diff --git a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt
index cc26080..ce1b223 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt
@@ -1,7 +1,9 @@
 * Generic 8-bits shift register GPIO driver
 
 Required properties:
-- compatible : Should be "fairchild,74hc595"
+- compatible: Should contain one of the following:
+    "fairchild,74hc595"
+    "nxp,74lvc594"
 - reg : chip select number
 - gpio-controller : Marks the device node as a gpio controller.
 - #gpio-cells : Should be two.  The first cell is the pin number and
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
index 120bc49..4b6cc63 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
@@ -1,9 +1,10 @@
-* Freescale MPC512x/MPC8xxx/Layerscape GPIO controller
+* Freescale MPC512x/MPC8xxx/QorIQ/Layerscape GPIO controller
 
 Required properties:
 - compatible : Should be "fsl,<soc>-gpio"
   The following <soc>s are known to be supported:
-    mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq.
+	mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq,
+	ls1021a, ls1043a, ls2080a.
 - reg : Address and length of the register set for the device
 - interrupts : Should be the port interrupt shared by all 32 pins.
 - #gpio-cells : Should be two.  The first cell is the pin number and
@@ -15,7 +16,7 @@
 - little-endian : GPIO registers are used as little endian. If not
                   present registers are used as big endian by default.
 
-Example:
+Example of gpio-controller node for a mpc5125 SoC:
 
 gpio0: gpio@1100 {
 	compatible = "fsl,mpc5125-gpio";
@@ -24,3 +25,16 @@
 	interrupts = <78 0x8>;
 	status = "okay";
 };
+
+Example of gpio-controller node for a ls2080a SoC:
+
+gpio0: gpio@2300000 {
+	compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio";
+	reg = <0x0 0x2300000 0x0 0x10000>;
+	interrupts = <0 36 0x4>; /* Level high type */
+	gpio-controller;
+	little-endian;
+	#gpio-cells = <2>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
index 262ee4d..28662d8 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
@@ -3,6 +3,8 @@
 
 This GPIO driver is used for following Netlogic XLP SoCs:
 	XLP832, XLP316, XLP208, XLP980, XLP532
+This GPIO driver is also compatible with GPIO controller found on
+Broadcom Vulcan ARM64.
 
 Required properties:
 -------------------
@@ -13,6 +15,7 @@
   - "netlogic,xlp208-gpio": For Netlogic XLP208
   - "netlogic,xlp980-gpio": For Netlogic XLP980
   - "netlogic,xlp532-gpio": For Netlogic XLP532
+  - "brcm,vulcan-gpio": For Broadcom Vulcan ARM64
 - reg: Physical base address and length of the controller's registers.
 - #gpio-cells: Should be two. The first cell is the pin number and the second
   cell is used to specify optional parameters (currently unused).
diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
index 069cdf6..68d28f6 100644
--- a/Documentation/devicetree/bindings/gpio/gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio.txt
@@ -131,6 +131,13 @@
 property, and a #gpio-cells integer property, which indicates the number of
 cells in a gpio-specifier.
 
+Some system-on-chips (SoCs) use the concept of GPIO banks. A GPIO bank is an
+instance of a hardware IP core on a silicon die, usually exposed to the
+programmer as a coherent range of I/O addresses. Usually each such bank is
+exposed in the device tree as an individual gpio-controller node, reflecting
+the fact that the hardware was synthesized by reusing the same IP block a
+few times over.
+
 Optionally, a GPIO controller may have a "ngpios" property. This property
 indicates the number of in-use slots of available slots for GPIOs. The
 typical example is something like this: the hardware register is 32 bits
@@ -145,6 +152,21 @@
 and which are dummies. The bindings for this case has not yet been
 specified, but should be specified if/when such hardware appears.
 
+Optionally, a GPIO controller may have a "gpio-line-names" property. This is
+an array of strings defining the names of the GPIO lines going out of the
+GPIO controller. This name should be the most meaningful producer name
+for the system, such as a rail name indicating the usage. Package names
+such as pin name are discouraged: such lines have opaque names (since they
+are by definition generic purpose) and such names are usually not very
+helpful. For example "MMC-CD", "Red LED Vdd" and "ethernet reset" are
+reasonable line names as they describe what the line is used for. "GPIO0"
+is not a good name to give to a GPIO line. Placeholders are discouraged:
+rather use the "" (blank string) if the use of the GPIO line is undefined
+in your design. The names are assigned starting from line offset 0 from
+left to right from the passed array. An incomplete array (where the number
+of passed named are less than ngpios) will still be used up until the last
+provided valid line index.
+
 Example:
 
 gpio-controller@00000000 {
@@ -153,6 +175,10 @@
 	gpio-controller;
 	#gpio-cells = <2>;
 	ngpios = <18>;
+	gpio-line-names = "MMC-CD", "MMC-WP", "VDD eth", "RST eth", "LED R",
+		"LED G", "LED B", "Col A", "Col B", "Col C", "Col D",
+		"Row A", "Row B", "Row C", "Row D", "NMI button",
+		"poweroff", "reset";
 }
 
 The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism
diff --git a/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt
new file mode 100644
index 0000000..038c3a6
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt
@@ -0,0 +1,38 @@
+Bindings for the Western Digital's MyBook Live memory-mapped GPIO controllers.
+
+The Western Digital MyBook Live has two memory-mapped GPIO controllers.
+Both GPIO controller only have a single 8-bit data register, where GPIO
+state can be read and/or written.
+
+Required properties:
+	- compatible: should be "wd,mbl-gpio"
+	- reg-names: must contain
+		"dat" - data register
+	- reg: address + size pairs describing the GPIO register sets;
+		order must correspond with the order of entries in reg-names
+	- #gpio-cells: must be set to 2. The first cell is the pin number and
+			the second cell is used to specify the gpio polarity:
+			0 = active high
+			1 = active low
+	- gpio-controller: Marks the device node as a gpio controller.
+
+Optional properties:
+	- no-output: GPIOs are read-only.
+
+Examples:
+	gpio0: gpio0@e0000000 {
+		compatible = "wd,mbl-gpio";
+		reg-names = "dat";
+		reg = <0xe0000000 0x1>;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+
+	gpio1: gpio1@e0100000 {
+		compatible = "wd,mbl-gpio";
+		reg-names = "dat";
+		reg = <0xe0100000 0x1>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		no-output;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt
similarity index 100%
rename from Documentation/devicetree/bindings/gpio/gpio-poweroff.txt
rename to Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt
diff --git a/Documentation/devicetree/bindings/gpio/gpio-restart.txt b/Documentation/devicetree/bindings/power/reset/gpio-restart.txt
similarity index 100%
rename from Documentation/devicetree/bindings/gpio/gpio-restart.txt
rename to Documentation/devicetree/bindings/power/reset/gpio-restart.txt
diff --git a/Documentation/gpio/driver.txt b/Documentation/gpio/driver.txt
index bbeec41..6cb35a7 100644
--- a/Documentation/gpio/driver.txt
+++ b/Documentation/gpio/driver.txt
@@ -68,6 +68,103 @@
 on -RT (inside hard IRQ handlers and similar contexts). Normally this should
 not be required.
 
+
+GPIOs with open drain/source support
+------------------------------------
+
+Open drain (CMOS) or open collector (TTL) means the line is not actively driven
+high: instead you provide the drain/collector as output, so when the transistor
+is not open, it will present a high-impedance (tristate) to the external rail.
+
+
+   CMOS CONFIGURATION      TTL CONFIGURATION
+
+            ||--- out              +--- out
+     in ----||                   |/
+            ||--+         in ----|
+                |                |\
+               GND	           GND
+
+This configuration is normally used as a way to achieve one of two things:
+
+- Level-shifting: to reach a logical level higher than that of the silicon
+  where the output resides.
+
+- inverse wire-OR on an I/O line, for example a GPIO line, making it possible
+  for any driving stage on the line to drive it low even if any other output
+  to the same line is simultaneously driving it high. A special case of this
+  is driving the SCL and SCA lines of an I2C bus, which is by definition a
+  wire-OR bus.
+
+Both usecases require that the line be equipped with a pull-up resistor. This
+resistor will make the line tend to high level unless one of the transistors on
+the rail actively pulls it down.
+
+The level on the line will go as high as the VDD on the pull-up resistor, which
+may be higher than the level supported by the transistor, achieveing a
+level-shift to the higher VDD.
+
+Integrated electronics often have an output driver stage in the form of a CMOS
+"totem-pole" with one N-MOS and one P-MOS transistor where one of them drives
+the line high and one of them drives the line low. This is called a push-pull
+output. The "totem-pole" looks like so:
+
+                 VDD
+                  |
+        OD    ||--+
+     +--/ ---o||     P-MOS-FET
+     |        ||--+
+IN --+            +----- out
+     |        ||--+
+     +--/ ----||     N-MOS-FET
+        OS    ||--+
+                  |
+                 GND
+
+The desired output signal (e.g. coming directly from some GPIO output register)
+arrives at IN. The switches named "OD" and "OS" are normally closed, creating
+a push-pull circuit.
+
+Consider the little "switches" named "OD" and "OS" that enable/disable the
+P-MOS or N-MOS transistor right after the split of the input. As you can see,
+either transistor will go totally numb if this switch is open. The totem-pole
+is then halved and give high impedance instead of actively driving the line
+high or low respectively. That is usually how software-controlled open
+drain/source works.
+
+Some GPIO hardware come in open drain / open source configuration. Some are
+hard-wired lines that will only support open drain or open source no matter
+what: there is only one transistor there. Some are software-configurable:
+by flipping a bit in a register the output can be configured as open drain
+or open source, in practice by flicking open the switches labeled "OD" and "OS"
+in the drawing above.
+
+By disabling the P-MOS transistor, the output can be driven between GND and
+high impedance (open drain), and by disabling the N-MOS transistor, the output
+can be driven between VDD and high impedance (open source). In the first case,
+a pull-up resistor is needed on the outgoing rail to complete the circuit, and
+in the second case, a pull-down resistor is needed on the rail.
+
+Hardware that supports open drain or open source or both, can implement a
+special callback in the gpio_chip: .set_single_ended() that takes an enum flag
+telling whether to configure the line as open drain, open source or push-pull.
+This will happen in response to the GPIO_OPEN_DRAIN or GPIO_OPEN_SOURCE flag
+set in the machine file, or coming from other hardware descriptions.
+
+If this state can not be configured in hardware, i.e. if the GPIO hardware does
+not support open drain/open source in hardware, the GPIO library will instead
+use a trick: when a line is set as output, if the line is flagged as open
+drain, and the IN output value is low, it will be driven low as usual. But
+if the IN output value is set to high, it will instead *NOT* be driven high,
+instead it will be switched to input, as input mode is high impedance, thus
+achieveing an "open drain emulation" of sorts: electrically the behaviour will
+be identical, with the exception of possible hardware glitches when switching
+the mode of the line.
+
+For open source configuration the same principle is used, just that instead
+of actively driving the line low, it is set to input.
+
+
 GPIO drivers providing IRQs
 ---------------------------
 It is custom that GPIO drivers (GPIO chips) are also providing interrupts,
diff --git a/MAINTAINERS b/MAINTAINERS
index 1dd9335..8267754 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4902,6 +4902,7 @@
 L:	linux-gpio@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio.git
 S:	Maintained
+F:	Documentation/devicetree/bindings/gpio/
 F:	Documentation/gpio/
 F:	Documentation/ABI/testing/gpio-cdev
 F:	Documentation/ABI/obsolete/sysfs-gpio
diff --git a/arch/alpha/Kconfig b/arch/alpha/Kconfig
index 9d8a858..fe99f89 100644
--- a/arch/alpha/Kconfig
+++ b/arch/alpha/Kconfig
@@ -13,7 +13,6 @@
 	select GENERIC_IRQ_PROBE
 	select AUTO_IRQ_AFFINITY if SMP
 	select GENERIC_IRQ_SHOW
-	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select ARCH_WANT_IPC_PARSE_VERSION
 	select ARCH_HAVE_NMI_SAFE_CMPXCHG
 	select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE
diff --git a/arch/arc/plat-axs10x/Kconfig b/arch/arc/plat-axs10x/Kconfig
index 426ac4b..c54d1ae 100644
--- a/arch/arc/plat-axs10x/Kconfig
+++ b/arch/arc/plat-axs10x/Kconfig
@@ -13,7 +13,7 @@
 	select OF_GPIO
 	select MIGHT_HAVE_PCI
 	select GENERIC_IRQ_CHIP
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	help
 	  Support for the ARC AXS10x Software Development Platforms.
 
diff --git a/arch/arc/plat-tb10x/Kconfig b/arch/arc/plat-tb10x/Kconfig
index d14b3d3..149e091 100644
--- a/arch/arc/plat-tb10x/Kconfig
+++ b/arch/arc/plat-tb10x/Kconfig
@@ -21,7 +21,7 @@
 	select PINCTRL
 	select PINCTRL_TB10X
 	select PINMUX
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select GPIO_TB10X
 	select TB10X_IRQC
 	help
diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig
index b6878eb..18b8877 100644
--- a/arch/avr32/Kconfig
+++ b/arch/avr32/Kconfig
@@ -74,7 +74,7 @@
 	select SUBARCH_AVR32B
 	select MMU
 	select PERFORMANCE_COUNTERS
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select GENERIC_ALLOCATOR
 	select HAVE_FB_ATMEL
 
diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig
index e086f9e..99bda1b 100644
--- a/arch/cris/Kconfig
+++ b/arch/cris/Kconfig
@@ -61,7 +61,7 @@
 	select CLONE_BACKWARDS2
 	select OLD_SIGSUSPEND
 	select OLD_SIGACTION
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select IRQ_DOMAIN if ETRAX_ARCH_V32
 	select OF if ETRAX_ARCH_V32
 	select OF_EARLY_FLATTREE if ETRAX_ARCH_V32
diff --git a/arch/m68k/Kconfig.cpu b/arch/m68k/Kconfig.cpu
index 0dfcf12..c1beb5a 100644
--- a/arch/m68k/Kconfig.cpu
+++ b/arch/m68k/Kconfig.cpu
@@ -22,11 +22,11 @@
 
 config COLDFIRE
 	bool "Coldfire CPU family support"
-	select ARCH_REQUIRE_GPIOLIB
 	select ARCH_HAVE_CUSTOM_GPIO_H
 	select CPU_HAS_NO_BITFIELDS
 	select CPU_HAS_NO_MULDIV64
 	select GENERIC_CSUM
+	select GPIOLIB
 	select HAVE_CLK
 
 endchoice
diff --git a/arch/metag/Kconfig.soc b/arch/metag/Kconfig.soc
index 973640f..50f979c 100644
--- a/arch/metag/Kconfig.soc
+++ b/arch/metag/Kconfig.soc
@@ -16,7 +16,6 @@
 
 config SOC_TZ1090
 	bool "Toumaz Xenif TZ1090 SoC (Comet)"
-	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select IMGPDC_IRQ
 	select METAG_LNKGET_AROUND_CACHE
 	select METAG_META21
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 3ee1ea6..d2ac117 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -79,7 +79,7 @@
 	select SYS_HAS_CPU_MIPS32_R1
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select SYS_SUPPORTS_APM_EMULATION
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select SYS_SUPPORTS_ZBOOT
 	select COMMON_CLK
 
@@ -98,7 +98,7 @@
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_SUPPORTS_MIPS16
 	select SYS_SUPPORTS_ZBOOT_UART16550
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select VLYNQ
 	select HAVE_CLK
 	help
@@ -122,11 +122,11 @@
 config ATH79
 	bool "Atheros AR71XX/AR724X/AR913X based boards"
 	select ARCH_HAS_RESET_CONTROLLER
-	select ARCH_REQUIRE_GPIOLIB
 	select BOOT_RAW
 	select CEVT_R4K
 	select CSRC_R4K
 	select DMA_NONCOHERENT
+	select GPIOLIB
 	select HAVE_CLK
 	select COMMON_CLK
 	select CLKDEV_LOOKUP
@@ -170,7 +170,6 @@
 	select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
 	select USB_OHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
 	select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
-	select ARCH_WANT_OPTIONAL_GPIOLIB
 	help
 	  Build a generic DT-based kernel image that boots on select
 	  BCM33xx cable modem chips, BCM63xx DSL chips, and BCM7xxx set-top
@@ -179,7 +178,6 @@
 
 config BCM47XX
 	bool "Broadcom BCM47XX based boards"
-	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select BOOT_RAW
 	select CEVT_R4K
 	select CSRC_R4K
@@ -211,7 +209,7 @@
 	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_HAS_EARLY_PRINTK
 	select SWAP_IO_SPACE
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select HAVE_CLK
 	select MIPS_L1_CACHE_SHIFT_4
 	help
@@ -305,7 +303,7 @@
 	select SYS_SUPPORTS_ZBOOT_UART16550
 	select DMA_NONCOHERENT
 	select IRQ_MIPS_CPU
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select COMMON_CLK
 	select GENERIC_IRQ_CHIP
 	select BUILTIN_DTB
@@ -325,7 +323,7 @@
 	select SYS_SUPPORTS_MIPS16
 	select SYS_SUPPORTS_MULTITHREADING
 	select SYS_HAS_EARLY_PRINTK
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select SWAP_IO_SPACE
 	select BOOT_RAW
 	select CLKDEV_LOOKUP
@@ -377,7 +375,6 @@
 
 config MACH_PISTACHIO
 	bool "IMG Pistachio SoC based boards"
-	select ARCH_REQUIRE_GPIOLIB
 	select BOOT_ELF32
 	select BOOT_RAW
 	select CEVT_R4K
@@ -385,6 +382,7 @@
 	select COMMON_CLK
 	select CSRC_R4K
 	select DMA_MAYBE_COHERENT
+	select GPIOLIB
 	select IRQ_MIPS_CPU
 	select LIBFDT
 	select MFD_SYSCON
@@ -406,13 +404,13 @@
 
 config MACH_XILFPGA
 	bool "MIPSfpga Xilinx based boards"
-	select ARCH_REQUIRE_GPIOLIB
 	select BOOT_ELF32
 	select BOOT_RAW
 	select BUILTIN_DTB
 	select CEVT_R4K
 	select COMMON_CLK
 	select CSRC_R4K
+	select GPIOLIB
 	select IRQ_MIPS_CPU
 	select LIBFDT
 	select MIPS_CPU_SCACHE
@@ -536,7 +534,7 @@
 	select CSRC_R4K
 	select SYS_HAS_CPU_VR41XX
 	select SYS_SUPPORTS_MIPS16
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 
 config NXP_STB220
 	bool "NXP STB220 board"
@@ -856,7 +854,7 @@
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SWAP_IO_SPACE
 	select BOOT_RAW
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select MIPS_L1_CACHE_SHIFT_4
 	help
 	  Support the Mikrotik(tm) RouterBoard 532 series,
@@ -879,7 +877,7 @@
 	select HW_HAS_PCI
 	select ZONE_DMA32
 	select HOLES_IN_ZONE
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select LIBFDT
 	select USE_OF
 	select ARCH_SPARSEMEM_ENABLE
@@ -937,7 +935,7 @@
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select SYS_SUPPORTS_64BIT_KERNEL
 	select ARCH_PHYS_ADDR_T_64BIT
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_SUPPORTS_HIGHMEM
@@ -1077,7 +1075,7 @@
 	def_bool CSRC_R4K || CLKSRC_MIPS_GIC
 
 config GPIO_TXX9
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	bool
 
 config FW_CFE
@@ -1342,7 +1340,7 @@
 	select CPU_SUPPORTS_HUGEPAGES
 	select WEAK_ORDERING
 	select WEAK_REORDERING_BEYOND_LLSC
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	help
 		The Loongson 3 processor implements the MIPS64R2 instruction
 		set with many extensions.
@@ -1362,7 +1360,7 @@
 	bool "Loongson 2F"
 	depends on SYS_HAS_CPU_LOONGSON2F
 	select CPU_LOONGSON2
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	help
 	  The Loongson 2F processor implements the MIPS III instruction set
 	  with many extensions.
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index 7fa2488..88b4d6a 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -20,7 +20,7 @@
 
 config MIPS_DB1XXX
 	bool "Alchemy DB1XXX / PB1XXX boards"
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select HW_HAS_PCI
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select SYS_HAS_EARLY_PRINTK
diff --git a/arch/mips/pic32/Kconfig b/arch/mips/pic32/Kconfig
index 1985971..527d37d 100644
--- a/arch/mips/pic32/Kconfig
+++ b/arch/mips/pic32/Kconfig
@@ -14,7 +14,7 @@
 	select SYS_HAS_EARLY_PRINTK
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select SYS_SUPPORTS_LITTLE_ENDIAN
-	select ARCH_REQUIRE_GPIOLIB
+	select GPIOLIB
 	select COMMON_CLK
 	select CLKDEV_LOOKUP
 	select LIBFDT
diff --git a/arch/nios2/Kconfig b/arch/nios2/Kconfig
index 4375554..87ca653 100644
--- a/arch/nios2/Kconfig
+++ b/arch/nios2/Kconfig
@@ -1,6 +1,5 @@
 config NIOS2
 	def_bool y
-	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select CLKSRC_OF
 	select GENERIC_ATOMIC64
 	select GENERIC_CLOCKEVENTS
diff --git a/arch/powerpc/platforms/52xx/mpc52xx_gpt.c b/arch/powerpc/platforms/52xx/mpc52xx_gpt.c
index 3048e34..22645a7 100644
--- a/arch/powerpc/platforms/52xx/mpc52xx_gpt.c
+++ b/arch/powerpc/platforms/52xx/mpc52xx_gpt.c
@@ -278,14 +278,9 @@
  * GPIOLIB hooks
  */
 #if defined(CONFIG_GPIOLIB)
-static inline struct mpc52xx_gpt_priv *gc_to_mpc52xx_gpt(struct gpio_chip *gc)
-{
-	return container_of(gc, struct mpc52xx_gpt_priv, gc);
-}
-
 static int mpc52xx_gpt_gpio_get(struct gpio_chip *gc, unsigned int gpio)
 {
-	struct mpc52xx_gpt_priv *gpt = gc_to_mpc52xx_gpt(gc);
+	struct mpc52xx_gpt_priv *gpt = gpiochip_get_data(gc);
 
 	return (in_be32(&gpt->regs->status) >> 8) & 1;
 }
@@ -293,7 +288,7 @@
 static void
 mpc52xx_gpt_gpio_set(struct gpio_chip *gc, unsigned int gpio, int v)
 {
-	struct mpc52xx_gpt_priv *gpt = gc_to_mpc52xx_gpt(gc);
+	struct mpc52xx_gpt_priv *gpt = gpiochip_get_data(gc);
 	unsigned long flags;
 	u32 r;
 
@@ -307,7 +302,7 @@
 
 static int mpc52xx_gpt_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
 {
-	struct mpc52xx_gpt_priv *gpt = gc_to_mpc52xx_gpt(gc);
+	struct mpc52xx_gpt_priv *gpt = gpiochip_get_data(gc);
 	unsigned long flags;
 
 	dev_dbg(gpt->dev, "%s: gpio:%d\n", __func__, gpio);
@@ -354,9 +349,9 @@
 	clrsetbits_be32(&gpt->regs->mode, MPC52xx_GPT_MODE_MS_MASK,
 			MPC52xx_GPT_MODE_MS_GPIO);
 
-	rc = gpiochip_add(&gpt->gc);
+	rc = gpiochip_add_data(&gpt->gc, gpt);
 	if (rc)
-		dev_err(gpt->dev, "gpiochip_add() failed; rc=%i\n", rc);
+		dev_err(gpt->dev, "gpiochip_add_data() failed; rc=%i\n", rc);
 
 	dev_dbg(gpt->dev, "%s() complete.\n", __func__);
 }
diff --git a/arch/powerpc/platforms/83xx/mcu_mpc8349emitx.c b/arch/powerpc/platforms/83xx/mcu_mpc8349emitx.c
index 15e8021..dbcd030 100644
--- a/arch/powerpc/platforms/83xx/mcu_mpc8349emitx.c
+++ b/arch/powerpc/platforms/83xx/mcu_mpc8349emitx.c
@@ -16,7 +16,7 @@
 #include <linux/device.h>
 #include <linux/mutex.h>
 #include <linux/i2c.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/of.h>
 #include <linux/of_gpio.h>
 #include <linux/slab.h>
@@ -99,7 +99,7 @@
 
 static void mcu_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
 {
-	struct mcu *mcu = container_of(gc, struct mcu, gc);
+	struct mcu *mcu = gpiochip_get_data(gc);
 	u8 bit = 1 << (4 + gpio);
 
 	mutex_lock(&mcu->lock);
@@ -136,7 +136,7 @@
 	gc->direction_output = mcu_gpio_dir_out;
 	gc->of_node = np;
 
-	return gpiochip_add(gc);
+	return gpiochip_add_data(gc, mcu);
 }
 
 static int mcu_gpiochip_remove(struct mcu *mcu)
diff --git a/arch/powerpc/sysdev/cpm1.c b/arch/powerpc/sysdev/cpm1.c
index 8ed6536..6c11099 100644
--- a/arch/powerpc/sysdev/cpm1.c
+++ b/arch/powerpc/sysdev/cpm1.c
@@ -532,15 +532,9 @@
 	u16 cpdata;
 };
 
-static inline struct cpm1_gpio16_chip *
-to_cpm1_gpio16_chip(struct of_mm_gpio_chip *mm_gc)
-{
-	return container_of(mm_gc, struct cpm1_gpio16_chip, mm_gc);
-}
-
 static void cpm1_gpio16_save_regs(struct of_mm_gpio_chip *mm_gc)
 {
-	struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc);
+	struct cpm1_gpio16_chip *cpm1_gc = gpiochip_get_data(&mm_gc->gc);
 	struct cpm_ioport16 __iomem *iop = mm_gc->regs;
 
 	cpm1_gc->cpdata = in_be16(&iop->dat);
@@ -560,7 +554,7 @@
 static void __cpm1_gpio16_set(struct of_mm_gpio_chip *mm_gc, u16 pin_mask,
 	int value)
 {
-	struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc);
+	struct cpm1_gpio16_chip *cpm1_gc = gpiochip_get_data(&mm_gc->gc);
 	struct cpm_ioport16 __iomem *iop = mm_gc->regs;
 
 	if (value)
@@ -574,7 +568,7 @@
 static void cpm1_gpio16_set(struct gpio_chip *gc, unsigned int gpio, int value)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc);
+	struct cpm1_gpio16_chip *cpm1_gc = gpiochip_get_data(&mm_gc->gc);
 	unsigned long flags;
 	u16 pin_mask = 1 << (15 - gpio);
 
@@ -588,7 +582,7 @@
 static int cpm1_gpio16_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc);
+	struct cpm1_gpio16_chip *cpm1_gc = gpiochip_get_data(&mm_gc->gc);
 	struct cpm_ioport16 __iomem *iop = mm_gc->regs;
 	unsigned long flags;
 	u16 pin_mask = 1 << (15 - gpio);
@@ -606,7 +600,7 @@
 static int cpm1_gpio16_dir_in(struct gpio_chip *gc, unsigned int gpio)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc);
+	struct cpm1_gpio16_chip *cpm1_gc = gpiochip_get_data(&mm_gc->gc);
 	struct cpm_ioport16 __iomem *iop = mm_gc->regs;
 	unsigned long flags;
 	u16 pin_mask = 1 << (15 - gpio);
@@ -642,7 +636,7 @@
 	gc->get = cpm1_gpio16_get;
 	gc->set = cpm1_gpio16_set;
 
-	return of_mm_gpiochip_add(np, mm_gc);
+	return of_mm_gpiochip_add_data(np, mm_gc, cpm1_gc);
 }
 
 struct cpm1_gpio32_chip {
@@ -653,15 +647,9 @@
 	u32 cpdata;
 };
 
-static inline struct cpm1_gpio32_chip *
-to_cpm1_gpio32_chip(struct of_mm_gpio_chip *mm_gc)
-{
-	return container_of(mm_gc, struct cpm1_gpio32_chip, mm_gc);
-}
-
 static void cpm1_gpio32_save_regs(struct of_mm_gpio_chip *mm_gc)
 {
-	struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc);
+	struct cpm1_gpio32_chip *cpm1_gc = gpiochip_get_data(&mm_gc->gc);
 	struct cpm_ioport32b __iomem *iop = mm_gc->regs;
 
 	cpm1_gc->cpdata = in_be32(&iop->dat);
@@ -681,7 +669,7 @@
 static void __cpm1_gpio32_set(struct of_mm_gpio_chip *mm_gc, u32 pin_mask,
 	int value)
 {
-	struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc);
+	struct cpm1_gpio32_chip *cpm1_gc = gpiochip_get_data(&mm_gc->gc);
 	struct cpm_ioport32b __iomem *iop = mm_gc->regs;
 
 	if (value)
@@ -695,7 +683,7 @@
 static void cpm1_gpio32_set(struct gpio_chip *gc, unsigned int gpio, int value)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc);
+	struct cpm1_gpio32_chip *cpm1_gc = gpiochip_get_data(&mm_gc->gc);
 	unsigned long flags;
 	u32 pin_mask = 1 << (31 - gpio);
 
@@ -709,7 +697,7 @@
 static int cpm1_gpio32_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc);
+	struct cpm1_gpio32_chip *cpm1_gc = gpiochip_get_data(&mm_gc->gc);
 	struct cpm_ioport32b __iomem *iop = mm_gc->regs;
 	unsigned long flags;
 	u32 pin_mask = 1 << (31 - gpio);
@@ -727,7 +715,7 @@
 static int cpm1_gpio32_dir_in(struct gpio_chip *gc, unsigned int gpio)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc);
+	struct cpm1_gpio32_chip *cpm1_gc = gpiochip_get_data(&mm_gc->gc);
 	struct cpm_ioport32b __iomem *iop = mm_gc->regs;
 	unsigned long flags;
 	u32 pin_mask = 1 << (31 - gpio);
@@ -763,7 +751,7 @@
 	gc->get = cpm1_gpio32_get;
 	gc->set = cpm1_gpio32_set;
 
-	return of_mm_gpiochip_add(np, mm_gc);
+	return of_mm_gpiochip_add_data(np, mm_gc, cpm1_gc);
 }
 
 static int cpm_init_par_io(void)
diff --git a/arch/powerpc/sysdev/cpm_common.c b/arch/powerpc/sysdev/cpm_common.c
index 9d32465..0ac12e5 100644
--- a/arch/powerpc/sysdev/cpm_common.c
+++ b/arch/powerpc/sysdev/cpm_common.c
@@ -80,15 +80,9 @@
 	u32 cpdata;
 };
 
