CSGBD_ADDR)
+
+/*
+ * Chip Select Registers
+ */
+#define CSA_ADDR 0xfffff110
+#define CSB_ADDR 0xfffff112
+#define CSC_ADDR 0xfffff114
+#define CSD_ADDR 0xfffff116
+
+#define CSA WORD_REF(CSA_ADDR)
+#define CSB WORD_REF(CSB_ADDR)
+#define CSC WORD_REF(CSC_ADDR)
+#define CSD WORD_REF(CSD_ADDR)
+
+#define CSA_EN 0x0001 /* Chip-Select Enable */
+#define CSA_SIZ_MASK 0x000e /* Chip-Select Size */
+#define CSA_SIZ_SHIFT 1
+#define CSA_WS_MASK 0x0070 /* Wait State */
+#define CSA_WS_SHIFT 4
+#define CSA_BSW 0x0080 /* Data Bus Width */
+#define CSA_FLASH 0x0100 /* FLASH Memory Support */
+#define CSA_RO 0x8000 /* Read-Only */
+
+#define CSB_EN 0x0001 /* Chip-Select Enable */
+#define CSB_SIZ_MASK 0x000e /* Chip-Select Size */
+#define CSB_SIZ_SHIFT 1
+#define CSB_WS_MASK 0x0070 /* Wait State */
+#define CSB_WS_SHIFT 4
+#define CSB_BSW 0x0080 /* Data Bus Width */
+#define CSB_FLASH 0x0100 /* FLASH Memory Support */
+#define CSB_UPSIZ_MASK 0x1800 /* Unprotected memory block size */
+#define CSB_UPSIZ_SHIFT 11
+#define CSB_ROP 0x2000 /* Readonly if protected */
+#define CSB_SOP 0x4000 /* Supervisor only if protected */
+#define CSB_RO 0x8000 /* Read-Only */
+
+#define CSC_EN 0x0001 /* Chip-Select Enable */
+#define CSC_SIZ_MASK 0x000e /* Chip-Select Size */
+#define CSC_SIZ_SHIFT 1
+#define CSC_WS_MASK 0x0070 /* Wait State */
+#define CSC_WS_SHIFT 4
+#define CSC_BSW 0x0080 /* Data Bus Width */
+#define CSC_FLASH 0x0100 /* FLASH Memory Support */
+#define CSC_UPSIZ_MASK 0x1800 /* Unprotected memory block size */
+#define CSC_UPSIZ_SHIFT 11
+#define CSC_ROP 0x2000 /* Readonly if protected */
+#define CSC_SOP 0x4000 /* Supervisor only if protected */
+#define CSC_RO 0x8000 /* Read-Only */
+
+#define CSD_EN 0x0001 /* Chip-Select Enable */
+#define CSD_SIZ_MASK 0x000e /* Chip-Select Size */
+#define CSD_SIZ_SHIFT 1
+#define CSD_WS_MASK 0x0070 /* Wait State */
+#define CSD_WS_SHIFT 4
+#define CSD_BSW 0x0080 /* Data Bus Width */
+#define CSD_FLASH 0x0100 /* FLASH Memory Support */
+#define CSD_DRAM 0x0200 /* Dram Selection */
+#define CSD_COMB 0x0400 /* Combining */
+#define CSD_UPSIZ_MASK 0x1800 /* Unprotected memory block size */
+#define CSD_UPSIZ_SHIFT 11
+#define CSD_ROP 0x2000 /* Readonly if protected */
+#define CSD_SOP 0x4000 /* Supervisor only if protected */
+#define CSD_RO 0x8000 /* Read-Only */
+
+/*
+ * Emulation Chip-Select Register
+ */
+#define EMUCS_ADDR 0xfffff118
+#define EMUCS WORD_REF(EMUCS_ADDR)
+
+#define EMUCS_WS_MASK 0x0070
+#define EMUCS_WS_SHIFT 4
+
+/**********
+ *
+ * 0xFFFFF2xx -- Phase Locked Loop (PLL) & Power Control
+ *
+ **********/
+
+/*
+ * PLL Control Register
+ */
+#define PLLCR_ADDR 0xfffff200
+#define PLLCR WORD_REF(PLLCR_ADDR)
+
+#define PLLCR_DISPLL 0x0008 /* Disable PLL */
+#define PLLCR_CLKEN 0x0010 /* Clock (CLKO pin) enable */
+#define PLLCR_PRESC 0x0020 /* VCO prescaler */
+#define PLLCR_SYSCLK_SEL_MASK 0x0700 /* System Clock Selection */
+#define PLLCR_SYSCLK_SEL_SHIFT 8
+#define PLLCR_LCDCLK_SEL_MASK 0x3800 /* LCD Clock Selection */
+#define PLLCR_LCDCLK_SEL_SHIFT 11
+
+/* '328-compatible definitions */
+#define PLLCR_PIXCLK_SEL_MASK PLLCR_LCDCLK_SEL_MASK
+#define PLLCR_PIXCLK_SEL_SHIFT PLLCR_LCDCLK_SEL_SHIFT
+
+/*
+ * PLL Frequency Select Register
+ */
+#define PLLFSR_ADDR 0xfffff202
+#define PLLFSR WORD_REF(PLLFSR_ADDR)
+
+#define PLLFSR_PC_MASK 0x00ff /* P Count */
+#define PLLFSR_PC_SHIFT 0
+#define PLLFSR_QC_MASK 0x0f00 /* Q Count */
+#define PLLFSR_QC_SHIFT 8
+#define PLLFSR_PROT 0x4000 /* Protect P & Q */
+#define PLLFSR_CLK32 0x8000 /* Clock 32 (kHz) */
+
+/*
+ * Power Control Register
+ */
+#define PCTRL_ADDR 0xfffff207
+#define PCTRL BYTE_REF(PCTRL_ADDR)
+
+#define PCTRL_WIDTH_MASK 0x1f /* CPU Clock bursts width */
+#define PCTRL_WIDTH_SHIFT 0
+#define PCTRL_PCEN 0x80 /* Power Control Enable */
+
+/**********
+ *
+ * 0xFFFFF3xx -- Interrupt Controller
+ *
+ **********/
+
+/*
+ * Interrupt Vector Register
+ */
+#define IVR_ADDR 0xfffff300
+#define IVR BYTE_REF(IVR_ADDR)
+
+#define IVR_VECTOR_MASK 0xF8
+
+/*
+ * Interrupt control Register
+ */
+#define ICR_ADDR 0xfffff302
+#define ICR WORD_REF(ICR_ADDR)
+
+#define ICR_POL5 0x0080 /* Polarity Control for IRQ5 */
+#define ICR_ET6 0x0100 /* Edge Trigger Select for IRQ6 */
+#define ICR_ET3 0x0200 /* Edge Trigger Select for IRQ3 */
+#define ICR_ET2 0x0400 /* Edge Trigger Select for IRQ2 */
+#define ICR_ET1 0x0800 /* Edge Trigger Select for IRQ1 */
+#define ICR_POL6 0x1000 /* Polarity Control for IRQ6 */
+#define ICR_POL3 0x2000 /* Polarity Control for IRQ3 */
+#define ICR_POL2 0x4000 /* Polarity Control for IRQ2 */
+#define ICR_POL1 0x8000 /* Polarity Control for IRQ1 */
