Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
diff --git a/include/asm-sparc64/sunbpp.h b/include/asm-sparc64/sunbpp.h
new file mode 100644
index 0000000..b441cc9
--- /dev/null
+++ b/include/asm-sparc64/sunbpp.h
@@ -0,0 +1,80 @@
+/* $Id: sunbpp.h,v 1.1 1999/08/13 06:21:44 shadow Exp $
+ * include/asm-sparc64/sunbpp.h
+ */
+
+#ifndef _ASM_SPARC64_SUNBPP_H
+#define _ASM_SPARC64_SUNBPP_H
+
+struct bpp_regs {
+  /* DMA registers */
+  __volatile__ __u32 p_csr;		/* DMA Control/Status Register */
+  __volatile__ __u32 p_addr;		/* Address Register */
+  __volatile__ __u32 p_bcnt;		/* Byte Count Register */
+  __volatile__ __u32 p_tst_csr;		/* Test Control/Status (DMA2 only) */
+  /* Parallel Port registers */
+  __volatile__ __u16 p_hcr;		/* Hardware Configuration Register */
+  __volatile__ __u16 p_ocr;		/* Operation Configuration Register */
+  __volatile__ __u8 p_dr;		/* Parallel Data Register */
+  __volatile__ __u8 p_tcr;		/* Transfer Control Register */
+  __volatile__ __u8 p_or;		/* Output Register */
+  __volatile__ __u8 p_ir;		/* Input Register */
+  __volatile__ __u16 p_icr;		/* Interrupt Control Register */
+};
+
+/* P_HCR. Time is in increments of SBus clock. */
+#define P_HCR_TEST      0x8000      /* Allows buried counters to be read */
+#define P_HCR_DSW       0x7f00      /* Data strobe width (in ticks) */
+#define P_HCR_DDS       0x007f      /* Data setup before strobe (in ticks) */
+
+/* P_OCR. */
+#define P_OCR_MEM_CLR   0x8000
+#define P_OCR_DATA_SRC  0x4000      /* )                  */
+#define P_OCR_DS_DSEL   0x2000      /* )  Bidirectional      */
+#define P_OCR_BUSY_DSEL 0x1000      /* )    selects            */
+#define P_OCR_ACK_DSEL  0x0800      /* )                  */
+#define P_OCR_EN_DIAG   0x0400
+#define P_OCR_BUSY_OP   0x0200      /* Busy operation */
+#define P_OCR_ACK_OP    0x0100      /* Ack operation */
+#define P_OCR_SRST      0x0080      /* Reset state machines. Not selfcleaning. */
+#define P_OCR_IDLE      0x0008      /* PP data transfer state machine is idle */
+#define P_OCR_V_ILCK    0x0002      /* Versatec faded. Zebra only. */
+#define P_OCR_EN_VER    0x0001      /* Enable Versatec (0 - enable). Zebra only. */
+
+/* P_TCR */
+#define P_TCR_DIR       0x08
+#define P_TCR_BUSY      0x04
+#define P_TCR_ACK       0x02
+#define P_TCR_DS        0x01        /* Strobe */
+
+/* P_OR */
+#define P_OR_V3         0x20        /* )                 */
+#define P_OR_V2         0x10        /* ) on Zebra only   */
+#define P_OR_V1         0x08        /* )                 */
+#define P_OR_INIT       0x04
+#define P_OR_AFXN       0x02        /* Auto Feed */
+#define P_OR_SLCT_IN    0x01
+
+/* P_IR */
+#define P_IR_PE         0x04
+#define P_IR_SLCT       0x02
+#define P_IR_ERR        0x01
+
+/* P_ICR */
+#define P_DS_IRQ        0x8000      /* RW1  */
+#define P_ACK_IRQ       0x4000      /* RW1  */
+#define P_BUSY_IRQ      0x2000      /* RW1  */
+#define P_PE_IRQ        0x1000      /* RW1  */
+#define P_SLCT_IRQ      0x0800      /* RW1  */
+#define P_ERR_IRQ       0x0400      /* RW1  */
+#define P_DS_IRQ_EN     0x0200      /* RW   Always on rising edge */
+#define P_ACK_IRQ_EN    0x0100      /* RW   Always on rising edge */
+#define P_BUSY_IRP      0x0080      /* RW   1= rising edge */
+#define P_BUSY_IRQ_EN   0x0040      /* RW   */
+#define P_PE_IRP        0x0020      /* RW   1= rising edge */
+#define P_PE_IRQ_EN     0x0010      /* RW   */
+#define P_SLCT_IRP      0x0008      /* RW   1= rising edge */
+#define P_SLCT_IRQ_EN   0x0004      /* RW   */
+#define P_ERR_IRP       0x0002      /* RW1  1= rising edge */
+#define P_ERR_IRQ_EN    0x0001      /* RW   */
+
+#endif /* !(_ASM_SPARC64_SUNBPP_H) */