-static inline struct cpm2_gpio32_chip *
-to_cpm2_gpio32_chip(struct of_mm_gpio_chip *mm_gc)
-{
-	return container_of(mm_gc, struct cpm2_gpio32_chip, mm_gc);
-}
-
 static void cpm2_gpio32_save_regs(struct of_mm_gpio_chip *mm_gc)
 {
-	struct cpm2_gpio32_chip *cpm2_gc = to_cpm2_gpio32_chip(mm_gc);
+	struct cpm2_gpio32_chip *cpm2_gc = gpiochip_get_data(&mm_gc->gc);
 	struct cpm2_ioports __iomem *iop = mm_gc->regs;
 
 	cpm2_gc->cpdata = in_be32(&iop->dat);
@@ -108,7 +102,7 @@
 static void __cpm2_gpio32_set(struct of_mm_gpio_chip *mm_gc, u32 pin_mask,
 	int value)
 {
-	struct cpm2_gpio32_chip *cpm2_gc = to_cpm2_gpio32_chip(mm_gc);
+	struct cpm2_gpio32_chip *cpm2_gc = gpiochip_get_data(&mm_gc->gc);
 	struct cpm2_ioports __iomem *iop = mm_gc->regs;
 
 	if (value)
@@ -122,7 +116,7 @@
 static void cpm2_gpio32_set(struct gpio_chip *gc, unsigned int gpio, int value)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct cpm2_gpio32_chip *cpm2_gc = to_cpm2_gpio32_chip(mm_gc);
+	struct cpm2_gpio32_chip *cpm2_gc = gpiochip_get_data(gc);
 	unsigned long flags;
 	u32 pin_mask = 1 << (31 - gpio);
 
@@ -136,7 +130,7 @@
 static int cpm2_gpio32_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct cpm2_gpio32_chip *cpm2_gc = to_cpm2_gpio32_chip(mm_gc);
+	struct cpm2_gpio32_chip *cpm2_gc = gpiochip_get_data(gc);
 	struct cpm2_ioports __iomem *iop = mm_gc->regs;
 	unsigned long flags;
 	u32 pin_mask = 1 << (31 - gpio);
@@ -154,7 +148,7 @@
 static int cpm2_gpio32_dir_in(struct gpio_chip *gc, unsigned int gpio)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct cpm2_gpio32_chip *cpm2_gc = to_cpm2_gpio32_chip(mm_gc);
+	struct cpm2_gpio32_chip *cpm2_gc = gpiochip_get_data(gc);
 	struct cpm2_ioports __iomem *iop = mm_gc->regs;
 	unsigned long flags;
 	u32 pin_mask = 1 << (31 - gpio);
@@ -190,6 +184,6 @@
 	gc->get = cpm2_gpio32_get;
 	gc->set = cpm2_gpio32_set;
 
-	return of_mm_gpiochip_add(np, mm_gc);
+	return of_mm_gpiochip_add_data(np, mm_gc, cpm2_gc);
 }
 #endif /* CONFIG_CPM2 || CONFIG_8xx_GPIO */
diff --git a/arch/powerpc/sysdev/ppc4xx_gpio.c b/arch/powerpc/sysdev/ppc4xx_gpio.c
index d7a7ef13..5382d04 100644
--- a/arch/powerpc/sysdev/ppc4xx_gpio.c
+++ b/arch/powerpc/sysdev/ppc4xx_gpio.c
@@ -27,7 +27,7 @@
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/of_gpio.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/types.h>
 #include <linux/slab.h>
 
@@ -67,12 +67,6 @@
  * There are a maximum of 32 gpios in each gpio controller.
  */
 
-static inline struct ppc4xx_gpio_chip *
-to_ppc4xx_gpiochip(struct of_mm_gpio_chip *mm_gc)
-{
-	return container_of(mm_gc, struct ppc4xx_gpio_chip, mm_gc);
-}
-
 static int ppc4xx_gpio_get(struct gpio_chip *gc, unsigned int gpio)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
@@ -96,8 +90,7 @@
 static void
 ppc4xx_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
 {
-	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct ppc4xx_gpio_chip *chip = to_ppc4xx_gpiochip(mm_gc);
+	struct ppc4xx_gpio_chip *chip = gpiochip_get_data(gc);
 	unsigned long flags;
 
 	spin_lock_irqsave(&chip->lock, flags);
@@ -112,7 +105,7 @@
 static int ppc4xx_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct ppc4xx_gpio_chip *chip = to_ppc4xx_gpiochip(mm_gc);
+	struct ppc4xx_gpio_chip *chip = gpiochip_get_data(gc);
 	struct ppc4xx_gpio __iomem *regs = mm_gc->regs;
 	unsigned long flags;
 
@@ -142,7 +135,7 @@
 ppc4xx_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct ppc4xx_gpio_chip *chip = to_ppc4xx_gpiochip(mm_gc);
+	struct ppc4xx_gpio_chip *chip = gpiochip_get_data(gc);
 	struct ppc4xx_gpio __iomem *regs = mm_gc->regs;
 	unsigned long flags;
 
@@ -200,7 +193,7 @@
 		gc->get = ppc4xx_gpio_get;
 		gc->set = ppc4xx_gpio_set;
 
-		ret = of_mm_gpiochip_add(np, mm_gc);
+		ret = of_mm_gpiochip_add_data(np, mm_gc, ppc4xx_gc);
 		if (ret)
 			goto err;
 		continue;
diff --git a/arch/powerpc/sysdev/simple_gpio.c b/arch/powerpc/sysdev/simple_gpio.c
index 56ce8ca..ef470b4 100644
--- a/arch/powerpc/sysdev/simple_gpio.c
+++ b/arch/powerpc/sysdev/simple_gpio.c
@@ -19,7 +19,7 @@
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/of_gpio.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/slab.h>
 #include <asm/prom.h>
 #include "simple_gpio.h"
@@ -32,11 +32,6 @@
 	u8 data;
 };
 
-static struct u8_gpio_chip *to_u8_gpio_chip(struct of_mm_gpio_chip *mm_gc)
-{
-	return container_of(mm_gc, struct u8_gpio_chip, mm_gc);
-}
-
 static u8 u8_pin2mask(unsigned int pin)
 {
 	return 1 << (8 - 1 - pin);
@@ -52,7 +47,7 @@
 static void u8_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct u8_gpio_chip *u8_gc = to_u8_gpio_chip(mm_gc);
+	struct u8_gpio_chip *u8_gc = gpiochip_get_data(gc);
 	unsigned long flags;
 
 	spin_lock_irqsave(&u8_gc->lock, flags);
@@ -80,7 +75,7 @@
 
 static void u8_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
 {
-	struct u8_gpio_chip *u8_gc = to_u8_gpio_chip(mm_gc);
+	struct u8_gpio_chip *u8_gc = gpiochip_get_data(&mm_gc->gc);
 
 	u8_gc->data = in_8(mm_gc->regs);
 }
@@ -108,7 +103,7 @@
 	gc->get = u8_gpio_get;
 	gc->set = u8_gpio_set;
 
-	ret = of_mm_gpiochip_add(np, mm_gc);
+	ret = of_mm_gpiochip_add_data(np, mm_gc, u8_gc);
 	if (ret)
 		goto err;
 	return 0;
diff --git a/arch/sh/boards/mach-sdk7786/gpio.c b/arch/sh/boards/mach-sdk7786/gpio.c
index f71ce09..4799701 100644
--- a/arch/sh/boards/mach-sdk7786/gpio.c
+++ b/arch/sh/boards/mach-sdk7786/gpio.c
@@ -9,7 +9,7 @@
  */
 #include <linux/init.h>
 #include <linux/interrupt.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/irq.h>
 #include <linux/kernel.h>
 #include <linux/spinlock.h>
@@ -44,6 +44,6 @@
 
 static int __init usrgpir_gpio_setup(void)
 {
-	return gpiochip_add(&usrgpir_gpio_chip);
+	return gpiochip_add_data(&usrgpir_gpio_chip, NULL);
 }
 device_initcall(usrgpir_gpio_setup);
diff --git a/arch/sh/boards/mach-x3proto/gpio.c b/arch/sh/boards/mach-x3proto/gpio.c
index 1fb2cbe..cea88b0 100644
--- a/arch/sh/boards/mach-x3proto/gpio.c
+++ b/arch/sh/boards/mach-x3proto/gpio.c
@@ -13,7 +13,7 @@
 
 #include <linux/init.h>
 #include <linux/interrupt.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/irq.h>
 #include <linux/kernel.h>
 #include <linux/spinlock.h>
@@ -107,7 +107,7 @@
 	if (unlikely(ilsel < 0))
 		return ilsel;
 
-	ret = gpiochip_add(&x3proto_gpio_chip);
+	ret = gpiochip_add_data(&x3proto_gpio_chip, NULL);
 	if (unlikely(ret))
 		goto err_gpio;
 
diff --git a/arch/sparc/Kconfig b/arch/sparc/Kconfig
index d500381..db0a26c 100644
--- a/arch/sparc/Kconfig
+++ b/arch/sparc/Kconfig
@@ -21,7 +21,6 @@
 	select HAVE_ARCH_KGDB if !SMP || SPARC64
 	select HAVE_ARCH_TRACEHOOK
 	select SYSCTL_EXCEPTION_TRACE
-	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE
 	select RTC_CLASS
 	select RTC_DRV_M48T59
diff --git a/arch/unicore32/kernel/gpio.c b/arch/unicore32/kernel/gpio.c
index 5ab2379..49347a0 100644
--- a/arch/unicore32/kernel/gpio.c
+++ b/arch/unicore32/kernel/gpio.c
@@ -14,6 +14,8 @@
 
 #include <linux/init.h>
 #include <linux/module.h>
+#include <linux/gpio/driver.h>
+/* FIXME: needed for gpio_set_value() - convert to use descriptors or hogs */
 #include <linux/gpio.h>
 #include <mach/hardware.h>
 
@@ -118,5 +120,5 @@
  *	gpio_set_value(GPO_SET_V2, 1);
  */
 #endif
-	gpiochip_add(&puv3_gpio_chip);
+	gpiochip_add_data(&puv3_gpio_chip, NULL);
 }
diff --git a/arch/xtensa/Kconfig b/arch/xtensa/Kconfig
index e832d3e..85257af 100644
--- a/arch/xtensa/Kconfig
+++ b/arch/xtensa/Kconfig
@@ -5,7 +5,6 @@
 	def_bool y
 	select ARCH_WANT_FRAME_POINTERS
 	select ARCH_WANT_IPC_PARSE_VERSION
-	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select BUILDTIME_EXTABLE_SORT
 	select CLONE_BACKWARDS
 	select COMMON_CLK
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 5f3429f..d00e7b6 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -33,7 +33,6 @@
 
 menuconfig GPIOLIB
 	bool "GPIO Support"
-	depends on ARCH_WANT_OPTIONAL_GPIOLIB || ARCH_REQUIRE_GPIOLIB
 	help
 	  This enables GPIO support through the generic GPIO library.
 	  You only need to enable this, if you also want to enable
@@ -49,7 +48,7 @@
 
 config OF_GPIO
 	def_bool y
-	depends on OF
+	depends on OF || COMPILE_TEST
 
 config GPIO_ACPI
 	def_bool y
@@ -122,6 +121,7 @@
 config GPIO_AMDPT
 	tristate "AMD Promontory GPIO support"
 	depends on ACPI
+	select GPIO_GENERIC
 	help
 	  driver for GPIO functionality on Promontory IOHub
 	  Require ACPI ASL code to enumerate as a platform device.
@@ -303,6 +303,7 @@
 		   FSL_SOC_BOOKE || PPC_86xx || ARCH_LAYERSCAPE || ARM || \
 		   COMPILE_TEST
 	select GPIO_GENERIC
+	select IRQ_DOMAIN
 	help
 	  Say Y here if you're going to use hardware that connects to the
 	  MPC512x/831x/834x/837x/8572/8610/QorIQ GPIOs.
@@ -399,6 +400,11 @@
 	select GENERIC_IRQ_CHIP
 	select OF_GPIO
 
+config GPIO_TEGRA
+	bool
+	default y
+	depends on ARCH_TEGRA || COMPILE_TEST
+
 config GPIO_TS4800
 	tristate "TS-4800 DIO blocks and compatibles"
 	depends on OF_GPIO
@@ -473,7 +479,7 @@
 
 config GPIO_XLP
 	tristate "Netlogic XLP GPIO support"
-	depends on CPU_XLP && OF_GPIO
+	depends on OF_GPIO && (CPU_XLP || ARCH_VULCAN || COMPILE_TEST)
 	select GPIOLIB_IRQCHIP
 	help
 	  This driver provides support for GPIO interface on Netlogic XLP MIPS64
@@ -510,6 +516,13 @@
 	help
 	  Say yes here to support the GPIO device on ZTE ZX SoCs.
 
+config GPIO_LOONGSON1
+	tristate "Loongson1 GPIO support"
+	depends on MACH_LOONGSON32
+	select GPIO_GENERIC
+	help
+	  Say Y or M here to support GPIO on Loongson1 SoCs.
+
 endmenu
 
 menu "Port-mapped I/O GPIO drivers"
@@ -557,7 +570,7 @@
 	  Say yes here to support GPIO functionality of IT87xx Super I/O chips.
 
 	  This driver is tested with ITE IT8728 and IT8732 Super I/O chips, and
-	  supports the IT8761E Super I/O chip as well.
+	  supports the IT8761E, IT8620E and IT8628E Super I/O chip as well.
 
 	  To compile this driver as a module, choose M here: the module will
 	  be called gpio_it87
@@ -1091,6 +1104,7 @@
 
 config GPIO_MCP23S08
 	tristate "Microchip MCP23xxx I/O expander"
+	select GPIOLIB_IRQCHIP
 	help
 	  SPI/I2C driver for Microchip MCP23S08/MCP23S17/MCP23008/MCP23017
 	  I/O expanders.
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 1e0b74f..991598e 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -12,6 +12,9 @@
 # Device drivers. Generally keep list sorted alphabetically
 obj-$(CONFIG_GPIO_GENERIC)	+= gpio-generic.o
 
+# directly supported by gpio-generic
+gpio-generic-$(CONFIG_GPIO_GENERIC)	+= gpio-mmio.o
+
 obj-$(CONFIG_GPIO_104_DIO_48E)	+= gpio-104-dio-48e.o
 obj-$(CONFIG_GPIO_104_IDIO_16)	+= gpio-104-idio-16.o
 obj-$(CONFIG_GPIO_104_IDI_48)	+= gpio-104-idi-48.o
@@ -95,7 +98,7 @@
 obj-$(CONFIG_GPIO_SYSCON)	+= gpio-syscon.o
 obj-$(CONFIG_GPIO_TB10X)	+= gpio-tb10x.o
 obj-$(CONFIG_GPIO_TC3589X)	+= gpio-tc3589x.o
-obj-$(CONFIG_ARCH_TEGRA)	+= gpio-tegra.o
+obj-$(CONFIG_GPIO_TEGRA)	+= gpio-tegra.o
 obj-$(CONFIG_GPIO_TIMBERDALE)	+= gpio-timberdale.o
 obj-$(CONFIG_GPIO_PALMAS)	+= gpio-palmas.o
 obj-$(CONFIG_GPIO_TPIC2810)	+= gpio-tpic2810.o
@@ -127,3 +130,4 @@
 obj-$(CONFIG_GPIO_ZEVIO)	+= gpio-zevio.o
 obj-$(CONFIG_GPIO_ZYNQ)		+= gpio-zynq.o
 obj-$(CONFIG_GPIO_ZX)		+= gpio-zx.o
+obj-$(CONFIG_GPIO_LOONGSON1)	+= gpio-loongson1.o
diff --git a/drivers/gpio/gpio-74x164.c b/drivers/gpio/gpio-74x164.c
index c81224f..80f9ddf 100644
--- a/drivers/gpio/gpio-74x164.c
+++ b/drivers/gpio/gpio-74x164.c
@@ -75,6 +75,29 @@
 	mutex_unlock(&chip->lock);
 }
 
+static void gen_74x164_set_multiple(struct gpio_chip *gc, unsigned long *mask,
+				    unsigned long *bits)
+{
+	struct gen_74x164_chip *chip = gpiochip_get_data(gc);
+	unsigned int i, idx, shift;
+	u8 bank, bankmask;
+
+	mutex_lock(&chip->lock);
+	for (i = 0, bank = chip->registers - 1; i < chip->registers;
+	     i++, bank--) {
+		idx = i / sizeof(*mask);
+		shift = i % sizeof(*mask) * BITS_PER_BYTE;
+		bankmask = mask[idx] >> shift;
+		if (!bankmask)
+			continue;
+
+		chip->buffer[bank] &= ~bankmask;
+		chip->buffer[bank] |= bankmask & (bits[idx] >> shift);
+	}
+	__gen_74x164_write_config(chip);
+	mutex_unlock(&chip->lock);
+}
+
 static int gen_74x164_direction_output(struct gpio_chip *gc,
 		unsigned offset, int val)
 {
@@ -114,6 +137,7 @@
 	chip->gpio_chip.direction_output = gen_74x164_direction_output;
 	chip->gpio_chip.get = gen_74x164_get_value;
 	chip->gpio_chip.set = gen_74x164_set_value;
+	chip->gpio_chip.set_multiple = gen_74x164_set_multiple;
 	chip->gpio_chip.base = -1;
 
 	chip->registers = nregs;
@@ -153,6 +177,7 @@
 
 static const struct of_device_id gen_74x164_dt_ids[] = {
 	{ .compatible = "fairchild,74hc595" },
+	{ .compatible = "nxp,74lvc594" },
 	{},
 };
 MODULE_DEVICE_TABLE(of, gen_74x164_dt_ids);
diff --git a/drivers/gpio/gpio-amdpt.c b/drivers/gpio/gpio-amdpt.c
index c248404..9b78dc8 100644
--- a/drivers/gpio/gpio-amdpt.c
+++ b/drivers/gpio/gpio-amdpt.c
@@ -28,7 +28,6 @@
 struct pt_gpio_chip {
 	struct gpio_chip         gc;
 	void __iomem             *reg_base;
-	spinlock_t               lock;
 };
 
 static int pt_gpio_request(struct gpio_chip *gc, unsigned offset)
@@ -39,19 +38,19 @@
 
 	dev_dbg(gc->parent, "pt_gpio_request offset=%x\n", offset);
 
-	spin_lock_irqsave(&pt_gpio->lock, flags);
+	spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	using_pins = readl(pt_gpio->reg_base + PT_SYNC_REG);
 	if (using_pins & BIT(offset)) {
 		dev_warn(gc->parent, "PT GPIO pin %x reconfigured\n",
 			 offset);
-		spin_unlock_irqrestore(&pt_gpio->lock, flags);
+		spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 		return -EINVAL;
 	}
 
 	writel(using_pins | BIT(offset), pt_gpio->reg_base + PT_SYNC_REG);
 
-	spin_unlock_irqrestore(&pt_gpio->lock, flags);
+	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	return 0;
 }
@@ -62,111 +61,17 @@
 	unsigned long flags;
 	u32 using_pins;
 
-	spin_lock_irqsave(&pt_gpio->lock, flags);
+	spin_lock_irqsave(&gc->bgpio_lock, flags);
 
 	using_pins = readl(pt_gpio->reg_base + PT_SYNC_REG);
 	using_pins &= ~BIT(offset);
 	writel(using_pins, pt_gpio->reg_base + PT_SYNC_REG);
 
-	spin_unlock_irqrestore(&pt_gpio->lock, flags);
+	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
 
 	dev_dbg(gc->parent, "pt_gpio_free offset=%x\n", offset);
 }
 
-static void pt_gpio_set_value(struct gpio_chip *gc, unsigned offset, int value)
-{
-	struct pt_gpio_chip *pt_gpio = gpiochip_get_data(gc);
-	unsigned long flags;
-	u32 data;
-
-	dev_dbg(gc->parent, "pt_gpio_set_value offset=%x, value=%x\n",
-		offset, value);
-
-	spin_lock_irqsave(&pt_gpio->lock, flags);
-
-	data = readl(pt_gpio->reg_base + PT_OUTPUTDATA_REG);
-	data &= ~BIT(offset);
-	if (value)
-		data |= BIT(offset);
-	writel(data, pt_gpio->reg_base + PT_OUTPUTDATA_REG);
-
-	spin_unlock_irqrestore(&pt_gpio->lock, flags);
-}
-
-static int pt_gpio_get_value(struct gpio_chip *gc, unsigned offset)
-{
-	struct pt_gpio_chip *pt_gpio = gpiochip_get_data(gc);
-	unsigned long flags;
-	u32 data;
-
-	spin_lock_irqsave(&pt_gpio->lock, flags);
-
-	data = readl(pt_gpio->reg_base + PT_DIRECTION_REG);
-
-	/* configure as output */
-	if (data & BIT(offset))
-		data = readl(pt_gpio->reg_base + PT_OUTPUTDATA_REG);
-	else	/* configure as input */
-		data = readl(pt_gpio->reg_base + PT_INPUTDATA_REG);
-
-	spin_unlock_irqrestore(&pt_gpio->lock, flags);
-
-	data >>= offset;
-	data &= 1;
-
-	dev_dbg(gc->parent, "pt_gpio_get_value offset=%x, value=%x\n",
-		offset, data);
-
-	return data;
-}
-
-static int pt_gpio_direction_input(struct gpio_chip *gc, unsigned offset)
-{
-	struct pt_gpio_chip *pt_gpio = gpiochip_get_data(gc);
-	unsigned long flags;
-	u32 data;
-
-	dev_dbg(gc->parent, "pt_gpio_dirction_input offset=%x\n", offset);
-
-	spin_lock_irqsave(&pt_gpio->lock, flags);
-
-	data = readl(pt_gpio->reg_base + PT_DIRECTION_REG);
-	data &= ~BIT(offset);
-	writel(data, pt_gpio->reg_base + PT_DIRECTION_REG);
-
-	spin_unlock_irqrestore(&pt_gpio->lock, flags);
-
-	return 0;
-}
-
-static int pt_gpio_direction_output(struct gpio_chip *gc,
-					unsigned offset, int value)
-{
-	struct pt_gpio_chip *pt_gpio = gpiochip_get_data(gc);
-	unsigned long flags;
-	u32 data;
-
-	dev_dbg(gc->parent, "pt_gpio_direction_output offset=%x, value=%x\n",
-		offset, value);
-
-	spin_lock_irqsave(&pt_gpio->lock, flags);
-
-	data = readl(pt_gpio->reg_base + PT_OUTPUTDATA_REG);
-	if (value)
-		data |= BIT(offset);
-	else
-		data &= ~BIT(offset);
-	writel(data, pt_gpio->reg_base + PT_OUTPUTDATA_REG);
-
-	data = readl(pt_gpio->reg_base + PT_DIRECTION_REG);
-	data |= BIT(offset);
-	writel(data, pt_gpio->reg_base + PT_DIRECTION_REG);
-
-	spin_unlock_irqrestore(&pt_gpio->lock, flags);
-
-	return 0;
-}
-
 static int pt_gpio_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -196,18 +101,19 @@
 		return PTR_ERR(pt_gpio->reg_base);
 	}
 
-	spin_lock_init(&pt_gpio->lock);
+	ret = bgpio_init(&pt_gpio->gc, dev, 4,
+			 pt_gpio->reg_base + PT_INPUTDATA_REG,
+			 pt_gpio->reg_base + PT_OUTPUTDATA_REG, NULL,
+			 pt_gpio->reg_base + PT_DIRECTION_REG, NULL,
+			 BGPIOF_READ_OUTPUT_REG_SET);
+	if (ret) {
+		dev_err(&pdev->dev, "bgpio_init failed\n");
+		return ret;
+	}
 
-	pt_gpio->gc.label            = pdev->name;
 	pt_gpio->gc.owner            = THIS_MODULE;
-	pt_gpio->gc.parent              = dev;
 	pt_gpio->gc.request          = pt_gpio_request;
 	pt_gpio->gc.free             = pt_gpio_free;
-	pt_gpio->gc.direction_input  = pt_gpio_direction_input;
-	pt_gpio->gc.direction_output = pt_gpio_direction_output;
-	pt_gpio->gc.get              = pt_gpio_get_value;
-	pt_gpio->gc.set              = pt_gpio_set_value;
-	pt_gpio->gc.base             = -1;
 	pt_gpio->gc.ngpio            = PT_TOTAL_GPIO;
 #if defined(CONFIG_OF_GPIO)
 	pt_gpio->gc.of_node          = pdev->dev.of_node;
@@ -239,6 +145,7 @@
 
 static const struct acpi_device_id pt_gpio_acpi_match[] = {
 	{ "AMDF030", 0 },
+	{ "AMDIF030", 0 },
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, pt_gpio_acpi_match);
diff --git a/drivers/gpio/gpio-bcm-kona.c b/drivers/gpio/gpio-bcm-kona.c
index 2fd38d5..9aabc48f 100644
--- a/drivers/gpio/gpio-bcm-kona.c
+++ b/drivers/gpio/gpio-bcm-kona.c
@@ -1,4 +1,7 @@
 /*
+ * Broadcom Kona GPIO Driver
+ *
+ * Author: Broadcom Corporation <bcm-kernel-feedback-list@broadcom.com>
  * Copyright (C) 2012-2014 Broadcom Corporation
  *
  * This program is free software; you can redistribute it and/or
@@ -17,7 +20,7 @@
 #include <linux/gpio.h>
 #include <linux/of_device.h>
 #include <linux/of_irq.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/irqdomain.h>
 #include <linux/irqchip/chained_irq.h>
 
@@ -502,8 +505,6 @@
 	{}
 };
 
-MODULE_DEVICE_TABLE(of, bcm_kona_gpio_of_match);
-
 /*
  * This lock class tells lockdep that GPIO irqs are in a different
  * category than their parents, so it won't report false recursion.
@@ -659,9 +660,4 @@
 	},
 	.probe = bcm_kona_gpio_probe,
 };
-
-module_platform_driver(bcm_kona_gpio_driver);
-
-MODULE_AUTHOR("Broadcom Corporation <bcm-kernel-feedback-list@broadcom.com>");
-MODULE_DESCRIPTION("Broadcom Kona GPIO Driver");
-MODULE_LICENSE("GPL v2");
+builtin_platform_driver(bcm_kona_gpio_driver);
diff --git a/drivers/gpio/gpio-brcmstb.c b/drivers/gpio/gpio-brcmstb.c
index 42d51c5..e648914 100644
--- a/drivers/gpio/gpio-brcmstb.c
+++ b/drivers/gpio/gpio-brcmstb.c
@@ -461,6 +461,7 @@
 		bank->id = num_banks;
 		if (bank_width <= 0 || bank_width > MAX_GPIO_PER_BANK) {
 			dev_err(dev, "Invalid bank width %d\n", bank_width);
+			err = -EINVAL;
 			goto fail;
 		} else {
 			bank->width = bank_width;
diff --git a/drivers/gpio/gpio-dwapb.c b/drivers/gpio/gpio-dwapb.c
index 597de1e..34779bb 100644
--- a/drivers/gpio/gpio-dwapb.c
+++ b/drivers/gpio/gpio-dwapb.c
@@ -7,6 +7,7 @@
  *
  * All enquiries to support@picochip.com
  */
+#include <linux/acpi.h>
 #include <linux/gpio/driver.h>
 /* FIXME: for gpio_get_value(), replace this with direct register read */
 #include <linux/gpio.h>
@@ -22,10 +23,13 @@
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
 #include <linux/platform_device.h>
+#include <linux/property.h>
 #include <linux/spinlock.h>
 #include <linux/platform_data/gpio-dwapb.h>
 #include <linux/slab.h>
 
+#include "gpiolib.h"
+
 #define GPIO_SWPORTA_DR		0x00
 #define GPIO_SWPORTA_DDR	0x04
 #define GPIO_SWPORTB_DR		0x0c
@@ -290,14 +294,14 @@
 				 struct dwapb_port_property *pp)
 {
 	struct gpio_chip *gc = &port->gc;
-	struct device_node *node = pp->node;
+	struct fwnode_handle  *fwnode = pp->fwnode;
 	struct irq_chip_generic	*irq_gc = NULL;
 	unsigned int hwirq, ngpio = gc->ngpio;
 	struct irq_chip_type *ct;
 	int err, i;
 
-	gpio->domain = irq_domain_add_linear(node, ngpio,
-					     &irq_generic_chip_ops, gpio);
+	gpio->domain = irq_domain_create_linear(fwnode, ngpio,
+						 &irq_generic_chip_ops, gpio);
 	if (!gpio->domain)
 		return;
 
@@ -409,13 +413,13 @@
 	err = bgpio_init(&port->gc, gpio->dev, 4, dat, set, NULL, dirout,
 			 NULL, false);
 	if (err) {
-		dev_err(gpio->dev, "failed to init gpio chip for %s\n",
-			pp->name);
+		dev_err(gpio->dev, "failed to init gpio chip for port%d\n",
+			port->idx);
 		return err;
 	}
 
 #ifdef CONFIG_OF_GPIO
-	port->gc.of_node = pp->node;
+	port->gc.of_node = to_of_node(pp->fwnode);
 #endif
 	port->gc.ngpio = pp->ngpio;
 	port->gc.base = pp->gpio_base;
@@ -429,11 +433,15 @@
 
 	err = gpiochip_add_data(&port->gc, port);
 	if (err)
-		dev_err(gpio->dev, "failed to register gpiochip for %s\n",
-			pp->name);
+		dev_err(gpio->dev, "failed to register gpiochip for port%d\n",
+			port->idx);
 	else
 		port->is_registered = true;
 
+	/* Add GPIO-signaled ACPI event support */
+	if (pp->irq)
+		acpi_gpiochip_request_interrupts(&port->gc);
+
 	return err;
 }
 
@@ -447,19 +455,15 @@
 }
 
 static struct dwapb_platform_data *
-dwapb_gpio_get_pdata_of(struct device *dev)
+dwapb_gpio_get_pdata(struct device *dev)
 {
-	struct device_node *node, *port_np;
+	struct fwnode_handle *fwnode;
 	struct dwapb_platform_data *pdata;
 	struct dwapb_port_property *pp;
 	int nports;
 	int i;
 