+
+/*
+ * Interrupt Mask Register
+ */
+#define IMR_ADDR 0xfffff304
+#define IMR LONG_REF(IMR_ADDR)
+
+/*
+ * Define the names for bit positions first. This is useful for
+ * request_irq
+ */
+#define SPI_IRQ_NUM 0 /* SPI interrupt */
+#define TMR_IRQ_NUM 1 /* Timer interrupt */
+#define UART_IRQ_NUM 2 /* UART interrupt */
+#define WDT_IRQ_NUM 3 /* Watchdog Timer interrupt */
+#define RTC_IRQ_NUM 4 /* RTC interrupt */
+#define KB_IRQ_NUM 6 /* Keyboard Interrupt */
+#define PWM_IRQ_NUM 7 /* Pulse-Width Modulator int. */
+#define INT0_IRQ_NUM 8 /* External INT0 */
+#define INT1_IRQ_NUM 9 /* External INT1 */
+#define INT2_IRQ_NUM 10 /* External INT2 */
+#define INT3_IRQ_NUM 11 /* External INT3 */
+#define IRQ1_IRQ_NUM 16 /* IRQ1 */
+#define IRQ2_IRQ_NUM 17 /* IRQ2 */
+#define IRQ3_IRQ_NUM 18 /* IRQ3 */
+#define IRQ6_IRQ_NUM 19 /* IRQ6 */
+#define IRQ5_IRQ_NUM 20 /* IRQ5 */
+#define SAM_IRQ_NUM 22 /* Sampling Timer for RTC */
+#define EMIQ_IRQ_NUM 23 /* Emulator Interrupt */
+
+/* '328-compatible definitions */
+#define SPIM_IRQ_NUM SPI_IRQ_NUM
+#define TMR1_IRQ_NUM TMR_IRQ_NUM
+
+/*
+ * Here go the bitmasks themselves
+ */
+#define IMR_MSPI (1 << SPI_IRQ_NUM) /* Mask SPI interrupt */
+#define IMR_MTMR (1 << TMR_IRQ_NUM) /* Mask Timer interrupt */
+#define IMR_MUART (1 << UART_IRQ_NUM) /* Mask UART interrupt */
+#define IMR_MWDT (1 << WDT_IRQ_NUM) /* Mask Watchdog Timer interrupt */
+#define IMR_MRTC (1 << RTC_IRQ_NUM) /* Mask RTC interrupt */
+#define IMR_MKB (1 << KB_IRQ_NUM) /* Mask Keyboard Interrupt */
+#define IMR_MPWM (1 << PWM_IRQ_NUM) /* Mask Pulse-Width Modulator int. */
+#define IMR_MINT0 (1 << INT0_IRQ_NUM) /* Mask External INT0 */
+#define IMR_MINT1 (1 << INT1_IRQ_NUM) /* Mask External INT1 */
+#define IMR_MINT2 (1 << INT2_IRQ_NUM) /* Mask External INT2 */
+#define IMR_MINT3 (1 << INT3_IRQ_NUM) /* Mask External INT3 */
+#define IMR_MIRQ1 (1 << IRQ1_IRQ_NUM) /* Mask IRQ1 */
+#define IMR_MIRQ2 (1 << IRQ2_IRQ_NUM) /* Mask IRQ2 */
+#define IMR_MIRQ3 (1 << IRQ3_IRQ_NUM) /* Mask IRQ3 */
+#define IMR_MIRQ6 (1 << IRQ6_IRQ_NUM) /* Mask IRQ6 */
+#define IMR_MIRQ5 (1 << IRQ5_IRQ_NUM) /* Mask IRQ5 */
+#define IMR_MSAM (1 << SAM_IRQ_NUM) /* Mask Sampling Timer for RTC */
+#define IMR_MEMIQ (1 << EMIQ_IRQ_NUM) /* Mask Emulator Interrupt */
+
+/* '328-compatible definitions */
+#define IMR_MSPIM IMR_MSPI
+#define IMR_MTMR1 IMR_MTMR
+
+/*
+ * Interrupt Status Register
+ */
+#define ISR_ADDR 0xfffff30c
+#define ISR LONG_REF(ISR_ADDR)
+
+#define ISR_SPI (1 << SPI_IRQ_NUM) /* SPI interrupt */
+#define ISR_TMR (1 << TMR_IRQ_NUM) /* Timer interrupt */
+#define ISR_UART (1 << UART_IRQ_NUM) /* UART interrupt */
+#define ISR_WDT (1 << WDT_IRQ_NUM) /* Watchdog Timer interrupt */
+#define ISR_RTC (1 << RTC_IRQ_NUM) /* RTC interrupt */
+#define ISR_KB (1 << KB_IRQ_NUM) /* Keyboard Interrupt */
+#define ISR_PWM (1 << PWM_IRQ_NUM) /* Pulse-Width Modulator interrupt */
+#define ISR_INT0 (1 << INT0_IRQ_NUM) /* External INT0 */
+#define ISR_INT1 (1 << INT1_IRQ_NUM) /* External INT1 */
+#define ISR_INT2 (1 << INT2_IRQ_NUM) /* External INT2 */
+#define ISR_INT3 (1 << INT3_IRQ_NUM) /* External INT3 */
+#define ISR_IRQ1 (1 << IRQ1_IRQ_NUM) /* IRQ1 */
+#define ISR_IRQ2 (1 << IRQ2_IRQ_NUM) /* IRQ2 */
+#define ISR_IRQ3 (1 << IRQ3_IRQ_NUM) /* IRQ3 */
+#define ISR_IRQ6 (1 << IRQ6_IRQ_NUM) /* IRQ6 */
+#define ISR_IRQ5 (1 << IRQ5_IRQ_NUM) /* IRQ5 */
+#define ISR_SAM (1 << SAM_IRQ_NUM) /* Sampling Timer for RTC */
+#define ISR_EMIQ (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */
+
+/* '328-compatible definitions */
+#define ISR_SPIM ISR_SPI
+#define ISR_TMR1 ISR_TMR
+
+/*
+ * Interrupt Pending Register
+ */
+#define IPR_ADDR 0xfffff30c
+#define IPR LONG_REF(IPR_ADDR)
+
+#define IPR_SPI (1 << SPI_IRQ_NUM) /* SPI interrupt */
+#define IPR_TMR (1 << TMR_IRQ_NUM) /* Timer interrupt */
+#define IPR_UART (1 << UART_IRQ_NUM) /* UART interrupt */
+#define IPR_WDT (1 << WDT_IRQ_NUM) /* Watchdog Timer interrupt */
+#define IPR_RTC (1 << RTC_IRQ_NUM) /* RTC interrupt */
+#define IPR_KB (1 << KB_IRQ_NUM) /* Keyboard Interrupt */
+#define IPR_PWM (1 << PWM_IRQ_NUM) /* Pulse-Width Modulator interrupt */
+#define IPR_INT0 (1 << INT0_IRQ_NUM) /* External INT0 */
+#define IPR_INT1 (1 << INT1_IRQ_NUM) /* External INT1 */
+#define IPR_INT2 (1 << INT2_IRQ_NUM) /* External INT2 */
+#define IPR_INT3 (1 << INT3_IRQ_NUM) /* External INT3 */
+#define IPR_IRQ1 (1 << IRQ1_IRQ_NUM) /* IRQ1 */
+#define IPR_IRQ2 (1 << IRQ2_IRQ_NUM) /* IRQ2 */
+#define IPR_IRQ3 (1 << IRQ3_IRQ_NUM) /* IRQ3 */
+#define IPR_IRQ6 (1 << IRQ6_IRQ_NUM) /* IRQ6 */
+#define IPR_IRQ5 (1 << IRQ5_IRQ_NUM) /* IRQ5 */
