ARM: dts: msm: Add camera sensor dt file for QRD SDM845
Add camera sensor devices support for image sensor,
actuator, OIS, EEPROM, flash of QRD SDM845.
Change-Id: Id7816d30e9b5e40af1e41bebfb14d1b7519f2758
Signed-off-by: Neng Chen <nengchen@codeaurora.org>
diff --git a/arch/arm64/boot/dts/qcom/sdm845-camera-sensor-qrd.dtsi b/arch/arm64/boot/dts/qcom/sdm845-camera-sensor-qrd.dtsi
new file mode 100644
index 0000000..365b383
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-camera-sensor-qrd.dtsi
@@ -0,0 +1,377 @@
+/*
+ * Copyright (c) 2016-2018, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+&soc {
+ led_flash_rear: qcom,camera-flash@0 {
+ cell-index = <0>;
+ reg = <0x00 0x00>;
+ compatible = "qcom,camera-flash";
+ flash-source = <&pmi8998_flash0 &pmi8998_flash1>;
+ torch-source = <&pmi8998_torch0 &pmi8998_torch1>;
+ switch-source = <&pmi8998_switch0>;
+ status = "ok";
+ };
+
+ led_flash_front: qcom,camera-flash@1 {
+ cell-index = <1>;
+ reg = <0x01 0x00>;
+ compatible = "qcom,camera-flash";
+ flash-source = <&pmi8998_flash2>;
+ torch-source = <&pmi8998_torch2>;
+ switch-source = <&pmi8998_switch1>;
+ status = "ok";
+ };
+
+ actuator_regulator: gpio-regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0x00 0x00>;
+ regulator-name = "actuator_regulator";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <100>;
+ enable-active-high;
+ gpio = <&tlmm 27 0>;
+ vin-supply = <&pmi8998_bob>;
+ };
+
+ camera_rear_ldo: gpio-regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <0x01 0x00>;
+ regulator-name = "camera_rear_ldo";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-enable-ramp-delay = <135>;
+ enable-active-high;
+ gpio = <&pm8998_gpios 12 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&camera_rear_dvdd_en_default>;
+ vin-supply = <&pm8998_s3>;
+ };
+
+ camera_ldo: gpio-regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <0x02 0x00>;
+ regulator-name = "camera_ldo";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-enable-ramp-delay = <233>;
+ enable-active-high;
+ gpio = <&pm8998_gpios 9 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&camera_dvdd_en_default>;
+ vin-supply = <&pm8998_s3>;
+ };
+};
+
+&cam_cci {
+ actuator_rear: qcom,actuator@0 {
+ cell-index = <0>;
+ reg = <0x0>;
+ compatible = "qcom,actuator";
+ cci-master = <0>;
+ cam_vaf-supply = <&actuator_regulator>;
+ regulator-names = "cam_vaf";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <2800000>;
+ rgltr-max-voltage = <2800000>;
+ rgltr-load-current = <0>;
+ };
+
+ actuator_front: qcom,actuator@1 {
+ cell-index = <1>;
+ reg = <0x1>;
+ compatible = "qcom,actuator";
+ cci-master = <1>;
+ cam_vaf-supply = <&actuator_regulator>;
+ regulator-names = "cam_vaf";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <2800000>;
+ rgltr-max-voltage = <2800000>;
+ rgltr-load-current = <0>;
+ };
+
+ ois_rear: qcom,ois@0 {
+ cell-index = <0>;
+ reg = <0x0>;
+ compatible = "qcom,ois";
+ cci-master = <0>;
+ cam_vaf-supply = <&actuator_regulator>;
+ regulator-names = "cam_vaf";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <2800000>;
+ rgltr-max-voltage = <2800000>;
+ rgltr-load-current = <0>;
+ status = "ok";
+ };
+
+ eeprom_rear: qcom,eeprom@0 {
+ cell-index = <0>;
+ reg = <0>;
+ compatible = "qcom,eeprom";
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_rear_ldo>;
+ cam_clk-supply = <&titan_top_gdsc>;
+ regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+ "cam_clk";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <0 3312000 1050000 0>;
+ rgltr-max-voltage = <0 3600000 1050000 0>;
+ rgltr-load-current = <0 80000 105000 0>;
+ gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk0_active
+ &cam_sensor_rear_active>;
+ pinctrl-1 = <&cam_sensor_mclk0_suspend
+ &cam_sensor_rear_suspend>;
+ gpios = <&tlmm 13 0>,
+ <&tlmm 80 0>,
+ <&tlmm 79 0>,
+ <&tlmm 27 0>;
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-vaf = <3>;
+ gpio-req-tbl-num = <0 1 2 3>;
+ gpio-req-tbl-flags = <1 0 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK0",
+ "CAM_RESET0",
+ "CAM_VANA0",
+ "CAM_VAF";
+ sensor-position = <0>;
+ sensor-mode = <0>;
+ cci-master = <0>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+ clock-names = "cam_clk";
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
+ };
+
+ eeprom_rear_aux: qcom,eeprom@1 {
+ cell-index = <1>;
+ reg = <0x1>;
+ compatible = "qcom,eeprom";
+ cam_vdig-supply = <&camera_ldo>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_clk-supply = <&titan_top_gdsc>;
+ regulator-names = "cam_vdig", "cam_vio", "cam_vana",
+ "cam_clk";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <1050000 0 3312000 0>;
+ rgltr-max-voltage = <1050000 0 3600000 0>;
+ rgltr-load-current = <105000 0 80000 0>;
+ gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk2_active
+ &cam_sensor_rear2_active>;
+ pinctrl-1 = <&cam_sensor_mclk2_suspend
+ &cam_sensor_rear2_suspend>;
+ gpios = <&tlmm 15 0>,
+ <&tlmm 9 0>,
+ <&tlmm 8 0>;
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-req-tbl-num = <0 1 2>;
