#ifndef __I386_SGI_PIIX_H
#define __I386_SGI_PIIX_H

/*
 * PIIX4 as used on SGI Visual Workstations
 */

#define	PIIX_PM_START		0x0F80

#define	SIO_GPIO_START		0x0FC0

#define	SIO_PM_START		0x0FC8

#define	PMBASE			PIIX_PM_START
#define	GPIREG0			(PMBASE+0x30)
#define	GPIREG(x)		(GPIREG0+((x)/8))
#define	GPIBIT(x)		(1 << ((x)%8))

#define	PIIX_GPI_BD_ID1		18
#define	PIIX_GPI_BD_ID2		19
#define	PIIX_GPI_BD_ID3		20
#define	PIIX_GPI_BD_ID4		21
#define	PIIX_GPI_BD_REG		GPIREG(PIIX_GPI_BD_ID1)
#define	PIIX_GPI_BD_MASK	(GPIBIT(PIIX_GPI_BD_ID1) | \
				GPIBIT(PIIX_GPI_BD_ID2) | \
				GPIBIT(PIIX_GPI_BD_ID3) | \
				GPIBIT(PIIX_GPI_BD_ID4) )

#define	PIIX_GPI_BD_SHIFT	(PIIX_GPI_BD_ID1 % 8)

#define	SIO_INDEX		0x2e
#define	SIO_DATA		0x2f

#define	SIO_DEV_SEL		0x7
#define	SIO_DEV_ENB		0x30
#define	SIO_DEV_MSB		0x60
#define	SIO_DEV_LSB		0x61

#define	SIO_GP_DEV		0x7

#define	SIO_GP_BASE		SIO_GPIO_START
#define	SIO_GP_MSB		(SIO_GP_BASE>>8)
#define	SIO_GP_LSB		(SIO_GP_BASE&0xff)

#define	SIO_GP_DATA1		(SIO_GP_BASE+0)

#define	SIO_PM_DEV		0x8

#define	SIO_PM_BASE		SIO_PM_START
#define	SIO_PM_MSB		(SIO_PM_BASE>>8)
#define	SIO_PM_LSB		(SIO_PM_BASE&0xff)
#define	SIO_PM_INDEX		(SIO_PM_BASE+0)
#define	SIO_PM_DATA		(SIO_PM_BASE+1)

#define	SIO_PM_FER2		0x1

#define	SIO_PM_GP_EN		0x80


/*
 * This is the dev/reg where generating a config cycle will
 * result in a PCI special cycle.
 */
#define SPECIAL_DEV		0xff
#define SPECIAL_REG		0x00

/*
 * PIIX4 needs to see a special cycle with the following data
 * to be convinced the processor has gone into the stop grant
 * state.  PIIX4 insists on seeing this before it will power
 * down a system.
 */
#define PIIX_SPECIAL_STOP		0x00120002

#define PIIX4_RESET_PORT	0xcf9
#define PIIX4_RESET_VAL		0x6

#define PMSTS_PORT		0xf80	// 2 bytes	PM Status
#define PMEN_PORT		0xf82	// 2 bytes	PM Enable
#define	PMCNTRL_PORT		0xf84	// 2 bytes	PM Control

#define PM_SUSPEND_ENABLE	0x2000	// start sequence to suspend state

/*
 * PMSTS and PMEN I/O bit definitions.
 * (Bits are the same in both registers)
 */
#define PM_STS_RSM		(1<<15)	// Resume Status
#define PM_STS_PWRBTNOR		(1<<11)	// Power Button Override
#define PM_STS_RTC		(1<<10)	// RTC status
#define PM_STS_PWRBTN		(1<<8)	// Power Button Pressed?
#define PM_STS_GBL		(1<<5)	// Global Status
#define PM_STS_BM		(1<<4)	// Bus Master Status
#define PM_STS_TMROF		(1<<0)	// Timer Overflow Status.

/*
 * Stop clock GPI register
 */
#define PIIX_GPIREG0			(0xf80 + 0x30)

/*
 * Stop clock GPI bit in GPIREG0
 */
#define	PIIX_GPI_STPCLK		0x4	// STPCLK signal routed back in

#endif