-	node = dev->of_node;
-	if (!IS_ENABLED(CONFIG_OF_GPIO) || !node)
-		return ERR_PTR(-ENODEV);
-
-	nports = of_get_child_count(node);
+	nports = device_get_child_node_count(dev);
 	if (nports == 0)
 		return ERR_PTR(-ENODEV);
 
@@ -474,21 +478,22 @@
 	pdata->nports = nports;
 
 	i = 0;
-	for_each_child_of_node(node, port_np) {
+	device_for_each_child_node(dev, fwnode)  {
 		pp = &pdata->properties[i++];
-		pp->node = port_np;
+		pp->fwnode = fwnode;
 
-		if (of_property_read_u32(port_np, "reg", &pp->idx) ||
+		if (fwnode_property_read_u32(fwnode, "reg", &pp->idx) ||
 		    pp->idx >= DWAPB_MAX_PORTS) {
-			dev_err(dev, "missing/invalid port index for %s\n",
-				port_np->full_name);
+			dev_err(dev,
+				"missing/invalid port index for port%d\n", i);
 			return ERR_PTR(-EINVAL);
 		}
 
-		if (of_property_read_u32(port_np, "snps,nr-gpios",
+		if (fwnode_property_read_u32(fwnode, "snps,nr-gpios",
 					 &pp->ngpio)) {
-			dev_info(dev, "failed to get number of gpios for %s\n",
-				 port_np->full_name);
+			dev_info(dev,
+				 "failed to get number of gpios for port%d\n",
+				 i);
 			pp->ngpio = 32;
 		}
 
@@ -496,18 +501,19 @@
 		 * Only port A can provide interrupts in all configurations of
 		 * the IP.
 		 */
-		if (pp->idx == 0 &&
-		    of_property_read_bool(port_np, "interrupt-controller")) {
-			pp->irq = irq_of_parse_and_map(port_np, 0);
-			if (!pp->irq) {
-				dev_warn(dev, "no irq for bank %s\n",
-					 port_np->full_name);
-			}
+		if (dev->of_node && pp->idx == 0 &&
+			fwnode_property_read_bool(fwnode,
+						  "interrupt-controller")) {
+			pp->irq = irq_of_parse_and_map(to_of_node(fwnode), 0);
+			if (!pp->irq)
+				dev_warn(dev, "no irq for port%d\n", pp->idx);
 		}
 
+		if (has_acpi_companion(dev) && pp->idx == 0)
+			pp->irq = platform_get_irq(to_platform_device(dev), 0);
+
 		pp->irq_shared	= false;
 		pp->gpio_base	= -1;
-		pp->name	= port_np->full_name;
 	}
 
 	return pdata;
@@ -523,7 +529,7 @@
 	struct dwapb_platform_data *pdata = dev_get_platdata(dev);
 
 	if (!pdata) {
-		pdata = dwapb_gpio_get_pdata_of(dev);
+		pdata = dwapb_gpio_get_pdata(dev);
 		if (IS_ERR(pdata))
 			return PTR_ERR(pdata);
 	}
@@ -580,6 +586,13 @@
 };
 MODULE_DEVICE_TABLE(of, dwapb_of_match);
 
+static const struct acpi_device_id dwapb_acpi_match[] = {
+	{"HISI0181", 0},
+	{"APMC0D07", 0},
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, dwapb_acpi_match);
+
 #ifdef CONFIG_PM_SLEEP
 static int dwapb_gpio_suspend(struct device *dev)
 {
@@ -674,6 +687,7 @@
 		.name	= "gpio-dwapb",
 		.pm	= &dwapb_gpio_pm_ops,
 		.of_match_table = of_match_ptr(dwapb_of_match),
+		.acpi_match_table = ACPI_PTR(dwapb_acpi_match),
 	},
 	.probe		= dwapb_gpio_probe,
 	.remove		= dwapb_gpio_remove,
diff --git a/drivers/gpio/gpio-f7188x.c b/drivers/gpio/gpio-f7188x.c
index daac2d4..05aa538 100644
--- a/drivers/gpio/gpio-f7188x.c
+++ b/drivers/gpio/gpio-f7188x.c
@@ -15,7 +15,8 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
+#include <linux/bitops.h>
 
 #define DRVNAME "gpio-f7188x"
 
@@ -129,6 +130,9 @@
 static int f7188x_gpio_direction_out(struct gpio_chip *chip,
 				     unsigned offset, int value);
 static void f7188x_gpio_set(struct gpio_chip *chip, unsigned offset, int value);
+static int f7188x_gpio_set_single_ended(struct gpio_chip *gc,
+					unsigned offset,
+					enum single_ended_mode mode);
 
 #define F7188X_GPIO_BANK(_base, _ngpio, _regbase)			\
 	{								\
@@ -139,6 +143,7 @@
 			.get              = f7188x_gpio_get,		\
 			.direction_output = f7188x_gpio_direction_out,	\
 			.set              = f7188x_gpio_set,		\
+			.set_single_ended = f7188x_gpio_set_single_ended, \
 			.base             = _base,			\
 			.ngpio            = _ngpio,			\
 			.can_sleep        = true,			\
@@ -217,7 +222,7 @@
 	superio_select(sio->addr, SIO_LD_GPIO);
 
 	dir = superio_inb(sio->addr, gpio_dir(bank->regbase));
-	dir &= ~(1 << offset);
+	dir &= ~BIT(offset);
 	superio_outb(sio->addr, gpio_dir(bank->regbase), dir);
 
 	superio_exit(sio->addr);
@@ -238,7 +243,7 @@
 	superio_select(sio->addr, SIO_LD_GPIO);
 
 	dir = superio_inb(sio->addr, gpio_dir(bank->regbase));
-	dir = !!(dir & (1 << offset));
+	dir = !!(dir & BIT(offset));
 	if (dir)
 		data = superio_inb(sio->addr, gpio_data_out(bank->regbase));
 	else
@@ -246,7 +251,7 @@
 
 	superio_exit(sio->addr);
 
-	return !!(data & 1 << offset);
+	return !!(data & BIT(offset));
 }
 
 static int f7188x_gpio_direction_out(struct gpio_chip *chip,
@@ -264,13 +269,13 @@
 
 	data_out = superio_inb(sio->addr, gpio_data_out(bank->regbase));
 	if (value)
-		data_out |= (1 << offset);
+		data_out |= BIT(offset);
 	else
-		data_out &= ~(1 << offset);
+		data_out &= ~BIT(offset);
 	superio_outb(sio->addr, gpio_data_out(bank->regbase), data_out);
 
 	dir = superio_inb(sio->addr, gpio_dir(bank->regbase));
-	dir |= (1 << offset);
+	dir |= BIT(offset);
 	superio_outb(sio->addr, gpio_dir(bank->regbase), dir);
 
 	superio_exit(sio->addr);
@@ -292,14 +297,43 @@
 
 	data_out = superio_inb(sio->addr, gpio_data_out(bank->regbase));
 	if (value)
-		data_out |= (1 << offset);
+		data_out |= BIT(offset);
 	else
-		data_out &= ~(1 << offset);
+		data_out &= ~BIT(offset);
 	superio_outb(sio->addr, gpio_data_out(bank->regbase), data_out);
 
 	superio_exit(sio->addr);
 }
 
+static int f7188x_gpio_set_single_ended(struct gpio_chip *chip,
+					unsigned offset,
+					enum single_ended_mode mode)
+{
+	int err;
+	struct f7188x_gpio_bank *bank = gpiochip_get_data(chip);
+	struct f7188x_sio *sio = bank->data->sio;
+	u8 data;
+
+	if (mode != LINE_MODE_OPEN_DRAIN &&
+	    mode != LINE_MODE_PUSH_PULL)
+		return -ENOTSUPP;
+
+	err = superio_enter(sio->addr);
+	if (err)
+		return err;
+	superio_select(sio->addr, SIO_LD_GPIO);
+
+	data = superio_inb(sio->addr, gpio_out_mode(bank->regbase));
+	if (mode == LINE_MODE_OPEN_DRAIN)
+		data &= ~BIT(offset);
+	else
+		data |= BIT(offset);
+	superio_outb(sio->addr, gpio_out_mode(bank->regbase), data);
+
+	superio_exit(sio->addr);
+	return 0;
+}
+
 /*
  * Platform device and driver.
  */
diff --git a/drivers/gpio/gpio-it87.c b/drivers/gpio/gpio-it87.c
index b219c82..63a962d 100644
--- a/drivers/gpio/gpio-it87.c
+++ b/drivers/gpio/gpio-it87.c
@@ -34,6 +34,8 @@
 
 /* Chip Id numbers */
 #define NO_DEV_ID	0xffff
+#define IT8620_ID	0x8620
+#define IT8628_ID	0x8628
 #define IT8728_ID	0x8728
 #define IT8732_ID	0x8732
 #define IT8761_ID	0x8761
@@ -302,6 +304,14 @@
 	it87_gpio->chip = it87_template_chip;
 
 	switch (chip_type) {
+	case IT8620_ID:
+	case IT8628_ID:
+		gpio_ba_reg = 0x62;
+		it87_gpio->io_size = 11;
+		it87_gpio->output_base = 0xc8;
+		it87_gpio->simple_size = 0;
+		it87_gpio->chip.ngpio = 64;
+		break;
 	case IT8728_ID:
 	case IT8732_ID:
 		gpio_ba_reg = 0x62;
diff --git a/drivers/gpio/gpio-loongson1.c b/drivers/gpio/gpio-loongson1.c
new file mode 100644
index 0000000..10c09bd
--- /dev/null
+++ b/drivers/gpio/gpio-loongson1.c
@@ -0,0 +1,102 @@
+/*
+ * GPIO Driver for Loongson 1 SoC
+ *
+ * Copyright (C) 2015-2016 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/gpio/driver.h>
+#include <linux/platform_device.h>
+
+/* Loongson 1 GPIO Register Definitions */
+#define GPIO_CFG		0x0
+#define GPIO_DIR		0x10
+#define GPIO_DATA		0x20
+#define GPIO_OUTPUT		0x30
+
+static void __iomem *gpio_reg_base;
+
+static int ls1x_gpio_request(struct gpio_chip *gc, unsigned int offset)
+{
+	unsigned long pinmask = gc->pin2mask(gc, offset);
+	unsigned long flags;
+
+	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	__raw_writel(__raw_readl(gpio_reg_base + GPIO_CFG) | pinmask,
+		     gpio_reg_base + GPIO_CFG);
+	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+
+	return 0;
+}
+
+static void ls1x_gpio_free(struct gpio_chip *gc, unsigned int offset)
+{
+	unsigned long pinmask = gc->pin2mask(gc, offset);
+	unsigned long flags;
+
+	spin_lock_irqsave(&gc->bgpio_lock, flags);
+	__raw_writel(__raw_readl(gpio_reg_base + GPIO_CFG) & ~pinmask,
+		     gpio_reg_base + GPIO_CFG);
+	spin_unlock_irqrestore(&gc->bgpio_lock, flags);
+}
+
+static int ls1x_gpio_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct gpio_chip *gc;
+	struct resource *res;
+	int ret;
+
+	gc = devm_kzalloc(dev, sizeof(*gc), GFP_KERNEL);
+	if (!gc)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "failed to get I/O memory\n");
+		return -EINVAL;
+	}
+
+	gpio_reg_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(gpio_reg_base))
+		return PTR_ERR(gpio_reg_base);
+
+	ret = bgpio_init(gc, dev, 4, gpio_reg_base + GPIO_DATA,
+			 gpio_reg_base + GPIO_OUTPUT, NULL,
+			 NULL, gpio_reg_base + GPIO_DIR, 0);
+	if (ret)
+		goto err;
+
+	gc->owner = THIS_MODULE;
+	gc->request = ls1x_gpio_request;
+	gc->free = ls1x_gpio_free;
+	gc->base = pdev->id * 32;
+
+	ret = devm_gpiochip_add_data(dev, gc, NULL);
+	if (ret)
+		goto err;
+
+	platform_set_drvdata(pdev, gc);
+	dev_info(dev, "Loongson1 GPIO driver registered\n");
+
+	return 0;
+err:
+	dev_err(dev, "failed to register GPIO device\n");
+	return ret;
+}
+
+static struct platform_driver ls1x_gpio_driver = {
+	.probe	= ls1x_gpio_probe,
+	.driver	= {
+		.name	= "ls1x-gpio",
+	},
+};
+
+module_platform_driver(ls1x_gpio_driver);
+
+MODULE_AUTHOR("Kelvin Cheung <keguang.zhang@gmail.com>");
+MODULE_DESCRIPTION("Loongson1 GPIO driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/gpio/gpio-mb86s7x.c b/drivers/gpio/gpio-mb86s7x.c
index 7fffc1d..d55af50 100644
--- a/drivers/gpio/gpio-mb86s7x.c
+++ b/drivers/gpio/gpio-mb86s7x.c
@@ -17,7 +17,6 @@
 #include <linux/io.h>
 #include <linux/init.h>
 #include <linux/clk.h>
-#include <linux/module.h>
 #include <linux/err.h>
 #include <linux/errno.h>
 #include <linux/ioport.h>
@@ -185,8 +184,6 @@
 	gchip->gc.parent = &pdev->dev;
 	gchip->gc.base = -1;
 
-	platform_set_drvdata(pdev, gchip);
-
 	ret = gpiochip_add_data(&gchip->gc, gchip);
 	if (ret) {
 		dev_err(&pdev->dev, "couldn't register gpio driver\n");
@@ -210,7 +207,6 @@
 	{ .compatible = "fujitsu,mb86s70-gpio" },
 	{ /* sentinel */ }
 };
-MODULE_DEVICE_TABLE(of, mb86s70_gpio_dt_ids);
 
 static struct platform_driver mb86s70_gpio_driver = {
 	.driver = {
@@ -225,8 +221,4 @@
 {
 	return platform_driver_register(&mb86s70_gpio_driver);
 }
-module_init(mb86s70_gpio_init);
-
-MODULE_DESCRIPTION("MB86S7x GPIO Driver");
-MODULE_ALIAS("platform:mb86s70-gpio");
-MODULE_LICENSE("GPL");
+device_initcall(mb86s70_gpio_init);
diff --git a/drivers/gpio/gpio-mc9s08dz60.c b/drivers/gpio/gpio-mc9s08dz60.c
index 14f252f..2fcad5b 100644
--- a/drivers/gpio/gpio-mc9s08dz60.c
+++ b/drivers/gpio/gpio-mc9s08dz60.c
@@ -15,7 +15,7 @@
  */
 
 #include <linux/kernel.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/slab.h>
 #include <linux/i2c.h>
 #include <linux/gpio.h>
@@ -111,8 +111,6 @@
 	{},
 };
 
-MODULE_DEVICE_TABLE(i2c, mc9s08dz60_id);
-
 static struct i2c_driver mc9s08dz60_i2c_driver = {
 	.driver = {
 		.name = "mc9s08dz60",
@@ -120,10 +118,4 @@
 	.probe = mc9s08dz60_probe,
 	.id_table = mc9s08dz60_id,
 };
-
-module_i2c_driver(mc9s08dz60_i2c_driver);
-
-MODULE_AUTHOR("Freescale Semiconductor, Inc. "
-		"Wu Guoxing <b39297@freescale.com>");
-MODULE_DESCRIPTION("mc9s08dz60 gpio function on mx35 3ds board");
-MODULE_LICENSE("GPL v2");
+builtin_i2c_driver(mc9s08dz60_i2c_driver);
diff --git a/drivers/gpio/gpio-mcp23s08.c b/drivers/gpio/gpio-mcp23s08.c
index 47e4869..ac22efc 100644
--- a/drivers/gpio/gpio-mcp23s08.c
+++ b/drivers/gpio/gpio-mcp23s08.c
@@ -77,7 +77,6 @@
 	/* lock protects the cached values */
 	struct mutex		lock;
 	struct mutex		irq_lock;
-	struct irq_domain	*irq_domain;
 
 	struct gpio_chip	chip;
 
@@ -96,11 +95,6 @@
 	struct mcp23s08		chip[];
 };
 
-/* This lock class tells lockdep that GPIO irqs are in a different
- * category than their parents, so it won't report false recursion.
- */
-static struct lock_class_key gpio_lock_class;
-
 /*----------------------------------------------------------------------*/
 
 #if IS_ENABLED(CONFIG_I2C)
@@ -368,8 +362,9 @@
 	for (i = 0; i < mcp->chip.ngpio; i++) {
 		if ((BIT(i) & mcp->cache[MCP_INTF]) &&
 		    ((BIT(i) & intcap & mcp->irq_rise) ||
-		     (mcp->irq_fall & ~intcap & BIT(i)))) {
-			child_irq = irq_find_mapping(mcp->irq_domain, i);
+		     (mcp->irq_fall & ~intcap & BIT(i)) ||
+		     (BIT(i) & mcp->cache[MCP_INTCON]))) {
+			child_irq = irq_find_mapping(mcp->chip.irqdomain, i);
 			handle_nested_irq(child_irq);
 		}
 	}
@@ -377,16 +372,10 @@
 	return IRQ_HANDLED;
 }
 
-static int mcp23s08_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
-{
-	struct mcp23s08 *mcp = gpiochip_get_data(chip);
-
-	return irq_find_mapping(mcp->irq_domain, offset);
-}
-
 static void mcp23s08_irq_mask(struct irq_data *data)
 {
-	struct mcp23s08 *mcp = irq_data_get_irq_chip_data(data);
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
+	struct mcp23s08 *mcp = gpiochip_get_data(gc);
 	unsigned int pos = data->hwirq;
 
 	mcp->cache[MCP_GPINTEN] &= ~BIT(pos);
@@ -394,7 +383,8 @@
 
 static void mcp23s08_irq_unmask(struct irq_data *data)
 {
-	struct mcp23s08 *mcp = irq_data_get_irq_chip_data(data);
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
+	struct mcp23s08 *mcp = gpiochip_get_data(gc);
 	unsigned int pos = data->hwirq;
 
 	mcp->cache[MCP_GPINTEN] |= BIT(pos);
@@ -402,7 +392,8 @@
 
 static int mcp23s08_irq_set_type(struct irq_data *data, unsigned int type)
 {
-	struct mcp23s08 *mcp = irq_data_get_irq_chip_data(data);
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
+	struct mcp23s08 *mcp = gpiochip_get_data(gc);
 	unsigned int pos = data->hwirq;
 	int status = 0;
 
@@ -418,6 +409,12 @@
 		mcp->cache[MCP_INTCON] &= ~BIT(pos);
 		mcp->irq_rise &= ~BIT(pos);
 		mcp->irq_fall |= BIT(pos);
+	} else if (type & IRQ_TYPE_LEVEL_HIGH) {
+		mcp->cache[MCP_INTCON] |= BIT(pos);
+		mcp->cache[MCP_DEFVAL] &= ~BIT(pos);
+	} else if (type & IRQ_TYPE_LEVEL_LOW) {
+		mcp->cache[MCP_INTCON] |= BIT(pos);
+		mcp->cache[MCP_DEFVAL] |= BIT(pos);
 	} else
 		return -EINVAL;
 
@@ -426,14 +423,16 @@
 
 static void mcp23s08_irq_bus_lock(struct irq_data *data)
 {
-	struct mcp23s08 *mcp = irq_data_get_irq_chip_data(data);
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
+	struct mcp23s08 *mcp = gpiochip_get_data(gc);
 
 	mutex_lock(&mcp->irq_lock);
 }
 
 static void mcp23s08_irq_bus_unlock(struct irq_data *data)
 {
-	struct mcp23s08 *mcp = irq_data_get_irq_chip_data(data);
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
+	struct mcp23s08 *mcp = gpiochip_get_data(gc);
 
 	mutex_lock(&mcp->lock);
 	mcp->ops->write(mcp, MCP_GPINTEN, mcp->cache[MCP_GPINTEN]);
@@ -443,27 +442,6 @@
 	mutex_unlock(&mcp->irq_lock);
 }
 
-static int mcp23s08_irq_reqres(struct irq_data *data)
-{
-	struct mcp23s08 *mcp = irq_data_get_irq_chip_data(data);
-
-	if (gpiochip_lock_as_irq(&mcp->chip, data->hwirq)) {
-		dev_err(mcp->chip.parent,
-			"unable to lock HW IRQ %lu for IRQ usage\n",
-			data->hwirq);
-		return -EINVAL;
-	}
-
-	return 0;
-}
-
-static void mcp23s08_irq_relres(struct irq_data *data)
-{
-	struct mcp23s08 *mcp = irq_data_get_irq_chip_data(data);
-
-	gpiochip_unlock_as_irq(&mcp->chip, data->hwirq);
-}
-
 static struct irq_chip mcp23s08_irq_chip = {
 	.name = "gpio-mcp23xxx",
 	.irq_mask = mcp23s08_irq_mask,
@@ -471,24 +449,16 @@
 	.irq_set_type = mcp23s08_irq_set_type,
 	.irq_bus_lock = mcp23s08_irq_bus_lock,
 	.irq_bus_sync_unlock = mcp23s08_irq_bus_unlock,
-	.irq_request_resources = mcp23s08_irq_reqres,
-	.irq_release_resources = mcp23s08_irq_relres,
 };
 
 static int mcp23s08_irq_setup(struct mcp23s08 *mcp)
 {
 	struct gpio_chip *chip = &mcp->chip;
-	int err, irq, j;
+	int err;
 	unsigned long irqflags = IRQF_ONESHOT | IRQF_SHARED;
 
 	mutex_init(&mcp->irq_lock);
 
-	mcp->irq_domain = irq_domain_add_linear(chip->parent->of_node,
-						chip->ngpio,
-						&irq_domain_simple_ops, mcp);
-	if (!mcp->irq_domain)
-		return -ENODEV;
-
 	if (mcp->irq_active_high)
 		irqflags |= IRQF_TRIGGER_HIGH;
 	else
@@ -503,32 +473,25 @@
 		return err;
 	}
 
-	chip->to_irq = mcp23s08_gpio_to_irq;
-
-	for (j = 0; j < mcp->chip.ngpio; j++) {
-		irq = irq_create_mapping(mcp->irq_domain, j);
-		irq_set_lockdep_class(irq, &gpio_lock_class);
-		irq_set_chip_data(irq, mcp);
-		irq_set_chip(irq, &mcp23s08_irq_chip);
-		irq_set_nested_thread(irq, true);
-		irq_set_noprobe(irq);
+	err =  gpiochip_irqchip_add(chip,
+				    &mcp23s08_irq_chip,
+				    0,
+				    handle_simple_irq,
+				    IRQ_TYPE_NONE);
+	if (err) {
+		dev_err(chip->parent,
+			"could not connect irqchip to gpiochip: %d\n", err);
+		return err;
 	}
+
+	gpiochip_set_chained_irqchip(chip,
+				     &mcp23s08_irq_chip,
+				     mcp->irq,
+				     NULL);
+
 	return 0;
 }
 
-static void mcp23s08_irq_teardown(struct mcp23s08 *mcp)
-{
-	unsigned int irq, i;
-
-	for (i = 0; i < mcp->chip.ngpio; i++) {
-		irq = irq_find_mapping(mcp->irq_domain, i);
-		if (irq > 0)
-			irq_dispose_mapping(irq);
-	}
-
-	irq_domain_remove(mcp->irq_domain);
-}
-
 /*----------------------------------------------------------------------*/
 
 #ifdef CONFIG_DEBUG_FS
@@ -721,7 +684,6 @@
 	if (mcp->irq && mcp->irq_controller) {
 		status = mcp23s08_irq_setup(mcp);
 		if (status) {
-			mcp23s08_irq_teardown(mcp);
 			goto fail;
 		}
 	}
@@ -847,9 +809,6 @@
 {
 	struct mcp23s08 *mcp = i2c_get_clientdata(client);
 
-	if (client->irq && mcp->irq_controller)
-		mcp23s08_irq_teardown(mcp);
-
 	gpiochip_remove(&mcp->chip);
 	kfree(mcp);
 
@@ -1017,8 +976,6 @@
 		if (!data->mcp[addr])
 			continue;
 
-		if (spi->irq && data->mcp[addr]->irq_controller)
-			mcp23s08_irq_teardown(data->mcp[addr]);
 		gpiochip_remove(&data->mcp[addr]->chip);
 	}
 
diff --git a/drivers/gpio/gpio-menz127.c b/drivers/gpio/gpio-menz127.c
index c5c9599..cc103af 100644
--- a/drivers/gpio/gpio-menz127.c
+++ b/drivers/gpio/gpio-menz127.c
@@ -35,7 +35,6 @@
 struct men_z127_gpio {
 	struct gpio_chip gc;
 	void __iomem *reg_base;
-	struct mcb_device *mdev;
 	struct resource *mem;
 };
 
@@ -43,7 +42,7 @@
 			     unsigned debounce)
 {
 	struct men_z127_gpio *priv = gpiochip_get_data(gc);
-	struct device *dev = &priv->mdev->dev;
+	struct device *dev = gc->parent;
 	unsigned int rnd;
 	u32 db_en, db_cnt;
 
@@ -88,21 +87,25 @@
 	return 0;
 }
 
-static int men_z127_request(struct gpio_chip *gc, unsigned gpio_pin)
+static int men_z127_set_single_ended(struct gpio_chip *gc,
+				     unsigned offset,
+				     enum single_ended_mode mode)
 {
 	struct men_z127_gpio *priv = gpiochip_get_data(gc);
 	u32 od_en;
 
-	if (gpio_pin >= gc->ngpio)
-		return -EINVAL;
+	if (mode != LINE_MODE_OPEN_DRAIN &&
+	    mode != LINE_MODE_PUSH_PULL)
+		return -ENOTSUPP;
 
 	spin_lock(&gc->bgpio_lock);
 	od_en = readl(priv->reg_base + MEN_Z127_ODER);
 
-	if (gpiochip_line_is_open_drain(gc, gpio_pin))
-		od_en |= BIT(gpio_pin);
+	if (mode == LINE_MODE_OPEN_DRAIN)
+		od_en |= BIT(offset);
 	else
-		od_en &= ~BIT(gpio_pin);
+		/* Implicitly LINE_MODE_PUSH_PULL */
+		od_en &= ~BIT(offset);
 
 	writel(od_en, priv->reg_base + MEN_Z127_ODER);
 	spin_unlock(&gc->bgpio_lock);
@@ -135,7 +138,6 @@
 		goto err_release;
 	}
 
-	men_z127_gpio->mdev = mdev;
 	mcb_set_drvdata(mdev, men_z127_gpio);
 
 	ret = bgpio_init(&men_z127_gpio->gc, &mdev->dev, 4,
@@ -148,7 +150,7 @@
 		goto err_unmap;
 
 	men_z127_gpio->gc.set_debounce = men_z127_debounce;
-	men_z127_gpio->gc.request = men_z127_request;
+	men_z127_gpio->gc.set_single_ended = men_z127_set_single_ended;
 
 	ret = gpiochip_add_data(&men_z127_gpio->gc, men_z127_gpio);
 	if (ret) {
diff --git a/drivers/gpio/gpio-generic.c b/drivers/gpio/gpio-mmio.c
similarity index 99%
rename from drivers/gpio/gpio-generic.c
rename to drivers/gpio/gpio-mmio.c
index 54cddfa..6c1cb3b 100644
--- a/drivers/gpio/gpio-generic.c
+++ b/drivers/gpio/gpio-mmio.c
@@ -549,7 +549,7 @@
 }
 EXPORT_SYMBOL_GPL(bgpio_init);
 
-#ifdef CONFIG_GPIO_GENERIC_PLATFORM
+#if IS_ENABLED(CONFIG_GPIO_GENERIC_PLATFORM)
 
 static void __iomem *bgpio_map(struct platform_device *pdev,
 			       const char *name,
diff --git a/drivers/gpio/gpio-moxart.c b/drivers/gpio/gpio-moxart.c
index f02d0b4..d58d3890 100644
--- a/drivers/gpio/gpio-moxart.c
+++ b/drivers/gpio/gpio-moxart.c
@@ -15,7 +15,6 @@
 #include <linux/irq.h>
 #include <linux/io.h>
 #include <linux/platform_device.h>
-#include <linux/module.h>
 #include <linux/of_address.h>
 #include <linux/of_gpio.h>
 #include <linux/pinctrl/consumer.h>
@@ -82,8 +81,4 @@
 	},
 	.probe	= moxart_gpio_probe,
 };
-module_platform_driver(moxart_gpio_driver);
-
-MODULE_DESCRIPTION("MOXART GPIO chip driver");
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Jonas Jensen <jonas.jensen@gmail.com>");
+builtin_platform_driver(moxart_gpio_driver);
diff --git a/drivers/gpio/gpio-mvebu.c b/drivers/gpio/gpio-mvebu.c
index 11c6582..cd5dc27 100644
--- a/drivers/gpio/gpio-mvebu.c
+++ b/drivers/gpio/gpio-mvebu.c
@@ -34,7 +34,7 @@
  */
 
 #include <linux/err.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/gpio.h>
 #include <linux/irq.h>
 #include <linux/slab.h>
@@ -557,7 +557,6 @@
 		/* sentinel */
 	},
 };
-MODULE_DEVICE_TABLE(of, mvebu_gpio_of_match);
 
 static int mvebu_gpio_suspend(struct platform_device *pdev, pm_message_t state)
 {
@@ -838,4 +837,4 @@
 	.suspend        = mvebu_gpio_suspend,
 	.resume         = mvebu_gpio_resume,
 };
-module_platform_driver(mvebu_gpio_driver);
+builtin_platform_driver(mvebu_gpio_driver);
diff --git a/drivers/gpio/gpio-octeon.c b/drivers/gpio/gpio-octeon.c
index 47aead1..96a8a8c 100644
--- a/drivers/gpio/gpio-octeon.c
+++ b/drivers/gpio/gpio-octeon.c
@@ -83,6 +83,7 @@
 	struct octeon_gpio *gpio;
 	struct gpio_chip *chip;
 	struct resource *res_mem;
+	void __iomem *reg_base;
 	int err = 0;
 
 	gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
@@ -91,21 +92,11 @@
 	chip = &gpio->chip;
 