+#define IPR_SAM (1 << SAM_IRQ_NUM) /* Sampling Timer for RTC */
+#define IPR_EMIQ (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */
+
+/* '328-compatible definitions */
+#define IPR_SPIM IPR_SPI
+#define IPR_TMR1 IPR_TMR
+
+/**********
+ *
+ * 0xFFFFF4xx -- Parallel Ports
+ *
+ **********/
+
+/*
+ * Port A
+ */
+#define PADIR_ADDR 0xfffff400 /* Port A direction reg */
+#define PADATA_ADDR 0xfffff401 /* Port A data register */
+#define PAPUEN_ADDR 0xfffff402 /* Port A Pull-Up enable reg */
+
+#define PADIR BYTE_REF(PADIR_ADDR)
+#define PADATA BYTE_REF(PADATA_ADDR)
+#define PAPUEN BYTE_REF(PAPUEN_ADDR)
+
+#define PA(x) (1 << (x))
+
+/*
+ * Port B
+ */
+#define PBDIR_ADDR 0xfffff408 /* Port B direction reg */
+#define PBDATA_ADDR 0xfffff409 /* Port B data register */
+#define PBPUEN_ADDR 0xfffff40a /* Port B Pull-Up enable reg */
+#define PBSEL_ADDR 0xfffff40b /* Port B Select Register */
+
+#define PBDIR BYTE_REF(PBDIR_ADDR)
+#define PBDATA BYTE_REF(PBDATA_ADDR)
+#define PBPUEN BYTE_REF(PBPUEN_ADDR)
+#define PBSEL BYTE_REF(PBSEL_ADDR)
+
+#define PB(x) (1 << (x))
+
+#define PB_CSB0 0x01 /* Use CSB0 as PB[0] */
+#define PB_CSB1 0x02 /* Use CSB1 as PB[1] */
+#define PB_CSC0_RAS0 0x04 /* Use CSC0/RAS0 as PB[2] */
+#define PB_CSC1_RAS1 0x08 /* Use CSC1/RAS1 as PB[3] */
+#define PB_CSD0_CAS0 0x10 /* Use CSD0/CAS0 as PB[4] */
+#define PB_CSD1_CAS1 0x20 /* Use CSD1/CAS1 as PB[5] */
+#define PB_TIN_TOUT 0x40 /* Use TIN/TOUT as PB[6] */
+#define PB_PWMO 0x80 /* Use PWMO as PB[7] */
+
+/*
+ * Port C
+ */
+#define PCDIR_ADDR 0xfffff410 /* Port C direction reg */
+#define PCDATA_ADDR 0xfffff411 /* Port C data register */
+#define PCPDEN_ADDR 0xfffff412 /* Port C Pull-Down enb. reg */
+#define PCSEL_ADDR 0xfffff413 /* Port C Select Register */
+
+#define PCDIR BYTE_REF(PCDIR_ADDR)
+#define PCDATA BYTE_REF(PCDATA_ADDR)
+#define PCPDEN BYTE_REF(PCPDEN_ADDR)
+#define PCSEL BYTE_REF(PCSEL_ADDR)
+
+#define PC(x) (1 << (x))
+
+#define PC_LD0 0x01 /* Use LD0 as PC[0] */
+#define PC_LD1 0x02 /* Use LD1 as PC[1] */
+#define PC_LD2 0x04 /* Use LD2 as PC[2] */
+#define PC_LD3 0x08 /* Use LD3 as PC[3] */
+#define PC_LFLM 0x10 /* Use LFLM as PC[4] */
+#define PC_LLP 0x20 /* Use LLP as PC[5] */
+#define PC_LCLK 0x40 /* Use LCLK as PC[6] */
+#define PC_LACD 0x80 /* Use LACD as PC[7] */
+
+/*
+ * Port D
+ */
+#define PDDIR_ADDR 0xfffff418 /* Port D direction reg */
+#define PDDATA_ADDR 0xfffff419 /* Port D data register */
+#define PDPUEN_ADDR 0xfffff41a /* Port D Pull-Up enable reg */
+#define PDSEL_ADDR 0xfffff41b /* Port D Select Register */
+#define PDPOL_ADDR 0xfffff41c /* Port D Polarity Register */
+#define PDIRQEN_ADDR 0xfffff41d /* Port D IRQ enable register */
+#define PDKBEN_ADDR 0xfffff41e /* Port D Keyboard Enable reg */
+#define PDIQEG_ADDR 0xfffff41f /* Port D IRQ Edge Register */
+
+#define PDDIR BYTE_REF(PDDIR_ADDR)
+#define PDDATA BYTE_REF(PDDATA_ADDR)
+#define PDPUEN BYTE_REF(PDPUEN_ADDR)
+#define PDSEL BYTE_REF(PDSEL_ADDR)
+#define PDPOL BYTE_REF(PDPOL_ADDR)
+#define PDIRQEN BYTE_REF(PDIRQEN_ADDR)
+#define PDKBEN BYTE_REF(PDKBEN_ADDR)
+#define PDIQEG BYTE_REF(PDIQEG_ADDR)
+
+#define PD(x) (1 << (x))
+
+#define PD_INT0 0x01 /* Use INT0 as PD[0] */
+#define PD_INT1 0x02 /* Use INT1 as PD[1] */
+#define PD_INT2 0x04 /* Use INT2 as PD[2] */
+#define PD_INT3 0x08 /* Use INT3 as PD[3] */
+#define PD_IRQ1 0x10 /* Use IRQ1 as PD[4] */
+#define PD_IRQ2 0x20 /* Use IRQ2 as PD[5] */
+#define PD_IRQ3 0x40 /* Use IRQ3 as PD[6] */
+#define PD_IRQ6 0x80 /* Use IRQ6 as PD[7] */
+
+/*
+ * Port E
+ */
+#define PEDIR_ADDR 0xfffff420 /* Port E direction reg */
+#define PEDATA_ADDR 0xfffff421 /* Port E data register */
+#define PEPUEN_ADDR 0xfffff422 /* Port E Pull-Up enable reg */
+#define PESEL_ADDR 0xfffff423 /* Port E Select Register */
+
+#define PEDIR BYTE_REF(PEDIR_ADDR)
+#define PEDATA BYTE_REF(PEDATA_ADDR)
+#define PEPUEN BYTE_REF(PEPUEN_ADDR)
+#define PESEL BYTE_REF(PESEL_ADDR)
+
+#define PE(x) (1 << (x))
+
+#define PE_SPMTXD 0x01 /* Use SPMTXD as PE[0] */
+#define PE_SPMRXD 0x02 /* Use SPMRXD as PE[1] */
+#define PE_SPMCLK 0x04 /* Use SPMCLK as PE[2] */
+#define PE_DWE 0x08 /* Use DWE as PE[3] */
+#define PE_RXD 0x10 /* Use RXD as PE[4] */
+#define PE_TXD 0x20 /* Use TXD as PE[5] */
+#define PE_RTS 0x40 /* Use RTS as PE[6] */
+#define PE_CTS 0x80 /* Use CTS as PE[7] */
+
+/*
+ * Port F
+ */
+#define PFDIR_ADDR 0xfffff428 /* Port F direction reg */
+#define PFDATA_ADDR 0xfffff429 /* Port F data register */
+#define PFPUEN_ADDR 0xfffff42a /* Port F Pull-Up enable reg */
+#define PFSEL_ADDR 0xfffff42b /* Port F Select Register */
+
+#define PFDIR BYTE_REF(PFDIR_ADDR)
+#define PFDATA BYTE_REF(PFDATA_ADDR)