+ gpio-req-tbl-flags = <1 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK1",
+ "CAM_RESET1",
+ "CAM_VANA1";
+ sensor-position = <0>;
+ sensor-mode = <0>;
+ cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ clock-names = "cam_clk";
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
+ };
+
+ eeprom_front: qcom,eeprom@2 {
+ cell-index = <2>;
+ reg = <0x2>;
+ compatible = "qcom,eeprom";
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_ldo>;
+ cam_clk-supply = <&titan_top_gdsc>;
+ regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+ "cam_clk";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <0 2812000 1050000 0>;
+ rgltr-max-voltage = <0 3600000 1050000 0>;
+ rgltr-load-current = <0 80000 105000 0>;
+ gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk2_active
+ &cam_sensor_rear2_active>;
+ pinctrl-1 = <&cam_sensor_mclk2_suspend
+ &cam_sensor_rear2_suspend>;
+ gpios = <&tlmm 15 0>,
+ <&tlmm 9 0>,
+ <&tlmm 8 0>;
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-req-tbl-num = <0 1 2>;
+ gpio-req-tbl-flags = <1 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK2",
+ "CAM_RESET2",
+ "CAM_VANA1";
+ sensor-position = <1>;
+ sensor-mode = <1>;
+ cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ clock-names = "cam_clk";
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
+ };
+
+ qcom,cam-sensor@0 {
+ cell-index = <0>;
+ compatible = "qcom,cam-sensor";
+ reg = <0x0>;
+ csiphy-sd-index = <0>;
+ sensor-position-roll = <270>;
+ sensor-position-pitch = <0>;
+ sensor-position-yaw = <180>;
+ led-flash-src = <&led_flash_rear>;
+ actuator-src = <&actuator_rear>;
+ ois-src = <&ois_rear>;
+ eeprom-src = <&eeprom_rear>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_rear_ldo>;
+ cam_clk-supply = <&titan_top_gdsc>;
+ regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+ "cam_clk";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <0 3312000 1050000 0>;
+ rgltr-max-voltage = <0 3600000 1050000 0>;
+ rgltr-load-current = <0 80000 105000 0>;
+ gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk0_active
+ &cam_sensor_rear_active>;
+ pinctrl-1 = <&cam_sensor_mclk0_suspend
+ &cam_sensor_rear_suspend>;
+ gpios = <&tlmm 13 0>,
+ <&tlmm 80 0>,
+ <&tlmm 79 0>;
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-req-tbl-num = <0 1 2>;
+ gpio-req-tbl-flags = <1 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK0",
+ "CAM_RESET0",
+ "CAM_VANA";
+ sensor-mode = <0>;
+ cci-master = <0>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+ clock-names = "cam_clk";
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
+ };
+
+ qcom,cam-sensor@1 {
+ cell-index = <1>;
+ compatible = "qcom,cam-sensor";
+ reg = <0x1>;
+ csiphy-sd-index = <1>;
+ sensor-position-roll = <90>;
+ sensor-position-pitch = <0>;
+ sensor-position-yaw = <180>;
+ eeprom-src = <&eeprom_rear_aux>;
+ cam_vdig-supply = <&camera_ldo>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_clk-supply = <&titan_top_gdsc>;
+ regulator-names = "cam_vdig", "cam_vio", "cam_vana",
+ "cam_clk";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <1050000 0 3312000 0>;
+ rgltr-max-voltage = <1050000 0 3600000 0>;
+ rgltr-load-current = <105000 0 80000 0>;
+ gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk1_active
+ &cam_sensor_front_active>;
+ pinctrl-1 = <&cam_sensor_mclk1_suspend
+ &cam_sensor_front_suspend>;
+ gpios = <&tlmm 14 0>,
+ <&tlmm 9 0>,
+ <&tlmm 8 0>;
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-req-tbl-num = <0 1 2>;
+ gpio-req-tbl-flags = <1 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK1",
+ "CAM_RESET1",
+ "CAM_VANA1";
+ sensor-mode = <0>;
+ cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ clock-names = "cam_clk";
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
+ };
+
+ qcom,cam-sensor@2 {
+ cell-index = <2>;
+ compatible = "qcom,cam-sensor";
+ reg = <0x02>;
+ csiphy-sd-index = <2>;
+ sensor-position-roll = <90>;
+ sensor-position-pitch = <0>;
+ sensor-position-yaw = <0>;
+ eeprom-src = <&eeprom_front>;
+ actuator-src = <&actuator_front>;
+ led-flash-src = <&led_flash_front>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_ldo>;
+ cam_clk-supply = <&titan_top_gdsc>;
+ regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+ "cam_clk";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <0 2812000 1050000 0>;
+ rgltr-max-voltage = <0 3600000 1050000 0>;
+ rgltr-load-current = <0 80000 105000 0>;
+ gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk2_active
+ &cam_sensor_rear2_active>;
+ pinctrl-1 = <&cam_sensor_mclk2_suspend
+ &cam_sensor_rear2_suspend>;
+ gpios = <&tlmm 15 0>,
+ <&tlmm 9 0>,
+ <&tlmm 8 0>;
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-req-tbl-num = <0 1 2>;
+ gpio-req-tbl-flags = <1 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK2",
+ "CAM_RESET2",
+ "CAM_VANA1";
+ sensor-mode = <1>;
+ cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ clock-names = "cam_clk";
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
+ };
+};
+