 	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (res_mem == NULL) {
-		dev_err(&pdev->dev, "found no memory resource\n");
-		err = -ENXIO;
-		goto out;
-	}
-	if (!devm_request_mem_region(&pdev->dev, res_mem->start,
-					resource_size(res_mem),
-				     res_mem->name)) {
-		dev_err(&pdev->dev, "request_mem_region failed\n");
-		err = -ENXIO;
-		goto out;
-	}
-	gpio->register_base = (u64)devm_ioremap(&pdev->dev, res_mem->start,
-						resource_size(res_mem));
+	reg_base = devm_ioremap_resource(&pdev->dev, res_mem);
+	if (IS_ERR(reg_base))
+		return PTR_ERR(reg_base);
 
+	gpio->register_base = (u64)reg_base;
 	pdev->dev.platform_data = chip;
 	chip->label = "octeon-gpio";
 	chip->parent = &pdev->dev;
@@ -119,14 +110,13 @@
 	chip->set = octeon_gpio_set;
 	err = devm_gpiochip_add_data(&pdev->dev, chip, gpio);
 	if (err)
-		goto out;
+		return err;
 
 	dev_info(&pdev->dev, "OCTEON GPIO driver probed.\n");
-out:
-	return err;
+	return 0;
 }
 
-static struct of_device_id octeon_gpio_match[] = {
+static const struct of_device_id octeon_gpio_match[] = {
 	{
 		.compatible = "cavium,octeon-3860-gpio",
 	},
diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index 551dfa9..b98ede7 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -611,51 +611,12 @@
 		omap_disable_gpio_irqbank(bank, BIT(offset));
 }
 
-/*
- * Note that ENAWAKEUP needs to be enabled in GPIO_SYSCONFIG register.
- * 1510 does not seem to have a wake-up register. If JTAG is connected
- * to the target, system will wake up always on GPIO events. While
- * system is running all registered GPIO interrupts need to have wake-up
- * enabled. When system is suspended, only selected GPIO interrupts need
- * to have wake-up enabled.
- */
-static int omap_set_gpio_wakeup(struct gpio_bank *bank, unsigned offset,
-				int enable)
-{
-	u32 gpio_bit = BIT(offset);
-	unsigned long flags;
-
-	if (bank->non_wakeup_gpios & gpio_bit) {
-		dev_err(bank->chip.parent,
-			"Unable to modify wakeup on non-wakeup GPIO%d\n",
-			offset);
-		return -EINVAL;
-	}
-
-	raw_spin_lock_irqsave(&bank->lock, flags);
-	if (enable)
-		bank->context.wake_en |= gpio_bit;
-	else
-		bank->context.wake_en &= ~gpio_bit;
-
-	writel_relaxed(bank->context.wake_en, bank->base + bank->regs->wkup_en);
-	raw_spin_unlock_irqrestore(&bank->lock, flags);
-
-	return 0;
-}
-
 /* Use disable_irq_wake() and enable_irq_wake() functions from drivers */
 static int omap_gpio_wake_enable(struct irq_data *d, unsigned int enable)
 {
 	struct gpio_bank *bank = omap_irq_data_get_bank(d);
-	unsigned offset = d->hwirq;
-	int ret;
 
-	ret = omap_set_gpio_wakeup(bank, offset, enable);
-	if (!ret)
-		ret = irq_set_irq_wake(bank->irq, enable);
-
-	return ret;
+	return irq_set_irq_wake(bank->irq, enable);
 }
 
 static int omap_gpio_request(struct gpio_chip *chip, unsigned offset)
@@ -1187,6 +1148,7 @@
 	irqc->irq_bus_lock = omap_gpio_irq_bus_lock,
 	irqc->irq_bus_sync_unlock = gpio_irq_bus_sync_unlock,
 	irqc->name = dev_name(&pdev->dev);
+	irqc->flags = IRQCHIP_MASK_ON_SUSPEND;
 
 	bank->irq = platform_get_irq(pdev, 0);
 	if (bank->irq <= 0) {
diff --git a/drivers/gpio/gpio-palmas.c b/drivers/gpio/gpio-palmas.c
index 6f27b3d..e248707 100644
--- a/drivers/gpio/gpio-palmas.c
+++ b/drivers/gpio/gpio-palmas.c
@@ -20,7 +20,7 @@
 
 #include <linux/gpio.h>
 #include <linux/kernel.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/mfd/palmas.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
@@ -218,14 +218,3 @@
 	return platform_driver_register(&palmas_gpio_driver);
 }
 subsys_initcall(palmas_gpio_init);
-
-static void __exit palmas_gpio_exit(void)
-{
-	platform_driver_unregister(&palmas_gpio_driver);
-}
-module_exit(palmas_gpio_exit);
-
-MODULE_ALIAS("platform:palmas-gpio");
-MODULE_AUTHOR("Laxman Dewangan <ldewangan@nvidia.com>");
-MODULE_DESCRIPTION("GPIO driver for TI Palmas series PMICs");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/gpio/gpio-pca953x.c b/drivers/gpio/gpio-pca953x.c
index e66084c..5e3be32 100644
--- a/drivers/gpio/gpio-pca953x.c
+++ b/drivers/gpio/gpio-pca953x.c
@@ -38,8 +38,13 @@
 #define PCA957X_MSK		6
 #define PCA957X_INTS		7
 
+#define PCAL953X_IN_LATCH	34
+#define PCAL953X_INT_MASK	37
+#define PCAL953X_INT_STAT	38
+
 #define PCA_GPIO_MASK		0x00FF
 #define PCA_INT			0x0100
+#define PCA_PCAL			0x0200
 #define PCA953X_TYPE		0x1000
 #define PCA957X_TYPE		0x2000
 #define PCA_TYPE_MASK		0xF000
@@ -77,7 +82,7 @@
 MODULE_DEVICE_TABLE(i2c, pca953x_id);
 
 static const struct acpi_device_id pca953x_acpi_ids[] = {
-	{ "INT3491", 16 | PCA953X_TYPE | PCA_INT, },
+	{ "INT3491", 16 | PCA953X_TYPE | PCA_INT | PCA_PCAL, },
 	{ }
 };
 MODULE_DEVICE_TABLE(acpi, pca953x_acpi_ids);
@@ -437,6 +442,18 @@
 	struct pca953x_chip *chip = gpiochip_get_data(gc);
 	u8 new_irqs;
 	int level, i;
+	u8 invert_irq_mask[MAX_BANK];
+
+	if (chip->driver_data & PCA_PCAL) {
+		/* Enable latch on interrupt-enabled inputs */
+		pca953x_write_regs(chip, PCAL953X_IN_LATCH, chip->irq_mask);
+
+		for (i = 0; i < NBANK(chip); i++)
+			invert_irq_mask[i] = ~chip->irq_mask[i];
+
+		/* Unmask enabled interrupts */
+		pca953x_write_regs(chip, PCAL953X_INT_MASK, invert_irq_mask);
+	}
 
 	/* Look for any newly setup interrupt */
 	for (i = 0; i < NBANK(chip); i++) {
@@ -498,6 +515,29 @@
 	u8 trigger[MAX_BANK];
 	int ret, i, offset = 0;
 
+	if (chip->driver_data & PCA_PCAL) {
+		/* Read the current interrupt status from the device */
+		ret = pca953x_read_regs(chip, PCAL953X_INT_STAT, trigger);
+		if (ret)
+			return false;
+
+		/* Check latched inputs and clear interrupt status */
+		ret = pca953x_read_regs(chip, PCA953X_INPUT, cur_stat);
+		if (ret)
+			return false;
+
+		for (i = 0; i < NBANK(chip); i++) {
+			/* Apply filter for rising/falling edge selection */
+			pending[i] = (~cur_stat[i] & chip->irq_trig_fall[i]) |
+				(cur_stat[i] & chip->irq_trig_raise[i]);
+			pending[i] &= trigger[i];
+			if (pending[i])
+				pending_seen = true;
+		}
+
+		return pending_seen;
+	}
+
 	switch (chip->chip_type) {
 	case PCA953X_TYPE:
 		offset = PCA953X_INPUT;
diff --git a/drivers/gpio/gpio-pl061.c b/drivers/gpio/gpio-pl061.c
index 5cb3821..6e3c143 100644
--- a/drivers/gpio/gpio-pl061.c
+++ b/drivers/gpio/gpio-pl061.c
@@ -1,6 +1,8 @@
 /*
  * Copyright (C) 2008, 2009 Provigent Ltd.
  *
+ * Author: Baruch Siach <baruch@tkos.co.il>
+ *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
@@ -11,7 +13,7 @@
  */
 #include <linux/spinlock.h>
 #include <linux/errno.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/io.h>
 #include <linux/ioport.h>
 #include <linux/interrupt.h>
@@ -59,15 +61,19 @@
 #endif
 };
 
+static int pl061_get_direction(struct gpio_chip *gc, unsigned offset)
+{
+	struct pl061_gpio *chip = gpiochip_get_data(gc);
+
+	return !(readb(chip->base + GPIODIR) & BIT(offset));
+}
+
 static int pl061_direction_input(struct gpio_chip *gc, unsigned offset)
 {
 	struct pl061_gpio *chip = gpiochip_get_data(gc);
 	unsigned long flags;
 	unsigned char gpiodir;
 
-	if (offset >= gc->ngpio)
-		return -EINVAL;
-
 	spin_lock_irqsave(&chip->lock, flags);
 	gpiodir = readb(chip->base + GPIODIR);
 	gpiodir &= ~(BIT(offset));
@@ -84,9 +90,6 @@
 	unsigned long flags;
 	unsigned char gpiodir;
 
-	if (offset >= gc->ngpio)
-		return -EINVAL;
-
 	spin_lock_irqsave(&chip->lock, flags);
 	writeb(!!value << offset, chip->base + (BIT(offset + 2)));
 	gpiodir = readb(chip->base + GPIODIR);
@@ -319,6 +322,7 @@
 		chip->gc.free = gpiochip_generic_free;
 	}
 
+	chip->gc.get_direction = pl061_get_direction;
 	chip->gc.direction_input = pl061_direction_input;
 	chip->gc.direction_output = pl061_direction_output;
 	chip->gc.get = pl061_get_value;
@@ -429,8 +433,6 @@
 	{ 0, 0 },
 };
 
-MODULE_DEVICE_TABLE(amba, pl061_ids);
-
 static struct amba_driver pl061_gpio_driver = {
 	.drv = {
 		.name	= "pl061_gpio",
@@ -446,8 +448,4 @@
 {
 	return amba_driver_register(&pl061_gpio_driver);
 }
-module_init(pl061_gpio_init);
-
-MODULE_AUTHOR("Baruch Siach <baruch@tkos.co.il>");
-MODULE_DESCRIPTION("PL061 GPIO driver");
-MODULE_LICENSE("GPL");
+device_initcall(pl061_gpio_init);
diff --git a/drivers/gpio/gpio-rc5t583.c b/drivers/gpio/gpio-rc5t583.c
index 1d6100f..3b4dc1a 100644
--- a/drivers/gpio/gpio-rc5t583.c
+++ b/drivers/gpio/gpio-rc5t583.c
@@ -23,7 +23,6 @@
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/slab.h>
-#include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/device.h>
 #include <linux/gpio.h>
@@ -152,14 +151,3 @@
 	return platform_driver_register(&rc5t583_gpio_driver);
 }
 subsys_initcall(rc5t583_gpio_init);
-
-static void __exit rc5t583_gpio_exit(void)
-{
-	platform_driver_unregister(&rc5t583_gpio_driver);
-}
-module_exit(rc5t583_gpio_exit);
-
-MODULE_AUTHOR("Laxman Dewangan <ldewangan@nvidia.com>");
-MODULE_DESCRIPTION("GPIO interface for RC5T583");
-MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform:rc5t583-gpio");
diff --git a/drivers/gpio/gpio-rcar.c b/drivers/gpio/gpio-rcar.c
index 4d9a315..681c93f 100644
--- a/drivers/gpio/gpio-rcar.c
+++ b/drivers/gpio/gpio-rcar.c
@@ -284,6 +284,25 @@
 	spin_unlock_irqrestore(&p->lock, flags);
 }
 
+static void gpio_rcar_set_multiple(struct gpio_chip *chip, unsigned long *mask,
+				   unsigned long *bits)
+{
+	struct gpio_rcar_priv *p = gpiochip_get_data(chip);
+	unsigned long flags;
+	u32 val, bankmask;
+
+	bankmask = mask[0] & GENMASK(chip->ngpio - 1, 0);
+	if (!bankmask)
+		return;
+
+	spin_lock_irqsave(&p->lock, flags);
+	val = gpio_rcar_read(p, OUTDT);
+	val &= ~bankmask;
+	val |= (bankmask & bits[0]);
+	gpio_rcar_write(p, OUTDT, val);
+	spin_unlock_irqrestore(&p->lock, flags);
+}
+
 static int gpio_rcar_direction_output(struct gpio_chip *chip, unsigned offset,
 				      int value)
 {
@@ -425,6 +444,7 @@
 	gpio_chip->get = gpio_rcar_get;
 	gpio_chip->direction_output = gpio_rcar_direction_output;
 	gpio_chip->set = gpio_rcar_set;
+	gpio_chip->set_multiple = gpio_rcar_set_multiple;
 	gpio_chip->label = name;
 	gpio_chip->parent = dev;
 	gpio_chip->owner = THIS_MODULE;
diff --git a/drivers/gpio/gpio-sodaville.c b/drivers/gpio/gpio-sodaville.c
index e3cb677..7da9e6c 100644
--- a/drivers/gpio/gpio-sodaville.c
+++ b/drivers/gpio/gpio-sodaville.c
@@ -3,6 +3,8 @@
  *
  *  Copyright (c) 2010, 2011 Intel Corporation
  *
+ *  Author: Hans J. Koch <hjk@linutronix.de>
+ *
  *  This program is free software; you can redistribute it and/or modify
  *  it under the terms of the GNU General Public License 2 as published
  *  by the Free Software Foundation.
@@ -15,7 +17,6 @@
 #include <linux/irq.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
-#include <linux/module.h>
 #include <linux/pci.h>
 #include <linux/platform_device.h>
 #include <linux/of_irq.h>
@@ -257,34 +258,17 @@
 	return ret;
 }
 
-static void sdv_gpio_remove(struct pci_dev *pdev)
-{
-	struct sdv_gpio_chip_data *sd = pci_get_drvdata(pdev);
-
-	free_irq(pdev->irq, sd);
-	irq_free_descs(sd->irq_base, SDV_NUM_PUB_GPIOS);
-
-	gpiochip_remove(&sd->chip);
-	pci_release_region(pdev, GPIO_BAR);
-	iounmap(sd->gpio_pub_base);
-	pci_disable_device(pdev);
-	kfree(sd);
-}
-
 static const struct pci_device_id sdv_gpio_pci_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_SDV_GPIO) },
 	{ 0, },
 };
 
 static struct pci_driver sdv_gpio_driver = {
+	.driver = {
+		.suppress_bind_attrs = true,
+	},
 	.name = DRV_NAME,
 	.id_table = sdv_gpio_pci_ids,
 	.probe = sdv_gpio_probe,
-	.remove = sdv_gpio_remove,
 };
-
-module_pci_driver(sdv_gpio_driver);
-
-MODULE_AUTHOR("Hans J. Koch <hjk@linutronix.de>");
-MODULE_DESCRIPTION("GPIO interface for Intel Sodaville SoCs");
-MODULE_LICENSE("GPL v2");
+builtin_pci_driver(sdv_gpio_driver);
diff --git a/drivers/gpio/gpio-sta2x11.c b/drivers/gpio/gpio-sta2x11.c
index 0d5b8c5..853ca23 100644
--- a/drivers/gpio/gpio-sta2x11.c
+++ b/drivers/gpio/gpio-sta2x11.c
@@ -20,7 +20,7 @@
  *
  */
 
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/slab.h>
 #include <linux/gpio.h>
@@ -432,8 +432,4 @@
 	},
 	.probe = gsta_probe,
 };
-
-module_platform_driver(sta2x11_gpio_platform_driver);
-
-MODULE_LICENSE("GPL v2");
-MODULE_DESCRIPTION("sta2x11_gpio GPIO driver");
+builtin_platform_driver(sta2x11_gpio_platform_driver);
diff --git a/drivers/gpio/gpio-stmpe.c b/drivers/gpio/gpio-stmpe.c
index 5197edf..6f7af28 100644
--- a/drivers/gpio/gpio-stmpe.c
+++ b/drivers/gpio/gpio-stmpe.c
@@ -5,7 +5,6 @@
  * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
  */
 
-#include <linux/module.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
@@ -413,23 +412,13 @@
 	return ret;
 }
 
-static int stmpe_gpio_remove(struct platform_device *pdev)
-{
-	struct stmpe_gpio *stmpe_gpio = platform_get_drvdata(pdev);
-	struct stmpe *stmpe = stmpe_gpio->stmpe;
-
-	gpiochip_remove(&stmpe_gpio->chip);
-	stmpe_disable(stmpe, STMPE_BLOCK_GPIO);
-	kfree(stmpe_gpio);
-
-	return 0;
-}
-
 static struct platform_driver stmpe_gpio_driver = {
-	.driver.name	= "stmpe-gpio",
-	.driver.owner	= THIS_MODULE,
+	.driver = {
+		.suppress_bind_attrs	= true,
+		.name			= "stmpe-gpio",
+		.owner			= THIS_MODULE,
+	},
 	.probe		= stmpe_gpio_probe,
-	.remove		= stmpe_gpio_remove,
 };
 
 static int __init stmpe_gpio_init(void)
@@ -437,13 +426,3 @@
 	return platform_driver_register(&stmpe_gpio_driver);
 }
 subsys_initcall(stmpe_gpio_init);
-
-static void __exit stmpe_gpio_exit(void)
-{
-	platform_driver_unregister(&stmpe_gpio_driver);
-}
-module_exit(stmpe_gpio_exit);
-
-MODULE_LICENSE("GPL v2");
-MODULE_DESCRIPTION("STMPExxxx GPIO driver");
-MODULE_AUTHOR("Rabin Vincent <rabin.vincent@stericsson.com>");
diff --git a/drivers/gpio/gpio-sx150x.c b/drivers/gpio/gpio-sx150x.c
index d387eb5..a177ebd 100644
--- a/drivers/gpio/gpio-sx150x.c
+++ b/drivers/gpio/gpio-sx150x.c
@@ -1,5 +1,9 @@
 /* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
  *
+ * Driver for Semtech SX150X I2C GPIO Expanders
+ *
+ * Author: Gregory Bean <gbean@codeaurora.org>
+ *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 and
  * only version 2 as published by the Free Software Foundation.
@@ -19,10 +23,8 @@
 #include <linux/init.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
-#include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/slab.h>
-#include <linux/i2c/sx150x.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
@@ -82,6 +84,57 @@
 	} pri;
 };
 
+/**
+ * struct sx150x_platform_data - config data for SX150x driver
+ * @gpio_base: The index number of the first GPIO assigned to this
+ *             GPIO expander.  The expander will create a block of
+ *             consecutively numbered gpios beginning at the given base,
+ *             with the size of the block depending on the model of the
+ *             expander chip.
+ * @oscio_is_gpo: If set to true, the driver will configure OSCIO as a GPO
+ *                instead of as an oscillator, increasing the size of the
+ *                GP(I)O pool created by this expander by one.  The
+ *                output-only GPO pin will be added at the end of the block.
+ * @io_pullup_ena: A bit-mask which enables or disables the pull-up resistor
+ *                 for each IO line in the expander.  Setting the bit at
+ *                 position n will enable the pull-up for the IO at
+ *                 the corresponding offset.  For chips with fewer than
+ *                 16 IO pins, high-end bits are ignored.
+ * @io_pulldn_ena: A bit-mask which enables-or disables the pull-down
+ *                 resistor for each IO line in the expander. Setting the
+ *                 bit at position n will enable the pull-down for the IO at
+ *                 the corresponding offset.  For chips with fewer than
+ *                 16 IO pins, high-end bits are ignored.
+ * @io_polarity: A bit-mask which enables polarity inversion for each IO line
+ *               in the expander.  Setting the bit at position n inverts
+ *               the polarity of that IO line, while clearing it results
+ *               in normal polarity. For chips with fewer than 16 IO pins,
+ *               high-end bits are ignored.
+ * @irq_summary: The 'summary IRQ' line to which the GPIO expander's INT line
+ *               is connected, via which it reports interrupt events
+ *               across all GPIO lines.  This must be a real,
+ *               pre-existing IRQ line.
+ *               Setting this value < 0 disables the irq_chip functionality
+ *               of the driver.
+ * @irq_base: The first 'virtual IRQ' line at which our block of GPIO-based
+ *            IRQ lines will appear.  Similarly to gpio_base, the expander
+ *            will create a block of irqs beginning at this number.
+ *            This value is ignored if irq_summary is < 0.
+ * @reset_during_probe: If set to true, the driver will trigger a full
+ *                      reset of the chip at the beginning of the probe
+ *                      in order to place it in a known state.
+ */
+struct sx150x_platform_data {
+	unsigned gpio_base;
+	bool     oscio_is_gpo;
+	u16      io_pullup_ena;
+	u16      io_pulldn_ena;
+	u16      io_polarity;
+	int      irq_summary;
+	unsigned irq_base;
+	bool     reset_during_probe;
+};
+
 struct sx150x_chip {
 	struct gpio_chip                 gpio_chip;
 	struct i2c_client               *client;
@@ -354,6 +407,32 @@
 	mutex_unlock(&chip->lock);
 }
 
+static int sx150x_gpio_set_single_ended(struct gpio_chip *gc,
+					unsigned offset,
+                                        enum single_ended_mode mode)
+{
+	struct sx150x_chip *chip = gpiochip_get_data(gc);
+
+	/* On the SX160X 789 we can set open drain */
+	if (chip->dev_cfg->model != SX150X_789)
+		return -ENOTSUPP;
+
+	if (mode == LINE_MODE_PUSH_PULL)
+		return sx150x_write_cfg(chip,
+					offset,
+					1,
+					chip->dev_cfg->pri.x789.reg_drain,
+					0);
+
+	if (mode == LINE_MODE_OPEN_DRAIN)
+		return sx150x_write_cfg(chip,
+					offset,
+					1,
+					chip->dev_cfg->pri.x789.reg_drain,
+					1);
+	return -ENOTSUPP;
+}
+
 static int sx150x_gpio_direction_input(struct gpio_chip *gc, unsigned offset)
 {
 	struct sx150x_chip *chip = gpiochip_get_data(gc);
@@ -508,6 +587,7 @@
 	chip->gpio_chip.direction_output = sx150x_gpio_direction_output;
 	chip->gpio_chip.get              = sx150x_gpio_get;
 	chip->gpio_chip.set              = sx150x_gpio_set;
+	chip->gpio_chip.set_single_ended = sx150x_gpio_set_single_ended;
 	chip->gpio_chip.base             = pdata->gpio_base;
 	chip->gpio_chip.can_sleep        = true;
 	chip->gpio_chip.ngpio            = chip->dev_cfg->ngpios;
@@ -597,12 +677,6 @@
 
 	if (chip->dev_cfg->model == SX150X_789) {
 		err = sx150x_init_io(chip,
-				chip->dev_cfg->pri.x789.reg_drain,
-				pdata->io_open_drain_ena);
-		if (err < 0)
-			return err;
-
-		err = sx150x_init_io(chip,
 				chip->dev_cfg->pri.x789.reg_polarity,
 				pdata->io_polarity);
 		if (err < 0)
@@ -718,13 +792,3 @@
 	return i2c_add_driver(&sx150x_driver);
 }
 subsys_initcall(sx150x_init);
-
-static void __exit sx150x_exit(void)
-{
-	return i2c_del_driver(&sx150x_driver);
-}
-module_exit(sx150x_exit);
-
-MODULE_AUTHOR("Gregory Bean <gbean@codeaurora.org>");
-MODULE_DESCRIPTION("Driver for Semtech SX150X I2C GPIO Expanders");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/gpio/gpio-tc3589x.c b/drivers/gpio/gpio-tc3589x.c
index 4f566e6..2e35ed3 100644
--- a/drivers/gpio/gpio-tc3589x.c
+++ b/drivers/gpio/gpio-tc3589x.c
@@ -6,14 +6,14 @@
  * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
  */
 
-#include <linux/module.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/of.h>
 #include <linux/interrupt.h>
 #include <linux/mfd/tc3589x.h>
+#include <linux/bitops.h>
 
 /*
  * These registers are modified under the irq bus lock and cached to avoid
@@ -39,7 +39,7 @@
 	struct tc3589x_gpio *tc3589x_gpio = gpiochip_get_data(chip);
 	struct tc3589x *tc3589x = tc3589x_gpio->tc3589x;
 	u8 reg = TC3589x_GPIODATA0 + (offset / 8) * 2;
-	u8 mask = 1 << (offset % 8);
+	u8 mask = BIT(offset % 8);
 	int ret;
 
 	ret = tc3589x_reg_read(tc3589x, reg);
@@ -55,7 +55,7 @@
 	struct tc3589x *tc3589x = tc3589x_gpio->tc3589x;
 	u8 reg = TC3589x_GPIODATA0 + (offset / 8) * 2;
 	unsigned pos = offset % 8;
-	u8 data[] = {!!val << pos, 1 << pos};
+	u8 data[] = {val ? BIT(pos) : 0, BIT(pos)};
 
 	tc3589x_block_write(tc3589x, reg, ARRAY_SIZE(data), data);
 }
@@ -70,7 +70,7 @@
 
 	tc3589x_gpio_set(chip, offset, val);
 
-	return tc3589x_set_bits(tc3589x, reg, 1 << pos, 1 << pos);
+	return tc3589x_set_bits(tc3589x, reg, BIT(pos), BIT(pos));
 }
 
 static int tc3589x_gpio_direction_input(struct gpio_chip *chip,
@@ -81,7 +81,47 @@
 	u8 reg = TC3589x_GPIODIR0 + offset / 8;
 	unsigned pos = offset % 8;
 
-	return tc3589x_set_bits(tc3589x, reg, 1 << pos, 0);
+	return tc3589x_set_bits(tc3589x, reg, BIT(pos), 0);
+}
+
+static int tc3589x_gpio_single_ended(struct gpio_chip *chip,
+				     unsigned offset,
+				     enum single_ended_mode mode)
+{
+	struct tc3589x_gpio *tc3589x_gpio = gpiochip_get_data(chip);
+	struct tc3589x *tc3589x = tc3589x_gpio->tc3589x;
+	/*
+	 * These registers are alterated at each second address
+	 * ODM bit 0 = drive to GND or Hi-Z (open drain)
+	 * ODM bit 1 = drive to VDD or Hi-Z (open source)
+	 */
+	u8 odmreg = TC3589x_GPIOODM0 + (offset / 8) * 2;
+	u8 odereg = TC3589x_GPIOODE0 + (offset / 8) * 2;
+	unsigned pos = offset % 8;
+	int ret;
+
+	switch(mode) {
+	case LINE_MODE_OPEN_DRAIN:
+		/* Set open drain mode */
+		ret = tc3589x_set_bits(tc3589x, odmreg, BIT(pos), 0);
+		if (ret)
+			return ret;
+		/* Enable open drain/source mode */
+		return tc3589x_set_bits(tc3589x, odereg, BIT(pos), BIT(pos));
+	case LINE_MODE_OPEN_SOURCE:
+		/* Set open source mode */
+		ret = tc3589x_set_bits(tc3589x, odmreg, BIT(pos), BIT(pos));
+		if (ret)
+			return ret;
+		/* Enable open drain/source mode */
+		return tc3589x_set_bits(tc3589x, odereg, BIT(pos), BIT(pos));
+	case LINE_MODE_PUSH_PULL:
+		/* Disable open drain/source mode */
+		return tc3589x_set_bits(tc3589x, odereg, BIT(pos), 0);
+	default:
+		break;
+	}
+	return -ENOTSUPP;
 }
 
 static struct gpio_chip template_chip = {
@@ -91,6 +131,7 @@
 	.get			= tc3589x_gpio_get,
 	.direction_output	= tc3589x_gpio_direction_output,
 	.set			= tc3589x_gpio_set,
+	.set_single_ended	= tc3589x_gpio_single_ended,
 	.can_sleep		= true,
 };
 
@@ -100,7 +141,7 @@
 	struct tc3589x_gpio *tc3589x_gpio = gpiochip_get_data(gc);
 	int offset = d->hwirq;
 	int regoffset = offset / 8;
-	int mask = 1 << (offset % 8);
+	int mask = BIT(offset % 8);
 
 	if (type == IRQ_TYPE_EDGE_BOTH) {
 		tc3589x_gpio->regs[REG_IBE][regoffset] |= mask;
@@ -165,7 +206,7 @@
 	struct tc3589x_gpio *tc3589x_gpio = gpiochip_get_data(gc);
 	int offset = d->hwirq;
 	int regoffset = offset / 8;
-	int mask = 1 << (offset % 8);
+	int mask = BIT(offset % 8);
 
 	tc3589x_gpio->regs[REG_IE][regoffset] &= ~mask;
 }
@@ -176,7 +217,7 @@
 	struct tc3589x_gpio *tc3589x_gpio = gpiochip_get_data(gc);
 	int offset = d->hwirq;
 	int regoffset = offset / 8;
-	int mask = 1 << (offset % 8);
+	int mask = BIT(offset % 8);
 
 	tc3589x_gpio->regs[REG_IE][regoffset] |= mask;
 }
@@ -311,13 +352,3 @@
 	return platform_driver_register(&tc3589x_gpio_driver);
 }
 subsys_initcall(tc3589x_gpio_init);
-
-static void __exit tc3589x_gpio_exit(void)
-{
-	platform_driver_unregister(&tc3589x_gpio_driver);
-}
-module_exit(tc3589x_gpio_exit);
-
-MODULE_LICENSE("GPL v2");
-MODULE_DESCRIPTION("TC3589x GPIO driver");
-MODULE_AUTHOR("Hanumath Prasad, Rabin Vincent");
diff --git a/drivers/gpio/gpio-tegra.c b/drivers/gpio/gpio-tegra.c
index 790bb11..ec891a27 100644
--- a/drivers/gpio/gpio-tegra.c
+++ b/drivers/gpio/gpio-tegra.c
@@ -35,24 +35,27 @@
 #define GPIO_PORT(x)		(((x) >> 3) & 0x3)
 #define GPIO_BIT(x)		((x) & 0x7)
 