+#define PFPUEN BYTE_REF(PFPUEN_ADDR)
+#define PFSEL BYTE_REF(PFSEL_ADDR)
+
+#define PF(x) (1 << (x))
+
+#define PF_LCONTRAST 0x01 /* Use LCONTRAST as PF[0] */
+#define PF_IRQ5 0x02 /* Use IRQ5 as PF[1] */
+#define PF_CLKO 0x04 /* Use CLKO as PF[2] */
+#define PF_A20 0x08 /* Use A20 as PF[3] */
+#define PF_A21 0x10 /* Use A21 as PF[4] */
+#define PF_A22 0x20 /* Use A22 as PF[5] */
+#define PF_A23 0x40 /* Use A23 as PF[6] */
+#define PF_CSA1 0x80 /* Use CSA1 as PF[7] */
+
+/*
+ * Port G
+ */
+#define PGDIR_ADDR 0xfffff430 /* Port G direction reg */
+#define PGDATA_ADDR 0xfffff431 /* Port G data register */
+#define PGPUEN_ADDR 0xfffff432 /* Port G Pull-Up enable reg */
+#define PGSEL_ADDR 0xfffff433 /* Port G Select Register */
+
+#define PGDIR BYTE_REF(PGDIR_ADDR)
+#define PGDATA BYTE_REF(PGDATA_ADDR)
+#define PGPUEN BYTE_REF(PGPUEN_ADDR)
+#define PGSEL BYTE_REF(PGSEL_ADDR)
+
+#define PG(x) (1 << (x))
+
+#define PG_BUSW_DTACK 0x01 /* Use BUSW/DTACK as PG[0] */
+#define PG_A0 0x02 /* Use A0 as PG[1] */
+#define PG_EMUIRQ 0x04 /* Use EMUIRQ as PG[2] */
+#define PG_HIZ_P_D 0x08 /* Use HIZ/P/D as PG[3] */
+#define PG_EMUCS 0x10 /* Use EMUCS as PG[4] */
+#define PG_EMUBRK 0x20 /* Use EMUBRK as PG[5] */
+
+/**********
+ *
+ * 0xFFFFF5xx -- Pulse-Width Modulator (PWM)
+ *
+ **********/
+
+/*
+ * PWM Control Register
+ */
+#define PWMC_ADDR 0xfffff500
+#define PWMC WORD_REF(PWMC_ADDR)
+
+#define PWMC_CLKSEL_MASK 0x0003 /* Clock Selection */
+#define PWMC_CLKSEL_SHIFT 0
+#define PWMC_REPEAT_MASK 0x000c /* Sample Repeats */
+#define PWMC_REPEAT_SHIFT 2
+#define PWMC_EN 0x0010 /* Enable PWM */
+#define PMNC_FIFOAV 0x0020 /* FIFO Available */
+#define PWMC_IRQEN 0x0040 /* Interrupt Request Enable */
+#define PWMC_IRQ 0x0080 /* Interrupt Request (FIFO empty) */
+#define PWMC_PRESCALER_MASK 0x7f00 /* Incoming Clock prescaler */
+#define PWMC_PRESCALER_SHIFT 8
+#define PWMC_CLKSRC 0x8000 /* Clock Source Select */
+
+/* '328-compatible definitions */
+#define PWMC_PWMEN PWMC_EN
+
+/*
+ * PWM Sample Register
+ */
+#define PWMS_ADDR 0xfffff502
+#define PWMS WORD_REF(PWMS_ADDR)
+
+/*
+ * PWM Period Register
+ */
+#define PWMP_ADDR 0xfffff504
+#define PWMP BYTE_REF(PWMP_ADDR)
+
+/*
+ * PWM Counter Register
+ */
+#define PWMCNT_ADDR 0xfffff505
+#define PWMCNT BYTE_REF(PWMCNT_ADDR)
+
+/**********
+ *
+ * 0xFFFFF6xx -- General-Purpose Timer
+ *
+ **********/
+
+/*
+ * Timer Control register
+ */
+#define TCTL_ADDR 0xfffff600
+#define TCTL WORD_REF(TCTL_ADDR)
+
+#define TCTL_TEN 0x0001 /* Timer Enable */
+#define TCTL_CLKSOURCE_MASK 0x000e /* Clock Source: */
+#define TCTL_CLKSOURCE_STOP 0x0000 /* Stop count (disabled) */
+#define TCTL_CLKSOURCE_SYSCLK 0x0002 /* SYSCLK to prescaler */
+#define TCTL_CLKSOURCE_SYSCLK_16 0x0004 /* SYSCLK/16 to prescaler */
+#define TCTL_CLKSOURCE_TIN 0x0006 /* TIN to prescaler */
+#define TCTL_CLKSOURCE_32KHZ 0x0008 /* 32kHz clock to prescaler */
+#define TCTL_IRQEN 0x0010 /* IRQ Enable */
+#define TCTL_OM 0x0020 /* Output Mode */
+#define TCTL_CAP_MASK 0x00c0 /* Capture Edge: */
+#define TCTL_CAP_RE 0x0040 /* Capture on rizing edge */
+#define TCTL_CAP_FE 0x0080 /* Capture on falling edge */
+#define TCTL_FRR 0x0010 /* Free-Run Mode */
+
+/* '328-compatible definitions */
+#define TCTL1_ADDR TCTL_ADDR
+#define TCTL1 TCTL
+
+/*
+ * Timer Prescaler Register
+ */
+#define TPRER_ADDR 0xfffff602
+#define TPRER WORD_REF(TPRER_ADDR)
+
+/* '328-compatible definitions */
+#define TPRER1_ADDR TPRER_ADDR
+#define TPRER1 TPRER
+
+/*
+ * Timer Compare Register
+ */
+#define TCMP_ADDR 0xfffff604
+#define TCMP WORD_REF(TCMP_ADDR)
+
+/* '328-compatible definitions */
+#define TCMP1_ADDR TCMP_ADDR
+#define TCMP1 TCMP
+
+/*
+ * Timer Capture register
+ */
+#define TCR_ADDR 0xfffff606
+#define TCR WORD_REF(TCR_ADDR)
+
+/* '328-compatible definitions */
+#define TCR1_ADDR TCR_ADDR
+#define TCR1 TCR
+
+/*
+ * Timer Counter Register
+ */
+#define TCN_ADDR 0xfffff608
+#define TCN WORD_REF(TCN_ADDR)
+
+/* '328-compatible definitions */
+#define TCN1_ADDR TCN_ADDR
+#define TCN1 TCN
+
+/*
+ * Timer Status Register
+ */
+#define TSTAT_ADDR 0xfffff60a
+#define TSTAT WORD_REF(TSTAT_ADDR)
+
+#define TSTAT_COMP 0x0001 /* Compare Event occurred */
+#define TSTAT_CAPT 0x0001 /* Capture Event occurred */
+
+/* '328-compatible definitions */
+#define TSTAT1_ADDR TSTAT_ADDR
+#define TSTAT1 TSTAT
+
+/**********
+ *
+ * 0xFFFFF8xx -- Serial Periferial Interface Master (SPIM)
+ *
+ **********/
+
+/*
+ * SPIM Data Register
+ */
+#define SPIMDATA_ADDR 0xfffff800
+#define SPIMDATA WORD_REF(SPIMDATA_ADDR)
+
+/*
+ * SPIM Control/Status Register
+ */
+#define SPIMCONT_ADDR 0xfffff802