-#define GPIO_REG(x)		(GPIO_BANK(x) * tegra_gpio_bank_stride + \
+#define GPIO_REG(tgi, x)	(GPIO_BANK(x) * tgi->soc->bank_stride + \
 					GPIO_PORT(x) * 4)
 
-#define GPIO_CNF(x)		(GPIO_REG(x) + 0x00)
-#define GPIO_OE(x)		(GPIO_REG(x) + 0x10)
-#define GPIO_OUT(x)		(GPIO_REG(x) + 0X20)
-#define GPIO_IN(x)		(GPIO_REG(x) + 0x30)
-#define GPIO_INT_STA(x)		(GPIO_REG(x) + 0x40)
-#define GPIO_INT_ENB(x)		(GPIO_REG(x) + 0x50)
-#define GPIO_INT_LVL(x)		(GPIO_REG(x) + 0x60)
-#define GPIO_INT_CLR(x)		(GPIO_REG(x) + 0x70)
+#define GPIO_CNF(t, x)		(GPIO_REG(t, x) + 0x00)
+#define GPIO_OE(t, x)		(GPIO_REG(t, x) + 0x10)
+#define GPIO_OUT(t, x)		(GPIO_REG(t, x) + 0X20)
+#define GPIO_IN(t, x)		(GPIO_REG(t, x) + 0x30)
+#define GPIO_INT_STA(t, x)	(GPIO_REG(t, x) + 0x40)
+#define GPIO_INT_ENB(t, x)	(GPIO_REG(t, x) + 0x50)
+#define GPIO_INT_LVL(t, x)	(GPIO_REG(t, x) + 0x60)
+#define GPIO_INT_CLR(t, x)	(GPIO_REG(t, x) + 0x70)
+#define GPIO_DBC_CNT(t, x)	(GPIO_REG(t, x) + 0xF0)
 
-#define GPIO_MSK_CNF(x)		(GPIO_REG(x) + tegra_gpio_upper_offset + 0x00)
-#define GPIO_MSK_OE(x)		(GPIO_REG(x) + tegra_gpio_upper_offset + 0x10)
-#define GPIO_MSK_OUT(x)		(GPIO_REG(x) + tegra_gpio_upper_offset + 0X20)
-#define GPIO_MSK_INT_STA(x)	(GPIO_REG(x) + tegra_gpio_upper_offset + 0x40)
-#define GPIO_MSK_INT_ENB(x)	(GPIO_REG(x) + tegra_gpio_upper_offset + 0x50)
-#define GPIO_MSK_INT_LVL(x)	(GPIO_REG(x) + tegra_gpio_upper_offset + 0x60)
+
+#define GPIO_MSK_CNF(t, x)	(GPIO_REG(t, x) + t->soc->upper_offset + 0x00)
+#define GPIO_MSK_OE(t, x)	(GPIO_REG(t, x) + t->soc->upper_offset + 0x10)
+#define GPIO_MSK_OUT(t, x)	(GPIO_REG(t, x) + t->soc->upper_offset + 0X20)
+#define GPIO_MSK_DBC_EN(t, x)	(GPIO_REG(t, x) + t->soc->upper_offset + 0x30)
+#define GPIO_MSK_INT_STA(t, x)	(GPIO_REG(t, x) + t->soc->upper_offset + 0x40)
+#define GPIO_MSK_INT_ENB(t, x)	(GPIO_REG(t, x) + t->soc->upper_offset + 0x50)
+#define GPIO_MSK_INT_LVL(t, x)	(GPIO_REG(t, x) + t->soc->upper_offset + 0x60)
 
 #define GPIO_INT_LVL_MASK		0x010101
 #define GPIO_INT_LVL_EDGE_RISING	0x000101
@@ -61,10 +64,13 @@
 #define GPIO_INT_LVL_LEVEL_HIGH		0x000001
 #define GPIO_INT_LVL_LEVEL_LOW		0x000000
 
+struct tegra_gpio_info;
+
 struct tegra_gpio_bank {
 	int bank;
 	int irq;
 	spinlock_t lvl_lock[4];
+	spinlock_t dbc_lock[4];	/* Lock for updating debounce count register */
 #ifdef CONFIG_PM_SLEEP
 	u32 cnf[4];
 	u32 out[4];
@@ -72,25 +78,39 @@
 	u32 int_enb[4];
 	u32 int_lvl[4];
 	u32 wake_enb[4];
+	u32 dbc_enb[4];
 #endif
+	u32 dbc_cnt[4];
+	struct tegra_gpio_info *tgi;
 };
 
-static struct device *dev;
-static struct irq_domain *irq_domain;
-static void __iomem *regs;
-static u32 tegra_gpio_bank_count;
-static u32 tegra_gpio_bank_stride;
-static u32 tegra_gpio_upper_offset;
-static struct tegra_gpio_bank *tegra_gpio_banks;
+struct tegra_gpio_soc_config {
+	bool debounce_supported;
+	u32 bank_stride;
+	u32 upper_offset;
+};
 
-static inline void tegra_gpio_writel(u32 val, u32 reg)
+struct tegra_gpio_info {
+	struct device				*dev;
+	void __iomem				*regs;
+	struct irq_domain			*irq_domain;
+	struct tegra_gpio_bank			*bank_info;
+	const struct tegra_gpio_soc_config	*soc;
+	struct gpio_chip			gc;
+	struct irq_chip				ic;
+	struct lock_class_key			lock_class;
+	u32					bank_count;
+};
+
+static inline void tegra_gpio_writel(struct tegra_gpio_info *tgi,
+				     u32 val, u32 reg)
 {
-	__raw_writel(val, regs + reg);
+	__raw_writel(val, tgi->regs + reg);
 }
 
-static inline u32 tegra_gpio_readl(u32 reg)
+static inline u32 tegra_gpio_readl(struct tegra_gpio_info *tgi, u32 reg)
 {
-	return __raw_readl(regs + reg);
+	return __raw_readl(tgi->regs + reg);
 }
 
 static int tegra_gpio_compose(int bank, int port, int bit)
@@ -98,24 +118,25 @@
 	return (bank << 5) | ((port & 0x3) << 3) | (bit & 0x7);
 }
 
-static void tegra_gpio_mask_write(u32 reg, int gpio, int value)
+static void tegra_gpio_mask_write(struct tegra_gpio_info *tgi, u32 reg,
+				  int gpio, int value)
 {
 	u32 val;
 
 	val = 0x100 << GPIO_BIT(gpio);
 	if (value)
 		val |= 1 << GPIO_BIT(gpio);
-	tegra_gpio_writel(val, reg);
+	tegra_gpio_writel(tgi, val, reg);
 }
 
-static void tegra_gpio_enable(int gpio)
+static void tegra_gpio_enable(struct tegra_gpio_info *tgi, int gpio)
 {
-	tegra_gpio_mask_write(GPIO_MSK_CNF(gpio), gpio, 1);
+	tegra_gpio_mask_write(tgi, GPIO_MSK_CNF(tgi, gpio), gpio, 1);
 }
 
-static void tegra_gpio_disable(int gpio)
+static void tegra_gpio_disable(struct tegra_gpio_info *tgi, int gpio)
 {
-	tegra_gpio_mask_write(GPIO_MSK_CNF(gpio), gpio, 0);
+	tegra_gpio_mask_write(tgi, GPIO_MSK_CNF(tgi, gpio), gpio, 0);
 }
 
 static int tegra_gpio_request(struct gpio_chip *chip, unsigned offset)
@@ -125,83 +146,138 @@
 
 static void tegra_gpio_free(struct gpio_chip *chip, unsigned offset)
 {
+	struct tegra_gpio_info *tgi = gpiochip_get_data(chip);
+
 	pinctrl_free_gpio(offset);
-	tegra_gpio_disable(offset);
+	tegra_gpio_disable(tgi, offset);
 }
 
 static void tegra_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 {
-	tegra_gpio_mask_write(GPIO_MSK_OUT(offset), offset, value);
+	struct tegra_gpio_info *tgi = gpiochip_get_data(chip);
+
+	tegra_gpio_mask_write(tgi, GPIO_MSK_OUT(tgi, offset), offset, value);
 }
 
 static int tegra_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
-	/* If gpio is in output mode then read from the out value */
-	if ((tegra_gpio_readl(GPIO_OE(offset)) >> GPIO_BIT(offset)) & 1)
-		return (tegra_gpio_readl(GPIO_OUT(offset)) >>
-				GPIO_BIT(offset)) & 0x1;
+	struct tegra_gpio_info *tgi = gpiochip_get_data(chip);
+	int bval = BIT(GPIO_BIT(offset));
 
-	return (tegra_gpio_readl(GPIO_IN(offset)) >> GPIO_BIT(offset)) & 0x1;
+	/* If gpio is in output mode then read from the out value */
+	if (tegra_gpio_readl(tgi, GPIO_OE(tgi, offset)) & bval)
+		return !!(tegra_gpio_readl(tgi, GPIO_OUT(tgi, offset)) & bval);
+
+	return !!(tegra_gpio_readl(tgi, GPIO_IN(tgi, offset)) & bval);
 }
 
 static int tegra_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
 {
-	tegra_gpio_mask_write(GPIO_MSK_OE(offset), offset, 0);
-	tegra_gpio_enable(offset);
+	struct tegra_gpio_info *tgi = gpiochip_get_data(chip);
+
+	tegra_gpio_mask_write(tgi, GPIO_MSK_OE(tgi, offset), offset, 0);
+	tegra_gpio_enable(tgi, offset);
 	return 0;
 }
 
 static int tegra_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
 					int value)
 {
+	struct tegra_gpio_info *tgi = gpiochip_get_data(chip);
+
 	tegra_gpio_set(chip, offset, value);
-	tegra_gpio_mask_write(GPIO_MSK_OE(offset), offset, 1);
-	tegra_gpio_enable(offset);
+	tegra_gpio_mask_write(tgi, GPIO_MSK_OE(tgi, offset), offset, 1);
+	tegra_gpio_enable(tgi, offset);
+	return 0;
+}
+
+static int tegra_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
+{
+	struct tegra_gpio_info *tgi = gpiochip_get_data(chip);
+	u32 pin_mask = BIT(GPIO_BIT(offset));
+	u32 cnf, oe;
+
+	cnf = tegra_gpio_readl(tgi, GPIO_CNF(tgi, offset));
+	if (!(cnf & pin_mask))
+		return -EINVAL;
+
+	oe = tegra_gpio_readl(tgi, GPIO_OE(tgi, offset));
+
+	return (oe & pin_mask) ? GPIOF_DIR_OUT : GPIOF_DIR_IN;
+}
+
+static int tegra_gpio_set_debounce(struct gpio_chip *chip, unsigned int offset,
+				   unsigned int debounce)
+{
+	struct tegra_gpio_info *tgi = gpiochip_get_data(chip);
+	struct tegra_gpio_bank *bank = &tgi->bank_info[GPIO_BANK(offset)];
+	unsigned int debounce_ms = DIV_ROUND_UP(debounce, 1000);
+	unsigned long flags;
+	int port;
+
+	if (!debounce_ms) {
+		tegra_gpio_mask_write(tgi, GPIO_MSK_DBC_EN(tgi, offset),
+				      offset, 0);
+		return 0;
+	}
+
+	debounce_ms = min(debounce_ms, 255U);
+	port = GPIO_PORT(offset);
+
+	/* There is only one debounce count register per port and hence
+	 * set the maximum of current and requested debounce time.
+	 */
+	spin_lock_irqsave(&bank->dbc_lock[port], flags);
+	if (bank->dbc_cnt[port] < debounce_ms) {
+		tegra_gpio_writel(tgi, debounce_ms, GPIO_DBC_CNT(tgi, offset));
+		bank->dbc_cnt[port] = debounce_ms;
+	}
+	spin_unlock_irqrestore(&bank->dbc_lock[port], flags);
+
+	tegra_gpio_mask_write(tgi, GPIO_MSK_DBC_EN(tgi, offset), offset, 1);
+
 	return 0;
 }
 
 static int tegra_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
 {
-	return irq_find_mapping(irq_domain, offset);
-}
+	struct tegra_gpio_info *tgi = gpiochip_get_data(chip);
 
-static struct gpio_chip tegra_gpio_chip = {
-	.label			= "tegra-gpio",
-	.request		= tegra_gpio_request,
-	.free			= tegra_gpio_free,
-	.direction_input	= tegra_gpio_direction_input,
-	.get			= tegra_gpio_get,
-	.direction_output	= tegra_gpio_direction_output,
-	.set			= tegra_gpio_set,
-	.to_irq			= tegra_gpio_to_irq,
-	.base			= 0,
-};
+	return irq_find_mapping(tgi->irq_domain, offset);
+}
 
 static void tegra_gpio_irq_ack(struct irq_data *d)
 {
+	struct tegra_gpio_bank *bank = irq_data_get_irq_chip_data(d);
+	struct tegra_gpio_info *tgi = bank->tgi;
 	int gpio = d->hwirq;
 
-	tegra_gpio_writel(1 << GPIO_BIT(gpio), GPIO_INT_CLR(gpio));
+	tegra_gpio_writel(tgi, 1 << GPIO_BIT(gpio), GPIO_INT_CLR(tgi, gpio));
 }
 
 static void tegra_gpio_irq_mask(struct irq_data *d)
 {
+	struct tegra_gpio_bank *bank = irq_data_get_irq_chip_data(d);
+	struct tegra_gpio_info *tgi = bank->tgi;
 	int gpio = d->hwirq;
 
-	tegra_gpio_mask_write(GPIO_MSK_INT_ENB(gpio), gpio, 0);
+	tegra_gpio_mask_write(tgi, GPIO_MSK_INT_ENB(tgi, gpio), gpio, 0);
 }
 
 static void tegra_gpio_irq_unmask(struct irq_data *d)
 {
+	struct tegra_gpio_bank *bank = irq_data_get_irq_chip_data(d);
+	struct tegra_gpio_info *tgi = bank->tgi;
 	int gpio = d->hwirq;
 
-	tegra_gpio_mask_write(GPIO_MSK_INT_ENB(gpio), gpio, 1);
+	tegra_gpio_mask_write(tgi, GPIO_MSK_INT_ENB(tgi, gpio), gpio, 1);
 }
 
 static int tegra_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 {
 	int gpio = d->hwirq;
 	struct tegra_gpio_bank *bank = irq_data_get_irq_chip_data(d);
+	struct tegra_gpio_info *tgi = bank->tgi;
 	int port = GPIO_PORT(gpio);
 	int lvl_type;
 	int val;
@@ -233,23 +309,24 @@
 		return -EINVAL;
 	}
 
-	ret = gpiochip_lock_as_irq(&tegra_gpio_chip, gpio);
+	ret = gpiochip_lock_as_irq(&tgi->gc, gpio);
 	if (ret) {
-		dev_err(dev, "unable to lock Tegra GPIO %d as IRQ\n", gpio);
+		dev_err(tgi->dev,
+			"unable to lock Tegra GPIO %d as IRQ\n", gpio);
 		return ret;
 	}
 
 	spin_lock_irqsave(&bank->lvl_lock[port], flags);
 
-	val = tegra_gpio_readl(GPIO_INT_LVL(gpio));
+	val = tegra_gpio_readl(tgi, GPIO_INT_LVL(tgi, gpio));
 	val &= ~(GPIO_INT_LVL_MASK << GPIO_BIT(gpio));
 	val |= lvl_type << GPIO_BIT(gpio);
-	tegra_gpio_writel(val, GPIO_INT_LVL(gpio));
+	tegra_gpio_writel(tgi, val, GPIO_INT_LVL(tgi, gpio));
 
 	spin_unlock_irqrestore(&bank->lvl_lock[port], flags);
 
-	tegra_gpio_mask_write(GPIO_MSK_OE(gpio), gpio, 0);
-	tegra_gpio_enable(gpio);
+	tegra_gpio_mask_write(tgi, GPIO_MSK_OE(tgi, gpio), gpio, 0);
+	tegra_gpio_enable(tgi, gpio);
 
 	if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH))
 		irq_set_handler_locked(d, handle_level_irq);
@@ -261,9 +338,11 @@
 
 static void tegra_gpio_irq_shutdown(struct irq_data *d)
 {
+	struct tegra_gpio_bank *bank = irq_data_get_irq_chip_data(d);
+	struct tegra_gpio_info *tgi = bank->tgi;
 	int gpio = d->hwirq;
 
-	gpiochip_unlock_as_irq(&tegra_gpio_chip, gpio);
+	gpiochip_unlock_as_irq(&tgi->gc, gpio);
 }
 
 static void tegra_gpio_irq_handler(struct irq_desc *desc)
@@ -271,19 +350,24 @@
 	int port;
 	int pin;
 	int unmasked = 0;
+	int gpio;
+	u32 lvl;
+	unsigned long sta;
 	struct irq_chip *chip = irq_desc_get_chip(desc);
 	struct tegra_gpio_bank *bank = irq_desc_get_handler_data(desc);
+	struct tegra_gpio_info *tgi = bank->tgi;
 
 	chained_irq_enter(chip, desc);
 
 	for (port = 0; port < 4; port++) {
-		int gpio = tegra_gpio_compose(bank->bank, port, 0);
-		unsigned long sta = tegra_gpio_readl(GPIO_INT_STA(gpio)) &
-			tegra_gpio_readl(GPIO_INT_ENB(gpio));
-		u32 lvl = tegra_gpio_readl(GPIO_INT_LVL(gpio));
+		gpio = tegra_gpio_compose(bank->bank, port, 0);
+		sta = tegra_gpio_readl(tgi, GPIO_INT_STA(tgi, gpio)) &
+			tegra_gpio_readl(tgi, GPIO_INT_ENB(tgi, gpio));
+		lvl = tegra_gpio_readl(tgi, GPIO_INT_LVL(tgi, gpio));
 
 		for_each_set_bit(pin, &sta, 8) {
-			tegra_gpio_writel(1 << pin, GPIO_INT_CLR(gpio));
+			tegra_gpio_writel(tgi, 1 << pin,
+					  GPIO_INT_CLR(tgi, gpio));
 
 			/* if gpio is edge triggered, clear condition
 			 * before executing the handler so that we don't
@@ -306,22 +390,37 @@
 #ifdef CONFIG_PM_SLEEP
 static int tegra_gpio_resume(struct device *dev)
 {
+	struct platform_device *pdev = to_platform_device(dev);
+	struct tegra_gpio_info *tgi = platform_get_drvdata(pdev);
 	unsigned long flags;
 	int b;
 	int p;
 
 	local_irq_save(flags);
 
-	for (b = 0; b < tegra_gpio_bank_count; b++) {
-		struct tegra_gpio_bank *bank = &tegra_gpio_banks[b];
+	for (b = 0; b < tgi->bank_count; b++) {
+		struct tegra_gpio_bank *bank = &tgi->bank_info[b];
 
 		for (p = 0; p < ARRAY_SIZE(bank->oe); p++) {
 			unsigned int gpio = (b<<5) | (p<<3);
-			tegra_gpio_writel(bank->cnf[p], GPIO_CNF(gpio));
-			tegra_gpio_writel(bank->out[p], GPIO_OUT(gpio));
-			tegra_gpio_writel(bank->oe[p], GPIO_OE(gpio));
-			tegra_gpio_writel(bank->int_lvl[p], GPIO_INT_LVL(gpio));
-			tegra_gpio_writel(bank->int_enb[p], GPIO_INT_ENB(gpio));
+			tegra_gpio_writel(tgi, bank->cnf[p],
+					  GPIO_CNF(tgi, gpio));
+
+			if (tgi->soc->debounce_supported) {
+				tegra_gpio_writel(tgi, bank->dbc_cnt[p],
+						  GPIO_DBC_CNT(tgi, gpio));
+				tegra_gpio_writel(tgi, bank->dbc_enb[p],
+						  GPIO_MSK_DBC_EN(tgi, gpio));
+			}
+
+			tegra_gpio_writel(tgi, bank->out[p],
+					  GPIO_OUT(tgi, gpio));
+			tegra_gpio_writel(tgi, bank->oe[p],
+					  GPIO_OE(tgi, gpio));
+			tegra_gpio_writel(tgi, bank->int_lvl[p],
+					  GPIO_INT_LVL(tgi, gpio));
+			tegra_gpio_writel(tgi, bank->int_enb[p],
+					  GPIO_INT_ENB(tgi, gpio));
 		}
 	}
 
@@ -331,25 +430,39 @@
 
 static int tegra_gpio_suspend(struct device *dev)
 {
+	struct platform_device *pdev = to_platform_device(dev);
+	struct tegra_gpio_info *tgi = platform_get_drvdata(pdev);
 	unsigned long flags;
 	int b;
 	int p;
 
 	local_irq_save(flags);
-	for (b = 0; b < tegra_gpio_bank_count; b++) {
-		struct tegra_gpio_bank *bank = &tegra_gpio_banks[b];
+	for (b = 0; b < tgi->bank_count; b++) {
+		struct tegra_gpio_bank *bank = &tgi->bank_info[b];
 
 		for (p = 0; p < ARRAY_SIZE(bank->oe); p++) {
 			unsigned int gpio = (b<<5) | (p<<3);
-			bank->cnf[p] = tegra_gpio_readl(GPIO_CNF(gpio));
-			bank->out[p] = tegra_gpio_readl(GPIO_OUT(gpio));
-			bank->oe[p] = tegra_gpio_readl(GPIO_OE(gpio));
-			bank->int_enb[p] = tegra_gpio_readl(GPIO_INT_ENB(gpio));
-			bank->int_lvl[p] = tegra_gpio_readl(GPIO_INT_LVL(gpio));
+			bank->cnf[p] = tegra_gpio_readl(tgi,
+							GPIO_CNF(tgi, gpio));
+			bank->out[p] = tegra_gpio_readl(tgi,
+							GPIO_OUT(tgi, gpio));
+			bank->oe[p] = tegra_gpio_readl(tgi,
+						       GPIO_OE(tgi, gpio));
+			if (tgi->soc->debounce_supported) {
+				bank->dbc_enb[p] = tegra_gpio_readl(tgi,
+						GPIO_MSK_DBC_EN(tgi, gpio));
+				bank->dbc_enb[p] = (bank->dbc_enb[p] << 8) |
+							bank->dbc_enb[p];
+			}
+
+			bank->int_enb[p] = tegra_gpio_readl(tgi,
+						GPIO_INT_ENB(tgi, gpio));
+			bank->int_lvl[p] = tegra_gpio_readl(tgi,
+						GPIO_INT_LVL(tgi, gpio));
 
 			/* Enable gpio irq for wake up source */
-			tegra_gpio_writel(bank->wake_enb[p],
-					  GPIO_INT_ENB(gpio));
+			tegra_gpio_writel(tgi, bank->wake_enb[p],
+					  GPIO_INT_ENB(tgi, gpio));
 		}
 	}
 	local_irq_restore(flags);
@@ -382,22 +495,23 @@
 
 static int dbg_gpio_show(struct seq_file *s, void *unused)
 {
+	struct tegra_gpio_info *tgi = s->private;
 	int i;
 	int j;
 
-	for (i = 0; i < tegra_gpio_bank_count; i++) {
+	for (i = 0; i < tgi->bank_count; i++) {
 		for (j = 0; j < 4; j++) {
 			int gpio = tegra_gpio_compose(i, j, 0);
 			seq_printf(s,
 				"%d:%d %02x %02x %02x %02x %02x %02x %06x\n",
 				i, j,
-				tegra_gpio_readl(GPIO_CNF(gpio)),
-				tegra_gpio_readl(GPIO_OE(gpio)),
-				tegra_gpio_readl(GPIO_OUT(gpio)),
-				tegra_gpio_readl(GPIO_IN(gpio)),
-				tegra_gpio_readl(GPIO_INT_STA(gpio)),
-				tegra_gpio_readl(GPIO_INT_ENB(gpio)),
-				tegra_gpio_readl(GPIO_INT_LVL(gpio)));
+				tegra_gpio_readl(tgi, GPIO_CNF(tgi, gpio)),
+				tegra_gpio_readl(tgi, GPIO_OE(tgi, gpio)),
+				tegra_gpio_readl(tgi, GPIO_OUT(tgi, gpio)),
+				tegra_gpio_readl(tgi, GPIO_IN(tgi, gpio)),
+				tegra_gpio_readl(tgi, GPIO_INT_STA(tgi, gpio)),
+				tegra_gpio_readl(tgi, GPIO_INT_ENB(tgi, gpio)),
+				tegra_gpio_readl(tgi, GPIO_INT_LVL(tgi, gpio)));
 		}
 	}
 	return 0;
@@ -405,7 +519,7 @@
 
 static int dbg_gpio_open(struct inode *inode, struct file *file)
 {
-	return single_open(file, dbg_gpio_show, &inode->i_private);
+	return single_open(file, dbg_gpio_show, inode->i_private);
 }
 
 static const struct file_operations debug_fops = {
@@ -415,66 +529,28 @@
 	.release	= single_release,
 };
 
-static void tegra_gpio_debuginit(void)
+static void tegra_gpio_debuginit(struct tegra_gpio_info *tgi)
 {
 	(void) debugfs_create_file("tegra_gpio", S_IRUGO,
-					NULL, NULL, &debug_fops);
+					NULL, tgi, &debug_fops);
 }
 
 #else
 
-static inline void tegra_gpio_debuginit(void)
+static inline void tegra_gpio_debuginit(struct tegra_gpio_info *tgi)
 {
 }
 
 #endif
 
-static struct irq_chip tegra_gpio_irq_chip = {
-	.name		= "GPIO",
-	.irq_ack	= tegra_gpio_irq_ack,
-	.irq_mask	= tegra_gpio_irq_mask,
-	.irq_unmask	= tegra_gpio_irq_unmask,
-	.irq_set_type	= tegra_gpio_irq_set_type,
-	.irq_shutdown	= tegra_gpio_irq_shutdown,
-#ifdef CONFIG_PM_SLEEP
-	.irq_set_wake	= tegra_gpio_irq_set_wake,
-#endif
-};
-
 static const struct dev_pm_ops tegra_gpio_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(tegra_gpio_suspend, tegra_gpio_resume)
 };
 
-struct tegra_gpio_soc_config {
-	u32 bank_stride;
-	u32 upper_offset;
-};
-
-static struct tegra_gpio_soc_config tegra20_gpio_config = {
-	.bank_stride = 0x80,
-	.upper_offset = 0x800,
-};
-
-static struct tegra_gpio_soc_config tegra30_gpio_config = {
-	.bank_stride = 0x100,
-	.upper_offset = 0x80,
-};
-
-static const struct of_device_id tegra_gpio_of_match[] = {
-	{ .compatible = "nvidia,tegra30-gpio", .data = &tegra30_gpio_config },
-	{ .compatible = "nvidia,tegra20-gpio", .data = &tegra20_gpio_config },
-	{ },
-};
-
-/* This lock class tells lockdep that GPIO irqs are in a different
- * category than their parents, so it won't report false recursion.
- */
-static struct lock_class_key gpio_lock_class;
-
 static int tegra_gpio_probe(struct platform_device *pdev)
 {
-	const struct of_device_id *match;
-	struct tegra_gpio_soc_config *config;
+	const struct tegra_gpio_soc_config *config;
+	struct tegra_gpio_info *tgi;
 	struct resource *res;
 	struct tegra_gpio_bank *bank;
 	int ret;
@@ -482,102 +558,153 @@
 	int i;
 	int j;
 
-	dev = &pdev->dev;
-
-	match = of_match_device(tegra_gpio_of_match, &pdev->dev);
-	if (!match) {
+	config = of_device_get_match_data(&pdev->dev);
+	if (!config) {
 		dev_err(&pdev->dev, "Error: No device match found\n");
 		return -ENODEV;
 	}
-	config = (struct tegra_gpio_soc_config *)match->data;
 
-	tegra_gpio_bank_stride = config->bank_stride;
-	tegra_gpio_upper_offset = config->upper_offset;
+	tgi = devm_kzalloc(&pdev->dev, sizeof(*tgi), GFP_KERNEL);
+	if (!tgi)
+		return -ENODEV;
+
+	tgi->soc = config;
+	tgi->dev = &pdev->dev;
 
 	for (;;) {
-		res = platform_get_resource(pdev, IORESOURCE_IRQ, tegra_gpio_bank_count);
+		res = platform_get_resource(pdev, IORESOURCE_IRQ,
+					    tgi->bank_count);
 		if (!res)
 			break;
-		tegra_gpio_bank_count++;
+		tgi->bank_count++;
 	}
-	if (!tegra_gpio_bank_count) {
+	if (!tgi->bank_count) {
 		dev_err(&pdev->dev, "Missing IRQ resource\n");
 		return -ENODEV;
 	}
 
-	tegra_gpio_chip.ngpio = tegra_gpio_bank_count * 32;
+	tgi->gc.label			= "tegra-gpio";
+	tgi->gc.request			= tegra_gpio_request;
+	tgi->gc.free			= tegra_gpio_free;
+	tgi->gc.direction_input		= tegra_gpio_direction_input;
+	tgi->gc.get			= tegra_gpio_get;
+	tgi->gc.direction_output	= tegra_gpio_direction_output;
+	tgi->gc.set			= tegra_gpio_set;
+	tgi->gc.get_direction		= tegra_gpio_get_direction;
+	tgi->gc.to_irq			= tegra_gpio_to_irq;
+	tgi->gc.base			= 0;
+	tgi->gc.ngpio			= tgi->bank_count * 32;
+	tgi->gc.parent			= &pdev->dev;
+	tgi->gc.of_node			= pdev->dev.of_node;
 
-	tegra_gpio_banks = devm_kzalloc(&pdev->dev,
-			tegra_gpio_bank_count * sizeof(*tegra_gpio_banks),
-			GFP_KERNEL);
-	if (!tegra_gpio_banks)
+	tgi->ic.name			= "GPIO";
+	tgi->ic.irq_ack			= tegra_gpio_irq_ack;
+	tgi->ic.irq_mask		= tegra_gpio_irq_mask;
+	tgi->ic.irq_unmask		= tegra_gpio_irq_unmask;
+	tgi->ic.irq_set_type		= tegra_gpio_irq_set_type;
+	tgi->ic.irq_shutdown		= tegra_gpio_irq_shutdown;
+#ifdef CONFIG_PM_SLEEP
+	tgi->ic.irq_set_wake		= tegra_gpio_irq_set_wake;
+#endif
+
+	platform_set_drvdata(pdev, tgi);
+
+	if (config->debounce_supported)
+		tgi->gc.set_debounce = tegra_gpio_set_debounce;
+
+	tgi->bank_info = devm_kzalloc(&pdev->dev, tgi->bank_count *
+				      sizeof(*tgi->bank_info), GFP_KERNEL);
+	if (!tgi->bank_info)
 		return -ENODEV;
 
-	irq_domain = irq_domain_add_linear(pdev->dev.of_node,
-					   tegra_gpio_chip.ngpio,
-					   &irq_domain_simple_ops, NULL);
-	if (!irq_domain)
+	tgi->irq_domain = irq_domain_add_linear(pdev->dev.of_node,
+						tgi->gc.ngpio,
+						&irq_domain_simple_ops, NULL);
+	if (!tgi->irq_domain)
 		return -ENODEV;
 
-	for (i = 0; i < tegra_gpio_bank_count; i++) {
+	for (i = 0; i < tgi->bank_count; i++) {
 		res = platform_get_resource(pdev, IORESOURCE_IRQ, i);
 		if (!res) {
 			dev_err(&pdev->dev, "Missing IRQ resource\n");
 			return -ENODEV;
 		}
 
-		bank = &tegra_gpio_banks[i];
+		bank = &tgi->bank_info[i];
 		bank->bank = i;
 		bank->irq = res->start;
+		bank->tgi = tgi;
 	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	regs = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(regs))
-		return PTR_ERR(regs);
+	tgi->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(tgi->regs))
+		return PTR_ERR(tgi->regs);
 
-	for (i = 0; i < tegra_gpio_bank_count; i++) {
+	for (i = 0; i < tgi->bank_count; i++) {
 		for (j = 0; j < 4; j++) {
 			int gpio = tegra_gpio_compose(i, j, 0);
-			tegra_gpio_writel(0x00, GPIO_INT_ENB(gpio));
+			tegra_gpio_writel(tgi, 0x00, GPIO_INT_ENB(tgi, gpio));
 		}
 	}
 
-	tegra_gpio_chip.of_node = pdev->dev.of_node;
-
-	ret = devm_gpiochip_add_data(&pdev->dev, &tegra_gpio_chip, NULL);
+	ret = devm_gpiochip_add_data(&pdev->dev, &tgi->gc, tgi);
 	if (ret < 0) {
-		irq_domain_remove(irq_domain);
+		irq_domain_remove(tgi->irq_domain);
 		return ret;
 	}
 
-	for (gpio = 0; gpio < tegra_gpio_chip.ngpio; gpio++) {
-		int irq = irq_create_mapping(irq_domain, gpio);
+	for (gpio = 0; gpio < tgi->gc.ngpio; gpio++) {
+		int irq = irq_create_mapping(tgi->irq_domain, gpio);
 		/* No validity check; all Tegra GPIOs are valid IRQs */
 
-		bank = &tegra_gpio_banks[GPIO_BANK(gpio)];
+		bank = &tgi->bank_info[GPIO_BANK(gpio)];
 
-		irq_set_lockdep_class(irq, &gpio_lock_class);
+		irq_set_lockdep_class(irq, &tgi->lock_class);
 		irq_set_chip_data(irq, bank);
-		irq_set_chip_and_handler(irq, &tegra_gpio_irq_chip,
-					 handle_simple_irq);
+		irq_set_chip_and_handler(irq, &tgi->ic, handle_simple_irq);
 	}
 
-	for (i = 0; i < tegra_gpio_bank_count; i++) {
-		bank = &tegra_gpio_banks[i];
+	for (i = 0; i < tgi->bank_count; i++) {
+		bank = &tgi->bank_info[i];
 
 		irq_set_chained_handler_and_data(bank->irq,
 						 tegra_gpio_irq_handler, bank);
 
-		for (j = 0; j < 4; j++)
+		for (j = 0; j < 4; j++) {
 			spin_lock_init(&bank->lvl_lock[j]);
+			spin_lock_init(&bank->dbc_lock[j]);
+		}
 	}
 
-	tegra_gpio_debuginit();
+	tegra_gpio_debuginit(tgi);
 
 	return 0;
 }
 
+static const struct tegra_gpio_soc_config tegra20_gpio_config = {
+	.bank_stride = 0x80,
+	.upper_offset = 0x800,
+};
+
+static const struct tegra_gpio_soc_config tegra30_gpio_config = {
+	.bank_stride = 0x100,
+	.upper_offset = 0x80,
+};
+
+static const struct tegra_gpio_soc_config tegra210_gpio_config = {
+	.debounce_supported = true,
+	.bank_stride = 0x100,
+	.upper_offset = 0x80,
+};
+
+static const struct of_device_id tegra_gpio_of_match[] = {
+	{ .compatible = "nvidia,tegra210-gpio", .data = &tegra210_gpio_config },
+	{ .compatible = "nvidia,tegra30-gpio", .data = &tegra30_gpio_config },
+	{ .compatible = "nvidia,tegra20-gpio", .data = &tegra20_gpio_config },
+	{ },
+};
+
 static struct platform_driver tegra_gpio_driver = {
 	.driver		= {
 		.name	= "tegra-gpio",
diff --git a/drivers/gpio/gpio-timberdale.c b/drivers/gpio/gpio-timberdale.c
index 85ed608..181f86c 100644
--- a/drivers/gpio/gpio-timberdale.c
+++ b/drivers/gpio/gpio-timberdale.c
@@ -1,5 +1,6 @@
 /*
  * Timberdale FPGA GPIO driver
+ * Author: Mocean Laboratories
  * Copyright (c) 2009 Intel Corporation
  *
  * This program is free software; you can redistribute it and/or modify
@@ -20,7 +21,7 @@
  * Timberdale FPGA GPIO
  */
 
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/irq.h>
@@ -290,40 +291,14 @@
 	return 0;
 }
 
-static int timbgpio_remove(struct platform_device *pdev)
-{
-	struct timbgpio_platform_data *pdata = dev_get_platdata(&pdev->dev);
-	struct timbgpio *tgpio = platform_get_drvdata(pdev);
-	int irq = platform_get_irq(pdev, 0);
-
-	if (irq >= 0 && tgpio->irq_base > 0) {
-		int i;
-		for (i = 0; i < pdata->nr_pins; i++) {
-			irq_set_chip(tgpio->irq_base + i, NULL);
-			irq_set_chip_data(tgpio->irq_base + i, NULL);
-		}
-
-		irq_set_handler(irq, NULL);
-		irq_set_handler_data(irq, NULL);
-	}
-
-	return 0;
-}
-
 static struct platform_driver timbgpio_platform_driver = {
 	.driver = {
-		.name	= DRIVER_NAME,
+		.name			= DRIVER_NAME,
+		.suppress_bind_attrs	= true,
 	},
 	.probe		= timbgpio_probe,
-	.remove		= timbgpio_remove,
 };
 
 /*--------------------------------------------------------------------------*/
 
-module_platform_driver(timbgpio_platform_driver);
-
-MODULE_DESCRIPTION("Timberdale GPIO driver");
-MODULE_LICENSE("GPL v2");
-MODULE_AUTHOR("Mocean Laboratories");
-MODULE_ALIAS("platform:"DRIVER_NAME);
-
+builtin_platform_driver(timbgpio_platform_driver);
diff --git a/drivers/gpio/gpio-tpic2810.c b/drivers/gpio/gpio-tpic2810.c
index 9f020aa..cace79c 100644
--- a/drivers/gpio/gpio-tpic2810.c
+++ b/drivers/gpio/gpio-tpic2810.c
@@ -57,39 +57,34 @@
 	return 0;
 }
 
-static void tpic2810_set(struct gpio_chip *chip, unsigned offset, int value)
+static void tpic2810_set_mask_bits(struct gpio_chip *chip, u8 mask, u8 bits)
 {
 	struct tpic2810 *gpio = gpiochip_get_data(chip);
+	u8 buffer;
+	int err;
 
 	mutex_lock(&gpio->lock);
 
-	if (value)
-		gpio->buffer |= BIT(offset);
-	else
-		gpio->buffer &= ~BIT(offset);
+	buffer = gpio->buffer & ~mask;
+	buffer |= (mask & bits);
 
-	i2c_smbus_write_byte_data(gpio->client, TPIC2810_WS_COMMAND,
-				  gpio->buffer);
+	err = i2c_smbus_write_byte_data(gpio->client, TPIC2810_WS_COMMAND,
+					buffer);
+	if (!err)
+		gpio->buffer = buffer;
 
 	mutex_unlock(&gpio->lock);
 }
 
+static void tpic2810_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	tpic2810_set_mask_bits(chip, BIT(offset), value ? BIT(offset) : 0);
+}
+
 static void tpic2810_set_multiple(struct gpio_chip *chip, unsigned long *mask,
 				  unsigned long *bits)
 {
-	struct tpic2810 *gpio = gpiochip_get_data(chip);
-
-	mutex_lock(&gpio->lock);
-
-	/* clear bits under mask */
-	gpio->buffer &= ~(*mask);
-	/* set bits under mask */
-	gpio->buffer |= ((*mask) & (*bits));
-
-	i2c_smbus_write_byte_data(gpio->client, TPIC2810_WS_COMMAND,
-				  gpio->buffer);
-
-	mutex_unlock(&gpio->lock);
+	tpic2810_set_mask_bits(chip, *mask, *bits);
 }
 
 static struct gpio_chip template_chip = {
diff --git a/drivers/gpio/gpio-tps65218.c b/drivers/gpio/gpio-tps65218.c
index 313c0e4..0eaeac8 100644
--- a/drivers/gpio/gpio-tps65218.c
+++ b/drivers/gpio/gpio-tps65218.c
@@ -101,16 +101,6 @@
 
 		break;
 	case 1:
-		/* GP02 is push-pull by default, can be set as open drain. */
-		if (gpiochip_line_is_open_drain(gc, offset)) {
-			ret = tps65218_clear_bits(tps65218,
-						  TPS65218_REG_CONFIG1,
-						  TPS65218_CONFIG1_GPO2_BUF,
-						  TPS65218_PROTECT_L1);
-			if (ret)
-				return ret;
-		}
-
 		/* Setup GPO2 */
 		ret = tps65218_clear_bits(tps65218, TPS65218_REG_CONFIG1,
 					  TPS65218_CONFIG1_IO1_SEL,
@@ -148,6 +138,40 @@
 	return 0;
 }
 
+static int tps65218_gpio_set_single_ended(struct gpio_chip *gc,
+					  unsigned offset,
+					  enum single_ended_mode mode)
+{
+	struct tps65218_gpio *tps65218_gpio = gpiochip_get_data(gc);
+	struct tps65218 *tps65218 = tps65218_gpio->tps65218;
+
+	switch (offset) {
+	case 0:
+	case 2:
+		/* GPO1 is hardwired to be open drain */
+		if (mode == LINE_MODE_OPEN_DRAIN)
+			return 0;
+		return -ENOTSUPP;
+	case 1:
+		/* GPO2 is push-pull by default, can be set as open drain. */
+		if (mode == LINE_MODE_OPEN_DRAIN)
+			return tps65218_clear_bits(tps65218,
+						   TPS65218_REG_CONFIG1,
+						   TPS65218_CONFIG1_GPO2_BUF,
+						   TPS65218_PROTECT_L1);
+		if (mode == LINE_MODE_PUSH_PULL)
+			return tps65218_set_bits(tps65218,
+						 TPS65218_REG_CONFIG1,
+						 TPS65218_CONFIG1_GPO2_BUF,
+						 TPS65218_CONFIG1_GPO2_BUF,
+						 TPS65218_PROTECT_L1);
+		return -ENOTSUPP;
+	default:
+		break;
+	}
+	return -ENOTSUPP;
+}
+
 static struct gpio_chip template_chip = {
 	.label			= "gpio-tps65218",
 	.owner			= THIS_MODULE,
@@ -156,6 +180,7 @@
 	.direction_input	= tps65218_gpio_input,
 	.get			= tps65218_gpio_get,
 	.set			= tps65218_gpio_set,
+	.set_single_ended	= tps65218_gpio_set_single_ended,
 	.can_sleep		= true,
 	.ngpio			= 3,
 	.base			= -1,
diff --git a/drivers/gpio/gpio-tps6586x.c b/drivers/gpio/gpio-tps6586x.c
index c88bdc8..6b15e68 100644
--- a/drivers/gpio/gpio-tps6586x.c
+++ b/drivers/gpio/gpio-tps6586x.c
@@ -24,7 +24,7 @@
 #include <linux/errno.h>
 #include <linux/gpio.h>
 #include <linux/kernel.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/mfd/tps6586x.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
@@ -140,14 +140,3 @@
 	return platform_driver_register(&tps6586x_gpio_driver);
 }
 subsys_initcall(tps6586x_gpio_init);
-
-static void __exit tps6586x_gpio_exit(void)
-{
-	platform_driver_unregister(&tps6586x_gpio_driver);
-}
-module_exit(tps6586x_gpio_exit);
-
-MODULE_ALIAS("platform:tps6586x-gpio");
-MODULE_DESCRIPTION("GPIO interface for TPS6586X PMIC");
-MODULE_AUTHOR("Laxman Dewangan <ldewangan@nvidia.com>");
-MODULE_LICENSE("GPL");
diff --git a/drivers/gpio/gpio-tps65910.c b/drivers/gpio/gpio-tps65910.c
index cdbd7c7..0ae6a5a 100644
--- a/drivers/gpio/gpio-tps65910.c
+++ b/drivers/gpio/gpio-tps65910.c
@@ -4,7 +4,7 @@
  * Copyright 2010 Texas Instruments Inc.
  *
  * Author: Graeme Gregory <gg@slimlogic.co.uk>
- * Author: Jorge Eduardo Candelaria jedu@slimlogic.co.uk>
+ * Author: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
  *
  *  This program is free software; you can redistribute it and/or modify it
  *  under  the terms of the GNU General  Public License as published by the
@@ -14,7 +14,7 @@
  */
 
 #include <linux/kernel.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/errno.h>
 #include <linux/gpio.h>
 #include <linux/i2c.h>
@@ -193,15 +193,3 @@
 	return platform_driver_register(&tps65910_gpio_driver);
 }
 subsys_initcall(tps65910_gpio_init);
-
-static void __exit tps65910_gpio_exit(void)
-{
-	platform_driver_unregister(&tps65910_gpio_driver);
-}
-module_exit(tps65910_gpio_exit);
-
-MODULE_AUTHOR("Graeme Gregory <gg@slimlogic.co.uk>");
-MODULE_AUTHOR("Jorge Eduardo Candelaria jedu@slimlogic.co.uk>");
-MODULE_DESCRIPTION("GPIO interface for TPS65910/TPS6511 PMICs");
-MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform:tps65910-gpio");
diff --git a/drivers/gpio/gpio-vx855.c b/drivers/gpio/gpio-vx855.c
index 8cdb9f7..4e45012 100644
--- a/drivers/gpio/gpio-vx855.c
+++ b/drivers/gpio/gpio-vx855.c
@@ -186,6 +186,28 @@
 	return 0;
 }
 
+static int vx855gpio_set_single_ended(struct gpio_chip *gpio,
+				      unsigned int nr,
+				      enum single_ended_mode mode)
+{
+	/* The GPI cannot be single-ended */
+	if (nr < NR_VX855_GPI)
+		return -EINVAL;
+
+	/* The GPO's are push-pull */
+	if (nr < NR_VX855_GPInO) {
+		if (mode != LINE_MODE_PUSH_PULL)
+			return -ENOTSUPP;
+		return 0;
+	}
+
+	/* The GPIO's are open drain */
+	if (mode != LINE_MODE_OPEN_DRAIN)
+		return -ENOTSUPP;
+
+	return 0;
+}
+
 static const char *vx855gpio_names[NR_VX855_GP] = {
 	"VX855_GPI0", "VX855_GPI1", "VX855_GPI2", "VX855_GPI3", "VX855_GPI4",
 	"VX855_GPI5", "VX855_GPI6", "VX855_GPI7", "VX855_GPI8", "VX855_GPI9",
@@ -209,6 +231,7 @@
 	c->direction_output = vx855gpio_direction_output;
 	c->get = vx855gpio_get;
 	c->set = vx855gpio_set;
+	c->set_single_ended = vx855gpio_set_single_ended;
 	c->dbg_show = NULL;
 	c->base = 0;
 	c->ngpio = NR_VX855_GP;
diff --git a/drivers/gpio/gpio-wm831x.c b/drivers/gpio/gpio-wm831x.c
index 18cb0f5..41ec783 100644
--- a/drivers/gpio/gpio-wm831x.c
+++ b/drivers/gpio/gpio-wm831x.c
@@ -132,6 +132,28 @@
 	return wm831x_set_bits(wm831x, reg, WM831X_GPN_FN_MASK, fn);
 }
 
+static int wm831x_set_single_ended(struct gpio_chip *chip,
+				   unsigned int offset,
+				   enum single_ended_mode mode)
+{
+	struct wm831x_gpio *wm831x_gpio = gpiochip_get_data(chip);
+	struct wm831x *wm831x = wm831x_gpio->wm831x;
+	int reg = WM831X_GPIO1_CONTROL + offset;
+
+	switch (mode) {
+	case LINE_MODE_OPEN_DRAIN:
+		return wm831x_set_bits(wm831x, reg,
+				       WM831X_GPN_OD_MASK, WM831X_GPN_OD);
+	case LINE_MODE_PUSH_PULL:
+		return wm831x_set_bits(wm831x, reg,
+				       WM831X_GPN_OD_MASK, 0);
+	default:
+		break;
+	}
+
+	return -ENOTSUPP;
+}
+
 #ifdef CONFIG_DEBUG_FS
 static void wm831x_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
 {
@@ -216,7 +238,7 @@
 			   pull,
 			   powerdomain,
 			   reg & WM831X_GPN_POL ? "" : " inverted",
-			   reg & WM831X_GPN_OD ? "open-drain" : "CMOS",
+			   reg & WM831X_GPN_OD ? "open-drain" : "push-pull",
 			   tristated ? " tristated" : "",
 			   reg);
 	}
@@ -234,6 +256,7 @@
 	.set			= wm831x_gpio_set,
 	.to_irq			= wm831x_gpio_to_irq,
 	.set_debounce		= wm831x_gpio_set_debounce,
+	.set_single_ended	= wm831x_set_single_ended,
 	.dbg_show		= wm831x_gpio_dbg_show,
 	.can_sleep		= true,
 };
diff --git a/drivers/gpio/gpio-wm8994.c b/drivers/gpio/gpio-wm8994.c
index b089df9..744af38 100644
--- a/drivers/gpio/gpio-wm8994.c
+++ b/drivers/gpio/gpio-wm8994.c
@@ -103,6 +103,28 @@
 	wm8994_set_bits(wm8994, WM8994_GPIO_1 + offset, WM8994_GPN_LVL, value);
 }
 
+static int wm8994_gpio_set_single_ended(struct gpio_chip *chip,
+					unsigned int offset,
+					enum single_ended_mode mode)
+{
+	struct wm8994_gpio *wm8994_gpio = gpiochip_get_data(chip);
+	struct wm8994 *wm8994 = wm8994_gpio->wm8994;
+
+	switch (mode) {
+	case LINE_MODE_OPEN_DRAIN:
+		return wm8994_set_bits(wm8994, WM8994_GPIO_1 + offset,
+				       WM8994_GPN_OP_CFG_MASK,
+				       WM8994_GPN_OP_CFG);
+	case LINE_MODE_PUSH_PULL:
+		return wm8994_set_bits(wm8994, WM8994_GPIO_1 + offset,
+				       WM8994_GPN_OP_CFG_MASK, 0);
+	default:
+		break;
+	}
+
+	return -ENOTSUPP;
+}
+
 static int wm8994_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
 {
 	struct wm8994_gpio *wm8994_gpio = gpiochip_get_data(chip);
@@ -217,7 +239,7 @@
 		if (reg & WM8994_GPN_OP_CFG)
 			seq_printf(s, "open drain ");
 		else
-			seq_printf(s, "CMOS ");
+			seq_printf(s, "push-pull ");
 
 		seq_printf(s, "%s (%x)\n",
 			   wm8994_gpio_fn(reg & WM8994_GPN_FN_MASK), reg);
@@ -235,6 +257,7 @@
 	.get			= wm8994_gpio_get,
 	.direction_output	= wm8994_gpio_direction_out,
 	.set			= wm8994_gpio_set,
+	.set_single_ended	= wm8994_gpio_set_single_ended,
 	.to_irq			= wm8994_gpio_to_irq,
 	.dbg_show		= wm8994_gpio_dbg_show,
 	.can_sleep		= true,
diff --git a/drivers/gpio/gpio-xgene-sb.c b/drivers/gpio/gpio-xgene-sb.c
index 31cbcb8..0332586 100644
--- a/drivers/gpio/gpio-xgene-sb.c
+++ b/drivers/gpio/gpio-xgene-sb.c
@@ -216,23 +216,10 @@
 			&parent_fwspec);
 }
 
-static void xgene_gpio_sb_domain_free(struct irq_domain *domain,
-		unsigned int virq,
-		unsigned int nr_irqs)
-{
-	struct irq_data *d;
-	unsigned int i;
-
-	for (i = 0; i < nr_irqs; i++) {
-		d = irq_domain_get_irq_data(domain, virq + i);
-		irq_domain_reset_irq_data(d);
-	}
-}
-
 static const struct irq_domain_ops xgene_gpio_sb_domain_ops = {
 	.translate      = xgene_gpio_sb_domain_translate,
 	.alloc          = xgene_gpio_sb_domain_alloc,
-	.free           = xgene_gpio_sb_domain_free,
+	.free           = irq_domain_free_irqs_common,
 	.activate	= xgene_gpio_sb_domain_activate,
 	.deactivate	= xgene_gpio_sb_domain_deactivate,
 };
diff --git a/drivers/gpio/gpio-xgene.c b/drivers/gpio/gpio-xgene.c
index 0dc9161..40a8881 100644
--- a/drivers/gpio/gpio-xgene.c
+++ b/drivers/gpio/gpio-xgene.c
@@ -17,7 +17,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
-#include <linux/module.h>
+#include <linux/acpi.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/io.h>
@@ -85,6 +85,17 @@
 	spin_unlock_irqrestore(&chip->lock, flags);
 }
 
+static int xgene_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
+{
+	struct xgene_gpio *chip = gpiochip_get_data(gc);
+	unsigned long bank_offset, bit_offset;
+
+	bank_offset = GPIO_SET_DR_OFFSET + GPIO_BANK_OFFSET(offset);
+	bit_offset = GPIO_BIT_OFFSET(offset);
+
+	return !!(ioread32(chip->base + bank_offset) & BIT(bit_offset));
+}
+
 static int xgene_gpio_dir_in(struct gpio_chip *gc, unsigned int offset)
 {
 	struct xgene_gpio *chip = gpiochip_get_data(gc);
@@ -189,6 +200,7 @@
 
 	spin_lock_init(&gpio->lock);
 	gpio->chip.parent = &pdev->dev;
+	gpio->chip.get_direction = xgene_gpio_get_direction;
 	gpio->chip.direction_input = xgene_gpio_dir_in;
 	gpio->chip.direction_output = xgene_gpio_dir_out;
 	gpio->chip.get = xgene_gpio_get;
@@ -216,19 +228,21 @@
 	{ .compatible = "apm,xgene-gpio", },
 	{},
 };
-MODULE_DEVICE_TABLE(of, xgene_gpio_of_match);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id xgene_gpio_acpi_match[] = {
+	{ "APMC0D14", 0 },
+	{ },
+};
+#endif
 
 static struct platform_driver xgene_gpio_driver = {
 	.driver = {
 		.name = "xgene-gpio",
 		.of_match_table = xgene_gpio_of_match,
+		.acpi_match_table = ACPI_PTR(xgene_gpio_acpi_match),
 		.pm     = XGENE_GPIO_PM_OPS,
 	},
 	.probe = xgene_gpio_probe,
 };
-
-module_platform_driver(xgene_gpio_driver);
-
-MODULE_AUTHOR("Feng Kan <fkan@apm.com>");
-MODULE_DESCRIPTION("APM X-Gene GPIO driver");
-MODULE_LICENSE("GPL");
+builtin_platform_driver(xgene_gpio_driver);
diff --git a/drivers/gpio/gpio-xlp.c b/drivers/gpio/gpio-xlp.c
index aa5813d..08897dc 100644
--- a/drivers/gpio/gpio-xlp.c
+++ b/drivers/gpio/gpio-xlp.c
@@ -85,7 +85,8 @@
 	XLP_GPIO_VARIANT_XLP316,
 	XLP_GPIO_VARIANT_XLP208,
 	XLP_GPIO_VARIANT_XLP980,
-	XLP_GPIO_VARIANT_XLP532
+	XLP_GPIO_VARIANT_XLP532,
+	GPIO_VARIANT_VULCAN
 };
 
 struct xlp_gpio_priv {
@@ -285,6 +286,10 @@
 		.compatible = "netlogic,xlp532-gpio",
 		.data	    = (void *)XLP_GPIO_VARIANT_XLP532,
 	},
+	{
+		.compatible = "brcm,vulcan-gpio",
+		.data	    = (void *)GPIO_VARIANT_VULCAN,
+	},
 	{ /* sentinel */ },
 };
 MODULE_DEVICE_TABLE(of, xlp_gpio_of_ids);
@@ -347,6 +352,7 @@
 		break;
 	case XLP_GPIO_VARIANT_XLP980:
 	case XLP_GPIO_VARIANT_XLP532:
+	case GPIO_VARIANT_VULCAN:
 		priv->gpio_out_en = gpio_base + GPIO_9XX_OUTPUT_EN;
 		priv->gpio_paddrv = gpio_base + GPIO_9XX_PADDRV;
 		priv->gpio_intr_stat = gpio_base + GPIO_9XX_INT_STAT;
@@ -354,7 +360,12 @@
 		priv->gpio_intr_pol = gpio_base + GPIO_9XX_INT_POL;
 		priv->gpio_intr_en = gpio_base + GPIO_9XX_INT_EN00;
 
-		ngpio = (soc_type == XLP_GPIO_VARIANT_XLP980) ? 66 : 67;
+		if (soc_type == XLP_GPIO_VARIANT_XLP980)
+			ngpio = 66;
+		else if (soc_type == XLP_GPIO_VARIANT_XLP532)
+			ngpio = 67;
+		else
+			ngpio = 70;
 		break;
 	default:
 		dev_err(&pdev->dev, "Unknown Processor type!\n");
@@ -377,10 +388,14 @@
 	gc->get = xlp_gpio_get;
 
 	spin_lock_init(&priv->lock);
-	irq_base = irq_alloc_descs(-1, XLP_GPIO_IRQ_BASE, gc->ngpio, 0);
-	if (irq_base < 0) {
+	/* XLP has fixed IRQ range for GPIO interrupts */
+	if (soc_type == GPIO_VARIANT_VULCAN)
+		irq_base = irq_alloc_descs(-1, 0, gc->ngpio, 0);
+	else
+		irq_base = irq_alloc_descs(-1, XLP_GPIO_IRQ_BASE, gc->ngpio, 0);
+	if (IS_ERR_VALUE(irq_base)) {
 		dev_err(&pdev->dev, "Failed to allocate IRQ numbers\n");
-		return -ENODEV;
+		return irq_base;
 	}
 
 	err = gpiochip_add_data(gc, priv);
diff --git a/drivers/gpio/gpio-zevio.c b/drivers/gpio/gpio-zevio.c
index cda6d92..e23ef7b 100644
--- a/drivers/gpio/gpio-zevio.c
+++ b/drivers/gpio/gpio-zevio.c
@@ -10,7 +10,7 @@
 
 #include <linux/spinlock.h>
 #include <linux/errno.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/bitops.h>
 #include <linux/io.h>
 #include <linux/of_device.h>
@@ -203,32 +203,17 @@
 	return 0;
 }
 
-static int zevio_gpio_remove(struct platform_device *pdev)
-{
-	struct zevio_gpio *controller = platform_get_drvdata(pdev);
-
-	of_mm_gpiochip_remove(&controller->chip);
-
-	return 0;
-}
-
 static const struct of_device_id zevio_gpio_of_match[] = {
 	{ .compatible = "lsi,zevio-gpio", },
 	{ },
 };
 
-MODULE_DEVICE_TABLE(of, zevio_gpio_of_match);
-
 static struct platform_driver zevio_gpio_driver = {
 	.driver		= {
 		.name	= "gpio-zevio",
 		.of_match_table = zevio_gpio_of_match,
+		.suppress_bind_attrs = true,
 	},
 	.probe		= zevio_gpio_probe,
-	.remove		= zevio_gpio_remove,
 };
-module_platform_driver(zevio_gpio_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Fabian Vogt <fabian@ritter-vogt.de>");
-MODULE_DESCRIPTION("LSI ZEVIO SoC GPIO driver");
+builtin_platform_driver(zevio_gpio_driver);
diff --git a/drivers/gpio/gpio-zx.c b/drivers/gpio/gpio-zx.c
index 47c79fa..93de8be 100644
--- a/drivers/gpio/gpio-zx.c
+++ b/drivers/gpio/gpio-zx.c
@@ -1,4 +1,8 @@
 /*
+ * ZTE ZX296702 GPIO driver
+ *
+ * Author: Jun Nie <jun.nie@linaro.org>
+ *
  * Copyright (C) 2015 Linaro Ltd.
  *
  * This program is free software; you can redistribute it and/or modify
@@ -10,7 +14,7 @@
 #include <linux/errno.h>
 #include <linux/gpio/driver.h>
 #include <linux/irqchip/chained_irq.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/of.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
@@ -282,7 +286,6 @@
 	},
 	{ },
 };
-MODULE_DEVICE_TABLE(of, zx_gpio_match);
 
 static struct platform_driver zx_gpio_driver = {
 	.probe		= zx_gpio_probe,
@@ -291,9 +294,4 @@
 		.of_match_table = of_match_ptr(zx_gpio_match),
 	},
 };
-
-module_platform_driver(zx_gpio_driver)
-
-MODULE_AUTHOR("Jun Nie <jun.nie@linaro.org>");
-MODULE_DESCRIPTION("ZTE ZX296702 GPIO driver");
-MODULE_LICENSE("GPL");
+builtin_platform_driver(zx_gpio_driver)
diff --git a/drivers/gpio/gpio-zynq.c b/drivers/gpio/gpio-zynq.c
index 66d3d24..75c6355 100644
--- a/drivers/gpio/gpio-zynq.c
+++ b/drivers/gpio/gpio-zynq.c
@@ -713,7 +713,7 @@
 	pm_runtime_enable(&pdev->dev);
 	ret = pm_runtime_get_sync(&pdev->dev);
 	if (ret < 0)
-		return ret;
+		goto err_pm_dis;
 