+#define SPIMCONT WORD_REF(SPIMCONT_ADDR)
+
+#define SPIMCONT_BIT_COUNT_MASK 0x000f /* Transfer Length in Bytes */
+#define SPIMCONT_BIT_COUNT_SHIFT 0
+#define SPIMCONT_POL 0x0010 /* SPMCLK Signel Polarity */
+#define SPIMCONT_PHA 0x0020 /* Clock/Data phase relationship */
+#define SPIMCONT_IRQEN 0x0040 /* IRQ Enable */
+#define SPIMCONT_IRQ 0x0080 /* Interrupt Request */
+#define SPIMCONT_XCH 0x0100 /* Exchange */
+#define SPIMCONT_ENABLE 0x0200 /* Enable SPIM */
+#define SPIMCONT_DATA_RATE_MASK 0xe000 /* SPIM Data Rate */
+#define SPIMCONT_DATA_RATE_SHIFT 13
+
+/* '328-compatible definitions */
+#define SPIMCONT_SPIMIRQ SPIMCONT_IRQ
+#define SPIMCONT_SPIMEN SPIMCONT_ENABLE
+
+/**********
+ *
+ * 0xFFFFF9xx -- UART
+ *
+ **********/
+
+/*
+ * UART Status/Control Register
+ */
+#define USTCNT_ADDR 0xfffff900
+#define USTCNT WORD_REF(USTCNT_ADDR)
+
+#define USTCNT_TXAE 0x0001 /* Transmitter Available Interrupt Enable */
+#define USTCNT_TXHE 0x0002 /* Transmitter Half Empty Enable */
+#define USTCNT_TXEE 0x0004 /* Transmitter Empty Interrupt Enable */
+#define USTCNT_RXRE 0x0008 /* Receiver Ready Interrupt Enable */
+#define USTCNT_RXHE 0x0010 /* Receiver Half-Full Interrupt Enable */
+#define USTCNT_RXFE 0x0020 /* Receiver Full Interrupt Enable */
+#define USTCNT_CTSD 0x0040 /* CTS Delta Interrupt Enable */
+#define USTCNT_ODEN 0x0080 /* Old Data Interrupt Enable */
+#define USTCNT_8_7 0x0100 /* Eight or seven-bit transmission */
+#define USTCNT_STOP 0x0200 /* Stop bit transmission */
+#define USTCNT_ODD 0x0400 /* Odd Parity */
+#define USTCNT_PEN 0x0800 /* Parity Enable */
+#define USTCNT_CLKM 0x1000 /* Clock Mode Select */
+#define USTCNT_TXEN 0x2000 /* Transmitter Enable */
+#define USTCNT_RXEN 0x4000 /* Receiver Enable */
+#define USTCNT_UEN 0x8000 /* UART Enable */
+
+/* '328-compatible definitions */
+#define USTCNT_TXAVAILEN USTCNT_TXAE
+#define USTCNT_TXHALFEN USTCNT_TXHE
+#define USTCNT_TXEMPTYEN USTCNT_TXEE
+#define USTCNT_RXREADYEN USTCNT_RXRE
+#define USTCNT_RXHALFEN USTCNT_RXHE
+#define USTCNT_RXFULLEN USTCNT_RXFE
+#define USTCNT_CTSDELTAEN USTCNT_CTSD
+#define USTCNT_ODD_EVEN USTCNT_ODD
+#define USTCNT_PARITYEN USTCNT_PEN
+#define USTCNT_CLKMODE USTCNT_CLKM
+#define USTCNT_UARTEN USTCNT_UEN
+
+/*
+ * UART Baud Control Register
+ */
+#define UBAUD_ADDR 0xfffff902
+#define UBAUD WORD_REF(UBAUD_ADDR)
+
+#define UBAUD_PRESCALER_MASK 0x003f /* Actual divisor is 65 - PRESCALER */
+#define UBAUD_PRESCALER_SHIFT 0
+#define UBAUD_DIVIDE_MASK 0x0700 /* Baud Rate freq. divizor */
+#define UBAUD_DIVIDE_SHIFT 8
+#define UBAUD_BAUD_SRC 0x0800 /* Baud Rate Source */
+#define UBAUD_UCLKDIR 0x2000 /* UCLK Direction */
+
+/*
+ * UART Receiver Register
+ */
+#define URX_ADDR 0xfffff904
+#define URX WORD_REF(URX_ADDR)
+
+#define URX_RXDATA_ADDR 0xfffff905
+#define URX_RXDATA BYTE_REF(URX_RXDATA_ADDR)
+
+#define URX_RXDATA_MASK 0x00ff /* Received data */
+#define URX_RXDATA_SHIFT 0
+#define URX_PARITY_ERROR 0x0100 /* Parity Error */
+#define URX_BREAK 0x0200 /* Break Detected */
+#define URX_FRAME_ERROR 0x0400 /* Framing Error */
+#define URX_OVRUN 0x0800 /* Serial Overrun */
+#define URX_OLD_DATA 0x1000 /* Old data in FIFO */
+#define URX_DATA_READY 0x2000 /* Data Ready (FIFO not empty) */
+#define URX_FIFO_HALF 0x4000 /* FIFO is Half-Full */
+#define URX_FIFO_FULL 0x8000 /* FIFO is Full */
+
+/*
+ * UART Transmitter Register
+ */
+#define UTX_ADDR 0xfffff906
+#define UTX WORD_REF(UTX_ADDR)
+
+#define UTX_TXDATA_ADDR 0xfffff907
+#define UTX_TXDATA BYTE_REF(UTX_TXDATA_ADDR)
+
+#define UTX_TXDATA_MASK 0x00ff /* Data to be transmitted */
+#define UTX_TXDATA_SHIFT 0
+#define UTX_CTS_DELTA 0x0100 /* CTS changed */
+#define UTX_CTS_STAT 0x0200 /* CTS State */
+#define UTX_BUSY 0x0400 /* FIFO is busy, sending a character */
+#define UTX_NOCTS 0x0800 /* Ignore CTS */
+#define UTX_SEND_BREAK 0x1000 /* Send a BREAK */
+#define UTX_TX_AVAIL 0x2000 /* Transmit FIFO has a slot available */
+#define UTX_FIFO_HALF 0x4000 /* Transmit FIFO is half empty */
+#define UTX_FIFO_EMPTY 0x8000 /* Transmit FIFO is empty */
+
+/* '328-compatible definitions */
+#define UTX_CTS_STATUS UTX_CTS_STAT
+#define UTX_IGNORE_CTS UTX_NOCTS
+
+/*
+ * UART Miscellaneous Register
+ */
+#define UMISC_ADDR 0xfffff908
+#define UMISC WORD_REF(UMISC_ADDR)
+
+#define UMISC_TX_POL 0x0004 /* Transmit Polarity */
+#define UMISC_RX_POL 0x0008 /* Receive Polarity */
+#define UMISC_IRDA_LOOP 0x0010 /* IrDA Loopback Enable */
+#define UMISC_IRDA_EN 0x0020 /* Infra-Red Enable */
+#define UMISC_RTS 0x0040 /* Set RTS status */
+#define UMISC_RTSCONT 0x0080 /* Choose RTS control */
+#define UMISC_IR_TEST 0x0400 /* IRDA Test Enable */
+#define UMISC_BAUD_RESET 0x0800 /* Reset Baud Rate Generation Counters */
+#define UMISC_LOOP 0x1000 /* Serial Loopback Enable */
+#define UMISC_FORCE_PERR 0x2000 /* Force Parity Error */
+#define UMISC_CLKSRC 0x4000 /* Clock Source */
+#define UMISC_BAUD_TEST 0x8000 /* Enable Baud Test Mode */
+
+/*
+ * UART Non-integer Prescaler Register
+ */
+#define NIPR_ADDR 0xfffff90a
+#define NIPR WORD_REF(NIPR_ADDR)
+
+#define NIPR_STEP_VALUE_MASK 0x00ff /* NI prescaler step value */
+#define NIPR_STEP_VALUE_SHIFT 0
+#define NIPR_SELECT_MASK 0x0700 /* Tap Selection */
+#define NIPR_SELECT_SHIFT 8
+#define NIPR_PRE_SEL 0x8000 /* Non-integer prescaler select */
+
+
+/* generalization of uart control registers to support multiple ports: */
+typedef volatile struct {
+ volatile unsigned short int ustcnt;
+ volatile unsigned short int ubaud;
+ union {
+ volatile unsigned short int w;
+ struct {
+ volatile unsigned char status;
+ volatile unsigned char rxdata;
+ } b;
+ } urx;
+ union {
+ volatile unsigned short int w;
+ struct {
+ volatile unsigned char status;
+ volatile unsigned char txdata;
+ } b;
+ } utx;
+ volatile unsigned short int umisc;
+ volatile unsigned short int nipr;
+ volatile unsigned short int pad1;
+ volatile unsigned short int pad2;
+} m68328_uart __attribute__((packed));
+
+
+/**********
+ *
+ * 0xFFFFFAxx -- LCD Controller
+ *
+ **********/
+
+/*
+ * LCD Screen Starting Address Register
+ */
+#define LSSA_ADDR 0xfffffa00
+#define LSSA LONG_REF(LSSA_ADDR)
+
+#define LSSA_SSA_MASK 0x1ffffffe /* Bits 0 and 29-31 are reserved */
+
+/*
+ * LCD Virtual Page Width Register
+ */
+#define LVPW_ADDR 0xfffffa05
+#define LVPW BYTE_REF(LVPW_ADDR)
+
+/*
+ * LCD Screen Width Register (not compatible with '328 !!!)
+ */
+#define LXMAX_ADDR 0xfffffa08
+#define LXMAX WORD_REF(LXMAX_ADDR)
+
+#define LXMAX_XM_MASK 0x02f0 /* Bits 0-3 and 10-15 are reserved */
+
+/*
+ * LCD Screen Height Register
+ */
+#define LYMAX_ADDR 0xfffffa0a
+#define LYMAX WORD_REF(LYMAX_ADDR)
+
+#define LYMAX_YM_MASK 0x01ff /* Bits 9-15 are reserved */
+
+/*
+ * LCD Cursor X Position Register
+ */
+#define LCXP_ADDR 0xfffffa18
+#define LCXP WORD_REF(LCXP_ADDR)
+
+#define LCXP_CC_MASK 0xc000 /* Cursor Control */
+#define LCXP_CC_TRAMSPARENT 0x0000
+#define LCXP_CC_BLACK 0x4000
+#define LCXP_CC_REVERSED 0x8000
+#define LCXP_CC_WHITE 0xc000
+#define LCXP_CXP_MASK 0x02ff /* Cursor X position */
+
+/*
+ * LCD Cursor Y Position Register
+ */
+#define LCYP_ADDR 0xfffffa1a
+#define LCYP WORD_REF(LCYP_ADDR)
+
+#define LCYP_CYP_MASK 0x01ff /* Cursor Y Position */
+
+/*
+ * LCD Cursor Width and Heigth Register
+ */
+#define LCWCH_ADDR 0xfffffa1c
+#define LCWCH WORD_REF(LCWCH_ADDR)
+
+#define LCWCH_CH_MASK 0x001f /* Cursor Height */
+#define LCWCH_CH_SHIFT 0
+#define LCWCH_CW_MASK 0x1f00 /* Cursor Width */
+#define LCWCH_CW_SHIFT 8
+
+/*
+ * LCD Blink Control Register
+ */
+#define LBLKC_ADDR 0xfffffa1f
+#define LBLKC BYTE_REF(LBLKC_ADDR)
+
+#define LBLKC_BD_MASK 0x7f /* Blink Divisor */
+#define LBLKC_BD_SHIFT 0
+#define LBLKC_BKEN 0x80 /* Blink Enabled */
+
+/*
+ * LCD Panel Interface Configuration Register
+ */
+#define LPICF_ADDR 0xfffffa20
+#define LPICF BYTE_REF(LPICF_ADDR)
+
+#define LPICF_GS_MASK 0x03 /* Gray-Scale Mode */
+#define LPICF_GS_BW 0x00
+#define LPICF_GS_GRAY_4 0x01
+#define LPICF_GS_GRAY_16 0x02
+#define LPICF_PBSIZ_MASK 0x0c /* Panel Bus Width */
+#define LPICF_PBSIZ_1 0x00
+#define LPICF_PBSIZ_2 0x04
+#define LPICF_PBSIZ_4 0x08
+
+/*
+ * LCD Polarity Configuration Register
+ */
+#define LPOLCF_ADDR 0xfffffa21
+#define LPOLCF BYTE_REF(LPOLCF_ADDR)
+
+#define LPOLCF_PIXPOL 0x01 /* Pixel Polarity */
+#define LPOLCF_LPPOL 0x02 /* Line Pulse Polarity */
+#define LPOLCF_FLMPOL 0x04 /* Frame Marker Polarity */
+#define LPOLCF_LCKPOL 0x08 /* LCD Shift Lock Polarity */
+
+/*
+ * LACD (LCD Alternate Crystal Direction) Rate Control Register
+ */
+#define LACDRC_ADDR 0xfffffa23
+#define LACDRC BYTE_REF(LACDRC_ADDR)
+
+#define LACDRC_ACDSLT 0x80 /* Signal Source Select */
+#define LACDRC_ACD_MASK 0x0f /* Alternate Crystal Direction Control */
+#define LACDRC_ACD_SHIFT 0
+
+/*
+ * LCD Pixel Clock Divider Register
+ */
+#define LPXCD_ADDR 0xfffffa25
+#define LPXCD BYTE_REF(LPXCD_ADDR)
+
+#define LPXCD_PCD_MASK 0x3f /* Pixel Clock Divider */
+#define LPXCD_PCD_SHIFT 0
+
+/*
+ * LCD Clocking Control Register
+ */
+#define LCKCON_ADDR 0xfffffa27
+#define LCKCON BYTE_REF(LCKCON_ADDR)
+
+#define LCKCON_DWS_MASK 0x0f /* Display Wait-State */
+#define LCKCON_DWS_SHIFT 0
+#define LCKCON_DWIDTH 0x40 /* Display Memory Width */
+#define LCKCON_LCDON 0x80 /* Enable LCD Controller */
+