 	/* report a bug if gpio chip registration fails */
 	ret = gpiochip_add_data(chip, gpio);
@@ -745,6 +745,8 @@
 	gpiochip_remove(chip);
 err_pm_put:
 	pm_runtime_put(&pdev->dev);
+err_pm_dis:
+	pm_runtime_disable(&pdev->dev);
 
 	return ret;
 }
diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index 42a4bb7..d22dcc3 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -196,21 +196,68 @@
 }
 
 /**
+ * of_gpiochip_set_names() - set up the names of the lines
+ * @chip: GPIO chip whose lines should be named, if possible
+ */
+static void of_gpiochip_set_names(struct gpio_chip *gc)
+{
+	struct gpio_device *gdev = gc->gpiodev;
+	struct device_node *np = gc->of_node;
+	int i;
+	int nstrings;
+
+	nstrings = of_property_count_strings(np, "gpio-line-names");
+	if (nstrings <= 0)
+		/* Lines names not present */
+		return;
+
+	/* This is normally not what you want */
+	if (gdev->ngpio != nstrings)
+		dev_info(&gdev->dev, "gpio-line-names specifies %d line "
+			 "names but there are %d lines on the chip\n",
+			 nstrings, gdev->ngpio);
+
+	/*
+	 * Make sure to not index beyond the end of the number of descriptors
+	 * of the GPIO device.
+	 */
+	for (i = 0; i < gdev->ngpio; i++) {
+		const char *name;
+		int ret;
+
+		ret = of_property_read_string_index(np,
+						    "gpio-line-names",
+						    i,
+						    &name);
+		if (ret) {
+			if (ret != -ENODATA)
+                                dev_err(&gdev->dev,
+                                        "unable to name line %d: %d\n",
+                                        i, ret);
+			break;
+		}
+		gdev->descs[i].name = name;
+	}
+}
+
+/**
  * of_gpiochip_scan_gpios - Scan gpio-controller for gpio definitions
  * @chip:	gpio chip to act on
  *
  * This is only used by of_gpiochip_add to request/set GPIO initial
  * configuration.
+ * It retures error if it fails otherwise 0 on success.
  */
-static void of_gpiochip_scan_gpios(struct gpio_chip *chip)
+static int of_gpiochip_scan_gpios(struct gpio_chip *chip)
 {
 	struct gpio_desc *desc = NULL;
 	struct device_node *np;
 	const char *name;
 	enum gpio_lookup_flags lflags;
 	enum gpiod_flags dflags;
+	int ret;
 
-	for_each_child_of_node(chip->of_node, np) {
+	for_each_available_child_of_node(chip->of_node, np) {
 		if (!of_property_read_bool(np, "gpio-hog"))
 			continue;
 
@@ -218,9 +265,12 @@
 		if (IS_ERR(desc))
 			continue;
 
-		if (gpiod_hog(desc, name, lflags, dflags))
-			continue;
+		ret = gpiod_hog(desc, name, lflags, dflags);
+		if (ret < 0)
+			return ret;
 	}
+
+	return 0;
 }
 
 /**
@@ -440,11 +490,13 @@
 	if (status)
 		return status;
 
+	/* If the chip defines names itself, these take precedence */
+	if (!chip->names)
+		of_gpiochip_set_names(chip);
+
 	of_node_get(chip->of_node);
 
-	of_gpiochip_scan_gpios(chip);
-
-	return 0;
+	return of_gpiochip_scan_gpios(chip);
 }
 
 void of_gpiochip_remove(struct gpio_chip *chip)
diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index b747c76..d407f904 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -622,14 +622,31 @@
 		struct gpio_desc *desc = &gdev->descs[i];
 
 		desc->gdev = gdev;
-
-		/* REVISIT: most hardware initializes GPIOs as inputs (often
-		 * with pullups enabled) so power usage is minimized. Linux
-		 * code should set the gpio direction first thing; but until
-		 * it does, and in case chip->get_direction is not set, we may
-		 * expose the wrong direction in sysfs.
+		/*
+		 * REVISIT: most hardware initializes GPIOs as inputs
+		 * (often with pullups enabled) so power usage is
+		 * minimized. Linux code should set the gpio direction
+		 * first thing; but until it does, and in case
+		 * chip->get_direction is not set, we may expose the
+		 * wrong direction in sysfs.
 		 */
-		desc->flags = !chip->direction_input ? (1 << FLAG_IS_OUT) : 0;
+
+		if (chip->get_direction) {
+			/*
+			 * If we have .get_direction, set up the initial
+			 * direction flag from the hardware.
+			 */
+			int dir = chip->get_direction(chip, i);
+
+			if (!dir)
+				set_bit(FLAG_IS_OUT, &desc->flags);
+		} else if (!chip->direction_input) {
+			/*
+			 * If the chip lacks the .direction_input callback
+			 * we logically assume all lines are outputs.
+			 */
+			set_bit(FLAG_IS_OUT, &desc->flags);
+		}
 	}
 
 	spin_unlock_irqrestore(&gpio_lock, flags);
@@ -1547,8 +1564,8 @@
 
 static int _gpiod_direction_output_raw(struct gpio_desc *desc, int value)
 {
-	struct gpio_chip	*chip;
-	int			status = -EINVAL;
+	struct gpio_chip *gc = desc->gdev->chip;
+	int ret;
 
 	/* GPIOs used for IRQs shall not be set as output */
 	if (test_bit(FLAG_USED_AS_IRQ, &desc->flags)) {
@@ -1558,28 +1575,50 @@
 		return -EIO;
 	}
 
-	/* Open drain pin should not be driven to 1 */
-	if (value && test_bit(FLAG_OPEN_DRAIN,  &desc->flags))
-		return gpiod_direction_input(desc);
+	if (test_bit(FLAG_OPEN_DRAIN, &desc->flags)) {
+		/* First see if we can enable open drain in hardware */
+		if (gc->set_single_ended) {
+			ret = gc->set_single_ended(gc, gpio_chip_hwgpio(desc),
+						   LINE_MODE_OPEN_DRAIN);
+			if (!ret)
+				goto set_output_value;
+		}
+		/* Emulate open drain by not actively driving the line high */
+		if (value)
+			return gpiod_direction_input(desc);
+	}
+	else if (test_bit(FLAG_OPEN_SOURCE, &desc->flags)) {
+		if (gc->set_single_ended) {
+			ret = gc->set_single_ended(gc, gpio_chip_hwgpio(desc),
+						   LINE_MODE_OPEN_SOURCE);
+			if (!ret)
+				goto set_output_value;
+		}
+		/* Emulate open source by not actively driving the line low */
+		if (!value)
+			return gpiod_direction_input(desc);
+	} else {
+		/* Make sure to disable open drain/source hardware, if any */
+		if (gc->set_single_ended)
+			gc->set_single_ended(gc,
+					     gpio_chip_hwgpio(desc),
+					     LINE_MODE_PUSH_PULL);
+	}
 
-	/* Open source pin should not be driven to 0 */
-	if (!value && test_bit(FLAG_OPEN_SOURCE,  &desc->flags))
-		return gpiod_direction_input(desc);
-
-	chip = desc->gdev->chip;
-	if (!chip->set || !chip->direction_output) {
+set_output_value:
+	if (!gc->set || !gc->direction_output) {
 		gpiod_warn(desc,
 		       "%s: missing set() or direction_output() operations\n",
 		       __func__);
 		return -EIO;
 	}
 
-	status = chip->direction_output(chip, gpio_chip_hwgpio(desc), value);
-	if (status == 0)
+	ret = gc->direction_output(gc, gpio_chip_hwgpio(desc), value);
+	if (!ret)
 		set_bit(FLAG_IS_OUT, &desc->flags);
 	trace_gpio_value(desc_to_gpio(desc), 0, value);
-	trace_gpio_direction(desc_to_gpio(desc), 0, status);
-	return status;
+	trace_gpio_direction(desc_to_gpio(desc), 0, ret);
+	return ret;
 }
 
 /**
@@ -1841,10 +1880,10 @@
 	}
 }
 
-static void gpiod_set_array_value_priv(bool raw, bool can_sleep,
-				       unsigned int array_size,
-				       struct gpio_desc **desc_array,
-				       int *value_array)
+void gpiod_set_array_value_complex(bool raw, bool can_sleep,
+				   unsigned int array_size,
+				   struct gpio_desc **desc_array,
+				   int *value_array)
 {
 	int i = 0;
 
@@ -1950,8 +1989,8 @@
 {
 	if (!desc_array)
 		return;
-	gpiod_set_array_value_priv(true, false, array_size, desc_array,
-				   value_array);
+	gpiod_set_array_value_complex(true, false, array_size, desc_array,
+				      value_array);
 }
 EXPORT_SYMBOL_GPL(gpiod_set_raw_array_value);
 
@@ -1972,8 +2011,8 @@
 {
 	if (!desc_array)
 		return;
-	gpiod_set_array_value_priv(false, false, array_size, desc_array,
-				   value_array);
+	gpiod_set_array_value_complex(false, false, array_size, desc_array,
+				      value_array);
 }
 EXPORT_SYMBOL_GPL(gpiod_set_array_value);
 
@@ -1998,13 +2037,22 @@
  */
 int gpiod_to_irq(const struct gpio_desc *desc)
 {
-	struct gpio_chip	*chip;
-	int			offset;
+	struct gpio_chip *chip;
+	int offset;
 
 	VALIDATE_DESC(desc);
 	chip = desc->gdev->chip;
 	offset = gpio_chip_hwgpio(desc);
-	return chip->to_irq ? chip->to_irq(chip, offset) : -ENXIO;
+	if (chip->to_irq) {
+		int retirq = chip->to_irq(chip, offset);
+
+		/* Zero means NO_IRQ */
+		if (!retirq)
+			return -ENXIO;
+
+		return retirq;
+	}
+	return -ENXIO;
 }
 EXPORT_SYMBOL_GPL(gpiod_to_irq);
 
@@ -2176,8 +2224,8 @@
 	might_sleep_if(extra_checks);
 	if (!desc_array)
 		return;
-	gpiod_set_array_value_priv(true, true, array_size, desc_array,
-				   value_array);
+	gpiod_set_array_value_complex(true, true, array_size, desc_array,
+				      value_array);
 }
 EXPORT_SYMBOL_GPL(gpiod_set_raw_array_value_cansleep);
 
@@ -2199,8 +2247,8 @@
 	might_sleep_if(extra_checks);
 	if (!desc_array)
 		return;
-	gpiod_set_array_value_priv(false, true, array_size, desc_array,
-				   value_array);
+	gpiod_set_array_value_complex(false, true, array_size, desc_array,
+				      value_array);
 }
 EXPORT_SYMBOL_GPL(gpiod_set_array_value_cansleep);
 
@@ -2726,15 +2774,16 @@
 
 	local_desc = gpiochip_request_own_desc(chip, hwnum, name);
 	if (IS_ERR(local_desc)) {
-		pr_err("requesting hog GPIO %s (chip %s, offset %d) failed\n",
-		       name, chip->label, hwnum);
-		return PTR_ERR(local_desc);
+		status = PTR_ERR(local_desc);
+		pr_err("requesting hog GPIO %s (chip %s, offset %d) failed, %d\n",
+		       name, chip->label, hwnum, status);
+		return status;
 	}
 
 	status = gpiod_configure_flags(desc, name, dflags);
 	if (status < 0) {
-		pr_err("setup of hog GPIO %s (chip %s, offset %d) failed\n",
-		       name, chip->label, hwnum);
+		pr_err("setup of hog GPIO %s (chip %s, offset %d) failed, %d\n",
+		       name, chip->label, hwnum, status);
 		gpiochip_free_own_desc(desc);
 		return status;
 	}
diff --git a/drivers/gpio/gpiolib.h b/drivers/gpio/gpiolib.h
index e30e5fd..2d9ea5e 100644
--- a/drivers/gpio/gpiolib.h
+++ b/drivers/gpio/gpiolib.h
@@ -141,6 +141,10 @@
 		   const char *list_name, int index, enum of_gpio_flags *flags);
 
 struct gpio_desc *gpiochip_get_desc(struct gpio_chip *chip, u16 hwnum);
+void gpiod_set_array_value_complex(bool raw, bool can_sleep,
+				   unsigned int array_size,
+				   struct gpio_desc **desc_array,
+				   int *value_array);
 
 extern struct spinlock gpio_lock;
 extern struct list_head gpio_devices;
diff --git a/drivers/input/keyboard/adp5588-keys.c b/drivers/input/keyboard/adp5588-keys.c
index 21a62d0..53fe9a3 100644
--- a/drivers/input/keyboard/adp5588-keys.c
+++ b/drivers/input/keyboard/adp5588-keys.c
@@ -73,7 +73,7 @@
 #ifdef CONFIG_GPIOLIB
 static int adp5588_gpio_get_value(struct gpio_chip *chip, unsigned off)
 {
-	struct adp5588_kpad *kpad = container_of(chip, struct adp5588_kpad, gc);
+	struct adp5588_kpad *kpad = gpiochip_get_data(chip);
 	unsigned int bank = ADP5588_BANK(kpad->gpiomap[off]);
 	unsigned int bit = ADP5588_BIT(kpad->gpiomap[off]);
 	int val;
@@ -93,7 +93,7 @@
 static void adp5588_gpio_set_value(struct gpio_chip *chip,
 				   unsigned off, int val)
 {
-	struct adp5588_kpad *kpad = container_of(chip, struct adp5588_kpad, gc);
+	struct adp5588_kpad *kpad = gpiochip_get_data(chip);
 	unsigned int bank = ADP5588_BANK(kpad->gpiomap[off]);
 	unsigned int bit = ADP5588_BIT(kpad->gpiomap[off]);
 
@@ -112,7 +112,7 @@
 
 static int adp5588_gpio_direction_input(struct gpio_chip *chip, unsigned off)
 {
-	struct adp5588_kpad *kpad = container_of(chip, struct adp5588_kpad, gc);
+	struct adp5588_kpad *kpad = gpiochip_get_data(chip);
 	unsigned int bank = ADP5588_BANK(kpad->gpiomap[off]);
 	unsigned int bit = ADP5588_BIT(kpad->gpiomap[off]);
 	int ret;
@@ -130,7 +130,7 @@
 static int adp5588_gpio_direction_output(struct gpio_chip *chip,
 					 unsigned off, int val)
 {
-	struct adp5588_kpad *kpad = container_of(chip, struct adp5588_kpad, gc);
+	struct adp5588_kpad *kpad = gpiochip_get_data(chip);
 	unsigned int bank = ADP5588_BANK(kpad->gpiomap[off]);
 	unsigned int bit = ADP5588_BIT(kpad->gpiomap[off]);
 	int ret;
@@ -210,7 +210,7 @@
 
 	mutex_init(&kpad->gpio_lock);
 
-	error = gpiochip_add(&kpad->gc);
+	error = gpiochip_add_data(&kpad->gc, kpad);
 	if (error) {
 		dev_err(dev, "gpiochip_add failed, err: %d\n", error);
 		return error;
diff --git a/drivers/input/keyboard/adp5589-keys.c b/drivers/input/keyboard/adp5589-keys.c
index c01a1d6..32d94c6 100644
--- a/drivers/input/keyboard/adp5589-keys.c
+++ b/drivers/input/keyboard/adp5589-keys.c
@@ -387,7 +387,7 @@
 #ifdef CONFIG_GPIOLIB
 static int adp5589_gpio_get_value(struct gpio_chip *chip, unsigned off)
 {
-	struct adp5589_kpad *kpad = container_of(chip, struct adp5589_kpad, gc);
+	struct adp5589_kpad *kpad = gpiochip_get_data(chip);
 	unsigned int bank = kpad->var->bank(kpad->gpiomap[off]);
 	unsigned int bit = kpad->var->bit(kpad->gpiomap[off]);
 
@@ -399,7 +399,7 @@
 static void adp5589_gpio_set_value(struct gpio_chip *chip,
 				   unsigned off, int val)
 {
-	struct adp5589_kpad *kpad = container_of(chip, struct adp5589_kpad, gc);
+	struct adp5589_kpad *kpad = gpiochip_get_data(chip);
 	unsigned int bank = kpad->var->bank(kpad->gpiomap[off]);
 	unsigned int bit = kpad->var->bit(kpad->gpiomap[off]);
 
@@ -418,7 +418,7 @@
 
 static int adp5589_gpio_direction_input(struct gpio_chip *chip, unsigned off)
 {
-	struct adp5589_kpad *kpad = container_of(chip, struct adp5589_kpad, gc);
+	struct adp5589_kpad *kpad = gpiochip_get_data(chip);
 	unsigned int bank = kpad->var->bank(kpad->gpiomap[off]);
 	unsigned int bit = kpad->var->bit(kpad->gpiomap[off]);
 	int ret;
@@ -438,7 +438,7 @@
 static int adp5589_gpio_direction_output(struct gpio_chip *chip,
 					 unsigned off, int val)
 {
-	struct adp5589_kpad *kpad = container_of(chip, struct adp5589_kpad, gc);
+	struct adp5589_kpad *kpad = gpiochip_get_data(chip);
 	unsigned int bank = kpad->var->bank(kpad->gpiomap[off]);
 	unsigned int bit = kpad->var->bit(kpad->gpiomap[off]);
 	int ret;
@@ -525,9 +525,9 @@
 
 	mutex_init(&kpad->gpio_lock);
 
-	error = gpiochip_add(&kpad->gc);
+	error = gpiochip_add_data(&kpad->gc, kpad);
 	if (error) {
-		dev_err(dev, "gpiochip_add failed, err: %d\n", error);
+		dev_err(dev, "gpiochip_add_data() failed, err: %d\n", error);
 		return error;
 	}
 
diff --git a/drivers/input/touchscreen/ad7879.c b/drivers/input/touchscreen/ad7879.c
index 69d299d..e4bf110 100644
--- a/drivers/input/touchscreen/ad7879.c
+++ b/drivers/input/touchscreen/ad7879.c
@@ -379,7 +379,7 @@
 static int ad7879_gpio_direction_input(struct gpio_chip *chip,
 					unsigned gpio)
 {
-	struct ad7879 *ts = container_of(chip, struct ad7879, gc);
+	struct ad7879 *ts = gpiochip_get_data(chip);
 	int err;
 
 	mutex_lock(&ts->mutex);
@@ -393,7 +393,7 @@
 static int ad7879_gpio_direction_output(struct gpio_chip *chip,
 					unsigned gpio, int level)
 {
-	struct ad7879 *ts = container_of(chip, struct ad7879, gc);
+	struct ad7879 *ts = gpiochip_get_data(chip);
 	int err;
 
 	mutex_lock(&ts->mutex);
@@ -412,7 +412,7 @@
 
 static int ad7879_gpio_get_value(struct gpio_chip *chip, unsigned gpio)
 {
-	struct ad7879 *ts = container_of(chip, struct ad7879, gc);
+	struct ad7879 *ts = gpiochip_get_data(chip);
 	u16 val;
 
 	mutex_lock(&ts->mutex);
@@ -425,7 +425,7 @@
 static void ad7879_gpio_set_value(struct gpio_chip *chip,
 				  unsigned gpio, int value)
 {
-	struct ad7879 *ts = container_of(chip, struct ad7879, gc);
+	struct ad7879 *ts = gpiochip_get_data(chip);
 
 	mutex_lock(&ts->mutex);
 	if (value)
@@ -456,7 +456,7 @@
 		ts->gc.owner = THIS_MODULE;
 		ts->gc.parent = ts->dev;
 
-		ret = gpiochip_add(&ts->gc);
+		ret = gpiochip_add_data(&ts->gc, ts);
 		if (ret)
 			dev_err(ts->dev, "failed to register gpio %d\n",
 				ts->gc.base);
diff --git a/drivers/mfd/intel_quark_i2c_gpio.c b/drivers/mfd/intel_quark_i2c_gpio.c
index bdc5e27..a24b35f 100644
--- a/drivers/mfd/intel_quark_i2c_gpio.c
+++ b/drivers/mfd/intel_quark_i2c_gpio.c
@@ -219,8 +219,7 @@
 		return -ENOMEM;
 
 	/* Set the properties for portA */
-	pdata->properties->node		= NULL;
-	pdata->properties->name		= "intel-quark-x1000-gpio-portA";
+	pdata->properties->fwnode	= NULL;
 	pdata->properties->idx		= 0;
 	pdata->properties->ngpio	= INTEL_QUARK_MFD_NGPIO;
 	pdata->properties->gpio_base	= INTEL_QUARK_MFD_GPIO_BASE;
diff --git a/drivers/pinctrl/sh-pfc/gpio.c b/drivers/pinctrl/sh-pfc/gpio.c
index a6681b8..97dff6a 100644
--- a/drivers/pinctrl/sh-pfc/gpio.c
+++ b/drivers/pinctrl/sh-pfc/gpio.c
@@ -212,7 +212,7 @@
 		}
 	}
 
-	return -ENOSYS;
+	return 0;
 
 found:
 	return pfc->irqs[i];
diff --git a/drivers/platform/x86/intel_pmic_gpio.c b/drivers/platform/x86/intel_pmic_gpio.c
index 0e73fd1..63b371d 100644
--- a/drivers/platform/x86/intel_pmic_gpio.c
+++ b/drivers/platform/x86/intel_pmic_gpio.c
@@ -30,7 +30,7 @@
 #include <linux/ioport.h>
 #include <linux/init.h>
 #include <linux/io.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <asm/intel_scu_ipc.h>
 #include <linux/device.h>
 #include <linux/intel_pmic_gpio.h>
@@ -174,7 +174,7 @@
 
 static int pmic_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
 {
-	struct pmic_gpio *pg = container_of(chip, struct pmic_gpio, chip);
+	struct pmic_gpio *pg = gpiochip_get_data(chip);
 
 	return pg->irq_base + offset;
 }
@@ -279,7 +279,7 @@
 	mutex_init(&pg->buslock);
 
 	pg->chip.parent = dev;
-	retval = gpiochip_add(&pg->chip);
+	retval = gpiochip_add_data(&pg->chip, pg);
 	if (retval) {
 		pr_err("Can not add pmic gpio chip\n");
 		goto err;
diff --git a/drivers/soc/fsl/qe/gpio.c b/drivers/soc/fsl/qe/gpio.c
index 6584571..333eb22 100644
--- a/drivers/soc/fsl/qe/gpio.c
+++ b/drivers/soc/fsl/qe/gpio.c
@@ -18,6 +18,8 @@
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/of_gpio.h>
+#include <linux/gpio/driver.h>
+/* FIXME: needed for gpio_to_chip() get rid of this */
 #include <linux/gpio.h>
 #include <linux/slab.h>
 #include <linux/export.h>
@@ -37,15 +39,9 @@
 	struct qe_pio_regs saved_regs;
 };
 
-static inline struct qe_gpio_chip *
-to_qe_gpio_chip(struct of_mm_gpio_chip *mm_gc)
-{
-	return container_of(mm_gc, struct qe_gpio_chip, mm_gc);
-}
-
 static void qe_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
 {
-	struct qe_gpio_chip *qe_gc = to_qe_gpio_chip(mm_gc);
+	struct qe_gpio_chip *qe_gc = gpiochip_get_data(&mm_gc->gc);
 	struct qe_pio_regs __iomem *regs = mm_gc->regs;
 
 	qe_gc->cpdata = in_be32(&regs->cpdata);
@@ -69,7 +65,7 @@
 static void qe_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct qe_gpio_chip *qe_gc = to_qe_gpio_chip(mm_gc);
+	struct qe_gpio_chip *qe_gc = gpiochip_get_data(gc);
 	struct qe_pio_regs __iomem *regs = mm_gc->regs;
 	unsigned long flags;
 	u32 pin_mask = 1 << (QE_PIO_PINS - 1 - gpio);
@@ -89,7 +85,7 @@
 static int qe_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct qe_gpio_chip *qe_gc = to_qe_gpio_chip(mm_gc);
+	struct qe_gpio_chip *qe_gc = gpiochip_get_data(gc);
 	unsigned long flags;
 
 	spin_lock_irqsave(&qe_gc->lock, flags);
@@ -104,7 +100,7 @@
 static int qe_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
 {
 	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
-	struct qe_gpio_chip *qe_gc = to_qe_gpio_chip(mm_gc);
+	struct qe_gpio_chip *qe_gc = gpiochip_get_data(gc);
 	unsigned long flags;
 
 	qe_gpio_set(gc, gpio, val);
@@ -165,7 +161,7 @@
 	}
 
 	mm_gc = to_of_mm_gpio_chip(gc);
-	qe_gc = to_qe_gpio_chip(mm_gc);
+	qe_gc = gpiochip_get_data(gc);
 
 	spin_lock_irqsave(&qe_gc->lock, flags);
 
@@ -302,7 +298,7 @@
 		gc->get = qe_gpio_get;
 		gc->set = qe_gpio_set;
 
-		ret = of_mm_gpiochip_add(np, mm_gc);
+		ret = of_mm_gpiochip_add_data(np, mm_gc, qe_gc);
 		if (ret)
 			goto err;
 		continue;
diff --git a/drivers/ssb/driver_gpio.c b/drivers/ssb/driver_gpio.c
index f92e266..180e027 100644
--- a/drivers/ssb/driver_gpio.c
+++ b/drivers/ssb/driver_gpio.c
@@ -8,7 +8,7 @@
  * Licensed under the GNU/GPL. See COPYING for details.
  */
 
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/irq.h>
 #include <linux/interrupt.h>
 #include <linux/irqdomain.h>
@@ -22,15 +22,10 @@
  * Shared
  **************************************************/
 
-static struct ssb_bus *ssb_gpio_get_bus(struct gpio_chip *chip)
-{
-	return container_of(chip, struct ssb_bus, gpio);
-}
-
 #if IS_ENABLED(CONFIG_SSB_EMBEDDED)
 static int ssb_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
 {
-	struct ssb_bus *bus = ssb_gpio_get_bus(chip);
+	struct ssb_bus *bus = gpiochip_get_data(chip);
 
 	if (bus->bustype == SSB_BUSTYPE_SSB)
 		return irq_find_mapping(bus->irq_domain, gpio);
@@ -45,7 +40,7 @@
 
 static int ssb_gpio_chipco_get_value(struct gpio_chip *chip, unsigned gpio)
 {
-	struct ssb_bus *bus = ssb_gpio_get_bus(chip);
+	struct ssb_bus *bus = gpiochip_get_data(chip);
 
 	return !!ssb_chipco_gpio_in(&bus->chipco, 1 << gpio);
 }
@@ -53,7 +48,7 @@
 static void ssb_gpio_chipco_set_value(struct gpio_chip *chip, unsigned gpio,
 				      int value)
 {
-	struct ssb_bus *bus = ssb_gpio_get_bus(chip);
+	struct ssb_bus *bus = gpiochip_get_data(chip);
 
 	ssb_chipco_gpio_out(&bus->chipco, 1 << gpio, value ? 1 << gpio : 0);
 }
@@ -61,7 +56,7 @@
 static int ssb_gpio_chipco_direction_input(struct gpio_chip *chip,
 					   unsigned gpio)
 {
-	struct ssb_bus *bus = ssb_gpio_get_bus(chip);
+	struct ssb_bus *bus = gpiochip_get_data(chip);
 
 	ssb_chipco_gpio_outen(&bus->chipco, 1 << gpio, 0);
 	return 0;
@@ -70,7 +65,7 @@
 static int ssb_gpio_chipco_direction_output(struct gpio_chip *chip,
 					    unsigned gpio, int value)
 {
-	struct ssb_bus *bus = ssb_gpio_get_bus(chip);
+	struct ssb_bus *bus = gpiochip_get_data(chip);
 
 	ssb_chipco_gpio_outen(&bus->chipco, 1 << gpio, 1 << gpio);
 	ssb_chipco_gpio_out(&bus->chipco, 1 << gpio, value ? 1 << gpio : 0);
@@ -79,7 +74,7 @@
 
 static int ssb_gpio_chipco_request(struct gpio_chip *chip, unsigned gpio)
 {
-	struct ssb_bus *bus = ssb_gpio_get_bus(chip);
+	struct ssb_bus *bus = gpiochip_get_data(chip);
 
 	ssb_chipco_gpio_control(&bus->chipco, 1 << gpio, 0);
 	/* clear pulldown */
@@ -92,7 +87,7 @@
 
 static void ssb_gpio_chipco_free(struct gpio_chip *chip, unsigned gpio)
 {
-	struct ssb_bus *bus = ssb_gpio_get_bus(chip);
+	struct ssb_bus *bus = gpiochip_get_data(chip);
 
 	/* clear pullup */
 	ssb_chipco_gpio_pullup(&bus->chipco, 1 << gpio, 0);
@@ -246,7 +241,7 @@
 	if (err)
 		return err;
 
-	err = gpiochip_add(chip);
+	err = gpiochip_add_data(chip, bus);
 	if (err) {
 		ssb_gpio_irq_chipco_domain_exit(bus);
 		return err;
@@ -263,7 +258,7 @@
 
 static int ssb_gpio_extif_get_value(struct gpio_chip *chip, unsigned gpio)
 {
-	struct ssb_bus *bus = ssb_gpio_get_bus(chip);
+	struct ssb_bus *bus = gpiochip_get_data(chip);
 
 	return !!ssb_extif_gpio_in(&bus->extif, 1 << gpio);
 }
@@ -271,7 +266,7 @@
 static void ssb_gpio_extif_set_value(struct gpio_chip *chip, unsigned gpio,
 				     int value)
 {
-	struct ssb_bus *bus = ssb_gpio_get_bus(chip);
+	struct ssb_bus *bus = gpiochip_get_data(chip);
 
 	ssb_extif_gpio_out(&bus->extif, 1 << gpio, value ? 1 << gpio : 0);
 }
@@ -279,7 +274,7 @@
 static int ssb_gpio_extif_direction_input(struct gpio_chip *chip,
 					  unsigned gpio)
 {
-	struct ssb_bus *bus = ssb_gpio_get_bus(chip);
+	struct ssb_bus *bus = gpiochip_get_data(chip);
 
 	ssb_extif_gpio_outen(&bus->extif, 1 << gpio, 0);
 	return 0;
@@ -288,7 +283,7 @@
 static int ssb_gpio_extif_direction_output(struct gpio_chip *chip,
 					   unsigned gpio, int value)
 {
-	struct ssb_bus *bus = ssb_gpio_get_bus(chip);
+	struct ssb_bus *bus = gpiochip_get_data(chip);
 
 	ssb_extif_gpio_outen(&bus->extif, 1 << gpio, 1 << gpio);
 	ssb_extif_gpio_out(&bus->extif, 1 << gpio, value ? 1 << gpio : 0);
@@ -439,7 +434,7 @@
 	if (err)
 		return err;
 