+/* '328-compatible definitions */
+#define LCKCON_DW_MASK LCKCON_DWS_MASK
+#define LCKCON_DW_SHIFT LCKCON_DWS_SHIFT
+
+/*
+ * LCD Refresh Rate Adjustment Register
+ */
+#define LRRA_ADDR 0xfffffa29
+#define LRRA BYTE_REF(LRRA_ADDR)
+
+/*
+ * LCD Panning Offset Register
+ */
+#define LPOSR_ADDR 0xfffffa2d
+#define LPOSR BYTE_REF(LPOSR_ADDR)
+
+#define LPOSR_POS_MASK 0x0f /* Pixel Offset Code */
+#define LPOSR_POS_SHIFT 0
+
+/*
+ * LCD Frame Rate Control Modulation Register
+ */
+#define LFRCM_ADDR 0xfffffa31
+#define LFRCM BYTE_REF(LFRCM_ADDR)
+
+#define LFRCM_YMOD_MASK 0x0f /* Vertical Modulation */
+#define LFRCM_YMOD_SHIFT 0
+#define LFRCM_XMOD_MASK 0xf0 /* Horizontal Modulation */
+#define LFRCM_XMOD_SHIFT 4
+
+/*
+ * LCD Gray Palette Mapping Register
+ */
+#define LGPMR_ADDR 0xfffffa33
+#define LGPMR BYTE_REF(LGPMR_ADDR)
+
+#define LGPMR_G1_MASK 0x0f
+#define LGPMR_G1_SHIFT 0
+#define LGPMR_G2_MASK 0xf0
+#define LGPMR_G2_SHIFT 4
+
+/*
+ * PWM Contrast Control Register
+ */
+#define PWMR_ADDR 0xfffffa36
+#define PWMR WORD_REF(PWMR_ADDR)
+
+#define PWMR_PW_MASK 0x00ff /* Pulse Width */
+#define PWMR_PW_SHIFT 0
+#define PWMR_CCPEN 0x0100 /* Contrast Control Enable */
+#define PWMR_SRC_MASK 0x0600 /* Input Clock Source */
+#define PWMR_SRC_LINE 0x0000 /* Line Pulse */
+#define PWMR_SRC_PIXEL 0x0200 /* Pixel Clock */
+#define PWMR_SRC_LCD 0x4000 /* LCD clock */
+
+/**********
+ *
+ * 0xFFFFFBxx -- Real-Time Clock (RTC)
+ *
+ **********/
+
+/*
+ * RTC Hours Minutes and Seconds Register
+ */
+#define RTCTIME_ADDR 0xfffffb00
+#define RTCTIME LONG_REF(RTCTIME_ADDR)
+
+#define RTCTIME_SECONDS_MASK 0x0000003f /* Seconds */
+#define RTCTIME_SECONDS_SHIFT 0
+#define RTCTIME_MINUTES_MASK 0x003f0000 /* Minutes */
+#define RTCTIME_MINUTES_SHIFT 16
+#define RTCTIME_HOURS_MASK 0x1f000000 /* Hours */
+#define RTCTIME_HOURS_SHIFT 24
+
+/*
+ * RTC Alarm Register
+ */
+#define RTCALRM_ADDR 0xfffffb04
+#define RTCALRM LONG_REF(RTCALRM_ADDR)
+
+#define RTCALRM_SECONDS_MASK 0x0000003f /* Seconds */
+#define RTCALRM_SECONDS_SHIFT 0
+#define RTCALRM_MINUTES_MASK 0x003f0000 /* Minutes */
+#define RTCALRM_MINUTES_SHIFT 16
+#define RTCALRM_HOURS_MASK 0x1f000000 /* Hours */
+#define RTCALRM_HOURS_SHIFT 24
+
+/*
+ * Watchdog Timer Register
+ */
+#define WATCHDOG_ADDR 0xfffffb0a
+#define WATCHDOG WORD_REF(WATCHDOG_ADDR)
+
+#define WATCHDOG_EN 0x0001 /* Watchdog Enabled */
+#define WATCHDOG_ISEL 0x0002 /* Select the watchdog interrupt */
+#define WATCHDOG_INTF 0x0080 /* Watchdog interrupt occcured */
+#define WATCHDOG_CNT_MASK 0x0300 /* Watchdog Counter */
+#define WATCHDOG_CNT_SHIFT 8
+
+/*
+ * RTC Control Register
+ */
+#define RTCCTL_ADDR 0xfffffb0c
+#define RTCCTL WORD_REF(RTCCTL_ADDR)
+
+#define RTCCTL_XTL 0x0020 /* Crystal Selection */
+#define RTCCTL_EN 0x0080 /* RTC Enable */
+
+/* '328-compatible definitions */
+#define RTCCTL_384 RTCCTL_XTL
+#define RTCCTL_ENABLE RTCCTL_EN
+
+/*
+ * RTC Interrupt Status Register
+ */
+#define RTCISR_ADDR 0xfffffb0e
+#define RTCISR WORD_REF(RTCISR_ADDR)
+
+#define RTCISR_SW 0x0001 /* Stopwatch timed out */
+#define RTCISR_MIN 0x0002 /* 1-minute interrupt has occurred */
+#define RTCISR_ALM 0x0004 /* Alarm interrupt has occurred */
+#define RTCISR_DAY 0x0008 /* 24-hour rollover interrupt has occurred */
+#define RTCISR_1HZ 0x0010 /* 1Hz interrupt has occurred */
+#define RTCISR_HR 0x0020 /* 1-hour interrupt has occurred */
+#define RTCISR_SAM0 0x0100 /* 4Hz / 4.6875Hz interrupt has occurred */
+#define RTCISR_SAM1 0x0200 /* 8Hz / 9.3750Hz interrupt has occurred */
+#define RTCISR_SAM2 0x0400 /* 16Hz / 18.7500Hz interrupt has occurred */
+#define RTCISR_SAM3 0x0800 /* 32Hz / 37.5000Hz interrupt has occurred */
+#define RTCISR_SAM4 0x1000 /* 64Hz / 75.0000Hz interrupt has occurred */
+#define RTCISR_SAM5 0x2000 /* 128Hz / 150.0000Hz interrupt has occurred */
+#define RTCISR_SAM6 0x4000 /* 256Hz / 300.0000Hz interrupt has occurred */
+#define RTCISR_SAM7 0x8000 /* 512Hz / 600.0000Hz interrupt has occurred */
+
+/*
+ * RTC Interrupt Enable Register
+ */
+#define RTCIENR_ADDR 0xfffffb10
+#define RTCIENR WORD_REF(RTCIENR_ADDR)
+
+#define RTCIENR_SW 0x0001 /* Stopwatch interrupt enable */
+#define RTCIENR_MIN 0x0002 /* 1-minute interrupt enable */
+#define RTCIENR_ALM 0x0004 /* Alarm interrupt enable */
+#define RTCIENR_DAY 0x0008 /* 24-hour rollover interrupt enable */
+#define RTCIENR_1HZ 0x0010 /* 1Hz interrupt enable */
+#define RTCIENR_HR 0x0020 /* 1-hour interrupt enable */
+#define RTCIENR_SAM0 0x0100 /* 4Hz / 4.6875Hz interrupt enable */
+#define RTCIENR_SAM1 0x0200 /* 8Hz / 9.3750Hz interrupt enable */
+#define RTCIENR_SAM2 0x0400 /* 16Hz / 18.7500Hz interrupt enable */
+#define RTCIENR_SAM3 0x0800 /* 32Hz / 37.5000Hz interrupt enable */
+#define RTCIENR_SAM4 0x1000 /* 64Hz / 75.0000Hz interrupt enable */
+#define RTCIENR_SAM5 0x2000 /* 128Hz / 150.0000Hz interrupt enable */
+#define RTCIENR_SAM6 0x4000 /* 256Hz / 300.0000Hz interrupt enable */
+#define RTCIENR_SAM7 0x8000 /* 512Hz / 600.0000Hz interrupt enable */
+
+/*
+ * Stopwatch Minutes Register
+ */
+#define STPWCH_ADDR 0xfffffb12
+#define STPWCH WORD_REF(STPWCH)
+
+#define STPWCH_CNT_MASK 0x003f /* Stopwatch countdown value */
+#define SPTWCH_CNT_SHIFT 0
+
+/*
+ * RTC Day Count Register
+ */
+#define DAYR_ADDR 0xfffffb1a
+#define DAYR WORD_REF(DAYR_ADDR)
+
+#define DAYR_DAYS_MASK 0x1ff /* Day Setting */
+#define DAYR_DAYS_SHIFT 0
+
+/*
+ * RTC Day Alarm Register
+ */
+#define DAYALARM_ADDR 0xfffffb1c
+#define DAYALARM WORD_REF(DAYALARM_ADDR)
+
+#define DAYALARM_DAYSAL_MASK 0x01ff /* Day Setting of the Alarm */
+#define DAYALARM_DAYSAL_SHIFT 0
+
+/**********
+ *
+ * 0xFFFFFCxx -- DRAM Controller
+ *
+ **********/
+
+/*
+ * DRAM Memory Configuration Register
+ */
+#define DRAMMC_ADDR 0xfffffc00
+#define DRAMMC WORD_REF(DRAMMC_ADDR)
+
+#define DRAMMC_ROW12_MASK 0xc000 /* Row address bit for MD12 */
+#define DRAMMC_ROW12_PA10 0x0000
+#define DRAMMC_ROW12_PA21 0x4000
+#define DRAMMC_ROW12_PA23 0x8000
+#define DRAMMC_ROW0_MASK 0x3000 /* Row address bit for MD0 */
+#define DRAMMC_ROW0_PA11 0x0000
+#define DRAMMC_ROW0_PA22 0x1000
+#define DRAMMC_ROW0_PA23 0x2000
+#define DRAMMC_ROW11 0x0800 /* Row address bit for MD11 PA20/PA22 */
+#define DRAMMC_ROW10 0x0400 /* Row address bit for MD10 PA19/PA21 */
+#define DRAMMC_ROW9 0x0200 /* Row address bit for MD9 PA9/PA19 */
+#define DRAMMC_ROW8 0x0100 /* Row address bit for MD8 PA10/PA20 */
+#define DRAMMC_COL10 0x0080 /* Col address bit for MD10 PA11/PA0 */
+#define DRAMMC_COL9 0x0040 /* Col address bit for MD9 PA10/PA0 */
+#define DRAMMC_COL8 0x0020 /* Col address bit for MD8 PA9/PA0 */
+#define DRAMMC_REF_MASK 0x001f /* Reresh Cycle */
+#define DRAMMC_REF_SHIFT 0
+
+/*
+ * DRAM Control Register
+ */
+#define DRAMC_ADDR 0xfffffc02
+#define DRAMC WORD_REF(DRAMC_ADDR)
+
+#define DRAMC_DWE 0x0001 /* DRAM Write Enable */
+#define DRAMC_RST 0x0002 /* Reset Burst Refresh Enable */
+#define DRAMC_LPR 0x0004 /* Low-Power Refresh Enable */
+#define DRAMC_SLW 0x0008 /* Slow RAM */
+#define DRAMC_LSP 0x0010 /* Light Sleep */
+#define DRAMC_MSW 0x0020 /* Slow Multiplexing */
+#define DRAMC_WS_MASK 0x00c0 /* Wait-states */
+#define DRAMC_WS_SHIFT 6
+#define DRAMC_PGSZ_MASK 0x0300 /* Page Size for fast page mode */
+#define DRAMC_PGSZ_SHIFT 8
+#define DRAMC_PGSZ_256K 0x0000
+#define DRAMC_PGSZ_512K 0x0100
+#define DRAMC_PGSZ_1024K 0x0200
+#define DRAMC_PGSZ_2048K 0x0300
+#define DRAMC_EDO 0x0400 /* EDO DRAM */
+#define DRAMC_CLK 0x0800 /* Refresh Timer Clock source select */
+#define DRAMC_BC_MASK 0x3000 /* Page Access Clock Cycle (FP mode) */
+#define DRAMC_BC_SHIFT 12
+#define DRAMC_RM 0x4000 /* Refresh Mode */
+#define DRAMC_EN 0x8000 /* DRAM Controller enable */
+
+
+/**********
+ *
+ * 0xFFFFFDxx -- In-Circuit Emulation (ICE)
+ *
+ **********/
+
+/*
+ * ICE Module Address Compare Register
+ */
+#define ICEMACR_ADDR 0xfffffd00
+#define ICEMACR LONG_REF(ICEMACR_ADDR)
+
+/*
+ * ICE Module Address Mask Register
+ */
+#define ICEMAMR_ADDR 0xfffffd04
+#define ICEMAMR LONG_REF(ICEMAMR_ADDR)
+
+/*
+ * ICE Module Control Compare Register
+ */
+#define ICEMCCR_ADDR 0xfffffd08
+#define ICEMCCR WORD_REF(ICEMCCR_ADDR)
+
+#define ICEMCCR_PD 0x0001 /* Program/Data Cycle Selection */
+#define ICEMCCR_RW 0x0002 /* Read/Write Cycle Selection */
+
+/*
+ * ICE Module Control Mask Register
+ */
+#define ICEMCMR_ADDR 0xfffffd0a
+#define ICEMCMR WORD_REF(ICEMCMR_ADDR)
+
+#define ICEMCMR_PDM 0x0001 /* Program/Data Cycle Mask */
+#define ICEMCMR_RWM 0x0002 /* Read/Write Cycle Mask */
+
+/*
+ * ICE Module Control Register
+ */
+#define ICEMCR_ADDR 0xfffffd0c
+#define ICEMCR WORD_REF(ICEMCR_ADDR)
+
+#define ICEMCR_CEN 0x0001 /* Compare Enable */
+#define ICEMCR_PBEN 0x0002 /* Program Break Enable */
+#define ICEMCR_SB 0x0004 /* Single Breakpoint */
+#define ICEMCR_HMDIS 0x0008 /* HardMap disable */
+#define ICEMCR_BBIEN 0x0010 /* Bus Break Interrupt Enable */
+
+/*
+ * ICE Module Status Register
+ */
+#define ICEMSR_ADDR 0xfffffd0e
+#define ICEMSR WORD_REF(ICEMSR_ADDR)
+
+#define ICEMSR_EMUEN 0x0001 /* Emulation Enable */
+#define ICEMSR_BRKIRQ 0x0002 /* A-Line Vector Fetch Detected */
+#define ICEMSR_BBIRQ 0x0004 /* Bus Break Interrupt Detected */
+#define ICEMSR_EMIRQ 0x0008 /* EMUIRQ Falling Edge Detected */
+
+#endif /* _MC68EZ328_H_ */