-	err = gpiochip_add(chip);
+	err = gpiochip_add_data(chip, bus);
 	if (err) {
 		ssb_gpio_irq_extif_domain_exit(bus);
 		return err;
diff --git a/drivers/staging/vme/devices/vme_pio2_gpio.c b/drivers/staging/vme/devices/vme_pio2_gpio.c
index df992c3..6d361201 100644
--- a/drivers/staging/vme/devices/vme_pio2_gpio.c
+++ b/drivers/staging/vme/devices/vme_pio2_gpio.c
@@ -17,7 +17,7 @@
 #include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/ctype.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/slab.h>
 #include <linux/vme.h>
 
@@ -25,16 +25,11 @@
 
 static const char driver_name[] = "pio2_gpio";
 
-static struct pio2_card *gpio_to_pio2_card(struct gpio_chip *chip)
-{
-	return container_of(chip, struct pio2_card, gc);
-}
-
 static int pio2_gpio_get(struct gpio_chip *chip, unsigned int offset)
 {
 	u8 reg;
 	int retval;
-	struct pio2_card *card = gpio_to_pio2_card(chip);
+	struct pio2_card *card = gpiochip_get_data(chip);
 
 	if ((card->bank[PIO2_CHANNEL_BANK[offset]].config == OUTPUT) |
 	    (card->bank[PIO2_CHANNEL_BANK[offset]].config == NOFIT)) {
@@ -71,7 +66,7 @@
 {
 	u8 reg;
 	int retval;
-	struct pio2_card *card = gpio_to_pio2_card(chip);
+	struct pio2_card *card = gpiochip_get_data(chip);
 
 	if ((card->bank[PIO2_CHANNEL_BANK[offset]].config == INPUT) |
 	    (card->bank[PIO2_CHANNEL_BANK[offset]].config == NOFIT)) {
@@ -100,7 +95,7 @@
 static int pio2_gpio_dir_in(struct gpio_chip *chip, unsigned offset)
 {
 	int data;
-	struct pio2_card *card = gpio_to_pio2_card(chip);
+	struct pio2_card *card = gpiochip_get_data(chip);
 
 	if ((card->bank[PIO2_CHANNEL_BANK[offset]].config == OUTPUT) |
 	    (card->bank[PIO2_CHANNEL_BANK[offset]].config == NOFIT)) {
@@ -119,7 +114,7 @@
 static int pio2_gpio_dir_out(struct gpio_chip *chip, unsigned offset, int value)
 {
 	int data;
-	struct pio2_card *card = gpio_to_pio2_card(chip);
+	struct pio2_card *card = gpiochip_get_data(chip);
 
 	if ((card->bank[PIO2_CHANNEL_BANK[offset]].config == INPUT) |
 	    (card->bank[PIO2_CHANNEL_BANK[offset]].config == NOFIT)) {
@@ -205,7 +200,7 @@
 	card->gc.set = pio2_gpio_set;
 
 	/* This function adds a memory mapped GPIO chip */
-	retval = gpiochip_add(&card->gc);
+	retval = gpiochip_add_data(&card->gc, card);
 	if (retval) {
 		dev_err(&card->vdev->dev, "Unable to register GPIO\n");
 		kfree(card->gc.label);
diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c
index 3f98165..3f6e0ab 100644
--- a/drivers/tty/serial/max310x.c
+++ b/drivers/tty/serial/max310x.c
@@ -17,7 +17,7 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/device.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
@@ -1036,7 +1036,7 @@
 static int max310x_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
 	unsigned int val;
-	struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
+	struct max310x_port *s = gpiochip_get_data(chip);
 	struct uart_port *port = &s->p[offset / 4].port;
 
 	val = max310x_port_read(port, MAX310X_GPIODATA_REG);
@@ -1046,7 +1046,7 @@
 
 static void max310x_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 {
-	struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
+	struct max310x_port *s = gpiochip_get_data(chip);
 	struct uart_port *port = &s->p[offset / 4].port;
 
 	max310x_port_update(port, MAX310X_GPIODATA_REG, 1 << (offset % 4),
@@ -1055,7 +1055,7 @@
 
 static int max310x_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
 {
-	struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
+	struct max310x_port *s = gpiochip_get_data(chip);
 	struct uart_port *port = &s->p[offset / 4].port;
 
 	max310x_port_update(port, MAX310X_GPIOCFG_REG, 1 << (offset % 4), 0);
@@ -1066,7 +1066,7 @@
 static int max310x_gpio_direction_output(struct gpio_chip *chip,
 					 unsigned offset, int value)
 {
-	struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
+	struct max310x_port *s = gpiochip_get_data(chip);
 	struct uart_port *port = &s->p[offset / 4].port;
 
 	max310x_port_update(port, MAX310X_GPIODATA_REG, 1 << (offset % 4),
@@ -1183,7 +1183,7 @@
 	s->gpio.base		= -1;
 	s->gpio.ngpio		= devtype->nr * 4;
 	s->gpio.can_sleep	= 1;
-	ret = gpiochip_add(&s->gpio);
+	ret = gpiochip_add_data(&s->gpio, s);
 	if (ret)
 		goto out_uart;
 #endif
diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index 025a426..e639361 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -17,7 +17,7 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/device.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/i2c.h>
 #include <linux/module.h>
 #include <linux/of.h>
@@ -1104,8 +1104,7 @@
 static int sc16is7xx_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
 	unsigned int val;
-	struct sc16is7xx_port *s = container_of(chip, struct sc16is7xx_port,
-						gpio);
+	struct sc16is7xx_port *s = gpiochip_get_data(chip);
 	struct uart_port *port = &s->p[0].port;
 
 	val = sc16is7xx_port_read(port, SC16IS7XX_IOSTATE_REG);
@@ -1115,8 +1114,7 @@
 
 static void sc16is7xx_gpio_set(struct gpio_chip *chip, unsigned offset, int val)
 {
-	struct sc16is7xx_port *s = container_of(chip, struct sc16is7xx_port,
-						gpio);
+	struct sc16is7xx_port *s = gpiochip_get_data(chip);
 	struct uart_port *port = &s->p[0].port;
 
 	sc16is7xx_port_update(port, SC16IS7XX_IOSTATE_REG, BIT(offset),
@@ -1126,8 +1124,7 @@
 static int sc16is7xx_gpio_direction_input(struct gpio_chip *chip,
 					  unsigned offset)
 {
-	struct sc16is7xx_port *s = container_of(chip, struct sc16is7xx_port,
-						gpio);
+	struct sc16is7xx_port *s = gpiochip_get_data(chip);
 	struct uart_port *port = &s->p[0].port;
 
 	sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset), 0);
@@ -1138,8 +1135,7 @@
 static int sc16is7xx_gpio_direction_output(struct gpio_chip *chip,
 					   unsigned offset, int val)
 {
-	struct sc16is7xx_port *s = container_of(chip, struct sc16is7xx_port,
-						gpio);
+	struct sc16is7xx_port *s = gpiochip_get_data(chip);
 	struct uart_port *port = &s->p[0].port;
 
 	sc16is7xx_port_update(port, SC16IS7XX_IOSTATE_REG, BIT(offset),
@@ -1210,7 +1206,7 @@
 		s->gpio.base		 = -1;
 		s->gpio.ngpio		 = devtype->nr_gpio;
 		s->gpio.can_sleep	 = 1;
-		ret = gpiochip_add(&s->gpio);
+		ret = gpiochip_add_data(&s->gpio, s);
 		if (ret)
 			goto out_thread;
 	}
diff --git a/include/linux/gpio/driver.h b/include/linux/gpio/driver.h
index bee976f..50882e0 100644
--- a/include/linux/gpio/driver.h
+++ b/include/linux/gpio/driver.h
@@ -20,6 +20,18 @@
 #ifdef CONFIG_GPIOLIB
 
 /**
+ * enum single_ended_mode - mode for single ended operation
+ * @LINE_MODE_PUSH_PULL: normal mode for a GPIO line, drive actively high/low
+ * @LINE_MODE_OPEN_DRAIN: set line to be open drain
+ * @LINE_MODE_OPEN_SOURCE: set line to be open source
+ */
+enum single_ended_mode {
+	LINE_MODE_PUSH_PULL,
+	LINE_MODE_OPEN_DRAIN,
+	LINE_MODE_OPEN_SOURCE,
+};
+
+/**
  * struct gpio_chip - abstract a GPIO controller
  * @label: a functional name for the GPIO device, such as a part
  *	number or the name of the SoC IP-block implementing it.
@@ -38,7 +50,15 @@
  * @set: assigns output value for signal "offset"
  * @set_multiple: assigns output values for multiple signals defined by "mask"
  * @set_debounce: optional hook for setting debounce time for specified gpio in
- *      interrupt triggered gpio chips
+ *	interrupt triggered gpio chips
+ * @set_single_ended: optional hook for setting a line as open drain, open
+ *	source, or non-single ended (restore from open drain/source to normal
+ *	push-pull mode) this should be implemented if the hardware supports
+ *	open drain or open source settings. The GPIOlib will otherwise try
+ *	to emulate open drain/source by not actively driving lines high/low
+ *	if a consumer request this. The driver may return -ENOTSUPP if e.g.
+ *	it supports just open drain but not open source and is called
+ *	with LINE_MODE_OPEN_SOURCE as mode argument.
  * @to_irq: optional hook supporting non-static gpio_to_irq() mappings;
  *	implementation may not sleep
  * @dbg_show: optional routine to show contents in debugfs; default code
@@ -130,6 +150,9 @@
 	int			(*set_debounce)(struct gpio_chip *chip,
 						unsigned offset,
 						unsigned debounce);
+	int			(*set_single_ended)(struct gpio_chip *chip,
+						unsigned offset,
+						enum single_ended_mode mode);
 
 	int			(*to_irq)(struct gpio_chip *chip,
 						unsigned offset);
diff --git a/include/linux/i2c/sx150x.h b/include/linux/i2c/sx150x.h
deleted file mode 100644
index 52baa79..0000000
--- a/include/linux/i2c/sx150x.h
+++ /dev/null
@@ -1,82 +0,0 @@
-/*
- * Driver for the Semtech SX150x I2C GPIO Expanders
- *
- * Copyright (c) 2010, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
- */
-#ifndef __LINUX_I2C_SX150X_H
-#define __LINUX_I2C_SX150X_H
-
-/**
- * struct sx150x_platform_data - config data for SX150x driver
- * @gpio_base: The index number of the first GPIO assigned to this
- *             GPIO expander.  The expander will create a block of
- *             consecutively numbered gpios beginning at the given base,
- *             with the size of the block depending on the model of the
- *             expander chip.
- * @oscio_is_gpo: If set to true, the driver will configure OSCIO as a GPO
- *                instead of as an oscillator, increasing the size of the
- *                GP(I)O pool created by this expander by one.  The
- *                output-only GPO pin will be added at the end of the block.
- * @io_pullup_ena: A bit-mask which enables or disables the pull-up resistor
- *                 for each IO line in the expander.  Setting the bit at
- *                 position n will enable the pull-up for the IO at
- *                 the corresponding offset.  For chips with fewer than
- *                 16 IO pins, high-end bits are ignored.
- * @io_pulldn_ena: A bit-mask which enables-or disables the pull-down
- *                 resistor for each IO line in the expander. Setting the
- *                 bit at position n will enable the pull-down for the IO at
- *                 the corresponding offset.  For chips with fewer than
- *                 16 IO pins, high-end bits are ignored.
- * @io_open_drain_ena: A bit-mask which enables-or disables open-drain
- *                     operation for each IO line in the expander. Setting the
- *                     bit at position n enables open-drain operation for
- *                     the IO at the corresponding offset.  Clearing the bit
- *                     enables regular push-pull operation for that IO.
- *                     For chips with fewer than 16 IO pins, high-end bits
- *                     are ignored.
- * @io_polarity: A bit-mask which enables polarity inversion for each IO line
- *               in the expander.  Setting the bit at position n inverts
- *               the polarity of that IO line, while clearing it results
- *               in normal polarity. For chips with fewer than 16 IO pins,
- *               high-end bits are ignored.
- * @irq_summary: The 'summary IRQ' line to which the GPIO expander's INT line
- *               is connected, via which it reports interrupt events
- *               across all GPIO lines.  This must be a real,
- *               pre-existing IRQ line.
- *               Setting this value < 0 disables the irq_chip functionality
- *               of the driver.
- * @irq_base: The first 'virtual IRQ' line at which our block of GPIO-based
- *            IRQ lines will appear.  Similarly to gpio_base, the expander
- *            will create a block of irqs beginning at this number.
- *            This value is ignored if irq_summary is < 0.
- * @reset_during_probe: If set to true, the driver will trigger a full
- *                      reset of the chip at the beginning of the probe
- *                      in order to place it in a known state.
- */
-struct sx150x_platform_data {
-	unsigned gpio_base;
-	bool     oscio_is_gpo;
-	u16      io_pullup_ena;
-	u16      io_pulldn_ena;
-	u16      io_open_drain_ena;
-	u16      io_polarity;
-	int      irq_summary;
-	unsigned irq_base;
-	bool     reset_during_probe;
-};
-
-#endif /* __LINUX_I2C_SX150X_H */
diff --git a/include/linux/platform_data/gpio-dwapb.h b/include/linux/platform_data/gpio-dwapb.h
index 28702c8..2dc7f4a 100644
--- a/include/linux/platform_data/gpio-dwapb.h
+++ b/include/linux/platform_data/gpio-dwapb.h
@@ -15,8 +15,7 @@
 #define GPIO_DW_APB_H
 
 struct dwapb_port_property {
-	struct device_node *node;
-	const char	*name;
+	struct fwnode_handle *fwnode;
 	unsigned int	idx;
 	unsigned int	ngpio;
 	unsigned int	gpio_base;
diff --git a/kernel/irq/irqdomain.c b/kernel/irq/irqdomain.c
index 503c5b9..d65f6f3 100644
--- a/kernel/irq/irqdomain.c
+++ b/kernel/irq/irqdomain.c
@@ -1100,6 +1100,7 @@
 	}
 	irq_domain_free_irqs_parent(domain, virq, nr_irqs);
 }
+EXPORT_SYMBOL_GPL(irq_domain_free_irqs_common);
 
 /**
  * irq_domain_free_irqs_top - Clear handler and handler data, clear irqdata and free parent
diff --git a/sound/soc/codecs/rt5677.c b/sound/soc/codecs/rt5677.c
index 33e290b..6021226 100644
--- a/sound/soc/codecs/rt5677.c
+++ b/sound/soc/codecs/rt5677.c
@@ -4520,14 +4520,9 @@
 }
 
 #ifdef CONFIG_GPIOLIB
-static inline struct rt5677_priv *gpio_to_rt5677(struct gpio_chip *chip)
-{
-	return container_of(chip, struct rt5677_priv, gpio_chip);
-}
-
 static void rt5677_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 {
-	struct rt5677_priv *rt5677 = gpio_to_rt5677(chip);
+	struct rt5677_priv *rt5677 = gpiochip_get_data(chip);
 
 	switch (offset) {
 	case RT5677_GPIO1 ... RT5677_GPIO5:
@@ -4548,7 +4543,7 @@
 static int rt5677_gpio_direction_out(struct gpio_chip *chip,
 				     unsigned offset, int value)
 {
-	struct rt5677_priv *rt5677 = gpio_to_rt5677(chip);
+	struct rt5677_priv *rt5677 = gpiochip_get_data(chip);
 
 	switch (offset) {
 	case RT5677_GPIO1 ... RT5677_GPIO5:
@@ -4572,7 +4567,7 @@
 
 static int rt5677_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
-	struct rt5677_priv *rt5677 = gpio_to_rt5677(chip);
+	struct rt5677_priv *rt5677 = gpiochip_get_data(chip);
 	int value, ret;
 
 	ret = regmap_read(rt5677->regmap, RT5677_GPIO_ST, &value);
@@ -4584,7 +4579,7 @@
 
 static int rt5677_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
 {
-	struct rt5677_priv *rt5677 = gpio_to_rt5677(chip);
+	struct rt5677_priv *rt5677 = gpiochip_get_data(chip);
 
 	switch (offset) {
 	case RT5677_GPIO1 ... RT5677_GPIO5:
@@ -4638,7 +4633,7 @@
 
 static int rt5677_to_irq(struct gpio_chip *chip, unsigned offset)
 {
-	struct rt5677_priv *rt5677 = gpio_to_rt5677(chip);
+	struct rt5677_priv *rt5677 = gpiochip_get_data(chip);
 	struct regmap_irq_chip_data *data = rt5677->irq_data;
 	int irq;
 
@@ -4697,7 +4692,7 @@
 	rt5677->gpio_chip.parent = &i2c->dev;
 	rt5677->gpio_chip.base = -1;
 
-	ret = gpiochip_add(&rt5677->gpio_chip);
+	ret = gpiochip_add_data(&rt5677->gpio_chip, rt5677);
 	if (ret != 0)
 		dev_err(&i2c->dev, "Failed to add GPIOs: %d\n", ret);
 }
diff --git a/sound/soc/codecs/wm5100.c b/sound/soc/codecs/wm5100.c
index 171a23d..512a9d2 100644
--- a/sound/soc/codecs/wm5100.c
+++ b/sound/soc/codecs/wm5100.c
@@ -17,6 +17,7 @@
 #include <linux/export.h>
 #include <linux/pm.h>
 #include <linux/gcd.h>
+#include <linux/gpio/driver.h>
 #include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/pm_runtime.h>
@@ -2236,14 +2237,9 @@
 }
 
 #ifdef CONFIG_GPIOLIB
-static inline struct wm5100_priv *gpio_to_wm5100(struct gpio_chip *chip)
-{
-	return container_of(chip, struct wm5100_priv, gpio_chip);
-}
-
 static void wm5100_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 {
-	struct wm5100_priv *wm5100 = gpio_to_wm5100(chip);
+	struct wm5100_priv *wm5100 = gpiochip_get_data(chip);
 
 	regmap_update_bits(wm5100->regmap, WM5100_GPIO_CTRL_1 + offset,
 			   WM5100_GP1_LVL, !!value << WM5100_GP1_LVL_SHIFT);
@@ -2252,7 +2248,7 @@
 static int wm5100_gpio_direction_out(struct gpio_chip *chip,
 				     unsigned offset, int value)
 {
-	struct wm5100_priv *wm5100 = gpio_to_wm5100(chip);
+	struct wm5100_priv *wm5100 = gpiochip_get_data(chip);
 	int val, ret;
 
 	val = (1 << WM5100_GP1_FN_SHIFT) | (!!value << WM5100_GP1_LVL_SHIFT);
@@ -2268,7 +2264,7 @@
 
 static int wm5100_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
-	struct wm5100_priv *wm5100 = gpio_to_wm5100(chip);
+	struct wm5100_priv *wm5100 = gpiochip_get_data(chip);
 	unsigned int reg;
 	int ret;
 
@@ -2281,7 +2277,7 @@
 
 static int wm5100_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
 {
-	struct wm5100_priv *wm5100 = gpio_to_wm5100(chip);
+	struct wm5100_priv *wm5100 = gpiochip_get_data(chip);
 
 	return regmap_update_bits(wm5100->regmap, WM5100_GPIO_CTRL_1 + offset,
 				  WM5100_GP1_FN_MASK | WM5100_GP1_DIR,
@@ -2313,7 +2309,7 @@
 	else
 		wm5100->gpio_chip.base = -1;
 
-	ret = gpiochip_add(&wm5100->gpio_chip);
+	ret = gpiochip_add_data(&wm5100->gpio_chip, wm5100);
 	if (ret != 0)
 		dev_err(&i2c->dev, "Failed to add GPIOs: %d\n", ret);
 }
diff --git a/sound/soc/codecs/wm8903.c b/sound/soc/codecs/wm8903.c
index a82b8bc..a26ca49 100644
--- a/sound/soc/codecs/wm8903.c
+++ b/sound/soc/codecs/wm8903.c
@@ -20,7 +20,7 @@
 #include <linux/init.h>
 #include <linux/completion.h>
 #include <linux/delay.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/pm.h>
 #include <linux/i2c.h>
 #include <linux/regmap.h>
@@ -1766,11 +1766,6 @@
 }
 
 #ifdef CONFIG_GPIOLIB
-static inline struct wm8903_priv *gpio_to_wm8903(struct gpio_chip *chip)
-{
-	return container_of(chip, struct wm8903_priv, gpio_chip);
-}
-
 static int wm8903_gpio_request(struct gpio_chip *chip, unsigned offset)
 {
 	if (offset >= WM8903_NUM_GPIO)
@@ -1781,7 +1776,7 @@
 
 static int wm8903_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
 {
-	struct wm8903_priv *wm8903 = gpio_to_wm8903(chip);
+	struct wm8903_priv *wm8903 = gpiochip_get_data(chip);
 	unsigned int mask, val;
 	int ret;
 
@@ -1799,7 +1794,7 @@
 
 static int wm8903_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
-	struct wm8903_priv *wm8903 = gpio_to_wm8903(chip);
+	struct wm8903_priv *wm8903 = gpiochip_get_data(chip);
 	unsigned int reg;
 
 	regmap_read(wm8903->regmap, WM8903_GPIO_CONTROL_1 + offset, &reg);
@@ -1810,7 +1805,7 @@
 static int wm8903_gpio_direction_out(struct gpio_chip *chip,
 				     unsigned offset, int value)
 {
-	struct wm8903_priv *wm8903 = gpio_to_wm8903(chip);
+	struct wm8903_priv *wm8903 = gpiochip_get_data(chip);
 	unsigned int mask, val;
 	int ret;
 
@@ -1828,7 +1823,7 @@
 
 static void wm8903_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 {
-	struct wm8903_priv *wm8903 = gpio_to_wm8903(chip);
+	struct wm8903_priv *wm8903 = gpiochip_get_data(chip);
 
 	regmap_update_bits(wm8903->regmap, WM8903_GPIO_CONTROL_1 + offset,
 			   WM8903_GP1_LVL_MASK,
@@ -1860,7 +1855,7 @@
 	else
 		wm8903->gpio_chip.base = -1;
 
-	ret = gpiochip_add(&wm8903->gpio_chip);
+	ret = gpiochip_add_data(&wm8903->gpio_chip, wm8903);
 	if (ret != 0)
 		dev_err(wm8903->dev, "Failed to add GPIOs: %d\n", ret);
 }
diff --git a/sound/soc/codecs/wm8962.c b/sound/soc/codecs/wm8962.c
index 720a14e..fc164d6 100644
--- a/sound/soc/codecs/wm8962.c
+++ b/sound/soc/codecs/wm8962.c
@@ -18,7 +18,7 @@
 #include <linux/delay.h>
 #include <linux/pm.h>
 #include <linux/gcd.h>
-#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
 #include <linux/pm_runtime.h>
@@ -3307,14 +3307,9 @@
 }
 
 #ifdef CONFIG_GPIOLIB
-static inline struct wm8962_priv *gpio_to_wm8962(struct gpio_chip *chip)
-{
-	return container_of(chip, struct wm8962_priv, gpio_chip);
-}
-
 static int wm8962_gpio_request(struct gpio_chip *chip, unsigned offset)
 {
-	struct wm8962_priv *wm8962 = gpio_to_wm8962(chip);
+	struct wm8962_priv *wm8962 = gpiochip_get_data(chip);
 
 	/* The WM8962 GPIOs aren't linearly numbered.  For simplicity
 	 * we export linear numbers and error out if the unsupported
@@ -3337,7 +3332,7 @@
 
 static void wm8962_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 {
-	struct wm8962_priv *wm8962 = gpio_to_wm8962(chip);
+	struct wm8962_priv *wm8962 = gpiochip_get_data(chip);
 	struct snd_soc_codec *codec = wm8962->codec;
 
 	snd_soc_update_bits(codec, WM8962_GPIO_BASE + offset,
@@ -3347,7 +3342,7 @@
 static int wm8962_gpio_direction_out(struct gpio_chip *chip,
 				     unsigned offset, int value)
 {
-	struct wm8962_priv *wm8962 = gpio_to_wm8962(chip);
+	struct wm8962_priv *wm8962 = gpiochip_get_data(chip);
 	struct snd_soc_codec *codec = wm8962->codec;
 	int ret, val;
 
@@ -3386,7 +3381,7 @@
 	else
 		wm8962->gpio_chip.base = -1;
 
-	ret = gpiochip_add(&wm8962->gpio_chip);
+	ret = gpiochip_add_data(&wm8962->gpio_chip, wm8962);
 	if (ret != 0)
 		dev_err(codec->dev, "Failed to add GPIOs: %d\n", ret);
 }
diff --git a/sound/soc/codecs/wm8996.c b/sound/soc/codecs/wm8996.c
index f99b34f..a730442 100644
--- a/sound/soc/codecs/wm8996.c
+++ b/sound/soc/codecs/wm8996.c
@@ -17,6 +17,7 @@
 #include <linux/delay.h>
 #include <linux/pm.h>
 #include <linux/gcd.h>
+#include <linux/gpio/driver.h>
 #include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/regmap.h>
@@ -2139,14 +2140,9 @@
 }
 
 #ifdef CONFIG_GPIOLIB
-static inline struct wm8996_priv *gpio_to_wm8996(struct gpio_chip *chip)
-{
-	return container_of(chip, struct wm8996_priv, gpio_chip);
-}
-
 static void wm8996_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 {
-	struct wm8996_priv *wm8996 = gpio_to_wm8996(chip);
+	struct wm8996_priv *wm8996 = gpiochip_get_data(chip);
 
 	regmap_update_bits(wm8996->regmap, WM8996_GPIO_1 + offset,
 			   WM8996_GP1_LVL, !!value << WM8996_GP1_LVL_SHIFT);
@@ -2155,7 +2151,7 @@
 static int wm8996_gpio_direction_out(struct gpio_chip *chip,
 				     unsigned offset, int value)
 {
-	struct wm8996_priv *wm8996 = gpio_to_wm8996(chip);
+	struct wm8996_priv *wm8996 = gpiochip_get_data(chip);
 	int val;
 
 	val = (1 << WM8996_GP1_FN_SHIFT) | (!!value << WM8996_GP1_LVL_SHIFT);
@@ -2167,7 +2163,7 @@
 
 static int wm8996_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
-	struct wm8996_priv *wm8996 = gpio_to_wm8996(chip);
+	struct wm8996_priv *wm8996 = gpiochip_get_data(chip);
 	unsigned int reg;
 	int ret;
 
@@ -2180,7 +2176,7 @@
 
 static int wm8996_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
 {
-	struct wm8996_priv *wm8996 = gpio_to_wm8996(chip);
+	struct wm8996_priv *wm8996 = gpiochip_get_data(chip);
 
 	return regmap_update_bits(wm8996->regmap, WM8996_GPIO_1 + offset,
 				  WM8996_GP1_FN_MASK | WM8996_GP1_DIR,
@@ -2211,7 +2207,7 @@
 	else
 		wm8996->gpio_chip.base = -1;
 
-	ret = gpiochip_add(&wm8996->gpio_chip);
+	ret = gpiochip_add_data(&wm8996->gpio_chip, wm8996);
 	if (ret != 0)
 		dev_err(wm8996->dev, "Failed to add GPIOs: %d\n", ret);
 }
diff --git a/sound/soc/soc-ac97.c b/sound/soc/soc-ac97.c
index 7e0acd8..bc4a55b 100644
--- a/sound/soc/soc-ac97.c
+++ b/sound/soc/soc-ac97.c
@@ -59,8 +59,7 @@
 #ifdef CONFIG_GPIOLIB
 static inline struct snd_soc_codec *gpio_to_codec(struct gpio_chip *chip)
 {
-	struct snd_ac97_gpio_priv *gpio_priv =
-		container_of(chip, struct snd_ac97_gpio_priv, gpio_chip);
+	struct snd_ac97_gpio_priv *gpio_priv = gpiochip_get_data(chip);
 
 	return gpio_priv->codec;
 }
@@ -98,8 +97,7 @@
 static void snd_soc_ac97_gpio_set(struct gpio_chip *chip, unsigned offset,
 				  int value)
 {
-	struct snd_ac97_gpio_priv *gpio_priv =
-		container_of(chip, struct snd_ac97_gpio_priv, gpio_chip);
+	struct snd_ac97_gpio_priv *gpio_priv = gpiochip_get_data(chip);
 	struct snd_soc_codec *codec = gpio_to_codec(chip);
 
 	gpio_priv->gpios_set &= ~(1 << offset);
@@ -145,7 +143,7 @@
 	gpio_priv->gpio_chip.parent = codec->dev;
 	gpio_priv->gpio_chip.base = -1;
 
-	ret = gpiochip_add(&gpio_priv->gpio_chip);
+	ret = gpiochip_add_data(&gpio_priv->gpio_chip, gpio_priv);
 	if (ret != 0)
 		dev_err(codec->dev, "Failed to add GPIOs: %d\n", ret);
 	return ret;
diff --git a/tools/gpio/Makefile b/tools/gpio/Makefile
index 4d198d5..c155d6b 100644
--- a/tools/gpio/Makefile
+++ b/tools/gpio/Makefile
@@ -1,5 +1,5 @@
 CC = $(CROSS_COMPILE)gcc
-CFLAGS += -Wall -g -D_GNU_SOURCE
+CFLAGS += -O2 -Wall -g -D_GNU_SOURCE
 
 all: lsgpio
 
diff --git a/tools/gpio/lsgpio.c b/tools/gpio/lsgpio.c
index 1124da3..eb3f56e 100644
--- a/tools/gpio/lsgpio.c
+++ b/tools/gpio/lsgpio.c
@@ -147,7 +147,7 @@
 
 int main(int argc, char **argv)
 {
-	const char *device_name;
+	const char *device_name = NULL;
 	int ret;
 	int c;